Allsource 41700 28 Gal. Abrasive Blaster With Vacuum Instruction manual

 SOURCE,
BLASTERS & EQUIPMENT
2BGALLON ABRAISIVE BLASTER WITH VACUUM
| ПЕММО.:41700
INSTRUCTION MANUAL
Allsource a division of S&H Industries Inc.
5200 Richmond Road Cleveland, Ohio 44146
- WWW.Shidustries.com Phone: 1-800-253-972
READ ALL INSTRUCTIONS
BEFORE OPERATING
SAVE THESE INSTRUCTIONS
Thank you for purchasing your Allsource Abrasive Blaster
with Vacuum. Before attempting to operate your new
Abrasive Blaster please read these instructions thoroughly.
You will need these instructions for the safety warnings,
precautions, assembly , operation, maintenance
procedures, parts list and diagrams. Keep your invoice
with these instructions. Write the invoice number on the
inside of front cover Keep the instructions and invoice
in a safe, dry place for future reference.
WARNING: The warnings, cautions and instructions
discussed in this instruction manual cannot cover all
possible conditions or situations that could occur. It must
be understood by the operator that common sense and
caution are factors which cannot be buitt into this product,
but must be supplied by the operator.
Silicosis and other Dust Warnings: Breathing dust from silica sand may cause
silicosis, a fatal lung disease. Breathing dust during blasting operations may
also cause asbestosis and/ or other serious or fatal diseases. A
NIOSH-approved, well maintained air supplied abrasive blasting respirator
must be used by anyone blasting, anyone handling or using media containing
toxic substances or media with more than one percent free crystalline
silica and anyone irr the area of the dust. Harmful dust can remain suspended
in the air for a long periods of time after blasting has ceased, causing serious
injury or death. |
Before removing respirator, use an air monitoring instrument to determine if
atmosphere is safe to breathe. Contact local OHSA or NIOSH office to
determine ifthe proper respirator for your particular application.
Air supplied respirators do not remove or protect against carbon monoxide (СО)
or any other toxic gas. Use a carbon monoxide removal device. and monitoring
device with the respirator to ensure grade D quality air. Follow all applicable
OSHA standards and OSHA regulation 1910.134 (d).
Disclaimer of Warranties. Manufacture, distributor and Allsource makes no
warranties with respect to any goods delivered to buyer or users except as
specifically set forth within this manual. Alisource makes no implied warranties
of merchantability or fitness for a particular purpose with respect to any of the
goods, and seller expressly disclaims any implied warranties against
infringement. Allsource warranties shall not apply to any damage or
non-conformity resulting from the negligent of improper assembly or use of
any goods by users or buyer or its employees or agents, or from alteration or
attempted repair by any person other than the manufacturer. All
used, repaired,modified or altered items are purchased as-is and with all fautts.
Limited Warranty
Allsource warrants this product to be free from defects in materials or
workmanship for one year after the date of original purchase. This warranty
does not include damage resulting from accident, abuse or misuse of the
product. Nor does it apply to parts subject to wear,l.e, nozzles,valves,hose
connections,and hoses. implied warranties including those of merchantability
and fitness for a particular purpose are excluded to the extent permitted by law,
and any and all implied warranties are excluded. Reimbursement of original
purchase price is the exclusive remedy and liability for consequential damages
under any and all warranties which are also excluded to the extent exclusion is
permitted by law,
SPECIFICATIONS -
Vacuum............................. 1100W(110V)
Blaster... eas 15 CFMOSOPSI
Weight... ненннноа 88 165
SAFETY RULES
1. Know your machine. Read this manual carefully. Learn
the machine's applications and limitations, as well
as specific potential hazards peculiar to it.
2. Ground all machines. If the machine is equipped with
three-pin plug, it should be plugged into a three-pin
electrical socket. Never remove the ground pin.
3. Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is
an increased risk of electric shock if your body is
grounded.
4. Do not expose tool to moisture. Don't use this machinery
in damp or wet locations. Keep out of rain.
5. Do not abuse cord. Never use the cord to carry tools.
or pull the plug from an outlet. Keep cord away from
heat, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords
incréase the risk of electric shock.
6. Remove adjusting keys or wrenches before turning the
tool on. A wrench or key that is left attached to a
moving part of the tool may result in personal injury.
7. Keep work area clean and well lit. Cluttered or dark
work areas invite accidents.
8. Keep children away. All children should be kept away
from the work area. Never let a child handle a tool
without strict adult supervision.
9. Do not operate this tool if under the influence of
alcohol or drugs. Read warning lables on
prescirptions to determine if your judgment or
reflexes are impaired while taking drugs. If there is
any doubt, do not attempt to operate.
10.Use safety equipment. Eye protection should be worn
at alltimes when operating this machine. Use ANSI
approved safety glasses. Everyday eyeglasses only
have impact resistant lenses. They are NOT safety
glasses. Niosh approved breathing apparatus, nonskid
safety shoes, hard hat, gloves or hearing protection
should be used in appropriate conditions.
11. Wear proper apparel. Loose clothing, gloves, neckties,
rings, bracelets, or other jewelry may present a
potential hazard when operating this machine.
Please keep all apparel clear of the machine.
12. Don't overreach. Keep proper footing and balance
at all times when operating this product.
13. Always disconnect the machine before making any
adjustments, storing, servicing, or changing
accessories. Such preventative safety measures
reduce the risk of starting the tool accidentally.
14. Use clamps or other practical means to secure and
support the work piece to a stable platform.
Holding the work by hand or against your body
may lead to a loss of control
15. Do not force tool. Use the correct tool for your
apolication. The correct tool will do the job better
and safer at the rate for which it was designed.
16. Do not use the tool if the switch does not turn it on
and off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
17. Check for damage. Check your tool regularly. If part of
the tool is damaged it should be carefully inspected
to make sure that it can perform it's intended
function correctly. If in doubt, the part should be
repaired. Refer all servicing to a qualified
technician. Consult your dealer for advice.
18. Keep away from flammables. Do not attempt to operate
this tool near flammable materials or combustibles.
Failure to comply may cause serious injury or
death.
19. Store idle tools out of the reach of children and
untrained persons. Tools may be dangerous in the
hands of untrained users.
ASSEMBLY INSTRUCTIONS
WARNING: Before operating read technical data
and instructions for use.
1, Open carton and remove the following contents:
1 plastic bag containing Instruction Manual.
1 plastic bag containing Brush Head Assemblies.
1 plastic bag containing Wheels, Castors and a
smaller Hardware Bag.
1 Wheel Axle |
1 Handle
Lay carton on its side to take the unit out.
. Remove all packing materials from abrasive blaster
Release the two snap locks on the vacuum
assembly and remove the vacuum head to take
the Vacuum Hose and Abrasive Hose out.
‘4, Install the castors and the wheels on the frame base.
Install the handle on the tank.
Fill 20-35 Ibs. of abrasive into the bottom container.
Reattach the vacuum head to the tank, making
certain both snap locks are securely locked
down. |
7. Insert the end of Vacuum Hose with Coupler into
the tank, and screw the other end without
coupler in the coupler on the brush head
assembly. Install one end of the Abrasive Hose
with a hose clamp on the end of the male air
connector. Install the other end of Abrasive Hose
with a hose clamp on the abrasive outlet
manifold.
N
99
Note: Ideal operating air pressure is 115 psi.
DO NOT exceed 140 psi.
You are now ready to begin work with your Abrasive
Blast/Vacuum.
OPERATING INSTRUCTIONS
1. If protective head gear and respiration is not already
in place, putit on now.
2. Set air compressor to 115 psi. (More or less,
depending on the surface to be cleaned.)
3. Connect air hose coupling to air coupling connector
located on gun handle.
Co A
. Connect power cord to power source.
. With gun pointed at surface to be cleaned, turn the
power switch on the vacuum head to the ON
position.
6. Have one hand holding the gun while the other hand
holds the brush handie.Note:Do not apply
pressure with the brush against the surface
being cleaned! The brush function is only intended
to prevent abrasive waste and to develop and
maintain a closed vacuum cycle for the abrasive to
be recycled. The brush is NOT intended to assist
in the abrasion process. |
7. Move both hands in the direction where rust removal
or pre-finish work is required.
8. By lenthening or shortening the nozzle with the set
nut, you will vary the size of the blast stream.
9. The bristle brush is for flat surfaces and also for
angles and corners. Before starting, spread out
\* the bristles in such a way that it does not cover the
jet spray inside the brush. (The abrasives will
eventually wear out the bristles). On car door
edges, we recommend that you wrap the bristles
- around the edge, which will generate better
vacuum, better coverage, safety, and results.
10. After each job, lift off vacuum head and knock dust
from the filter. After 1 hour of continuous
blasting, lift out the vacuum head and blow off
dust with direct air or vacuum.
11. When blasting a 90 degree corner, align the gun at
a 45 degree angle to reach the deepest area.
Move the gun in a slow, circular motion for best
results. | |
When finished with your Abrasive Blaster, unsnap the
two retaining clamps, empty dust container and store
the Abrasive Blaster in a safe, dry location.
TROUBLESHOOTING GUIDE
Symptom | Probable Cause Possible Solution
шо - Check air compressor and hose for leaks.
D 1. Possible |
ecrease in blast performance ) owalrpressure - Verify CFM input is compatible with
| blaster/vacuum
2. Moisture in the abrsive - Air must be clean and dry. Suggest airline
- filter. |
3. Dirty Filter
5. Gun Blockage
4. Abrasives are "worn" or too fine - Change abrasive
- Clean filter thoroughly
- Disconnect air and power, unscrew nozzle
and remove blockage with a paper clip or
thin wire.
Decrease in vacuum performance |. 1. Dirty Filter
2. Blocked or leaking vacuum line - Inspect all vacuum lines for blockage or
3. Insufficient air flow
- Clean filter thoroughly
damage, clean or replace as necessary.
- Check CFM input at airline connector point.
Abrasive is coming out between the | 1. Too much air pressure e .
bristles of the brush | 2. Blockage in the vacuum system | ° Inspect all vacuum lines for blockage or
- Check air pressure and adjust accordingly
damage, clean or replace as necessary.
Note: keep machine clean for optimum performance.
Selena nn
vacuum
ВТ I
п — :
Li
a > EHE
13 JA 31
| Mar
В A à
18
19 In
Lay!
N = 29
Л, 28
2/3 74 EN
connector
connector
nut
| caster
caster
nut
abrasive
12
12
vacuum motor
screw
screw
nut
+ nut
washer
nut
cover
6
rotational
e PEA
: 9 :
10 55 11
Г
AED A
Ly
a
\
anil
La
a
e
rt’
=
-—
=
py
-
La
ry
ww“
pg
pry
pg
pr
eg
=
и”
Z
Z
ry
и
EN
ED
24
21
E
Frl
PARTS
(ANA NAN NI
LIST
37
38
39
40
42
43
45
41
44