Amana AMH95 Instruction manual
AMH95
GAS-FIRED WARM AIR FURNACE
INSTALLATION INSTRUCTIONS
Installer: Affix all manuals adjacent to the unit.
(Type FSP CATEGORY IV Direct or Non Direct Vent Air Furnace)
These furnaces comply with requirements
embodied in the American National Standard / National Standard of Canada ANSI
Z21.47·CSA-2.3 Gas Fired Central Furnaces.
®
C
US
RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.
ATTENTION INSTALLING PERSONNEL
As a professional installer you have an obligation to know the product better than the customer. This includes all safety
precautions and related items.
Prior to actual installation, thoroughly familiarize yourself with this Instruction Manual. Pay special attention to all safety
warnings. Often during installation or repair it is possible to place yourself in a position which is more hazardous than
when the unit is in operation.
Remember, it is your responsibility to install the product safely and to know it well enough to be able to instruct a customer
in its safe use.
Safety is a matter of common sense...a matter of thinking before acting. Most dealers have a list of specific good safety
practices...follow them.
The precautions listed in this Installation Manual are intended as supplemental to existing practices. However, if there is
a direct conflict between existing practices and the content of this manual, the precautions listed here take precedence.
*NOTE: Please contact your distributor or our
website for the applicable product data book
referred to in this manual.
is a trademark of Maytag Corporation and is used under
license to Goodman Company, L.P. All rights reserved.
®
www.amana-hac.com
IO-297
© 2006 Goodman Company, L.P.
6/06
Table of Contents
I. Component Identification ............................................................................................................................................... 5
II. Safety .............................................................................................................................................................................. 6
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS ................................................................................................... 6
III. Product Application ...................................................................................................................................................... 6
IV. Location Requirements & Considerations ................................................................................................................. 7
GENERAL ......................................................................................................................................................... 7
CLEARANCES AND ACCESSIBILITY ........................................................................................................................... 8
FURNACE SUSPENSION ........................................................................................................................................ 8
EXISTING FURNACE REMOVAL .............................................................................................................................. 8
THERMOSTAT LOCATION ....................................................................................................................................... 9
V. Combustion & Ventilation Air Requirements ............................................................................................................... 9
VI. Installation Positions ................................................................................................................................................... 11
VII. Horizontal Applications & Considerations ................................................................................................................ 11
GENERAL ........................................................................................................................................................11
DRAIN TRAP AND LINES .....................................................................................................................................11
LEVELING ........................................................................................................................................................11
ALTERNATE VENT/FLUE AND COMBUSTION AIR CONNECTIONS .....................................................................................11
ALTERNATE ELECTRICAL AND GAS LINE CONNECTIONS ............................................................................................ 12
DRAIN PAN ..................................................................................................................................................... 12
FREEZE PROTECTION ........................................................................................................................................ 12
FURNACE SUSPENSION ...................................................................................................................................... 12
VIII. Propane Gas /High Altitude Installations ............................................................................................................... 12
IX. Vent/Flue Pipe & Combustion Air Pipe ..................................................................................................................... 12
GENERAL ....................................................................................................................................................... 12
DUAL CERTIFICATION: NON-DIRECT/DIRECT VENT ................................................................................................... 13
MATERIALS AND JOINING METHODS ..................................................................................................................... 13
PROPER VENT/FLUE AND COMBUSTION AIR PIPING PRACTICES ................................................................................. 13
TERMINATION LOCATIONS ................................................................................................................................... 13
CANADIAN VENTING REQUIREMENTS ..................................................................................................................... 14
STANDARD FURNACE CONNECTIONS ..................................................................................................................... 14
ALTERNATE FURNACE CONNECTIONS ..................................................................................................................... 14
NON-DIRECT VENT (SINGLE PIPE) PIPING ............................................................................................................ 15
DIRECT VENT (DUAL PIPE) PIPING ...................................................................................................................... 16
VENT/INTAKE TERMINATIONS FOR INSTALLATION OF MULTIPLE DIRECT VENT FURNACES .................................................. 18
CONCENTRIC VENT TERMINATION ......................................................................................................................... 18
X. Condensate Drain Lines & Drain Trap ........................................................................................................................ 18
GENERAL ....................................................................................................................................................... 18
UPRIGHT INSTALLATIONS ..................................................................................................................................... 18
HORIZONTAL INSTALLATIONS ................................................................................................................................ 19
XI. Electrical Connections ................................................................................................................................................ 21
WIRING HARNESS ............................................................................................................................................ 21
115 VOLT LINE CONNECTIONS ............................................................................................................................ 21
24 VOLT THERMOSTAT WIRING ............................................................................................................................ 22
115 VOLT LINE CONNECTION OF ACCESSORIES (ELECTRONIC AIR CLEANER) .............................................................. 22
24 VOLT HUMIDIFIER ........................................................................................................................................ 22
XII. Gas Supply and Piping .............................................................................................................................................. 22
GENERAL ....................................................................................................................................................... 22
GAS PIPING CONNECTIONS ................................................................................................................................ 23
PROPANE GAS TANKS AND PIPING ...................................................................................................................... 24
XIII. Circulating Air & Filters ............................................................................................................................................ 25
DUCTWORK - AIR FLOW ..................................................................................................................................... 25
BOTTOM RETURN AIR OPERNING [UPFLOW MODELS] ............................................................................................. 26
FILTERS - READ THIS SECTION BEFORE INSTALLING THE RETURN AIR DUCTWORK ....................................................... 26
UPRIGHT INSTALLATIONS ..................................................................................................................................... 26
HORIZONTAL INSTALLATIONS ................................................................................................................................ 26
2
Table of Contents
XIV. Startup Procedure & Adjustment ............................................................................................................................. 27
HEAT ANTICIPATOR SETTING ................................................................................................................................ 27
DRAIN TRAP PRIMING ....................................................................................................................................... 27
FURNACE OPERATION ......................................................................................................................................... 27
GAS SUPPLY PRESSURE MEASUREMENT .............................................................................................................. 27
GAS MANIFOLD PRESSURE MEASUREMENT AND ADJUSTMENT .................................................................................. 28
GAS INPUT RATE MEASUREMENT (NATURAL GAS ONLY) ......................................................................................... 28
TEMPERATURE RISE ......................................................................................................................................... 28
CIRCULATOR BLOWER SPEEDS ........................................................................................................................... 29
XV. Normal Sequence of Operation ................................................................................................................................ 29
POWER UP .....................................................................................................................................................
HEATING MODE ...............................................................................................................................................
COOLING MODE ..............................................................................................................................................
FAN ONLY MODE .............................................................................................................................................
29
29
30
30
XVI. Operational Checks .................................................................................................................................................. 30
BURNER FLAME ............................................................................................................................................... 30
XVII. Safety Circuit Description ....................................................................................................................................... 30
GENERAL ....................................................................................................................................................... 30
INTEGRATED CONTROL MODULE .......................................................................................................................... 31
PRIMARY LIMIT ................................................................................................................................................ 31
AUXILIARY LIMIT ............................................................................................................................................... 31
ROLLOUT LIMIT ................................................................................................................................................ 31
PRESSURE SWITCHES ........................................................................................................................................ 31
FLAME SENSOR ............................................................................................................................................... 31
XVIII. Troubleshooting ...................................................................................................................................................... 31
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS ................................................................................................. 31
DIAGNOSTIC CHART .......................................................................................................................................... 31
FAULT RECALL ................................................................................................................................................. 31
RESETTING FROM LOCKOUT ............................................................................................................................... 31
XIX. Maintenance ............................................................................................................................................................. 32
ANNUAL INSPECTION .......................................................................................................................................... 32
FILTERS .......................................................................................................................................................... 32
BURNERS ....................................................................................................................................................... 32
INDUCED DRAFT AND CIRCULATOR BLOWERS ......................................................................................................... 32
CONDENSATE TRAP AND DRAIN SYSTEM (QUALIFIED SERVICER ONLY) ...................................................................... 32
FLAME SENSOR (QUALIFIED SERVICER ONLY) ...................................................................................................... 32
IGNITER (QUALIFIED SERVICER ONLY) .................................................................................................................. 32
FLUE PASSAGES (QUALIFIED SERVICER ONLY) ..................................................................................................... 32
XX. Internal Filter Removal ............................................................................................................................................. 33
XXI. Before Leaving an Installation ................................................................................................................................ 33
XXII. Repair & Replacement Parts .................................................................................................................................. 33
Troubleshooting Charts ...................................................................................................................................... 34-35
Wiring Diagram ....................................................................................................................................................... 36
WARNING
G OODMAN
WILL NOT BE RESPONSIBLE FOR ANY INJURY OR PROPERTY
DAMAGE ARISING FROM IMPROPER SERVICE OR SERVICE PROCEDURES.
IF
YOU INSTALL OR PERFORM SERVICE ON THIS UNIT, YOU ASSUME
RESPONSIBILITY FOR ANY PERSONAL INJURY OR PROPERY DAMAGE WHICH
MAY RESULT.
M ANY
JURISDICTIONS REQUIRE A LICENSE TO INSTALL OR
SERVICE HEATING AND AIR CONDITIONING EQUIPMENT.
3
TO THE OWNER
WARNING
It is important that you fill out the owner’s registration card and mail
it today. This will assist us in contacting you should any service or
warranty information change in the future. When filling in the registration card, be sure to include the model, manufacturing, and serial
numbers, plus the installation date.
Your warranty certificate is also supplied with the unit. Read the
warranty carefully and note what is covered. Keep the warranty certificate in a safe location for future reference.
If additional information or operating instructions are required, contact the dealer where the purchase was made.
Homeowner Notice:
If the residence is left unattended for an extended period of time
(i.e., 4 hours or greater), have your heating system periodically
checked to ensure proper operation. Potential circumstances beyond our control such as power outages, gas service interruptions,
product installation, or component failures could result in heating
system operational problems.
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A
FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL
INJURY OR LOSS OF LIFE.
–
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.
–
WHAT TO DO IF YOU SMELL GAS:
• DO NOT TRY TO LIGHT ANY APPLIANCE.
• DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY
PHONE IN YOUR BUILDING.
• IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S
PHONE.
FOLLOW THE GAS SUPPLIER’S INSTRUCTIONS.
• IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE FIRE
DEPARTMENT.
– INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER,
SERVICE AGENCY OR THE GAS SUPPLIER.
TO THE INSTALLER
Before installing this unit, please read this manual thoroughly to familiarize yourself with specific items which must be adhered to, including but not limited to: unit maximum external static pressure,
gas pressures, BTU input rating, proper electrical connections, circulating air temperature rise, minimum or maximum CFM, and motor speed connections.
WARNING
SHOULD OVERHEATING OCCUR OR THE GAS SUPPLY FAIL TO SHUT OFF, TURN
OFF THE MANUAL GAS SHUTOFF VALVE EXTERNAL TO THE FURNACE BEFORE
TURNING OFF THE ELECTRICAL SUPPLY.
TRANSPORTATION DAMAGE
All units are securely packed in shipping containers tested according to International Safe Transit Association specifications. The carton must be checked upon arrival for external damage. If damage is
found, a request for inspection by carrier’s agent must be made in
writing immediately.
The furnace must be carefully inspected on arrival for damage and
bolts or screws which may have come loose in transit. In the event
of damage the consignee should:
1. Make a notation on delivery receipt of any visible damage to
shipment or container.
2. Notify carrier promptly and request an inspection.
3. With concealed damage, carrier must be notified as soon as
possible - preferably within five days.
4. File the claim with the following support documents within a
nine month statute of limitations.
CARBON MONOXIDE POISONING HAZARD
Special Warning for Installation of Furnace or Air Handling Units in
Enclosed Areas such as Garages, Utility Rooms or Parking Areas
Carbon monoxide producing devices (such as an automobile, space
heater, gas water heater, etc.) should not be operated in enclosed areas
such as unventilated garages, utility rooms or parking areas because of
the danger of carbon monoxide (CO) poisoning resulting from the exhaust
emissions. If a furnace or air handler is installed in an enclosed area such
as a garage, utility room or parking area and a carbon monoxide producing
device is operated therein, there must be adequate, direct outside
ventilation.
This ventilation is necessary to avoid the danger of CO poisoning which
can occur if a carbon monoxide producing device continues to operate in
the enclosed area. Carbon monoxide emissions can be (re)circulated
throughout the structure if the furnace or air handler is operating in any
mode.
•
Original or certified copy of the Bill of Lading, or indemnity
bond.
•
•
Original paid freight bill or indemnity in lieu thereof.
Original or certified copy of the invoice, showing trade and
other discounts or reductions.
•
Copy of the inspection report issued by carrier ’s
representative at the time damage is reported to carrier.
The carrier is responsible for making prompt inspection of damage
and for a thorough investigation of each claim. The distributor or
manufacturer will not accept claims from dealers for transportation
damage.
CO can cause serious illness including permanent brain damage or death.
B10259-216
Keep this literature in a safe place for future reference.
4
IDENTIFICATION
*
*
*
*
*
*
BLOWER COMPARTMENT
*
*
BURNER COMPARTMENT
COMPONENT
*
I.
Upflow/Horizontal
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Gas Valve
Gas Line Entrance (Alternate)
Pressure Switch
Gas Manifold
Combustion Air Intake Connection / “Coupling”
Hot Surface Igniter
Rollout Limit
Burners
Flame Sensor
Flue Pipe Connection / “Coupling”
Flue Pipe (Internal)
Primary Limit
Gas Line Entrance
Flue Pipe Connection (Alternate)
Rubber Elbow
Induced Draft Blower
Electrical Connection Inlets (Alternate)
18
19
20
21
22
23
24
25
26
27
28
29
30
31
5
Coil Front Cover Pressure Tap
Coil Front Cover Drain Port
Drain Line Penetrations
Drain Trap
Blower Door Interlock Switch
Capacitor
Integrated Control Module
(with fuse and diagnostic LED)
24-Volt Thermostat Connections
Transformer (40 VA)
Circulator Blower
Auxiliary Limit
Junction Box
Electrical Connection Inlets
Coil Front Cover
4. Discharge your body to ground before removing a new
control from its container. Follow steps 1 through 3 if
installing the control on a furnace. Return any old or new
controls to their containers before touching any ungrounded
object.
II. SAFETY
Please adhere to the following warnings and cautions when installing, adjusting, altering, servicing, or operating the furnace.
WARNING
III. PRODUCT APPLICATION
TO PREVENT PERSONAL INJURY OR DEATH DUE TO IMPROPER INSTALLATION,
ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE, REFER TO THIS
MANUAL.
This furnace is primarily designed for residential home-heating
applications. It is NOT designed or certified for use in mobile
homes, trailers or recreational vehicles. This unit is NOT designed
or certified for outdoor applications. The furnace must be installed
indoors (i.e., attic space, crawl space, or garage area provided the
garage area is enclosed with an operating door).
This furnace can be used in the following non-industrial commercial applications:
Schools, Office buildings, Churches, Retail stores
Nursing homes, Hotels/motels, Common or office areas
In such applications , the furnace must be installed with the following stipulations:
•
It must be installed per the installation instructions
provided and per local and national codes.
•
It must be installed indoors in a building constructed on
site.
•
It must be part of a ducted system and not used in a free
air delivery application.
•
It must not be used as a “make-up” air unit.
•
It must be installed with two-pipe systems for combustion
air, especially if VOC’s or other contaminants are present
in the conditioned space.
•
All other warranty exclusions and restrictions apply This
furnace is an ETL dual-certified appliance and is
appropriate for use with natural or propane gas (NOTE: If
using propane, a propane conversion kit is required).
Dual certification means that the combustion air inlet pipe is optional and the furnace can be vented as a:
Non-direct vent (single pipe) central forced air furnace in
which combustion air is taken from the installation area
or from air ducted from the outside or,
Direct vent (dual pipe) central forced air furnace in which
all combustion air supplied directly to the furnace burners
through a special air intake system outlined in these
instructions.
This furnace may be used as a construction site heater ONLY if the
following conditions are met:
•
The vent system is permanently installed per these
installation instructions.
•
A room thermostat is used to control the furnace. Fixed
jumpers that provide continuous heating CANNOT be
used.
•
Return air ducts are provided and sealed to the furnace.
•
A return air temperature range between 60ºF (16ºC) and
80ºF (27ºC) is maintained.
•
Air filters are installed in the system and maintained
during construction, replaced as appropriate during
construction, and upon completion of construction are
replaced.
•
The input rate and temperature rise are set per the furnace
rating plate.
•
100% outside air is provided for combustion air
requirements during construction. Temporary ducting can
be used.
FOR ADDITIONAL ASSISTANCE OR INFORMATION, CONSULT A
QUALIFIED INSTALLER, SERVICE AGENCY OR THE GAS SUPPLIER.
WARNING
THIS PRODUCT CONTAINS OR PRODUCES A CHEMICAL OR CHEMICALS WHICH
MAY CAUSE SERIOUS ILLNESS OR DEATH AND WHICH ARE KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER
REPRODUCTIVE HARM.
WARNING
TO PREVENT POSSIBLE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH
DUE TO ELECTRICAL SHOCK, THE FURNACE MUST BE LOCATED TO PROTECT
THE ELECTRICAL COMPONENTS FROM WATER.
WARNING
HEATING UNIT SHOULD NOT BE UTILIZED WITHOUT REASONABLE, ROUTINE,
INSPECTION, MAINTENANCE AND SUPERVISION. IF THE BUILIDNG IN WHICH ANY
SUCH DEVICE IS LOCATED WILL BE VACANT, CARE SHOULD BE TAKEN THAT
SUCH DEVICE IS ROUTINELY INSPECTED, MAINTAINED AND MONITORED. IN THE
EVENT THAT THE BUILDING MAYBE EXPOSED TO FREEZING TEMPERATURES
AND WILL BE VACANT, ALL WATER-BEARING PIPES SHOULD BE DRAINED, THE
BUILDING SHOULD BE PROPERLY WINTERIZED, AND THE WATER SOURCE
CLOSED. IN THE EVENT THAT THE BUILDING MAY BE EXPOSED TO FREEZING
TEMPERATURES AND WILL BE VACANT, ANY HYDRONIC COIL UNITS SHOULD
BE DRAINED AS WELL AND, IN SUCH CASE, ALTERNATIVE HEAT SOURCES
SHOULD BE UTILIZED.
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS
NOTE: Discharge static electricity accumulated in the body before
touching the unit. An electrostatic discharge can adversely affect
electrical components.
Use the following precautions during furnace installation and servicing to protect the integrated control module from damage. By
putting the furnace, the control, and the person at the same electrostatic potential, these steps will help avoid exposing the integrated
control module to electrostatic discharge. This procedure is applicable to both installed and non-installed (ungrounded) furnaces.
1. Disconnect all power to the furnace. Do not touch the
integrated control module or any wire connected to the control
prior to discharging your body’s electrostatic charge to
ground.
2. Firmly touch a clean, unpainted, metal surface of the
furnaces near the control. Any tools held in a person’s hand
during grounding will be discharged.
3. Service integrated control module or connecting wiring
following the discharge process in step 2. Use caution not
to recharge your body with static electricity; (i.e., do not move
or shuffle your feet, do not touch ungrounded objects, etc.).
If you come in contact with an ungrounded object, repeat
step 2 before touching control or wires.
6
•
•
NOTE: Do not connect the temporary duct directly to the
furnace. The duct must be sized according to the
instructions under Section V, Combustion and Ventilation
Air Requirements, Section 5.3.3.
The furnace heat exchanger, components, duct system,
air filters and evaporator coils are thoroughly cleaned
following final construction clean up.
All furnace operating conditions (including ignition, input
rate, temperature rise and venting) are verified according
to these installation instructions.
IV. LOCATION REQUIREMENTS & CONSIDERATIONS
GENERAL
WARNING
TO PREVENT POSSIBLE EQUIPMENT DAMAGE, PROPERTY DAMAGE, PERSONAL
INJURY OR DEATH, THE FOLLOWING BULLET POINTS MUST BE OBSERVED
WHEN INSTALLING THE UNIT.
Follow the instructions listed below when selecting a furnace location. Refer also to the guidelines provided in Section V, CombusNOTE: The Commonwealth of Massachusetts requires that the tion and Ventilation Air Requirements.
following additional requirements must also be met:
•
Centrally locate the furnace with respect to the proposed
or existing air distribution system.
•
Gas furnaces must be installed by a licensed plumber or
•
Ensure the temperature of the return air entering the
gas fitter.
furnace is between 55°F and 100°F when the furnace is
•
A T-handle gas cock must be used.
heating.
•
If the unit is to be installed in an attic, the passageway to
•
Provide
provisions for venting combustion products
and the service area around the unit must have flooring.
outdoors through a proper venting system. Special
consideration should be given to vent/flue pipe routing
To ensure proper installation and operation, thoroughly read this
and combustion air intake pipe when applicable. Refer
manual for specifics pertaining to the installation and application
to Section IX, Vent/Flue Pipe and Combustion Air Pipe of this product.
Termination Locations for appropriate termination
locations and to determine if the piping system from
WARNING
furnace to termination can be accomplished within the
guidelines given. NOTE: The length of flue and/or
combustion air piping can be a limiting factor in the
POSSIBLE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO FIRE,
EXPLOSION, SMOKE, SOOT, CONDENSTAION, ELECTRICAL SHOCK OR CARBON
location of the furnace.
MONOXIDE MAY RESULT FROM IMPROPER INSTALLATION, REPAIR, OPERATION,
•
Locate the furnace so condensate flows downwards to
OR MAINTENANCE OF THIS PRODUCT.
the drain. Do not locate the furnace or its condensate
drainage system in any area subject to below freezing
temperatures without proper freeze protection. Refer to
WARNING
Section X, Condensate Drain Lines and Trap for further
details.
TO PREVENT PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO FIRE,
•
Ensure adequate combustion air is available for the
DO NOT INSTALL THIS FURNACE IN A MOBILE HOME, TRAILER, OR RECREATIONAL
furnace. Improper or insufficient combustion air can
VEHICLE.
expose building occupants to gas combustion products
that could include carbon monoxide. Refer to Section V,
To ensure proper furnace operation, install, operate and maintain
Combustion and Ventilation Air Requirements.
the furnace in accordance with these installation and operation
•
Set the furnace on a level floor to enable proper
instructions, all local building codes and ordinances. In their abcondensate drainage. If the floor becomes wet or damp
sence, follow the latest edition of the National Fuel Gas Code
at times, place the furnace above the floor on a concrete
(NFPA 54/ANSI Z223.1), and/or CAN/CSA B149 Installation Codes,
base sized approximately 1-1/2" larger than the base of
local plumbing or waste water codes, and other applicable codes.
the furnace. Refer to the Section VII, Horizontal
A copy of the National Fuel Gas Code (NFPA 54/ANSI Z223.1) can
Applications and Considerations for leveling of horizontal
be obtained from any of the following:
furnaces.
American National Standards Institute
1430 Broadway
•
Ensure upflow or horizontal furnaces are not installed
New York, NY 10018
directly on carpeting, or any other combustible material.
The only combustible material allowed is wood.
National Fire Protection Association
•
Exposure to contaminated combustion air will result in
1 Batterymarch Park
safety and performance-related problems. Do not install
Quincy, MA 02269
the furnace where the combustion air is exposed to the
CSA International
following substances:
8501 East Pleasant Valley
chlorinated waxes or cleaners
Cleveland, OH 44131
chlorine-based swimming pool chemicals
A copy of the CAN/CSA B149 Installation Codes can also be obwater softening chemicals
tained from:
deicing salts or chemicals
CSA International
carbon tetrachloride
178 Rexdale Boulevard
halogen type refrigerants
Etobicoke, Ontario, Canada M9W 1R3
cleaning solutions (such as perchloroethylene)
The rated heating capacity of the furnace should be greater than or
printing inks
equal to the total heat loss of the area to be heated. The total heat
loss should be calculated by an approved method or in accordance with “ASHRAE Guide” or “Manual J-Load Calculations” published by the Air Conditioning Contractors of America.
7
•
•
•
•
paint removers
varnishes
hydrochloric acid
cements and glues
antistatic fabric softeners for clothes dryers
and masonry acid washing materials
Seal off a non-direct vent furnace if it is installed near an
area frequently contaminated by any of the above
substances. This protects the non-direct vent furnace
from airborne contaminants. To ensure that the
enclosed non-direct vent furnace has an adequate supply
of combustion air, vent from a nearby uncontaminated
room or from outdoors. Refer to the Section V,
Combustion and Ventilation Air Requirements for details.
If the furnace is used in connection with a cooling unit,
install the furnace upstream or in parallel with the cooling
unit. Premature heat exchanger failure will result if the
cooling unit is placed ahead of the furnace.
If the furnace is installed in a residential garage, position
the furnace so that the burners and ignition source are
located not less than 18 inches (457 mm) above the floor.
Protect the furnace from physical damage by vehicles.
If the furnace is installed horizontally, the furnace access
doors must be vertical so that the burners fire horizontally
into the heat exchanger. Do not install the unit with the
access doors on the “up/top” or “down/bottom” side of
the furnace.
FURNACE SUSPENSION
If suspending the furnace from rafters or joists, use 3/8" threaded
rod and 2”x2”x1/8” angle iron as shown below. The length of rod
will depend on the application and the clearances necessary.
PROVIDE 8" MINMUM CLEARANCE BETWEEN
CENTER ROD AND FURNACE CABINET
TO ALLOW FOR CIRCULATOR BLOWER REMOVAL
3/8" DIAMETER
ASSURE FURNACE IS LEVEL FROM
THREADED ROD
END TO END AND HAS A SLIGHT
(6 PLACES)
FORWARD TILT WITH THE FRONT
OF THE FURNACE 0"-3/4"
BELOW THE BACK OF THE FURNACE
HOLD DOWN
NUTS
SUPPORT
NUTS
2"X2"X1/8" ANGLE IRON
(3 PLACES)
POSITION AS CLOSE AS POSSIBLE
TO BLOWER DECK TO ALLOW FOR
TILT OUTWARD TO ALLOW FOR
DOOR AND CIRCULATOR BLOWER
CIRCULATOR BLOWER REMVOAL
REMOVAL
Suspended Furnace
EXISTING FURNACE REMOVAL
NOTE: When an existing furnace is removed from a venting system
serving other appliances, the venting system may be too large to
properly vent the remaining attached appliances.
The following vent testing procedure is reproduced from the American
National Standard/National Standard of Canada for Gas-Fired Central Furnaces ANSI Z21.47-Latest Edition, CSA-2.3-Latest Edition
Section 1.23.1.
CLEARANCES AND ACCESSIBILITY
Installations must adhere to the clearances to combustible materials to which this furnace has been design certified. The minimum clearance information for this furnace is provided on the unit’s
clearance label. These clearances must be permanently maintained. Clearances must also accommodate an installation’s gas,
electrical, and drain trap and drain line connections. If the alternate
vent/flue connection is used, additional clearance must be provided to accommodate these connections. Refer to Section IX,
Vent Flue Pipe and Combustion Air Pipe for details. NOTE: In
addition to the required clearances to combustible materials, a
minimum of 24 inches service clearance must be available in front
of the unit.
The following steps shall be followed with each appliance connected to the
venting system placed in operation, while any other appliances connected to the venting system are not in operation:
a. Seal any unused openings in the venting system;
b. Inspect the venting system for proper size and horizontal pitch, as
required by the National Fuel Gas Code, ANSI Z223.1 or the CSA
B149 Installation Codes and these instructions. Determine that there
is no blockage or restriction, leakage, corrosion and other deficiencies which could cause an unsafe condition;
c. In so far as practical, close all building doors and windows and all
doors between the space in which the appliance(s) connected to the
venting system are located and other spaces of the building. Turn on
clothes dryers and any appliance not connected to the venting system. Turn on any exhaust fans, such as range hoods and bathroom
exhausts, so they shall operate at maximum speed. Do not operate a
summer exhaust fan. Close fireplace dampers;
d. Follow the lighting instructions. Place the appliance being inspected
in operation. Adjust thermostat so appliance shall operate continuously;
BOTTOM
BOTTOM
e. Test for draft hood equipped spillage at the draft hood relief opening
after 5 minutes of main burner operation. Use the flame of a match
or candle;
A furnace installed in a confined space (i.e., a closet or utility room)
must have two ventilation openings with a total minimum free area
of 0.25 square inches per 1,000 BTU/hr of furnace input rating.
Refer to the Product Data Book applicable to your model for minimum clearances to combustible surfaces. One of the ventilation
openings must be within 12 inches of the top; the other opening
must be within 12 inches of the bottom of the confined space. In a
typical construction, the clearance between the door and door frame
is usually adequate to satisfy this ventilation requirement.
f. After it has been determined that each appliance connected to the
venting system properly vents when tested as outlined above, return doors, windows, exhaust fans, fireplace dampers and any other
gas burning appliance to their previous conditions of use;
g. If improper venting is observed during any of the above tests, the
common venting system must be corrected.
8
If this furnace is to be installed in the same space with other gas
appliances, such as a water heater, ensure there is an adequate
supply of combustion and ventilation air for the other appliances.
Refer to the latest edition of the National Fuel Gas Code NFPA 54/
ANSI Z223.1 (Section 5.3), or CSA B149 Installation Codes (Sections 7.2, 7.3, or 7.4), or applicable provisions of the local building
codes for determining the combustion air requirements for the
appliances.
Most homes will require outside air be supplied to the furnace area
by means of ventilation grilles or ducts connecting directly to the
outdoors or spaces open to the outdoors such as attics or crawl
spaces.
The following information on air for combustion and ventilation is reproduced from the National Fuel Gas Code NFPA 54/ANSI Z223.1 Section
5.3.
5.3.1 General:
(a) The provisions of 5.3 apply to gas utilization equipment installed in
buildings and which require air for combustion, ventilation and dilution of flue gases from within the building. They do not apply to (1)
direct vent equipment which is constructed and installed so that all
air for combustion is obtained from the outside atmosphere and all
flue gases are discharged to the outside atmosphere, or (2) enclosed
furnaces which incorporate an integral total enclosure and use only
outside air for combustion and dilution of flue gases.
Corrections must be in accordance with the latest edition of the
National Fuel Gas Code NFPA 54/ANSI Z223.1 and/or CSA B149
Installation Codes.
If resizing is required on any portion of the venting system, use the
appropriate table in Appendix G in the latest edition of the National
Fuel Gas Code ANSI Z223.1 and/or CSA B149 Installation Codes.
THERMOSTAT LOCATION
The thermostat should be placed approximately five feet from the
floor on a vibration-free, inside wall in an area having good air
circulation. Do not install the thermostat where it may be influenced by any of the following:
•
Drafts, or dead spots behind doors, in corners, or under
cabinets.
•
•
•
•
•
•
Hot or cold air from registers.
Radiant heat from the sun.
Light fixtures or other appliances.
Radiant heat from a fireplace.
Concealed hot or cold water pipes, or chimneys.
Unconditioned areas behind the thermostat, such as an
outside wall.
(b) Equipment shall be installed in a location in which the facilities for
ventilation permit satisfactory combustion of gas, proper venting
and the maintenance of ambient temperature at safe limits under
normal conditions of use. Equipment shall be located so as not to
interfere with proper circulation of air. When normal infiltration
does not provide the necessary air, outside air shall be introduced.
DRAFTS OR DEAD SPOTS
-BEHIND DOORS
-IN CORNERS
-UNDER CABINETS
(c) In addition to air needed for combustion, process air shall be provided as required for: cooling of equipment or material, controlling
dew point, heating, drying, oxidation or dilution, safety exhaust,
odor control, and air for compressors.
HOT
COLD
(d) In addition to air needed for combustion, air shall be supplied for
ventilation, including all air required for comfort and proper working
conditions for personnel.
Thermostat Influences
Consult the instructions packaged with the thermostat for mounting instructions and further precautions.
(e) While all forms of building construction cannot be covered in detail,
air for combustion, ventilation and dilution of flue gases for gas
utilization equipment vented by natural draft normally may be obtained by application of one of the methods covered in 5.3.3 and
5.3.4.
V. COMBUSTION & VENTILATION AIR REQUIREMENTS
WARNING
(f) Air requirements for the operation of exhaust fans, kitchen ventilation systems, clothes dryers, and fireplaces shall be considered in
determining the adequacy of a space to provide combustion air
requirements.
5.3.2 Equipment Located in Unconfined Spaces:
In unconfined spaces (see definition below) in buildings, infiltration may
be adequate to provide air for combustion ventilation and dilution of
flue gases. However, in buildings of tight construction (for example,
weather stripping, heavily insulated, caulked, vapor barrier, etc.), additional air may need to be provided using the methods described in 5.3.3b or 5.3.4.
POSSIBLE PROPERTY DAMAGE PERSONAL INJURY OR DEATH MAY OCCUR IF
THE FURNACE IS NOT PROVIDED WITH ENOUGH FRESH AIR FOR PROPER
COMBUSTION AND VENTILATION OF FLUE GASES. MOST HOMES REQUIRE
OUTSIDE AIR BE SUPPLIED TO THE FURNACE AREA.
Improved construction and additional insulation in buildings have
reduced heat loss by reducing air infiltration and escape around
doors and windows. These changes have helped in reducing
heating/cooling costs but have created a problem supplying combustion and ventilation air for gas fired and other fuel burning appliances. Appliances that pull air out of the house (clothes dryers,
exhaust fans, fireplaces, etc.) increase the problem by starving Space, Unconfined.
For purposes of this Code, a space whose volume is not less than 50
appliances for air.
cubic feet per 1,000 BTU per hour of the aggregate input rating of all
House depressurization can cause back drafting or improper comappliances installed in that space. Rooms communicating directly with
bustion of gas-fired appliances, thereby exposing building occuthe space in which the appliances are installed through openings not
pants to gas combustion products that could include carbon monfurnished with doors, are considered a part of the unconfined space.
oxide.
9
5.3.3 Equipment Located in Confined Spaces:
Chimney or Gas Vent
Ventilation louvers
(each end of attic)
(a) All Air from Inside the Building: The confined space shall be provided with two permanent openings communicating directly with
an additional room(s) of sufficient volume so that the combined
volume of all spaces meets the criteria for an unconfined space. The
total input of all gas utilization equipment installed in the combined
space shall be considered in making this determination. Each opening shall have a minimum free area of 1 square inch per 1,000 BTU
per hour of the total input rating of all gas utilization equipment in
the confined space, but not less than 100 square inches. One opening shall be within 12 inches of the top and one within 12 inches of
the bottom of the enclosure.
NOTE: The inlet and outlet air
openings must each have a free
area of not less than one square
inch per 4000 BTU of the
total input rating of all equipment
in the enclosure.
Outlet Air
Furnace
Water
Heater
Inlet air duct
[ends 1 ft (300 mm)
above floor]
Chimney or Gas Vent
NOTE: Each opening must have
a free area of not less than one
square inch per 1000 BTU of
the total input rating of all equipment in the enclosure, but not
less than 100 square inches.
Equipment Located in Confined Spaces; All Air from Outdoors
Through Ventilated Attic. See 5.3.3-b.
3. When communicating with the outdoors through horizontal ducts,
each opening shall have a minimum free area of 1 square inch per
2,000 BTU per hour of total input rating of all equipment in the
enclosure.
Opening
Furnace
Water
Heater
Chimney or Gas Vent
Opening
Equipment Located in Confined Spaces; All Air from Inside
Building. See 5.3.3-a.
Outlet air duct
(b) All Air from Outdoors: The confined space shall be provided with
two permanent openings, one commencing within 12 inches of the
top and one commencing within 12 inches of the bottom of the
enclosure. The openings shall communicate directly, or by ducts,
with the outdoors or spaces (crawl or attic) that freely communicate
with the outdoors.
1. When directly communicating with the outdoors, each opening
shall have a minimum free area of 1 square inch per 4,000 BTU
per hour of total input rating of all equipment in the enclosure.
Furnace
Water
Heater
Inlet air duct
*If the appliance room is located against an outside wall and the air openings communicate directly with the
outdoors, each opening shall have a free area of not less than one square inch per 4,000 BTU per hour of
the total input rating of all appliances in the enclosure.
Equipment Located in Confined Spaces; All Air from Outdoors.
See 5.3.3-b.
Chimney or Gas Vent
Ventilation louvers
(each end of attic)
4. When ducts are used, they shall be of the same cross-sectional
area as the free area of the openings to which they connect. The
minimum dimension of rectangular air ducts shall not be less
than 3 inches.
NOTE: The inlet and outlet air
openings must each have a free
area of not less than one square
inch per 4000 BTU of the
total input rating of all equipment
in the enclosure.
NOTE: The single opening must have
a free area of not less than one
square inch per 3000 BTU of
the total input rating of all equipment in the enclosure, but not less than
the sum of the areas of all vent
connectors in the confined space.
Outlet Air
Furnace
NOTE: The air duct openings
must have a free area of not
less than one square inch per
2000 BTU of the total input
rating of all equipment in the
enclosure*.
Water
Heater
Inlet Air
Chimney or Gas Vent
Alternate
air inlet
Opening
Ventilation louvers for
unheated crawl space
Equipment Located in Confined Spaces; All Air from Outdoors—
Inlet Air from Ventilated Crawl Space and Outlet Air to Ventilated
Attic. See 5.3.3-b
2. When communicating with the outdoors through vertical ducts,
each opening shall have a minimum free area of 1 square inch per
4,000 BTU per hour of total input rating of all equipment in the
enclosure.
10
Furnace
Water
Heater
Alternate
Opening
Location
Equipment Located in Confined Spaces; All Air from Outdoors Single Air Opening. See 5.3.3-b.
5. When directly communicating with the outdoors, the single opening shall have a minimum free area of 1 square inch per 3,000
BTU per hour of total input rating of all equipment in the enclosure.
LOCATION
5.3.4 Specially Engineered Installations:
The requirements of 5.3.3 shall not necessarily govern when special
engineering, approved by the authority having jurisdiction, provides an
adequate supply of air for combustion, ventilation, and dilution of flue
gases.
5.3.5 Louvers and Grilles:
In calculating free area in 5.3.3, consideration shall be given to the blocking effect of louvers, grilles or screens protecting openings. Screens used
shall not be smaller than 1/4 inch mesh. If the area through a design of
louver or grille is known, it should be used in calculating the size of
opening required to provide the free area specified. If the design and free
area is not known, it may be assumed that wood louvers will have 20-25
percent free area and metal louvers and grilles will have 60-75 percent
Horizontal Furnace
free area. Louvers and grilles shall be fixed in the open position or
interlocked with the equipment so that they are opened automatically DRAIN TRAP AND LINES
during equipment operation.
In horizontal applications the condensate drain trap is secured to
5.3.6 Special Conditions Created by Mechanical Exhausting or Fire- the furnace side panel, suspending it below the furnace. A minimum clearance of 4 3/4 inches below the furnace must be proplaces:
vided for the drain trap. Additionally, the appropriate downward
Operation of exhaust fans, ventilation systems, clothes dryers, or fire- piping slope must be maintained from the drain trap to the drain
places may create conditions requiring special attention to avoid unsat- location. Refer to Section X, Condensate Drain Trap and Lines for
isfactory operation of installed gas utilization equipment. Air from further details. If the drain trap and drain line will be exposed to
Inside Building. See 5.3.3-a.
temperatures near or below freezing, adequate measures must
be taken to prevent condensate from freezing.
VI. INSTALLATION POSITIONS
This furnace may be installed in an upright position or horizontal
on either the left or right side panel. Do not install this furnace on
its back. For upright upflow furnaces, return air ductwork may be
attached to the side panel(s) and/or basepan. For horizontal upflow
furnaces, return air ductwork must be attached to the basepan.
NOTE: Ductwork must never be attached to the back of the furnace.
Contact your distributor for proper airflow requirements and number of required ductwork connections. Refer to “Recommended
Installation Positions” figure for appropriate installation positions,
ductwork connections, and resulting airflow arrangements.
VII. HORIZONTAL APPLICATIONS & CONSIDERATIONS
LEVELING
Leveling ensures proper condensate drainage from the heat exchanger and induced draft blower. For proper flue pipe drainage,
the furnace must be level lengthwise from end to end. The furnace
should also be level from back to front or have a slight tilt with the
access doors downhill (approximately 3/4 inches) from the back
panel. The slight tilt allows the heat exchanger condensate, generated in the recuperator coil, to flow forward to the recuperator coil
front cover.
ALTERNATE VENT/FLUE CONNECTIONS
In horizontal installations provisions for alternate flue piping are
available for upflow furnaces with left discharge. This configuraHorizontal applications, in particular, may dictate many of the tion allows the flue piping to be run vertically through the furnace.
installation’s specifics such as airflow direction, ductwork connec- Refer to the “Recommended Installation Positions” figure for furtions, flue and combustion air pipe connections, etc. The basic ther detail. The standard piping connections may also be used in
application of this furnace as a horizontal furnace differs only slightly these positions. Refer to Section IX, Vent/Flue Pipe and Combusfrom an upright installation. When installing a furnace horizontally, tion Air Pipe for details concerning the conversion to the alternate
additional consideration must be given to the following:
vent/flue connections.
GENERAL
11
VIII. PROPANE GAS /HIGH ALTITUDE INSTALLATIONS
WARNING
POSSIBLE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH MAY OCCUR IF
THE CORRECT CONVERSION KITS ARE NOT INSTALLED. THE APPROPRIATE KITS
MUST BE APPLIED TO INSURE SAFE AND PROPER FURNACE OPERATION. ALL
CONVERSIONS MUST BE PERFORMED BY A QUALIFIED INSTALLER OR SERVICE
AGENCY.
This furnace is shipped from the factory configured for natural gas
at standard altitude. Propane gas installations require an orifice
change to compensate for the energy content difference between
natural and propane gas.
High altitude installations may require both a pressure switch and
an orifice change. These changes are necessary to compensate
for the natural reduction in the density of both the gas fuel and the
combustion air at higher altitude.
For installations above 7000 feet, please refer to your distributor
for required kit(s).
HIGH ALTITUDE GAS ORIFICE CHART
Altitude
Gas
Kit
Orifice
Manifold
Pressure
Natural
None
#43
3.5" w.c.
Propane
LPT-00A
#55
10.0" w.c.
0-7000
Pressure
Switch
None
NOTE: In Canada, gas furnaces are certified to 4500 feet.
Contact the distributor for a tabular listing of appropriate
manufacturer’s kits for propane gas and/or high altitude installations. The indicated kits must be used to insure safe and proper
furnace operation. All conversions must be performed by a qualified installer, or service agency.
IX. VENT/FLUE PIPE & COMBUSTION AIR PIPE
GENERAL
WARNING
Recommended Installation Positions
NOTE: Alternate “vertical” piping connections can not be used when
an upflow furnace is installed with supply air discharging to the
right. Use the standard flue and combustion air piping connections.
FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN BODILY INJURY OR
CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS GIVEN IN THIS
DEATH.
SECTION.
ALTERNATE ELECTRICAL AND GAS LINE CONNECTIONS
WARNING
This furnace has provisions allowing for electrical and gas line
connections through either side panel. In horizontal applications
the connections can be made either through the “top” or “bottom” of
the furnace.
UPON COMPLETION OF THE FURNACE INSTALLATION, CAREFULLY INSPECT THE
ENTIRE FLUE SYSTEM BOTH INSIDE AND OUTSIDE THE FURNACE TO ASSURE IT
IS PROPERLY SEALED.
DRAIN PAN
A drain pan must be provided if the furnace is installed above a
conditioned area. The drain pan must cover the entire area under
the furnace (and air conditioning coil if applicable).
FREEZE PROTECTION
Refer to Section VII, Horizontal Applications and Conditions - Drain
Trap and Lines.
FURNACE SUSPENSION
LEAKS IN THE FLUE SYSTEM CAN RESULT IN SERIOUS
PERSONAL INJURY OR DEATH DUE TO EXPOSURE TO FLUE PRODUCTS,
INCLUDING CARBON MONOXIDE.
A condensing gas furnace achieves its high level of efficiency by
extracting almost all of the heat from the products of combustion
and cooling them to the point where condensation takes place.
Because of the relatively low flue gas temperature and water condensation requirements, PVC pipe is used as venting material.
This furnace must not be connected to Type B, BW, or L vent or vent
connector, and must not be vented into any portion of a factory built
or masonry chimney except when used as a pathway for PVC as
described later in this section. Never common vent this appliance
with another appliance or use a vent which is used by a solid fuel
appliance. Do not use commercially available “no hub connectors” other than those shipped with this product.
If the furnace is installed in a crawl space it must be suspended
from the floor joist or supported by a concrete pad. Never install the
furnace on the ground or allow it to be exposed to water. Refer to
Section IV, Location Requirements and Considerations - Furnace
Suspension for further details.
12
It is the responsibility of the installer to follow the manufacturers’
recommendations and to verify that all vent/flue piping and connectors are compatible with furnace flue products. Additionally, it
is the responsibility of the installer to ensure that all piping and
connections possess adequate structural integrity and support to
prevent flue pipe separation, shifting, or sagging during furnace
operation.
TERMINATION LOCATIONS
NOTES: Refer to Section IV, Location Requirements and
Considerations for combustion air contaminant restrictions.
The following bullets and diagram describe the restrictions concerning the appropriate location of vent/flue pipe and combustion
air intake pipe (when applicable) terminations. Refer to Non-Direct Vent (Single Pipe) Piping and Direct Vent (Dual Pipe) Piping
located in this section for specific details on termination construction.
•
All terminations (flue and/or intake) must be located at
least 12 inches above ground level or the anticipated
snow level.
•
Vent terminations (non-direct and direct vent) must
terminate at least 3 feet above any forced air inlet located
within 10 feet.
NOTE: This provision does not apply to the combustion
air intake termination of a direct vent application.
•
The vent termination of a non-direct vent application must
terminate at least 4 feet below, 4 feet horizontally from, or
1 foot above any door, window, or gravity air inlet into any
building.
•
The vent termination of a direct vent application must
terminate at least 12 inches from any opening through
which flue gases may enter a building (door, window, or
gravity air inlet).
•
The vent termination of vent pipe run vertically through a
roof must terminate at least 12 inches above the roof line
(or the anticipated snow level) and be at least 12 inches
from any vertical wall (including any anticipated snow
build up).
•
A vent termination shall not terminate over public walkways
or over an area where condensate or vapor could create
a nuisance or hazard or could be detrimental to the
operation of regulators, relief valves, or other equipment.
•
The combustion air intake termination of a direct vent
application should not terminate in an area which is
frequently dusty or dirty.
DUAL CERTIFICATION: NON-DIRECT/DIRECT VENT
This furnace is dual certified and may be installed as a non-direct
vent (single pipe) or direct vent (dual pipe) appliance. A non-direct
vent installation requires only a vent/flue pipe, while a direct vent
installation requires both a vent/flue pipe and a combustion air
intake pipe. Refer to the appropriate section for details concerning
piping size, length, number of elbows, furnace connections, and
terminations.
MATERIALS AND JOINING METHODS
WARNING
TO AVOID BODILY INJURY, FIRE OR EXPLOSION, SOLVENT CEMENTS MUST BE
KEPT AWAY FROM ALL IGNITION SOURCES (I.E., SPARKS, OPEN FLAMES, AND
EXCESSIVE HEAT) AS THEY ARE COMBUSTIBLE LIQUIDS.
AVOID BREATHING
CEMENT VAPORS OR CONTACT WITH SKIN AND/OR EYES.
Two- or three-inch nominal diameter PVC Schedule 40 pipe meeting ASTM D1785, PVC primer meeting ASTM F656, and PVC solvent cement meeting ASTM D2564 specifications must be used.
Fittings must be DWV type fittings meeting ASTM D2665 and ASTM
D3311. Carefully follow the manufacturer’s instructions for cutting,
cleaning, and solvent cementing of PVC.
As an alternative to PVC pipe, primer, solvent cement, and fittings,
ABS materials which are in compliance with the following specifications may be used. Two-or-three-inch ABS Schedule 40 pipe
must meet ASTM D1527 and, if used in Canada, must be CSA
listed. Solvent cement for ABS to ABS joints must meet ASTM
D2235 and, if used in Canada, must be CSA listed. The solvent
cement for the PVC to ABS transition joint must meet ASTM D3138.
Fittings must be DWV type fittings meeting ASTM D2661 and ASTM
D3311 and, if used in Canada, must be CSA listed. Carefully
follow the pipe manufacturers’ instructions for cutting, cleaning,
and solvent cementing PVC and/or ABS.
All 90° elbows must be medium radius (1/4 bend DWV) or long
radius (Long sweep 1/4 bend DWV) types conforming to ASTM
D3311. A medium radius (1/4 bend DWV) elbow measures 3 1/
16” minimum from the plane of one opening to the centerline of the
other opening for 2” diameter pipe, and 4 9/16” minimum for 3”
pipe.
Non-Direct Vent
&
Direct Vent
Vent/Flue Terminations
Non-Direct Vent
Vent/Flue Termination
No Terminations
Above Walkway
<10'
3' min.
PROPER VENT/FLUE AND COMBUSTION AIR PIPING PRACTICES
Adhere to these instructions to ensure safe and proper furnace
performance. The length, diameter, and number of elbows of the
vent/flue pipe and combustion air pipe (when applicable) affects
the performance of the furnace and must be carefully sized. All
piping must be installed in accordance with local codes and these
instructions.
Piping must be adequately secured and supported to prohibit sagging, joint separation, and/or detachment from the furnace. Horizontal runs of vent/flue piping must be supported every three feet
and must maintain a 1/4 inch per foot downward slope, back towards the furnace, to properly return condensate to the furnace’s
drain system. Allowances should be made for minor expansion
and contraction due to temperature variations. For this reason,
particular care must be taken to secure piping when a long run is
followed by a short offset of less than 40 inches.
4' min.
12"
4'
min.
12"
min.
Grade or Highest
Anticipated
Snow Level
12" min.
12" min.
Forced Air
Inlet
Non-Direct Vent
Vent/Flue Termination
Direct Vent
Vent/Flue Termination
Vent Termination Clearances
NOTE: In Canada, the Canadian Fuel Gas Code takes precedence
over the preceding termination restrictions.
13
COMBUSTION AIR PIPE
CANADIAN VENTING REQUIREMENTS
DIRECT VENT INSTALLATIONS
In Canada, venting must conform to the requirements of the current CAN/CSA-B149 Installation Code. Use only CSA listed two or
three inch diameter PVC or ABS pipe, solvent cement, and fittings
throughout. Carefully follow the pipe manufacturers’ instructions
for cutting, cleaning, and solvent cementing PVC and/or ABS.
The vent can be run through an existing unused chimney provided
the space between the vent pipe and the chimney is insulated and
closed with a weather-tight, corrosion-resistant flashing.
On upflow units secure the combustion air intake pipe directly to
the air intake coupling. NOTE: Because of probable material conflicts, do not use other commercially available “no hub connectors”.
NON-DIRECT VENT INSTALLATIONS
A minimum of one 90° elbow should be installed on the combustion air intake “coupling” to guard against inadvertent blockage.
STANDARD FURNACE CONNECTIONS
COMBUSTION
AIR PIPE
(DIRECT VENT ONLY)
It is the responsibility of the installer to ensure that the piping
connections to the furnace are secure, airtight, and adequately
supported.
As shipped, attachment “couplings” for vent/flue and combustion
air intake pipe connections are provided on the furnace’s top cover
(upflow). To use the standard connections, field supplied vent/flue
pipe and combustion air intake pipe (when applicable) should be
secured directly to the furnace at these locations.
90 PVC
ELBOW
(NON-DIRECT VENT)
OR
VENT/FLUE PIPE
Vent/flue pipe can be secured to the vent/flue coupling using the
rubber coupling and worm gear hose clamps provided with this
furnace (see “Standard Connections” figure). The rubber coupling
allows separation of the vent/flue pipe from the furnace during
servicing. Combustion Air and Vent piping should be routed in a
manner to avoid contact with refrigerant lines, metering devices,
condensate drain lines, etc. If necessary, clearances may be
increased by utilizing two 45 deg. Long-Sweep Elbows and creating an “S” joint to provide additional space at connection locations. This joint can be rotated on the fitting to establish maximum clearance between refrigerant lines, metering devices, and
condensate drain lines, etc. This joint is the equivalent of one 90
deg. elbow when considering elbow count.
STANDARD CONNECTIONS
ALTERNATE FURNACE CONNECTIONS
If the standard locations are undesirable for a specific installation,
alternate side panel locations are available for vent/flue pipe connections. These locations may be of particular benefit to upright
upflow installations requiring additional access to an A coil, or to
horizontal installations desiring vent/flue piping run vertically from
the side of the cabinet.
NOTE: Standard and alternate locations can be combined (i.e., an
installation may use the standard combustion air intake location
but use the alternate vent/flue location), if needed.
V
E
N
T
WARNING
EDGES OF SHEET METAL HOLES MAY BE SHARP. USE GLOVES AS A PRECAUTION WHEN REMOVING HOLE PLUGS.
45 DEGREE
LONG-SWEEP
ELBOWS
ALTERNATE VENT/FLUE LOCATION
The alternate vent/flue location is the large hole directly in line with
the induced draft blower outlet. To use the alternate vent/flue location refer to the following steps, the “Vent/Flue Pipe Cuts” figure,
and the “Alternate Vent/Flue Location” figure.
1. Remove and save the four screws securing the vent/flue
coupling to the furnace top panel.
2. Loosen the worm gear hose clamps on the rubber elbow
and detach it from both the induced draft blower and the
vent/flue pipe.
3. Remove the vent/flue pipe from the furnace.
4. Cut the vent/flue pipe 3.75 inches from the flanged end of
the pipe. See Vent/Flue Pipe Cuts figure. The section of
pipe attached to the coupling will reach through the side
panel to the induced draft blower. Discard remaining pipe
and elbows.
Increased Clearance Configuration
NOTE: Do not use other commercially available “no hub connectors” due to possible material conflicts. The vent/flue pipe can
also be secured using a PVC or ABS elbow or coupling using the
appropriate glue (see Section IX, Materials and Joining Methods).
NOTE: For non-direct vent installations, a minimum of one 90°
elbow should be installed on the combustion air intake coupling
to guard against inadvertent blockage.
14
6
SECURE TO
ID BLOWER WITH
RUBBER COUPLING
AND HOSE
CLAMPS
FLANGE
3.75"
CUT HERE
5. Remove plastic plug from alternate vent/flue location.
Relocate and install plug in standard vent/flue location (top
cover).
6. Insert cut section of vent/flue pipe and coupling into alternate
vent/flue location. Using a rubber coupling and worm gear
hose clamps from the drain kit bag, attach the vent/flue pipe
and coupling to the induced draft blower. Secure the
coupling to the cabinet using the screws removed in step 1
or with field-supplied 3/8” #8 self drilling screws.
WARNING
THE RUBBER ELBOW IS NOT DESIGNED TO SUPPORAT A LOAD. WHEN THE
RUBBER ELBOW IS MOUNTED EXTERNALLY TO THE FURNACE CABINET,
EXTREME CARE MUST BE TAKEN TO ADEQUATELY SUPPORT FIELD-SUPPLIED
VENT/FLUE PIPING, AS DAMAGE CAN RESULT IN LEAKS CAUSING BODILY
INJURY OR DEATH DUE TO EXPOSURE TO FLUE GASES, INCLUDING CARBON
MONOXIDE.
7. For upright installations, externally mount the rubber elbow
to the vent/flue coupling using a worm gear hose clamp.
Secure field supplied vent/flue piping to the rubber elbow
using a worm gear hose clamp. NOTE: Use of the alternate
vent/flue location for upright installations, requires the drain
trap be installed on the same side of the unit as the flue
pipe.
8. For horizontal installations, externally secure the fieldsupplied vent/flue pipe directly to the vent/flue coupling using
a PVC or ABS coupling or elbow.
3
REMOVE
PIPE
1
REMOVE
4 SCREWS
6
SECURE TO
CABINET WITH
SCREWS
UPFLOW/HORIZONTAL
Alternate Vent/Flue Location
NON-DIRECT VENT (SINGLE PIPE) PIPING
Non-direct vent installations require only a vent/flue pipe. The vent
pipe can be run horizontally with an exit through the side of the
building or run vertically with an exit through the roof of the building.
The vent can also be run through an existing unused chimney;
however, it must extend a minimum of 12 inches above the top of
the chimney. The space between the vent pipe and the chimney
must be closed with a weather-tight, corrosion-resistant flashing.
For details concerning connection of the vent/flue pipe to the furnace, refer to Section IX, Vent/Flue Pipe and Combustion Air Standard Furnace Connections or Alternate Furnace Connections
for specific details. Refer to the following Non-Direct Vent (Single
Pipe) Piping - Vent/Flue Pipe Terminations for specific details on
termination construction.
Although non-direct vent installations do not require a combustion
air intake pipe, a minimum of one 90° elbow should be attached to
the furnace’s combustion air intake if: an upright installation uses
the standard intake location. This elbow will guard against inadvertent blockage of the air intake.
VENT/FLUE PIPE LENGTHS
AND
DIAMETERS
Refer to the following table for applicable length, elbows, and pipe
diameter for construction of the vent/flue pipe system of a nondirect vent installation. In addition to the vent/flue pipe, a single 90°
elbow should be secured to the combustion air intake to prevent
inadvertent blockage. The tee used in the vent/flue termination
must be included when determining the number of elbows in the
piping system.
5
REMOVE
AND RELOCATE
2
DETACH RUBBER
ELBOW FROM
ID BLOWER AND
VENT/FLUE
PIPE
UPFLOW
15
90º
MEDIUM RADIUS
ELBOWS
Non-Direct Vent (Single Pipe)
(1) (2)
Maximum Allowable Length of Vent/Flue Pipe (ft)
Pipe
Number of Elbows (3) (5)
Models
Size (4)
(kBtu_Tons)
(inc.)
2
3
4
5
6
7
045_3
2
68
65
62
59
56
53
50
070_3
2
68
65
62
59
56
53
50
070_4
2
46
43
40
2
16
13
10
3
68
65
62
59
56
53
50
090_5
3
68
65
62
59
56
53
50
115_5
3
68
65
62
59
56
53
50
090_4
12" MIN.
TO ROOF OR
HIGHEST
ANTICIPATED
SNOW LEVEL
8
Not Recommended
Alternate Vertical Termination (Single Pipe)
WALL
OUTSIDE
INSIDE
TEE
or
90°ELBOW
TURNED
DOWN
1) One 90° elbow should be secured to the combustion air intake connection.
2) Minimum requirement for each vent pipe is five (5) feet in length and
one elbow/tee.
3) Tees and/or elbows used in the vent/flue termination must be included
when determining the number of elbows in the piping system.
4) 3” diameter pipe can be used in place of 2” diameter pipe.
5) Increased Clearance Configurations using (2) 45 deg. Long Sweep
elbows should be considered equivalent to one 90 deg. elbow.
COUPLING
MIN.
12"
FROM
WALL
ELBOW OR
COUPLING
12"
TO GROUND OR
HIGHEST ANTICIPATED
SNOW LEVEL
Horizontal Termination (Single Pipe)
VENT/FLUE PIPE TERMINATIONS
12" MIN.
The vent/flue pipe may terminate vertically, as through a roof, or
horizontally, as through an outside wall.
Vertical vent/flue pipe terminations should be as shown in the
following figure. Refer to Section IX, Vent/Flue Pipe and Combustion Air Pipe - Termination Locations for details concerning
location restrictions. The penetration of the vent through the roof
must be sealed tight with proper flashing such as is used with a
plastic plumbing vent.
Horizontal vent/flue pipe terminations should be as shown in the
following figure. Refer to Section IX, Vent/Flue Pipe and Combustion Air Pipe - Termination Locations for details concerning location restrictions. A 2 3/8” diameter wall penetration is required for
2” diameter pipe while a 3 1/2” diameter hole is required for 3”
diameter pipe. To secure the pipe passing through the wall and
prohibit damage to piping connections, a coupling should be installed on either side of the wall and solvent cemented to a length
of pipe connecting the two couplings. The length of pipe should
be the wall thickness plus the depth of the socket fittings to be
installed on the inside and outside of the wall. The wall penetration should be sealed with silicone caulking material.
In a basement installation, the vent/flue pipe can be run between
joist spaces. If the vent pipe must go below a joist and then up
into the last joist space to penetrate the header, two 45° elbows
should be used to reach the header rather than two 90° elbows.
VENT/FLUE TEE
or
90° ELBOW TURNED
DOWN
Horizontal Termination (Single Pipe)
Above Highest Anticipated Snow Level
DIRECT VENT (DUAL PIPE) PIPING
The inlet air screens provided in the installation instruction packet
are available for the installer to use in the inlet of the combustion
air pipe to prevent animals from building nests in the combustion
air pipe. Installation of screens, while strongly recommended, is
not required and will not affect performance of the unit.
Direct vent installations require both a combustion air intake and
a vent/flue pipe. The pipes may be run horizontally and exit through
the side of the building or run vertically and exit through the roof of
the building. The pipes may be run through an existing unused
chimney; however, they must extend a minimum of 12 inches
above the top of the chimney. The space between the pipes and
the chimney must be closed with a weather tight, corrosion resistant flashing. Both the combustion air intake and a vent/flue pipe
terminations must be in the same atmospheric pressure zone.
For details concerning connection of pipes to the furnace, refer to
the Section IX, Vent/Flue Pipe and Combustion Pipe - Standard
Furnace Connections or Alternate Furnace Connections.
TEE
12 " Min To
Roof Or
Highest Anticipated
Snow Level
VENT/FLUE
AND
COMBUSTION AIR PIPE LENGTHS
AND
DIAMETERS
Refer to the following table for applicable length, elbows, and
pipe diameter for construction of the vent/flue and combustion air
intake pipe systems of a direct vent (dual pipe) installation. The
number of elbows tabulated represents the number of elbows
and/or tees in each (Vent/Flue & Combustion Air Intake) pipe.
Elbows and/or tees used in the terminations must be included
when determining the number of elbows in the piping systems.
Vertical Termination (Single Pipe)
16
If the combustion air intake pipe is to be installed above a finished
ceiling or other area where dripping of condensate will be objectionable, insulation of the combustion air pipe may be required.
Use 1/2” thick closed cell foam insulation such as Armaflex or
Insultube where required.
Dire ct V e nt (Dual Pipe )
Maximum A llow able Length of V ent/Flue & Combustion
A ir Intake Pipe (f t)
Pipe
Number of Elbow s (1)(2)(3)(5)
Unit Input V ent/Flue/A ir Intake
Size (4)
Termination
(Btu)
2
3
4
5
6
7
(in.)
Standard
045_3
A lternate
Standard
070_3
A lternate
Standard
070_4
A lternate
Standard
090_4
A lternate
Standard
090_5
A lternate
Standard
115_5
A lternate
3" MIN
24" MAX
8
2
2
68
55
65
52
62
49
59
46
56
43
53
40
50
37
2
2
68
55
65
52
62
49
59
46
56
43
53
40
50
37
2
2
46
33
43
30
27
3
3
68
55
65
52
62
49
59
46
56
43
53
40
50
37
3
3
68
55
65
52
62
49
59
46
56
43
53
40
50
37
3
3
68
55
65
52
62
49
59
46
56
43
53
40
50
37
40
12" MIN
3" MIN
24" MAX
Standard Horizontal Terminations (Dual Pipe)
Not Recommended
90°
MEDIUM
RADIUS
ELBOW
1) Minimum requirement for each vent pipe is five (5) feet in length and one
elbow/tee.
2) Tees and/or elbows used in the vent/flue termination must be included
when determining the number of elbows in the piping system.
3) 3” diameter pipe can be used in place of 2” diameter pipe.
4) Increased Clearance Configurations using (2) 45 deg. Long Sweep
elbows should be considered equivalent to one 90 deg. elbow.
VENT/FLUE
AND
24" MAX
24" MAX
3" MIN
AIR
INTAKE
COMBUSTION AIR PIPE TERMINATIONS
The vent/flue and combustion air pipes may terminate vertically, as
through a roof, or horizontally, as through an outside wall.
Vertical pipe terminations should be as shown in the following
figure. Refer to Section IX, Vent/Flue Pipe and Combustion Pipe Termination Locations for details concerning location restrictions.
The penetrations through the roof must be sealed tight with proper
flashing such as is used with a plastic plumbing vent.
Alternate Horizontal Vent Termination (Dual Pipe)
12" MIN
12" MIN.
3" MIN.
24" MAX.
VENT/FLUE
TEE
SUPPORT
STRAPS
TEE
COMBUSTION
AIR INTAKE
SCREEN
90°
MEDIUM
RADIUS
ELBOWS
12" MIN.
12" MIN.
TO ROOF OR
HIGHEST
ANTICIPATED
SNOW LEVEL
12" MIN. ABOVE
HIGHEST ANTICIPATED
SNOW LEVEL
COMBUSTION
AIR INTAKE.
VENT/FLUE
90º
MEDIUM RADIUS
ELBOWS
12" MIN. ABOVE
HIGHEST ANTICIPATED
SNOW LEVEL
SCREEN
Standard Horizontal Terminations Above Anticipated Snow
Level (Dual Pipe)
24" MAX.
3" MIN.
90°
Medium Radius
Elbow
Vertical Terminations (Dual Pipe)
Horizontal terminations should be as shown in the following figure. Refer to Section IX, Vent/Flue Pipe and Combustion Pipe Termination Location for location restrictions. A 2 3/8 inch diameter
wall penetration is required for 2” diameter pipe while a 3 1/2 inch
diameter hole is required for 3” diameter pipe. To secure the pipe
passing through the wall and prohibit damage to piping connections, a coupling should be installed on either side of the wall and
solvent cemented to a pipe connecting the two couplings. The
pipe length should be the wall thickness plus the depth of the
socket fittings to be installed on the inside and outside of the wall.
The wall penetration should be sealed with silicone caulking material.
17
Vent
12” Min.
Screen
24” Max.
24” Max.
3” Min.
Air Intake
12” Min. Above
Highest Anticipated
Snow Level
Alternate Vent Termination Above Anticipated Snow Level
(Dual Pipe)
In a basement installation, the pipes may be run between the joist
spaces. If the pipes must go below the joist and then up into the
last joist space to penetrate the header, two 45° elbows should be
used to reach the header rather than two 90° elbows.
•
•
VENT/INTAKE TERMINATIONS FOR INSTALLATION OF MULTIPLE
DIRECT VENT FURNACES
•
•
If more than one direct vent furnace is to be installed vertically
through a common roof top, maintain the same minimum clearances between the exhaust vent and air intake terminations of
adjacent units as with the exhaust vent and air intake terminations
of a single unit.
If more than one direct vent furnace is to be installed horizontally
through a common side wall, maintain the clearances as in the
following figure. Always terminate all exhaust vent outlets at the
same elevation and always terminate all air intakes at the same
elevation.
•
The drain line between furnace and drain location must
maintain a 1/4 inch per foot downward slope toward the
drain.
Do not trap the drain line in any other location than at
the drain trap supplied with the furnace.
Do not route the drain line outside where it may freeze.
If the drain line is routed through an area which may
see temperatures near or below freezing, precautions
must be taken to prevent condensate from freezing
within the drain line.
If an air conditioning coil is installed with the furnace, a
common drain may be used. An open tee must be
installed in the drain line, near the cooling coil, to
relieve positive air pressure from the coil’s plenum.
This is necessary to prohibit any interference with the
function of the furnace’s drain trap.
UPRIGHT INSTALLATIONS
90°
Medium
Radius
Elbows
24" Max.
In an upright installation drain hoses are connected to drain ports
on the rubber elbow and the recuperator coil front cover. The drain
lines are then routed through the right or left side panel and into the
drain trap secured to the outside of the cabinet.
NOTE: Refer to Section X, Condensate Drain Lines and Drain Trap
- Alternate Vent/Flue Hose Connections for upright installations
using an alternate vent/flue outlet.
Vents
STANDARD RIGHT
3" Min. 24" Max.
3" Min.
24" Max.
3" Min.
OR
LEFT SIDE DRAIN HOSE CONNECTIONS
Upright installations using the standard vent/flue outlet require drain
hoses to be connected as follows. The following quantity of hoses,
tubes, and hose clamps are provided with the unit.
Screen
Horizontal Venting Of Multiple Units
CONCENTRIC VENT TERMINATION
Refer to the directions provided with the Concentric Vent Kit (DCVK)
for installation specifications.
X. CONDENSATE DRAIN LINES & DRAIN TRAP
Hose and Tube Identification
1. Remove the rubber plug from the front cover drain port (right
or left side, depending on the intended drain trap mounting).
2. Secure Hose A to front cover drain port with a red hose
clamp. Route hose to rear side panel grommet hole.
GENERAL
A condensing gas furnace achieves its high level of efficiency by
extracting almost all of the heat from the products of combustion
and cooling them to the point where condensation takes place.
The condensate which is generated must be piped to an appropriate drain location.
In upright installations, the furnace’s drain hoses may exit either
the right or left side of the furnace. NOTE: If the alternate vent/flue
outlet is utilized in an upright installation, the drain trap and drain
connections must be located on the same side as the alternate
vent/flue outlet.
In horizontal installations, the drain hoses will exit through the
bottom (down side) of the unit with the drain trap suspended beneath the furnace. The field-supplied drain system must be in
accordance with all local codes and the instructions in the following sections.
NOTE: For left side drainage, grommets will have to be relocated
to left side panel.
Follow the bullets listed below when installing the drain system.
Refer to the following sections for specific details concerning furnace drain trap installation and drain hose hook ups.
•
The drain trap supplied with the furnace must be used.
•
The drain line between furnace and drain location must
be constructed of 3/4” PVC or CPVC.
RIGHT SIDE
PANEL
RUBBER
ELBOW
RUBBER ELBOW
DRAIN PORT
SILVER HOSE CLAMP
TUBE 1
HOSE
B
SIDE PANEL
GROMMET
HOLES
TUBE(S) 2
FRONT COVER
DRAIN PORT
RED HOSE
CLAMP
HOSE
A GREEN
HOSE
CLAMPS
(3 PLACES)
DRAIN
TRAP
Upright “Standard” Connections - Right Side
18
FRONT COVER
DRAIN PORT
RUBBER
ELBOW
RED HOSE
CLAMP
FRONT COVER
DRAIN PORT
RUBBER ELBOW
(EXTERNALLY
MOUNTED)
RUBBER
ELBOW
DRAIN PORT
HOSE A
SILVER HOSE CLAMP
TUBE 1 GREEN HOSE
CLAMPS
(3 PLACES)
HOSE B
SILVER HOSE
CLAMP
SIDE PANEL
DRAIN
HOLES
RUBBER
ELBOW
DRAIN PORT
TUBE 1
TUBE(S) 2
SIDE PANEL
GROMMET
HOLES
GREEN HOSE
CLAMPS
(3 PLACES)
DRAIN
TRAP
RED HOSE
CLAMP
HOSE B
HOSE A
DRAIN TRAP
TUBE(S) 2
Upright “Alternate” Connections - Right Side Only
Upright “Standard” Connections - Left Side
3. Remove grommet from front right-side panel drain hole.
Seal hole in grommet with large end of plug. Reinstall
grommet and plug into side panel drain hole.
4. Cut 1/4 inch from the end of the drain port on the externally
mounted rubber elbow. Discard cut portion.
5. Insert Tube 1 into rubber elbow drain port and secure with
a silver hose clamp. Angle tube outward toward front of
furnace.
6. Cut 17 7/8 inches from the long end of Hose B and discard.
7. Secure remaining end of Hose B to exposed end of Tube 1
with a green hose clamp. Route hose toward right side
panel grommet holes.
8. Insert short end of one Tube 2 through rear right side panel
grommet drain hole. Secure tube to Hose A with a green
hose clamp.
9. Insert short end of remaining Tube 2 into Hose B from
rubber elbow and secure with green hose clamp. Ensure
hoses and tubes maintain a downward slope for proper
drainage and are not kinked or binding.
For details concerning mounting of the drain trap, refer to the following section.
3. Cut and remove 1/4 inch from the end of the drain port on
the rubber elbow.
4. Insert Tube 1 into rubber elbow drain port and secure with
silver hose clamp. Angle tube outward toward front of
furnace.
5. Right side drains
Cut 17 3/4 inches from the long end (end opposite the
bend) of Hose B, discarding the 17 3/4 inch piece and
saving the part with the bend. Secure the remaining hose
to Tube 1 with a green hose clamp. Route the other end of
Hose B to front right side panel grommet hole.
Left side drains
Cut “X” inches from the long end of Hose B and discard.
Refer to table for appropriate length to cut. Secure remaining
hose to Tube 1 with a green hose clamp. Route other end
of Hose B to front left side panel grommet hole.
Cabinet Width
Models
"X" Length to Cut From Long
(inches)
(kBTU_Tons)
End of Hose B
17 1/2
21
24 1/2
045__30
070__30
070__40
090__40
090__50
115__50
7 inches
UPRIGHT DRAIN TRAP MOUNTING (LEFT
3 1/2 inches
OR
RIGHT SIDE PANEL)
1. Insert drain tubes into drain trap and position the drain trap
against the side panel. NOTE: Drain tubes must reach the
bottom of the drain trap.
2. Secure drain trap to side panel at the mounting holes
(dimples or crosshairs) located below the grommet drain
holes.
3. Attach PVC drain line to drain trap outlet with either a 90°
elbow or coupling.
None
6. Insert short end of each Tube 2 through side panel grommet
holes. Secure tubes to Hose A and Hose B with green
hose clamps. Ensure hoses and tubes maintain a
downward slope for proper drainage and that they are not
kinked or binding.
For details concerning mounting of the drain trap, refer to Section
X, Condensate Drain Lines and Drain Trap - Upright Drain Trap
Mounting.
HORIZONTAL INSTALLATIONS
RIGHT SIDE DOWN
Horizontal installations with the right side down require that the
drain hoses be connected to the right side front cover drain port
and the rubber elbow drain port.
ALTERNATE VENT/FLUE DRAIN HOSE CONNECTIONS
Upright installations using the alternate vent/flue outlet will require
“right-side only” drain hoses to be connected as follows. Refer to
Section IX, Vent/Flue Pipe and Combustion Air Pipe for details on
alternate vent/flue pipe connection.
1. Remove the rubber plug from the front cover right-side drain
port. Save for use in step 3.
2. Secure Hose A to front cover drain port with a red hose
clamp. Route hose to rear right side panel grommet hole.
Make connections as follows:
1. Remove the rubber plug from the coil front cover drain port.
2. Secure Hose A to front cover drain tap with a red hose clamp.
Route hose to rear right (down) side panel grommet holes.
19
HOSE A
INDUCED
DRAFT BLOWER
DRAIN PORT
RED HOSE
CLAMP
HOSE B
SIDE PANEL
GROMMET
HOLES
HOSE B
FRONT
COVER
PRESSURE
TAP
FRONT
COVER
PRESSURE
TAP
RIGHT
SIDE
PANEL
TUBES 2
GREEN
HOSE TUBE 1
CLAMP
(3 PLACES)
HOSE A
GREEN HOSE
CLAMPS
(3 PLACES)
RUBBER ELBOW
DRAIN PORT
SILVER HOSE
CLAMP
LEFT SIDE
PANEL
TUBE(S) 2
FRONT COVER
DRAIN PORT
DRAIN TRAP
RED HOSE CLAMP
Horizontal Connections - Right Side Down
SIDE PANEL
GROMMET
HOLES
3. Cut 1/4 inch from the end of the drain port on the rubber
elbow and discard.
4. Insert Tube 1 into rubber elbow drain port and secure with
a silver hose clamp. Angle tube outward toward front of
furnace.
5. Cut 17 3/4 inches from the long end (end opposite the
bend) of Hose B, discarding the 17 3/4 inch piece and
saving the part with the bend.
6. Secure remaining end of Hose B to exposed end of Tube 1
with a green hose clamp. Route hose to front right down
side panel grommet holes.
7. Cut 5 1/2 inches straight length from the long end (end with
the taper) of each Tube 2. Save the 5 1/2 inch long pieces
and discard the pieces with the bend.
8. Insert approximately one inch of each Tube 2 through the
right down side panel grommet holes. Secure tubes to
Hose A and Hose B using green hose clamps. Ensure
hoses and tubes maintain a downward slope for proper
drainage and are not kinked or bound.
For details concerning mounting of the drain trap, refer to Section
X, Condensate Drain Lines and Drain Trap - Horizontal Drain Trap
Mounting (left or right side panel).
Horizontal Connections - Left Side Down
4. Remove the rubber cap from the side drain port on the
rubber elbow.
5. Secure the short end of Hose B to rubber elbow side drain
port using a green hose clamp. NOTE: For left side drainage,
route hose to far left (down) side panel grommet holes.
NOTE: Horizontal left side connections (when using new
side port drain elbow) does not require connecting a hose
to the induced draft blower housing.
6. Cut 5 1/2 inches straight length from the long end (end with
a taper) of each Tube 2. Save the 5 1/2 inch long pieces and
discard the pieces with the bends.
7. Insert approximately one inch of each Tube 2 through left
side panel grommet hole. Secure tubes to Hose A and
Hose B with a green hose clamps. NOTE: Tube must
reach bottom of trap. Ensure hoses and tubes maintain a
downward slope for proper drainage and that they are not
kinked or binding.
For details concerning mounting of the drain trap, refer to Section
X, Condensate Drain Lines and Drain Trap - Horizontal Drain Trap
Mounting (left or right side panel).
LEFT SIDE DOWN
HORIZONTAL DRAIN TRAP MOUNTING (LEFT
PANEL)
Horizontal installations with the left side panel down will require
drain hoses to be connected to the left side front cover drain port
and the side drain port on the rubber elbow.
OR
RIGHT SIDE
1. Position the drain trap against side panel with drain tubes
inserted into trap. Note that the trap may be orientated with
the outlet facing either the furnace’s top cover or base pan.
2. Secure drain trap to side panel at the dimples or crosshairs
located on either side of the grommet drain holes.
3. Confirm that tubes reach bottom of drain trap and that all
hoses maintain a downward slope and are not kinked or
binding.
4. Attach PVC drain line to drain trap outlet with either a 90°
elbow or coupling.
1. Remove the rubber plug from the coil front cover left (down)
side drain port.
2. Relocate the front cover pressure switch hose connection
from the right side (as shipped) pressure tap to the left
(down) side tap. The pressure switch hose must be
connected to the down side to guard against blocked drain
conditions. Cut hose to appropriate length to minimize
sagging. Plug right (unused) pressure tap with plug
removed from left side.
3. Secure Hose A to front cover drain port with a red hose
clamp. Route hose to rear left (down) side panel grommet
holes. NOTE: For left side drainage, grommets must be
relocated to left side panel.
20
XI. ELECTRICAL CONNECTIONS
NOTE: Wire routing must not to interfere with circulator blower
operation, filter removal, or routine maintenance.
WARNING
CAUTION
TO AVOID THE RISK OF ELECTRICAL SHOCK, WIRING TO THE UNIT MUST BE
POLARIZED AND GROUNDED.
EDGES OF SHEET METAL HOLES MAY BE SHARP. USE GLOVES AS A
PRECAUTION WHEN REMOVING HOLE PLUGS.
1. Remove the burner compartment door.
2. Remove and save the two screws securing the junction box
to the side panel.
3. Relocate junction box and associated plugs and grommets
to opposite side panel. Secure with screws removed in
step 2.
WARNING
TO AVOID INJURY, ELECTRICAL SHOCK OR DEATH, DISCONNECT ELECTRICAL
POWER BEFORE SERVICING OR CHANGING ANY ELECTRICAL WIRING.
CAUTION
*
*
LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS.
WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION.
VERIFY PROPER OPERATION AFTER SERVICING.
*
*
ALTERNATE
JUNCTION BOX
LOCATION
*
*
*
*
*
STANDARD
JUNCTION BOX
LOCATION
WIRING HARNESS
The wiring harness is an integral part of this furnace. Field alteration to comply with electrical codes should not be required. Wires
are color coded for identification purposes. Refer to the wiring
diagram for wire routings. If any of the original wire as supplied
with the furnace must be replaced, it must be replaced with wiring
material having a temperature rating of at least 105°C. Any replacement wiring must be copper conductor.
Junction Box Relocation
WARNING
115 VOLT LINE CONNECTIONS
TO AVOID THE RISK OF INJURY, ELECTRICAL SHOCK OR DEATH, THE FURNACE
Before proceeding with electrical connections, ensure that the supply voltage, frequency, and phase correspond to that specified on
the unit rating plate. Power supply to the furnace must be N.E.C.
Class 1, and must comply with all applicable codes. The furnace
must be electrically grounded in accordance with local codes or, in
their absence, with the latest edition of The National Electric Code,
ANSI NFPA 70 and/or The Canadian Electric Code CSA C22.1.
Use a separate fused branch electrical circuit containing properly
sized wire, and fuse or circuit breaker. The fuse or circuit breaker
must be sized in accordance with the maximum overcurrent protection specified on the unit rating plate. An electrical disconnect
must be provided at the furnace location.
MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES OR,
NOTE: Line polarity must be observed when making field
connections.
IN THEIR ABSENCE, WITH THE LATEST EDITION OF THE
NATIONAL ELECTRIC
CODE.
To ensure proper unit grounding, the ground wire should run from
the furnace ground screw located inside the furnace junction box
all the way back to the electrical panel. NOTE: Do not use gas
piping as an electrical ground. To confirm proper unit grounding,
turn off the electrical power and perform the following check.
1. Measure resistance between the neutral (white) connection
and one of the burners.
2. Resistance should measure 10 ohms or less.
This furnace is equipped with a blower door interlock switch which
interrupts unit voltage when the blower door is opened for servicing. Do not defeat this switch.
Connect hot, neutral, and ground wires as shown in the wiring
diagram located on the unit’s blower door. For direct vent applications, the cabinet opening to the junction box must be sealed air
tight using either a UL approved bushing such as Heyco Liquid
Tight or by applying a UL approved non-reactive sealant to bushing.
Line polarity must be observed when making field connections.
Line voltage connections can be made through either the right or
left side panel. The furnace is shipped configured for a left side
electrical connection with the junction box located inside the burner
compartment. To make electrical connections through the opposite side of the furnace, the junction box must be relocated to the
other side of the burner compartment prior to making electrical
connections. To relocate the junction box, follow the steps shown
below.
21
24 VOLT THERMOSTAT WIRING
NOTE: Wire routing must not interfere with circulator blower
operation, filter removal, or routine maintenance.
Low voltage connections can be made through either the right or
left side panel. Thermostat wiring entrance holes are located in the
blower compartment. Wire routing must not to interfere with circulator blower operation, filter removal, or routine maintenance. Refer to the following figure for thermostat connections to the integrated control module terminal strip.
Y
W
Y
W
Y
W
R
R
R
G
G
R
Y
C
G
C
HEATING
ROOM
THERMOSTAT
W
C
HEATING AND
COOLING ROOM
THERMOSTAT
FURNACE
FURNACE
REMOTE
CONDENSING
UNIT
Thermostat Diagram
This furnace is equipped with a 40 VA transformer to facilitate use
with most cooling equipment. Consult the wiring diagram, located
on the blower compartment door, for further details of 115 Volt and
24 Volt wiring.
115 VOLT LINE CONNECTION OF ACCESSORIES (ELECTRONIC
AIR CLEANER)
If it is necessary for the installer to supply additional line voltage
wiring to the inside of the furnace, the wiring must conform to all
local codes, and have a minimum temperature rating of 105°C. All
line voltage wire splices must be made inside the furnace junction
box.
The integrated control module electronic air cleaner terminals (EAC)
are energized with 115 volts whenever the circulator blower is energized.
24 VOLT HUMIDIFIER
The yellow wire connected to the I.D. Blower pressure switch is
powered anytime the pressure switch is closed and provides 24
VAC humidifier control. Remove the yellow wire and connect the
supplied brown jumper wire to the pressure switch terminal. Reconnect the yellow wire to the “piggyback” terminal on the brown
jumper and then connect the 24 VAC line of the humidifier to the
stripped end of the brown wire. Using a wire nut or a field-supplied
quick connect terminal can make this connection. The wiring must
conform to all local and national codes. Connect the COM side of
the humidifier to the B/C terminal on the furnace control board (or to
the COM side of the 24 VAC transformer). DO NOT CONNECT 115V
HUMIDIFIER TO THESE TERMINALS.
XII. GAS SUPPLY AND PIPING
GENERAL
The furnace rating plate includes the approved furnace gas input
rating and gas types. The furnace must be equipped to operate on
the type of gas applied. This includes any conversion kits required
for alternate fuels and/or high altitude.
WARNING
TO AVOID INJURY, ELECTRICAL SHOCK OR DEATH, DISCONNECT ELECTRICAL
CAUTION
POWER BEFORE SERVICING OR CHANGING ANY ELECTRICAL WIRING.
The furnace’s integrated control module is equipped with line voltage accessory terminals for controlling power to an optional fieldsupplied electronic air cleaner.
The accessory load specifications are as follows:
Electronic Air Cleaner
1.0 Amp maximum at 120 VAC
Turn OFF power to the furnace before installing any accessories.
Follow the air cleaner manufacturers’ instructions for locating,
mounting, grounding, and controlling these accessories. Accessory wiring connections are to be made through the 1/4" quick
connect terminals provided on the furnace integrated control module. The electronic air cleaner hot terminal is identified as EAC-H.
The electronic air cleaner neutral terminal is identified as LINE
NEUTRAL. All field wiring must conform to applicable codes. Connections should be made as shown below.
OPTIONAL
ACCESSORIES
ELECTRONIC
AIR CLEANER
120 VAC
HOT AND
PARK
TERMINALS
120 VAC
NEUTRAL
TERMINALS
INTEGRATED
CONTROL
MODULE
12 PIN
CONNECTOR
Accessories Wiring
TO PREVENT UNRELIABLE OPERATION OR EQUIPMENT DAMAGE, THE INLET
GAS SUPPLY PRESSURE MUST BE AS SPECIFIED ON THE UNIT RATING PLATE
WITH ALL OTHER HOUSEHOLD GAS FIRED APPLIANCES OPERATING.
Inlet gas supply pressures must be maintained within the ranges
specified below. The supply pressure must be constant and available with all other household gas fired appliances operating. The
minimum gas supply pressure must be maintained to prevent
unreliable ignition. The maximum must not be exceeded to prevent unit overfiring.
Natural Gas
Propane Gas
Inlet Gas Supply Pressure
Minimum:5.0" W.C. Maximum :10.0" W.C.
Minimum:11.0" W.C. Maximum :13.0" W.C.
HIGH ALTITUDE DERATE
When this furnace is installed at high altitude, the appropriate High
Altitude orifice kit must be applied. This is required due to the
natural reduction in the density of both the gas fuel and combustion air as altitude increases. The kit will provide the proper design
certified input rate within the specified altitude range.
High altitude kits are purchased according to the installation altitude and usage of either natural or propane gas. Contact your
distributor for a tabular listing of appropriate altitude ranges and
corresponding manufacturer’s high altitude (Natural, Propane Gas,
and/or Pressure Switch) kits.
Do not derate the furnace by adjusting the manifold pressure to a
lower pressure than specified on the furnace rating plate. The
combination of the lower air density and a lower manifold pressure
will prohibit the burner orifice from drawing the proper amount of
air into the burner. This may cause incomplete combustion, flashback, and possible yellow tipping.
22
In some areas the gas supplier may artificially derate the gas in an
effort to compensate for the effects of altitude. If the gas is artificially derated, the appropriate orifice size must be determined
based upon the BTU/ft3 content of the derated gas and the altitude.
Refer to the National Fuel Gas Code, NFPA 54/ANSI Z223.1, and
information provided by the gas supplier to determine the proper
orifice size.
A different pressure switch may be required at high altitude regardless of the BTU/ft3 content of the fuel used. Contact your distributor
for a tabular listing of appropriate altitude ranges and corresponding manufacturer’s pressure switch kits.
Natural Gas Capacity of Pipe
In Cubic Fe e t of Gas Pe r Hour (CFH)
Length of
Nominal Black Pipe Size
Pipe in Feet
1/2"
3/4"
1"
1 1/4"
10
132
278
520
1050
20
92
190
350
730
30
73
152
285
590
40
63
130
245
500
50
56
115
215
440
60
50
105
195
400
70
46
96
180
370
80
43
90
170
350
90
40
84
160
320
100
38
79
150
305
(Pressure 0.5 psig or less and pressure drop of 0.3" W.C.; Based on
0.60 Specif ic Gravity Gas)
PROPANE GAS CONVERSION
WARNING
CFH =
1 1/2"
1600
1100
980
760
670
610
560
530
490
460
BTUH Furnace Input
Heating Value of Gas (BTU/Cubic Foot)
POSSIBLE PROPERTY DAMAGE, PERSONAL INJURY OR DEATH MAY OCCUR IF
THE CORRECT CONVERSION KITS ARE NOT INSTALLED. THE APPROPRIATE KITS
MUST BE APPLIED TO INSURE SAFE AND PROPER FURNACE OPERATION. ALL
To connect the furnace to the building’s gas piping, the installer
must supply a ground joint union, drip leg, manual shutoff valve,
and line and fittings to connect to gas valve. In some cases, the
CONVERSIONS MUST BE PERFORMED BY A QUALIFIED INSTALLER OR SERVICE
installer may also need to supply a transition piece from 1/2" pipe
AGENCY.
to a larger pipe size.
This unit is configured for natural gas. The appropriate The following stipulations apply when connecting gas piping. Remanufacturer’s propane gas conversion kit, must be applied for fer to Gas Piping Connections figure for typical gas line connecpropane gas installations. Refer to the Section VIII, Propane Gas tions to the furnace.
/ High Altitude Installations section for details.
• Use black iron or steel pipe and fittings for building piping.
GAS VALVE
Where possible, use new pipe that is properly chamfered,
This unit is equipped with a 24 volt gas valve controlled during
reamed, and free of burrs and chips. If old pipe is used, be
furnace operation by the integrated control module. As shipped,
sure it is clean and free of rust, scale, burrs, chips, and old
the valve is configured for natural gas. The valve is field convertible
pipe joint compound.
for use with propane gas by replacing the regulator spring with a
•
Use pipe joint compound on male threads ONLY. Always
propane gas spring from an appropriate manufacturer’s propane
use pipe joint compound (pipe dope) that is APPROVED
gas conversion kit. Taps for measuring the gas supply pressure
FOR ALL GASES. DO NOT apply compound to the first two
and manifold pressure are provided on the valve.
threads.
The gas valve has a manual ON/OFF control located on the valve
itself. This control may be set only to the “ON” or “OFF” position. • Use ground joint unions.
Refer to the lighting instructions label or Section XIV, Startup Procedure & Adjustment for use of this control during start up and shut • Install a drip leg to trap dirt and moisture before it can enter
the gas valve. The drip leg must be a minimum of three
down periods.
inches long.
GAS PIPING CONNECTIONS
•
Install a 1/8" NPT pipe plug fitting, accessible for test gage
connection, immediately upstream of the gas supply
connection to the furnace.
•
Always use a back-up wrench when making the connection
to the gas valve to keep it from turning. The orientation of
the gas valve on the manifold must be maintained as
shipped from the factory. Maximum torque for the gas valve
connection is 375 in-lbs; excessive over-tightening may
damage the gas valve.
•
Install a manual shutoff valve between the gas meter and
unit within six feet of the unit. If a union is installed, the
union must be downstream of the manual shutoff valve,
between the shutoff valve and the furnace.
•
•
Tighten all joints securely.
GENERAL
CAUTION
TO AVOID POSSIBLE UNSATISFACTORY OPERATION OR EQUIPMENT DAMAGE
DUE TO UNDERFIRING OF EQUIPMENT, USE THE PROPER SIZE OF
NATURAL/PROPANE GAS PIPING NEEDED WHEN RUNNING PIPE FROM THE
METER/TANK TO THE FURNACE.
When sizing a trunk line, be sure to include all appliances which
will operate simultaneously when sizing a trunk line.
The gas piping supplying the furnace must be properly sized based
on the gas flow required, specific gravity of the gas, and length of
the run. The gas line installation must comply with local codes, or
in their absence, with the latest edition of the National Fuel Gas
Code, NFPA 54/ANSI Z223.1.
Connect the furnace to the building piping by one of the
following methods:
–
–
23
Rigid metallic pipe and fittings.
Semi-rigid metallic tubing and metallic fittings.
Aluminum alloy tubing must not be used in exterior
locations. In order to seal the grommet cabinet
penetration, rigid pipe must be used to reach the
outside of the cabinet. A semi-rigid connector to the
gas piping may be used from there.
•
•
DIRECT/STANDARD INLET PIPING
Use listed gas appliance connectors in accordance with
their instructions. Connectors must be fully in the same
room as the furnace.
When gas piping enters directly to the gas valve through the standard inlet hole, the installer must supply straight pipe with a ground
joint union to reach the exterior of the furnace. The rigid pipe must
be long enough to reach the outside of the cabinet to seal the
grommet cabinet penetration. A semi-rigid connector to the gas
piping can be used outside the cabinet per local codes.
Protect connectors and semi-rigid tubing against physical
and thermal damage when installed. Ensure aluminumalloy tubing and connectors are coated to protect against
external corrosion when in contact with masonry, plaster, or
insulation, or subjected to repeated wetting by liquids such
as water (except rain water), detergents, or sewage.
When gas piping enters indirectly to the gas valve through the
alternate gas inlet hole, the following 1/2 inch pipe fittings (starting from the gas valve) to reach the outside of the cabinet must be
supplied:
• (1) 90 degree street elbow
MANUAL
SHUT OFF VALVE
(UPSTREAM FROM
GROUND JOINT
PIPE UNION)
GAS VALVE
MANIFOLD
INDIRECT/ALTERNATE INLET PIPING
BURNERS
ALTERNATE
GAS LINE
LOCATION
PLUG IN
ALTERNATE
GAS LINE
HOLE
•
•
•
•
HEIGHT REQUIRED
BY LOCAL CODE
GROMMET
IN STANDARD
GAS LINE HOLE
DRIP LEG
GROUND JOINT
PIPE UNION
(1) 2 1/2” pipe nipple
(1) 90 degree elbow
Straight Pipe
The straight pipe must be long enough to reach the outside
of the cabinet so as to seal the grommet cabinet penetration
and to install the ground joint union outside the cabinet. A
semi-rigid connector to the gas piping can be used outside
the cabinet per local codes.
GAS PIPING CHECKS
Before placing unit in operation, leak test the unit and gas connections.
MANUAL SHUT OFF VALVE
(UPSTREAM FROM
GROUND JOINT PIPE UNION)
GROUND JOINT
PIPE UNION
WARNING
TO AVOID THE POSSIBILITY OF EXPLOSION OR FIRE, NEVER USE A MATCH OR
OPEN FLAME TO TEST FOR LEAKS.
DRIP LEG
Check for leaks using an approved chloride-free soap and water
solution, an electronic combustible gas detector, or other approved
testing methods.
GROMMET
IN STANDARD
GAS LINE HOLE
GAS VALVE
BURNERS
NOTE: Never exceed specified pressures for testing. Higher
pressure may damage the gas valve and cause subsequent
overfiring, resulting in heat exchanger failure.
Disconnect this unit and shutoff valve from the gas supply piping
system before pressure testing the supply piping system with
pressures in excess of 1/2 psig (3.48 kPa).
Isolate this unit from the gas supply piping system by closing its
external manual gas shutoff valve before pressure testing supply
piping system with test pressures equal to or less than 1/2 psig
(3.48 kPa).
DRAIN TRAP
MANIFOLD
ALTERNATE
GAS LINE LOCATION
PLUG-IN ALTERNATE
GAS LINE HOLE
PROPANE GAS TANKS AND PIPING
HORIZONTAL [UPFLOW MODEL]
WARNING
NOTES: 1. WHEN GAS LINE IS IN THE ALTERNATE LOCATION,
SWAP THE POSITION OF THE PLUG AND GROMMET.
2. DRIP LEG MAY TERMINATE WITH A 1/2" X 1/8" PIPE PLUG
TO ACCOMMODATE LINE GAS PRESSURE MEASUREMENT.
PROPANE GAS IS HEAVIER THAN AIR AND ANY LEAKING GAS CAN SETTLE IN
TO PREVENT PROPERTY DAMAGE,
ANY LOW AREAS OR CONFINED SPACES.
PERSONAL INJURY, OR DEATH DUE TO FIRE OR EXPLOSION CAUSED BY A
PROPANE GAS LEAK, INSTALL A GAS DETECTION WARNING DEVICE.
A gas detecting warning system is the only reliable way to detect a
propane gas leak. Rust can reduce the level of odorant in propane gas. Do not rely on your sense of smell. Contact a local
propane gas supplier about installing a gas detecting warning
system. If the presence of gas is suspected, follow the instructions on Page 4 of this manual.
Gas Piping Connections
CAUTION
EDGES OF SHEET METAL HOLES MAY BE SHARP. USE GLOVES AS A
PRECAUTION WHEN REMOVING HOLE PLUGS.
24
All propane gas equipment must conform to the safety standards
of the National Board of Fire Underwriters, NBFU Manual 58.
For satisfactory operation, propane gas pressure must be 11 inch
w.c. at the furnace manifold with all gas appliances in operation.
Maintaining proper gas pressure depends on three main factors:
1. Vaporization rate, depending on temperature of the liquid,
and “wetted surface” area of the container or containers.
2. Proper pressure regulation. (Two-stage regulation is
recommended for both cost and efficiency).
3. Pressure drop in lines between regulators, and between
second stage regulator and the appliance. Pipe size will
depend on length of pipe run and total load of all appliances.
Complete information regarding tank sizing for vaporization, recommended regulator settings, and pipe sizing is available from
most regulator manufacturers and propane gas suppliers.
Since propane gas will quickly dissolve white lead and most standard commercial compounds, special pipe dope must be used.
Shellac-based compounds resistant to the actions of liquefied
petroleum gases such as Gasolac®, Stalactic®, Clyde’s® or John
Crane® are satisfactory.
Refer to the following illustration for typical propane gas installations.
5 to 15 PSIG
(20 PSIG Max.)
First Stage
Regulator
200 PSIG
Maximum
Continuous
11" W.C.
Second Stage
Regulator
Propane Gas Installation (Typ.)
Sizing Between First and Second Stage Regulator*
Maximum Propane Capacities listed are based on 2 psig pressure drop at 10 psig setting.
Capacities in 1,000 BTU/hour.
Pipe or
Nominal Pipe Size
Tubing
Tubing Size, O.D. Type L
Schedule 40
Length,
3/8"
1/2"
5/8"
3/4"
7/8"
1/2"
3/4"
Feet
10
730
1,700
3,200
5,300
8,300
3,200
7,500
20
500
1,100
2,200
3,700
5,800
2,200
4,200
30
400
920
2,000
2,900
4,700
1,800
4,000
40
370
850
1,700
2,700
4,100
1,600
3,700
50
330
770
1,500
2,400
3,700
1,500
3,400
60
300
700
1,300
2,200
3,300
1,300
3,100
80
260
610
1,200
1,900
2,900
1,200
2,600
100
220
540
1,000
1,700
2,600
1,000
2,300
125
200
490
900
1,400
2,300
900
2,100
150
190
430
830
1,300
2,100
830
1,900
175
170
400
780
1,200
1,900
770
1,700
200
160
380
730
1,100
1,800
720
1,500
To convert to capacities at 15 psig settings - multiply by 1.130
To convert to capacities at 5 psig settings - multiply by 0.879
Propane Gas Piping Chart I
Sizing Between Single or Second Stage Regulator and Appliance*
XIII. CIRCULATING AIR & FILTERS
DUCTWORK - AIR FLOW
Duct systems and register sizes must be properly designed for the
CFM and external static pressure rating of the furnace. Design the
ductwork in accordance with the recommended methods of “Air
Conditioning Contractors of America” Manual D.
Install the duct system in accordance with Standards of the National Board of Fire Underwriters for the Installation of Air Conditioning, Warm Air Heating and Ventilating Systems. Pamphlets No.
90A and 90B.
A closed return duct system must be used, with the return duct
connected to the furnace. NOTE: Ductwork must never be attached
to the back of the furnace. Flexible joints may be used for supply
and return connections to reduce noise transmission. To prevent
the blower from interfering with combustion air or draft when a
central return is used, a connecting duct must be installed between the unit and the utility room wall. Never us a room, closet, or
alcove as a return air chamber.
When the furnace is used in connection with a cooling unit, the
furnace should be installed in parallel with or on the upstream side
of the cooling unit to avoid condensation in the heating element.
With a parallel flow arrangement, the dampers or other means
used to control the flow of air must be adequate to prevent chilled
air from entering the furnace and, if manually operated, must be
equipped with means to prevent operation of either unit unless the
damper is in the full heat or cool position.
When the furnace is installed without a cooling coil, it is recommended that a removable access panel be provided in the outlet
air duct. This opening shall be accessible when the furnace is
installed and shall be of such a size that the heat exchanger can be
viewed for visual light inspection or such that a sampling probe
can be inserted into the airstream. The access panel must be
made to prevent air leaks when the furnace is in operation.
When the furnace is heating, the temperature of the return air entering the furnace must be between 55°F and 100°F.
BOTTOM RETURN AIR OPENING [UPFLOW MODELS]
The bottom return air opening on upflow models utilizes a “lance
and cut” method to remove sheet metal from the duct opening in
the base pan. To remove, simply press out the lanced sections by
hand to expose the metal strips retaining the sheet metal over the
duct opening. Using tin snips, cut the metal strips and remove the
sheet metal to free the duct flanges. Using the scribe line along
the duct flange as a guide, unfold the duct flanges around the
perimeter of the opening using a pair of seamer pliers or seamer
tongs. NOTE: Airflow area will be reduced by approximately 18% if
duct flanges are not unfolded. This could cause performance issues and noise issues.
Maximum Propane Capacities Listed are Based on 1/2" W.C. pressure drop at 11" W.C. setting.
Capacities in 1,000 BTU/hour.
Pipe or
Nominal Pipe Size
Tubing
Tubing Size, O.D. Type L
Schedule 40
Length,
3/8"
1/2"
5/8"
3/4"
7/8" 1-1/8" 1/2"
3/4"
1"
1-1/4" 1-1/2"
Feet
10
39
92
199
329
501
935
275
567
1,071 2,205 3,307
20
26
62
131
216
346
630
189
393
732
1,496 2,299
30
21
50
107
181
277
500
152
315
590
1,212 1,858
40
19
41
90
145
233
427
129
267
504
1,039 1,559
50
18
37
79
131
198
376
114
237
448
913
1,417
60
16
35
72
121
187
340
103
217
409
834
1,275
80
13
29
62
104
155
289
89
185
346
724
1,066
100
11
26
55
90
138
255
78
162
307
630
976
125
10
24
48
81
122
224
69
146
275
567
866
150
9
21
43
72
109
202
63
132
252
511
787
200
8
19
39
66
100
187
54
112
209
439
665
250
8
17
36
60
93
172
48
100
185
390
590
CAUTION
EDGES OF SHEET METAL HOLES MAY BE SHARP. USE GLOVES AS A
PRECAUTION WHEN REMOVING HOLE PLUGS.
*Data in accordance with NFPA pamphlet NO. 54
Propane Gas Piping Chart II
25
CUT USING TIN SNIPS
COOLING AIRFLOW REQUIREMENT (CFM)
Input__Airflow
PRESS OUT BY HAND
CUT FOUR CORNERS
AFTER REMOVING SHEET
METAL
SCRIBE LINES OUTLINING
DUCT FLANGES
Duct Flange Cut Outs
800
1000
1200
1400
1600
2000
0453BXA
388*
388*
480
576
---
---
---
0703BXA
---
647*
647*
647*
672
---
---
0704CXA
---
---
583*
583*
672
768
---
0904CXA
---
---
863*
863*
863*
863*
---
0905DXA
---
---
---
777*
777*
777*
960
1155DXA
---
---
---
971*
971*
971*
971*
*Minimum filter area dictated by heating airflow requirement.
Disposable Minimum Filter area (sq. in)
[Based on 300 ft/min filter face velocity]
FILTERS - READ THIS SECTION BEFORE INSTALLING THE
RETURN AIR DUCTWORK
UPRIGHT INSTALLATIONS
Filters must be used with this furnace. Discuss filter maintenance
with the building owner. Filters do not ship with this furnace, but
must be provided by the installer. Filters must comply with UL900
or CAN/ULCS111 standards. If the furnace is installed without filters, the warranty will be voided.
On upflow units, guide dimples locate the side return cutout
locations. Use a straight edge to scribe lines connecting the
dimples. Cut out the opening on these lines.
NOTE: An undersized opening will cause reduced airflow.
Depending on the installation and/or customer preference, differing filter arrangements can be applied. Filters can be installed in
the central return register or a side panel external filter rack kit. As
an alternative a media air filter or electronic air cleaner can be used
as the requested filter.
The following figure shows possible filter locations.
AIR FLOW
CENTRAL
RETURN
GRILLE
FILTER
Refer to Minimum Filter Area tables to determine filter area requirements.
600
800
1000
1200
1400
1600
2000
0453BXA
194*
194*
240
288
---
---
---
0703BXA
---
324*
324*
324*
336
---
---
0704CXA
---
---
291*
291*
336
384
---
0904CXA
---
---
432*
432*
432*
432*
---
0905DXA
---
---
---
388*
388*
388*
480
1155DXA
---
---
---
486*
486*
486*
486*
SIDE RETURN
EXTERNAL FILTER
RACK KIT
(EITHER SIDE)
FILTER
COOLING AIRFLOW REQUIREMENT (CFM)
Input__Airflow
600
*Minimum filter area dictated by heating airflow requirement.
Permanent Minimum Filter Area (sq. in)
[Based on a 600 ft/min filter face velocity]
Possible Upright Upflow
Filter Locations
NOTE: Internal filter retention is not provided on this furnace. If an
internal installation is desired, an internal filter retention kit is available as an accessory. Please see your distributor for details.
HORIZONTAL INSTALLATIONS
Filters must be installed in either the central return register or in the
return air duct work.
26
XIV. STARTUP PROCEDURE & ADJUSTMENT
GAS SUPPLY PRESSURE MEASUREMENT
Furnace must have a 115 VAC power supply properly connected
and grounded. Proper polarity must be maintained for correct operation. In addition to the following start-up and adjustment items,
refer to further information in Section XVI, Operational Checks.
CAUTION
TO PREVENT UNRELIABLE OPERATION OR EQUIPMENT DAMAGE, THE INLET
HEAT ANTICIPATOR SETTING
GAS SUPPLY PRESSURE MUST BE AS SPECIFIED ON THE UNIT RATING PLATE
WITH ALL OTHER HOUSEHOLD GAS FIRED APPLIANCES OPERATING.
The heat anticipator in the room thermostat must be correctly adjusted to obtain the proper number of cycles per hour and to pre- WHITE-RODGERS 36G54 GAS VALVE
vent “overshooting” of the setting. Set the heat anticipator setting to
0.7 amps. Follow the thermostat manufacturer’s instructions on The line pressure supplied to the gas valve must be within the
range specified below. The supply pressure can be measured at
how to adjust the heat anticipator setting.
the gas valve inlet pressure boss or at a hose fitting installed in the
DRAIN TRAP PRIMING
gas piping drip leg. The supply pressure must be measured with
The drain trap must be primed prior to furnace startup. To prime, fill the burners operating. To measure the gas supply pressure, use
the drain trap with water. This ensures proper furnace drainage the following procedure.
upon startup and prohibits the possibility of flue gases escaping
through the drain system.
Open to
Atmosphere
FURNACE OPERATION
Manometer
Hose
Purge gas lines of air prior to startup. Be sure not to purge lines
into an enclosed burner compartment.
Check for leaks using an approved chloride-free soap and water
solution, an electronic combustible gas detector, or other approved
method. Verify that all required kits (propane gas, high altitude,
etc.) have been appropriately installed.
High Fire Regulator
Adjust
Regulator
Vent
Outlet
Pressure Boss
A
FURNACE STARTUP
1.
2.
3.
4.
Close the manual gas shutoff valve external to the furnace.
Turn off the electrical power to the furnace.
Set the room thermostat to the lowest possible setting.
Remove the burner compartment door.
Low Fire
Regulator Adjust
Inlet
Pressure Boss
NOTE: This furnace is equipped with an ignition device which
automatically lights the burner. Do not try to light the burner by
hand.
5. Move the furnace gas valve manual control to the OFF
position.
6. Wait five minutes then smell for gas. Be sure to check near
the floor as some types of gas are heavier than air.
7. If you smell gas after five minutes, immediately follow the
instructions on page 4 of this manual. If you do not smell
gas after five minutes, move the furnace gas valve manual
control to the ON position.
8. Replace the burner compartment door.
9. Open the manual gas shutoff valve external to the furnace.
10. Turn on the electrical power to the furnace.
11. Adjust the thermostat to a setting above room temperature.
12. After the burners are lit, set the thermostat to desired
temperature.
High Fire
Coil Terminal (HI)
Manometer
Coaxial Coil
Terminal (M)
Common
Terminal (C)
On/Off Switch
White-Rodgers Model 36G54 Connected to Manometer
1. Turn OFF gas to furnace at the manual gas shutoff valve
external to the furnace.
2. Connect a calibrated water manometer (or appropriate gas
pressure gauge) at either the gas valve inlet pressure boss
or the gas piping drip leg.
Gas Line
Gas
Shutoff
Valve
FURNACE SHUTDOWN
Gas Line
To Furnace
1. Set the thermostat to the lowest setting. The integrated
control will close the gas valve and extinguish flame.
Following a 15 second delay, the induced draft blower will
be de-energized. After a 100 or 150 second delay period
(field selectable), the circulator blower will be de-energized.
2. Remove the burner compartment door and move the furnace
gas valve manual control to the OFF position.
3. Close the manual gas shutoff valve external to the furnace.
4. Replace the burner compartment door.
Open To
Atmosphere
Drip Leg Cap
With Fitting
Manometer Hose
Manometer
Measuring Inlet Gas Pressure (Alt. Method)
27
NOTE: If measuring gas pressure at the drip leg, a field supplied
hose barb fitting must be installed prior to making the hose
connection. If using the inlet pressure boss on the gas valve,
then use the 36G Valve Pressure Check Kit, Goodman Part No.
0151K00000S.
13. Turn outlet pressure test screw in to seal pressure port
(clockwise, 7 in-lb minimum).
14. Turn on electrical power and gas supply to the system.
15. Turn on system power and energize valve.
16. Using a leak detection solution or soap suds, check for
leaks at pressure boss screw. Bubbles forming indicate a
leak. SHUT OFF GAS AND FIX ALL LEAKS IMMEDIATELY.
NOTE: For gas to gas conversion, consult your dealer for
appropriate conversion.
3. Turn ON the gas supply and operate the furnace and all
other gas consuming appliances on the same gas supply
line.
4. Measure furnace gas supply pressure with burners firing.
Supply pressure must be within the range specified in the
Inlet Gas Supply Pressure table.
Natural Gas
Propane Gas
Manifold Gas Pressure
Gas
Rate
Low Stage
Natural
High Stage
Low Stage
Propane
High Stage
Inlet Gas Supply Pressure
Minimum: 5.0" w.c. Maximum:10.0" w.c.
Minimum: 11.0" w.c. Maximum:13.0" w.c.
If supply pressure differs from table, make the necessary adjustments to pressure regulator, gas piping size, etc., and/or consult
with local gas utility.
5. Turn OFF gas to furnace at the manual shutoff valve and
disconnect manometer. Reinstall plug before turning on
gas to furnace.
6. Turn OFF any unnecessary gas appliances started in step
3.
Range
Nominal
1.7 to 2.3" w.c. 2.0" w.c.
3.2 to 3.8" w.c. 3.5" w.c.
5.7 to 6.3" w.c. 6.0" w.c.
9.7 to 10.3" w.c. 10.0" w.c.
GAS INPUT RATE MEASUREMENT (NATURAL GAS ONLY)
The gas input rate to the furnace must never be greater than that
specified on the unit rating plate. To measure natural gas input
using the gas meter, use the following procedure.
1. Turn OFF the gas supply to all other gas-burning appliances
except the furnace.
GAS MANIFOLD PRESSURE MEASUREMENT AND ADJUSTMENT
2. While the furnace is operating, time and record one
complete revolution of the smallest gas meter dial.
CAUTION
3. Calculate the number of seconds per cubic foot (sec/ ft3) of
gas being delivered to the furnace. If the dial is a one cubic
foot dial, divide the number of seconds recorded in step 2
by one. If the dial is a two cubic foot dial, divide the number
of seconds recorded in step 2 by two.
TO PREVENT UNRELIABLE OPERATION OR EQUIPMENT DAMAGE, THE GAS
MANIFOLD PRESSURE MUST BE AS SPECIFIED ON THE UNIT RATING PLATE.
ONLY MINOR ADJUSTMENTS SHOULD BE MADE BY ADJUSTING THE GAS VALVE
PRESSURE REGULATOR.
Only small variations in gas pressure should be made by adjusting the gas valve pressure regulator. The manifold pressure must
be measured with the burners operating. To measure and adjust
the manifold pressure, use the following procedure.
1. Turn OFF gas to furnace at the manual gas shutoff valve
external to the furnace.
2. Turn off all electrical power to the system.
3. Back outlet pressure test screw (inlet/outlet pressure boss)
out one turn (counterclockwise, not more than one turn).
4. Attach a hose and manometer to the outlet pressure boss
of the valve.
5. Turn ON the gas supply.
6. Turn on power and energize main (M) solenoid. Do not
energize the (HI) solenoid.
7. Measure gas manifold pressure with burners firing. Adjust
manifold pressure using the Manifold Gas Pressure table
shown below.
8. Remove regulator cover screw from the low (LO) outlet
pressure regulator adjust tower and turn screw clockwise
to increase pressure, or counterclockwise to decrease
pressure.
9. Energize main (M) solenoid as well as the (HI) terminal.
10. Remove regulator cover screw from the (HI) outlet pressure
regulator adjust tower and turn screw clockwise to increase
pressure, or counterclockwise to decrease pressure.
11. Turn off all electrical power and gas supply to the system.
12. Remove manometer hose from outlet pressure boss.
4. Calculate the furnace input in BTUs per hour (BTU/ hr). Input
equals the installation’s gas heating value multiplied by a
conversion factor (hours to seconds) divided by the number
of seconds per cubic foot. The measured input must not be
greater than the input indicated on the unit rating plate.
EXAMPLE:
Installation’s gas heating (HTG) value: 1,000 BTU/ft 3
(Obtained from gas supplier)
Installation’s seconds per cubic foot: 34 sec/ ft3
Conversion Factor (hours to seconds): 3600 sec/hr
Input = (Htg. value x 3600) ÷ seconds per cubic foot
Input = (1,000 BTU/ft3 x 3600 sec/hr) ÷ 34 sec/ ft3
Input = 106,000 BTU/hr
This measured input must not be greater than the input
indicated on the unit rating plate.
5. Turn ON gas and relight appliances turned off in step 1.
Ensure all the appliances are functioning properly and that
all pilot burners are operating.
TEMPERATURE RISE
Temperature rise must be within the range specified on the unit
rating plate. An incorrect temperature rise may result in condensing in or overheating of the heat exchanger. An airflow and temperature rise table is provided in the Product Data Book applicable
to your model. Determine and adjust temperature rise as follows:
28
5. Turn ON power to furnace.
6. Verify proper temperature rise as outlined in Section XIV,
Startup Procedure and Adjustment - Temperature Rise.
1. Operate furnace with burners firing for approximately ten
minutes. Ensure all registers are open and all duct
dampers are in their final (fully or partially open) position.
2. Place thermometers in the return and supply ducts as close
to the furnace as possible. Thermometers must not be
influenced by radiant heat by being able to “see” the heat
exchanger.
Circulator Blower Speeds
Low
Red
Medium Low
Orange
Medium
Blue
Black
High
White
Common/Neutral
HEAT EXCHANGER
RADIATION "LINE OF SIGHT"
SUPPLY
AIR
T SUPPLY
XV. NORMAL SEQUENCE OF OPERATION
POWER UP
RISE =
TSUPPLY
-
T RE TURN
The normal power up sequence is as follows:
• 115 VAC power applied to furnace.
T RETURN
RETURN
AIR
Temperature Rise Measurement
3. Subtract the return air temperature from the supply air
temperature to determine the air temperature rise. Allow
adequate time for thermometer readings to stabilize.
4. Adjust temperature rise by adjusting the circulator blower
speed. Increase blower speed to reduce temperature rise.
Decrease blower speed to increase temperature rise. Refer
to Section XIV, Startup Procedure and Adjustment -Circulator
Blower Speeds for speed changing details.
•
•
•
Integrated control module performs internal checks.
•
Furnace awaits call from thermostat.
Integrated control module LED will light.
Integrated control module monitors safety circuits
continuously.
HEATING MODE
(MODE DIP SWITCH IS SET TO “1 STG” POSITION)
The normal operational sequence in heating mode is as follows:
• R and W thermostat contacts close, initiating a call for heat.
CIRCULATOR BLOWER SPEEDS
WARNING
•
•
Integrated control module performs safety circuit checks.
•
•
Igniter warm up begins after 15 second prepurge expires.
•
Integrated control module monitors flame presence. Gas
valve will remain open only if flame is detected.
•
Circulator blower is energized on high heat speed following
a fixed thirty second blower on delay. Electronic air cleaner
terminals are energized with circulator blower.
•
Furnace operates; integrated control module monitors
safety circuits continuously.
•
R and W thermostat contacts open, completing the call for
heat.
•
•
Gas valve closes, extinguishing flame.
•
The circulator blower remains at high heat speed for thirty
seconds. The circulator blower then switches to low heat
speed for the remainder of the selected heat off delay period.
For example, the selected heat off delay period is 150
seconds. The circulator blower operates at high heat for 30
seconds and at low speed for 150 - 30 = 120 seconds.
•
Furnace awaits the next call from thermostat.
TO PREVENT PREMATURE FAILURE OF HEAT EXCHANGER, PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH, DO NOT ADJUST THE LIMIT CONTROL (FACTORY
SET).
This furnace is equipped with a multi-speed circulator blower. This
blower provides ease in adjusting blower speeds. The Product
Data Book applicable to your model provides an airflow table, showing the relationship between airflow (CFM) and external static pressure (E.S.P.), for the proper selection of heating and cooling speeds.
The cooling blower speed is shipped set on HIGH, and the heating
blower speed is set as indicated in the Product Data Book applicable to your model. These blower speeds should be adjusted by
the installer to match the installation requirements so as to provide
the correct heating temperature rise and correct cooling CFM.
To adjust the circulator blower speed, proceed as follows:
1. Turn OFF power to the furnace.
2. Select the heating and cooling blower speeds that match
the installation requirements from the airflow table in the
Product Data Book.
3. Relocate desired motor leads to the circulator blower heat
and cool speed terminals on the integrated control module.
(Terminals are identified as LO HEAT-H, HI HEAT-H and
COOL-H (hot)). If a heating speed and the cooling blower
speed are the same, a jumper wire must be used between
the heat and cool terminals.
4. Connect all unused blower motor leads to the “PARK”
terminals on the integrated control module. Any leads not
connected to the “PARK” terminals must be taped.
29
Induced draft blower is energized for 15 second prepurge
period causing pressure switch contacts to close.
Low and high stage gas valves open at end of igniter warm
up period, delivering gas to burners and establishing flame.
Induced draft blower is de-energized following a fifteen
second post purge.
(MODE DIP SWITCH IS SET TO “2 STG” POSITION)
The normal operational sequence in sequence is as follows:
• R and W thermostat contacts close, initiating a call for heat.
•
•
Integrated control module performs safety circuit checks.
•
•
Igniter warm up begins after 15 second prepurge expires.
Induced draft blower is energized for 15 second prepurge
period causing pressure switch contacts to close.
Low and high-stage gas valves open at end of igniter warm
up period, delivering gas to burners and establishing flame.
•
Furnace circulator blower and outdoor cooling unit run,
integrated control module monitors safety circuits
continuously.
•
R and Y thermostat contacts open, completing the call for
cool.
•
•
Outdoor fan and compressor are de-energized.
•
Furnace awaits the next call from thermostat.
Circulator blower is de-energized following a fixed forty five
second cool off delay period. Electronic air cleaner terminals
are de-energized.
•
High-stage gas valve closes after five seconds; low-stage
gas valve remains open.
FAN ONLY MODE
•
Integrated control module monitors flame presence. Gas
valve will remain open only if flame is detected.
The normal operational sequence in fan only mode is as follows:
• R and G thermostat contacts close, initiating a call for fan.
•
Circulator blower is energized on low heat speed following
a fixed thirty second blower on delay. Electronic air cleaner
terminals are energized with circulator blower.
•
•
Integrated control module performs safety circuit checks.
•
•
Furnace is now operating in low-stage heating mode.
•
Furnace operates; integrated control module monitors
safety circuits continuously.
Circulator blower runs, integrated control module monitors
safety circuits continuously.
•
•
If low-stage delay period expires, control will shift operation
from low-stage heating mode operation to high-stage
heating mode operation. Control will energize circulator
blower high heat speed and high stage gas valve.
R and G thermostat contacts open, completing the call for
fan.
•
Circulator blower is de-energized. Electronic air cleaner
terminals are de-energized.
•
Furnace awaits the next call from thermostat.
•
•
Furnace is now operating in high-stage heating mode.
•
Induced draft blower is de-energized following a fifteen
second post purge.
•
Circulator blower is de-energized following a heat off delay
period (selectable 100 or 150 seconds; factory set at 150
seconds).
If the furnace is operating in the low-stage heating mode
when thermostat contacts open, circulator remains at low
heat speed for the selected delay off period.
If the furnace is operating in high-stage heating mode when
the thermostat contacts open, the circulator blower remains
at high heat speed for thirty seconds. The circulator blower
then switches to low heat speed for the remainder of the
selected heat off delay period. For example, the selected
heat off delay period is 150 seconds. The circulator blower
operates at high heat for 30 seconds and at low speed for
150 - 30 = 120 seconds.
•
R and W thermostat contacts open, completing the call for
heat.
Circulator blower is energized on low heat speed. Electronic
air cleaner terminals are energized.
XVI. OPERATIONAL CHECKS
BURNER FLAME
The burner flames should be inspected with the burner compartment door installed. A sight glass is provided for inspection purposes. Flames should be stable, quiet, soft, and blue (dust may
cause orange tips but they must not be yellow). Flames should
extend directly outward from the burners without curling, floating, or
lifting off. Flames must not impinge on the sides of the heat exchanger firing tubes.
Check the burner flames for:
1. Good adjustment
2. Stable, soft and blue
3. Not curling, floating, or lifting off.
Furnace awaits the next call from thermostat.
Burner Flame
COOLING MODE
The normal operational sequence in cooling mode is as follows:
• R and Y thermostat contacts close, initiating a call for cool.
•
•
•
Integrated control module performs safety circuit checks.
Outdoor fan and compressor are energized.
Circulator blower is energized on cool speed following a
fixed five second on delay. Electronic air cleaner terminals
are energized with circulator blower.
XVII. SAFETY CIRCUIT DESCRIPTION
GENERAL
A number of safety circuits are employed to ensure safe and proper
furnace operation. These circuits serve to control any potential
safety hazards and serve as inputs in the monitoring and diagnosis of abnormal function. These circuits are continuously monitored during furnace operation by the integrated control module.
30
3. Service integrated control module or connecting wiring
following the discharge process in step 2. Use caution not
to recharge your body with static electricity; (i.e., do not move
or shuffle your feet, do not touch ungrounded objects, etc.).
If you come in contact with an ungrounded object, repeat
step 2 before touching control or wires.
4. Discharge your body to ground before removing a new
control from its container. Follow steps 1 through 3 if
installing the control on a furnace. Return any old or new
controls to their containers before touching any ungrounded
object.
INTEGRATED CONTROL MODULE
The integrated control module is an electronic device which, if a
potential safety concern is detected, the module will take the necessary precautions and provide diagnostic information through an
LED.
PRIMARY LIMIT
The primary limit control is located on the partition panel and monitors heat exchanger compartment temperatures. It is a normallyclosed (electrically), automatic reset, temperature-activated sensor. The limit guards against the overheating as a result of insufficient conditioned air passing over the heat exchanger.
DIAGNOSTIC CHART
AUXILIARY LIMIT
The auxiliary limit control(s) are located on or near the circulator
blower and monitors heat exchanger compartment temperatures.
They are a normally-closed (electrically), manual-reset, temperature activated sensors. These limits guard against overheating as
a result of insufficient conditioned air passing over the heat exchanger.
ROLLOUT LIMIT
WARNING
TO AVOID ELECTRICAL SHOCK, INJURY OR DEATH, DISCONNECT ELECTRICAL
POWER BEFORE PERFORMING ANY SERVICE OR MAINTENANCE.
Refer to the Troubleshooting Chart at the end of this manual for
assistance in determining the source of unit operational problems.
The red diagnostic LED blinks to assist in troubleshooting the unit.
The number of blinks refers to a specific fault code.
The rollout limit control(s) are mounted on the burner/manifold
assembly and monitor the burner flame. They are normally-closed FAULT RECALL
(electrically), manual-reset, temperature-activated sensors. These The ignition control is equipped with a momentary push-button
limits guard against burner flames not being properly drawn into switch that can be used to display on the diagnostic LED the last
the heat exchanger.
five faults detected by the control. The control must be in Standby
Mode (no thermostat inputs) to use the feature. Depress the pushPRESSURE SWITCHES
button switch for approximately 2 seconds. Release the switch
The pressure switches are normally-open (closed during opera- when the LED is turned off. The diagnostic LED will then display
tion), single-pole single-throw, negative air pressure-activated the flash codes associated with the last five detected faults. The
switches. They monitor the airflow (combustion air and flue prod- order of display is the most recent fault to the least recent fault.
ucts) through the heat exchanger via pressure taps located on the
induced draft blower and the coil front cover. These switches guard RESETTING FROM LOCKOUT
against insufficient airflow (combustion air and flue products)
Furnace lockout results when a furnace is unable to achieve ignithrough the heat exchanger and/or blocked condensate drain contion after three attempts during a single call for heat. It is characterditions.
ized by a non-functioning furnace and a one flash diagnostic LED
code. If the furnace is in “lockout”, it will (or can be) reset in any of
FLAME SENSOR
the following ways.
The flame sensor is a probe mounted to the burner/manifold as1. Automatic reset. The integrated control module will
sembly which uses the principle of flame rectification to determine
automatically reset itself and attempt to resume normal
the presence or absence of flame.
operations following a one hour lockout period.
2. Manual power interruption. Interrupt 115 volt power to the
XVIII. TROUBLESHOOTING
furnace for 1 - 20 seconds.
ELECTROSTATIC DISCHARGE (ESD) PRECAUTIONS
3. Manual thermostat cycle. Lower the thermostat so that
there is no longer a call for heat then reset to previous setting.
NOTE: Discharge body’s static electricity before touching unit. An
Interrupt thermostat signal to the furnace for 1 - 20 seconds.
electrostatic discharge can adversely affect electrical components.
Use the following precautions during furnace installation and ser- NOTE: If the condition which originally caused the lockout still
vicing to protect the integrated control module from damage. By exists, the control will return to lockout. Refer to Section XVIII,
putting the furnace, the control, and the person at the same electro- Troubleshooting - Diagnostic Chart for aid in determining the cause.
static potential, these steps will help avoid exposing the integrated
control module to electrostatic discharge. This procedure is applicable to both installed and uninstalled (ungrounded) furnaces.
1. Disconnect all power to the furnace. Do not touch the
integrated control module or any wire connected to the control
prior to discharging your body’s electrostatic charge to
ground.
2. Firmly touch a clean, unpainted, metal surface of the
furnaces near the control. Any tools held in a person’s
hand during grounding will be discharged.
31
XIX. MAINTENANCE
HORIZONTAL UNIT FILTER REMOVAL
Filters in horizontal installations are located in the central return
register or the ductwork near the furnace.
WARNING
To remove:
TO AVOID ELECTRICAL SHOCK, INJURY OR DEATH, DISCONNECT ELECTRICAL
1.
2.
3.
4.
POWER BEFORE PERFORMING ANY MAINTENANCE. IF YOU MUST HANDLE THE
IGNITER, HANDLE WITH CARE.
TOUCHING THE IGNITER ELEMENT WITH BARE
FINGERS, ROUGH HANDLING, OR VIBRATION COULD DAMAGE THE IGNITER
RESULTING IN PREMATURE FAILURE.
ONLY A QUALIFIED SERVICER SHOULD
EVER HANDLE THE IGNITER.
Turn OFF electrical power to furnace.
Remove filter(s) from the central return register or ductwork.
Replace filter(s) by reversing the procedure for removal.
Turn ON electrical power to furnace.
MEDIA AIR FILTER OR ELECTRONIC AIR CLEANER REMOVAL
ANNUAL INSPECTION
Follow the manufacturer’s directions for service.
The furnace should be inspected by a qualified installer, or service
agency at least once per year. This check should be performed at
the beginning of the heating season. This will ensure that all furnace components are in proper working order and that the heating
system functions appropriately. Pay particular attention to the following items. Repair or service as necessary.
• Flue pipe system. Check for blockage and/or leakage. Check
the outside termination and the connections at and internal
to the furnace.
BURNERS
•
INDUCED DRAFT AND CIRCULATOR BLOWERS
Heat exchanger. Check for corrosion and/or buildup within
the heat exchanger passageways.
•
Burners. Check for proper ignition, burner flame, and flame
sense.
•
Drainage system. Check for blockage and/or leakage.
Check hose connections at and internal to furnace.
•
Wiring. Check electrical connections for tightness and/or
corrosion. Check wires for damage.
•
Visually inspect the burner flames periodically during the heating
season. Turn on the furnace at the thermostat and allow several
minutes for flames to stabilize, since any dislodged dust will alter
the flames normal appearance. Flames should be stable, quiet,
soft, and blue (dust may cause orange tips but they must not be
yellow). They should extend directly outward from the burners without curling, floating, or lifting off. Flames must not impinge on the
sides of the heat exchanger firing tubes.
The bearings in the induced draft blower and circulator blower
motors are permanently lubricated by the manufacturer. No further
lubrication is required. Check motor windings for accumulation of
dust which may cause overheating. Clean as necessary.
CONDENSATE TRAP AND DRAIN SYSTEM (QUALIFIED SERVICER
ONLY)
Annually inspect the drain tubes, drain trap, and field-supplied drain
line for proper condensate drainage. Check drain system for hose
connection tightness, blockage, and leaks. Clean or repair as
necessary.
Filters.
FILTERS
FLAME SENSOR (QUALIFIED SERVICER ONLY)
CAUTION
TO ENSURE PROPER UNIT PERFORMANCE, ADHERE TO THE FILTER SIZES
GIVEN IN THE PRODUCT DATA BOOK APPLICABLE TO YOUR MODEL*.
MAINTENANCE
Improper filter maintenance is the most common cause of inadequate heating or cooling performance. Filters should be cleaned
(permanent) or replaced (disposable) every two months or as required. When replacing a filter, it must be replaced with a filter of
the same type and size.
FILTER REMOVAL
Depending on the installation, differing filter arrangements can be
applied. Filters can be installed in either the central return register
or a side panel external filter rack (upflow only). A media air filter or
electronic air cleaner can be used as an alternate filter. Follow the
filter sizes given in the Recommended Minimum Filter size table to
ensure proper unit performance.
To remove filters from an external filter rack in an upright upflow
installation, follow the directions provided with external filter rack
kit. To remove internal filters see Internal Filter Removal section.
Internal filters are an accessory item and are not included with
your furnace. For further details, see your distributor.
Under some conditions, the fuel or air supply can create a nearly
invisible coating on the flame sensor. This coating acts as an
insulator causing a drop in the flame sense signal. If the flame
sense signal drops too low the furnace will not sense flame and
will lock out. The flame sensor should be carefully cleaned by a
qualified servicer using emery cloth or steel wool. Following cleaning, the flame sense signal should be 1 to 6 microamps at 115
volts.
IGNITER (QUALIFIED SERVICER ONLY)
If the igniter and the surrounding air are at about 70°F and the
igniter wires are not connected to any other electrical components,
the resistance of the igniter should not exceed 75 ohms. If it does,
the igniter should be replaced.
FLUE PASSAGES (QUALIFIED SERVICER ONLY)
The heat exchanger flue passageways should be inspected at the
beginning of each heating season. If necessary, clean the passageways as outlined below.
32
1. Turn OFF the electrical power and gas supply to the furnace.
2. Disconnect the gas line and remove the burner/ manifold
assembly by removing the screws securing the assembly
to the partition panel.
3. Disconnect the flue pipe system from the induced draft
blower.
4. Remove the induced draft blower and, drain and pressure
tap hoses from the recuperator coil front cover.
5. Remove the recuperator coil front cover to expose the coil
tubes and turbulators.
6. Remove the recuperator coil turbulators individually by slowly
pulling each turbulator forward firmly.
7. Clean the recuperator coil tubes using a long handle wire
brush, such as a gun cleaning brush.
8. Clean the primary heat exchanger tubes using a wire brush
attached to a length of high grade stainless steel cable,
such as drain cleanout cable. Attach a variable speed
reversible drill to the other end of the cable. Slowly rotate
the cable with the drill and insert it into one of the heat
exchanger tubes. While reversing the drill, work the cable
in and out several times to obtain sufficient cleaning. Repeat
for each tube.
9. Clean residue from furnace using a vacuum cleaner.
10. Replace the parts removed in the previous steps in reverse
order.
11. Turn on electrical power and gas to furnace. Check for
leaks and proper unit operation.
12. Severe heat exchanger fouling is an indication of an
operational problem. Perform the checks listed in Section
XIV, Startup Procedure and Adjustments to reduce the
chances of repeated fouling.
Front of Furnace
Front of Furnace
Blower
Blower
6. Replace filter by reversing procedure.
XXI. BEFORE LEAVING AN INSTALLATION
•
Cycle the furnace with the thermostat at least three times.
Verify cooling and fan only operation.
•
Review the Owner’s Manual with the homeowner and
discuss proper furnace operation and maintenance.
•
Leave literature packet near furnace.
XXII. REPAIR & REPLACEMENT PARTS
•
When ordering any of the listed functional parts, be sure to
provide the furnace model, manufacturing, and serial
numbers with the order.
XX. INTERNAL FILTER REMOVAL
•
Internal filters are an accessory item and are not included with your
furnace. For further details, see your distributor.
Although only functional parts are shown in the parts list, all
sheet metal parts, doors, etc. may be ordered by description.
•
Parts are available from your distributor.
BOTTOM RETURN REMOVAL
1. Turn OFF electrical power to furnace.
2. Remove blower compartment door.
3. Push back and up on the wire filter retainer to release it
from under the front lip of the furnace basepan.
4. Slide filter forward and out.
5. Replace filter by reversing the procedure.
BLOWER COMPARTMENT REMOVAL
1. Turn OFF electrical power to furnace.
2. Remove blower compartment door.
3. Grasp lower portion of filter and lift up.
Front of Furnace
Blower
Blower
Filter
Front of Furnace
Functional Parts ListGas Valve
Gas Manifold
Natural Gas Orifice
Propane Gas Orifice
Igniter
Flame Sensor
Rollout Limit Switch
Primary Limit Switch
Auxiliary Limit Switch
Pressure Switch
Induced Draft Blower
Door Switch
Grab Here
And Lift
4. Angle filter toward the blower until filter clears bottom rail.
5. Lower filter down and pull outward.
33
Blower Motor
Blower Wheel
Blower Mounting Bracket
Blower Cutoff
Blower Housing
Capacitor
Heat Exchanger
Coil Front Cover
Integrated Control Module
Transformer
Troubleshooting Chart
Symptoms of Abnormal
Operation
Associated
Associated
LED
LED Code22
• Furnace fails to operate.
• Integrated control module
diagnostic LED provides
no signal.
NONE
• LED is Steady On.
ON
Fault Description(s)
Possible Causes
• No 115 volt power to • Manual disconnect switch
furnace, or no 24 volt OFF, door switch open, or
power to integrated
24 volt wires improperly
control module.
connected or loose.
• Blown fuse or circuit • Blown fuse or circuit
breaker.
breaker.
• Integrated control
module has an
internal fault.
• Integrated control module
has an internal fault.
• Normal Operation
•Normal Operation
• Furnace lockout due
to an excessive
number of ignition
“retries” (3 total)1.
• Failure to establish flame.
Cause may be no gas to
burners, front cover
pressure switch stuck open,
bad igniter or igniter
alignment, improper orifices,
or coated/oxidized or
improperly connected flame
sensor.
Corrective Action
Cautions and Notes
• Assure 115 and 24 volt • Turn power OFF
power to furnace
prior to repair.
integrated control module. • Replace integrated
• Check integrated control control module
module fuse (3A).
fuse with 3A
Replace if necessary.
automotive fuse.
• Check for possible shorts • Read precautions
in 115 and 24 volt circuits. in “Electrostatic
Repair as necessary.
Discharge” section
of manual.
• Replace bad integrated
control module.
• None
•Normal Operation
CONTINUOUS
ON
• Furnace fails to operate.
• Integrated control module
diagnostic LED is
flashing ONE (1) flash.
1
1 FLASH
• Loss of flame after establishment. Cause may be
interrupted gas supply, lazy
burner flames (improper gas
pressure or restriction in flue
and/or combustion air
piping), front cover pressure
switch opening, or improper
induced draft blower
performance.
• Induced draft blower
pressure switch contacts
sticking.
• Shorts in pressure switch
circuit.
• Replace induced draft • Turn power OFF
blower pressure switch. prior to repair.
• Replace pressure
switch with proper
• Repair short.
replacement part.
• Furnace fails to operate.
• Integrated control module
diagnostic LED is
flashing TWO (2) flashes.
• Pressure switch
circuit is closed.
• Induced draft
blower is not
2 FLASHES
operating.
• Induced draft blower runs
continuously with no
further furnace operation.
• Integrated control module
diagnostic LED is
flashing THREE (3)
flashes.
• Pressure switch
• Pressure switch hose
circuit not closed.
blocked, pinched or
• Induced draft blower connected improperly.
is operating.
• Blocked flue and/or inlet air
3 FLASHES
pipe, blocked drain system,
or weak induced draft
blower.
• Incorrect pressure switch
setpoint or malfunctioning
switch contacts.
• Loose or improperly
connected wiring.
2
• Turn power
OFF prior to
repair.
• Locate and correct gas
interruption.
• Check front cover
pressure switch
operation (hose, wiring,
contact operation).
Correct if necessary.
• Replace or realign
igniter.
• Check flame sense
signal. Sand sensor if
coated and/or oxidized.
• Check flue piping for
blockage, proper
length, elbows, and
termination.
• Verify proper induced
draft blower performance.
3
1
• Inspect pressure
• Turn power
switch hose. Repair, if
OFF prior to
necessary,
repair.
• Inspect flue and/or inlet • Replace
air piping for blockage,
pressure
proper length, elbows,
switch with
and termination. Check proper
drain system. Correct
replacement
as necessary.
part.
• Correct pressure switch
setpoint or contact
motion.
• Tighten or correct
wiring connection.
Integrated control module will automatically attempt to reset from lockout after one hour.
LED Flash code will cease if power to the control module is interrupted through the disconnect or door switch.
2
34
• Igniter is
fragile, handle
with care.
• Sand flame
sensor with
emery cloth.
• See “Vent/Flue
Pipe” section
for piping
details.
Troubleshooting Chart
Symptoms of Abnormal
Operation
Associated
LED Code2
• Circulator blower runs
continuously. No furnace
4
operation.
• Integrated control module 4 FLASHES
diagnostic LED is
flashing FOUR (4)
flashes.
Fault Description(s)
• Primary or auxiliary
limit circuit is open.
Possible Causes
• Insufficient conditioned air
over the heat exchanger.
Blocked filters, restrictive
ductwork, improper
circulator blower speed, or
failed circulator blower.
• Faulty primary or auxiliary
limit switch.
• Loose or improperly
connected wiring.
Corrective Action
Cautions and Notes
• Check primary/
auxiliary limit. Replace
if necessary.
• Check filters and
ductwork for blockage. Clean filters or
remove obstruction.
• Check circulator
blower speed and
performance. Correct
speed or replace
blower if necessary.
• Tighten or correct
wiring connection.
• Turn power OFF
prior to repair.
• Replace primary/
auxiliary switch
with proper
replacement part.
• Replace blower
with correct
replacement part.
• Induced draft blower,
• Flame sensed with
and circulator blower
no call for heat.
5
runs continuously. No
furnace operation.
5 FLASHES
• Integrated control module
diagnostic LED is
flashing FIVE (5) flashes.
• Short to ground in flame
sense circuit.
• Correct short at flame
sensor or in flame
sensor wiring.
• Turn power OFF
prior to repair.
• Circulator blower runs
• Rollout limit circuit is
continuously. No furnace
open.
6
operation.
• Integrated control
• Integrated control module 6 FLASHES
module fuse is
diagnostic LED is
blown.
flashing SIX (6) flashes.
• No furnace operation.
• Flame rollout.
• Misaligned burners, blocked
flue and/or air inlet pipe, or
failed induced draft blower.
• Loose or improperly
connected wiring.
• Faulty rollout limit.
• Short in 24 volt AC control
circuits or safety circuits.
• Check burners for
proper alignment.
• Check flue and air inlet
piping for blockage,
proper length, elbows,
and termination.
Correct as necessary.
• Check induced draft
blower for proper
performance. Replace,
if necessary.
• Tighten or correct
wiring connection.
• Repair short in 24 volt
AC control/safety
circuit(s)
• Replace integrated
control module fuse
(3A).
• Turn power OFF
prior to repair.
• See “Vent/Flue
Pipe” section for
piping details.
• Replace rollout limit
with correct
replacement part.
• Replace induced
draft blower with
correct replacement part.
• Replace integrated
control module
fuse with 3A
automotive fuse.
• Read precautions
in “Electrostatic
Discharge” section
of manual
• Normal furnace
operation.
• Integrated control
module diagnostic
LED is flashing
SEVEN (7) flashes.
• Furnace fails to
operate.
• Integrated control
module diagnostic LED
is flashing continuously.
7
• Flame sense
microamp signal is
low.
7 FLASHES
C
CONTINUOUS/
RAPID FLASH
• Polarity of 115 or 24
volt power is
reversed.
• Flame sensor is coated/
oxidized.
• Flame sensor incorrectly
positioned in burner flame.
• Lazy burner flame due to
improper gas pressure or
combustion air.
• Polarity of 115 volt AC
power to furnace or
integrated control module is
reversed.
• Orange and gray wires to
transformer are reversed.
• Poor unit ground.
2
• Sand flame sensor if
coated/oxidized.
• Inspect for
proper sensor
alignment.
• Check inlet air piping
for blockage, proper
length, elbows, and
termination.
• Compare current gas
pressure to rating plate
info. Adjust as needed.
• Review wiring diagram
to correct polarity.
• Reverse orange and
gray wires connected
to transformer.
• Verify proper ground.
Correct if necessary.
LED Flash code will cease if power to the control module is interrupted through the disconnect or door switch.
35
• Turn power OFF
prior to repair.
• Sand flame sensor
with emery clot.
• See “Vent/Flue
Pipe” section for
piping details.
• See rating plate for
proper gas
pressure.
• Turn power OFF
prior to repair.
WIRING DIAGRAM
AMH95
BLOWER
COMPARTMENT
DOOR SWITCH
(OPEN WHEN
DOOR OPEN)
OR
24 VAC
HUMIDIFIER
GY
24 VAC
INTEGRATED
CONTROL MODULE
HUMIDIFIER
TR (6)
GND
GND (8)
C
MVC (9)
115 VAC
24V THERMOSTAT
CONNECTIONS
PM
G
C
R
BK
GY
INTEGRATED
CONTROL
MODULE
OFF
2ND
STAGE
DELAY
MODE
HEAT
OFF
DELAY
*
*
6
5
4
8
7
BL
12
11
10
YL
HEAT-H
HLO (1)
R
RO2 (11)
RO1 (5)
24 VAC
40 VA
TRANSFORMER
WH
XFMR-H
WH
HOT SURFACE
IGNITER
IGN
OR
GY
OR
BL
BR
YL
HE LO
AT
-H
COOL-H
PU
BLOWER COMPARTMENT
EAC-H
MANUAL RESET
AUXILIARY LIMITS
(1) IN UPFLOW
BLOW ER DECK
(2) IN C'FLOW
BLOW ER HOUSING
BURNER COMPARTMENT
GND
BK
CIRCULATOR
BLWR
CIR-N
H I -H
AT
HE
OR
WH
CAPACITOR
ID-N
ID
BLWR
IND
ELECTRONIC
AIR CLEANER
INTEGRATED CONTROL MODULE
INTEGRATED CONTROL MODULE
GR
RD
WH
BK
BR
XFMR-N
FS
PK
RD
115 VAC
FLAME SENSOR
YL
BK (HI)
BL (MED)
OR (MED LOW)
RD (LOW)
TO AVOID POSSIBLE ELECTRICAL SHOCK, PERSONAL INJURY,
OR DEATH, DISCONNECT THE POWER BEFORE SERVICING.
HLI (7)
W
BK
LINE-H
SEE
NOTE 4
NO
C
PSO (4)
TH (3)
WH
! WARNING
PS (10)
TO
MICRO
Y
PK
XFMR-H
1
SEE
NOTE 6
GND
G
BR
115 VAC NEUTRAL
TERMINALS
FS
2
COOL-H
GR
OR
OR
ID BLOWER
PRESSURE
SW ITCH
XFMR-N
115 VAC HOT AND PARK TERMINALS
*
OR
RD
GY
OR
*
PK
9
GY
FACTORY SETTINGS
SHOWN
DIAGNOSTIC
LED
1
2
24V THERMOSTAT CONNECTIONS
OR
3
C
NO
FRONT COVER
PRESSURE SWITCH
BK
WH
FUSE
ON
MVL(2)
C
W Y
BK
BR
GAS
HI VALVE
MVH (12)
EAC-N
LINE-N
LINE-H
JUNCTION BOX
DOOR
SWITCH
WH
WH
INDUCED DRAFT
BLOWER
DISCONNECT
WH
PU
BL
L
YL
RD
N
O
GND
N
TO 115VAC/ 1 Ø /60 HZ POWER SUPPLY WITH
OR
OR
OVERCURRENT PROTECTION DEVICE
C
PK
RD
WH
ID BLOWER
24 VAC
PRESSURE
HUMIDIFIER
SWITCH
2 CIRCUIT
CONNECTOR
HOT
SURFACE
IGNITER
0
PM
BL
N
O
C
GY
1
FRONT COVER
PRESSURE SWITCH
GY
GND
C
2
HI
3
JUNCTION
BOX
WH
GR
BR
BK
OR
GAS VALVE
STEADY ON = NORMAL OPERATION
LOW VOLTAGE (24V)
= CONTROL FAILURE
1
1 FLASH
=
2
2 FLASHES = PRESSURE SWITCH STUCK CLOSED
HI VOLTAGE (115V)
3
3 FLASHES = PRESSURE SWITCH STUCK OPEN
HI VOLTAGE FIELD
4
4 FLASHES = OPEN HIGH LIMIT
LOW VOLTAGE FIELD
5 FLASHES = FLAME SENSE WITHOUT GAS VALVE
6
6 FLASHES =
7
7 FLASHES = LOW FLAME SIGNAL
C
CONTINUOUS/RAPID FLASHES = REVERSED 115 VA C POLARITY
0140F00098 REV.--
EQUIPMENT GND
FIELD GND
FIELD SPLICE
SWITCH (TEMP.)
JUNCTION
5
PK PINK
BR BROWN
WH WHITE
BL BLUE
GY GRAY
RD RED
L
FLAME
SENSOR
OFF
COLOR CODES:
YL YELLOW
OR ORANGE
PU PURPLE
GN GREEN
BK BLACK
N
GND
TERMINAL
INTERNAL TO
INTEGRATED CONTROL
PLUG CONNECTION
IGNITER
SWITCH (PRESS.)
OVERCURRENT
PROT. DEVICE
NOTES:
1. SET HEAT ANTICIPATOR ON ROOM THERMOSTAT AT 0.7 AMPS.
2. MANUFACTURER'S SPECIFIED REPLACEMENT PARTS MUST BE USED WHEN SERVICING.
3. IF ANY OF THE ORIGINAL WIRE AS SUPPLIED WITH THE FURNACE MUST BE REPLACED, IT MUST BE REPLACED WITH WIRING MATERIAL
HAVING A TEMPERATURE RATING OF AT LEAST 105 °C. USE COPPER CONDUCTORS ONLY.
4. IF HEATING AND COOLING BLOWER SPEEDS ARE NOT THE SAME, DISCARD JUMPER BEFORE CONNECTING BLOWER LEADS. UNUSED
BLOWER LEADS MUST BE PLACED ON "PARK" TERMINALS OF INTEGRATED CONTROL OR TAPED.
5. UNIT MUST BE PERMANENTLY GROUNDED AND CONFORM TO N.E.C. AND LOCAL CODES.
6. TO RECALL THE LAST 5 FAULT S, MOST RECENT TO LEAST RECENT, DEPRESS SWITCH FOR MORE THAN 2 SECO NDS WHILE IN
STANDBY (NO THE RMOSTAT IN PUTS)
Wiring is subject to change, always refer to the wiring diagram on the unit for the most up-to-date wiring.
36
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement