User Manual

Part Number:

Important: Read all instructions prior to installation.

RGB LED Controller with Wireless RF Remote

9

Parts Included

Model

Dynamic Mode

Static Color

PWM Grade

RGB10

43 Modes

30 Colors

256 Levels

1 3

1 - LED Controller

1 - Wireless Remote

Brightness Grade

Speed Grade

Overload Protection

Overheat Protection

5 Levels

10 Levels

Yes

Yes

DC 5-24V

433.92MHz

Up to15 Meters (Open Area)

-30° to 80°

3 x 3.5A

2 4

5

Wireless Remote

1. Turn On(|) / Standby(O)

Turns on controller or enters standby mode.

Working Voltage

Remote Frequency

Remote Distance

Working Temperature

Rated Output Current

PWM Frequency 1 KHz

6 7

8

2. Ascend(+)/Descend(-) Dynamic Modes

Dynamic modes feature a variety of static color transitions and patterns, with 43 distinct modes.

IP Grade

These buttons initiate Dynamic Mode and cycle through the modes in ascending(+) or descending(-) order.

3. Play (u = ) / Pause

Toggles between run/pause when in Dynamic Mode or Demo Mode. Initiates Dynamic Mode if

Static Color Mode is currently active.

4. Increase(+)/Decrease(-) Tempo Speed Level

Increases(+) or decreases(-) the tempo of the currently active dynamic mode. Initiates Dynamic

Mode if Static Color Mode is currently active.

IP-68 (Waterproof) 12

10 13

Remote Pairing Options

11

To

Power

Pairing A New Remote: Up to 3 wireless remotes can be assigned to operate the LED controller. Additionally, each individual wireless remote can be assigned to an unlimited number of controllers. The following steps show how to assign a new remote to the LED Controller:

5. Demo Mode

Initiates Demo Mode. Demo Mode cycles through 27 individual modes, repeating each 3 times.

6. Ascend(+)/Descend(-) Static Colors

These buttons initiate Static Color Mode and cycle through the colors in ascending(+) or descending(-) order.

1. Disconnect the power to the LED controller, wait 5 seconds, and reconnect.

2. Within 5 seconds of reconnecting the LED Controller, press the “Mode(-)” and “Speed(-)” buttons simultaneously.

3. The LED indicator on the LED controller will flash white 3 times indicating the new wireless remote has been successfully assigned. This may be done for a total of 3 wireless remotes.

9

7. Increase(+)/Decrease(-) Static Color Brightness Level

Increases(+) or decreases(-) the brightness of the currently active static color. Initiates Static

Color Mode if Dynamic Mode is currently active.

8. Direct Color Select

Activates the static color indicated by the button color. These individual colors are also accessible through the Ascend(+)/Descend(-) Static Colors buttons.

9. Wireless Remote LED Indicator

Flashes blue when remote is operated to indicate that remote is functioning properly.

RGB LED Controller

Pairing Any Remote: Up to 3 wireless remotes can be assigned to operate the

LED controller. The following steps show how to assign a new remote to the

LED Controller:

1 3

2

4. Disconnect the power to the LED controller, wait 5 seconds, and reconnect.

5. Within 5 seconds of reconnecting the LED Controller, press the “On(|)” and

6. The LED indicator on the LED controller will flash yellow 3 times indicating the LED controller will recognize any remote.

4

“Play/Pause (u = 6

5

7

8

12

10. Power Supply Wiring

The controller/power supply operates on 5-24VDC. The red wire is positive(+) and the black wire is negative(-) as indicated on the controller housing.

11. LED Output Wiring

The controller supports common anode-type LED products. Output wires are indicated as follows:

Black(V+): Common node which connects as the positive (line) connection inside the controller.

Red(R): Wire connection for red LED color signals.

Green(G): Wire connection for green LED color signals.

Blue(B): Wire connection for blue LED color signals.

Light Signal

12. Wiring Connectors

Use wiring connectors to make connections between wiring. Be sure to maintain polarity and wiring color when connecting wiring. Dolphin connectors are shown here.

Indicates

13. LED Controller Status Indicator

A multi-color emitting LED located on the remote controller indicates current operating status or operating status changes as follows:

Blue normal functioning mode

To

Power

Supply

Short single white flash

RGB LED Controller Status Indicator lighting change

Long single white flash

Range limit has been reached when cycling through Dynamic or Static color modes

Long single yellow flash

Range limit has been reached when cycling through Tempo

Speed Level or Static color

Brightness Level

Blue flash Red flash

Dynamic mode is paused

Overload/short circuit has been detected, activating protection mode

Using the Wireless Remote

Prepare the wireless remote for use by removing the battery insulating tape. The remote uses a 3V CR2025 battery.

Note: The wireless remote operates using radio frequency.

The remote controller’s use is not restricted by normal obstructions such as walls, doors, etc.

10 13

Additional Features

11

To

Device

Yellow flash

Overheating has been detected, activating protection mode

Waterproof LED Controller - The MCBRF-RGB10 LED controller is fully waterproof according to the IP68 standard and can be installed and operated underwater up to a depth of

30 meters. Note: LED controller sensitivity to wireless remote signals will decrease when operated in underwater conditions.

Make sure to perform all wiring connections and setup prior to installing LED controller underwater.

4400 Earth City Expy, St. Louis, MO 63045 866-590-3533 superbrightleds.com

To

Device