MultiBio 700 Installation Guide

MultiBio 700 Installation Guide
! Warning: No operating with power on
MultiBio 700 Installation Guide
Version: V1.0
Date: October 2010
3.Lock Connection
(1) Share power with the lock:
+
+12V
In st ru ct io n fo r th e Mo un ti ng P ap er
GND
DC12V
Be fo re t he d ev ic e is f as te ne d, p le as e
st ic k th e pa pe r to t he p la ce w he re y ou
wa nt t o in st al l it , th en m ak e ho le s an d
la y ca bl es a cc or di ng t o th e mo un ti ng
pa pe r.
Wiring Hole
10
NC LOCK
-
12
+
11
FR 107
(2) Remove the screw on the bottom
(3) Take away the back plate.
+
-
of device.
DC12V
NO LOCK
FR 107
+
BELLBELL+
SEN
GND
BUT
NO
COM
NC
AL+
AL-
Device share power with the lock:
A. ULOCK=12V, I-ILOCK>1A…… ①
B. The lock is near to the device.
(2) Does not share power with the lock:
+
+
FR 107
+
-
(5) Fix the device to the back plate.
NC LOCK
BELLBELL+
SEN
GND
BUT
NO
COM
NC
AL+
AL-
+12V
GND
DC12V
-
+
DC power
+
+12V
GND
-
DC12V
(4) Fix the back plate on the wall
according to the mounting paper.
-
+
(1) Post the mounting template on the
wall.Drill the holes according to
the marks on the template (holes
for screw and wiring).
BELLBELL+
SEN
GND
BUT
NO
COM
NC
AL+
AL-
+12V
GND
-
-
MultiBio 700 Mounting Paper
(only for your reference)
+
+
1. Equipment Installation
NO LOCK
FR 107
+
+
DC power
Device does not share power with the lock:
BELLBELL+
SEN
GND
BUT
NO
COM
NC
AL+
AL-
A. ULOCK=12V I-ILOCK≤1A;
B. ULOCK≠12V;
C. The lock is far apart from the device.
(1) The system supports NO LOCK and NC LOCK. For example the NO LOCK (normally open at power on) is connected
with ’NO’ terminal, and the NC LOCK is connected with ‘NC’ terminal.
2. Structure and Function
(2) When the Electrical Lock is connected to the Access Control System, you need to parallel one FR107 diode
Access Control System Function
(1) If a registered user verified, the device will export the signal
to unlock the door.
TCP/IP
RS485
⑦
RS232/RS485 Converter
Exit Button
④
①
⑤
EXIT
BUTTON
⑥
②
(2) Door sensor will detect the on-off state. If the door is un-
(equipped in the package) to prevent the self-inductance EMF affect the system, do not reverse the polarities.
4. Other Parts Connection:
expected opened or improperly closed, the alarm signal
(digital value) will be triggered.
Door Bell
% (4) External card reader is supported.
Door Bell External Reader
③
Alarm
EXIT
BUTTON
Exit Button
Alarm Power
(5) External exit button is supported, it is convenient to open the
door inside.
+
(6) External door bell is supported.
-
(7) Supports RS485, TCP/IP modes to connect with PC. One PC can
manage multiple devices.
Input DC 12V, 500mA (50mA standby)
Positive is connected with ‘+12V’, negative is connected
with ’GND’ (do not reverse the polarities).
%
(3) If only the device being illegally removed, the device will
export alarm signal.
Lock Sensor
BELLBELL+
SEN
GND
BUT
NO
COM
NC
AL+
AL-
5. Power Connection:
Alarm
+
Door Sensor
-
DC12V
Voltage output ≤ DC 12V for Alarm
①:‘I’: device output current, ‘ULOCK’: lock voltage,‘ILOCK’: lock current
+12V
GND
! Warning: No operating with power on
6. Wiegand Output
7. Wiegand Input
The device supports standard Wiegand 26 output,
The device has the function of Wiegand signal input. It supports to
so you can connect it with most of the access control
connect with an independent card reader. They are installed each
devices by now.
side of the door, to control the lock and access together.
485Access Control
12Vout
485+
GND
IWD1
RXD
GND
DATA0
DATA1
IWD0
TXD
RLED
GND
GLED
WD 0
WD 1
BEEP
485+
485-
Please use specified RS485 wire, RS485 active converter and
bus-type wiring.
485+ 485-
Terminals:
+12V
Terminals
GND
GND
(2) RS485 Mode:
DATA1
DATA0
PC Serial Ports
485+
RS485+
485-
RS485-
RS485 Bus
485+
485-
485+
485-
RS485
Converter
RLED
GLED
BEEP
(3) TCP/IP Mode:
(1) Please keep the distance between the device and Access Control or Card Reader less than 90 meters(Please use
Wiegand signal extender in long distance or interference environment).
(2) To keep the stability of Wiegand signal, connect the device and the Access Control or Card Reader in same ‘GND’
in any case.
(A) Crossover cable: The device and PC connected
directly.
(B) Straight cable: The device and PC connected to
LAN/WAN through switch/Lanswitch.
PC
8.Other Functions
Switch
IP Address:192.168.1.100
Subnet Mask:255.255.255.0
(1) Manual Reset:
If the device does not work properly because of misoperation or
other abnormality, you can use ‘Reset’ function to restart it.
Operation: Remove the black rubber cap, then stick the Reset button
hole with a sharp tool (the tip diameter less than 2mm).
Side View
Back View
…
IP Address:192.168.1.124
Subnet Mask:255.255.255.0
(2) Restore Factory Settings:
You can use the tamper switch to restore factory settings, such
as device number, system password, IP address, RS485 address,
etc. More information please refer to the user manual.
Operation: Press the tamper switch three times after the alarm being
triggered 30 seconds but no more than 60 seconds.
10. Cautions:
Reset Button
Tamper Switch
Note: The user data won’t be cleared.
(1)Power cable is connected after all the other wiring. If the device is working abnormally, please shut down the power
first, then make the necessary check . Kindly reminds you that any hot-plugging may damage the device, and
it is not included in the warranty.
(2)We recommend the 3A/12V DC Power supply. Please contact our technical staff for details.
9. Communication
(3)Please read carefully the terminal description and wiring by rule strictly. Any damage caused by improper
operations will be out of the range of our guarantee.
There are three modes that the PC software communicate
and exchange information with the device: RS232, RS485
and TCP/IP, and the last two modes support remote control. Terminals:
(1) RS232
Mode:
(4)Keep the exposed part of wire less than 5mm, to avoid unexpected connection.
Terminals
PC Serial Ports
GND
Pin5-Gnd
RXD
Pin3-Txd
TXD
Pin2-Rxd
(5)Please connect the ‘GND’ before all the other wiring especially under the environment with much electrostatic.
(6)Do not change the cable type because of long distance between the power and the device.
(7) Please use specified RS485 wire, RS485 active converter and bus-type wiring.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement