User manual LCD 52

User manual LCD 52
LCD 52
User Interface
Operator’s Manual
Article # 60861910 / Edition 1.1
October 2001 / Printed in Germany
PROCESS PLC
Edition 1.1
Jetter AG reserves the right to make alterations to its products in the interest of
technical progress. These alterations need not be documented in every single case.
This manual and the information contained herein have been compiled with due
diligence. However, Jetter AG assumes no liability for printing or other errors or
damages arising from such errors.
The brand names and product names used in this document are trademarks or
registered trademarks of the respective title owner.
2
Jetter AG
PROCESS PLC
How to Contact us:
Jetter AG
Gräterstrasse 2
D-71642 Ludwigsburg
Germany
Phone - Switchboard:
Phone - Sales:
Phone - Technical Hotline:
+49 7141 2550-0
+49 7141 2550-530
+49 7141 2550-444
Telefax:
E-Mail - Sales:
E-Mail - Technical Hotline:
Internet Address:
+49 7141 2550-425
[email protected]
[email protected]
http://www.jetter.de
This Operator’s Manual is an Integral
Part of the LCD 52:
Model:
Serial No:
Year of Manufacture:
Order No.:
To be entered by the customer:
Inventory No:
Place of operation:
© Copyright 2001 by Jetter AG. All rights reserved.
Jetter AG
3
PROCESS PLC
Significance of this Operator’s Manual
This manual is an integral part of the LCD 52 user interface, and
•
•
must be kept in a way that it is always at hand until the LCD 52 user interface will
be disposed of.
If the LCD 52 user interface is sold, alienated or loaned, this manual must be
handed over.
In any case you encounter difficulties to clearly understand the manual, please
contact the manufacturer.
We would appreciate any suggestions and contributions on your part and would ask
you to contact us. This will help us to produce manuals that are more user-friendly
and to address your wishes and requirements.
Unavoidable residual hazards for persons and material may result from the LCD 52
user interface. For this reason, any person who has to deal with the operation,
transport, installation, maintenance and repair of the LCD 52 user interface must
have been familiarised with it and must be aware of these dangers.
Therefore, this person must carefully read, understand and observe this manual, and
especially the safety instructions.
Missing or inadequate knowledge of the manual results in the loss of any claim of
liability on part of Jetter AG. Therefore, the operating company is recommended to
have the instruction of the persons concerned confirmed in writing.
4
Jetter AG
LCD 52
Table of Contents
Table of Contents
1
Safety Instructions
7
2
Installing the User Interface
12
3
Setting Up the User Interface
in Multi-Display Mode
15
4
Operating Conditions
18
5
Physical Dimensions
20
6
Technical Data
21
7
Display and Key Functions
22
List of Appendices
Appendix A:
Appendix B:
Appendix C:
Appendix D:
Jetter AG
Glossary
List of Abbreviations
List of Illustrations
Index
26
27
28
29
5
Table of Contents
6
PROCESS PLC
Jetter AG
LCD 52
1 Safety Instructions
Table
Contents
of
1
Safety Instructions
The LCD 52 user interface is in line with the current state of the art. The LCD 52 user
interface complies with the valid safety regulations and standards. Special emphasis
was given to the safety of the users.
Of course, the following regulations apply to the user:
•
•
•
relevant accident prevention regulations;
accepted safety rules;
EC guidelines and other country-specific regulations.
Usage as Agreed Upon
Usage as agreed upon includes operation in accordance with the operating
instructions.
The LCD 52 user interface is designed and approved for operation in an electric
cabinet only. The LCD 52 only works together with a PROCESS-PLC by Jetter AG.
The user interface LCD 52 serves to control machinery such as dosing and
hardening equipment, stage technique and logistic centres.
Usage Other Than Agreed Upon
The LCD 52 user interface must not be used in technical systems which to a high
degree have to be fail-safe, e.g. ropeways and aeroplanes. If the LCD 52 user
interface is to be run under operating conditions, which differ from the conditions
mentioned in chapter 4, page 18, the manufacturer is to be contacted beforehand.
Who is Permitted to Operate the LCD 52 User Interface?
Only instructed, trained and authorised persons are permitted to operate the LCD 52
user interface.
Mounting and backfitting may only be carried out by specially trained personnel, as
specific know-how will be required.
Maintaining the LCD 52 User Interface
The LCD 52 user interface is maintenance-free. Therefore, no inspection or
maintenance are required for the operation of the module.
Decommissioning and Disposing of the LCD 52
User Interface
Decommissioning and disposing of the LCD 52 user interface are subject to the
environmental legislation of the respective country in effect for the operator's
premises.
Jetter AG
7
1 Safety Instructions
PROCESS PLC
Description of Symbols
This sign is to indicate a possible impending danger of serious injury or death.
Danger
This sign is to indicate a possible impending danger of light injury. This sign is
also to warn you of material damage.
Caution
This sign is to indicate a possible impending situation which might bring damage
to the product or to its surroundings.
Important
This sign is to indicate an application, e.g installation, and other useful
information.
Note
· / -
Enumerations are marked by full stops, strokes or scores.
Operating instructions are marked by this arrow.
Automatically running processes or results to be achieved are marked by this
arrow.
Keys on the user interface.
8
Jetter AG
LCD 52
1 Safety Instructions
Ensure Your Own Safety
Isolate the LCD 52 user interface or the PROCESS-PLC from the mains, if
maintenance works have to be carried out. By doing so, you will prevent accidents
resulting from electric voltage and moving parts.
Modifications and Alterations to the Module
•
For safety reasons, no modifications and changes to the LCD 52 user interface
and its functions are permitted. Any modifications to the LCD 52 user interface not
expressly authorised by the manufacturer will result in a loss of any liability claims
to Jetter AG.
•
The original parts are specifically designed for the LCD 52 user interface . Parts
and equipment of other manufacturers are not tested on our part, and are
therefore not released by us. The installation of such parts may impair the safety
and the proper functioning of the LCD 52 user interface .
•
For any damages resulting from usage other than agreed upon, e.g. the use of
non original parts and equipment, any claims with respect to liability of Jetter AG
are excluded.
Malfunctions
Malfunctions or other damages are to be reported to an authorised person
immediately.
Safeguard the LCD 52 user interface against misuse or accidental use.
Only qualified experts are allowed to carry out repairs.
Safety and protective devices, e.g. the barrier and cover of the terminal box
must not in any case be shunted or by-passed.
Dismantled safety devices must be reattached prior to commissioning and
checked for proper functioning.
Information Signs and Labels
Writings, information signs, and labels always have to be observed and
kept readable.
Damaged or unreadable information signs and labels are to be exchanged.
Jetter AG
9
1 Safety Instructions
PROCESS PLC
Instructions on EMI
The noise immunity of a system corresponds to the weakest component of the
system. For this reason, correct wiring and shielding of the cables is important.
Important!
Measures for increasing immunity to interference:
Only use originally shielded cables as bus cables.
Both sides of the cables must be shielded.
The entire shield must be drawn behind the isolation, and then be
clamped under a strain relief with the greatest possible surface area.
When connecting the signal line to the terminal block it is important
that the strain relief is directly connected to a grounded surface with the
greatest possible surface area.
When using connectors, metallised connectors are to be used only,
e.g. SUB-D connectors with metallised housing according to Fig. 1.
Make sure that the strain relief is directly connected with the housing
here as well.
Male/Female SUB-D Connectors (9, 15 or 25 Pins) with
Metallised Housing
Fig. 1: Shielding in Conformity with EMC Standards
10
Jetter AG
LCD 52
1 Safety Instructions
Important!
To avoid malfunctions the following must be ensured:
The shielding must be clamped under a strain relief with the greatest
possible surface area.
The distance between unshielded conductor ends must be as short as
possible.
Residual Dangers
Hazards during Operation
Danger resulting from electric shock!
If the LCD 52 is not connected-up correctly or is not isolated from the mains, for
example during installation, maintenance, and repair, you can get an electric
shock.
Please observe the following precautions in order to avoid injuries such as
muscle cramps, burns, unconsciousness, respiratory standstill, and possibly
death:
Isolate the LCD 52 from the mains (pull out the mains plug) when
working on the control system.
Do not touch the female connectors during operation.
Have works on the electric and electronic system performed by
qualified personnel only.
Jetter AG
11
2 Installing the User Interface
2
PROCESS PLC
Installing the User Interface
Scope of Delivery
•
•
LCD 52 User Interface
Operator's Manual
Installation Steps
Please check the delivery package for completeness and make sure that
the LCD 52 is not damaged.
Connect the LCD 52 user interface to your control system (LCD port) with
the user interface cable.
Connect the control system, for example a NANO-B, to your computer with
the programming cable EM-PK.
Activate the control system and load a program, for example a SYMPAS
program, from your computer to your PROCESS-PLC.
Check the function of the control system.
Fig. 2: Example: Connection of LCD 52 with PROCESS-PLC NANO-B
12
Jetter AG
LCD 52
2 Installing the User Interface
Mounting and Startup Accessories
(not included in the scope of delivery)
•
•
•
•
Programming cable EM-PK, 0.5 m, 2.5 m or 5 m
Wall mounting holder LCD 52-H
Computer
PROCESS-PLC
Troubleshooting
Check whether the programming cable EM-PK and the user interface
cables are connected properly according to the manual.
Check the function of the user interface with your control system.
Notes on Safety as regards the Installation
Danger resulting from electric shock!
If the digital LCD 52 user interface is not isolated from the mains, for example
during installation, maintenance, and repair, you can get an electric shock.
Please observe the following precautions in order to avoid injuries such as
muscle cramps, burns, unconsciousness, respiratory standstill, and possibly
death:
Have works on the electric and electronic system performed by
qualified personnel only.
Isolate the LCD 52 from the mains (pull out the user interface cable)
when working on the control system.
Prior to commissioning, please do the following:
Jetter AG
•
Reattach dismantled safety equipment and check it for proper
functioning.
•
Secure the LCD 52 against accidental contact with conductive parts
and components.
•
Only connect units or electric components with the signal lines of the
LCD 52 user interface when they are insulated properly against the
connected electric circuit.
•
Establish a permanent connection from the LCD 52 to the
PROCESS-PLC with the user interface cable DK-422, see Fig. 2,
page 12.
13
2 Installing the User Interface
PROCESS PLC
Important
Never plug or unplug the user interface cable of the LCD 52 when the
controller is switched on.
Doing so could damage the LCD 52 unser interface.
Therefore, only carry out installation and maintenance work at the LCD 52 user
interface when the controller is isolated from the mains.
14
Jetter AG
LCD 52
3 Setting Up the User Interface in Multi-Display Mode
3
Setting Up the User Interface in
Multi-Display Mode
Fig. 3: Flow Chart of LCD Parameterizing
Jetter AG
15
3 Setting Up the User Interface in Multi-Display Mode
PROCESS PLC
By means of the multi-display mode, up to four LCD user interfaces can be operated
by a PROCESS-PLC of the NANO-A, NANO-B, NANO-C, DELTA or any other type
which is able to process the pcom5 protocol. Identical or different texts and/or
register contents can be displayed.
The parameters of the LCD 52 user interface are to be entered as shown in
the flow chart on Fig. 3, page 15.
An individual number must be assigned to each LCD user interface.
If only one LCD user interface is used, value 0 is always assigned.
If more than one LCD user interface is used, a value in ascending order
between 1 and 4 is assigned to each LCD user interface; a display with the
number 1 is obligatory.
The display with number 1 is the master LCD. After power up, only the first LCD user
interface is synchronized with the PROCESS-PLC. The other LCDs remain inactive
until they receive command signals.
Note!
Simultaneous function of both user input and monitor mode is only possible on
one display.
Note!
•
•
•
•
•
The voltage for several LCD user interfaces cannot be supplied anymore from
the controller only.
Therefore, the LCD user interfaces need to be supplied by a separate power
supply with a DC voltage of 15 V to 30 V.
Each LCD 52 user interface has a current consumption of about 200 mA.
An adapter or modified connection cables are necessary to connect several
user interfaces to the LCD interface of the PROCESS-PLC.
Different from the standard design, the connection cables must be altered, see
Fig. 4, page 17.
Note!
Only user interfaces with RS 422 interface can be used in multi-display mode.
16
Jetter AG
LCD 52
3 Setting Up the User Interface in Multi-Display Mode
Fig. 4: PIN Assignment of the Connecting Cable for Several LCD
User Interfaces
Important!
•
When fabricating the connecting cable, the following minimum requirements
apply (also for EMC):
1. Number of cores:
•
Jetter AG
6
2. Core cross-sectional area:
0.25 mm²
3. Connector (male):
Sub-D, metallised
4. Max. cable length:
100 m
5. Shield:
complete shielding, no paired shielding
The shield must be connected to the metallised connector housings on both
ends of the cable with the greatest possible surface area.
17
4 Operating Conditions
PROCESS PLC
4
Operating Conditions
Environmental Operating Parameters
Parameter
Value
Operating
Temperature Range
0 °C up to + 50 °C with
max. 3 K/min
Storage Temperature
Range
-10 °C (max. 48 h) up to + 70 °C
(max. 168 h)
Air Humidity /
Humidity Rating
5 % to 90 %, non-condensing
Pollution Degree
II
Corrosion Immunity/
Chemical Resistance
No special protection against
corrosion. Ambient air must be
free from higher concentrations of
acids, alcaline solutions, corrosive
agents, salts, metal vapours, or
other corrosive or
electroconductive contaminants.
Operating Altitude
Max. 2000 m above sea level
Reference
DIN EN 60068-2-1
DIN EN 60068-2-2
DIN EN 61131-2
DIN EN 61131-2
Mechanical Operating Parameters
Parameter
Value
Reference
Free Falls
Withstanding Test
Height of fall (units within packing):
1m
DIN EN 60068-2-32
Vibration Resistance
0.5 g constant acceleration for
continuous operation, all 3 spatial
axes
Technical Data of
the LCD Display
Shock Resistance
3 3 g occasionally, all 3 spatial
axes
Technical Data of
the LCD Display
Degree of Protection
IP 65
EN 60529
Mounting Position
unassigned
Electrical Safety Operating Parameters
Parameter
18
Value
Reference
Protection Class
III
DIN EN 61131-2
Overvoltage
Category
II
DIN EN 50178
Jetter AG
LCD 52
4 Operating Conditions
EMC - Emitted Interference Operating Parameters
Parameter
Enclosure
Value
•
•
Frequency band 30 MHz to 230
MHz, limit 30 dB (µV/m)
at 10 m distance
Frequency band 230 MHz to
1000 MHz, limit 37 dB (µV/m)
at 10 m distance
(class B)
Reference
DIN EN 50081-1
DIN EN 50081-2
DIN EN 55011
EMC - Immunity to Interference Operating Parameters
Interference Immunity: Enclosure
Parameter
Value
Reference
Electromagnetic RF
Field
amplitude-modulated
Frequency band 27 -1000 MHz;
test signal strength 10 V/m
AM 80 % with 1 kHz
Criterion A
DIN EN 61000-6-2
DIN EN 61131-2
DIN EN 61000-4-3
Magnetic Field with
Mains Frequency
50 Hz
30 A/m
DIN EN 61000-6-2
DIN EN 61000-4-8
ESD
Discharge through air:
Test peak voltage 15 kV (Humidity
Rating RH-2 / ESD-4)
Contact discharge:
Test peak voltage 4 kV
(severity level 2)
Criterion A
DIN EN 61000-6-2
DIN EN 61131-2
DIN EN 61000-4-2
Interference Immunity: Signal Ports
Parameter
Jetter AG
Value
Reference
Asymmetric RF,
amplitude-modulated
Frequency 0.15 - 80 MHz
Test voltage 10 V
AM 80 % with 1 kHz
Source impedance 150 Ω
Criterion A
DIN EN 61000-6-2
DIN EN 61000-4-6
Burst
Test voltage 1 kV
tr/tn 5/50 ns
Repetition rate 5 Hz
Criterion A
DIN EN 61000-6-2
DIN EN 61131-2
DIN EN 61000-4-4
19
5 Physical Dimensions
5
PROCESS PLC
Physical Dimensions
Fig. 5: Physical Dimensions LCD 52
20
Jetter AG
LCD 52
6 Technical Data
6
Technical Data
General and Mechanical Specification
Height
211 mm
Width
100 mm
Depth
26 mm
Screen size
62 mm x 25 mm
Number of lines
4
Number of characters per line
16
Character height
4.74 mm
Weight
approx. 275 g
Keys
•
•
6 function keys
15 entry keys
Touch pad panel:
Lifetime of the keys
> 1 mio. operations
Switching pressure
3N
Contact areas
Gold-coated snap connections
Cable:
Cable length
3 m, 5 m or 7 m (shielded)
Cable material
LIYCY 7 x 0.25 mm²
Color of the cable / special
features
RAL 7032, apt for drag chains
Electrical Specification
Power supply
DC 24 V(12 V... 30 V) via the 15-pin
user interface cable
Please refer to "Note!"
Power consumption
– max. 200 mA
– typically 85 mA at 12 V and 20 °C
– typically 40 mA at 24 V and 20 °C
Display
LCD IF
Interfaces
15-pin SUB-D connector: RS422
Note!
Disconnection from the power supply leads to a reset of the LCD 52.
Jetter AG
21
7 Display and Key Functions
PROCESS PLC
7
Display and Key Functions
The function keys are user-programmable. They are used to display masks and/or
activate control functions.
Note!
For a detailed description on how to configure registers and flags, please refer to
the operator’s manual of NANO-A, NANO-B, NANO-C, Delta or respective other
controller.
Flag Assignment of Keys
Flag
Key
Flag
2201
2162
2202
2163
2203
2164
2204
2165
2216
2166
2215
2167
2218
2168
2217
2169
2219
2220
2160
2222
Key
2161
22
Jetter AG
LCD 52
7 Display and Key Functions
Note!
The F5 and F6 keys can only be used when the monitor mode of the controller in
use was deactivated. For more details on the use of the monitor mode, please
refer to the operator’s manual of the respective controller.
Important!
Please observe the following to avoid malfunctions and damage of the device:
Disable the monitor mode during operation of the LCD. The monitor
mode might change the state of the PROCESS-PLC. This way it is
possible, for example, to set outputs or write flags and registers during
operation.
Note!
Please take into account the following system characteristic of your
PROCESS-PLC that occurs in the battery-buffered flag range of the keypad:
•
The flags assigned to the keys are not automatically reset when the LCD 52 is
switched on.
•
When the LCD 52 is switched off while pressing a key, the corresponding flag
is set in the PROCESS-PLC when the LCD 52 is switched on again. This
applies whether the respective key is pressed or not.
•
In order to reset the flags assigned to the keys you can use e.g. the instruction
at the beginning of a SYMPAS program
CLEAR_FLAGS [2201 to 2222].
•
Jetter AG
Only use flags, e.g. in a SYMPAS program, that are not assigned to the
reserved flags of the LCD 52 keys.
23
7 Display and Key Functions
24
PROCESS PLC
Jetter AG
LCD 52
Appendices
Appendices
of
List
Appendices
Jetter AG
25
Appendices
PROCESS PLC
Appendices
of
List
Appendix A: Glossary
26
Baud rate
1 Baud = 1 signal change per second. The baud rate is
the number of signal changes that occur in one second,
not the number of bits per second transmitted.
DELTA
PROCESS-PLC by Jetter AG
Electromagnetic
Compatibility (EMC)
Definition according to EMC regulations: "EMC is the
ability of a device to function in a satisfactory way in
electromagnetic surroundings without causing
electromagnetic disturbances itself, which would be
unbearable for other devices in these surroundings."
Flag
1 bit storage position for intermediate results which are
required for linkage purposes.
The state of the bit is either 0 or 1.
Monitor Mode
This function allows to view and modify registers, I/Os,
etc. during operation.
NANO-A, NANO-B,
NANO-C
PROCESS-PLC by Jetter AG
pcom5
Communication protocol of Jetter AG
Process
A program or a part of it. A related sequence of steps
carried out by a program.
PROCESS-PLC
Advanced control system of JETTER AG in contrast to
the conventional programmable logic controller.
Register
A high-speed memory for a group of bits placed in a
microprocessor or in another electronic device where
data can be buffered for a specific purpose. On JETTER
controllers, usually, these are 24 bit wide storage
positions in a remanent RAM.
Jetter AG
LCD 52
Appendices
Appendix B: List of Abbreviations
Jetter AG
DC
Direct Current
DIN
Deutsches Institut für Normung = German Industry Standard
EMI
Electro Magnetic Compatibility
FSTN
Film Super Twisted Nematic
Gnd
Ground
Hz
Hertz
IEC
International Electrotechnical Commission
I/O
Input/Output
IP
International Protection
LC
Liquid Crystal
LCD
Liquid Crystal Display
LED
Light-Emitting Diode
PE
Protective Earth
PLC
Programmable Logic Controller
RDA
Receive Data A: First differential channel of the RS 422
interface
RDB
Receive Data B: Second differential channel of the RS 422
interface
RS 232
Accepted industry standard for serial data transmission.
RS: Recommended Standard
For line lengths under 15 m. No differential evaluation.
Transmitting and receiving on different lines.
RS 422
For line lengths over 15 m. Two differential evaluations each.
Transmitting and receiving on different lines.
RXD
Receive (RX) Data
A line used to carry received serial data from one device to
another.
SDA
Send Data A: First differential channel of the RS 422 interface
SDB
Send Data B: Second differential channel of the RS 422
interface
SUB-D
Type designation of connectors
TXD
Transmit (TX) Data
A line used to transmit received serial data from one device to
another; e.g. from a computer to a modem.
27
Appendices
PROCESS PLC
Appendix C: List of Illustrations
Fig. 1:
Fig. 2:
Fig. 3:
Fig. 4:
Fig. 5:
28
Shielding in Conformity with EMC Standards
Example: Connection of LCD 52 with
PROCESS-PLC NANO-B
Flow Chart of LCD Parameterizing
PIN Assignment of the Connecting Cable
for Several LCD User Interfaces
Physical Dimensions LCD 52
10
12
15
17
20
Jetter AG
LCD 52
Appendices
Appendix D: Index
D
Decommissioning and Disposing
DELTA
O
7
16
F
Flag
22
Function Keys
22
Operating Parameters
Electrical Safety
EMC - Emitted Interference
EMC - Immunity to Interference
Environment
Mechanics
18
19
19
18
18
P
I
Information Signs and Labels
Installation Steps
pcom5 Protocol
16
9
12
M
Maintenance
7
Malfunctions
9
R
Register
22
Residual Dangers
11
S
Metallised Connectors
10
Scope of Delivery
12
Metallised Housing
10
Shielding in Conformity with EMC
Standards
10
Modifications and Alterations
9
Monitor Mode
16
Mounting and Startup Accessories
12
Multi Display Mode
15
Symbols
8
T
Troubleshooting
13
N
NANO-B
Jetter AG
16
U
Usage as Agreed Upon
7
Usage Other Than Agreed Upon
7
29
Jetter AG
Gräterstrasse 2
D-71642 Ludwigsburg
Germany
Phone:
Fax:
Internet:
E-mail:
+49 7141 2550-530
+49 7141 2550-484
http://www.jetter.de
[email protected]
Subsidiaries
Jetter UK Ltd.
Jetter Asia Pte. Ltd.
Jetter AG Switzerland
43 Leighswood Road Aldridge
GB-West Midlands WS9 8AH
32 Ang Mo Kio Industrial Park 2
#07-03 Sing Industrial Complex
Singapore 569510
Münchwilerstrasse 19
CH-9554 Tägerschen
Great Britain
Singapore
Switzerland
Phone:
Fax:
E-mail:
Phone:
Fax:
E-mail:
Phone:
Fax:
E-mail:
+44 1922 745200
+44 1922 745045
[email protected]
+65 4838200
+65 4833881
[email protected]
+41 719 1879-50
+41 719 1879-69
[email protected]
Jetter USA Inc.
165 Ken Mar Industrial Parkway
Broadview Heights
OH 44147-2950
U.S.A
Phone:
Fax:
E-mail:
30
+1 440 8380860
+1 440 8380861
[email protected]
Jetter AG
Branches
Jetter AG Büro Nord
Jetter AG Büro Süd
Jetter AG Büro Mitte
Am Nordbahnhof 5
D-59555 Lippstadt
Am Pulverl 5
D-85051 Ingolstadt
Wohnbacher Strasse 19
D-61200 Wölfersheim
Germany
Germany
Germany
Phone:
Fax:
E-mail:
+49 2941 6691-10
+49 2941 6691-22
[email protected]
Phone:
Fax:
E-mail:
+49 841 97149-30
+49 841 97149-40
[email protected]
Jetter AG Büro Ost
Jetter AG Büro Netherlands
Gewerbepark am Wald 3d
D-98693 Ilmenau
Amperestraat 10
NL-4004 KB Tiel
Germany
Netherlands
Phone:
Fax:
E-mail:
Jetter AG
+49 3677 2000-54
+49 3677 2000-55
[email protected]
Phone:
Fax:
E-mail:
Phone:
+49 6036 3175
E-mail:
[email protected]
+31 344654-944
+31 344654-932
[email protected]
31
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement