USER MANUAL - Kramer Electronics Japan Homepage

USER MANUAL - Kramer Electronics Japan Homepage
Kramer Electronics, Ltd.
USER MANUAL
Models:
PT-110, XGA Line Transmitter
WP-110, XGA Line Transmitter
PT-120, XGA Line Receiver
TP-120, XGA Line Receiver
Contents
Contents
1
2
3
3.1
3.2
3.3
3.4
3.5
3.6
3.7
4
4.1
Introduction
Getting Started
Overview
About the Power Connect Feature
Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP)
PT-110 XGA Line Transmitter
WP-110 XGA Line Transmitter
PT-120 XGA Line Receiver
TP-120 XGA Line Receiver
Achieving the Best Performance
Your XGA Line Transmitter(s) / Receiver
Your PT-110 XGA Line Transmitter
1
1
1
2
2
3
3
3
4
4
4
5
4.1.1
4.1.2
Your PT-110 XGA Line Transmitter (Topside)
Your PT-110 XGA Line Transmitter (Underside)
5
5
4.2
4.3
Your WP-110 XGA Line Transmitter
Your PT-120 XGA Line Receiver
6
7
4.3.1
4.3.2
Your PT-120 XGA Line Receiver (Topside)
Your PT-120 XGA Line Receiver (Underside)
7
8
4.4
Your TP-120 XGA Line Receiver
9
4.4.1
4.4.2
Your TP-120 XGA Line Receiver (Topside)
Your TP-120 XGA Line Receiver (Underside)
9
10
5
5.1
5.2
6
Using the XGA Line Transmitter(s) / Receiver
Installing the WP-110 XGA Line Transmitter
Wiring the CAT 5 LINE IN / LINE OUT RJ-45 Connectors
Technical Specifications
11
12
12
13
Figures
Figure 1: PT-110 Topside
Figure 2: PT-110 Underside
Figure 3: WP-110 XGA Line Transmitter
Figure 4: PT-120 XGA Line Receiver (Topside)
Figure 5: PT-120 XGA Line Receiver (Underside)
Figure 6: TP-120 XGA Line Receiver (Topside)
Figure 7: TP-120 XGA Line Receiver (Underside)
Figure 8: XGA-to-Twisted Pair Transmitter and Receiver System via UTP Cable
Figure 9: CAT 5 PINOUT
5
5
6
7
8
9
10
11
12
i
Contents
Tables
Table 1: PT-110 Topside Features
Table 2: PT-110 Underside Features
Table 3: WP-110 XGA Line Transmitter Features
Table 4: PT-120 XGA Line Receiver (Topside) Features
Table 5: PT-120 XGA Line Receiver (Underside) Features
Table 6: TP-120 XGA Line Receiver (Topside) Features
Table 7: TP-120 XGA Line Receiver (Underside) Features
Table 8: CAT 5 PINOUT
Table 9: Technical Specifications of the PT-110 / WP-110 / PT-120 / TP-120
ii
5
5
7
8
8
9
10
12
13
KRAMER: SIMPLE CREATIVE TECHNOLOGY
ADDENDUM (this data is included at the end of the Overview section)
This addendum adds the following information to the user manual:
Caution – No operator-serviceable parts inside unit.
Warning – Use only the Kramer Electronics input power
wall adapter that is provided with this unit1.
Warning – Disconnect power and unplug unit from wall
before installing or removing device or servicing unit.
1 For example: model number AD2512C, part number 2535-000251
2900-9999992
A1
Introduction
1
Introduction
Welcome to Kramer Electronics (since 1981): a world of unique, creative and
affordable solutions to the infinite range of problems that confront the video,
audio and presentation professional on a daily basis. In recent years, we have
redesigned and upgraded most of our line, making the best even better! Our
500-plus different models now appear in 8 Groups1, which are clearly defined
by function. Congratulations on purchasing your Kramer Pico TOOLS
PT-110 XGA Line Transmitter, Kramer Wall Plate WP-110 XGA Line
Transmitter, Kramer Pico TOOLS PT-120 XGA Line Receiver, and/or
Kramer TOOLS TP-120 XGA Line Receiver, which are ideal for:
Presentation and multimedia applications
Long range graphics distribution for schools, hospitals, security, and stores
The package includes the following items:
PT-110 XGA Line Transmitter or WP-110 XGA Line Transmitter or
PT-120 XGA Line Receiver or TP-120 XGA Line Receiver
Power adapter (12V DC Input) and this user manual2
2
Getting Started
We recommend that you:
Unpack the equipment carefully and save the original box and packaging
materials for possible future shipment
Review the contents of this user manual
Use Kramer high performance high resolution cables3
3
Overview
This section describes:
The power connect feature, see section 3.1
Using shielded twisted pair (STP) / unshielded twisted pair (UTP), see
section 3.2
A summary of the PT-110 XGA Line Transmitter, see section 3.3
1 GROUP 1: Distribution Amplifiers; GROUP 2: Video and Audio Switchers, Matrix Switchers and Controllers; GROUP 3:
Video, Audio, VGA/XGA Processors; GROUP 4: Interfaces and Sync Processors; GROUP 5: Twisted Pair Interfaces;
GROUP 6: Accessories and Rack Adapters; GROUP 7: Scan Converters and Scalers; and GROUP 8: Cables and Connectors
2 Download up-to-date Kramer user manuals from the Internet at this URL: http://www.kramerelectronics.com
3 The complete list of Kramer cables is on our Web site at http://www.kramerelectronics.com
1
Overview
A summary of the WP-110 XGA Line Transmitter, see section 3.4
A summary of the PT-120 XGA Line Receiver, see section 3.5
A summary of the TP-120 XGA Line Receiver, see section 3.6
Recommendations for achieving the best performance, see section 3.7
3.1 About the Power Connect Feature
The Power Connect feature applies as long as the cable can carry power. The
distance does not exceed 50 meters on standard CAT5 cable, for longer
distances, heavy gauge cable should be used1.
For a CAT5 cable exceeding a distance of 50 meters, separate power supplies
should be connected to the transmitter and to the receiver simultaneously.
3.2 Shielded Twisted Pair (STP) / Unshielded Twisted Pair (UTP)
The decision whether to use shielded twisted pair (STP) cable or unshielded
twisted pair (UTP) cable depends on the nature of the application.
It is recommended that in applications with high interference, shielded
twisted pair (STP) cable is used. However, the shield itself does create a
capacitance that degrades the frequency response of the machines. For shorter
distances, of 50m or so, shielded twisted pair (STP) cable is preferred because
it provides protection from interference (degradation is not apparent).
For a long range applications, unshielded twisted pair (UTP) cable is
preferred. However, the unshielded twisted pair (UTP) cable should be installed far
away from electric cables, motors and so on, which are prone to create electrical
interference.
1 CAT5 cable is still suitable for the video/audio transmission, but not for feeding the power at these distances
2
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Overview
3.3 PT-110 XGA Line Transmitter
Using a XGA Line Transmitter—the PT-110 or WP-110—with the PT-120
or TP-120 constitutes a VGA/XGA-to-Twisted Pair Transmitter and
Receiver.
The Kramer Pico TOOLS PT-110 is an XGA line transmitter that receives an
XGA signal and transmits it over a CAT 5 cable to the PT-120 or TP-120
receiver. In particular, the PT-110:
Has a resolution of up to UXGA
Can use the simplest UTP CAT 5 cables, and performs even better with
higher quality cables
Has the power connect feature1
Is 12VDC fed
3.4 WP-110 XGA Line Transmitter
The Kramer Wall Plate WP-110 is an XGA line transmitter—available in
three versions: one for the USA, one for Belgium and Germany, and one for
the UK and most of Europe2—that receives an XGA signal and transmits it over
a CAT 5 cable to the PT-120 or TP-120 receiver. In particular, the WP-110:
Has a resolution of up to UXGA
Can use the simplest UTP CAT 5 cables, however, it benefits from better
quality cables
Has the power connect feature1
Is powered via a standard 12 Volt DC feed
3.5 PT-120 XGA Line Receiver
The Kramer Pico TOOLS PT-120 is an XGA line receiver that receives a
coded CAT5 signal transmitted by either the WP-110 or the PT-110, decodes
it and converts it to an XGA output. In particular, the PT-120:
Has an operating range of more than 300 ft. (more than 100 meters) using
standard CAT5 cable and the WP-110 or the PT-110
Includes EQ. and level controls
Has the power connect feature3
Is 12VDC fed
1 Powering via the CAT5 cable from either the receiver or the transmitter is good for 100 meters. Above it, both sides should
be fed with power
2 Excluding Belgium and Germany
3 Powering via the CAT5 cable from either the receiver or the transmitter is good for 60 meters. Above it, both sides should
be fed with power
3
Your XGA Line Transmitter(s) / Receiver
3.6 TP-120 XGA Line Receiver
The Kramer TOOLS TP-120 is an XGA line receiver that receives a coded
CAT 5 signal transmitted by either the WP-110 or the PT-110, decodes it and
converts it to an XGA output. In particular, the TP-120:
Has an operating range of more than 300 ft. (more than 100 meters) using
standard CAT 5 cable and the WP-110 or the PT-110
Includes EQ. and level controls
Has the power connect feature1
Is 12VDC fed
3.7 Achieving the Best Performance
Achieving the best performance means:
Connecting only good quality connection cables, thus avoiding
interference, deterioration in signal quality due to poor matching, and elevated
noise levels (often associated with low quality cables)
Avoiding interference from neighboring electrical appliances and
positioning your XGA Line Transmitter(s) / Receiver away from moisture,
excessive sunlight and dust
4
Your XGA Line Transmitter(s) / Receiver
This section defines the XGA Line Transmitter(s) / Receiver:
PT-110 XGA Line Transmitter (see section 4.1)
WP-110 XGA Line Transmitter (see section 4.2)
PT-120 XGA Line Receiver (see section 4.3)
TP-120 XGA Line Receiver (see section 4.4)
1 Powering via the CAT5 cable from either the receiver or the transmitter is good for 100 meters. Above it, both sides should
be fed with power
4
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your XGA Line Transmitter(s) / Receiver
4.1 Your PT-110 XGA Line Transmitter
This section describes the PT-110 XGA Line Transmitter
Topside (see section 4.1.1)
Underside (see section 4.1.2)
4.1.1
Your PT-110 XGA Line Transmitter (Topside)
Figure 1 and Table 1 define the PT-110:
Table 1: PT-110 Topside Features
#
Feature
Function
1
XGA INPUT
HD15F Connector
Connect to the XGA source
2
LINE OUTPUT
RJ-45 Connector
Connects to the LINE IN RJ-45
connector on the PT-120 or TP-120 XGA
1
Line Receiver
3
12V DC
+12V DC connector for powering the unit
4
ON LED
Illuminates when receiving power
Figure 1: PT-110 Topside
4.1.2
Your PT-110 XGA Line Transmitter (Underside)
Figure 2 and Table 2 define the underside of the PT-110:
Table 2: PT-110 Underside Features
#
Feature
1
HS4
Switch
2
VS4
Switch
Function
Slide the switch to the left2 to change
the HS polarity to (NEG.) negative
polarity3; slide the switch to the right
(NORM) to retain the polarity
Slide the switch to the left2 to change
the VS polarity to (NEG.) negative
polarity3; slide the switch to the right
(NORM) to retain the polarity
Figure 2: PT-110 Underside
1 Using a UTP cable with CAT 5 connectors at both ends (the PINOUT is defined in Table 8 and Figure 9)
2 By default, both switches are set to the right
3 Downgoing syncs
4 SYNC
5
Your XGA Line Transmitter(s) / Receiver
4.2 Your WP-110 XGA Line Transmitter
The WP-110 is available in three versions: one for the US, one for Belgium
and Germany, and one for the UK and most of Europe1, as Figure 3 and Table
3 define:
Figure 3: WP-110 XGA Line Transmitter
1 Excluding Belgium and Germany
6
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your XGA Line Transmitter(s) / Receiver
Table 3: WP-110 XGA Line Transmitter Features
#
Feature
Function
1
XGA IN HD15F Connector
2
ON LED
Illuminates when receiving power
3
HS4 Switch
Slide the switch to the left1 to change the HS polarity to (NEG.) negative
2
polarity ; slide the switch to the right (NORM.) to retain the polarity
4
VS3 Switch
5
Connect to the XGA source
Slide the switch to the left1 to change the VS polarity to (NEG.) negative
polarity2; slide the switch to the right (NORM.) to retain the polarity
LINE OUT RJ-45 Connector Connects to the LINE IN RJ-45 connector on the PT-120 or TP-120
XGA Line Receiver 4
6
POWER
SUPPLY
GND PIN
Connect (-) to the Ground
+12 VDC PIN
Connect (+) to the connector for powering the unit
4.3 Your PT-120 XGA Line Receiver
This section describes the PT-120 XGA Line Receiver
Topside (see section 4.3.1)
Underside (see section 4.3.2)
4.3.1
Your PT-120 XGA Line Receiver (Topside)
Figure 4 and Table 4 define the topside of the PT-120 XGA Line Receiver:
Figure 4: PT-120 XGA Line Receiver (Topside)
1 By default, both switches are set to the right
2 Downgoing syncs
3 SYNC
4 Using a UTP cable with CAT 5 connectors at both ends (the PINOUT is defined in Table 8 and Figure 9)
7
Your XGA Line Transmitter(s) / Receiver
Table 4: PT-120 XGA Line Receiver (Topside) Features
#
1
2
Feature
Function
XGA OUTPUT HD15F Connector Connect to the XGA acceptor
Connects to the LINE OUT RJ-45 connector on the PT-110 or
LINE INPUT RJ-45 Connector
1
WP-110 XGA Line Receiver
12V DC
+12V DC connector for powering the unit
ON LED
Illuminates when receiving power
2
LEVEL Trimmer
Adjusts the output signal level
3
2
EQ. Trimmer
Adjusts the cable compensation equalization level
3
4
5
6
4.3.2
Your PT-120 XGA Line Receiver (Underside)
Figure 5 and Table 5 define the underside of the PT-120 XGA Line Receiver:
Figure 5: PT-120 XGA Line Receiver (Underside)
Table 5: PT-120 XGA Line Receiver (Underside) Features
# Feature
1 VS4 Switch
2
HS4 Switch
Function
Slide the switch to the right5 to change the VS polarity; slide the switch to the left to
retain the polarity
Slide the switch to the right5 to change the HS polarity; slide the switch to the left to
retain the polarity
1 Using a UTP cable with CAT 5 connectors at both ends (the PINOUT is defined in Table 8 and Figure 9)
2 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
3 Degradation and VGA/XGA signal loss can result from using long cables (due to stray capacitance), sometimes leading to a
total loss of sharpness in high-resolution signals
4 SYNC
5 By default, both switches are set to the left
8
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Your XGA Line Transmitter(s) / Receiver
4.4 Your TP-120 XGA Line Receiver
This section describes the TP-120 XGA Line Receiver
Topside (see section 4.4.1)
Underside (see section 4.4.2)
4.4.1
Your TP-120 XGA Line Receiver (Topside)
Figure 6 and Table 6 define the topside of the TP-120 XGA Line Receiver:
Figure 6: TP-120 XGA Line Receiver (Topside)
Table 6: TP-120 XGA Line Receiver (Topside) Features
# Feature
1 12V DC
2 XGA OUT HD15F Connector
3 LINE IN RJ-45 Connector
4
5
6
ON LED
LEVEL Trimmer
EQ.3 Trimmer
Function
+12V DC connector for powering the unit
Connect to the XGA acceptor
Connects to the LINE OUT RJ-45 connector on the PT-110 or
WP-110 XGA Line Receiver 1
Illuminates when receiving power
Adjusts2 the output signal level
Adjusts2 the cable compensation equalization level
1 Using a UTP cable with CAT 5 connectors at both ends (the PINOUT is defined in Table 8 and Figure 9)
2 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
3 Degradation and VGA/XGA signal loss can result from using long cables (due to stray capacitance), sometimes leading to a
total loss of sharpness in high-resolution signals
9
Your XGA Line Transmitter(s) / Receiver
4.4.2
Your TP-120 XGA Line Receiver (Underside)
Figure 7 and Table 7 define the underside of the TP-120 XGA Line Receiver:
Figure 7: TP-120 XGA Line Receiver (Underside)
Table 7: TP-120 XGA Line Receiver (Underside) Features
# Feature
1 H SYNC
Switch
2 V SYNC
Switch
Function
Slide the switch up1 to change the H SYNC polarity; slide the switch down to retain
the polarity
Slide the switch up1 to change the V SYNC polarity; slide the switch down to retain
the polarity
1 By default, both switches are set down for normal V SYNC and H SYNC polarity
10
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Using the XGA Line Transmitter(s) / Receiver
5
Using the XGA Line Transmitter(s) / Receiver
You can use the PT-1101 XGA Line Transmitter and the TP-120 XGA Line
Receiver to configure an XGA-to-Twisted Pair Transmitter and Receiver system.
To connect the PT-110 XGA Line Transmitter with the TP-120 XGA Line
Receiver, as the example in Figure 8 illustrates, do the following:
1. On the PT-110, connect the XGA source (for example, the HD-15 output
from a computer’s graphics card) to the XGA INPUT HD15F connector.
2. On the TP-120, connect the XGA OUT HD15F connector to the XGA
acceptor (for example, a monitor).
3. Connect the LINE OUTPUT RJ-45 connector on the PT-110 to the LINE
IN RJ-45 connector on the TP-120, via UTP cabling (with a range of
more than 300ft (>100m)).
4. On both2 the PT-110 and the TP-120, connect the 12V DC power adapter
to the power socket and connect the adapter to the mains electricity.
The signal from the XGA source is transmitted via CAT 5 cable, decoded
and converted at the XGA OUT HD15F connector to the XGA acceptor.
5. On the TP-120, adjust3 the output signal level and/or cable compensation
equalization level, if required.
6. If necessary, set the H SYNC and V SYNC switches4, on the undersides
of the units.
Figure 8: XGA-to-Twisted Pair Transmitter and Receiver System via UTP Cable
1 You can use the WP-110 (not shown in Figure 8) instead of the PT-110. For details, see section 5.1
2 For distances of up to 100 meters you can connect a power adapter to either the PT-110 or TP-120. Above it, both sides
should be fed with power
3 Use a screwdriver to carefully rotate the trimmer, adjusting the appropriate level
4 By default, both switches are set for normal H SYNC and V SYNC polarity
11
Using the XGA Line Transmitter(s) / Receiver
5.1 Installing the WP-110 XGA Line Transmitter
To install your WP-110 XGA Line Transmitter:
1. Connect the LINE OUT RJ-45 connector to the pre-installed UTP wiring in
the wall box opening that connects via UTP cabling to the LINE IN RJ-45
connector of the PT-120 or TP-120.
2. Connect your 12V DC power supply to the POWER SUPPLY pins1,
taking care that polarity is correct.
3. Insert the WP-110 directly into the wall box opening, and then mount the
front panel securely using the screws.
4. Connect the XGA source to the XGA IN HD15F connector.
5.2 Wiring the CAT 5 LINE IN / LINE OUT RJ-45 Connectors
Table 8 and Figure 9 define the CAT 5 PINOUT, using a straight pin to pin
cable with RJ-45 connectors:
Figure 9: CAT 5 PINOUT
Table 8: CAT 5 PINOUT
EIA /TIA 568A
PIN
1
2
3
4
5
6
7
8
Wire Color
Green / White
Green
Orange / White
Blue
Blue / White
Orange
Brown / White
Brown
EIA /TIA 568B
PIN
1
2
3
4
5
6
7
8
Wire Color
Orange / White
Orange
Green / White
Blue
Blue / White
Green
Brown / White
Brown
Pair 1
4 and 5
Pair 1
Pair 2
3 and 6
Pair 2
4 and 5
1 and 2
Pair 3
1 and 2
Pair 3
3 and 6
Pair 4
7 and 8
Pair 4
7 and 8
1 Connect the wire labeled “+” to the +12V pin, and the wire labeled “–” to the GND pin
12
KRAMER: SIMPLE CREATIVE TECHNOLOGY
Technical Specifications
6
Technical Specifications
Table 9 includes the technical specifications:
1
Table 9: Technical Specifications of the PT-110 / WP-110 / PT-120 / TP-120
INPUTS:
OUTPUTS:
MAX. OUTPUT
LEVEL:
RESOLUTION:
2
DIFF. GAIN :
2
DIFF. PHASE
2
K-FACTOR :
2
S/N RATIO :
CONTROLS:
PT-110
1 VGA / UXGA on
an HD15 connector
1 RJ-45 LINE
OUTPUT connector
WP-110
1 VGA / UXGA on an HD15
connector
1 RJ-45 LINE OUT
connector
PT-120
1 RJ-45 LINE IN
connector
1 VGA / UXGA on an
HD15 connector
1.5Vpp
TP-120
1 RJ-45 LINE IN
connector
1 VGA / UXGA on an
HD15 connector
1.4Vpp
Up to UXGA
2.9% (worst case)
0.3 Deg (worst case)
<0.05%
69dB (worst case)
–7.7dB to +3.1dB,
130m level,
0dB to +25dB
EQ. @ 50MHz
COUPLING:
AC
AC
DC
POWERSOURCE: 12 VDC 60mA
12 VDC 60mA
12 VDC 175mA
DIMENSIONS:
6cm x 6.5cm x 2.5cm USA: 6.9cm x 3.8cm x 11.4cm 6cm x 6.5cm x 2.5cm
(2.36" x 2.56" x 1",
(2.36" x 2.56" x 1",
(2.72" x 1.5" x 4.5", W, D, H)
W, D, H)
W, D, H)
Belgium and Germany:
8cm x 3.8cm x 8cm
(3.15" x 1.5" x 3.15", W, D, H)
–7.5dB to +4.4dB,
130m level, 0dB to
+33dBm 130m,
EQ. @ 50MHz
AC
12 VDC 160mA
12cm x 7.5cm x 2.5cm
(4.7" x 0.98" x 2.95",
W, D, H)
3
WEIGHT:
0.14 kg. (0.31 lbs.)
approx.
ACCESSORIES: Power supply
UK and most of Europe :
8.6cm x 3.8cm x 8.6cm
(3.39" x 1.5" x 3.39", W, D, H)
0.14 kg. (0.31 lbs.) approx.
0.14 kg. (0.31 lbs.)
approx.
0.3kg. (0.66lbs.)
approx.
1 Specifications are subject to change without notice
2 For the Transmitter/Receiver pair
3 Excluding Belgium and Germany
13
LIMITED WARRANTY
Kramer Electronics (hereafter Kramer) warrants this product free from defects in material and workmanship under the
following terms.
HOW LONG IS THE WARRANTY
Labor and parts are warranted for seven years from the date of the first customer purchase.
WHO IS PROTECTED?
Only the first purchase customer may enforce this warranty.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as below, this warranty covers all defects in material or workmanship in this product. The following are not covered
by the warranty:
1.
2.
3.
Any product which is not distributed by Kramer, or which is not purchased from an authorized Kramer dealer. If you are
uncertain as to whether a dealer is authorized, please contact Kramer at one of the agents listed in the web site
www.kramerelectronics.com.
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
i)
Accident, misuse, abuse, neglect, fire, water, lightning or other acts of nature
ii)
Product modification, or failure to follow instructions supplied with the product
iii)
Repair or attempted repair by anyone not authorized by Kramer
iv)
Any shipment of the product (claims must be presented to the carrier)
v)
Removal or installation of the product
vi)
Any other cause, which does not relate to a product defect
vii)
Cartons, equipment enclosures, cables or accessories used in conjunction with the product
WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR
We will pay labor and material expenses for covered items. We will not pay for the following:
1.
2.
3.
Removal or installations charges.
Costs of initial technical adjustments (set-up), including adjustment of user controls or programming. These costs are the
responsibility of the Kramer dealer from whom the product was purchased.
Shipping charges.
HOW YOU CAN GET WARRANTY SERVICE
1.
2.
3.
To obtain service on you product, you must take or ship it prepaid to any authorized Kramer service center.
Whenever warranty service is required, the original dated invoice (or a copy) must be presented as proof of warranty coverage,
and should be included in any shipment of the product. Please also include in any mailing a contact name, company, address, and
a description of the problem(s).
For the name of the nearest Kramer authorized service center, consult your authorized dealer.
LIMITATION OF IMPLIED WARRANTIES
All implied warranties, including warranties of merchantability and fitness for a particular purpose, are limited in duration to
the length of this warranty.
EXCLUSION OF DAMAGES
The liability of Kramer for any effective products is limited to the repair or replacement of the product at our option. Kramer
shall not be liable for:
1.
2.
Damage to other property caused by defects in this product, damages based upon inconvenience, loss of use of the product, loss
of time, commercial loss; or:
Any other damages, whether incidental, consequential or otherwise. Some countries may not allow limitations on how long an
implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which vary from place to place.
NOTE: All products returned to Kramer for service must have prior approval. This may be obtained from your dealer.
This equipment has been tested to determine compliance with the requirements of:
EN-50081:
"Electromagnetic compatibility (EMC);
generic emission standard.
Part 1: Residential, commercial and light industry"
EN-50082:
"Electromagnetic compatibility (EMC) generic immunity standard.
Part 1: Residential, commercial and light industry environment".
CFR-47:
FCC Rules and Regulations:
Part 15: “Radio frequency devices
Subpart B – Unintentional radiators”
CAUTION!
Servicing the machines can only be done by an authorized Kramer technician. Any user who makes changes or modifications to
the unit without the expressed approval of the manufacturer will void user authority to operate the equipment.
Use the supplied DC power supply to feed power to the machine.
Please use recommended interconnection cables to connect the machine to other components.
14
KRAMER: SIMPLE CREATIVE TECHNOLOGY
For the latest information on our products and a list of Kramer
distributors, visit our Web site: www.kramerelectronics.com,
where updates to this user manual may be found.
We welcome your questions, comments and feedback.
Safety Warning:
Disconnect the unit from the power supply before
opening/servicing.
Caution
Kramer Electronics, Ltd.
Web site: www.kramerelectronics.com
E-mail: info@kramerel.com
P/N: 2900-000085 REV 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising