ML610Q174 Reference Board User`s Manual

ML610Q174 Reference Board User`s Manual
FEBL610Q174-01
ML610Q174 Reference Board
User’s Manual
Issue Date: Dec 5, 2013
ML610Q174 Reference Board User’s Manual
NOTES
No copying or reproduction of this document, in part or in whole, is permitted without the consent of LAPIS Semiconductor Co.,
Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing LAPIS Semiconductor 's products (hereinafter "Products"). If you
wish to use any such Product, please be sure to refer to the specifications, which can be obtained from LAPIS Semiconductor upon
request.
Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and
operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any
damage arising from any inaccuracy or misprint of such information, LAPIS Semiconductor shall bear no responsibility for such
damage.
The technical information specified herein is intended only to show the typical functions of and examples of application circuits for
the Products. LAPIS Semiconductor does not grant you, explicitly or implicitly, any license to use or exercise intellectual property
or other rights held by LAPIS Semiconductor and other parties. LAPIS Semiconductor shall bear no responsibility whatsoever for
any dispute arising from the use of such technical information.
The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio
visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While LAPIS Semiconductor always makes efforts to enhance the quality and reliability of its Products, a Product may fail or
malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical
injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and
fail-safe designs. LAPIS Semiconductor shall bear no responsibility whatsoever for your use of any Product outside of the
prescribed scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high
level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury
(such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other
safety device). LAPIS Semiconductor shall bear no responsibility in any way for use of any of the Products for the above special
purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before
purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign
Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Copyright 2013 LAPIS Semiconductor Co., Ltd.
1
ML610Q102 Reference Board User’s Manual
Preface
This manual describes the operation of the ReferenceBoard of the 8-bit microcontroller
ML610Q174.
The following manuals are also available. Read them as necessary.
„ ML610Q174 User’s Manual
Description on the operation of the hardware of the 8-bit microcontroller
ML610Q174.
„ ML610Q172 / ML610Q173 User’s Manual
Description on the operation of the hardware of the 8-bit microcontroller
ML610Q172/ML610Q173.
„ uEASE User’s Manual
Description on the on-chip debug tool uEASE.
2
ML610Q174 Reference Board User’s Manual
1.
Overview
1.1 Features
ML610Q174 Reference board is prepared by LAPIS SEMICONDUCTOR to have you study the operations of
ML610Q174.
The board is arranged so that necessary components are mounted by you according to your purpose, then only
minimum necessary components are mounted on the board by LAPIS SEMICONDUCTOR for brief use of
ML610Q174.
By using the board with "uEASE on-chip debug emulator" (hereinafter referred to "uEASE") and "free sample U8
Development Tools CD-ROM" which is bundled in the package of uEASE not only Software development/debugging
but also writing Flash ROM in the devices are capable.
This board also works in stand alone mode with external power suppy without uEASE.
ML610Q172 and ML610Q173 exist as 64 pin versions of ML610Q174. Please use this board also for development and
debugging of the software of ML610Q172. Please refer to “ML610Q172/ML610Q173 User’s Manual” for the detail of
ML610Q174 and ML610Q172/ML610Q173.
Before starting works with this board, read below carefully and understand notices.
The hardware specification of this board is shown below.
Embedded
microcontroller
U1/U2(Mounting / IC-Socket): ML610Q174
・ UVDD、VSS: Input power supply pin
・ PWR: Jumper for input power supply switch ( 3pin pin-header and short pin )
・ CNUE: Connector for on-chip debug emulator ( 14pin connector )
・ XT_1/XT_2(Mounting / IC-Socket ): 32.768kHz oscillator
・ OSC_1/OSC_2(Mounting / IC-Socket): 8MHz oscillator
・ P20-P23,P90-P91: Light emitting diodes
Embedded parts
・ C1-C3/C10-C12(Mounting / IC-Socket): Capacitors for LCD external input voltage connection(3 pieces)
・ C4/C13(Mounting / IC-Socket): Capacitors for RESET_N pin.
・ C5/C14(Mounting / IC-Socket): Capacitors for VREF input voltage connection.
・ C6-C7/C15-C16: Capacitors for input voltage ( 2pieces )
・ C8-C9/C17-C18(Mounting / IC-Socket): Capacitors for 32.768kHz oscillator ( 2pieces )
・ R1-R6: Resistance for light emitting diodes (P20-P23,P90-P91)
・ R7-R9/R10-R12(Mounting / IC-Socket): Resistance for LCD external input voltage connection(3 pieces)
・ SP1-SP6: Lands for light emitting diodes.
・ SP9-SP10(Mounting / IC-Socket): Lands for P10, P11 terminal connection
Pads
for mounting
・ SP16/SP19(Mounting / IC-Socket): Pads for bonding of P85/VL2 and LCD external input voltage.
・ SP17/SP20(Mounting / IC-Socket): Pads for bonding of P84/VL1 and LCD external input voltage.
・ AIN0-AIN11: Land for SA-ADC terminal connection
・ CN1-CN4: Pads for peripheral board connectors( 30pin×2、20pin×2、2.54mm pitch)
Other useful pads
・ VDD、VSS、UVDD、VREF、AIN0-AIN11
Operating voltage
・ VDD = +2.2V to +5.5V、VREF = +4.5V to +5.5V
Board size
・ 100.00 x 120.00 mm
This board is made on the assumption that it is used carrying in a user circuit. When used with this board simple
substance, please use on an insulating material. An operation abnormality may be caused when used on a conductive
material.
ML610Q174 of the engineering sample may be carried in this board. Please confirm the final confirmation of an
electrical property etc. on mass production goods and customer's production board. The support about this board is not
accepted. Only in the case of initial failure, exchange responds.
3
ML610Q102 Reference Board User’s Manual
1.2 The external view of a board
The external view of ML610Q174 ReferenceBoard is shown.
CN1
PWR
CNUE
UVDD
VSS
XT_2
XT_1
OSC_2
OSC_1
CN4
VREF
U2
Socket
U1
Mounting
CN2
P90-P91
P20-P23
CN3
Fig.1. ML610Q174 ReferenceBoard External view
1pin
Fig.2. Direction of device set
When a device is set to a reference board, please carry out, where the power is turned off. Moreover, please
set not to mistake the direction of a device.
4
ML610Q174 Reference Board User’s Manual
2. Function
2.1 PWR Jumper
It is a jumper which selects the power source of this board. When supplying voltage from uEASE, set a PWR jumper
to the "uE" side.
The ability to supply power of the uEASE is +3.3v/100mA.
When a power supply is inputted from the external, please input between check pin UVDD-VSS and set a PWR jumper
to the "USR" side.
PWR
uE
CNUE
13pin
ML610Q174
VDD
UVDD
USR
Fig.3. PWR Jumper
Note:
Where the PWR jumper is set to the "USR" side, when uEASE is connected, please turn ON the power supply of a
user application system after connecting uEASE. Moreover, please remove uEASE after turning OFF the power
supply of a user application system.
5
ML610Q102 Reference Board User’s Manual
2.2 The case of using successive approximation ADC
When a conversion target is inputted into AIN0-AIN11, without going via CN1/CN4, Please cut the pattern of
AIN0-AIN11 if needed and input from the hole near a device.
The example of processing is shown below.
Top View
Cut Pattern
Please input directly
from the hole of
the side here
after cutting.
Fig.4. AIN0-AIN15 (SA-ADC)
VREF is connected with VDD by the jumper at the time of shipment. When you input arbitrary voltage, please change
a VREF jumper to the USER side and input VREF voltage from 1_CN6 pin (VREF).
The example of processing is shown below.
Top View
Short
Remove
Fig.5. VREF(SA-ADC)
6
ML610Q174 Reference Board User’s Manual
2.3 The case of using light emitting diodes
P20-P23, P90-P91 can drive direct to light emitting diodes. P20-P23, P90-P91 are wired with light emitting diodes on
this board. Please remove the parts mounted in SP1-SP6.
The example of processing is shown below.
Top View
Remove
Fig.6. SP1-SP5 pads
2.4 The case of driving LCDs
The chip resistor of 2012 sizes can be mounted between VL3 to VDD (SP7/SP11 pad). At the time of shipment, since
VDD and VL3 short-circuit, please mount a chip resistor in SP7/SP11 if needed. Please refer to figure 6.( VL3 )
The example of processing is shown below.
Top View
Fig.7. SP7/SP11 pads
Note:
It is a short condition between VL3 and LCD driving voltage input pin (SP15/SP18). Moreover, it is an open condition
between P85/VL2 and an LCD driving voltage input pin (SP16/SP19 pad) and between P85/VL2 and LCD driving
voltage input pin (SP17/SP20).
As for the method of using VL3, P85/VL2 and P84/VL1 as LCD driving power sources, the following three kinds of
methods exist.
・
The LCD external input voltage on a reference board is used.
・
Voltage is inputted from CN1_24 to 26.
・
Voltage is generated using a built-in LCD resistance.
Please be careful for the LCD external input voltage on a reference board, the voltage inputted from CN1_24~26, and
the voltage generated inside LSI not to short-circuit.
7
ML610Q102 Reference Board User’s Manual
2.5 P10-P11 is used as general purpose input ports
P10-P11 can change and use a 8MHz oscillation terminal and a general input port terminal. When you use it as a
general input port terminal, please remove an 8MHz oscillator and short-circuit SP9/SP10 and SP13/SP14,
respectively. Please refer to figure 7. ( P10,P11 8MHz oscillator )
The example of processing is shown below.
Top View
Remove
Short
Fig.7. SP9/SP10、SP13/SP14 pads
8
ML610Q174 Reference Board User’s Manual
3.
User interface
3.1 The user interface of ML610Q174 Reference Board
The pin assignment of CN1, CN2, CN3 and CN4 of the reference board embedded ML610Q174 in below is shown.
Table 1. ML610Q174 Reference Board CN1 / CN2
CN1
Name
1
2
P44/T0P4CK/AIN4/SIN0
P33/AIN3
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
P32/AIN2
P31/PW6EV1/AIN1
P30/PW45EV1/AIN0
VREF
P50/AIN8/SIN1
P51/AIN9/SCK1
P52/CMP0P/RXD1/SOUT1
P53/CMP1P/TXD1/PWM6/TXD0
P34/AIN11/PWM4
P35/AIN10/PWM5
P36/LSCLK
NC
NC
P10/OSC0
P11/OSC1
VSS
UVDD
NC
NC
NC
NC
VL3
P85/VL2
P84/VL1
P83/COM3
P82/COM2
P81/COM1
P80/COM0
LSI
Pin No.
19
20
21
22
23
24
15
14
13
12
10
11
33
----25
26
27
28
--------34
35
36
37
38
39
40
9
CN2
Name
1
2
SEG0
SEG1
LSI
Pin No.
41
42
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
PC0/SEG8
PC1/SEG9
PC2/SEG10
PC3/SEG11
PC4/SEG12
PC5/SEG13
PC6/SEG14
PC7/SEG15
PD0/SEG16
PD1/SEG17
PD2/SEG18
PD3/SEG19
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
ML610Q102 Reference Board User’s Manual
Table 2. ML610Q174 Reference Board CN3 / CN4
CN3
Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
PD4/SEG20
PD5/SEG21
PD6/SEG22
PD7/SEG23
NC
NC
NC
NC
NC
NC
NC
NC
PF0/SEG32/SIN0
PF1/SEG33/SCK0
PF2/SEG34/RXD0/SOUT0
PF3/SEG35/TXD0/PWM4/TXD1
PF4/SEG36/SIN1/PWM4
PF5/SEG37/SCK1/PWM5
PF6/SEG38/RXD1/SOUT1/PWM6
PF7/SEG39/TXD1/TXD0
RESET_N
P40/SDA/SIN0
P41/SCL/SCK0
P42/RXD0/SOUT0
P43/TXD0/PWM4/TXD1
P00/EXI0/PW45EV0
P01/EXI1/PW6EV0
P02/EXI2/RXD0
P03/EXI3/RXD1
NC
LSI
Pin No.
61
62
63
64
----------------65
66
67
68
69
70
71
72
32
6
7
8
9
75
76
77
78
---
10
CN4
Name
LSI
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
P20/LED0/LSCLK/PWM4
P21/LED1/OUTCLK/PWM5
P22/LED2/TM9OUT
P23/LED3/TMBOUT
VSS
P90/LED4
P91/LCD5
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
P47/T9BCK/AIN7/CMP1M
P46/T8AP6CK/AIN6/CMP0M
P45/T1P5CK/AIN5
79
80
2
3
1
4
5
--------------------16
17
18
ML610Q174 Reference Board User’s Manual
4.
The circuit diagram and substrate dimensional drawing
The circuit diagram and substrate dimensional drawing of this board are shown after a next page.
11
A
B
P20
560
R6
P21
LED
560
R5
P22
LED
560
R4
P23
LED
560
R3
P90
LED
560
R2
P91
LED
1
LED
560
R1
VDD
PIN2
2/1D
PIN3
2/1D
PIN4
2/1D
PIN5
2/1D
PIN6
PIN7
2/2C
2/2C
PIN8
2/2C
PIN9
2/2C
SP6
PIN79
SP5
PIN80
SP4
PIN2
SP3
SP2
PIN3
PIN4
PIN5
SP1
PIN10
PIN11
AIN11
2/1A
PIN13
2/1A
PIN14
AIN9
P23/LED3
I/O
P90/LED4
I/O
P91/LED5
I/O
P40/SDA
I/O
P41/SCL
PIN15
PIN16
P43/TXD0
I/O
P34/AIN11
P35/AIN10
I/O
P53/TXD1
P52/RXD1
I/O
2/1A
I/O
2/1A
AIN3
2/1A
AIN2
PIN21
2/1A
AIN1
PIN22
P51/AIN9
2/2D
AIN4
PIN20
I/O
2/2D
AIN5
PIN18
I/O
2/2D
AIN6
PIN17
P42/RXD0
2/1A
AIN7
PIN19
2/2A
PIN12
P22/LED2
I/O
I/O
2/1A
AIN10
I/O
2/1A
AIN0
PIN23
D
C
AIN8
2/1A
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
P50/AIN8
P47/AIN7
P46/AIN6
P45/AIN5
P44/AIN4
P33/AIN3
P32/AIN2
P31/AIN1
P30/AIN0
PIN32
PIN33
2/2C
2/2A
PIN34
2/2A
PIN35
2/2A
PIN36
PIN37
2/2A
2/2A
PIN38
2/2A
PIN39
2/2A
PIN40
PIN41
2/2A
2/1B
PIN42
2/1B
PIN43
2/1B
PIN44
2/1B
PIN45
2/1B
PIN46
2/1B
PIN47
2/1B
PIN48
2/1B
I/O
RESET_N
I/O
I/O
P36/LSCLK
VL3
I/O
P85/VL2
I/O
P84/VL1
I/O
P83/COM3
I/O
P82/COM2
P81/COM1
I/O
P80/COM0
I/O
SEG0
SEG1
I/O
SEG2
I/O
SEG3
I/O
SEG4
SEG5
I/O
I/O
SEG6
I/O
SEG7
PIN51
PIN52
I/O
I/O
PIN49
PIN50
2/1B
2/1B
2/1B
2/2B
PIN53
PIN54
2/2B
PIN55
2/2B
PIN56
2/2B
PIN57
PIN58
2/2B
PIN59
2/2B
2/2B
PIN60
2/2B
2/2B
PIN61
PIN62
2/1C
PIN63
2/1C
PIN64
2/1C
2/1C
I/O
PC0/SEG8
I/O
I/O
PC1/SEG9
PC2/SEG10
I/O
PC3/SEG11
I/O
PC4/SEG12
I/O
PC5/SEG13
I/O
PC6/SEG14
I/O
PC7/SEG15
I/O
PD0/SEG16
I/O
PD1/SEG17
PD2/SEG18
I/O
I/O
PD3/SEG19
I/O
PD4/SEG20
I/O
PD5/SEG21
PD6/SEG22
I/O
I/O
PD7/SEG23
PIN65
PIN66
2/2C
2/2C
PIN67
2/2C
PIN68
2/2C
PIN69
PIN70
2/2C
2/2C
PIN71
2/2C
PIN72
2/2C
PIN73
PIN74
2/3A
2/3A
PIN75
2/2C
PIN76
2/2C
PIN77
PIN78
2/2C
2/2C
PIN79
2/1D
PIN80
2/1D
PF0/SEG32
I/O
I/O
PF1/SEG33
PF2/SEG34
I/O
PF3/SEG35
I/O
PF4/SEG36
I/O
PF5/SEG37
I/O
PF6/SEG38
I/O
PF7/SEG39
I/O
TEST0
I/O
I/O
TEST1_N
P00/EXI0
I/O
P01/EXI1
I/O
P02/EXI2
I/O
P03/EXI3
I/O
P20/LED0
I/O
P21/LED1
VDD
SP7
VSS
PIN64
PIN63
PIN62
PIN61
PIN60
PIN59
PIN58
PIN57
PIN56
PIN55
PIN54
PIN53
PIN52
PIN51
PIN50
PIN49
PIN48
PIN47
PIN46
PIN45
PIN44
PIN43
PIN42
PIN41
VSS
IN
200K
R10
0.22UF C12
PIN36
C13
VSS
PIN32
SP20
200K
R12
2.2UF
2
VSS
12PF
1
3
VSS
VSS
OSC_2
1
VSS
SP14
VSS
3
2
SP13
SP9
VDD
SP19
XT_2
2
VDD
USR
3
SP10
PIN24
VREF_IN
0.22UF C11
PIN35
SP22
PIN2
PIN3
PIN4
PIN5
PIN6
PIN7
PIN8
PIN9
PIN10
PIN11
PIN12
PIN13
PIN14
PIN15
PIN16
PIN17
PIN18
PIN19
PIN20
PIN21
PIN22
PIN23
PIN24
OSC_1
1
C
2/1A
PIN40
PIN39
PIN38
PIN37
PIN36
PIN35
PIN34
PIN33
PIN32
1UF C14
PIN2
PIN3
PIN4
PIN5
PIN6
PIN7
PIN8
PIN9
PIN10
PIN11
PIN12
PIN13
PIN14
PIN15
PIN16
PIN17
PIN18
PIN19
PIN20
PIN21
PIN22
PIN23
PIN24
1UF C5
PIN[80:1]
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
200K
R11
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
U2
2
C18
VSS
C9 12PF
C8 12PF
VSS
2
IC_SOCKET
P80/COM0
P81/COM1
P82/COM2
P83/COM3
P84/VL1
P85/VL2
VL3
P36/LSCLK
RESET_N
XT1
XT0
VDDL
VDD
VSS_27
P11/OSC1
P10/OSC0
C17 12PF
XT_1
1
PF0/SEG32
PF1/SEG33
PF2/SEG34
PF3/SEG35
PF4/SEG36
PF5/SEG37
PF6/SEG38
PF7/SEG39
TEST0
TEST1_N
P00/EXI0
P01/EXI1
P02/EXI2
P03/EXI3
P20/LED0
P21/LED1
C16 10UF SP12
PIN32
SP17
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
C15 10UF
C4
200K
R9
2.2UF
C3
PIN65
PIN66
PIN67
PIN68
PIN69
PIN70
PIN71
PIN72
PIN73
PIN74
PIN75
PIN76
PIN77
PIN78
PIN79
PIN80
PD7/SEG23
PD6/SEG22
PD5/SEG21
PD4/SEG20
PD3/SEG19
PD2/SEG18
PD1/SEG17
PD0/SEG16
PC7/SEG15
PC6/SEG14
PC5/SEG13
PC4/SEG12
PC3/SEG11
PC2/SEG10
PC1/SEG9
PC0/SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0
C2
VSS_1
P22/LED2
P23/LED3
P90/LED4
P91/LED5
P40/SDA
P41/SCL
P42/RXD0
P43/TXD0
P34/AIN11
P35/AIN10
P53/TXD1
P52/RXD1
P51/AIN9
P50/AIN8
P47/AIN7
P46/AIN6
P45/AIN5
P44/AIN4
P33/AIN3
P32/AIN2
P31/AIN1
P30/AIN0
VREF
PIN36
0.22UF
SP18
VSS
VSS
200K
R8
SP16
SP21
VSS
3
0.22UF
PIN35
VSS
PIN40
PIN39
PIN38
PIN37
PIN36
PIN35
PIN34
PIN33
PIN32
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VSS_1
P22/LED2
P23/LED3
P90/LED4
P91/LED5
P40/SDA
P41/SCL
P42/RXD0
P43/TXD0
P34/AIN11
P35/AIN10
P53/TXD1
P52/RXD1
P51/AIN9
P50/AIN8
P47/AIN7
P46/AIN6
P45/AIN5
P44/AIN4
P33/AIN3
P32/AIN2
P31/AIN1
P30/AIN0
VREF
U1
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
C7 10UF SP8
ML610Q174
P80/COM0
P81/COM1
P82/COM2
P83/COM3
P84/VL1
P85/VL2
VL3
P36/LSCLK
RESET_N
XT1
XT0
VDDL
VDD
VSS_27
P11/OSC1
P10/OSC0
C6 10UF
PF0/SEG32
PF1/SEG33
PF2/SEG34
PF3/SEG35
PF4/SEG36
PF5/SEG37
PF6/SEG38
PF7/SEG39
TEST0
TEST1_N
P00/EXI0
P01/EXI1
P02/EXI2
P03/EXI3
P20/LED0
P21/LED1
0.22UF C10
PIN34
VDD
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
PD7/SEG23
PD6/SEG22
PD5/SEG21
PD4/SEG20
PD3/SEG19
PD2/SEG18
PD1/SEG17
PD0/SEG16
PC7/SEG15
PC6/SEG14
PC5/SEG13
PC4/SEG12
PC3/SEG11
PC2/SEG10
PC1/SEG9
PC0/SEG8
SEG7
SEG6
SEG5
SEG4
SEG3
SEG2
SEG1
SEG0
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
200K
R7
SP15
VDD
PIN65
PIN66
PIN67
PIN68
PIN69
PIN70
PIN71
PIN72
PIN73
PIN74
PIN75
PIN76
PIN77
PIN78
PIN79
PIN80
C1
PIN34
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
0.22UF
PIN64
PIN63
PIN62
PIN61
PIN60
PIN59
PIN58
PIN57
PIN56
PIN55
PIN54
PIN53
PIN52
PIN51
PIN50
PIN49
PIN48
PIN47
PIN46
PIN45
PIN44
PIN43
PIN42
PIN41
2
1
SP11
VDD
I/O
VREF
P10
IN
P11
IN
2/2A
2/2A
LAPIS Semiconductor Co., Ltd.
TITLE
4
ML610Q174 Reference Board
APPLICATION
ML610Q174
DWG NO
DRAWN By
A
B
C
QTS-11583
SHEET
1 of 2
D
REV
1.00
4
A
B
CN1
CN30P
1
P44/AIN4
P33/AIN3
P32/AIN2
P31/AIN1
P30/AIN0
VREF_IN
P50/AIN8
P51/AIN9
P52/RXD1
P53/TXD1
P34/AIN11
P35/AIN10
P36/LSCLK
P10
P11
2
VL3
P85/VL2
P84/VL1
P83/COM3
P82/COM2
P81/COM1
P80/COM0
I/O
I/O
I/O
I/O
I/O
OUT
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
1/2A
1/2A
1/2A
1/2A
1/2A
1/4A
1/2A
1/1A
1/1A
1/1A
1/2A
1/2A
1/2A
PIN15
PIN14
PIN13
PIN12
PIN10
PIN11
PIN33
1/4B
1/4B
1/2A
1/2A
1/1C
1/2A
1/2A
1/2A
1/2A
PIN34
PIN35
PIN36
PIN37
PIN38
PIN39
PIN40
CN3
CN30P
CN2
CN20P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
PIN19
PIN20
PIN21
PIN22
PIN23
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
PC0/SEG8
PC1/SEG9
PC2/SEG10
PC3/SEG11
PC4/SEG12
PC5/SEG13
PC6/SEG14
PC7/SEG15
PD0/SEG16
PD1/SEG17
PD2/SEG18
PD3/SEG19
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
1/2A
D
C
PIN41
PIN42
PIN43
PIN44
PIN45
PIN46
PIN47
PIN48
PIN49
PIN50
PIN51
PIN52
PIN53
PIN54
PIN55
PIN56
PIN57
PIN58
PIN59
PIN60
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PD4/SEG20
PD5/SEG21
PD6/SEG22
PD7/SEG23
PF0/SEG32
PF1/SEG33
PF2/SEG34
PF3/SEG35
PF4/SEG36
PF5/SEG37
PF6/SEG38
PF7/SEG39
RESET_N
P40/SDA
P41/SCL
P42/RXD0
P43/TXD0
P00/EXI0
P01/EXI1
P02/EXI2
P03/EXI3
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
1/2A
1/2A
1/2A
1/2C
1/2A
1/1D
1/1D
1/1D
1/1D
1/1D
1/2A
1/1D
1/2A
1/1A
1/1A
1/1A
1/1A
1/1D
1/1D
1/1D
1/1D
PIN61
PIN62
PIN63
PIN64
PIN65
PIN66
PIN67
PIN68
PIN69
PIN70
PIN71
PIN72
PIN32
PIN6
PIN7
PIN8
PIN9
PIN75
PIN76
PIN77
PIN78
CN4
CN20P
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
P20/LED0
P21/LED1
P22/LED2
P23/LED3
OUT
OUT
OUT
OUT
P90/LED4
P91/LED5
OUT
OUT
P47/AIN7
P46/AIN6
P45/AIN5
I/O
I/O
I/O
1/1D
1/2A
1/2A
1/2A
PIN79
PIN80
PIN2
PIN3
1/1A
1/1A
PIN4
PIN5
1/2A
1/2A
1/2A
PIN16
PIN17
PIN18
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
VSS
2
VSS
VDD
UE
C
PWR
USR
UVDD
VDD
CNUE
CN14P
3
3
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PIN74
1/1D
PIN73
1/1D
IN
I/O
TEST1_N
TEST0
VSS
VSS
LAPIS Semiconductor Co., Ltd.
TITLE
4
ML610Q174 Reference Board
APPLICATION
ML610Q174
DWG NO
DRAWN By
A
B
C
QTS-11583
SHEET
2 of 2
D
REV
1.00
4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement