Extron electronics 450 Plus Setup guide

Extron electronics 450 Plus Setup guide
Setup Guide
CrossPoint 450 Plus Series
MAV Plus Series
Large Scale Matrix Switchers
Extron USA - West
Headquarters
+800.633.9876
Inside USA / Canada Only
+1.714.491.1500
+1.714.491.1517 FAX
Extron USA - East
Extron Europe
Extron Asia
Extron Japan
Extron China
Extron Middle East
+800.633.9876
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
+1.919.863.1794
+1.919.863.1797 FAX
+31.33.453.4040
+31.33.453.4050 FAX
+65.6383.4400
+65.6383.4664 FAX
Inside USA / Canada Only
Inside Europe Only
Inside Asia Only
© 2009 Extron Electronics. All rights reserved.
Inside China Only
+86.21.3760.1568
+86.21.3760.1566 FAX
68-521-53 Rev. A
10 09
Precautions
Safety Instructions • English
This symbol is intended to alert the user of important
operating and maintenance (servicing) instructions in
the literature provided with the equipment.
This symbol is intended to alert the user of the
presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of
electric shock.
Caution
Read Instructions • Read and understand all safety and operating
instructions before using the equipment.
Retain Instructions • The safety instructions should be kept for future
reference.
Follow Warnings • Follow all warnings and instructions marked on the
equipment or in the user information.
Avoid Attachments • Do not use tools or attachments that are not
recommended by the equipment manufacturer because they may be
hazardous.
Consignes de Sécurité • Français
Ce symbole sert à avertir l’utilisateur que la
documentation fournie avec le matériel contient des
instructions importantes concernant l’exploitation et
la maintenance (réparation).
Ce symbole sert à avertir l’utilisateur de la présence
dans le boîtier de l’appareil de tensions dangereuses
non isolées posant des risques d’électrocution.
Attention
Lire les instructions• Prendre connaissance de toutes les consignes de
sécurité et d’exploitation avant d’utiliser le matériel.
Conserver les instructions• Ranger les consignes de sécurité afin de pouvoir
les consulter à l’avenir.
Respecter les avertissements • Observer tous les avertissements et consignes
marqués sur le matériel ou présentés dans la documentation utilisateur.
Eviter les pièces de fixation • Ne pas utiliser de pièces de fixation ni d’outils
non recommandés par le fabricant du matériel car cela risquerait de poser
certains dangers.
Sicherheitsanleitungen • Deutsch
Dieses Symbol soll dem Benutzer in der im
Lieferumfang enthaltenen Dokumentation
besonders wichtige Hinweise zur Bedienung und
Wartung (Instandhaltung) geben.
Dieses Symbol soll den Benutzer darauf aufmerksam
machen, daß im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen, die nicht isoliert
sind und die einen elektrischen Schock verursachen
können, herrschen.
Achtung
Lesen der Anleitungen • Bevor Sie das Gerät zum ersten Mal verwenden,
sollten Sie alle Sicherheits-und Bedienungsanleitungen genau durchlesen
und verstehen.
Aufbewahren der Anleitungen • Die Hinweise zur elektrischen Sicherheit
des Produktes sollten Sie aufbewahren, damit Sie im Bedarfsfall darauf
zurückgreifen können.
Befolgen der Warnhinweise • Befolgen Sie alle Warnhinweise und
Anleitungen auf dem Gerät oder in der Benutzerdokumentation.
Keine Zusatzgeräte • Verwenden Sie keine Werkzeuge oder Zusatzgeräte,
die nicht ausdrücklich vom Hersteller empfohlen wurden, da diese eine
Gefahrenquelle darstellen können.
Instrucciones de seguridad • Español
Este símbolo se utiliza para advertir al usuario
sobre instrucciones importantes de operación y
mantenimiento (o cambio de partes) que se desean
destacar en el contenido de la documentación
suministrada con los equipos.
Este símbolo se utiliza para advertir al usuario sobre
la presencia de elementos con voltaje peligroso sin
protección aislante, que puedan encontrarse dentro
de la caja o alojamiento del producto, y que puedan
representar riesgo de electrocución.
Precaucion
Leer las instrucciones • Leer y analizar todas las instrucciones de operación y
seguridad, antes de usar el equipo.
Conservar las instrucciones • Conservar las instrucciones de seguridad para
futura consulta.
Obedecer las advertencias • Todas las advertencias e instrucciones marcadas
en el equipo o en la documentación del usuario, deben ser obedecidas.
Evitar el uso de accesorios • No usar herramientas o accesorios que no
sean especificamente recomendados por el fabricante, ya que podrian
implicar riesgos.
Warning
Power sources • This equipment should be operated only from the power source
indicated on the product. This equipment is intended to be used with a main power
system with a grounded (neutral) conductor. The third (grounding) pin is a safety
feature, do not attempt to bypass or disable it.
Power disconnection • To remove power from the equipment safely, remove all power
cords from the rear of the equipment, or the desktop power module (if detachable),
or from the power source receptacle (wall plug).
Power cord protection • Power cords should be routed so that they are not likely to be
stepped on or pinched by items placed upon or against them.
Servicing • Refer all servicing to qualified service personnel. There are no userserviceable parts inside. To prevent the risk of shock, do not attempt to service
this equipment yourself because opening or removing covers may expose you to
dangerous voltage or other hazards.
Slots and openings • If the equipment has slots or holes in the enclosure, these are
provided to prevent overheating of sensitive components inside. These openings
must never be blocked by other objects.
Lithium battery • There is a danger of explosion if battery is incorrectly
replaced. Replace it only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the manufacturer’s
instructions.
Avertissement
Alimentations• Ne faire fonctionner ce matériel qu’avec la source d’alimentation
indiquée sur l’appareil. Ce matériel doit être utilisé avec une alimentation principale
comportant un fil de terre (neutre). Le troisième contact (de mise à la terre) constitue
un dispositif de sécurité : n’essayez pas de la contourner ni de la désactiver.
Déconnexion de l’alimentation• Pour mettre le matériel hors tension sans danger,
déconnectez tous les cordons d’alimentation de l’arrière de l’appareil ou du module
d’alimentation de bureau (s’il est amovible) ou encore de la prise secteur.
Protection du cordon d’alimentation • Acheminer les cordons d’alimentation de
manière à ce que personne ne risque de marcher dessus et à ce qu’ils ne soient pas
écrasés ou pincés par des objets.
Réparation-maintenance • Faire exécuter toutes les interventions de réparationmaintenance par un technicien qualifié. Aucun des éléments internes ne peut être
réparé par l’utilisateur. Afin d’éviter tout danger d’électrocution, l’utilisateur ne doit
pas essayer de procéder lui-même à ces opérations car l’ouverture ou le retrait des
couvercles risquent de l’exposer à de hautes tensions et autres dangers.
Fentes et orifices • Si le boîtier de l’appareil comporte des fentes ou des orifices, ceux-ci
servent à empêcher les composants internes sensibles de surchauffer. Ces ouvertures
ne doivent jamais être bloquées par des objets.
Lithium Batterie • Il a danger d’explosion s’ll y a remplacment incorrect de la batterie.
Remplacer uniquement avec une batterie du meme type ou d’un ype equivalent
recommande par le constructeur. Mettre au reut les batteries usagees conformement
aux instructions du fabricant.
Vorsicht
Stromquellen • Dieses Gerät sollte nur über die auf dem Produkt angegebene
Stromquelle betrieben werden. Dieses Gerät wurde für eine Verwendung mit einer
Hauptstromleitung mit einem geerdeten (neutralen) Leiter konzipiert. Der dritte
Kontakt ist für einen Erdanschluß, und stellt eine Sicherheitsfunktion dar. Diese
sollte nicht umgangen oder außer Betrieb gesetzt werden.
Stromunterbrechung • Um das Gerät auf sichere Weise vom Netz zu trennen, sollten
Sie alle Netzkabel aus der Rückseite des Gerätes, aus der externen Stomversorgung
(falls dies möglich ist) oder aus der Wandsteckdose ziehen.
Schutz des Netzkabels • Netzkabel sollten stets so verlegt werden, daß sie nicht im
Weg liegen und niemand darauf treten kann oder Objekte darauf- oder unmittelbar
dagegengestellt werden können.
Wartung • Alle Wartungsmaßnahmen sollten nur von qualifiziertem Servicepersonal
durchgeführt werden. Die internen Komponenten des Gerätes sind wartungsfrei.
Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall, dieses
Gerät selbst öffnen, da beim Entfernen der Abdeckungen die Gefahr eines
elektrischen Schlags und/oder andere Gefahren bestehen.
Schlitze und Öffnungen • Wenn das Gerät Schlitze oder Löcher im Gehäuse aufweist,
dienen diese zur Vermeidung einer Überhitzung der empfindlichen Teile im
Inneren. Diese Öffnungen dürfen niemals von anderen Objekten blockiert werden.
Litium-Batterie • Explosionsgefahr, falls die Batterie nicht richtig ersetzt
wird. Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen
vergleichbaren Batterietyp, der auch vom Hersteller empfohlen wird. Entsorgen Sie
verbrauchte Batterien bitte gemäß den Herstelleranweisungen.
Advertencia
Alimentación eléctrica • Este equipo debe conectarse únicamente a la fuente/tipo
de alimentación eléctrica indicada en el mismo. La alimentación eléctrica de este
equipo debe provenir de un sistema de distribución general con conductor neutro
a tierra. La tercera pata (puesta a tierra) es una medida de seguridad, no puentearia
ni eliminaria.
Desconexión de alimentación eléctrica • Para desconectar con seguridad la acometida
de alimentación eléctrica al equipo, desenchufar todos los cables de alimentación
en el panel trasero del equipo, o desenchufar el módulo de alimentación (si fuera
independiente), o desenchufar el cable del receptáculo de la pared.
Protección del cables de alimentación • Los cables de alimentación eléctrica se deben
instalar en lugares donde no sean pisados ni apretados por objetos que se puedan
apoyar sobre ellos.
Reparaciones/mantenimiento • Solicitar siempre los servicios técnicos de personal
calificado. En el interior no hay partes a las que el usuario deba acceder. Para evitar
riesgo de electrocución, no intentar personalmente la reparación/mantenimiento
de este equipo, ya que al abrir o extraer las tapas puede quedar expuesto a voltajes
peligrosos u otros riesgos.
Ranuras y aberturas • Si el equipo posee ranuras o orificios en su caja/alojamiento,
es para evitar el sobrecalientamiento de componentes internos sensibles. Estas
aberturas nunca se deben obstruir con otros objetos.
Batería de litio • Existe riesgo de explosión si esta batería se coloca en la posición
incorrecta. Cambiar esta batería únicamente con el mismo tipo (o su equivalente)
recomendado por el fabricante. Desachar las baterías usadas siguiendo las
instrucciones del fabricante.
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron USA
1001 East Ball Road
Anaheim, CA 92805
U.S.A.
Europe, Africa, and the Middle East:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
Asia:
Extron Asia
135 Joo Seng Road #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Japan:
Extron Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
China:
Extron China
686 Ronghua Road, Songjiang
District
Shanghai 201611
China
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or nonExtron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
安全须知 • 中文
警告
这个符号提示用户该设备用户手册中
有重要的操作和维护说明。
电源 • 该 设 备 只 能 使 用 产 品 上 标 明 的 电 源 。 设 备
必须使用有地线的供电系统供电。 第三条线
(地线)是安全设施,不能不用或跳过。
这个符号警告用户该设备机壳内有暴
拔掉电源 • 为安全地从设备拔掉电源,请拔掉所有设备后
或桌面电源的电源线,或任何接到市电系统的电源线。
露的危险电压,有触电危险。
电源线保护 • 妥善布线, 避免被踩踏,或重物挤压。
注意
阅读说明书 • 用 户 使 用 该 设 备 前 必 须 阅 读 并 理
解所有安全和使用说明。
保存说明书 • 用户应保存安全说明书以备将来使
用。
遵守警告 • 用户应遵守产品和用户指南上的所有安
全和操作说明。
维护 • 所有维修必须由认证的维修人员进行。 设备内部
没有用户可以更换的零件。为避免出现触电危险不要自
己试图打开设备盖子维修该设备。
通风孔 • 有些设备机壳上有通风槽或孔,它们是用来防止
机内敏感元件过热。 不要用任何东西挡住通风孔。
锂电池 • 不正确的更换电池会有爆炸的危险。 必须使用
与厂家推荐的相同或相近型号的电池。 按照生产厂的
建议处理废弃电池。
避免追加 • 不要使用该产品厂商没有推荐的工具或
追加设备,以避免危险。
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The Class A limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at his
own expense.
N
This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used
with the unit to ensure compliance with FCC emissions limits.
Table of Contents
Chapter One • Introduction..................................................... 1-1
About this Manual..................................................................... 1-2
About the Matrix Switchers................................................... 1-2
Chapter Two • Installation....................................................... 2-1
Rear Panel Installation Features............................................ 2-3
Video and audio connections, sync termination, and external
sync.......................................................................................... 2-3
Remote control connections.................................................. 2-4
BME connection and selection............................................... 2-5
Power connection................................................................... 2-6
Front Panel Configuration Port. ............................................ 2-6
Chapter Three • Front Panel Operation.......................... 3-1
Creating a Tie............................................................................... 3-2
Saving or Recalling a Preset. .................................................. 3-3
Setting the Front Panel Locks (Executive Modes)........... 3-4
Selecting Lock mode 2 or toggling between
mode 2 and mode 0................................................................ 3-4
Selecting Lock mode 2 or toggling between
mode 2 and mode 1................................................................ 3-5
Viewing and Adjusting the Input Audio Level and
Output Volume....................................................................... 3-5
Viewing Ties (and Muting Outputs).................................... 3-6
Chapter Four • Remote Control............................................ 4-1
Selected SIS Commands........................................................... 4-2
Establishing a network (Ethernet) connection..................... 4-2
Connection timeouts...............................................................4-2
Number of connections...........................................................4-3
Verbose mode..........................................................................4-3
Installing and Starting the Control Program................... 4-10
Installing the program.......................................................... 4-10
Starting the program............................................................ 4-11
Accessing the HTML Pages.................................................... 4-13
Configuring for Network Communication.......................... 4-13
Loading the start-up page.................................................... 4-15
All trademarks mentioned in this manual are the properties of their respective owners.
CrossPoint / MAV Matrix Switchers • Table of Contents
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
i
Table of Contents, cont’d
CrossPoint 450 Plus / MAV Plus Matrix Switchers
1
Chapter One
Introduction
About this Manual
About the Matrix Switchers
ii
CrossPoint / MAV Matrix Switchers • Table of Contents
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
Introduction
N For more information on any subject in this guide, refer to
TCP/IP
Network
the CrossPoint 450 Plus / MAV Plus User’s Manual,
available on the Extron DVD or at www.extron.com.
Control
System
BME 0 (red)
12
9
17
18
22
23
24
25
26
27
28
•
•
1-2
CrossPoint 450 Plus Wideband video — Routes a single
video plane (red [R], green [G], or blue [B]).
CrossPoint 450 Plus Sync — Routes a single sync plane
(horizontal [H], vertical [V], or composite sync [S]).
•
MAV Plus Video — Routes a single plane of low
resolution (NTSC/PAL/SECAM) component video (Y, R-Y,
or B-Y), S-video (Y or C), and composite video.
•
MAV Plus Stereo Audio — Routes balanced or
unbalanced stereo audio (two audio planes).
•
MAV Plus Mono Audio — Routes mono audio (one audio
plane).
CrossPoint / MAV Matrix Switchers • Introduction
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
15
22
23
36
39
40
41
42
43
44
26
27
29
28
37
30
31
38
34
35
36
39
40
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
60
61
62
63
46
47
8
9
10
11
12
13
14
15
16
OUTPUTS
INPUTS
75
12345678
10 12 14 16
9 11 13 15
75
50
54
55
56
57
58
51
59
60
52
17
18
21
22
23
24
25
26
19
27
28
29
30
31
32
32
61
BME COMM
BME
ADDRESS
LAN
4
LISTED
1T23
I.T.E.
62
63
64
IN
6
7
8
13
14
15
16
18
19
26
20
27
28
21
29
37
22
30
38
23
31
34
35
36
39
40
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
60
61
62
63
39
40
42
43
44
45
46
35
47
48
36
OUTPUTS 49 - 64
49
50
53
54
55
56
57
58
59
60
61
62
51
63
64
52
64
BME
ADDRESS
LAN
-
4
LISTED
1T23
I.T.E.
+
US
IN
ACT LINK
OUT
38
41
32
33
59
34
37
24
41
58
33
ACT LINK
OUT
BME 4 (vertical)
Projector
ANAHEIM, CA
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
27
28
29
30
31
22
23
24
25
26
27
28
29
30
31
32
34
35
36
37
38
39
40
42
43
44
45
46
47
48
OUTPUTS 33 - 48
4
OUTPUTS
INPUTS
75
38
39
40
5
6
7
8
41
42
43
44
9
10
11
12
46
47
48
13
52
17
14
15
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
BME COMM
BME
ADDRESS
51
75
10 12 14 16
9 11 13 15
19
55
56
21
22
23
24
58
59
60
25
26
27
28
62
63
64
29
30
31
32
LAN
7
8
11
12
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
14
19
18
26
19
27
20
28
21
29
22
30
23
31
22
23
24
25
26
27
28
29
30
31
32
34
35
37
38
39
40
41
42
43
44
47
48
46
32
34
35
36
37
38
39
40
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
39
40
42
26
27
28
29
30
31
43
44
47
48
46
35
36
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
OUTPUTS 49 - 64
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
BME
ADDRESS
49
50
53
54
55
56
57
58
59
60
61
62
63
64
LAN
4
51
52
+
IN
ACT LINK
OUT
1
2
3
4
17
18
19
33
20
5
6
7
8
22
23
9
10
11
12
25
26
27
28
13
14
15
16
29
30
31
32
21
34
35
36
49
50
51
52
39
40
53
54
41
42
43
44
57
58
59
60
45
46
47
48
61
62
63
64
37
24
38
55
56
INPUTS
OUTPUTS 49 - 64
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
OUTPUTS
EXT
SYNC
BME COMM
BME
ADDRESS
LAN
-
4
LISTED
1T23
I.T.E.
38
41
36
1
2
3
4
17
18
19
20
33
34
35
36
49
50
51
52
5
6
7
8
21
22
23
24
37
38
39
40
53
54
55
56
9
10
11
12
25
26
27
28
41
42
43
44
57
58
59
60
13
14
15
16
29
30
31
32
45
46
47
48
61
62
63
64
RESET
3.0A MAX
C
34
37
24
33
41
20
21
33
-
33
45
25
18
24
BME 5 (audio)
OUTPUTS
INPUTS
OUTPUTS 17 - 32
16
23
LISTED
1T23
I.T.E.
ANAHEIM, CA
6
15
22
US
OUTPUTS 33 - 48
10
14
21
45
BME 2 (blue)
OUTPUTS 1 - 16
9
8
13
BME COMM
C
ANAHEIM, CA
5
7
12
20
3
20
54
ACT LINK
OUT
18
61
+
IN
4
6
11
19
2
16
OUTPUTS 17 - 32
57
4
LISTED
1T23
I.T.E.
50
US
3
5
10
18
510
53
-
2
4
9
17
1
12345678
25
OUTPUTS 49 - 64
49
EXT
SYNC
C
3
32
33
41
20
21
2
LAN
26
OUTPUTS 1 - 16
1
36
37
45
25
35
510
16
19
34
8
ACT LINK
15
7
-
14
OUTPUTS 17 - 32
18
6
Sound
System
+
12
5
4
8
11
4
BME
ADDRESS
7
10
3
OUT
6
9
33
OUTPUTS
INPUTS
2
RESET
OUTPUTS 33 - 48
4
2A MAX
3
RESET
2
5
13
5
12
BME COMM
C
+
US
1
17
4
11
57
BME 1 (green)
1
3
10
20
64
OUTPUTS 1 - 16
17
2
9
17
OUTPUTS 17 - 32
OUTPUTS 49 - 64
53
ANAHEIM, CA
1
1
510
510
48
49
-
Computer
4
7
25
EXT
SYNC
C
3
6
32
33
59
2
5
24
41
58
OUTPUTS 33 - 48
1
16
20
31
35
38
IN
The matrix switchers covered in this manual are a family
of matrix switcher basic module enclosures (BMEs) that let
you create very large (up to 64 inputs and 64 outputs) matrix
switching systems for video, audio, or both. This family of
matrix switcher BMEs includes the following models:
19
57
About the Matrix Switchers
The Extron matrix switcher systems covered in this manual
distribute any input to any combination of outputs, routing
multiple input/output combinations simultaneously.
21
20
14
34
37
45
OUTPUTS 17 - 32
21
30
19
13
12
33
8
16
17
29
18
11
7
2A MAX
Connect to the built-in HTML pages, which you can use to
operate the switcher.
15
25
13
•
14
10
6
2A MAX
11
5
4
RESET
10
3
RESET
Load and start up the Windows®-based Matrix Switchers
Control Program
9
OUTPUTS
INPUTS
2
2A MAX
•
8
2A MAX
Perform basic operations and use both the front panel
controls and selected Simple Instruction Set (SIS™)
commands
4
7
1
This setup guide allows you to easily and quickly set up and
configure your matrix switcher system. This manual also shows
you how to:
•
3
6
13
OUTPUTS 1 - 16
OUTPUTS 33 - 48
2
5
RESET
OUTPUTS 1 - 16
1
BME COMM
About this Manual
BME 3 (horizontal)
ANAHEIM, CA
ANAHEIM, CA
+
US
IN
OUT
ACT LINK
C
LISTED
1T23
I.T.E.
US
Video and Sync In
Video and Sync Out
Audio In
Control
Audio Out
Crosspoint 450 Plus 6464 w/ Mav Plus 6464A
Figure 1-1 — Typical matrix switcher application
CrossPoint / MAV Matrix Switchers • Introduction
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
1-3
Introduction, cont’d
CrossPoint 450 Plus / MAV Plus Matrix Switchers
2
Chapter Two
Installation
Rear Panel Installation Features
Front Panel Configuration Port
1-4
CrossPoint / MAV Matrix Switchers • Introduction
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
Installation
3
*
N Extron recommends locking redundant front panel
1
controllers (if included in your system). See page 3-4.
ANAHEIM, CA
OUTPUTS 1 - 16
1
2
3
5
6
7
8
9
10
11
12
13
14
15
16
INPUTS
75
12345678
75
10 12 14 16
9 11 13 15
18
19
20
21
22
23
24
9
17
OUTPUTS 17 - 32
17
1
30
31
4
5
6
7
10
18
11
19
12
20
13
21
14
22
15
23
28
29
30
31
32
33
34
35
36
37
38
39
40
44
45
46
47
48
54
55
56
62
63
64
49
50
51
52
53
57
58
59
60
61
36
39
40
41
42
43
44
45
46
47
48
N Only sync BMEs have sync termination switches.
Only MAV Plus video BMEs have External Sync connectors.
N Smaller matrix sizes have fewer input connectors, output
connectors, or both.
2
OUTPUTS 49 - 64
28
32
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
Video and audio connections, sync termination,
and external sync
C Turn off power to the input and output devices, and
disconnect their power cords.
a
EXT
SYNC
BME COMM
BME
ADDRESS
LISTED
1T23
I.T.E.
** Sync BME only
●
●
MAV Plus video BME only
4
Tx
Rx
+
IN
2
LAN
4
Rx
US
REMOTE
-
Tx
C
11
35
38
24
27
43
34
37
16
26
42
33
8
2A MAX
29
27
3
25
41
26
2
510
510
25
Rear Panel Installation Features
OUTPUTS 33 - 48
4
10
ACT LINK
OUT
9 8
RESET
b
7
Figure 2-1 — Sync or video BME
5
c
Video inputs — Connect RGBHV, RGBS, RGsB, RsGsBs,
component/ HDTV video, S-video, or composite video sources,
as appropriate to your switcher system's video format and
matrix size.
Video outputs — Connect RGBHV, RGBS, RGsB, RsGsBs,
component/HDTV video, S-video, or composite video displays,
as appropriate to your switcher system's video format and
matrix size.
Sync termination switches (sync BMEs only) — Set the switches
as necessary to condition non-TTL sync levels greater than 5 Vp-p
for inputs 1 through 16 only. Sync termination enables the sync to
be properly passed from an input to the selected output(s).
510 ohms — The default position, suitable for most video.
75 ohms — Typically required only for an input with non-TTL
sync (greater than 5 V p-p).
N An input that produces an out of sync display, a display
that is rolling vertically and/or tearing horizontally, could
indicate a non-TTL sync input. If you are not sure, check
the specifications in the user’s manual for the input device.
7
10
d
External Sync (MAV Plus video BME) — If desired, attach an
external sync timing device to the external sync connector.
BLACK BURST/COLOR BAR
/AUDIO GENERATOR
POWER
C
12V
0.5A MAX
11
6
Figure 2-2 — Audio BME
2-2
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
EXT
SYNC
BBG 6 A
1 KHZ AUDIO
+4dBu
1
L
R
1
NTSC
8
9
3
5
4
6
Connect to
MAV Plus.
ON
1 2 3
-10dBV PAL
BLACKBURST/
COLORBAR
Extron BBG 6 A
2
Black Burst Color Bar
Audio Generator
BLACKBURST
OUT
Terminate cable
or connect to
another device.
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
2-3
Installation, cont’d
e
Audio inputs (audio BMEs) — Connect stereo or mono audio
sources to the 5-pole or 3-pole captive screw connectors.
Tip
Ring
Sleeve (s)
Tip
Ring
Unbalanced Stereo Input
R
Tip
Sleeve
L
Tip
Sleeve
Balanced Stereo Input
Do not tin the wires!
Computer or control system connection — Wire the
interface cable as a crossover cable.
Tip
Ring
Sleeve(s)
Tip
Ring
Unbalanced Stereo Output
in your system) and be the BME used for system control
and monitoring via the serial and Ethernet LAN ports.
i
BME address switch — Each BME must be set to a unique
address of 0 through 5 (addresses 6 through 9 are invalid).
R
Sleeve(s)
Tip
NO GROUND HERE.
Network connection — Wire as a patch (straight) cable.
N BME 0 should house the front panel controller (if included
Balanced Mono Input
L
Tip
•
•
BME connection and selection
Audio outputs (audio BMEs) — Connect stereo or mono audio
devices to the 5-pole or 3-pole captive screw connectors.
NO GROUND HERE.
LAN port — If desired, connect a network WAN or LAN hub, a
control system, or computer to the Ethernet RJ-45 port.
N The factory default IP address is 192.168.254.254.
Tip
Ring
Sleeves
f
h
Balanced Stereo Output
BME COMM
4
CAUTION For unbalanced stereo audio, connect the
sleeve(s) to the ground contact. DO NOT
connect the sleeve(s) to the negative (-) contacts.
Tip
Ring
Sleeves
Do not tin the wires!
Balanced Mono Output
Remote control connections
port — If desired, connect a control system or computer
g toRemote
the rear panel Remote RS-232/RS-422 port.
N Remote port defaults: RS-232, 9600 baud, no parity, 8-bit,
1 stop bit, no flow control.
1
5
Pin RS-232 Function RS-422 Function
1
— Not used
—
Not used
2
TX Transmit
TX– Transmit (–)
3
RX Receive
RX– Receive (–)
6
4
— Not used
—
Not used
5
Gnd Ground
Gnd Ground
9
6
— Not used
—
Not used
7
— Not used
RX+ Receive (+)
8
— Not used
TX+ Transmit (+)
9
— Not used
—
Not used
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
REMOTE
LAN
-
Tx
Rx
4
+
IN
ACT LINK
OUT
10
RESET
9 8
7
Sync BMEs cannot be set to address 0.
The addresses used in the system must be sequential with no
skipped numbers.
j
BME COMM interconnect ports — The BMEs in multiple BME
systems must be daisy-chained.
Connect an RJ-45 cable from BME 0’s BME Comm Out connector
to the nearest BME’s BME Comm In connector (usually BME 1).
M
BME COMM
OM
EC
BM
BME
ADDRESS
REMOTE
LAN
-
Tx
Tx
Rx
4
+
Rx
IN
ACT LINK
OUT
RESET
T
OU
IN
10
9
8
7
To Next BME
From Previous BME
2-4
BME
ADDRESS
Tx
Rx
Connect the next RJ-45 cable from BME 1's BME Comm Out
connector to the nearest unconnected BME’s BME Comm In
connector (usually BME 2).
Continue connecting RJ-45 cables from each daisy-chained
module’s BME Comm Out connector to the next module’s BME
Comm In connector until all modules are included in the chain.
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
2-5
Installation, cont’d
Power connection
k
Power — Plug the switcher into a grounded AC source.
Front Panel Configuration Port
I/O
CONTROL
VIEW
ESC
I/O CONFIG
VIDEO
AUDIO
POWER SUPPLY
PRIMARY
REDUNDANT
CROSSPOINT 450 PLUS SERIES
ULTRA WIDEBAND MATRIX SWITCHER
12
l
Configuration port — If desired, connect a control system
or computer to the front panel Configuration (RS-232) port.
Use an optional 9-pin D to 2.5 mm mini jack TRS RS-232
cable, part #70-335-01.
CrossPoint 450 Plus / MAV Plus Matrix Switchers
3
Chapter Three
Front Panel Operation
Creating a Tie
Saving or Recalling a Preset
Setting the Front Panel Locks (Executive Modes)
Viewing and Adjusting the Input Audio Level and Output Volume
Viewing Ties (and Muting Outputs)
2-6
CrossPoint / MAV Matrix Switchers • Installation
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
Front Panel Operation
1
2 3 4 5
5.
6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
I
N
P
U
T
S
Saving or Recalling a Preset
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
2 3 4 5
PRESET
VIEW
ESC
VIDEO
AUDIO
6 7 8 9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
O
U
T
P
U
T
S
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
1.
Save a preset — Press and hold the Preset button until it
flashes.
Recall a preset — Press and release the Preset button.
I/O
CONTROL
ENTER
1
Press and release the Enter button. All button indicators
turn off.
I/O CONFIG
Save a
preset
POWER SUPPLY
PRESET
PRIMARY
Press and hold.
Preset button blinks.
REDUNDANT
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Recall a
preset
PRESET
Press and release.
N The video selection button is labeled “RGBHV” on the
•
•
Creating a Tie
Press and release the Esc button to clear any button
indicators that may be lit.
2.
Press and release the RGBHV/Video and/or Audio I/O
button(s) to select or deselect video and/or audio as desired.
I/O
Green when selected.
Off when deselected.
Red when selected.
Off when deselected.
RGBHV AUDIO
3.
All input buttons with assigned
presets light.
The configuration data at assigned
preset locations will be overwritten.
1
2.
2
3
4
5
6
17 18 19 20 21 22
Press and release the desired input button.
The button blinks to indicate that this
preset is selected to save or recall.
N Audio or video can be broken away (tied by itself) by
selecting only the RGBHV/video button or only the
Audio button.
PRESET
Preset button lights.
CrossPoint 450 Plus switcher BMEs and “Video” on the
MAV Plus switcher BMEs.
1.
PRESET
2 seconds
3.
1
ENTER
The Enter button blinks to
indicate the need to
activate the save or recall.
Press and release the Enter button.
Press and release the desired input button.
The button lights to indicate the selection.
5
4.
Press and release the desired output button(s).
Amber indicates video and audio tie.
Green indicates video only tie.
Red indicates audio only tie.
3
3-2
4
8
ENTER
Green indicates the need
to confirm the change.
CrossPoint / MAV Matrix Switchers • Front Panel Operation
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Front Panel Operation
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
3-3
Front Panel Operation, cont’d
Setting the Front Panel Locks (Executive Modes)
The matrix switcher has three levels of front panel security lock
that limit the operation of the switcher from the front panel. The
three levels are:
•
Lock mode 0 — The front panel is completely unlocked.
•
Lock mode 1 — All changes are locked from the front
panel (except for setting Lock mode 2). Some functions
can be viewed.
•
Lock mode 2 — Basic functions are unlocked. Advanced
features are locked and can be viewed only.
Basic features consist of:
Selecting Lock mode 2 or toggling between
mode 2 and mode 1
N If the switcher is in Lock mode 0 or mode 1, this procedure
selects mode 2.
Toggle the lock on and off by pressing and holding the Video
button and the Audio button for approximately 2 seconds.
Press and hold
simultaneously.
I/O
m
Making ties
m Saving and recalling presets
m Setting input audio gain and attenuation
m Changing Lock modes
VIDEO
I/O
m
Setting video and audio output mutes
m Setting audio output volume
N For a complete list of advanced features, refer to the
CrossPoint 450 Plus / MAV Plus User’s Manual,
available on the Extron DVD or at www.extron.com.
Selecting Lock mode 2 or toggling between
mode 2 and mode 0
VIDEO
Toggle the lock on and off by pressing and holding the
Enter button, the Video button, and the Audio button for
approximately 2 seconds.
Press and hold simultaneously.
Viewing and Adjusting the Input Audio Level and
Output Volume
1.
VIDEO
AUDIO
Press and hold the Audio button until it flashes.
AUDIO
2 seconds
Press and
Hold
AUDIO
Audio button blinks.
2.
Press an input button (for input level) or output button
(for volume). Refer to the CrossPoint 450 Plus / MAV Plus
Switcher User's Manual, chapter 3, “Operation”, to read the
displayed value.
3.
Increase/decrease the level or volume by pressing the Esc
(>) and View (<) buttons.
4.
Press and release the Audio button to exit.
I/O
ENTER
AUDIO
The buttons blink twice.
Release the buttons.
N If the switcher is in Lock mode 0 or mode 1, this procedure
selects mode 2.
If the switcher is in Lock mode 2, this procedure selects
mode 0 (unlocks the switcher).
AUDIO
2 seconds
Advanced features consist of:
N The switcher is shipped from the factory in Lock mode 2.
If the switcher is in Lock mode 2, this procedure selects
mode 1.
2 seconds
I/O
ENTER
3-4
VIDEO
AUDIO
The buttons blink twice.
Release the buttons.
CrossPoint / MAV Matrix Switchers • Front Panel Operation
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Front Panel Operation
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
3-5
Front Panel Operation, cont’d
Viewing Ties (and Muting Outputs)
1.
Press the View button. Output buttons light for outputs
that have no ties established.
N If an output button blinks, that output is muted.
2.
Press an input button. The buttons for all tied outputs
light (amber for video and audio, green for video only, and
red for audio only).
3.
Press an output button. The buttons for the tied input and
all tied outputs light.
4.
If you want to toggle a mute on and off, press and hold
the output button for 2 seconds.
5.
Press the View button. All input and output buttons return
to an unlit state.
CrossPoint 450 Plus / MAV Plus Matrix Switchers
4
Chapter Four
Remote Control
Selected SIS Commands
Installing and Starting the Control Program
Accessing the HTML Pages
3-6
CrossPoint / MAV Matrix Switchers • Front Panel Operation
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
Remote Control
Selected SIS Commands
The switchers have Simple Instruction Set (SIS ) commands that
you can use for operation and configuration. You can run these
commands from a PC connected to either of the switcher’s serial
ports or the Ethernet port. See g (page 2-4), h (page 2-5), and
l (page 2-6), for connection information.
™
Establishing a network (Ethernet) connection
N If you connect to the switcher via the LAN port, and it
is the first time you have done so, you may change the
controller’s default settings (IP address, subnet mask,
and [optional] administrator name and password). See
"Configuring for Network Communication" for details.
Establish a network connection as follows:
1.
Open a TCP socket to port 23 using the switcher’s IP
address.
N The factory default IP address is 192.168.254.254.
The switcher responds with a copyright message including
the date, the name of the product, the firmware version,
the part number, and the current date/time.
N If the switcher is not password-protected, the device is now
ready to accept SIS commands.
N If the switcher is password-protected, a password
prompt appears.
2.
If the switcher is password protected, enter the appropriate
password.
If the password is accepted, the switcher responds with
Login User or Login Administrator.
If the password is not accepted, the Password prompt
reappears.
Number of connections
A switcher can have up to 200 simultaneous TCP connections,
including all HTTP sockets and Telnet connections. When
the connection limit is reached, the switcher accepts no new
connections until some have been closed. No error message or
indication is given that the connection limit has been reached.
To maximize performance of your switcher, the number of
connections should stay low and unnecessary open sockets
should be closed.
Verbose mode
Telnet connections to a switcher can be used to monitor
for changes that occur on the switcher, such as front panel
operations and SIS commands from other Telnet sockets or a
serial port. For a Telnet session to receive change notices from
the switcher, the Telnet session must be in verbose mode 3. See
the Verbose Mode command on page 4-9. In verbose mode 3,
the Telnet socket reports changes in messages that resemble SIS
command responses.
Host-to-switcher instructions
The switcher accepts SIS (Simple Instruction Set) commands
through either serial port. SIS commands consist of one or more
characters per command field. They do not require any special
characters to begin or end the command character sequence.
Each switcher response to an SIS command ends with a carriage
return and a line feed (CR/LF = ]), which signals the end of
the response character string. A string is one or more characters.
N The table that begins on the next page is a partial list
of SIS commands. For a complete listing, refer to the
CrossPoint 450 Plus / MAV Plus Switcher User's
Manual, chapter 4, “Programmer’s Guide”.
Connection timeouts
The Ethernet link times out and disconnects after a designated
period of time of no communications. By default, this timeout
value is set to five minutes but the value can be changed. See
the Set Connection Timeout command on page 4-9.
N Extron recommends leaving the default timeout at five
minutes and periodically issuing the Query (Q) command
to keep the connection active or disconnecting the socket
and reopening the connection when necessary.
4-2
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
4-3
ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Remote Control
Create ties
N • Commands can be entered back-to-back in a string, with no spaces. For example: 1*1!02*02&003*003%4*24$.
• The matrix switchers support 1-, 2-, and 3-digit numeric entries (1*1!, 02*02&, or 003*003%).
N When you create a tie where X! = 00, you tie no input to the specified output ([email protected]) (untie [email protected]).
When you create a tie where [email protected] = 00, you untie all outputs from input X!.
N The & tie command for RGB and the % tie command for video can be used interchangeably.
N The & read tie command for RGB and the % read tie command for video can be used interchangeably.
Tie input X! to output [email protected], video
and audio
Example:
X!*[email protected]!
[email protected]•InX!•All]
Tie input X!‘s video and audio to output [email protected]
1*3!
Out03•In01•All]
Tie input X! to output [email protected], RGBHV
Example
(see 3rd Note, above):
X!*[email protected]&
[email protected]•InX!•RGB]
Tie input 1 video and audio to output 3.
Tie RGB only (video breakaway).
10*4&
Out04•In10•RGB]
Tie input 10 RGB to output 4.
Tie input X! to output [email protected], video
Example
(see 3rd Note, above)
X!*[email protected]%
[email protected]•InX!•Vid]
Tie video only (video breakaway).
7*5%
Out05•In07•Vid]
Tie input 7 video to output 5.
Tie input X! to output [email protected], audio
Example:
X!*[email protected]$
[email protected]•InX!•Aud]
Tie audio only (audio breakaway).
24*04$
Out04•In24•Aud]
Tie input 24 audio to output 4.
Read RGB output tie
[email protected]&
[email protected]%
[email protected]$
X!]
X!]
X!]
RGBHV input X! is tied to output [email protected]
Read video output tie
Read audio output tie
N
X! = Input number
[email protected] = Output number
Command
Video input X! is tied to output [email protected]
Audio input X! is tied to output [email protected]
00 – (maximum number of inputs for your model) (00 = untie)
00 – (maximum number of outputs for your model) (00 = untie all outputs)
ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Video and audio mute commands
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
Read RGB/video mute
[email protected]*1B
[email protected]*0B
[email protected]
Global RGB/video mute
1*B
Global RGB/video unmute
0*B
Audio mute
Read audio mute
[email protected]*1Z
[email protected]*0Z
[email protected]
Global audio mute
1*Z
Global audio unmute
0*Z
View output mutes
EVM}
RGB/video mute
RGB/video unmute
Audio unmute
[email protected]*1]
Mute output [email protected] RGB (video off).
[email protected]*0]
Unmute output [email protected] RGB (video on).
1 = mute on, 0 = mute off.
X#]
Vmt1]
Vmt0]
[email protected]*1]
[email protected]*0]
X#]
Amt1]
Amt0]
X$1, X$2, ... X$n]
Mute all RGB outputs.
Unmute all RGB outputs.
Mute output [email protected] audio (audio off).
Unmute output [email protected] audio (audio on).
1 = mute on, 0 = mute off.
Mute all audio outputs.
Unmute all audio outputs.
Each X$ response is the mute status of an output,
starting from output 1.
n = the maximum number of outputs for this model.
Mut02202000000000000000000000000000]
Output 2, 3, and 5 audio is muted. All other
outputs are unmuted.
N The “Mut” portion of the response appears only when the switcher is in Verbose mode 3. See the Verbose mode command on page .
Example:
CrossPoint 450 Plus 6432 HVA
N
[email protected] = Output number
X# = Mute
X$ = Video/audio mute:
4-5
EVM}
01 – (maximum number of outputs for your model)
0 = off (unmuted)
1 = on (muted)
0 = no mutes
1 = video mute
2 = audio mute
Remote Control, cont’d
4-4
Command
ASCII command
Response
(host to switcher)
(switcher to host)
Set the audio volume to a specific
value
Example:
[email protected]*X%V
[email protected]•VolX%]
1*50v
Out01•Vol50]
Increment volume
[email protected]+V
[email protected]•VolX%]
Additional description
Audio output volume
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Remote Control
Example:
Decrement volume
Read output volume
1+V
Out01•Vol51]
[email protected]
[email protected]
[email protected]•VolX%]
Set output 1 volume to an X% value of 50, an
attenuation of 14 dB (79% of total volume).
Increase volume by 1 step.
Decrease volume by 1 step.
X%]
Save and recall presets
N • If you try to recall a preset that is not saved, the matrix switcher responds with the error code E11.
•The following characters are invalid in preset names: + - , ` @ = [ ] { } ‘ “ ; : | \ and ?.
Save current configuration as a
Command character is a comma.
SprX^]
X^,
global preset
Example:
Save current ties as preset 9.
Spr09]
9,
Recall a global preset
Example:
N
X^.
5.
[email protected] = Output number
X% = Volume
X^ = Preset number
Command
RprX^]
Command character is a period.
Rpr05]
Recall preset 5, which becomes the current
configuration.
01 – (maximum number of outputs for your model)
0 – 64 (1 dB/step except for 0-to-1, which is 22 dB) (default = 64 [0 dB])
00 - 64 (00 = current configuration, for viewing only)
ASCII command
(host to switcher)
Response
(switcher to host)
Additional description
Lock (executive) modes
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
N See “Setting the front panel locks (Executive modes)” on page 3-4 for more information on the Lock modes.
Lock all front panel functions
1X
Enable Lock mode 1.
Exe1]
Lock advanced front panel functions
2X
Exe2]
Enable Lock mode 2.
Unlock all front panel functions
0X
Exe0]
Enable Lock mode 0.
View lock status
X
X&]
N
X& = Lock mode
0, 1, or 2
Remote Control, cont’d
4-6
Command
4-7
ASCII command
Response
Additional description
(host to switcher)
(switcher to host)
I
VX*XX(•AX*XX([email protected]#]
Information requests
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Remote Control
Information request
VX*XX( = video size, AX*XX( = audio size,
[email protected] = BME type, UX1# = # of BMEs in system.
Example:
MAV 450 Plus 6448 with a
connected audio BME
This low resolution matrix switcher (T2) has 64 video
and 64 audio inputs by 48 video and 48 audio inputs.
This is a two BME system (a video and audio BME).
Request part number
N
Query controller firmware version
Q
Example:
N
V64X48•A64X48•T2•U2]
I
X1)]
X1!]
1.23]
Q
The factory-installed controller firmware version is
1.23 (sample value only).
X* = Inputs
Total number of inputs for this switcher
X( = Outputs
Total number of outputs for this switcher
X1) = Part number
See the CrossPoint 450 Plus / MAV Plus User’s Manual, for a complete list of part numbers.
X1! = Firmware version number to second decimal place (x.xx)
[email protected] = BME type
1 = wideband video
3 = sync
5 = mono audio
X1# = # of connected BMEs
Command
2 = low resolution video
1 through 6
ASCII command
4 = stereo audio
Response
(host to switcher)
(switcher to host)
EX1$CN}
ECN}
E•CN}
EX1%CI}
ECI}
EX1%CS}
ECS}
EX1%CG}
ECG}
EX1^DH}
EDH}
EX1&CV}
ECV}
E0*X1*TC}
E0TC}
E1*X1*TC}
E1TC}
Ipn•X1$]
X1$]
Ipn•X1$]
IpiX1%]
X1%]
IpsX1%]
X1%]
IpgX1%]
X1%]
IdhX1^]
X1^]
VrbX1&]
X1&]
Pti0*X1*]
X1*]
Pti1*X1*]
X1*]
Additional description
IP setup
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
Set matrix name
Read matrix name
Reset matrix name to factory default
Set IP address
Read IP address
Set subnet mask
Read subnet mask
Set gateway IP address
Read gateway IP address
Set DHCP on or off
Read DHCP on/off status
Set verbose mode
Read verbose mode
Configure current port timeout
Read current port timeout
Configure global IP port timeout
Read global IP port timeout
N
4-9
X1$ = Name
X1% = IP address
X1^ = DHCP
X1& = Verbose mode
X1* = Port timeout
Model name plus the last 3 pairs of the MAC address.
(Up to 240 alphanumeric characters)
###.###.###.###
0 = off
1 = on
0 = clear/none (default for Telnet connection) 2 = tagged responses for queries
1 = verbose mode (RS-232/RS-422 default)
3 = verbose mode and tagged for queries
1 (= 10 seconds) - 65000 (default is 30 = 300 seconds = 5 minutes)
Remote Control, cont’d
4-8
Command
Remote Control, cont’d
Installing and Starting the Control Program
4.
Another way to operate the switcher is via the Windows -based
Matrix Switchers Control Program. This program is contained
on the Extron Software Products DVD (included with the
switcher). Run this program on a PC connected to either of the
switcher’s serial ports or the Ethernet port. See g (page 2-4),
h (page 2-5), and l (page 2-6), for connection information. The
program must be installed on a Windows-based computer and
cannot be run from the DVD.
®
N For details on operating the program, refer to the
CrossPoint 450 Plus / MAV Plus Switcher User's
Manual, chapter 5, “Matrix Software”.
N If you connect to the switcher via the LAN port, and it is
the first time you have done so, you may need to change
the controller’s default settings (IP address, subnet mask,
and [optional] administrator name and password). See
"Configuring for Network Communication" for details.
Follow the on-screen instructions. The installation
program creates a C:\Program Files\Extron\
Matrix_Switchers directory and an “Extron Electronics\
Matrix Switchers” group folder. It installs the following
four programs:
•
•
•
•
MATRIX Switcher+ Control Program
MATRIX Switcher+ Help
Uninstall MATRIX Switcher
Check for Matrix Updates
Starting the program
1.
Click Start > Programs > Extron Electronics > Matrix
Switchers > MATRIX Switcher + Control Pgm.
The Comm Port Selection window appears.
Installing the program
1.
Insert the disk into the drive. The installation program
should start automatically.
The Extron software DVD window appears.
2.
Choose the comm (serial) port that is connected to the
switcher or IP [LAN].
N For a comm port, check the baud
rate displayed in the comm port
selection window. If you need to
change the baud rate, click the Baud
button and double-click the desired
baud rate.
N If the installation program does not self-start, run
Launch.exe from the DVD.
2.
Click the Software tab.
3.
Scroll to the Matrix Switchers program and click Install.
Click OK.
If you selected a serial port in step 2, the Matrix Switchers
Control Program is ready for operation.
4-10
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
4-11
Remote Control, cont’d
3.
If you selected IP [LAN] in step 2, the IP Connection
window appears.
Accessing the HTML Pages
Another way to operate the switcher is via its factory-installed
HTML pages, which are always available and cannot be erased
or overwritten. The switcher’s HTML pages are accessible
through its LAN port, connected via a LAN or WAN, using a
web browser such as Microsoft Internet Explorer. See h on
page 2-5, for connection information.
Configuring for Network Communication
a. Examine the Matrix IP Address field, which displays
the last Matrix IP address entered.
If necessary, enter the correct IP address in the field.
N 192.168.254.254 is the factory-specified default value for
this field.
b. If the switcher is password protected, enter the
appropriate administrator or user password in the
Password field.
c. Click Connect. The Matrix Switchers Control Program
is ready for operation.
The first time you connect a PC to a switcher BME via its LAN
port, you may need to temporarily change the PC’s IP settings
in order to communicate with the controller. Then you must
change the controller’s default settings (IP address, subnet
mask, and [optional] administrator name and password) in
order to use the unit on an intranet (LAN) or on the Internet.
After you have set up the CrossPoint or MAV switcher BME for
network communication, you can reset the PC to its original
network configuration.
N The computer and the switcher BME must both be
connected to the same subnet on a LAN (using a straightthrough cable). Alternatively, you can use a crossover
Ethernet cable to connect the controller directly to the
computer.
Use the ARP command to configure the IP address as follows:
1.
Obtain a valid IP address for the CrossPoint or MAV
switcher BME from the network administrator.
2.
Obtain the switcher BME’s MAC address (UID #) from the
label on its rear panel. The MAC address should have this
format: 00-05-A6-xx-xx-xx.
3.
If the switcher BME has never been configured and is
still set for factory defaults, go to step 4. If not, perform
a Mode 4 system reset. For detailed information
on reset modes, see “Rear Panel Operations” in the
CrossPoint 450 Plus / MAV Plus Switcher User's Manual.
N The switcher BME must be configured with the factory
default IP address (192.168.254.254) before the ARP
command is executed, as described below.
4.
4-12
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
At the PC, access the MS-DOS command prompt, then
enter the arp –s command. Type in the desired new
IP address for the unit (obtained in step 1) and the unit’s
MAC address (from the unit's rear panel). For example:
arp –s 10.13.197.7 00-05-A6-03-69-B0 and then
press {Enter}.
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
4-13
Remote Control, cont’d
After receiving the arp -s command, the controller
changes to the new address and starts responding to the
ping requests, as described in step 5.
Loading the start-up page
N If your Ethernet connection to the matrix switcher is
unstable, try turning off the proxy server in your Web
browser. In Microsoft Internet Explorer, click Tools >
Internet Options > Connections > LAN Settings,
uncheck the Use a proxy server... box, and then click
OK.
N You must ping the CrossPoint or MAV switcher BME as
shown in step 5 for the IP address change to take place. The
response should show the new IP address, as shown in the
following figure.
5.
Execute a ping command by entering “ping” followed by
a space and the new IP address at the command prompt.
For example:
ping 10.13.197.7
N For details on operating the switcher via HTML pages,
refer to the CrossPoint 450 Plus / MAV Plus Switcher
Manual, chapter 6, “HTML Operation”.
1.
Start the Web browser program.
2.
Click in the browser’s Address field.
C:\>ping 10.13.197.7
3.
Enter the Matrix IP address in the browser’s Address field.
Pinging 10.13.197.7 with 32 bytes of data:
N 192.168.254.254 is the factory-specified default value for
Reply
Reply
Reply
Reply
from
from
from
from
10.13.197.7:
10.13.197.7:
10.13.197.7:
10.13.197.7:
bytes=32
bytes=32
bytes=32
bytes=32
time<10ms
time<10ms
time<10ms
time<10ms
TTL=128
TTL=128
TTL=128
TTL=128
Ping statistics for 10.13.197.7:
Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
this field.
4.
Press the keyboard Enter key. The switcher checks to see if
it is password protected.
If the switcher is not password protected, it checks and
downloads the HTML start-up page. The switcher is ready
for operation via HTML remote control.
If the switcher is password protected, the switcher
downloads the Enter Network Password page.
N You can reconnect using either Telnet or a Web browser to
verify that the update was successful.
6.
After verifying that the IP address change was successful,
enter and issue the “arp –d” command at the DOS prompt.
For example:
arp –d 10.13.197.7 removes 10.13.197.7 from the ARP
table
or
arp –d* removes all static IP addresses from the ARP
table.
N A User name entry is not required.
4-14
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
5.
Enter the appropriate administrator or user password in
the Password field and click OK.
6.
The switcher downloads the HTML start-up page. The
switcher is ready for operation via HTML remote control.
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
4-15
Remote Control, cont’d
4-16
CrossPoint / MAV Matrix Switchers • Remote Control
Refer also to the CrossPoint 450 Plus / MAV Plus User’s Manual at www.extron.com.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement