User`s Manual

User’s Manual

Ver. 1.02

IMPORTANT

• Read this manual thoroughly, and do not perform installation, operation, maintenance, or inspection unless you fully understand all of the contents.

• Keep this manual in a safe place where you can refer to it easily while installing, operating, and carrying out maintenance or inspections.

RS-61004-11 1.02

© ISHIDA Co., Ltd. 2008 All rights are reserved.

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means mechanical, electronic, photocopying, recording, or otherwise without prior written permission of ISHIDA.

ADJUSTMENT MODE

12.1 ADJUSTMENT MODE ENTRY

1.

Make sure that the initial screen is displayed.

Chapter 12 ADJUSTMENT MODE

12

2.

Press the [MODE] key on the key sheet.

The Operation Mode screen appears. Then, press the [ADJUST] button on the screen

3.

The Adjustment Menu Select screen appears.

UNI-5 User’s Manual 12-

1


12.2 DATE / TIME ADJUSTMENT

1.

Press the “TIME / DATE SET” field on the Adjustment Menu Select screen.

2.

The Time/Date Set screen appears.

3.

To change the date, enter a new date and press the “DATE” field.

EXAMPLE

22 June, 2007

12-2 UNI-5 User’s Manual


4.

To change the time, enter a new time and press the “TIME” field.

EXAMPLE

13:50:00

5.

To register new date and time, press the [SET] button.

6.

The confirmation screen appears. Then, press the [EXEC] button for execution.


3


12.3 TOUCH PANEL ADJUSTMENT

1.

Press the “TOUCH PANEL” field on the Adjustment Menu Select screen.

2.

The Touch Panel screen appears.

3.

Press the [+] button on the upper left of the screen.

4.

Press the [+] button on the lower right of the screen.


5.

Press the [SET] button to confirm calibration.



5


12.4 DISPLAY CHECK

1.

Press the “DISPLAY CHECK” field on the Adjustment Menu Select screen.

2.

The Display Check (Vertical) screen appears.

Press the [-] or [+] button to adjust vertical brightnesses for the operator and customer displays.

12-6

3.

Press the [HORIZONTAL] button to change to the horizontal display check screen.

4.

The Display Check (Horizontal) screen appears.

Press the [-] or [+] button to adjust vertical brightnesses for the operator and customer displays.

UNI-5 User’s Manual

Chapter 1 BEFORE USE

1

BEFORE USE

1.1 SPECIFICATIONS

Items Descriptions

Use conditions

Temperature: 5 to 35°C

Humidity: 30 to 85%, Non condensing.

Power supply: AC100 – 240V, 50 / 60Hz

Power consumption

Weight

Weighing capacity

Weighting accuracy

Operator/Customer display

Printing method

Thermal head

Printing speed

Printing effective size

Label size

Number of label cassettes

Input/Output

Program store medium

1.0A/0.5A

Bench type: Approx.11.5 kg

Pole type: Approx.12.5 kg

15 kg: 0 to 6/0.002 kg, 6 to 15/0.005 kg

1/3000

7.0 inch color, monochrome liquid crystal with back light, 480 X

234dots

Direct thermal method

2 inches (448dots) and 8 dots/mm

100mm/second, 120mm/second

Note: The printing speed may vary according to label conditions.

56mm

Label width: 30mm to 60mm

Label length: 20mm to 150mm

7 cassettes

LAN 1 channel

USB 1 channel

CF 1 channel

Drawer 2 channels

Flash ROM (32M bytes)

UNI-5 User’s Manual 1-1


1.2 MODEL VARIATIONS

Bench Type

Pole Type

Self-service Type

Elevated Type


1.3 PART NAMES AND FUNCTIONS

1.3.1 FRONT VIEW (BENCH TYPE)


1.3.2 REAR VIEW (BENCH TYPE)



1.4 OPERATION PANEL

Keys for Usual Use

Used to delete an entered numerical value.

Used to call a registered product data.

Used to feed labels.

Used to issue a label.

Used to enter tare weight.

Used to reset a weigh to zero.

1-4

Used to display Menu Select screen.

Used to turn the previous page.

Used to turn the next page.

Used to jump to the top page.

Used to jump to the end page.

Used to escape from the current mode.



1.5 ADJUSTMENTS

Install the machine horizontally to use.

Be sure to turn off the power switch before placing the machine on a stable platform, and adjust the machine inclination by turning the four level adjustment feet so that the bubble is located at the center of the level gauge. Accurate measurements cannot be performed if it is not installed horizontally.

1.5.2 OPERATION PANEL ANGLE ADJUSTMENT (BENCH TYPE)

To obtain a better view, adjust the angle of the operation panel within the range between 0 and 70 degrees.



1.6 LABEL / RECEIPT ROLL LOADING

1.

Open the cover on the side of main body.

2.

Set a new roll around the roll holder and raise the roll stopper to fix the roll position.

3.

Thread the paper as shown in the figures below..



4

For labels, fix the paper end with the backing paper stopper, and gently turn the winding bobbin counterclockwise until the label becomes tight.

5.

Slide the label/receipt guide to help smooth paper feeding according to the paper width.



6.

For labels, press the [FEED] key on the key sheet to issue a label.

At this time, confirm that the label is completely peeled off.

Confirm that the backing paper is wound up smoothly. If the backing paper is wound up diagonally, check that the label is set correctly.



1.7 REMOVING & REPLACING OF WEIGH PLATTER

1.7.1 REMOVING THE WEIGH PLATTER

When removing the weigh platter from the main body, lift the front side to pull out the two pins from the two rubber platter holders and remove the platter by pulling it to disengage the two hooks at the rear side of the platter.

1.7.2 REPLACING THE WEIGH PLATTER

When replacing the weigh platter onto the main body, engage the two hooks at the rear side of the platter and lower the platter so that the two pins on the bottom of the platter are inserted into holes of the rubber platter holders.



1.8.4 PRECAUTIONS WHEN USING CLEANING FLUIDS

Use a soft cloth and a neutral detergent to clean the machine.

Do not use thinner, benzene, etc. Doing so may damage the original safety functions.

For some parts, use cleaning fluid (isopropyl alcohol).

Do not use cleaning fluid near fire as the fluid is flammable.

Do not use cleaning fluid in a poorly ventilated area. Always provide adequate ventilation when cleaning.

Take the following actions in the event of an accident:

If the fluid gets in your eye

Immediately wash your eye(s) with water for at least 15 minutes, and consult your doctor.

If you wear contact lenses, remove and wash them.

If the fluid comes into contact with your skin

Immediately rinse the area of contact with water, and then wash with soap.

If you notice any skin abnormalities at the area of contact, or if any pain persists, consult your doctor.

If the fumes of the fluid are inhaled

Immediately move the victim to an area where fresh air is available, and have the victim lie down and keep warm.

If breathing becomes difficult or stops, provide artificial respiration and seek medical attention immediately.

If the fluid is swallowed

Do not try to induce vomiting.

Do not give the victim anything to drink, and do not rinse the mouth.

If vomiting occurs naturally, have the victim lean forward to reduce risk of aspiration.

Keep the victim warm and seek medical attention.



1.9 STARTING PROCEDURES

1.9.1 TURNING ON THE POWER

1.

Push down the "I” side of the Power Switch to turn on the power.

2.

The Time Check screen appears.

Then, check that displayed date and time agree with current date and time, and press the

[ENTER] button on the screen to proceed to the next step.

Note: Refer to “Time/Date Set” menu in Adjust Mode when changing the date or time.

21-JUN-2007

11:13:38

3.

After a while, the initial screen appears.



1.9.2 PERFORMING ZERO ADJUSTMENT

1.

If the weight value is not zero on the initial screen,

Press the [ZERO] key on the key sheet to perform zero weight adjustment.

2.

The “ZERO” indicator lights up and the weight value becomes zero.



1.9.3 GETTING BACK TO THE INITIAL SCREEN

1.

To get back to the initial screen from a Menu Select screen, press either the “SALES” field or the icon at the bottom right on the screen.

2.

The initial screen appears.


Chapter 2 LABEL ISSUE

LABEL ISSUE

2.1 LABEL ISSUE WITHOUT OPERATOR

2.1.1 WEIGHING UNIT PRICE PRODUCTS

1.

Ensure that the initial screen is displayed.

2

2.

Enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet, or simply press a preset key on the screen where the product is allocated.

EXAMPLE

PLU No.6 “Roast Beef”

Î

or

3.

When the product is preset as a traceable item, the traceability screen appears.

See Chapter 4 for more details about traceability products.

4.

The selected PLU screen appears.

Without Preset Tare Weight


1


With Preset Tare Weight

Manual Tare Entry

To newly enter a tare weight or overwrite an existing tare weight, enter the tare weight using the numeric keys and press the “TARE” field on the screen.

EXAMPLE

Tare weight “50g”

5.

See Chapter 5 for more details about temporary change operations.

6.

Put a product on the weigh platter.

The weight is measured and the total price is calculated.


7.

When “MANUAL” is set in the Print Mode,


Press the [PRINT] key on the key sheet.

The label is issued.

Non-traceable products Traceable products

When “AUTO” is set in the Print Mode,

The label is automatically issued as soon as the weighing is stabilized.



3


2.1.2 WEIGHING FIXED PRICE PRODUCTS

1.


2.


EXAMPLE


Î

or

2-4

3.



4.








EXAMPLE


5.


6.


The weight is measured but the fixed price stays same.


5


7.

When “MANUAL” is set in the Print Mode,



When “AUTO” is set in the Print Mode,

2-6

The label is automatically issued as soon as the weighing is stabilized.



1.



2.


EXAMPLE


Î

or

3.



4.


5.



7


6.

Press the [PRINT] key on the key sheet to issue the labels.



Remove the label.

The next label is issued.


Note: To stop printing, press the [PRINT] key again.


1.



2.


EXAMPLE


Î

or

3.



4.


5.



9


6.

Enter the fixed weight using the numeric keys on the key sheet and press the “FIXED

WEIGHT” field.

EXAMPLE

Fixed weight “858g”

7.

Press the [PRINT] key on the key sheet to issue the labels.



Remove the label.

The next label is issued.

2-10


Note: To stop printing, press the [PRINT] key again.


2.2 LABEL ISSUE WITH OPERATORS

2.2.1 WEIGHING UNIT PRICE PRODUCTS

1.



2.


EXAMPLE


Î

or

3.

4.



The selected product screen appears.




11




EXAMPLE


5.


6.




7.

Press a operator button on the screen to issue the label.

EXAMPLE

Operator “BETTY”




13


2.2.2 WEIGHING FIXED PRICE PRODUCTS

1.


2.


EXAMPLE


Î

or

3.

4.










EXAMPLE


5.


6.




15


7.


EXAMPLE




1.



2.


EXAMPLE


Î

or

3.



4.


5.



17


6.


EXAMPLE




1.



2.


EXAMPLE


Î

or

3.



4.


5.



19


6.

Enter the fixed weight using the numeric keys on the key sheet and press the “FIXED

WEIGHT” field.

EXAMPLE

Fixed weight “858g”

7.


EXAMPLE




Chapter 3 RECEIPT ISSUE

RECEIPT ISSUE

3.1 SALES BY THE SAME OPRATOR

1.


3

2-1

Select a desired product category by pressing the corresponding field on the screen.

EXAMPLE

Select “Meat” category.

2-2

The PLU preset screen for the selected category appears.

Then, enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet, or simply press a preset key on the screen where a desired product is allocated.

EXAMPLE

Select PLU No.1 “Rib Steak”.

Î

or


1


2-3

The PLU screen appears.

Weighing Unit Price PLU

2-4


2-5

Press a button on the screen for the operator who has sold the product.

EXAMPLE

Select “Operator 002”.



2-6

The subtotal for the selected operator is shown on the screen.

3-1


EXAMPLE

Select “Fish” category.

3-2



EXAMPLE

Select PLU No.102 “Maine Lobster”.

Î

or


3


3-3


Fixed Price PLU

3-4


EXAMPLE


3-5


4-1


EXAMPLE

Select “Bakery” category.



4-2



EXAMPLE

Select PLU No.201 “Live Wild Cherry Clam”.

Î

or

4-3


Weighing Fixed Price PLU

4-4



5


4-5


EXAMPLE


4-6


5-1


EXAMPLE


5-2




EXAMPLE

Select PLU No.4 “Pork Chops”.

Î

or


5-3


Fixed Unit Price PLU

5-4

Enter the weight using the numeric keys on the key sheet, and press the “Fixed Weight” field on the screen.

EXAMPLE

Weight “400g”


7


5-5


EXAMPLE


5-6


6.

Press the subtotal field on the screen to display more detailed subtotal data.

7.

The detailed subtotal screen appears for confirmation of product registrations.

Then, confirm that the detail of the transaction is correct.



8.

Press the [PRINT] key on the key sheet to issue the receipt.


9


9.

The Subtotal screen appears for the settlement.



3.2 SALES BY DIFFERENT OPRATORS

1.


2-1

EXAMPLE

Product registration by “Operator 002”


EXAMPLE


2-2



EXAMPLE

Select PLU No.1 “Rib Steak”.

Î

or


11


2-3



2-4


2-5


EXAMPLE




2-6


3-1

EXAMPLE



EXAMPLE

Select “Fish” category.

3-2



EXAMPLE

Select PLU No.102 “Maine Lobster”.

Î

or


13


3-3


Fixed Price PLU

3-4


EXAMPLE


3-5


4-1

EXAMPLE



EXAMPLE

Select “Bakery” category.



4-2



EXAMPLE

Select PLU No.201 “Live Wild Cherry Clam”.

Î

or

4-3


Weighing Fixed Price PLU

4-4



15


4-5


EXAMPLE


4-6


5-1

EXAMPLE



EXAMPLE




5-2



EXAMPLE

Select PLU No.4 “Pork Chops”.

Î

or

5-3


Fixed Unit Price PLU

5-4

Enter the weight using the numeric keys on the key sheet, and press the “Fixed Weight” field on the screen.

EXAMPLE

Weight “400g”


17


5-5


EXAMPLE


5-6


6.


7.

The detailed subtotal screen appears for confirmation of product registrations.

Then, confirm that the detail of the transaction is correct.



8.


9.



19


10-1

EXAMPLE



EXAMPLE


10-2



EXAMPLE

Select PLU No.3 “Round Steak”.

Î

or

10-3




10-4



10-5


EXAMPLE


10-6



21


11

EXAMPLE

Receipt issue by “Operator 001”


12

The Subtotal screen appears for confirmation of product registrations.

13




14



23


3.3 VOIDING PRODUCT REGISTRATION

1.

To void a product registration that has been made in the transaction, display the Subtotal screen for confirmation of product registrations.

2.

Press to select a desired product registration field.

EXAMPLE

Void the third item.

Note: To scroll the selection up or down, press the [

c

] or [

d

] keys on the key sheet.

3.

Press the [VOID] button on the screen.

4.

The confirmation screen appears. Then, press the [EXEC] button for execution.


5.

The selected item has been voided.

6.



Deleted by a dashed line


25


7.



Chapter 4 TRACEABILITY PRODUCTS

4

TRACEABILITY PRODUCTS

4.1 REFERING TO PREVIOUS TRACEABILITY DATA

1.


2.


EXAMPLE

PLU number “6”.

Î

or

3.

When the product is preset as a traceable item, the Traceability screen appears.


1


4.

To refer to the previously processed traceability data, press the [LIST] button.

5.

The Traceability History screen appears. Then, press to select a desired data field.

6.

The selected data appears. Then, press the [SET] button.

7.


Weighing Unit Price Products


Fixed Price Products


Fixed Unit Price Products

Weighing Fixed Price Products


3


4.2 CHANGING TRACEABILITY DATA

1.


2.


EXAMPLE

PLU number “6”.

Î

or

4-4

3-1

When the product is preset as a traceable item, the Traceability screen appears.

Then, confirm whether information on the screen is correct or not.

When the data is correct, press the [SET] button.



3-2

If the data is not correct, press to select a desired data field.

EXAMPLE Select “France”.

EXAMPLE Change to “Argentina”.

The data has been changed.

To change the “FACTORY” data, press the corresponding field.

Press to select a desired data field.


5


The data has been changed. Then, press the [SET] button.

4.

When changing the lot data, press the “LOT” filed.

The Traceability Lot Number Set screen appears.

4-6

Change the lot number using the [ABC] [ERASE] and [BACK SPACE] buttons, and press the [BACK] button to finish.



The confirmation screen appears. Then, press the [SAVE] button to save the data.

The Traceability screen appears. Then, press the [SET] button.

5.





7





Chapter 5 TEMPORARY CHANGE OPERATIONS

TEMPORARY CHANGE OPERATIONS

5.1 UNIT PRICE CHANGE

1.

Ensure that the selected PLU screen is displayed.

Weighing Products

5


2.

Enter a desired unit price using the numeric keys and press the “UNIT PRICE” or “FIXED

UNIT PRICE” field.

EXAMPLE

“$3.80”

.

Weighing Products


1





1.




2.

Enter a desired price using the numeric keys, and press the “FIXED PRICE” field.

EXAMPLE

“$3.80”

.



3





5.3 AMOUNT DISCOUNT FOR UNIT PRICE

1.




2.

Enter a desired discount amount using the numeric keys, and press the “-$ (U/P)” field.

EXAMPLE

Discount amount “$1.00”.



5





5.4 PERCENT DISCOUNT FOR UNIT PRICE

1.




2.

Enter a desired discount percentage using the numeric keys on the key sheet, and press the “-% (U/P)” field.

EXAMPLE

Discount percentage “10%”.


7





5.5 AMOUNT DISCOUNT FOR TOTAL PRICE

1.




2.

Enter a desired discount amount using the numeric keys, and press the “-$” field.

EXAMPLE

Discount amount “$1.00”.



9





5.6 PERCENT DISCOUNT FOR TOTAL PRICE

1.




2.

Enter a desired discount percentage using the numeric keys on the key sheet, and press the “-%” field.

EXAMPLE

Discount percentage “10%”.


11





5.7 PRODUCT QUANTITY CHANGE

1.



2.

Enter a desired quantity using the numeric keys, and press the “PCS” field.

EXAMPLE

Quantity “2 pieces”

.

3.

To select a desired fix price mark, press the “PCS” field again.


13


4.

The Fix Price mark List screen appears. Then, select a desired mark by pressing the corresponding field.

EXAMPLE

Price mark “PC. PCS.”



1.

Ensure that the selected PLU screen is displayed and “AUTO” is selected in the Printing

Mode.


2.

Enter a desired number of labels and press the “PRN QTY (Print Quantity)” field on the screen.

EXAMPLE

Print quantity “3”.

3.


The set number of labels will be issued.

Note: To interrupt the issue of labels, press the [PRINT] key again.

To continue the issue of labels, press the [PRINT] key again.


15

Chapter 6 SELF-SERVICE OPERATIONS

SELF-SERVICE OPERATIONS

6.1 WEIGHING PRODUCTS

1.


6

2.

Select a desired product by pressing the corresponding button on the screen.

EXAMPLE

Select “Roast Beef”

3.



1


4.



5.

Press the [LABEL PRINT] button on the screen to issue the label.




6.2 FIXED PRICE PRODUCTS

1.


2.

Select a desired product by pressing the corresponding button on the screen.

EXAMPLE


3.


Then, press the [LABEL PRINT] button on the screen to issue the label.



6-

3

Chapter 7 ACCUMULATOR MODE

ACCUMULATOR MODE

7.1 MANUAL INPUT ACCUMULATION

1.

To get the Operation Menu Select screen, press the [MODE] key on the key sheet.

7

Then, press the “ACC (Accumulator)” filed.

2.

The Accumulator (Input Number Accumulation) screen appears.

3.

Enter a desired PLU number and press the [PLU] key on the key sheet.

EXAMPLE

PLU number “6”.

Î

The Input Number Accumulation screen for the selected product appears.


1


4.

Enter a quantity, weight, and price that are to be accumulated and press the corresponding fields for registration. Then, press the [ACC] button on the screen.

EXAMPLE

Quantity “1 pc.”, Weight “169g”, Price “$0.84”

5.

The confirmation screen appears. Then, press the [EXEC] button on the screen.

6.

The registration has been completed.



7.2 WEIGHING ACCUMULATION

1.



2.

To get the Weighing Accumulation screen, press the [WGT. ACC] tab.


3


3.


EXAMPLE

PLU number “6”.

Î

The Weighing Accumulation screen for the selected product appears.

4.

Put a product on the weigh platter and press the [ACC] button on the screen..

7-4

5.



6.

Remove the product from the weigh platter.



5


7.3 MANUAL INPUT VOID

1.



2.

To get the Input Number Void screen, press the [NUM. VOID] tab.



3.


EXAMPLE

PLU number “6”.

Î

The Input Number Void screen for the selected product appears.

4.

Enter a quantity, weight, and price that are to be voided and press the corresponding fields for registration. Then, press the [VOID] button on the screen.

EXAMPLE


5.



7


6.




7.4 WEIGHING VOID

1.



2.

To get the Weighing Void screen, press the [WGT. VOID] tab.


9


3.


EXAMPLE

PLU number “6”.

Î

The Weighing Void screen for the selected product appears.

4.

Put a product on the weigh platter and press the [VOID] button on the screen..

5.



6.




11

Chapter 8 TOTAL ADJUST MODE

TOTAL ADJUST MODE

8.1 MANUAL INPUT SUBTRACTION

1.

To get the


8

Then, press the “TOTAL ADJUST” filed.

2.


EXAMPLE

PLU number “6”.

Î

The Total Adjust (Input Number Subtraction) screen for the selected product appears.


1


3.

Enter a quantity, weight, and price that are to be subtracted and press the corresponding fields for registration. Then, press the [SUB] button on the screen.

EXAMPLE


4.


5.




8.2 WEIGHING SUBTRACTION

1.



2.

To get the Total Adjust (Weighing Subtraction) screen, press the [WGT. SUB] tab.


3


3.


EXAMPLE

PLU number “6”.

Î

The Total Adjust (Weighing Subtraction) screen for the selected product appears.

4.

Put a product on the weigh platter and press the [SUB] button on the screen..

8-4

5.



6.




5


8.3 MANUAL INPUT ADDITION

1.



2.

To get the Total Adjust (Input Number Addition) screen, press the [NUM. ADD] tab.



3.


EXAMPLE

PLU number “6”.

Î

The Total Adjust (Input Number Addition) screen for the selected product appears.

4.

Enter a quantity, weight, and price that are to beaded and press the corresponding fields for registration. Then, press the [ADD] button on the screen.

EXAMPLE


5.



7


6.




8.4 WEIGHING ADDITION

1.



2.

To get the Total Adjust (Weighing Add) screen, press the [WGT. ADD] tab.


9


3.


EXAMPLE

PLU number “6”.

Î

The Total Adjust (Weighing Add) screen for the selected product appears.

4.

Put a product on the weigh platter and press the [ADD] button on the screen..

8-10

5.



6.




11

TOTAL MODE

9.1 DAILY TOTAL

1.

Press the “PRODUCTION DAILY TOTAL” filed.

Chapter 9 TOTAL MODE

9

2.

The Daily Total screen appears.

3.

To obtain the Hourly Total screen, press the [HOUR.] tab.

To change the pages, press the [ b

] or [ a ] button on the screen.


1


4.

To obtain the Department Total screen, press the [DEPT.] tab.


] or [ a

] button on the screen.

5.

To obtain the Group Total screen, press the [GROUP] tab.


] or [ a


6.

To obtain the Designated Item Total screen, press the [ITEM] tab.

9-2

Enter a desired PLU number using the numeric keys and press the [PLU] key on the key sheet.



EXAMPLE

PLU number “6”.

Î

7.

To obtain the Operator Total screen, press the [ORER.] tab.

8.

To obtain the Class Total screen, press the [CLASS] tab.

NO

DEPT.

The object of analysis is not specified.

The object of analysis is specified to be departments.

GROUP

PLU No.

The object of analysis is specified to be groups.

Analysis is performed in ascending PLU number order.

ABC PRICE Analysis is performed in descending price order.

ABC WEIGHT Analysis is performed in descending weight order.

ABC PCS

Z PRICE

Z WEIGHT

Z PCS

Analysis is performed in descending quantity order.

Analysis is performed in ascending price order.

Analysis is performed in ascending weight order.

Analysis is performed in ascending quantity order.


3


9.2 WEEKLY TOTAL

1.

Press the “PRODUCTION WEEKLY TOTAL” filed.

2.

The Weekly Total screen appears.


] or [ a


3.

To obtain total for the day-of-the week, press a desired day-of-the week tab.


] or [ a





5


9.3 CUMULATIVE TOTAL

1.

Press the “PRODUCTION CUMULATIVE TOTAL” filed.

2.

The Cumulative Total screen appears.

9-6

3.

To obtain total for each department, press the [DEPT.] tab on the screen.


] or [ a


4.

To obtain total for each group, press the [GROUP] tab on the screen.


] or [ a




5.

To obtain total for each operator, press the [OPER.] tab on the screen.



6.

To obtain analysis totals, press the [CLASS] tab on the screen.


] or [ a


NO

DEPT.

The object of analysis is not specified.

The object of analysis is specified to be departments.

GROUP

PLU No.

The object of analysis is specified to be groups.

Analysis is performed in ascending PLU number order.

ABC PRICE Analysis is performed in descending price order.

ABC WEIGHT Analysis is performed in descending weight order.

ABC PCS

Z PRICE

Z WEIGHT

Z PCS

Analysis is performed in descending quantity order.

Analysis is performed in ascending price order.

Analysis is performed in ascending weight order.

Analysis is performed in ascending quantity order.


7


9.4 TRACEABILITY TOTAL

1.

Press the “TRACEABILITY TOTAL” filed.

2.

The Traceability Item screen appears.


] or [ a


To obtain Traceability Total screen, press the [DETAIL] button on the screen.

3.

The Traceability Total screen appears.


9.5 PRESET REPORT PRINTING

1.

Press the “PRESET REPORT” filed.


2.

The Preset Report screen appears.

3.

Select desired reports by pressing the corresponding fields.

Press the [STRAT] button to issue selected join reports.


9


9.6 TOTAL CLEAR

1.

Press the [ b


2.

The second page of the Menu Select screen appears.

To obtain the Total Clear screen, press the “TOTAL CLEAR” field on the screen.

9-10

3.

The Total Clear screen appears.

4.

Select desired reports to be cleared by pressing the corresponding fields.



5.

Press the [EXEC] button.

6.

The confirmation screen appears. Then, press the [EXEC] button on the screen for execution.


11

PROGRAM MODE

10.1 PROGRAM MODE ENTRY

1.


Chapter 10 PROGRAM MODE

10

2.


The Operation Menu Select screen appears.

Then, press the [PROGRAM] button on the screen.

3.

The Program Menu Select screen appears.


] or [ a



10-1


10-2



Note: To exit the Program Mode, press the [ESC] (Escape) key on the key sheet.


10-3


10.2 PLU FILE REGISTRATION

1.

Press the “PLU FILE” field on the Program Menu Select screen.

2.

The Item List screen appears.


] or [ a

] button on the screen

3.

Press to select a desired field. Then, press the [DETAIL] button on the screen.

EXAMPLE

Select “Roast Beef”.

4.

The Item Detail screen appears.

To edit the PLU name, press the [EDIT] button on the screen.

10-4



5.

The text edit screen appears.

Edit a text according to the procedure explained in Appendix “Text Editing”.

6.

Ensure that the first sales related screen is displayed.

Sales Mode: Weighing Product

Sales Mode: Fixed Price Product

Sales Mode: Weighing Fixed Price Product


10-5


Sales Mode: Fixed Unit Price Product

ITEM DESCRIPTION

Press the [

<] or [>] button to select a desired sales mode.

SALES MODE

0: Weighing product

1: Fixed price product

2: Weighing fixed price product

3: Fixed unit price product

Press the [

<] or [>] button to select a desired markdown mode.

MARKDOWN

MODE

OPEN PRICE

0: Normal price

1: Special price

2: Amount discount for total price

3: Percent discount for total price

4: Special unit price

5: Amount discount for unit price

6: Percent discount for unit price

Press the [

<] or [>] button to select whether or not to allow an open price system.

UNIT PRICE

FIXED PRICE

Enter a unit price or fixed price, and press this field.

M/D AMOUNT

Enter a markdown amount or percentage and press this field.

QTY (Quantity)

Enter a packed quantity, and press this field.

Press this field to display the Fix Price Mark List screen.

UNIT TYPE

TAX

Press to select a desired field.

Enter a desired number and press this field.

FIXED WEIGHT Enter a fixed weight, and press this field.

TARE Enter a tare weight, and press this field.

UNDER WEIGHT Enter a lower weight limit, and press this field.

UPPER WEIGHT Enter a upper weight limit, and press this field.

10-6



7.

Press the [SALE2] tab to select the second sales related screen.

8-1

ITEM DESCRIPTION

POINT

Press the [

<] or [>] button to select whether or not to use the Point Flag.

FLAG

0: OFF

POINT

1: ON

Press the [

<] or [>] button to select a desired Point Type.

TYPE

0: Weight

1: Fixed weight

POINTS Enter a desired number and press this field

Press the [MESSAGE] tab to select the message related screen.

8-2


EXAMPLE

“Extra Message 1”.


10-7


8-3

The Extra Message List screen appears. Then, press to select a desired field.

EXAMPLE

“Extra Message BB”.

9-1

Press the [IMAGE] tab to select the image related screen.

9-2


EXAMPLE

Select a desired image for “Image 1”.

10-8



9-3

The Image List screen appears. Then, press to select a desired field and press the [SET] button.

EXAMPLE

Select “Image No.8”.

10.

Select whether or not to print Safe handling Image by pressing a desired field.

11-1

Press the [PRINT] tab to select the print related screen.

11-2

Press the [First Label Format No.] button.


10-9


11-3

The Format List screen appears.

Then, select a desired format by pressing the corresponding field.

EXAMPLE

Select “Format No.5”.

ITEM DESCRIPTION

Press the [

<] or [>] button to select whether or not to print the

FIRST LABEL

PRINT first labels.

1: YES

SECOND LABEL

PRINT

2: NO

Press the [

<] or [>] button to select whether or not to print the second labels.

1: YES

2: NO

Note: The same procedure applies to the Second Label Format Number setting.

10-10


12.

Pressing the [DATE] tab to select the date related screen.


ITEM DESCRIPTION

PACK DATE

PRINT

Select whether or not to print the Pack Date.

Press the [

<] or [>] button to select a desired printing method.

PACK TIME PRINT

PACK TIME DATA

0: No print

1: Designated time

2: System clock time

This field is available only when “Designated time” is selected in

“PACK TIME PRINT”.

Enter the time and press this field.

SB DATE PRINT Select whether or not to print the Sell-By Date.

Press the [


SB TIME PRINT

SB TIME DATA

0: No print

1: Designated time

2: Relative time

This field is available only when “Yes” is selected in “SB TIME

PRINT”.

Enter the number of hours and press this field.

SHELF LIFE

(days)

UB DATE PRINT

UB DATE DATA

This field is available only when “Yes” is selected in “SB DATE

PRINT”.

Enter the number of days and press this field.

Select whether or not to print the Use-By Date.

This field is available only when “Yes” is selected in “UB DATE

PRINT”.

Enter the number of hours and press this field


10-11


13.

Select the code related screen by pressing the [CODE] tab.

ITEM DESCRIPTION

ITEM CODE Enter an item code and press this field.

REGISTER CODE Enter the register code and press this field.

POS FLAG

This field is available only when “PLU File” is selected in “POS

REFERENCE”. Enter the POS flag number and press this field.

BARCODE Enter the barcode number and press this field.

Select one of the following reference methods

POS REFERENCE

0: Refer

1: PLU file

This field is available only when “PLU File” is selected in “POS

REFERENCE”.

Press this field to get the Barcode Type screen and press to select one of the PLU types.

BARCODE TYPE

Press this field to get the Barcode Format screen and press to select one of the barcode formats.

10-12



TRACE ENABLE

Select whether or not to enable a traceability function.

Press this field to get the Department List screen.

Set the desired department simply by pressing the field on the

DEPARTMENT No. list, or pressing the “Department No.” field after a numeric entry.

GROUP No.

Pressing this field displays the Group List.

Set the desired group simply by pressing the field on the list, or pressing the “Group No.” field after a numeric entry.


10-13


10.3 CAMPAIGN LIST REGISTRATION

1.

Press the “CAMPAIGN” field on the Program Menu Select screen.

2.

The Campaign List appears.

To change the pages, press the [ b] or [a] button on the screen.

3.

Create a new campaign file by entering a campaign number and pressing the [PLU] key on the key sheet.

EXAMPLE

Campaign number “2”.

Î

The confirmation screen appears. Then, press the [ENTER] button.

10-14


4.

The designated Campaign Data List screen appears.


5.

Enter the campaign start date and press the “Start Date” display field. .

EXAMPLE

Start date "June 25, 2007”

6.

Enter the start time and press the “Start Time” display field. .

EXAMPLE

Start time "08:00”


10-15


7.

Enter the campaign end date and press the “End Date” display field. .

EXAMPLE

End date "June 27, 2007”

8.

Enter the end time and press the “End Time” display field.

EXAMPLE

End time "21:00”

10-16

9.

Press the [CALL] button to call up Item List screens



10.

The Item List screen appears. Then, press to select a desired item field.

EXAMPLE

PLU number “4”

11.

The Campaign Data List screen appears.

Then, press the [CALL] button again when selecting the next item.

The pop-up list appears. Then, press to select a desired field.

EXAMPLE

Percent discount “-%”


10-17


12.

Enter a numeric value and press the “Markdown Price” field for registration.

EXAMPLE

10%

13.

Repeat steps 9 through 12 for further registration.

Then, press the Return button to finalize this procedure.

The Campaign List screen appears.

10-18



10.4 OPERATOR REGISTRATION

1.

Press the "OPERATORS” field on the Program Menu Select screen.

2.

The Operator List screen appears.

3.

To create a new operator, enter the operator number and press the [PLU] key on the key sheet.

EXAMPLE

Operator number “7”.

Î

The confirmation screen appears. Press the [ENTER] button.


10-19


4.

The Operator Edit screen appears for the selected operator number.

Edit a text according to the procedures described in Appendix “Text Editing”.

5.

Press the [ESC] key on the key sheet to escape from text editing mode.

The confirmation screen appears.

Then, press the [SAVE] button to save the data.

10-20



6.

The edited text has been registered.

7.

Press the Return button to finalize this procedure.


10-21


10.5 PRESET KEY REGISTRATION

10.5.1 SETTING PRESET FUNCTIONS

1.

Press the “PRESET KEY” field on the screen.

2.

The Preset Key (Panel) screen appears.

3.

Ensure that the [SET] button is selected.

10-22



4.

Press a desired button to which a preset function will be assigned.

5.

Available functions are listed on the screens.

To change the pages, press the [ b] or [a] button on the screen.


10-23


6.

Press to select the desired function on the list, and press the [SET] button.

EXAMPLE

Select PLU function.

7.

The Item List screen appears. Then, press to select a desired field.

EXAMPLE

Select PLU No.2.

8.

The selected PLU has been assigned.

10-24



9.

Repeat steps 4 through 8 for more registrations.


10-25


10.5.2 ASSIGNING IMAGES ON THE PRESET KEYS

1.


2.


3.

Press the [IMAGE] button.

4.

Press a desired preset key where the function is already assigned.

EXAMPLE


10-26



5.

The Image List screen appears.

6.

Press to select a desired image.

EXAMPLE

Image No.3

7.

The image has been assigned.

8.



10-27


10.5.3 COLORING PRESET KEYS

1.


2.


3.

Press the [COLOR] button. Then, ensure that “Back Color” is selected.

4.

Press to select a desired preset key.

EXAMPLE


10-28



5.

The Preset Key (Color) screen appears. Then, press to select a desired color.

6.

Selected color has been given to the background of the key.

7.

Press the [BACK COLOR] button to change to the [FORE COLOR] button.

8.


EXAMPLE



10-29


9.

The Preset Key (Color) screen appears. Then, press to select a desired color.

10.

Selected color has been given to the foreground of the key.

11.


10-30


10.5.4 CHANGING PRESET KEY SIZES

1.



2.


3.

Press the [SIZE] button, and ensure that “SMALL” is selected.

Press the [SMALL] button to change to the [MIDDLE] button.


10-31


Press the [MIDDLE] button to change to the [LARGE] button.

4-1

Change the size of a desired key.

EXAMPLE

Change to the middle size of the “Roast Beef” key.

Ensure that the [MIDDLE] button is selected.

Press the “Roast Beef” key.

10-32



4-2

Change the size of a desired key.

EXAMPLE

Change to the large size of the “Roast Beef” key.

Ensure that the [LARGE] button is selected.

Press the “Roast Beef” key.

5.

Repeat steps 3 through 4-2 for more registrations.


10-33


10.5.5 EDITING PRESET KEY NAMES

1.


2.


3.

Press to select the [EDIT] button.

4.


EXAMPLE

Select the [Roast Beef] key.

10-34



5.

The text edit screen appears.

6.

Edit a desired text according to the procedures described in Appendix “Text Editing”.

EXAMPLE

“Beef Fillet”.

7.

To finalize the editing, press the [ESC] key on the key sheet.



10-35


8.


9.


10-36


10.5.6 CONFIRMING PRESET KEY DATA

1.



2.


3.

Press to select the [DATA] button.

4.

Press a desired preset key. The related data is displayed on the button.

EXAMPLE

“Beef Fillet” and the PLU No.6


10-37


10.5.7 DELETING PRESET KEYS

1.


2.

The Preset Key (Panel) screen appears. Ensure that the [SET] button is selected.

3.

Press a desired preset key to be deleted.

EXAMPLE

Delete the [Roast Beef] key”.

4.

The Function List screen appears, and the assigned function field is highlighted.

10-38


5.

Press to select the “NO” field, and press the [SET] button.


6.

The selected key has been deleted.

7.

Repeat steps 3 through 6 for more deletions.


10-39


1.


2.

The Preset Key (Panel) screen appears. Then, press the [MEMBRANE] tab.

3.

The Preset Key (Membrane) screen appears.

4.

Press to select a desired membrane key to which the preset data is assigned.

10-40



The selected key number and name are shown on the screen.

To assign a desired function to the selected key, press the Name field.

5.

The Function List screen appears.

6.

Select a desired function to be assigned by pressing the corresponding field, and press the [SET] button.

EXAMPLE

Select “PLU”

7.

The Item List screen appears. Then, press to select a desired field.

EXAMPLE

PLU No.5


10-41


8.

The selected PLU has been assigned to the selected membrane key.

10-42



10.6 ADVERTISEMENT MESSAGE REGISTRATION

1.

Press the “AD MSG (Advertisement Message)” field on the Program Menu Select screen.

2-1

The Advertisement Message List screen appears.

When creating the first message, press the [NEW] button.

2-2

When creating a message other than the first one, enter a desired message number using the numeric keys and press the [PLU] key on the key sheet.

XAMPLE

Message number “2”.

3.

Î

The confirmation screen appears.

Then, press the [ENTER] button.


10-43


4.

The Advertisement Message (Text) screen appears. Then, press the [EDIT] button.

The Advertisement Message Edit screen appears.

Edit a desired message according to the procedures described in Appendix “Text Editing”.

10-44





5.

The Advertisement Message (Text) screen for the designated message number appears.

ITEM DESCRIPTION

Press the [

<] or [>] button to select a desired display type.

TEXT DISPLAY

TYPE

0: None

1: Slide

2: Flash

Press the [

<] or [>] button to select a desired display type.

IMAGE DISPLAY

TYPE

0: None

1: Slide

2: Flash

Press the [

<] or [>] button to select a desired display speed.

TEXT DISPLAY

SPEED

0: Fast

1: Medium

2: Slow

DISPLAY COUNT Enter a display count data and press this field.

6.

Press the [IMAGE] tab. Then, the Advertisement Message (Image) screen appears.

7.

When setting an image, press a desired field.


10-45


8.

The Image List appears.

9.

Press to select a desired field and press the [SET] button.

The selected image has been assigned in the designated field.

10.



The edited message has been registered.

10-46



10.7 STORE NAME REGISTRATION

10.7.1 CHANGING EXISTING STORE DATA

1.

Press the “STORE NAME” field on the Program Menu Select screen.

2.

The default store data screen appears.

When changing the store data, press the [EDIT] button.

3.

The Store Name Edit screen appears.

4.



10-47


5.


The confirmation screen appears. Then, press the [SAVE] button.

6.

The store name has been changed.

7.

Press to select the address field line and press the [EDIT] button.

8.

The Store Address Edit screen appears.

10-48



9.


10.



11.

The store address has been changed.


10-49


10.7.2 CREATING NEW STORE DATA

1.

Press the “STORE NAME” field on the Program Menu Select screen.

2.

The default store data screen appears.

3.

When creating a new store data, enter the desired store number and press the [PLU] key.

EXAMPLE

Store number “1”

Î


10-50



4.

The Store Name Edit screen appears for the selected store number.

5.


6.



7.

The store name has been registered


10-51


8.

Press to select the “Address” field and press the [EDIT] button.

9.

The Store Address Edit screen appears.

10.


11.



10-52



12.

The store address has been registered.

13.

Enter a desired store number as a default store data and press the “Printer 1” or “Printer 2” display field.

EXAMPLE

Set the store number “1” for printer #1.


10-53


10.8 DEPARTMENT NAME REGISTRATION

10.8.1 CREATING NEW DEPARTMENT NAMES

1.

Press the "Department” field on the Program Menu Select screen.

2.

The Department List screen appears. Then, press the [NEW] button.

3.


4.

The Department Name Edit screen appears.

10-54



5.


6.



7.


8.

When creating more department names, enter a desired department number using the numeric keys and press the [PLU] key on the key sheet.

EXAMPLE

Department number “2”.

Î


10-55



9.

The Department Name Edit screen appears.

10.


11.



10-56



12.


13.



10-57


10.8.2 CHANGING EXISITING DEPARTMENT NAMES

1.

Press the "Department” field on the Program Menu Select screen.

2.

The Department List screen appears.

3.

When changing an existing data, press to select a desired field.

4.

The Department Name Edit screen appears for the selected department.

10-58



5.


6.



7.


8.



10-59


10.9 GROUP NAME REGISTRATION

10.9.1 CREATING NEW GROUP NAMES

1.

Press the "Group” field on the Program Menu Select screen.

2.

The Group List screen appears. Then, press the [NEW] button.

3.


4.

The Group Name Edit screen appears.

10-60



5.


6.



7.


8.

When creating more group names, enter a desired group number using the numeric keys and press the [PLU] key on the key sheet.

EXAMPLE

Group number “2”.

Î


10-61



9.

The Group Name Edit screen appears.

10.


10-62



10.9.2 CHANGING EXISITING GROUP NAMES

1.

Press the "Group” field on the Program Menu Select screen.

2.

The Group List screen appears.

3.

When changing an existing data, press to select a desired field.

4.

The Group Edit screen appears for the selected group


10-63


5.


6.



7.


8.


10-64



10.10 COOKING INSTRUCTION REGISTRATION

10.10.1 CREATING NEW INSTRUCTIONS

1.

Press the "Cooking Instruction” field on the Program Menu Select screen.

2.

The Cooking Time List screen appears. Then, press the [NEW] button.

3.


4.

The Cooking Time Edit screen appears.


10-65


5.


6.



7.


8.

Enter a numeric value for each filed using the numeric keys and press the corresponding field for registration.

EXAMPLE

Base time “35 minutes”

10-66



9.

When creating more instructions, enter a desired cooking instruction number using the numeric keys and press the [PLU] key on the key sheet.

EXAMPLE

Cooking instruction number “2”.

Î


10.

The Cooking Time Edit screen appears.

11.



10-67


1.

Press the "Cooking Instruction” field on the Program Menu Select screen.

2.

The Cooking Time List screen appears.

3.

When changing an existing data, press to select a desired field and press the [DETAIL] button.

4.

The Cooking Time Edit screen appears for the selected instruction

10-68



5.


6.



7.


8.



10-69


10.11 NUTRITION FILE REIGISTRATION

10.11.1 CREATING NEW NUTRITION DATA

1.

Press the "Nutrition (USA)” field on the Program Menu Select screen.

2.

The Nutrition List screen appears. Then, press the [NEW] button.

3.


4.

The Nutrition Data Programming screen for the selected nutrition number appears.

When creating a text for “Serving Size”, press the [EDIT] button.

10-70



5.

The Nutrition Edit screen appears.

6.


7.



8.

The edited text has been registered. Then, enter a nutrition data for each field using the numeric keys and press the corresponding field for registration.


10-71


9.

When creating more nutrition data, enter a desired nutrition number using the numeric keys and press the [PLU] key on the key sheet.

EXAMPLE

Nutrition number “2”.

Î


10.


10-72



10.11.2 CHANGING EXISTING NUTRITION DATA

1.

Press the "Nutrition (USA)” field on the Program Menu Select screen.

2.

The Nutrition List screen appears.

3.

Select a desired nutrition number.

EXAMPLE

Nutrition number “2”. or press the [PLU] key on the key sheet after a numeric entry.

Î


10-73


4.

Press the [DETAIL] button,

5.

The Nutrition Data Programming screen for the selected nutrition number appears.

When changing a text for “Serving Size”, press the [EDIT] button.

6.

The Nutrition Edit screen appears.

7.


10-74



8.



9.

The edited text has been registered. When necessary, enter a nutrition data for each field using the numeric keys and press the corresponding field for registration.

10.

Press the Return button after making necessary changes.

11.



10-75


10.12 EXTRA MESSAGE REGISTRATION

10.12.1 CREATING NEW MESSAGES

1.

Press the "Extra Message” field on the Program Menu Select screen.

2.

The Extra Message List screen appears. Then, press the [NEW] button.

3.


4.

The Extra Message Edit screen appears.

10-76



5.


6.



7.


8.

When creating more messages, enter a desired message number using the numeric keys and press the [PLU] key on the key sheet.

EXAMPLE


Î


10-77



9.


10-78



1.


2.

The Extra Message List screen appears.

3.

Select a desired message number.

EXAMPLE


Press a desired field, or press the [PLU] key on the key sheet after a numeric entry.

Î


10-79


4.

Press the [DETAIL] button.

5.

The Extra Message Edit screen appears.

6.


7.



8.


10-80



10.13 COUPON MESSAGE REGISTRATION


1.

Press the "Coupon Message” field on the Program Menu Select screen.

2.

The Coupon Message List screen appears. Then, press the [NEW] button.

3.


4.

The Coupon Message Edit screen appears.


10-81


5.


6.



7.


8.

When creating more messages, enter a desired message number using the numeric keys and press the [PLU] key on the key sheet.

EXAMPLE


Î

10-82




9.



10-83


1.


2.

The Coupon Message List screen appears.

3.

Select a desired message number.

EXAMPLE


Press a desired field, or press the [PLU] key on the key sheet after a numeric entry.

Î

10-84



4.


5.

The Coupon Message Edit screen appears.

6.


7.



8.



10-85


10.14 POP MESSAGE REGISTRATION

1.

Press the "POP Message” field on the Program Menu Select screen.

2.

The message list screen appears.

3.

Enter a desired message number and press the [PLU] key on the key sheet.

EXAMPLE


Î


10-86


4.

The POP Message Edit screen appears.



5.

P Press the [ESC] key on the key sheet to escape from text editing mode.


6.


7.



10-87


10.15 TAX REGISTRATION

1.

Press the "Tax” field on the Program Menu Select screen.

2.

The Tax List screen appears.

3.

When changing a tax system, press to select a desired field.

ITEM DESCRIPTION

TAX TYPE Press to select one of tax types.

TAX RATE

Exclusive tax

Inclusive tax

Tax exemption

Enter a numeric value and press this field.

10-88



10.16 SCHEME TABLE REGISTRATION

10.16.1 CREATING NEW TABLES

1.

Press the "Scheme Table” field on the Program Menu Select screen.

2.

The Scheme Table screen appears. Then, press the [NEW] button.

3.


4.

The Scheme Table Detail (Basic) screen appears. Then, press the [EDIT] button.


10-89


5.

The Scheme Table Edit screen appears.

6.


7.



8.


10-90



ITEM DESCRIPTION

RETAIN LOT No. Press to select whether or not to use this lot number.

0: No

1: Yes

PASSPORT FORMAT No. Enter a numeric value and press this field.

ICON No. Enter a numeric value and press this field.

LIFE OFFSET

WEIGHT LIMIT CONTROL


Press to select whether or not to control the weight limit.

0: No

DATE LIMIT CONTROL

LOSS %

1: Yes

Press to select whether or not to control the date limit.

0: No

1: Yes

Enter a numeric value and press this field

ITEM DESCRIPTION

LOT/CARCASS Enter a numeric value and press the corresponding field.

GTIN

WEIGHT

Enter a numeric value and press the corresponding field.


PASSPORT LOT START Enter a numeric value and press this field.

PASSPORT GTIN START Enter a numeric value and press this field.


10-91


9.

When creating more tables, enter a desired table number using the numeric keys and press the [PLU] key on the key sheet.

EXAMPLE

Table number “2”.

Î


10.


10-92



1.

Press the "Scheme Table” field on the Program Menu Select screen.

2.

The Scheme Table screen appears.

3.

Select a desired table number by pressing the corresponding field.

EXAMPLE

Table number “2”. or press the [PLU] key on the key sheet after a numeric entry.

Î


10-93


4.


5.

The Scheme Table Detail (Basic) screen appears.

ITEM DESCRIPTION

RETAIN LOT No. Press to select whether or not to use this lot number.

0: No

1: Yes

PASSPORT FORMAT No. Enter a numeric value and press this field.

ICON No. Enter a numeric value and press this field.

LIFE OFFSET

WEIGHT LIMIT CONTROL


Press to select whether or not to control the weight limit.

DATE LIMIT CONTROL

LOSS %

0: No

1: Yes

Press to select whether or not to control the date limit.

0: No

1: Yes

Enter a numeric value and press this field

10-94



ITEM DESCRIPTION

LOT/CARCASS Enter a numeric value and press the corresponding field.

GTIN

WEIGHT



PASSPORT LOT START Enter a numeric value and press this field.

PASSPORT GTIN START Enter a numeric value and press this field.

6.

When changing the table name, press the [EDIT] button.

7.

The Scheme Table Edit screen appears.


10-95


8.


9.



10.

The edited text has been registered. Then, press the Return button.

11.

The Scheme Table screen appears.

12.


10-96



10.17 GEN TABLE REGISTRATION

1.

Press the "GEN Table” field on the Program Menu Select screen.

2.

The GEN Table screen appears.

3.

Select a desired GEN table by pressing the corresponding field.

4.



10-97


5.

When changing the title text, press the [EDIT] button.

6.

The GEN Table Edit screen appears.

7.


8.



10-98



9.


10.



10-99


10.18 LOOKUP TABLE REGISTRATION

10.18.1 CREATING NEW TABLES

1.

Press the "Lookup Table” field on the Program Menu Select screen.

2.

The Lookup Table screen appears. Then, press the [NEW] button.

3.


4.

The Lookup Table Data List screen appears. Then, press the [EDIT] button.

10-100


5.

The Lookup Header Table Edit screen appears.


6.


7.



8.

The edited text has been registered. Then, press the [NEW] button.


10-101


9.


10.

The Lookup Data Table Edit screen appears.

11.


12.



10-102



13.


14.

When registering the next data text, enter the data number and press the [PLU] key on the key sheet.

EXAMPLE

Data number “2”.

Î


15.


16.



10-103


17.



18.


19.

Repeat steps 14 through 18 for more data registrations.

20.

Press the Return button to return to the Lookup Table screen.

21.

The Lookup Table screen appears.

10-104



22.

When registering the next header text, enter the header number and press the [PLU] key on the key sheet.

EXAMPLE

Header number “2”.

Î


23.

The Lookup Table Data List screen appears. Then, press the [EDIT] button.

24.


25.



10-105


26.



27.

The edited text has been registered. Then, press the Return button.

28.

The Lookup Table screen appears

29.

Repeat steps 22 through 28 for more header registrations.

10-106



10.18.2 CHANGING EXISITING TABLES

1.

Press the "Lookup Table” field on the Program Menu Select screen.

2.

The Lookup Table screen appears.

3.

Select a desired header table by pressing the corresponding field.

EXAMPLE

Table number “2”. or press the [PLU] key on the key sheet after a numeric entry.

Î


10-107


4.


5.

The Lookup Table Data List screen appears.

When changing the header name, press the [EDIT] button

6.


7.


10-108



8.



9.


10.

When changing the data text, select a desired data text by pressing the corresponding field. and press the [DETAIL] button.

11.



10-109


12.


13.



14.


15.

Repeat steps 10 through 14 for more data text registrations.

16.

Repeat steps 3 through 15 for more header table text registrations.

10-110



10.19 MINCE TRACEABILITY REGISTRATION

1.

Press the "Mince Traceability” field on the Program Menu Select screen.

2.

The Mince Traceability screen appears.

3.

Enter a numeric value and press the corresponding field for registration.



10-111


10.20 FIXED PRICE MARK REGISTRATION

1.

Press the "Fixed Mark” field on the Program Menu Select screen.

2.

The Fix Price Mark List screen appears.

3.

Enter a desired mark number using the numeric keys and press the [PLU] key on the key sheet.

EXAMPLE

Mark number “6”.

Î


10-112


4.

The Fix Price Mark Edit screen appears.


5.


6.



7.


To finalize this procedure, press the Return button.


10-113


10.20.2 CHANGING EXISITING PRICE MARKS

1.


2.

Select a desired mark number by pressing the corresponding field.

EXAMPLE

Mark number “2”. or press the [PLU] key on the key sheet after a numeric entry.

Î

3.

The Fix Price Mark Edit screen appears.

10-114



4.


5.



6.


7.



10-115


10.21 FREE MESSAGE REGISTRATION


1.

Press the "Free” field on the Program Menu Select screen.

2.

The Free Message List screen appears. Then, press the [NEW] button.

3.


4.

The Free Message Edit screen appears.

10-116



5.


6.



7.


8.

Enter a desired message number using the numeric keys and press the [PLU] key on the key sheet.

EXAMPLE


Î


10-117


Enter a desired message number using the numeric keys and press the [PLU] key on the key sheet.

EXAMPLE


Î


9.


10-118



1.


2.

The Free Message List screen appears.

3.

Select a desired message number by pressing the corresponding field.

EXAMPLE

Message number “2”. or press the [PLU] key on the key sheet after a numeric entry.

Î


10-119


4.

The Free Message Edit screen appears.

5.


6.



7.


8.


10-120



10.22 CHECK LABEL REGISTRATION

1.

Press the "Check Label” field on the Program Menu Select screen.

2.

The Check Label screen appears.

3.

Enter Start Number and End Number using the numeric keys and press the corresponding fields for registration.


10-121


4.

Press the [STRAT] button to print the labels.

10-122


SETUP MODE

11.1 SETUP MODE ENTRY

1.

Make sure that the initial screen is displayed.

Chapter 11 SETUP MODE

11

2.


The Operation Mode screen appears. Then, press the [SETUP] button on the screen

3.

The Setup Menu Select screen appears.


] or [ a






11.2 MACHINE NUMBER SETTING

1.

Press the “MACHINE No.” field on the Setup Menu Select screen.

2.

The Machine Number (Basis) screen appears.

3.

Enter a desired numeric value and press the “Dept No.” field.

EXAMPLE

Dept number “9”

4.

The confirmation screen appears. Then, press the [EXEC] button to continue.



11.3 SALES MODE SETTING

1.

Press the “Sales Mode” field on the Setup Menu Select screen.

2.

The Sales Mode screen appears.

3.

Select a desired mode by pressing the correponding button.

EXAMPLE

“Self-service Mode”


11.4 PASSWORD SETTING

1.

Press the “Password” field on the Setup Menu Select screen.


2.

The Password (Operate) screen appears.


] or [ a


3.

Press the [TOTAL] tab to display the Password (Total) screen.


] or [ a




4.

Press the [PROGRAM] tab to display the Password (Program) screen.






11-7


5.

Press the [SETUP] tab to display the Password (Setup) screen.



6.

Press the [ADJUST] tab to display the Password (Adjust) screen.

7.

Enter a 6-digit password using the numeric keys and press the [PASSWORD] display field on the screen.

EXAMPLE

Password “999999”



8.

Press desired buttons to set whether or not to use the password.

EXAMPLE

Set to apply the password to “Virtual Receipt” in Total Mode.



11.5 KEY LOCK SETTING

1.

Press the “Key Lock” field on the Setup Menu Select screen.

2.

The Key Lock (Display Key) screen appears.

3.

Press the [FUNCTION KEY] tab to display the Key Lock (Function Key) screen.

Press the [ b

] or [ a

] button to change the pages.




11-11




4

Press the [STROKE KEY] tab to display the Key Lock (Stroke Key) screen.

5.

Enter a 6-digit password using the numeric keys and press the [PASSWORD] display field on the screen.

EXAMPLE

Password “999999”

6.

Press a desired mode by pressing the corresponding tab, and press to select desired buttons to set whether or not to use the password.

EXAMPLE

Set to apply the password to “Multi” in Function Key Mode.



11.6 DATA STORAGE SETTING

1.

Press the “Data Storage” field on the Setup Menu Select screen.

2.

The Data Staorage (Total Add) screen appears.

Press the [ b

] or [ a


11-14

3.

Press desired buttons to set whether or not to use the total addition.

EXAMPLE

Set to use the operator total addition.



11.7 PRESET REPORT SETTING

1.

Press the “Preset Report” field on the Setup Menu Select screen.

2.

The Preset Report (Daily) screen appears.

Press the [ b

] or [ a ] button to change the pages.



3.

Press the [WEEKLY] tab to display the Preset Report (Weekly) screen.



4.

Press the [CUMULATIVE] tab to display the Preset Report (Cumulative) screen..

Press the [ b

] or [ a




5.

Press a desired mode by pressing the corresponding tab, and press to select desired buttons to set whether or not to print the totals

EXAMPLE

Set to print the Production Daily Total (Total).



11.8 AUTO PROGRAM SETTING

1.

Press the “Auto Program” field on the Setup Menu Select screen.

2.

The Item Auto Overwrite screen appears.

Press the [ b

] or [ a ] button to change the pages.

Note: Display items may vary depending on the country setting.



3.

Press to select desired buttons to set whether or not to overwrite the items automatically.



11.9 DEFAULT DATA SETTING

1.

Press the “Default Data” field on the Setup Menu Select screen.

2.

The Item Initial Data (Sales 1) screen appears.

ITEM DESCRIPTION

Press the [

<] or [>] button to select a desired Sales Mode.

SALES MODE

0: Weighing product

1: Fixed price product

2: Weighing fixed price product

3: Fixed unit price

Press the [

<] or [>] button to select a desired Markdown Mode.

MARKDOWN

MODE

1: Special price

2: Amount discount for total price

3: Percent discount for total price

4: Special unit price

5: Amount discount for unit price

6: Percent discount for unit price



Press the [

<] or [>] button to select whether or not to allow open prices system.

OPEN PRICE

UNIT PRICE

0: Yes

1: No

Enter a unit price and press this field.

M/D AMOUNT Enter a markdown amount or percentage and press this field.

QTY Enter a quantity and press this field.

Press this field to display the Fix Price Mark List screen.

Then, select a desired price mark by pressing the corresponding field.

EXAMPLE

“Pack Packs”

UNIT TYPE

FIXED PRICE Enter a fixed price and press this field.

TAX Enter a tax number and press this field.

FIXED WEIGHT Enter a fixed weight and press this field.

TARE Enter a tare weight and press this field.

UNDER WEIGHT Enter a lower weight limit and press this field.

UPPER WEIGHT Enter an upper weight limit and press this field.



3.

Press the “SALE 2” tab to display the Item Initial Data (Sales 2) screen.

ITEM DESCRIPTION

Press the [

<] or [>] button to select whether or not to use a point flag.

POINT

FLAG

0: Off

1: On

Press the [

<] or [>] button to select a desired point type.

POINT

0: Weight

TYPE

1: Fixed weight

POINTS Enter a point data and press this field.

4-1

Press the “MESSAGE” tab to display the Item Initial Data (Message) screen.

4-2

Press a desired field to display the corresponding list screen.

EXAMPLE

“Extra Message 1”



4-3

Select a desired message by pressing the corresponding field.

4-4

The selected message has been registered.

5-1

Press the “IMAGE” tab to display the Item Initial Data (Image) screen.

5-2

Press to select a desired image field.



5-3

The Image List screen appears. Then, select a desired image by pressing the corresponding field.

5-4

The selected image has been registered.

5-5

Press the Display Image field.

5-6

The Display Image List screen appears. Then, select a desired image by pressing the corresponding field.



5-7

The selected image has been registered.

5-8

Select whether or not to print safe handling message.

6.

Press the “PRINT” tab to display the Item Initial Data (Print) screen.

11-26

ITEM DESCRIPTION

FIRST LABEL

FORMAT NO.

Enter a desired format number and press this field.

SECOND

LABEL

FORMAT NO.

Enter a desired format number and press this field.

FIRST LABEL

PRINT

Press the [

<] or [>] button to select whether or not to print first labels.

1: Yes

2: No

Press the [

<] or [>] button to select whether or not to print first labels.

SECOND

LABEL PRINT

1: Yes

2: No



7.

Press the “DATE” tab to display the Item Initial Data (Date) screen.

ITEM DESCRIPTION

PACK DATE

Press to select whether or not to print pack date.

PRINT

Press the [


PACK TIME

PRINT

0: No print

1: Designated time

2: System clock time

PACK TIME

DATA

Enter a desired pack time and press this field.

SB DATE PRINT Press to select whether or not to print sell-by date.

Press the [


SB TIME PRINT

0: No print

1: Designated time

2: Relative time

SB TIME DATA Enter a number of “Time After” for sell-by time and press this field.

SHELF LIFE

(DAYS)

Enter a number of days for shelf life and press this field.

UB DATE PRINT Press to select whether or not to print use-by date.

UB DATE DATA Enter a number of days for use-by date and press this field.

8.

Press the “DATE” tab to display the Item Initial Data (Date) screen.

ITEM DESCRIPTION

ITEM CODE Enter an item code and press this field.

REGI CODE

POS FLAG

Enter a register code and press this field.

Enter a POS flag number and press this field.

BARCODE Enter a barcode and press this field.

Press the [

<] or [>] button to select a desired reference method.

POS REFERENCE

0: Refer

1: PLU file



The Barcode Type screen appears when this field is pressed.

Press to select a desired type.

BARCODE TYPE

The Barcode Format screen appears when this field is pressed. Press to select a desired format.

POS FORMAT

TRACE ENABLE Press to select whether or not to enable traceability function.

DEPARTMENT NO. Enter a department number and press this field.

GROUP NO. Enter a group number and press this field.



11.10 PLU UPDATE SETTING

1.

Press the “PLU Update” field on the Setup Menu Select screen.

2.

The PLU Update screen appears.

Press the [ b

] or [ a


Note: Display items may vary depending on the country setting.






11-31


3.

Enter the start and end numbers and press these fileds to specify the target PLUs.

4.

Select desired items by pressing the corresponding fields.


5.

To release the selection, press the selected field again.


To release all the selections, press the [BATCH DELETE] button.



6.

Press the [EXECUTE] button to update the selected items.

7.

Press the [EXEC] button for execution.



11.11 RECEIPT SETTING

1.

Press the “PLU Update” field on the Setup Menu Select screen.

2.

The Receipt Setting screen appears.

To edit the header and footer titles, press the corresponding field.

3.

The Receipt Title Edit screen appears.

4.

Edit the text according to the procedure explained in Appendix “Text Editing”.



5.


6.

To edit the header and footer logo images, press the corresponding field.

7.

The Image List screen appears.

8.

Select a desired image by pressing the corresponding filed, and press the [SET] button.


9.

The edited logo image has been registered.



Appendix TEXT EDITING

TEXT EDITING

A.1 OPERATION PANEL AND KEY FUNCTIONS

Operation Panel

A

Text Editing Keys

Used to delete a character by moving the cursor back by one character.

Used to delete a character at the place where the cursor is positioned.

Used to delete a line text.

Used to specify a normal character style.

Used to specify a bold character style.


Used to select a font size for a text displayed on the screen.

Used to insert a character, or select characters followed by depressions of the [

→] or [←] key.

Used to move the cursor to right. Also used to select characters for changing the style.

Used to move the cursor to left. Also used to select characters for changing the style.

Used to select either lower-case or upper-case character mode for a text to be entered.

A-1


Used to specify an Italic character style.

Used to specify an underlined character style.

Used to specify a revered character.

Used to enter a space at the place where the cursor is positioned.

Used to copy the original data to the current data.

Used to finalize editing a text.

Used to begin a new character line.

Used to select either a lower-case or upper-case mode for a character to be entered.

A-2 UNI-5 User’s Manual


A.2 NORMAL CHARACTER EDITING

1.

Confirm that the text edit screen is displayed.

Select a desired character size by using the [Size] key on the key sheet.

The selected size is displayed in the “FONT” display field.

2.

Press the [Lower Case] key on the key sheet to select whether to use upper-case characters or lower-case characters.

UNI-5 User’s Manual A-3


3.

Enter desired characters using alpha-numeric keys on the key sheet or the screen.

Upper-case characters

Lower-case characters



4.

To change to a new line, press the [New Line] key on the key sheet.

Enter desired characters.

5.

To finalize the editing, press the [ESC] key on the key sheet.




A.3 SPECIAL CHARACTER EDITING

1.

Confirm that the text edit screen is displayed.

2.

To select a desired character style using the following keys.

The selected style is displayed in the “STYLE” display field.

EXAMPLE

Select reversed characters.

A-6

3.

Enter desired characters using alpha-numeric keys on the key sheet or the screen.



4.

Press the [ESC] key on the key sheet.




A.4 LINE DELETION

1.

Confirm that the text edit screen for a desired PLU is displayed.

2.

To delete the character line, press the [Line Delete] key on the key sheet.

A-8

3.





A.5 CHARACTER DELETION

1.

To Make a correction for a misspelled word, move the cursor to a place where misspelling is made by using the [

→] or [←] key.

EXAMPLE

“GAUDA”

→ “GOUDA”

or

2.

Press the [Character Delete] key on the key sheet to delete the misspelled character.



3.

Enter the correct character using the alpha-numeric keys.

4.





A.6 CHARACTER BACKSPACING

1.

To delete a wrong character that was just entered, press the [Back Space] key on the key sheet to move the cursor back by one character.

EXAMPLE

“E”

→ “A”

2.

Enter a correct character.



3.

Complete the text.

4.




44 SANNO-CHO, SHOGOIN, SAKYO-KU

KYOTO, 606-8392 JAPAN

PHONE: 81-75-771-4141

FACSIMILE: 81-75-751-1634

URL: http://www.ishidajapan.com

Design and specifications are subject to change without notice.

User`s Manual

User’s Manual

ADJUSTMENT MODE

BEFORE USE

LABEL ISSUE

RECEIPT ISSUE

TRACEABILITY PRODUCTS

TEMPORARY CHANGE OPERATIONS

SELF-SERVICE OPERATIONS

ACCUMULATOR MODE

TOTAL ADJUST MODE

TOTAL MODE

PROGRAM MODE

SETUP MODE

TEXT EDITING

Related manuals

ISHIDA

UNI-7

Rice Lake

Uni-9 Elevated

ISHIDA

IP-AI

Rice Lake

ISHIDA Uni-3

ISHIDA

BC-4000TEC

Mettler Toledo

SmartTouch UC-ST

Rice Lake

Ishida Uni-7 Series

ISHIDA

Omni-4000ST