VSP 729 User Manual
VSP 729
User Manual
 Manual #: RGB-RD-UM-V729 E001
 Revision: V1.2
VSP 729
User Manual
1
VSP 729·User Manual
Thank you for choosing our products!
In order to allow you to learn how to use the video processor quickly, we bring you
the detailed user‘s guide. You can read the introduction and directions before
using the video processor, please read all the information we provide carefully to
use our products correctly.
Copyright
©2012 All rights reserved by RGBLINK.
This document is done by Xiamen RGBlink Science & Technolog Co.,Ltd
independently. No part may be copied, reproduced or translated without
permission.
Notice
RGBlink provides this manual ―as is‖ without warranty of any kind, either
expressed or implied, including but not limited to the implied warranties or
merchantability and fitness for a particular purpose. RGBlink may make
improvements and/or changes to the product(s) and/or the program(s) described
in this publication at any time without notice.
This publication could contain technical inaccuracies or typographical errors.
Changes are periodically made to the information in this publication; these
changes are incorporated in new editions of this publication.
Federal Communications Commission (FCC)
Statement
This equipment has been tested and found to comply with the limits for a class A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area may cause
harmful interference, in which case the user will be responsible for correcting any
interference.
VSP 729
User Manual
2
Guarantee and Compensation
RGBlink provides a guarantee relating to perfect manufacturing as part of the
legally stipulated terms of guarantee. On receipt, the purchaser must
immediately inspect all delivered goods for damage incurred during transport,
as well as for material and manufacturing faults. RGBlink must be informed
immediately in writing of any complains.
The period of guarantee begins on the date of transfer of risks, in the case of
special systems and software on the date of commissioning, at latest 30 days after
the transfer of risks. In the event of justified notice of compliant, RGBlink can
repair the fault or provide a replacement at its own discretion within an appropriate
period. If this measure proves to be impossible or unsuccessful, the purchaser can
demand a reduction in the purchase price or cancellation of the contract. All other
claims, in particular those relating to compensation for direct or indirect damage,
and also damage attributed to the operation of software as well as to other service
provided by RGBlink, being a component of the system or independent service,
will be deemed invalid provided the damage is not proven to be attributed to the
absence of properties gurranteed in writing or due to the intent or gross
negligence or part of RGBlink.
If the purchaser or a third party carries out modifications or repairs on goods
delivered by RGBlink, or if the goods are handled incorrectly, in particular if the
systems are commissioned operated incorrectly or if, after the transfer of risks, the
goods are subject to influences not agreed upon in the contract, all guarantee
claims of the purchaser will be rendered invalid. Not included in the guarantee
coverage are system failures which are attributed to programs or special
electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well
as normal maintenance are not subject to the guarantee provided by RGBlink
either.
The environmental conditions as well as the servicing and maintenance
regulations specified in this manual must be complied with by the customer.
Trademarks
Brand and product names mentioned in this manual may be trademarks,
registered trademarks or copyrights of their respective holders. All brand and
product names mentioned in this manual serve as comments or examples and are
not to be understood as advertising for the products or their manufactures.
VSP 729
User Manual
3
Company address
RGBlink Science & Technology Co., Ltd.
Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial
Development Zone Xiamen, Fujian Province, P.R.C
Shenzhen office: Floor 11, A1 Building, Baiwang R&D Building,
Shahe West Road, Xili Town, Nanshan District, Shenzhen,
Guangdong Province, P.R.C
Beijing office:Room 410, Building 3, Dongyi International Business Park,
No.8 Gaojing Culture Garden, Chaoyang District, Beijing, P.R.C
Shanghai office:Building 3, 1358 Nong, Tongpu Road, Shanghai, P.R.C



~
~

Tel: +86-592-5771197
Fax:+86-592-5771202
Websites:
http://www.rgblink.com
http://www.rgblink.cn
E-mail:[email protected]
VSP 729
User Manual
4
Operators Safety Summary
The general safety information in this summary is for operating personnel.
Do Not Remove Covers or Panels
There are no user-serviceable parts within the unit. Removal of the top cover will
expose dangerous voltages. To avoid personal injury, do not remove the top
cover. Do not operate the unit without the cover installed.
Power Source
This product is intended to operate from a power source that will not apply more
than 230 volts rms between the supply conductors or between both supply
conductor and ground. A protective ground connection by way of grounding
conductor in the power cord is essential for safe operation.
Grounding the Product
This product is grounded through the grounding conductor of the power cord. To
avoid electrical shock, plug the power cord into a properly wired receptacle before
connecting to the product input or output terminals. A protective-ground
connection by way of the grounding conductor in the power cord is essential for
safe operation.
Use the Proper Power Cord
Use only the power cord and connector specified for your product. Use only a
power cord that is in good condition. Refer cord and connector changes to
qualified service personnel.
Use the Proper Fuse
To avoid fire hazard, use only the fuse having identical type, voltage rating, and
current rating characteristics. Refer fuse replacement to qualified service
personnel.
Do Not Operate in Explosive Atmospheres
To avoid explosion, do not operate this product in an explosive atmosphere.
VSP 729
User Manual
5
Terms In This Manual and Equipment
Marking
WARNING
Highlights an operating procedure, practice, condition, statement, etc,
which, if not strictly observed, could result in injury or death of
personnel.
Note
Highlights an essential operating procedure,
condition or statement.
CAUTION
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
VSP 729
User Manual
6
Change History
The table below lists the changes to the Video Processor User Manual.
Format
Time
ECO#
Description
Principal
V1.0
2011-12-08
0000#
Release
BIN
V1.1
2012-02-20
0001#
version upgrade
BIN
V1.2
2012-06-20
0002#
Renew address of Shenzhen
office
Add address of Beijing office
and Shanghai office
Renew format of specification
BIN
VSP 729
User Manual
7
CONTENT
CONTENT ............................................................................................. 8
1. Introduction ................................................................................... 15
Chapter Structure ........................................................................................ 16
How to Use This Guide ................................................................................ 17
Terms and Definitions .................................................................................. 18
System Overview ......................................................................................... 23
Application Questions.................................................................................. 24
2. Hardware Orientation .................................................................... 25
In This Chapter ............................................................................................ 25
VSP 729 Rear Panel ...................................................................................... 26
INPUT Interface ..................................................................................................... 26
1~4 9~11:CVBS Input .............................................................................................................................. 26
13.15.22.24:HDMI Input Interface.......................................................................................................... 27
14.16.23.25:VGA Input Interface ............................................................................................................ 27
17.21:USB Input Interface ...................................................................................................................... 27
19: Background Input Interface .............................................................................................................. 27
OUTPUT Interface ................................................................................................. 28
18:Preview Output Interface .................................................................................................................. 28
20:Program Output Interface ................................................................................................................. 28
CONTROL............................................................................................................... 28
5.Dial Switch ........................................................................................................................................... 28
6.10/100M Interface ............................................................................................................................... 28
7.USB Interface ....................................................................................................................................... 28
8.RS232 Interface.................................................................................................................................... 28
Switch and power ................................................................................................. 29
VSP 729
User Manual
8
26.Power................................................................................................................................................. 29
27.Switch Interface ................................................................................................................................. 29
VSP 729 Front Panel..................................................................................... 30
PROGRAM ............................................................................................................. 30
PREVIEW ............................................................................................................... 30
CUSTOM ................................................................................................................ 30
TRANSITION .......................................................................................................... 31
EFFECTS ................................................................................................................. 31
SAVE CONFIG ........................................................................................................ 31
Keyboard ............................................................................................................... 31
LCD Module .......................................................................................................... 31
Knob Switch .......................................................................................................... 31
VSP 729 Front Panel Keyboard Operation .................................................... 32
PROGRAM ............................................................................................................. 34
PREVIEW ............................................................................................................... 34
CUSTOM ................................................................................................................ 35
TRANSITION .......................................................................................................... 37
EFFECTS ................................................................................................................. 37
SAVE CONFIG ........................................................................................................ 38
KER BOARD ........................................................................................................... 39
Knob switch ........................................................................................................... 39
3. Hardware Installation ..................................................................... 40
In This Chapter ............................................................................................ 40
VSP 729
User Manual
9
Safety Precautions ....................................................................................... 41
Unpacking and Inspection ........................................................................... 41
Site Preparation........................................................................................... 41
4. Menu Orientation .......................................................................... 42
In This Chapter ............................................................................................ 42
PROG ........................................................................................................... 43
WIPE ............................................................................................................ 44
OUT ............................................................................................................. 46
SCALE .......................................................................................................... 47
MENU .......................................................................................................... 48
MENU---Dev Info................................................................................................... 49
MENU---Reset ....................................................................................................... 49
MENU---Matrix ..................................................................................................... 49
MENU---TP ............................................................................................................ 49
MENU---AB Mode ................................................................................................. 49
MENU---Crop ........................................................................................................ 50
MENU---Picture..................................................................................................... 50
MENU--- BG .......................................................................................................... 51
MENU--- Scale ....................................................................................................... 51
MENU--- Advance ................................................................................................. 52
MENU--- Time ....................................................................................................... 53
MENU--- Calendar ................................................................................................. 53
VSP 729
User Manual
10
MENU--- Language ................................................................................................ 53
MENU--- OUT ........................................................................................................ 53
5. Communication Software Guideline ............................................... 55
In This Chapter ............................................................................................ 55
Install Software ............................................................................................ 56
Run software ............................................................................................... 59
Set Up Communication ......................................................................................... 59
Input setting .......................................................................................................... 63
Input source choice .............................................................................................. 63
Input resolution .................................................................................................... 63
Display Mode ........................................................................................................ 63
Ration .................................................................................................................... 64
Image .................................................................................................................... 64
Background ........................................................................................................... 64
TP .......................................................................................................................... 65
Mode configuration .............................................................................................. 65
Image input ........................................................................................................... 65
Layer...................................................................................................................... 66
Screen Param ........................................................................................................ 66
Set ......................................................................................................................... 67
Save ....................................................................................................................... 67
Update reset ......................................................................................................... 67
VSP 729
User Manual
11
Mode control ........................................................................................................ 67
Preview ................................................................................................................. 68
Program ................................................................................................................ 68
Output resolution toolbar .................................................................................... 69
Current config mode ............................................................................................. 69
Switch mode ......................................................................................................... 69
Call saving modes ................................................................................................. 70
Switch output mode ............................................................................................. 70
CUT ........................................................................................................................ 71
Take ....................................................................................................................... 71
Effects Toolbar ...................................................................................................... 71
Fade duration ........................................................................................................ 72
Switch effect speed ............................................................................................... 72
Width of transparent toolbar ............................................................................... 72
Control .................................................................................................................. 72
Upgrade .................................................................................................................................................. 72
DVI DE Delay ........................................................................................................................................... 73
VGA Input Adjust .................................................................................................................................... 73
IP setting ................................................................................................................................................. 74
Factory reset ........................................................................................................................................... 74
Option ................................................................................................................... 74
Language ................................................................................................................................................ 74
Administration ...................................................................................................... 75
Advance Setting ...................................................................................................................................... 75
Help ....................................................................................................................... 75
Version notice ......................................................................................................................................... 75
About ...................................................................................................................................................... 75
VSP 729
User Manual
12
Information toolbar ................................................................................................................................ 75
How to control processor through RS232? .................................................. 76
How to control processor with console software by USB? ........................... 79
6. System Setup and Operations......................................................... 83
In This Chapter ............................................................................................ 83
Interface and Input Signal Option ................................................................ 84
The selection of signal format .............................................................................. 85
Single Image Switching ................................................................................ 86
Button Save User Mode Operations ..................................................................... 86
Single Image Switch .............................................................................................. 86
Size and Position setting ....................................................................................... 86
Background choice ...................................................................................... 88
Multiview image setting .............................................................................. 89
Size and position setting ....................................................................................... 89
Multiview image switching .......................................................................... 90
Multiview Matrix Function .......................................................................... 91
7. Common Questions and Solution ................................................... 92
In This Chapter ............................................................................................ 92
No Output in Large Screen ........................................................................... 93
Confirm if there are any input singles .................................................................. 93
Confirm if single output ........................................................................................ 93
Large Screen Output Flash Point .................................................................. 93
VSP 729
User Manual
13
Confirm if monitor output is normal .................................................................... 93
Large Screen only Display Part of the Image ................................................ 94
Signal need to scale .............................................................................................. 94
No Display in the Second Half Part of Large Screen ..................................... 94
Resolution is inadequate ...................................................................................... 94
Sending card can't take lower part ....................................................................... 94
Large Screen Shaking ................................................................................... 94
Sending card input recognition is not correct ...................................................... 94
Left of the Screen Appears Two Black Sides ................................................. 95
Adjust DE dethroughtion ...................................................................................... 95
All Key Lights Light Simultaneously .............................................................. 95
Check if dial switches are normal ......................................................................... 95
A.Specification ................................................................................... 96
B. Contact Information ....................................................................... 98
C. Upgrading Software ....................................................................... 99
VSP 729 upgrade firmware .......................................................................... 99
Download the IP software ......................................................................... 101
VSP 729
User Manual
14
1. Introduction
This chapter is designed to introduce you to the VSP 729 User Manual. Areas to
be covered are:

Chapter Structure

How to Use This Guide

Terms and Definitions

System Overview

Application Questions
VSP 729
User Manual
15
1. Introduction
Chapter Structure
Chapter Structure
The following chapters provide instructions for all aspects of VSP 729
operations.
Chapter 1
Introduction
Chapter 2
Hardware Orientation
Chapter 3
Hardware Installation
Chapter 4
Menu Orientation
Chapter 5
Communication Software Guidelines
Chapter 6
System Setup and Operations
Chapter 7
Common Questions and Solution
Appendix A Specification
Appendix B Contact information
Appendix C Upgrading Software
VSP 729
User Manual
16
1. Introduction
How to Use This Guide
How to Use This Guide
Following are important tips for streamlining your use of this User Manual in
its electronic ―PDF‖ form.
Navigating
Use Acrobat Reader‘s ―bookmarks‖ to navigate to the desired location.
All chapter files have the same bookmark structure for instant navigation
to any section. Please note:
 Extensive hyperlinks are provided within the chapters.
 Use Acrobat‘s ―Go to Previous View‖ and ―Return to next View‖
buttons to trace your complete navigational path.
 Use the ―Previous Page‖ and ―Next Page‖ buttons to go to the previous
or next page within a file.
 Use Acrobat‘s extensive search capabilities, such as the ―Find‖ tool
and ―Search Index‖ tool to perform comprehensive searches as required.
Table of Contents and Index
Use the Table of Contents bookmarks to navigate a desired topic.
Click any item to instantly jump to that section of the guide. You c
an also use the Index to jump to specific topics within a chapter. E
ach page number in the Index is a hyperlink.
General Operations
To ensure trouble-free operation, please follow all procedures as listed
below:
 For detailed installation instructions, refer to chapter 3 ―Hardware
Installation‖ on page 39.
 For communication software control guide, refer to Chapter 5,
―Communication Software Control Guide‖ on page 55.
 For system setup and operations, refer to Chapter 6, ―System Setup
and Operations‖ on page 83.
Should you have any questions regarding the installation or operation of
VSP 729, please consult with the factory. Refer to Appendix B on page 98
for contact information.
VSP 729
User Manual
17
1. Introduction
Terms and Definitions
Terms and Definitions
The following terms and definitions are used throughout this guide.
 “ASCII”: American Standard for Information Interchange. The standard
code consisting of 7-bit coded characters (8 bits including parity check)
used to exchange information between data processing systems, data
communication systems, and associated equipment. The ASCII set
contains control characters and graphic characters.
 “Aspect ratio”: The relationship of the horizontal dimension to the
vertical dimension of an image. In viewing screens, standard TV is 4:3,
or 1.33:1; HDTV is 16:9, or 1.78:1. Sometimes the ―:1‖ is implicit,
making TV = 1.33 and HDTV = 1.78.
 “AV”: Audio visual, or audio video.
 A “Background” is an unscaled source, typically originating from a
computer. Abackground source appears at the system‘s lowest priority
— visually in back of all other sources.
 “Baudrate”:Named of J.M.E. Baudot, the inventor of the Baudot
telegraph code. The number of the electrical oscillations per second,
called baud rate. Related to, but not the same as, transfer rate in bits
per second (bps).
 “Blackburst”: The video waveform without the video elements. It
includes the vertical sync, horizontal sync, and the chroma burst
information. Blackburst is used to synchronize video equipment to
align the video output. One signal is normally used to set up an entire
video system or facility. Sometimes it is called House sync.
 “BNC”: Bayonet Neill-Concelman. A cable connector used extensively
in television and named for its inventors. A cylindrical bayonet
connector that operates with a twist-locking motion. To make the
connection, align the two curved grooves in the collar of the male
connector with the two projections on the outside of the female collar,
push, and twist. This allows the connector to lock into place without
tools.
 “Brightness”: Usually refers to the amount or intensity of video light
produced on a screen without regard to color. Sometimes called ―black
level.
 ―CAT 5‖: Category 5. Describes the network cabling standard that
consists of four unshielded twisted pairs of copper wire terminated by
RJ-45 connectors. CAT 5 cabling supports data rates up to 100 Mbps.
CAT 5 is based on the EIA/TIA 568 Commercial Building
Telecommunications Wiring Standard.
 “Color bars”: A standard test pattern of several basic colors (white,
yellow, cyan, green, magenta, red, blue, and black) as a reference for
system alignment and testing. In NTSC video, the most commonly
used color bars are the SMPTE standard color bars. In PAL video, the
most commonly used color bars are eight full field bars. In the
computer, the most commonly used color bars are two rows of
reversed color bars.
 “Color burst”: In color TV systems, a burst of subcarrier frequency
located on the back porch of the composite video signal. This serves
as a color synchronizing signal to establish a frequency and phase
reference for the chroma signal. Color burst is 3.58 MHz for NTSC and
4.43 MHz for PAL.
 “Color temperature”: The color quality, expressed in degrees
Kelvin(K), of a light source. The higher the color temperature, the bluer
the light. The lower the temperature, the redder the light. Benchmark
VSP 729
User Manual
18
1. Introduction
Terms and Definitions










color temperature for the A/V industry include 5000°K, 6500°K, and
9000°K.
“Contrast ratio”: The radio of the high light output level divided by the
low light output level. In theory, the contrast radio of the television
system should be at least 100:1, if not 300:1. In reality, there are
several limitations. In the CRT, light from adjacent elements
contaminate the area of each element. Room ambient light will
contaminate the light emitted from the CRT. Well-controlled viewing
conditions should yield a practical contrast ratio of 30:1 to 50:1.
“DVI”: Digital Visual Interface. The digital video connectivity standard
that was developed by DDWG (Digital Display Work Group). This
connection standard offers two different connectors: one with 24 pins
that handles digital video signals only, and one with 29 pins that
handles both digital and analog video.
“EDID”: Extended Display Identification Data – EDID is a data structure
used to communicate video display information, including native
resolution and vertical interval refresh rate requirements, to a source
device. The source device will then output the optimal video format for
the display based on the provided EDID data, ensuring proper video
image quality. This communication takes place over the DDC – Display
Data Channel.
“Ethernet”: A Local Area Network (LAN) standard officially known as
IEEE 802.3. Ethernet and other LAN technologies are used for
interconnecting computers, printers, workstations, terminals, servers,
etc. within the same building or campus. Ethernet operates over
twisted pair and over coaxial cable at speeds starting at 10Mbps. For
LAN interconnectivity, Ethernet is physical link and data link protocol
reflecting the two lowest layers of the OSI Reference Model.
“Frame”: In interlaced video, a frame is one complete picture. A video
frame is made up of two fields, or two sets of interlaced lines. In a film,
a frame is one still picture of a series that makes up a motion picture.
“Gamma”: The light output of a CRT is not linear with respect to the
voltage input. The difference between what you should have and what
is actually output is known as gamma.
“HDMI” - High – Definition Multimedia Interface: An interface used
primarily in consumer electronics for the transmission of
uncompressed high definition video, up to 8 channels of audio, and
control signals, over a single cable. HDMI is the de facto standard for
HDTV displays, Blu-ray Disc players, and other HDTV electronics.
Introduced in 2003, the HDMI specification has gone through several
revisions.
“HDSDI”: The high-definition version of SDI specified in SMPTE-292M.
This signal standard transmits audio and video with 10 bit depth and
4:2:2 color quantization over a single coaxial cable with a data rate of
1.485 Gbit/second. Multiple video resolutions exists including
progressive 1280x720 and interlaced 1920x1080 resolution. Up to 32
audio signals are carried in the ancillary data.
“JPEG” (Joint photographic Expects Group): Commonly used
method of lossy compression for photographic images using a discreet
cosine transfer function. The degree of compression can be adjusted,
allowing a selectable tradeoff between storage size and image quality.
JPEG typically achieves 10:1 compression with little perceptible loss in
image quality. Produces blocking artifacts.
“MPEG”: Motion Picture Expect Group. A standard committee under
the auspices of the International Standards Organization working on
algorithm standards that allow digital compression, storage and
VSP 729
User Manual
19
1. Introduction
Terms and Definitions








transmission of moving image information such as motion video,
CD-quality audio, and control data at CD-ROM bandwidth. The MPEG
algorithm provides inter-frame compression of video images and can
have an effective compression rate of 100:1 to 200:1.
“NTSC”: The color video standard used in North America and some
other parts of the world created by the National Television Standards
Committee in the 1950s. A color signal must be compatible with
black-and-white TV sets. NTSC utilizes an interlaced video signals,
525 lines of resolution with a refresh rate of 60 fields per second (60
Hz). Each frame is comprised of two fields of 262.5 lines each, running
at an effective rate of 30 frames per second.
“PAL”: Phase Alternate Line. A television standard in which the phase
of the color carrier is alternated from line to line. It takes four full
pictures (8 fields) for the color-to-horizontal phase relationship to
return to the reference point. This alternation helps cancel out phase
errors. For this reason, the hue control is not needed on a PAL TV set.
PAL, in many transmission forms, is widely used in Western Europe,
Australia, Africa, the Middle East, and Micronesia. PAL uses 625-line,
50-filed (25 fps) composite color transmission system.
“Operator”: Refers to the person who uses the system.
“PIP”: Picture-in-Picture. A small picture within a larger picture created
by scaling down one of the images to make it smaller. Each picture
requires a separate video source such as a camera, VCR, or computer.
Other forms of PIP displays include Picture-by-Picture (PBP) and
Picture-with-Picture (PWP), which are commonly used with 16:9
aspect display devices. PBP and PWP image formats require a
separate scaler for each video window.
“Polarity”: The positive and negative orientation of a signal. Polarity
usually refers to the direction or a level with respect to a reference (e.g.
positive sync polarity means that sync occurs when the signal is going
in the positive direction).
“RJ-45”: Registered Jack-45. A connector similar to a telephone
connector that holds up to eight wires, used for connecting Ethernet
devices.
―RS-232”: An Electronic Industries Association (EIA) serial digital
interface standard specifying the characteristics of the communication
path between two devices using either DB-9 or DB-25 connectors.
This standard is used for relatively short-range communication and
does not specify balanced control lines. RS-232 is a serial control
standard with a set number of conductors, data rate, word length, and
type of connector to be used. The standard specifies component
connection standards with regard to the computer interface. It is also
called RS-232-C, which is the third version of the RS-232 standard,
and is functionally identical to the CCITT V.24 standard.
“Saturation”: Chroma, chroma gain. The intensity of the color, or the
extent to which a given color in any image is free from white. The less
white in a color, the truer the color or the greater its saturation. On a
display device, the color control adjusts the saturation. Not to be
VSP 729
User Manual
20
1. Introduction
Terms and Definitions








confused with the brightness, saturation is the amount of pigment in a
color, and not the intensity. Low saturation is like adding white to the
color. For example, a low-saturated red looks pink.
“Scaling”: A conversion of a video or computer graphic signal from a
starting resolution to a new resolution. Scaling from one resolution to
another is typically done to optimize the signal for input to an image
processor, transmission path or to improve its quality when presented
on a particular display.
“SDI”: Serial Digital Interface. The standard based on a 270 Mbps
transfer rate. This is a 10-bit, scrambled, polarity independent interface
with common scrambling for both component ITU-R 601 and
composite digital video and four channels of (embedded) digital audio.
“Seamless Switching”: A feature found on many video switchers. This
feature causes the switcher to wait until the vertical interval to switch.
This avoid a glitch (temporary scrambling) which normally is seen
when switching between sources.
“SMPTE”: Society of Motion Picture and Television Engineers. A global
organization, based in the United States, that sets standards for
baseband visual communications. This includes film as well as video
and television standards.
“S-video”: A composite video signal separated into the luma (―Y‖ is for
luma, or black and white information; brightness) and the chroma (―C‖
is an abbrethroughtion for chroma, or color information).
“Sync”: Synchronization. In video, sync is a means of controlling the
timing of an event with respect to other events. This is accomplished
with timing pulses to insure that each step in a process occurs at the
correct time. For example, horizontal sync determines exactly when to
begin each horizontal scan line. Vertical sync determines when the
image is to be refreshed to start a new field or frame. There are many
other types of sync in video system.(Also known as ―sync signal‖ or
―sync pulse.‖)
“TCP/IP”: Transmission Control Protocol/Internet Protocol. The
communication protocol of the Internet. Computers and devices with
direct access to the Internet are provided with a copy of the TCP/IP
program to allow them to send and receive information in an
understandable form.
“USB”: Universal Serial Bus. USB was developed by seven PC and
telecom industry leaders (Compaq, DEC, IBM, Intel, Microsoft, NEC,
and Northern Telecom). The goal was easy plug-and-play expansion
outside the box, requiring no additional circuit cards. Up to 127
external computer devices may be added through a USB hub, which
may be conveniently located in a keyboard or monitor. USB devices
can be attached or detached without removing computer power. The
VSP 729
User Manual
21
1. Introduction
Terms and Definitions




number of devices being designed for USB continues to grow, from
keyboards, mice, and printers to scanners, digital cameras, and ZIP
drives.
“VESA”: Video Electronics Standards Association. A nonprofit number
organization dedicated to facilitating and promoting personal computer
graphics through improved standards for the benefit of the end-user.
www.vesa.org
“VGA”: Video Graphics Array. Introduced by IBM in 1987, VGA is an
analog signal with TTL level separate horizontal and vertical sync. The
video outputs to a 15-pin HD connector and has a horizontal scan
frequency of 31.5 kHz and vertical frequency of 70 Hz (Mode 1, 2) and
60 Hz (Mode 3). The signal is non-interlaced in modes 1, 2, and 3 and
interlaced when using the 8514/A card (35.5 kHz, 86 Hz) in mode 4. It
has a pixel by line resolution of 640×480 with a color palette of 16 bits
and 256,000 colors.
“YCrCb”: Used to describe the color space for interlaced component
video.
“YPbPr”: Used to describe the color space for progressive-scan
(non-interlaced) component video.
VSP 729
User Manual
22
1. Introduction
System Overview
System Overview
VSP 729 is a seamless switcher that accepts a wide variety of video
signals, including CVBS、YPbPr、computer RGBHV(VGA), DVI-D、HDMI、
HDTV. It combines truly seamless, glitch-free switching with advanced
scaling technologies to meet the requirements of high quality, high
resolution video presentations.With presentation-enhancing features
such as independent Preview and Program outputs, numerous switching
transition effects, multi windows operation up to 5 windows, 4
predefinition modes configuration,multiple user modes, internal test
patterns, and multiple control methods, the VSP 729 is designed to deliver
advanced capabilities to high-end presentation environments.
VSP 729 is ideal for stage, corporate boardrooms, auditoriums,
houses of worship and other live events. Full setup and operation is
available from the front panel as well as through RS-232 and Ethernet
control. Furthermore, presentations can be managed using the RGBlink
CP 1024 Remote Control Panel.
VSP 729
User Manual
23
1. Introduction
Application Question
Application Questions
RGBlink offers solutions to demanding technical problems. Any application
questions, or required further information, please contact with our
Customer Support Engineers. Refer to Appendix B for contact details.
VSP 729
User Manual
24
2. Hardware Orientation
In This Chapter
This chapter provides detailed information about the VSP 729 hardware.
The following topics are discussed:

VSP 729 Rear Panel

VSP 729 Front Panel

VSP 729 Front Panel Keyboard Operation
VSP 729
User Manual
25
2.Hardware Orientation
VSP 729 Rear Panel
VSP 729 Rear Panel
The figure below illustrates the professional interface and control signals
of VSP 729 rear panel.
NO
INTERFACE
NO
INTERFACE
1~4.9~12
CVBS input
14.16.23.25
VGA Input
5
Dial Switch
17.21
USB Input
6
10/100M Interface
18
Preview Input
7
USB Interface
19
Background Input
8
RS232 Interface
20
Program Input
13.15.22.24
HDMI Input
26.27
Switch and power
INPUT Interface
1) 8 CVBS inputs by BNC interfaces, 1 SVideo input;
2) 4 VGA input by DB15 interface. 4 DVI-I interface, can be compatible
with HDMI inputs;
3) 4 USB inputs
3) 1 Background input
1~4 9~11:CVBS Input
CVBS input. Can receive standard video signal from players, cameras etc.
Input supported resolution 480i and 576i through BNC. Supported
standards include: PAL, NTSC and SECAM.
VSP 729
User Manual
26
2.Hardware Orientation
VSP 729 Rear Panel
13.15.22.24:HDMI Input Interface
HDMI 1/2/3/4 input interface. Support HD Player、DVD、computer video
signals, support resolution:SMPTE:625/25/50 PAL, 525/29.97/59.94
NTSC, 1080P50, 1080P59.94/60,
1080i50,1080i59.94/60, 720p50,720p59.94/60;
VESA:800×600×60Hz,1024×768×60Hz,1280×768×60Hz,
1280×1024×60Hz,1600×1200×60Hz,1920×1080×60Hz;
Note
HDMI1~4 :standard DVI-I interface,compatible
HDMI;
14.16.23.25:VGA Input Interface
VGA 1/2/3/4 input interface, support HD Player 、 computer video
signals .compatible YPbPr signals through DB9 interface ; support
resolution:
VGA-UXGA
:800×600×60
Hz,
1024×768×60
Hz,
1280×1024×60 Hz,
1440×900×60 Hz,1600×1200×60 Hz;
17.21:USB Input Interface
USB 1/2/3/4 interface;Used to connect the computer. Used to connect
with external USB disk, to play the media files inside that.
19: Background Input Interface
Background input interface.support HD Player、computer video player
signals through DVI-I interface. Accept DVI signals through DVI directly
with
the
input resolution : 800×600×60Hz , 1024×768×60Hz ,
1280×768×60Hz,1600×1200×60Hz,1920×1080×60Hz;
VSP 729
User Manual
27
2.Hardware Orientation
VSP 729 Rear Panel
Note
Back ground resolution should be the same to
the set up output resolution.
OUTPUT Interface
18:Preview Output Interface
All VSP 729 outputs can be programmed as preview output, DVI and VGA
outputs are set as preview in default.
Note
VGA output: VGA output is also go by DVI-I
interface, by a DVI to VGA adaptor or a DVI to
DVI+VGA split cable.
Support resolution:VESA:1024×768×60Hz,
20:Program Output Interface
Program output interface can connect with next displayer or send signal to
LED through sending card. Output signals through DVI-I.
Support resolution:VESA:1024×768×60Hz,1280×768×60Hz,1600×
1200×60Hz,1920×1080×60Hz.
CONTROL
5.Dial Switch
6.10/100M Interface
7.USB Interface
Use to connect the computer;
8.RS232 Interface
Use to connect the computer;
VSP 729
User Manual
28
2.Hardware Orientation
VSP 729 Rear Panel
Switch and power
26.Power
AC 90-264V 3.8A 50/60Hz IEC-3 Switch interface
27.Switch Interface
VSP 729
User Manual
29
2.Hardware Orientation
VSP 729 Front Panel
VSP 729 Front Panel
编号
编号
1
PROGRAM
6
SAVE CONFIG
2
PREVIEW
7
Keyboard
3
CUSTOM
8
LCD Module
4
TRANSITION
9
Knob Switch
5
EFFECTS
PROGRAM
VSP 729 supports five display layers, four of them is programmable inputs,
the 5th one is background input;More details please refer to:
PROGRAM .
PREVIEW
Program and choice signal source through preview 1234 and PRO.And
preview on the back panel.All program finished at the preview;More details
please refer to:PREVIEW .
CUSTOM
Compile signal,effects configuration,save,out format selection,scaling
seting;More details please refer to:CUSTOM.
VSP 729
User Manual
30
2.Hardware Orientation
VSP 729 Front Panel
TRANSITION
Seamless cutting and seamless dissolving;More details please refer to:
TRANSITION.
EFFECTS
Single image,dual image,three image,four image;More details please refer
to:EFFECTS.
SAVE CONFIG
Parameter recalling;More details please refer to:SAVE CONFIG.
Keyboard
NEXT: push to confirm the current choice;
MENU: push to go to main menu or exit from current choice item.;
More details please refer to:keyboard
LCD Module
More details please refer to:LCD Module
Knob Switch
Running up and down,choose the menu of LCD;More details please refer
to :Knob switch
VSP 729
User Manual
31
2.Hardware Orientation
VSP 729 Front Panel Keyboard Operation
VSP 729 Front Panel Keyboard Operation
Insert power cord and push power to ON position. LCD module on the front
panel will show RGBLINK and go into self verification before it load last
setting config and send processed image to the target monitor. For the first
setup, CV1 input is default source. With front panel keyboard, user can
operate VSP 729 through the menus on LCD panel.
RGBLINK
VSP729 front panel as shown in figure::
AVDSP Series VSP 729
Wait Init Network…
Finish Network!
VSP 729 can be connect to the LAN through network
DHCP Failed
Cable,if the connection can not Find the LAN ,
it will show DHCP Failed
If connection to the LAN works,it will get a
Auto config IP address.Shown as following
VSP 729
User Manual
IP Address
192.168.0.100
32
2.Hardware Orientation
VSP 729 Front Panel Keyboard Operation
In to the cycle:
When in to the cycle ,it shows:the current input format,preview,the current
output format,the current software information,the current device serial
number.User have the device serial number will acquire more effective
service and support.
5 SEC
5 SEC
Program 1:CV1
720 x 576x50i
Preview 1:CV1
720 x 576x50i
5 SEC
5 SEC
RGBlink
SN:CM0024
Output Format:
1024x768x60
5 SEC
Software Version
0.17
VSP 729
User Manual
33
2.Hardware Orientation
VSP 729 Front Panel Keyboard Operation
PROGRAM
1:Channel 1,program input,Pressping this button can't work,lighting button is
the signal on display.
2:Channel 2,program input,Pressping this button can't work,lighting button is
the signal on display.
3:Channel 3,program input,Pressping this button can't work,lighting button is
the signal on display.
4:Channel 4,program input,Pressping this button can't work,lighting button is
the signal on display.
5:Channel,program input,Pressping this button can't work,lighting button is the
signal on display.
Pressping 1-4,LCD module will show as following(select1)
:
Program 1:CV1
720x576x50i
Pressping5,LCD module will show as following:
Program 5:
Black
l
PREVIEW
VSP 729
User Manual
34
2.Hardware Orientation
VSP 729 Front Panel Keyboard Operation
1:Channel 1,program input,Pressing to switch to preview output
2:Channel 2,program input,Pressing to switch to preview output
3:Channel 3,program input,Pressing to switch to preview output
4:Channel 4,program input,Pressing to switch to preview output
5:Channel,program input,Pressing to switch to preview output
Pressping1-4,LCD module will show as following(select1)
:
Preview 1:CV1
720x576x50i
Pressping5,LCD module will show as following:
Preview 5:
Black
CUSTOM
l
Select channel, Pressing this button to program the input source,
HDMI、DVI、VGA、YPbPr,CVBS1,CVBS2,CH1,CH2,CH3,
CH4(matrix).
Pressing the button to enter Effects Configuration Menu,multiples effects
are available, such as Wipe hard,Wipe Plus out.
Pressing the button to enter fade in fade out configuration menu,users can
set the duration time of fade effect.The duration time of fade:0.5~30S.
Dissolve Duration
>1.5S(0.5~30S)
VSP 729
User Manual
35
2.Hardware Orientation
VSP 729 Front Panel Keyboard Operation
Pressing to ready to save user customize configuration: SAVE CONFIG 1、2、
3、4、5、6.Pressping SAVE CONFIG 1、2、3、4、5、6 to recall the saving
parameters;
Save Setting to:
Press Menu To Exit
Save Setting to:
SAVE1
Finished!l
SAVE CONFIG 1、2、3、4、5、6,select mode,such as 1:
Out format selection, Pressing this button inter into current format, select
the format through rotary switch,VSP 729 support four output resolution,
More details please refer to OUT;
Pressing to go to scaling setting,under PIP can set sub-main image size
and position;
Note
Scaling is only valid for the program output,while
preview image keeps full screen.Scale is only
enable when user select the same layer under
Preview and Program.
User can change the screen size and position through change numeric
parameters.Apply to LED user.
VSP 729
User Manual
36
2.Hardware Orientation
VSP 729 Front Panel Keyboard Operation
TRANSITION
Seamless cutting button,press the button to switch preview out to
Program Output;
Cut to 3:
Seamless dissolving ,press the button to switch preview out to Program
Output with dissolving transition effect.
Take to 3:
EFFECTS
Pressing to make single image ;
Setup Single Mode:
Finished!
Pressing to make dual-image;
Setup PIP Mode:
Finished!
VSP 729
User Manual
37
2.Hardware Orientation
VSP 729 Front Panel Keyboard Operation
Pressing to make three image;
Setup 3PBP Mode:
Finished!
Pressing to make three image
Setup 4PBP Mode:
Finished!
SAVE CONFIG
1: Save1,Pressping the button to recall the saving parameters;
2: Save 2,Pressping the button to recall the saving parameters;
3: Save 3,Pressping the button to recall the saving parameters;
4: Save 4,Pressping the button to recall the saving parameters ;
5: Save 5,Pressping the button to recall the saving parameters;
6: Save 6,Pressping the button to recall the saving parameters;
Load Setting From:
SVEV1
Finished!
VSP 729
User Manual
38
2.Hardware Orientation
VSP 729 Front Panel Keyboard Operation
KER BOARD
Menu:push to go to main menu or exit from current choice item;
Next:push to confirm the current choice.
Knob switch
Running up and down,select the menu of LCD.
VSP 729
User Manual
39
3. Hardware Installation
In This Chapter
This chapter provides comprehensive installation instruction for VSP 729
hardware:
Following is the size of VSP 729 for your reference.
VSP 729
User Manual
40
Safety Precautions
For all VSP 729 processor installation procedures, please observe the
following important safety and handling rules to avoid damage to yourself
and the equipment.
 To protect users from electric shock, ensure that the chassis connects
to earth through the ground wire provided in the AC power Cord.
 The AC Socket-outlet should be installed near the equipment and be
easily accessible.
Unpacking and Inspection
Before opening VSP 729 process shipping box, inspect it for damage. If
you find any damage, notify the shipping carrier immediately for all claims
adjustments. As you open the box, compare its contents against the
packing slip. If you find any shortages, contact your sales representative.
Once you have removed all the components from their packaging and
checked that all the listed components are present, visually inspect the
system to ensure there was no damage during shipping. If there is damage,
notify the shipping carrier immediately for all claims adjustments.
Site Preparation
The environment in which you install your VSP 729 should be clean,
properly lit, free from static, and have adequate power, ventilation, and
space for all components.
VSP 729
User Manual
41
4. Menu Orientation
In This Chapter
This chapter describes all VSP 729 processor menus, including how they
are accessed, the functions that are available, and descriptions of each
menu tree (in block diagram format).
The following topics are discussed:
• PROG
• WIPE
• OUT
• SCALE
• MENU
• MENU
VSP 729

Dev Info

Reset

Matrix

TP

AB Mode

Crop

Picture

BG

Scale

Advance

Time

Calendar

Language

OUT
User Manual
42
4.Menu Orientation
PROG
PROG
Select channel,Pressping this button to program the input source,
HDMI、DVI、VGA、YPbPr,CVBS1,CVBS2,CH1,CH2,CH3,
CH4(matrix) .
Pressping the Preview,and Pressping PROG,rotate the knob switch to
show tree diagram on the LCD.User can select by need to.Preview5 in to
set background,User can select Black or VINO.
VSP 729
User Manual
43
4.Menu Orientation
WIPE
WIPE
Press the button to enter Effects Configuration Menu, multiples effects are
available are available.
VSP 729
User Manual
44
4.Menu Orientation
WIPE
VSP 729
User Manual
45
4.Menu Orientation
OUT
OUT
Out format selection, Pressping this button enter into current format,
change the format through rotary switch.
VSP 729 support four output format;s following:
VSP 729
User Manual
46
4.Menu Orientation
SCALE
SCALE
Pressping to go to scaling setting,under PIP can set sub-main image size
and position;
Note
Scaling is only valid for the program output,while
preview image keeps full screen.Scale is only
enable when user select the same layer under
Preview and Program.
User can change the screen size and position through change numeric
parameters.Apply to LED user.
VSP 729
User Manual
47
4.Menu Orientation
MENU
MENU
push to go to main menu or exit from current choice item.
Pressping to enter to system menu .System menu will show as following:
button to select the left or right menu. Before the menu item,
if there is a * sign, means the menu item has been selected.
VSP 729
User Manual
48
4.Menu Orientation
MENU
MENU---Dev Info
Select Dev Info ,Pressing NEXT ,It will show the information of input and
output video signals.As picture above ,running the knob switch can check
preview output format,output format, program version,the current in marsat
seria number.
MENU---Reset
elect Reset,Pressping NEXT to previously saved user-mode will be
clear;and it will show as picture above.
MENU---Matrix
Pressping Menu to go back main menu and use the Knob button and Next
to go into Crop setting sub menu.Select Matrix and Pressping Next to go
into Matrix,menu including:
Matrix:Can save other any channel in channel 1.Such as the red display
above.Motioned for: the channel 2 signal copy to channel 1,The orange
display motioned for:the channel 3 signal copy to channel 2.
MENU---TP
Pressping Menu to go back main menu and use the Knob button and Next
to go into Crop setting sub menu .Select TP and Pressping menu.Menu
including:Pressping Next to go into Program .User can select OFF or
ON.The same operation can be set Preview TP.
Note
TP farm is Color Bar,Resolution: 1024x768x60.
MENU---AB Mode
Pressping Menu to go back main menu and use the Knob button and Next
to go into Crop setting sub menu .【AB Mode】:Full screen switch,Full
screen transparent switch,Opening ceremony switch,Opening ceremony
VSP 729
User Manual
49
4.Menu Orientation
MENU
transparent switch But also other fourteen seamless transition effects: wipe
right ,wipe left ,wipe up,wipe down, wipe center out, wipe curtain out ,wipe
square out etc.
Running knob switch and select AB Mode ;Stretching including: CUT
Switch wipe right, wipe left ,wipe up,wipe down, wipe center out, wipe
curtain out ,wipe square out etc.And DISSOVLE Switch
Setup AB Mode:
>Dissolve Switch
Setup AB Mode:
>Wipe HARD Switch
Setup AB Mode:
>Wipe SOFT Switch
Setup AB Mode:
>CUT Switch
MENU---Crop
Pressping Menu to go back main menu and use the Knob button and Next
to go into Crop setting sub menu to go into Crop:
Crop Width;
Crop Height;
Crop Pos X;
Crop Pos Y;
MENU---Picture
Pressping Menu to go back main menu and use the Knob button and Next
to go into Crop setting sub menu to go into Picture:
Set Brightness:To change the brightness value of image;
VSP 729
User Manual
50
4.Menu Orientation
MENU
Set Contrast:To change the contrast value of image;
Set Saturation:To change the saturation value of image;
Set Color Red :To change the red color value of image;
Set Color Green:To change the green color value of image;
Set Color Blue:To change the blue color value of image;
Users can adjust the settings according to the actual situation, this
function is mainly applied to the technician who is very professional at the
image quality.However, if there is any improper operation and image
quality errors or distortion occur, reset the device from main menu Recall.
MENU--- BG
Pressping Menu to go back main menu and use the Knob button and Next
to go into Crop setting sub menu to go into BG:Running knob can select
BG,Black is Background,VeI NO is the input Background.
Note
Background input picture resolution is the same
as output resolution;
MENU--- Scale
Pressping Menu to go back main menu and use the Knob button and Next
to go into Crop setting sub menu to go into Scale:
Scale Width;
Scale Height;
Scale Pos X;
Scale Pos Y;
Enable:The channel switch.If select OFF,the channel will be closed,and
will blank screen when switchover.
Note
The same operation can be set Scale.
VSP 729
User Manual
51
4.Menu Orientation
MENU
MENU--- Advance
Pressping Menu to go back main menu and use the Knob button and Next
to go into Crop setting sub menu to go into Advance:
Pressping NEXT to go into Screen as picture above:
Screen Width;
Screen Height;
Screen Pos X;
Screen Pos Y;
Can realize the narrowing of the signal and the full screen switch.
Knob the switch select Others,and Press NEXT to enter other set.And
There are Aspect Ratio Normal ratios are 4:3 and 16:9,spin the knob to
realize the convertion between the two types.
Knob the switch to select Swap or Stay.If select Swap then Press
CUT/TAKE can realize between the Program and Preview.If select Stay the
Program will turn to channel2.Preview will stay channel 2.As following:
Preview Switch:
*Swap
Preview Switch:
*Stay
Knob the switch and select Swap PROG PRE,also select Swap or Normal
to realize the convertion between (Swap) and (Normal) of Preview and
Program.As following:
Swap PROG PRE:
*Swap
Swap PROG PRE:
*Swap
VSP 729
User Manual
52
4.Menu Orientation
MENU
Select Output Format, details funtions is the same as OUT
Output Format:
>1024X768X60
MENU--- Time
Press MUNU , return to the main menu ,knob the switch to set Time.Press
NEXT to enter Time setting;Press NEXT to activate the Time setting,if
there is a * sign ,means the menu item has been selected;spin the knob
from the front keyboard to revise the time.
MENU--- Calendar
Press MUNU , return to the main menu ,knob the switch to set Calendar;
Press NEXT to enter Calendar setting;Date shows on the left side,Day
shows on the right side;Press NEXT to activate the Calendar setting, if
there is a * sign, means the
menu item has been selected,Knob the switch to change the value;
MENU--- Language
Press MUNU , return to the main menu ,knob the switch to set
Language;Knob the switch to inter Language setting;Press NEXT to
set.Inter the corresponding sub-menu settings; go to program sub-menu as
shown:To select the LED language in English or Chinese.
MENU--- OUT
Press MENU , return to the main menu;Press MENU and select OUT to set
DE and choice output format(HDMI or DVI)
Select Program Press NEXT to inter the corresponding sub-menu
settings;Firstly setting DE Setup;Select ON and Press NEXT to inter DE
setting.
DE H Start;
DE V Star;
VSP 729
User Manual
53
4.Menu Orientation
MENU
DE Width;
DE Height;
When signal work on the display,the side of display show black,Use this
setting to make the full-screen.Select Program Press NEXT to select the
output interface HDMI/DVI.Normal interface is DVI,Select HDMI when need
to HDMI.The same way can set Preview.
VSP 729
User Manual
54
5. Communication Software Guideline
In This Chapter
This chapter provides detailed information about the control
communication software. The following topics are discussed:

Install Software

Run Software

How to control processor through RS232?

How to control processor with console software by USB?
VSP 729
User Manual
55
5. Communication Software Guideline
Install Software
Install Software
AVDSP video processor is very easy to be configured with user friendly
communication software, support drag and drop operation for edit and
display.Also it can be customized with schedule function.
Double click
to install, English version default for use, click
―select‖ to next dialog:
And in next dialog is the user agreement of the software, click Agree to go
on:
VSP 729
User Manual
56
5. Communication Software Guideline
Install Software
User can select ―Change‖ to choose the VSP 729 install software:
Click ―Next‖ to go on:
Click ―Next‖ to go on:
VSP 729
User Manual
57
5. Communication Software Guideline
Install Software
Click ―Next‖ to go on:
Click ―Finish‖ and ready to run VSP729 console:
VSP 729
User Manual
58
5.Communication Software Guideline
Run software
Run software
Install communication which comes with the package of VSP 729 device.
Double click
Double click
icon from home screen to run the software.
icon from home screen to run the software.
VSP 729 communication software interface as shown:
Set Up Communication
Use VSP 729 there are power line ,three line of control,one reticle.one
USB line,one RS-232,one DB9F,and one 6B4C.
Below are the detail about connection steps:
Set up DB9F to the correspondence interface on the computer.And set up
COM to the RS232.Open the video processor;Next to the operation of a
computer ,back to the desktop window,the right button click on the "my
computer",find―hardware‖As show,the left button click on the device
manager.
VSP 729
User Manual
59
5.Communication Software Guideline
Run software
Find COM and LPT,click the "+" on the left,Record the name of serial port
the computer provide.As show ,the serial port is COM6
Open the control software after select the serial port.Find SET UP ,click to
enter setup option:
VSP 729
User Manual
60
5.Communication Software Guideline
Run software
Serial is the default COM, click icon
to refresh COM number,
choose
available COM,default Baudrate is 115200.After serial setting, click
icon,The icon becomes
when successfully connected,on the left
bottom showing
Note
RS 232 can be 100M upgrade, USB line shall
not do this upgrade.
VSP 729
User Manual
61
5.Communication Software Guideline
Run software
Ethernet: user can fill any number less than 1023 in Local Port. The
Remote Port must be 192.168.0.100 and the Remote Port must be 1000.
After setting above, click the icon
to connect with network.If
successfully connected, the icon
becomes
,Status on the left bottom showing
Mode configuration:
User need to set output after set up communication.Configuration and
Input Configuration is the same as PROG.If has the key programming,can
ignore this operation.Detail More details please refer to:PROG.
VSP 729
User Manual
62
5.Communication Software Guideline
Run software
Input setting
setting:Configurate Input information ,can configurate for Input 1,Input 2,
Input 3,Input 4,Input 5 separately.
Input source choice
CV,YPbPr,VGA,DVI input sources.
According to the actual input signal source edit definition.
Note
the same as PROG function.
Input resolution
Shows the resolution of current input source.Just for inquiry,not operation.
Display Mode
offers 2 different display modes, when selected ―live video ―,video will be
played normally, when selected ―freeze‖ the display only shows the last
frame.
VSP 729
User Manual
63
5.Communication Software Guideline
Run software
Ration
User can choose 4:3 or16:9 from scrolling down list;
Image
Can set the brightness of the image, color temperature, contrast and
saturation, sharpening
Note
The set is the same as Picture.
Background
Background can be set as black color black-field or VINO video signal
input.(When setting VIN0 as video input; make sure that the resolution of
background is the same as output resolution.)
VSP 729
User Manual
64
5.Communication Software Guideline
Run software
Note
The set is the same as BG.
TP
Test pattern image is color toolbar , with resolution
1024x768x60,both preview and program can be set.
Note
The set is the same as TP.
Mode configuration
Image input
VSP 729 is a multi-layer processor,the data of each layer can be set from
this toolbar. Dates can be input at any combination, i.e.,the four different
layers can be configurated by the same channel or by the 4 totally
different channels. That is what call ― Matrix Function‖. Scale , Zoom ,Crop
can be realized by entering the value or rolling down the list, or drag and
drop the picture .
VSP 729
User Manual
65
5.Communication Software Guideline
Run software
Note
Input 1~4 corresponding EFFECTS
I:single image,II: dual-image,III: three image,
IV: four image,Deal with only 1 layer to show
Layer
Layer input can set as other layer input to come true Matrix.
Note
The set is the same as Matrix.
Layer Scale can set the size and position of image.
Note
The set is the same as Scale.
Layer Tailor can tailor input image
Note
The set is the same as Crop.
Screen Param
User can set screen size as need toed,then click Set,can switching with
FS to realize full screen and scale
VSP 729
User Manual
66
5.Communication Software Guideline
Run software
Set
click 【set】button each time to confirm the setting.
Save
Click 【SAVE 】 to save all the revised parameters.The scrolling list
indicated the location to be saved to. If successfully, user can call it
anytime in the future
;
Update reset
Click this button to recall the factory setting.
Mode control
Interface as following:
VSP 729
User Manual
67
5.Communication Software Guideline
Run software
Preview
Left part is preview window, Input signal information will be shown on the
,such as signal types and its
top left corner
resolution,the
bottom
part‘s
button
1,2,3,4,5
corresponds with preview channel, color green tells button is selected.
Preview image can be switched by buttons 1,2,3,4, 5in order to preview
the four channels.
The set is the same as Preview.
Program
Right part is programme window, Input signal information will be shown on
the top left corner
such as signal types and
its resolution, the
bottom part‘s button 1,2,3,4,5
corresponds with programme channel, Programme output image can be
VSP 729
User Manual
68
5.Communication Software Guideline
Run software
switched by buttons 1,2,3,4, also can drag and drop the image to adjust
the size and position of the programme output Signal.
Note
The set is the same as Program.
Output resolution toolbar
User can choose three output resolutions by selecting from scrolling down
list.
Note
the same as
Advance
Others
Output Format or OUT.
Current config mode
mode:Mode1 refers to single picture,Mode 2 refers to h dual
pictures , mode 3 refers to three pictures. , mode 4 refers to four
pictures.Picture mode only works for Program output, while preview
output always
keeps as single output
Note
The same witch EFFECTS .
Switch mode
CUT:will switch preview image to program output
VSP 729
User Manual
69
5.Communication Software Guideline
Run software
Take:will switch preview image to program output with special effects.
Note
the same as
Advance
Preview Switch
Others
Swap/Stay.
Call saving modes
Click the buttons as followings to apply.
Note
the same as SAVE CONFIG,support six save
mode,VSP729 support ten save modes.
Switch output mode
Cut:will switch preview image to program
output;
Normal:will stay preview image to program output;
Note
the same as
Advance
Swap PROG PRE
VSP 729
User Manual
Others
Swap/Normal.
70
5.Communication Software Guideline
Run software
CUT
seamless cut button,will switch preview image to program
output;
Note
the same as CUT.
Take
seamless transition effects button, will switch preview image to
program output with special effects;
Note
the same as Take.
Effects Toolbar
The device not only provides the most common fade effects(in default),but
also other fourteen seamless transition effects: wipe right ,wipe left ,wipe
up,wipe down, wipe center out, wipe curtain out ,wipe square out etc.
Note
the same as WIPE.
VSP 729
User Manual
71
5.Communication Software Guideline
Run software
Fade duration
set the value for duration(1-30s)from progress toolbar
Note
the same as FADE.
Switch effect speed
set the grades(1-16 grades)for switch speed
Width of transparent toolbar
set the pixels(0-255 pixels) for transparent;
Control
Upgrade
This video processor provide equipment upgrade function.If user have
new MCU need to to renew,can click Upgrade,then will show as
following,select
to enter the path of storage for the MCU.and click to
upgrade.
VSP 729
User Manual
72
5.Communication Software Guideline
Run software
DVI DE Delay
Note
the same as OUT
Setup
Program/Preview
De
HDMI/DVI
VGA Input Adjust
When VGA input signal can't identify or after the bias image recognition.To
realize the VGA input signal simple calibration.So that equipment can
identify VGA signal.
Note
Suggest using automatic adjustment ,If cannot
correction input.Please contact with our
technical engineers.
VSP 729
User Manual
73
5.Communication Software Guideline
Run software
IP setting
With this feature, the user himself can set the device‗s IP. The
function is generally used when the user wants to use the same computer
to do simultaneous manipulation or remote control ,if IP is changed
through serial port, IP changes would take effect immediately ,if IP is
changed through Ethernet port ,user should close the control software
and reopen it use the new IP to do the communication
Factory reset
Click ―factory setup‖, previously saved user-mode will be
cleared.
Note
the same as Reset.
Option
Language
The software support Chinese and English
VSP 729
User Manual
74
5.Communication Software Guideline
Run software
Note
the same as Language.
Administration
Advance Setting
Note
Advance setting is for engineer specially, please
contact with our customer service engineer to get
the code if it is necessary;
Help
Version notice
Display the software version and what is new
About
display the software version and company information
Information toolbar
the button line of the interface of control software shows the Software
Version, Main Board Version, Firmware Version and SN
VSP 729
User Manual
75
5. Communication Software Guideline
How to control processor through RS232?
How to control processor through RS232?
Firstly,install the control software in your PC;
Take out the RS 232 cable as following(RS-232, with 9-pin on one end,
RJ 11 on the other side.) Connect one side of the RJ11 download line to
the RS232 on the video processor VSP729, and the other side to be
connected to the serial port on the PC.
If there is no any Serial port on your PC, you will need another Serial to
USB adapter. Connect one end of the RJ11 download line to the RS232 on
the video processor. Connect the end of USB-side to the PC, Ensure the
cable connection is good. Turn on the Video Processor VSP 729.
Right click the【My Computer】on the home screen of control PC. Enter
【Attribute】, Find【Hardware】Option,as following.
VSP 729
User Manual
76
5. Communication Software Guideline
How to control processor through RS232?
Click【Device Manager】―+‖ on the left,check the COM number,as
following, COM1 is offered.
Remember the COM you are using and then run the control software, find
【Communication】 option. In default,first time user have to click
button,as following:
VSP 729
User Manual
77
5. Communication Software Guideline
How to control processor through RS232?
Check and Press【Serial】
,Serial Port , for example, is COM6 which is
checked from device manager. Set VSP 729 Boud Rate to be :115200,
Click【Confirm】after setting.
Click
【 open serial】
,check if【COM】icon on the bottom right corner,
when there is the prompt green
showing on the
software, it means the communication is ok , and you can use the software
to control the device now.
Note
If power off during communication, should close
the port
, by first, and plug in out of the USB
and do communication.
VSP 729
User Manual
78
5. Communication Software Control Guide
How to control processor with console software by USB?
How to control processor with console
software by USB?
Install the driver
Connect the USB cable to the PC and the video processor .turn on the VSP
729, for the first time to use USB, the PC will remind finding the new
hardware and ask to install the driver for this new driver:
Install from the list or specified location, press ―NEXT‖:
Press ―browser‖ to find the driver, and press ―NEXT‖:
VSP 729
User Manual
79
5. Communication Software Control Guide
How to control processor with console software by USB?
When the installation finish, can go to check the installed COM port inside
the device management, as following picture shows:
VSP 729
User Manual
80
5. Communication Software Control Guide
How to control processor with console software by USB?
Install the console software, and run after install, shows the interface of the
console as following:
Select the COM as installed just now, and set the VSP 729 Boud Rate to
be: 115200.
VSP 729
User Manual
81
5. Communication Software Control Guide
How to control processor with console software by USB?
Press
to start communication,when there is green point in the right
down corner showing on the software, it means the communicationis ok,
and you can use the software to control the device now;the software
operation is the same as VSP 729.
VSP 729
User Manual
82
6. System Setup and Operations
In This Chapter
This chapter provides comprehensive instructions for system setup and
operations. The following topics are discussed:

Interface and input signal choice

Single image switching

Background choice

Multiview image setting

Multiview image switching

Multiview matrix function
VSP 729
User Manual
83
6. System Setup and Operations
Interface and Input Signal Option
Interface and Input Signal Option
NO
INTERFACE
NO
INTERFACE
1~4.9~12
CVBS Input
14.16.23.25
VGA Input
5
Dial switch
17.21
USB Input
6
10/100M Interface
18
Preview Input
7
USB Interface
19
Background Input
8
RS232 Interface
20
Program Output
13.15.22.24
HDMI Input
26.27
Power and Switch
18. Is Preview output interface,preview signal that will be sended through
display.Output signal:DVI video signal and VGA video signal,can switch on
display with DVI or VGA interface to surpervise signal picture.Output signal
through DVI-I( Preview use standard DVI-I interface,Compatible with VGA
output.Contact VGA output through terminal.)
;Support output
resolution:VESA:1024×768×60Hz;
20. Program is main image output,contact sending card,Support VESA:
800×600×60Hz,1024×768×60Hz,1280×768×60Hz,1600×1200×60Hz,
1920×1080×60Hz;
Please click OUT to enter and select corresponding output through knob
switch.And click NEXT to enter.
VSP 729
User Manual
84
6. System Setup and Operations
Interface and Input Signal Option
In addition to CONT and the power interface,Other interface is video signal
input interface.The interface including:HDMI、VGA、YPbPr、YCbCr、
CV.Corresponding four signal source :HDMI1、VGA1、CV1、CV2i is
channel 1;HDMI2、VGA2、CV3、CV4 is channel 2;DMI3、VGA3、CV5、
CV6 is channel 3;DMI4、VGA4、CV7、CV8 is channel4;
The selection of signal format
I f channel 2 need to select VGA input signal,select Preview【2】
,and click
【PROG】to enter signal format,Running the knob switch to select
corresponding input format,select VGA, then click NEXT.
VSP 729
User Manual
85
6. System Setup and Operations
Single Image Switching
Single Image Switching
If it is just simple seamless effects switch between stage pictures, the
settings above are basic completed, just save the existing information and
master switch skills in practice, as follows:
Button Save User Mode Operations
Press CUSTOM and【SAVE】,Six light below SAVE CONFIG lights on is
SAVE1~6,Press 【1】,it means the current parameters is saved to
mode1.When restart the mode1 is defaulted.
Single Image Switch
VSP729 can arbitrary seamless effect switch between 4 channel,Just
choose the channel need to switch to screen firstly.If the light 3 below
Program lights on.It means the screen output the channel3 signal. If need
to switch channel2 signal to the screen,Press 【2】 below Preview,And
seamless effect switch or Press 【TAKE】
【TAKE】default for 3 seconds fade-in fade-out,If need to switch the time
of fade-in fade-out,please Press【FADE】to change the time through the
knob switch,and Press NEXT to affirm.Press TAKE again to recover.If need
to switch other channel signal please Press the corresponding reface 【1】、
【2】、【3】、【4】 below Preview and Press【CUT】or【TAKE】to out.
Size and Position setting
For different channels the size and position is different,VSP729 can realize
the different channel image size and position alone to adjust
arbitrarily .Press the corresponding signal below Preview such as select
VSP 729
User Manual
86
6. System Setup and Operations
Single Image Switching
【2】 ,then Press【SCALE】to enter Scaler,There are four
parameter:Width,Height,Pos X,Pos Y,Please according to the pictures
showed demand to select corresponding parameter and amend
parameter.Then Press 【NEXT】to affirm.It can realize set different picture
size and position at easy through this operation.
VSP 729
User Manual
87
6. System Setup and Operations
Background choice
Background choice
Press 【5】 below Program(or Preview),Knob the switch to enter blank
or vino.User can choose according to demand.
VSP 729
User Manual
88
6. System Setup and Operations
Multiview image setting
Multiview image setting
VSP729 at up to four channel will signal any position and any size output to
the screen,And through the matrix function to set some of the channel
signal set to the same source.So the screen can show the four exactly
same picture .
Size and position setting
The【I】 below EFFECTS is full screen single picture;【II】 is half and half
PBP.【III】is three thirds picture;【IV】is 2*2 four picture.According to the
demand to choose the corresponding number picture.The default setting is
generally can't meet the actual project shows demand.Such as three
picture,general on both sides of the picture is small than the middle's.So
need to set the each picture size and position.
Select corresponding signal through corresponding reface below
Preview.Such as 2,then Press SCALE to enter SCALE.There are four
parameters:Width,Height,Pos X,Pos Y,Please according to the pictures
showed demand .Running the knob switch to choose corresponding and
amend parameters,then Press NEXT to affirm.
VSP 729
User Manual
89
6. System Setup and Operations
Multiview image switching
Multiview image switching
VSP729 can realize seamless switching between multiview and single
picture.Such as set multiview is double picture.it means use channel 1 and
channel 2.Now just can seamless switching with channel and channel.If
switching to channel is invalid.
Similarly,three picture just seamless switching with channel 4.That is the
default output in three pictures,Press 4 below Preview,to realize switching
through CUT or TAKE.
VSP729 by calling the different user mode to realize multiview and single
picture switching:Save the setted corresponding user mode through
SAVE .theVSP729 calls the different user mode to realize multiview and
single picture switching:Save the corresponding set scene through SAVE1
or SAVE 2-SAVE 6,Press SAVE 1 or SAVE 2-SAVE 6 directly to realize
switching.
Four picture used all the layer,so can't switch with single picture or
multiview.Use the call user mode when need to switch.
VSP 729
User Manual
90
6. System Setup and Operations
Multiview Matrix Function
Multiview Matrix Function
If the above operation can't meet the user's pictures showed demand.Such
as want the both side picture of screen be the same size when use three
picture.Or want seamless switch between three picture and the main
picture of three picture.Now need to use VSP729 Matrix.
VSP729 set up a matrix function,It means any input channel can give to
any layer.So can be showed four same signal source on the screen
through the function.
If need to the both side picture of three picture show the channel 1
signal,and realize seamless switch between three picture and the main
picture of three picture.Press MENU firstly,and running the knob switch to
select Matrix,then Press NEXT to enter ,and running the knob to select the
corresponding layer.Such as lay 3.Press NEXT to enter ,running the knob
to select the corresponding input channel ,Such as when need to show
channel 1 signal,please select channel 1,Press NEXT to affirm.In the same
way layer 4 select channel 2.In the same way,layer 4 select input channel
2,after setting Press CUT or TAKE to switch.If still need to use the setting
the next time,just need to SAVE 1 to save the above setting.So the setting
can be used again the next time.
VSP 729
User Manual
91
7. Common Questions and Solution
In This Chapter
This chapter provides the common questions and solution for the video
processor. The following topics are provided:

No Output in Large Screen

Large Screen Output Flash Point

Large Screen only Display Part of the Image

No Display in the Second Half Part of Large Screen

Large Screen Shaking

Left of the Screen Appears Two Black Sides

All Key Lights Light Simultaneously
VSP 729
User Manual
92
7. Common Questions and Solution
No Output in Large Screen
Confirm if there are any input singles
Press【MENU】Button to find "INPUT" and knob into the "INPUT RES INFO"
to see whether the input signal is normal, suggested the "NO INPUT" signal
does not come in, check the front-end signal lines, and please note to do
dual display or extended in computer ; you can enter other format signals to
view in the same operating.
Confirm if single output
Find a belt VGA input (best for DVI) display, connect to the corresponding
outpur port of processor, check whether the signal is correct on the monitor.
If not display properly, please check whether there is input signal, or if input
wire interface is taken tight, output wire interface is picked up tightly. If
display normally, check if sending card is normally working or need to
replace sending card test.
Large Screen Output Flash Point
Confirm if monitor output is normal
Find a belt VGA input (best for DVI) display, connect to the corresponding
outpur port of processor, check whether the signal is correct on the monitor.
If display normally shows and no flash point, please check whether DVI
outlets put tight or replace to DVI line of sending card. If display flash point,
please judge if input signal, wire, and interface is normal.
VSP 729
User Manual
93
7. Common Questions and Solution
Large Screen only Display Part of the
Image
Signal need to scale
Press 【SCALE】button in the processor and knob to adjust the actual
screen size of the screen, combined with button【POSITION】, including the
"width", "height" and "starting position", remember to touch the knob to
confirm.
No Display in the Second Half Part of
Large Screen
Resolution is inadequate
Please make sure the points of the screen width and heigh, choose the
resolution to be bigger than screen width by button【MENU】 under
OUTPUT RES, and touch knob to confirm.
Sending card can't take lower part
TS 802 can control the max horizontal resolution 2048, and vertical
resolution 640. Each CAT5 output is 320 pixels.
Large Screen Shaking
Sending card input recognition is not correct
It usually occurs in DBStar sendig card. Use it‘s normal before, but screen
VSP 729
User Manual
94
7. Common Questions and Solution
sway after change output resolution. It will be normal if re-open the sending
card.
Left of the Screen Appears Two Black
Sides
Adjust DE dethroughtion
This phenomenon needs to adjust the DVI output and DE migration of the
processor, through the 【MENU】 to find "OUTPUT" and find the
corresponding output name, such as "DVI1 OUT ADJUST", and find "DVI1
DE" again, make an adjustment for corresponding horizontal and vertical
DE, please remember to save to the corresponding channel after setting up,
save to SAVE1 by default.
All Key Lights Light Simultaneously
Check if dial switches are normal
Shut the power, check if two red dial switches near CV are upward. Reboot
if they face down, and reboot. The function of the red dial switched is
mainly upgrade.
VSP 729
User Manual
95
A.Specification
CVBS Input
Number of Inputs
8
Connector
Standard BNC Socket
Supported Standards
PAL/NTSC
Signal Level
1Vpp±3db
Multiplex
480i,576i
YPbPr
(0.7V Video+0.3v Sync ) 75 ohm
input
Number of Inputs
4
Connector
Standard DB15 Socket
Supported Standard
Analog HD input
Signal Level
Y:1Vpp±3dB
(0.7V Video+0.3v Sync ) 75 ohm Pb/Pr:0.7Vpp±3dB
75 ohm
Multiplex
480i,576i,480p,576p,720p50,720p60,1080i50,1080p50
1080i60,1080p60
VGA Input
Number of Inputs
4
Connector
Standard DB15 Socket
Supported Standard
VGA-UXGA
Signal Level
R、G、B、Hsync、Vsync:0 to1Vpp±3dB
(0.7V Video+0.3v Sync ) 75
ohm
black level:300mV Sync-tip:0V
Supported Resolution
VGA-UXGA (800*[email protected], 1024*[email protected], 1280*[email protected],
1440*[email protected],1600*[email protected])
DVI Input
Number of Inputs
4
Connector
Standard DVI-I socket
Supported Resolution
SMPTE:625/25/50 PAL, 525/29.97/59.94 NTSC,
1080P50,1080P59.94/60,1080i50,1080i59.94/60,
720p50,720p59.94/60
VESA:800×600×60Hz,1024×768×60Hz,1280×768×60Hz,
1280×1024×60Hz,1600×1200×60Hz,1920×1080×60Hz
Signal Level
TMDS pwl,single pixel input,165MHz bandwidth
Format Standard
HDMI 1.3
Background
Number of Inputs
1
Connector
Standard DVI-I socket
Supported Resolution
VESA:1024×768×60Hz,1280×768×60Hz,
1600×1200×60Hz,1920×1080×60Hz
VSP 729
User Manual
96
Signal Level
TMDS pwl,single pixel input,165MHz bandwidth
Format Standard
HDMI 1.0
Preview DVI output
Number of Outputs
1
Standard
Standard DVI-I socket
Signal Level
TMDS pwl,165MHz bandwidth
Preview VGA Output
Number of Outputs
1
Connector
Standard DB15 Socket
Supported Resolution
VESA: 1024×768×60Hz
Signal Level
R、G、B、Hsync、Vsync:0 to1Vpp±3dB (0.7V Video+0.3v Sync )
75 ohm
black level:300mV Sync-tip:0V
Program DVI Output
Number of Outputs
1
Connector
Standard DVI-I Socket
Supported Resolution
VESA:1024×768×60Hz,1280×768×60Hz,
1600×1200×60Hz,1920×1080×60Hz
Signal Level
TMDS pwl,165MHz bandwidth
Function
Input
channel
configuration
PIP
Support each input channel signal programming configuration
Support PIP、PBP for any two inputs
Transition effects
Fade in and fade out switching between any two inputs
Extras
Communication
RS232
Power Supply
85-264V 2.1A IEC-3
Working Environment
0°C~45°C
Stored Environment
10% to 90%
Product Warranty
1year
VSP 729
USB
TCP/IP
User Manual
97
B. Contact Information
Warranty:
All video products are designed and tested to the highest quality standard
and backed by a full 3-year parts and labor warranty. Warranties are
effective upon delivery date to customer and are non-transferable. RGBlink
warranties are only valid to the original purchase/owner. Warranty related
repairs include parts and labor, but do not include faults resulting from user
negligence, special modification, lighting strikes, abuse(drop/crush), and/or
other unusual damages.
The customer shall pay shipping charges when unit is returned for repair.
Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial
Development Zone Xiamen, Fujian Province, P.R.
VSP 729
User Manual
98
C. Upgrading Software
VSP 729 upgrade firmware
1. Firstly,install the control software in your PC;
2. Input VSP 729 network address in address toolbar: 192.168.0.100,
enter the user name admin and password rgblink123 in the dialog box.
3.Click FPGA Upgrade to enter the upgrade page;
VSP 729
User Manual
99
4. Click browse to select document,the name of document must be
Preamp_FPGA.bin or Bakamp_FPGA.bin;
5. Click【Send】to send,wait for upgade;
6. Upgrade Bakamp FPGA Success.
VSP 729
User Manual
100
Download the IP software
Turn off the power, take the two coding switch to ―ON‖ state as below:
Connect one side of the RJ11 download line to the RS232 on the video
processor, and the other side being connected to the serial port on the PC.
Double click
to run flash magic, setting as below:
Firstly, users can choose the right serial port, set the Boud rate to 9600,
choose LPC2368, and to load the aim document (hex file) for IP board
upgrading; Secondly, confirm the two option box by check.
Finally, click the ―start‖ button.
VSP 729
User Manual
101
After download, exit the program, turn off the power, tack the two coding
switch back, as below restart the equipment power, check if the equipment
work normally.
Note
Flash Magic download website:
http://www.flashmagictool.com/download.html&d
=FlashMagic.exe
VSP 729
User Manual
102
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement