S1333CM User Manual
WALLMOUNT LED THERMAL WATERFALL FAUCET
Dear Valued Customer,
SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. We welcome any questions or comments you may have and look forward to assisting you in the future.
SUMERAIN customer service department
1. Unpack your new product and ensure that all the parts are contained in the packaging. Keep the product in its original box until you ready to install it.
2. Shut off the water supply if replacing a previously-installed faucet.
3. Observe all plumbing and building codes in your area.
4. It is recommended that installation of the product be done by a professional plumber.
Tools you may need when installing the faucet
Number of Handles
Faucet Total Height
Faucet Body Material
Faucet Spout Material
Working water press
LED power supply
LED Color changing
Packing box size
Bathroom Sink Faucets
LED, Waterfall, Wall mount
180mm [7.1 Inch]
130mm [5.1 Inch]
0.2 ~0.8 Mpa
Water flow generator
< 28 ℃
28 ℃~ 38 ℃
> 38 ℃
305mm x 220mm x 155mm
CODE ITEM NAME QTY
A Faucet Body with panel 1 PCS
CODE ITEM NAME
C Thermostatic valve
H Plastic Expansion Nails 1 PCS
1 F Hoses
1 I Nut
Draw the straight line of position where need to install the faucet according to below dimension
Image 1: Front view
Dig hole “A” , hole “B” and hole “C” according to below dimension.
Image 2: Front view of digging hole
Beat the Plastic Expansion Nails into the hole “C” of wall
Rollback the Escutcheon and dismounting the Thermostatic valve “C” from assembled front panel.
Put the rubber ring into the handle hole of front panel and make it close with the panel.
Put the spout with front panel into digged hole of wall exactly and fasten it by screw.
Through the Thermostatic valve in the hole of wall and clockwise rotation into the rubber ring, adjust the escutcheon and nut to fasten the Thermostatic valve body with panel and wall.
Connect spout water inlet connector with Thermostatic valve’s water outlet connector as below:
Inspect hot and cool water tube, please clean it at first if necessary.
Connect your house hot water supply tube and cool water supply tube with Thermostatic valve body’s hot water inlet connector and cold water inlet connector separately.
Clean the faucets and showers as and when required. Regular cleaning can prevent calcification.
Never use cleaning materials contain hydrochloric, formic, phosphoric or acetic acid, which may cause considerable damage.
Never use cleaning materials or ap pliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads, or micro fiber cloths.
After cleaning, rinse thoroughly the faucet with clean water to remove any cleaner residue.
Unscrew and clean the aerator regularly.
A. Tighten the packing nut
Faucet leaks from the handle
B. Replace the "O" ring or packing pressure is too low
B. Clean or replace the aerator
C. Check plumbing system for water pressure problems
The spout sprays water all over
A. Clean or replace the aerator
B. Replace the aerator washer
Water is leaking A. Check the water supply connections to the faucet from the faucet B. Inspect the water supply lines or hoses for leaks under the sink
Handle is loose
A. Remove the cap and tighten the screw
B. Locate and tighten the hex set screw
C. Remove the handle and check for stripped teeth on the stem.
B. Clean the strainer of hot and cold water inlet illuminate
HONGKONG SUMERAIN SANITARY INDUSTRY CO..LIMITED
Address: ROOM 1018, HOLLYWOOD PLAZA 610 NATHAN ROAD MONGKOK, KL
Factory Address: Shuikou Industrial Park, Kaiping City, Guangdong Province,
Toll Free: 400-0999-075 (China mainland)
SUMERAIN INTERNATIONAL GROUP – AMERICA Branch
Address: 13455 Harper Dr.
Saratoga, CA 95070
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project