advertisement
bPro
Scale / Printer
Technical Manual
72186164
1
bPro – T2 bPro – C2 bPro – U2 bPro – U3/U4 bPro – R2 bPro – H2
©Mettler-Toledo, Inc. 2000
No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose without the express written permission of Mettler-Toledo, Inc.
U.S. Government Restricted Rights: This documentation is furnished with Restricted Rights.
2
INTRODUCTION
This publication is provided solely as a guide for individuals who have received Technical Training in servicing the METTLER TOLEDO product.
Information regarding METTLER TOLEDO Technical Training may be obtained by writing to:
METTLER TOLEDO
111 West Taihu Road, Xinbei District
Changzhou, Jiangsu, China
(+86) 519 8664-2040
FCC Notice
This device complies with Part 15 of the FCC Rules and the Radio Interference Requirements of the Canadian
Department of Communications. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
METTLER TOLEDO RESERVES THE RIGHT TO MAKE REFINEMENTS
OR CHANGES WITHOUT NOTICE.
3
4
PRECAUTIONS
READ this manual BEFORE operating or servicing this equipment.
FOLLOW these instructions carefully.
SAVE this manual for future reference.
DO NOT allow untrained personnel to operate, clean, inspect, maintain, service, or tamper with this equipment.
ALWAYS DISCONNECT this equipment from the power source before cleaning or performing maintenance.
CALL METTLER TOLEDO for parts, information, and service.
5
CONTENTS
6
7
8
1
Specifications
General Description
The METTLER TOLEDO bPro is a digital computing scale with an integrated thermal label printer. It is an Ethernet scale with a wireless option, which has a database containing the PLU’s, Extra Text and etc. A PC program is available to download or upload the database from the PC. The bPro has 4
MB RAM memory and 4MB Flash ROM. The PLU memory can handle up to
25000 items.
The standard bPro weighing capacity is 15 Kg ( 30 Lbs). Weighting resolution can be set up for a single range with 0.005 Kg (0.01 Lbs) or a dual interval option for 0.002 Kg (0.005 Lbs) from 0 to 6 Kg (15 Lbs). In the dual interval, the single range resolution applies between 6 -15 Kg
(15-30 Lbs). Weighting options for 30 Kg (60 Lbs) are also available.
This scale utilizes a dot matrix display that will display weight, tare, unit price and total price, as well as item description.
The bPro, like all METTLER TOLEDO products is designed for maximum durability and reliability in even the most demanding application environments. The bPro is manufactured in one of METTLER TOLEDO's ISO
9001 and ISO 14001 certified facilities so you are assured to receive a high quality product.
1
2
Features
• 6kg, 15kg, 30kg (3000e or 3000e dual range)
• Full Dot Matrix display with 240x240 resolution on both operator side and customer's side.
• Four seven-segment numeric display for: 5 digits weight, 5 digits tare, 7 digits unit price and 7 digits total price. One 16-character alphanumeric display for programming and item description.
• Indicators for zero, net and prepack mode.
• Compliance with H44 3000e, R76 OIML 3000e and Canadian W&M.
• Light Touch Tactile feel membrane keyboard and an audible beeper.
• A 70 position preset keyboard for fast PLU retrieval. (can save 140 PLU in two levels) Includes QWERTY keypad in programming mode for easy PLU editing.
• Real time clock and RAM are backed up by a rechargable lithium battery with at least 1 month memory retention without external power.
• Push button zero (auto zero at power up) and automatic zero tracking.
• Price, Shelf Life, Quantity, and Extra Text, Label Format, and SPEC Message override capability.
• VOID key for clearing previous transaction from accumulator.
• Computer interface port (RS232), or Ethernet for use with BSOFT software.
USB port for PLU updates (Future)
• Integral thermal label printer with 8 dots/mm print head. Adjustable 40 to
60mm width. Supports both UPC and EAN symbology. The printer can use die cut labels, continuous strip labels and continuous thermal paper.
Customer/Vendor
Display
Indicates that a tare has been entered and the weight is NET.
There are two displays on the scale, one is on the vendor side and the other is on the customer side. They are all mounted on the tower except bPro-C2 model.
These two LCD displays incorporate a yellow color LED backlight. Both the customer and vendor displays show 5 digits of weight, 5 digits of tare, 7 digits of unit price and 7 digits of total price values along with cursors for Zero, Net and Prepack mode.
Both the customer and vendor displays can also show 16 alphanumeric characters for commodity description, marquee and prompt messages during programming.
The Weight display characters are 13.2mm high by 8.16mm wide. The Tare
Weight, Unit price and Total Price display characters are 11mm high by 6.6mm wide. The alphanumeric characters are 8.36mm high by 4.18mm. The display legends definitions are shown in the figure below.
Another 240x240 full dot matrix display, this can enable display Chinese, Thai language, Arabic etc, special offers to increase in-store scales.
Shows the normal weight.
The zero cursor indicates that the scale is within the zero range, either net or gross zero. If the display does not read 0.00 at ready, press the zero key.
Shows the Tare weight.
Shows Unit price.
Shows Total price.
Shows PLU description
3
4
Keyboard
The keyboard consists of membrane layer, rubber button layer, programming layer, operating layer and touch pad layer. The multi layer makes it easy to press the key which we call it light touch tech. The layers are replacable and you can take them down and wash them with water (except the membrane layer). This will make maintenance much easier.
The 28 keys on the right keypad are used for entering basic scale functions.
Operating Layer (T2 model)
Programming Layer (T2 model)
The keyboard can be adjusted to 4 levels according to customers’ wish. Only T2 and C2 models have this function.
Meaning of the function keys
Ä
Free entry of a price per piece
Ó
Continue
°
(PRINT,V2,V3,V4）Vendor, clerk
Ô
Go back
Ò
[TARE] Tare c
Clear;
0
Zero
Ç
Customer total , Confirm
[CODE] Code and switching
Æ
Manual entry of a price per piece to add v
Mode and switching
Å
Manual entry of a price per piece to subtract
»
Paper feed x
Multiplication
[FIX] Fixed unit price / fixed tare r
Change back
³
Void
Special functions o
Pressing CONFIG than PRINT will list the scale information on a label such as software version, IP address, MAC Address, scale type, scale ID, as well as the Product ID of the scale. o
Power On while pressing Print to access the Serial Flash mode for Wait for
Host o
Power On while pressing clear (C) to access the Network Flash mode o
Power On while pressing CODE to access display mode selection
Some type has the [TM] key, used to Tare manually.
Special functions keys
1 to 70
V2,V3,V4 preset keys vender keys V2-V4
[-%] increase/decrease key (Discount key)
Note: The left 70 keys are preset keys which can store 140 PLUs for fast
PLU retrieval. Different type has different quantity preset keys.
5
6
Remark :
*V2, V3 and V4 key can be configured as preset keys or vender keys, but one function is available at one time.
* [-%] key can be configured as preset key or increase/decrease key, but only one function is available at one time.
The following function keys can be used as word processing keys while entering
PLU description, store address, Extra Text and etc.
Meaning of the 'programming" keyboard keys h
Go to beginning of text e
Go to end of text
^ move the cursor one position left in the text edit mode
] move the cursor one position right in the text edit mode
Ó
Go to next sub-menu
Ô
Return to previous sub-menu s
Get upper case characters in text edit mode or select a key's 2nd function q
Alternate: special characters in text edit mode b
Backspace (delete the character left of the cursor)
[DELETE] Delete (delete the character on the cursor)
[iNSERT]
[ ABC ] Center the text in text edit mode
[ENTER] Carriage return (next line)
Ç
Selection of a menu
The 70 keys on the left keypad can be programmed as direct access keys (Presets).
There are two levels to the preset keys for a total of 140 PLU Presets. The Preset keys should be configured first before being used. Please refer to section 3 ‘PLU Preset’ for programming the Preset keys.
To recall a PLU simply select the proper level and press the desired preset.
Dimensions
bPro-T2 bPro-U2
7
8 bPro-C2 bPro-R2
bPro-H2
9
bPro-U3
Weighing Capacity
The bPro can be programmed for 3/6x0.001/0.002, 6/15x0.002/0.005kg,
15/30x0.005/0.010kg capacities. The built-in scale is designed to withstand static overloads up to five times the rated capacity without sustaining permanent damage.
A weight greater than five increments over capacity causes the weight display to
"-----" and printing is inhibited. If the scale is under zero by more than five increments, the weight field will display dashes "|_____|". When zero can not be captured, the weight field will display "-----".
10
Tare
Tare is limited to a maximum of 2/3 full capacity.
Memory Specifications
The Main Logic PCB contains a rechargable lithium battery that will retain backup
PLU's and the time/date in the SRAM memory for up to one month. Other data, including calibration data are retained in the EEPROM which requires no battery for memory retention.
Agency Approvals
The model bPro is designed to meet the requirements of the following agencies:
OIML R76 standard OIML
EC
NIST
Euro CE standard
NTEP requirements for Class III weight device.
NTEP/California Electronic Cash Registers General Code
Requirements
FCC Requirements for FCC Conducted Emissions and Radiated Emissions for a Class A device.
Electrical
The bPro requires a dedicated grounded 100/240 VAC, 50/60 HZ supply, and draws 0.3 amps (scale/printer versions). The AC line (including ground) must not be shared with noise and surge generating equipment such as, electric motors, compressors, thermostats, fluorescent lights, etc. A line conditioning device is
11
recommended to provide protection from surges and spikes. The Power supply uses an electronic overload protection circuit designed to protect the internal electrical components.
12
Label Printer
Labels can be printed with the built-in thermal label printer. The printer uses a
60mm wide, high resolution, 8 dots/mm, thermal print head. The printer driver PCB incorporates a heat detection circuit to ensure the best possible print quality while eliminating any possibility of overheating the head. Overheating is the major cause of premature print head failure. The print speed and density can be adjusted via
SERVICE MODE to compensate for varying types of labels.
The printer can use standard label sizes ranging from 25mm to 102mm long, and continuous strip stock. Labels can be loaded in a stripped or un-stripped mode. In stripped mode, the labels automatically peel from the backing liner. In the un-stripped mode, the label and liner will be delivered. A tear/bar allows continuous stock to be torn to exact length needed. Print specifications for the thermal printer are as follows:
PRINTHEAD TYPE:
DOT DENSITY:
PRINT SPEED:
Thick Film Thermal Printhead
8 Dots/mm
125 mm/sec maximum
Printer 2“ paper dimensions
A
B
C
A
Dimensions Labels
Min. Max.
A 30 mm 82 mm
D
B 130 mm
C 40 mm
D 30 mm 82 mm
E
F 25 mm 102 mm
G 56 mm eff. print width,
The print head is centred over
E the paper.
E
Print resolution: 8 Pixel/mm
F
Dimensions Receipt
F
G
A 52 mm
B 130 mm
C 11 mm
Paper length max: 150 m
13
Operating & Storage
Temperature
Operating Range:
Storage Range:
-10°C to 40°C (14°F to 104°F), humidity from 5% to
85% non-condensing.
0°C to 70°C (32°F to 158°F), humidity from 5% to 85% non-condensing.
Database Records
The PLU database file consists of:
Field Name Description
PLU Number Price Look Up number used for database indexing and to call up a record
Item Number
Description 1
Description 2
Range
0 – 999999
The product number is a number that is encoded in the EAN Bar Code symbol. This
0 – 9 each character number can be inputted up to 13 digits.
Text used to describe the product for line 1 28 char/line
Text used to describe the product for line 2 Up to 150 characters,10
Group No A two digit number between 0 and 99 used for reports; 0 is no group lines
0 – 99
Unit Price
2nd Unit Price
Price Rule No
Product unit price: Price per lb by weight or Price per piece
Second unit price. Depend on the price rule
Decide the Unit Price.
0,1: 1 st Unit Price 2: 2 nd Unit Price
3 -10: link to discount number
0.00 to
99999.99
0.00 to
99999.99
0 -10
Label Format This will contain the label format number.
0 = scale default. 101 through 109 are fixed formats. Others are custom label
0 – 199
2 nd Label Format formats.
Number for second label. 0 – 199
Best Before Days This is the number of days from the current 0 – 999
14
Sell By Days date that the item can be used
This is the number of days from the current date that the item can be sold
PLU Type By-Weight; By Count;
Tare/By Count No Tare number for by weight PLU;
Quantity for by count PLU
Fix Weight The Net Weight of By Count PLU
Extra Text
Number
This is the extra text number to be used with this PLU. ‘0’ means no ET will be added.
Increase/Decrease Allow PLU to have a discount
Allow Price
Change
This allows price changes during normal operation.
NUTRITION No. Number of Nutrition
Pack date print Print format for packing date
Best before print Print format for Best Before date
Sell by print
Graphic No.
Print format for Sell by date
Number of Graphic link to PLU
0 – 999
0/1
0 – 99/0-9999
0.00 – 99.999
0 – 999999
0/1
YES/NO
0-999999
0-4
0-5
0-5
0-200
15
Major Component Map
External Components
A
E
F
E
B
G
D
Ref Description
A Display
B Tower
D Printer
16
D
A
C
Index of Specifications
bPro - X X - X XX X- X 0X -X xxx
Type
T=Tower, C=Compact
U=Upper Keyboard
H=Hanging, R=Terminal
Style
3=Self service
Display
CAPACITY
B=Dot
Load Cell
Extension Memory
Extension
Network
PRINTER
Country finish code
17
18
2
Installation
Unpack the Shipping Carton
Open up the package box. Take out the platter ,attachments, then take out the scale.
Remove the foam inserts and plastic bag. Put the scale on the working counter and inspect for damage. Report any damage to the carrier promptly. DO NOT LIFT THE
SCALE USING THE SPIDER OR BACK DISPLAY. Verify you received the accessories listed below.
Tower bPro scale
Platter
Power cord
Operator manual
Security Seal and Quality Feedback card etc.
Note: If you choose to dispose of the package, please recycle the materials. The packaging is recyclable natural fiber with biodegradable adhesives.
Setup Checklist
Leveling
Install Tower
Install platter
Install label
Calibration
Reset RAM
Password keyboard
Operator Configuration
Label format
Barcode
Date/Time
Software
Ievel the unit using the feet for adjustment and bubble indicator as a guide.
Install Display Tower.
Put on the platter to scale.
Install labels in the printer.
New scales must be calibrated on site.
Initialize the scale and set all softswitches to factory default.
To configure the passwords of the specific menus.
To configure the function keys and directly access keys of the keyboard.
To configure printed media, individual label or ticket or total label.
To configure default label format.
To select bar code type.
To set up current date and time.
BSOFT program, which can be used to download or restore the PLU record, configuration, or other data.
19
Leveling
Adjust the four feet until the bubble, located under the scale platter, is in the center of the bubble level. Then adjust the foot locks until the feet are secure.
Bubble Level
Correct Incorrect
20
Install Tower
Tower Model
Take out the tower and insert it into the tower base. Connect the two flat cables together between the tower and the display base. Install four screws on both sides of the display base to lock the tower in place.
Upper Keyboard Model
Connect the two flat cables together between the tower and the display base.
Install four screws on both sides of the display base to lock the tower in place.
Install Platter
Power On
Take out the platter and put on to the scale.
Note: If unit has been stored or transported in below freezing temperatures, allow the unit to warm up to room temperature before turning on AC power.
Remove the power cord from the package box. Install the power cord in the recepticle on the bottom of the scale. Connect the power cord to AC power. Set the power switch to the ON position. Allow at least 30 minutes warm-up time before initial calibration.
21
22
Label Installation
Open the plastic door on the right side of the scale.
Slide out the printer.
Press the trigger to open the printer head.
Install the labels according to the instruction legend on the printer frame.
Pull out the take-up spool Insert the liner into the spool slot. Push back the spool.
Secure the liner on the take-up spool by spinning the spool clockwise.
Close the printer head gently, until it clicks.
Slide the printer into the scale. Close the plastic door.
Press the ` key to bring the label into the start position.
Note: Please refer to section 3 ‘Label Format’ to set the proper label format.
Calibration
Sealing Screw
Base
Calibration Switch
Cal Switch
Sealing screw
AD PCB
Steps ：
1. Snip sealing wire
2. Screw out sealing screw
3. Operation: operation
" [CODE] 9*
"05*
"1
"*
SELECT THE FILTER
"*
"Push Calibration button
" (Input GEO value)
"* display comments
SERVICE FUNCTION Enter service mode menu
Select calibration sub-menu
DO NOT ENTER CAL 0-1
Enter calibration
＝
QUIET
PUSH CAL BUTTON
SELECT GEO 12
0=QUIET;1=NORMAL;2=DISQUIET
Push the calibration button
23
"*
" (Input capacity)
"*
WEIGHT UNIT kg
CAPACITY 15
INC.0.002/0.005
Input capacity of scale
"Select interval with up arrow key [ ] Select interval of the scale
"*
"*
"Input the standard weight value you want to put on scale
"put on the standard weight on platter
"*
CAPTURE 0 ———
ADD WEIGHT 0.000
Read zero
Input the standard weight value you want to calibrate, at least 2/3 of capacity
DONE
SHUT DOWN
Power off scale and power on again
NOTE：
IN THE PROCESS IF GIVE THE MESSAGE “ INIT. CELL...”, WHICH INDICATE THE FAULTCALIBRATION.
24
26
3
Setup
Menu Tree for Scale Setup
Navigating within the Setup Menu
• 【ENTER】 Selects displayed item and moves to sub menu level, accepts the variable in the list.
• 【CODE】
• 【↑】
• 【↓】
• 【Clear】 a warning message
Backs up one menu level, does not accept change.
Moves Up to next menu item, will wrap around from the last entry to the first.
Moves Down to next menu item, will wrap around to end from the first entry.
Clears inputted Text for that field. Clear is also used to clear the PLU and clear
( Direct access numbers
Delete an entry
Code version
Kxxxxxx*xx
C
K* )
Menu Tree
To enter setup mode, press the [CODE] key
Press [CODE] key to return to the first option in the current menu. Press [CODE] key again to return to the previous menu. To exit out of SETUP mode, press [CODE] when the display shows normal weigh state.
DATA ENTRY
1
PRICE CHANGE
CREATE PLU
COPY PLU
EDIT EXTRA TEXT
LIST PLU
DELETE PLU
DEFINE PRESETS
LIST PRESETS
STANDARD PRESETS
DELETE PRESET
CREAT GROUP
LIST GROUP
DELETE GROUP
CREATE SP. OFFER
SP. OFFER BACKW.
DELETE SP. OFFER
LIST SP. OFFER
TARE
CREATE BARCODE
TICKET HEADER
TICKET BOTTOM
RUNNING MESSAGE
CREATE OPERATOR
LIST OPERATOR
DELETE OPERATOR
SHOP NAME
ADVERISEMENT
DATE TEXT
DATE / TIME
DISCOUNT
PACK DATE OFFSET
LOGO MESSAGE
STORE LOGO NUM
MENU END
111
112
114
115
106
107
108
109
110
101
102
103
116
126
127
140
141
142
143
144
145
146
147
148
149
148
128
129
130
132
135
136
138
139
210
211
212
213
214
215
216
218
219
201
202
203
204
205
206
207
208
REPORTS
2
RESET TO DEFAULT
SALES REPORT
PLU REPORT
PROMOTE RPT
GROUP REPORT
GROUP H REPORT
HOURLY REPORT
SETTLE REPORT
ST/VOID REPORT
VENDOR REPORT
CASHDRAWER
REPORT
WEEKLY REPORT
MONTHLY REPORT
YEARLY REPORT
COMBINE REPORT
CLEAR REPORTS
MENU END
501
502
503
504
401
402
403
404
301
302
KEYBOARD CONFIG
3
STANDARD CONFIG
FUNCTION KEYS
303 SPECIAL KEYS
304
305
LIST CONFIG
MENU END
OPERATOR CONFIG
4
STANDARD CONFIG
NEW CONFIG
LIST CONFIG
MENU END
SCALE CONFIG
5
STANDARD CONFIG
NEW CONFIG
LIST CONFIG
MENU END
630
631
632
633
634
635
624
625
626
627
628
629
636
637
639
640
641
642
619
620
621
622
623
643
CODE
601
602
SPECIAL FUNCTION
6
COUNTRY FINISH
ROUND PRICE
603 DISCOUNT ROUND
605
606
607
608
609
610
611
612
616
617
618
UNIT OF PRICE
UNIT PRICE PRINT
PRINT PRICE UNIT
WEIGHT UNIT PRINT
IF PRINT WGT. UNIT
PRINT WITH
MOTION
PRINT LESS 20E
AMOUNT 0 PRINT
PLU FORMAT SKIP
PLU INPUT TYPE
PLU NO. LENGTH
PLU NO. PREFIX
ET LINK TO PLU
PRICE OPEN TYPE
DISCOUNT TYPE
SPECIAL OFFER
OPEN PRICE MARK
OPEN PRICE MODE
UNIT OF BY-COUNT
FIX KEY
FIX KEY IN PREPACK
2ND LABEL PRINT
YEAR LENGTH
DATE FORMAT
DATE SEPERATOR
TIME FORMAT
MEMORY CHECK
SELL BY FORMAT
PACK DATE PRINT
WIRELESS OPTION
PLU DESC DISPLAY
PRECIOUS PRICE
IP LST BYTE MASK
SWITCH NET MODE
DISPLAY NEGA.
WEIGHT
701
702
703
704
705
706
707
708
801
802
803
804
805
806
807
LABEL CONFIG
7
SERVICE BY-WEIGHT
SERVICE BY-COUNT
PREPACK
BY-WEIGHT
PREPACK BY-COUNT
TOTAL LABEL
COPY LABEL
DELETE LABEL
MENU END
PASSWORD
8
STANDARD CONFIG
MANAGER
PASSWORD
SCALE PASSWORD
CODE PASSWORD
PRICE CHANGE PSW.
DISCOUNT PSW.
CLEAR PASSWORD
910
912
913
915
917
918
928
929
932
933
934
935
936
937
938
941
919
921
922
924
925
926
901
902
903
904
905
906
907
908
909
SERVICE MODE
9
FUNCTION TEST
MEMORY TEST
INTERFACE TEST
HIGH RESOLUTION
CALIBRATION
ERROR REPORT
APPLICATION
PRIMARY CONFIG
TICKET NO. TO 0
SET FILTER
CLEAR BRAM
FONTS TABLE
WORK CONFIG
DELET ALL PLU
DELETE ALL GROUP
DEL. ALL OPERATOR
NETWORK CONFIG
SOFTWARE LOAD
TICKET PRINTER
LABEL PRINTER
CONFIG INTERFACE
HEAD CLEAN ALERT
CHANGE PAPER MSG
COMM DEBUG
ASSERT DEBUG
CASHDRAW TEST
WIRELESS CONFIG
USB TEST
PRINT ALL TEXT
PRINT MENU LIST
CHECK FONT
27
644
646
648
649
650
651
652
CHANGE LANGUAGE
PLU NO. Length
EAN13 Style
PP PLU INPUT
CHAIN TARE
MARK DOWN
PLU DISPLAY FONT
28
Enter setup
To enter setup mode, press the [CODE] key.
Exiting setup
Mode functions
Press [CODE] key to return to the previous menu. To exit out of setup mode, press
[CODE] when the display shows normal weigh state.
Press
M
Call the menu "MODE CHANGE"
29
Overview of mode functions
M Call the menu "MODE CHANGE"
MODE CHANGE
_
00 SERVICE
_
01 VOID Operation
_
02 PREPACK
_
03 CODE-MODE
_
04 TRAINING-MODE
_
08 LARGE SALES
_
09 MENU END
With _ Q select the desired sub-menu, or enter the preset code.
Select/return to service mode.
Select/return to void operation mode.
Select/return to prepack mode.
Select/return to code mode.
Select/return to training mode.
Select/return to large sales mode.
Press _ to continue or
*
to return to weighing mode.
With _Q or the preset code, select the corresponding menu item, then activate it with the
*
key.
-For all weighing functions, registering, data entry and sales reporting
-Learning and practical exercises on the device, without the realized turnover being memorized.
-The "TRAINING"
-VOID OPERATION AFTER CHECK OUT means the ticket or label has been printout, and
these transactions will be deleted from the statistics data.
-For packing fieldwork of the supermarket. In this application, only print label, the small variety but large quantity print-work.
-When the article is too big to weigh, operator can enter this mode by inputting the article weight and count price.
30
SCALE CONFIGURATION
K5* Call the menu "Scale configure", this menu for distributing the memory of scale.
new configuration:
SCALE CONFIG.
_
02 NEW CONFIG.
*
RAM FOR PICTURE
_
plu description 2
_
number of plu
_
NF numbers
_ extra text size
_ extra text
_
config. no
MODE CHANGE
_
01 STANDARD CONFIG.
_
02 NEW CONFIG.
_
03 LIST CONFIG
_
04 MENU END
200
28
12000
100
200
1000
0-1
Enter preset code 02
Enter the RAM size for the pictures includes STORE LOGO, PLU
Graphics, SafeHandling, Screen Saver. Range 0-500.
Enter the quantity of PLU DESCRIPTION 2 characters. Range
0-150.
Enter the quantity of PLU in the scale. Range 50-25000.
Enter the Nutritional facts quantity. Range 0-100.
Enter the max. extra text size of each one.
Range 0-500.
Enter the extra test quantity for the scale. Range 0-20000.
(Actual number depends on previous setting, use the rest memory after previous data). whether to save the change 0=no;1=yes
Will show the actual number for PLU QTY, ET size and QTY.
31
DATA ENTRY
K1*
Call the "DATA ENTRY" menu
DATA ENTRY
01 price change
02 create plu
06 edit extra text
07 list plu
08 delete plu
09 Define presets
10 list presets
11 standard preset
12 delete preset
14 create group
15 list group
16 delete group
26 create sp. offer
27 sp. offer backw.
28 delete sp. offer
29 list sp. offer
32
30 tare
32 create barcode
35 ticket header
36 ticket bottom
38 running message
39 create operator
40 list operator
41 delete operator
42 shop name
43 advertisement
44 date text
45 date / time
46 discount
47 pack date offset
48 logo message
49 store logo number
50 menu end
Select desired menu with _Q
or enter preset code and activate with
*
key.
33
price change:
DATA ENTRY
_ enter the preset code 01
01 PRICE CHANGE
* plu number or preset
*
0 enter the PLU number or press the preset key to choose PLU
UNITPRICE
*
0.00
enter new price create plu:(each item can be chosen in menu "code-6-16(plu format skip)"
DATA ENTRY
_
02 create plu
*
plu Number
_
art. Nr.
_
ENTER TEXT
*
0
0
-
ENTER TEXT 2
*
GROUP NO.
_
UNIT PRICE
_
SECOND PRICE
_ price rule no.
_ label no.
_
second label no.
_
TARE NUMBER/QTY PER ITEM
_
-
0
0.00
0.00
0
0
0
0
Press the _
key twice or enter the preset code 02.
Enter the PLU number.(1~999999)
Enter the article number (up to 13 figures).
Enter the commodity text (up to 28 characters)
Enter the 2nd commodity text (up to 150 characters, see
SCALE CONFIGURATION, 10 lines as use _ key to change )
Enter the article group number. (1~99)
Enter the unit price. (0~9999.99)
Enter the second price if necessary. select which unit price as calling out PLU. 0,1: 1 st Unit Price 2:
2 nd Unit Price;3 -10: link to discount number
Input the label number (0-108, 101~108 are fixed label formats)
Input the second label number if necessary.
Tare number for by weight PLU 0=no tare, 1~16=tare number
Quantity for by count PLU 0-9999
34
best bef.offset
_
sell by offset
_ by weight
_
fix weight
_
EXTRA TEXT NUMBER
_ no in/decrease
_ open price yes
_
NUTRITION NO.
_
PRINT PACK DATE
_
SELL BY PRINT
_
BESTBEFORE PRINT
_ copy PLU:
DATA ENTRY
_
03 COPY plu
*
plu Number old
_
plu Number new
_
K
K
0.00 0.00 0.00
0
0
0
0
0
0-1
0
0
0-1
0-2
0-2
0
0
Enter the best before offset(0~999)
Enter the sell by offset(0~999)
Is it an article per piece or a weighed article ?
0 = weighed article,1 = article per piece
Enter the FIX WEIGHT for article per piece
Enter the Extra text number
0=don't allow in./decrease
1=allow in./decrease
0=price can't be changed
1=price can be changed by # key
Enter the nutrition number if print the pack date,0- 4
Not print/yymmdd/mmdd/mmddyy/ddmmyy
SELL BY DATE format,0-5
Not print/yymmdd/mmdd/mmddyy/ddmmyy/days
BEST BEFORE DATE format,0-5
Not print/yymmdd/mmdd/mmddyy/ddmmyy/days enter preset code 03 enter PLU number enter PLU number copy next plu, return to weighing mode
35
Edit Extra text:
DATA ENTRY
_
06 edit extra text
* extra text number
_ enter text
_
K
K
0.00 0.00 0.00 list PLU:
DATA ENTRY
_
07 LIST plu
*
FROM PLU NUMBER
_
TO plu Number
_
K
0.00 0.00 0.00 delete PLU:
DATA ENTRY
_
08 delete plu
*
PLU NUMBER
_
DELETE NO
_
K K
0.00 0.00 0.00
0
-
0
0
0
0-1
36 enter preset code 06 enter extra text number enter the Extra text (use the
*
you can change line) return to weighing mode enter preset code 07 enter PLU number(0=all PLU) enter PLU number(0=all PLU) enter preset code 08 enter PLU number
0=not delete;1=delete clear next PLU return to weighing mode
define preset keys:
DATA ENTRY
_
09 DEFINe presets
* l1 PLU KEY
PLU NUMBER
_
K
K
0.00 0.00 0.00 list preset keys:
DATA ENTRY
_
10 LIST presets
*
K
0.00 0.00 0.00 standard preset key:
DATA ENTRY
_
11 STANDARD preset
*
ALLOCATION NO
_
K
0.00 0.00 0.00
FXX
0
0-1 enter preset code 09 press a preset key(you can choose the layer L1 or L2 by press the key Q )L1=level 1 ;L2=level 2 enter the PLU number define next preset key return to weighing mode enter preset code 10 print the list enter the preset code 11
0=not allocate,1=automatic allocation by the system(plu
1-F001)
37
delete preset key:
DATA ENTRY
_
12 delete preset
*
DELETE NO
_
K
0.00 0.00 0.00 create article group:
0-1 enter the preset code 12
0=not delete,1=all preset keys are cleared return to weighing mode
DATA ENTRY
_ enter preset code 14
14 create Article Group
*
ARTICLE group
ENTER TEXT
0 enter group number
_ enter group name(18 characters)
___ list article group:
_
0
Input the TAX of this group
VAT ?
_ difine next group
K K return to weighing mode
0.00 0.00 0.00
DATA ENTRY
_
15 list Article Group
*
FROM GROUP
_
TO GROUP
_
K
0.00 0.00 0.00
0
0 enter preset code 15 enter group number (0=all group) enter group number (0=all group) printing the list of group return to weighing mode
38
delete article group:
DATA ENTRY
_
16 delete Article Group
* group NUMBER
_
0
DELETE NO
_
0-1
K
K
0.00 0.00 0.00 create special offer:
DATA ENTRY
_
26 create sp.offer
*
ENTER TEXT
___ from
_
00-00 to ?
_
00-00
Plu number
_
0 special offer
_
K
K
0.00
0.00 0.00 0.00 enter preset code 16 enter group number
0=not delete;1=delete delete the next group retun to weighing mode enter preset code 26 enter the detail of special text enter the start time for all special offer enter the end time for all special offer enter PLU number enter the special offer PRICE return to weighing mode
39
forbid special offer:
DATA ENTRY
_
27 sp. offer backw.
* plu number
_ back NO
_
K
K
0.00 0.00 0.00 delete special offer:
DATA ENTRY
_
28 delete sp. offer
* delete no
_
K
0.00 0.00 0.00 list special offer:
DATA ENTRY
_
29 LIST SP. OFFEr
*
KK
0.00 0.00 0.00
0
0-1
0-1
40 enter preset code 27 enter PLU number
0=No prohibition, 1=Prohibit SP. OFFER for this PLU retun to weighing mode enter preset code 28 delete the special offer
0=not;1=yes return to weighing mode enter preset code 29
Print the special offer list return to weighing mode
Tara weight:
DATA ENTRY
30
_
TARE
*
TARE NUMBER
_
TARE
_
CODE
CODE
0.00 0.00 0.00
0
0.000
Enter the preset code 30
Enter the tare number (1-16).
Enter the tare weight in grams *) or put the empty recipient on the scale, then validate with the tare key T .
Press _ to affect the next tare memory.
Press the K key twice to return to the weighing mode.
*) Respect the increment (1 g, 2 g or 5 g, depending on the weighing range) create EAN code:
DATA ENTRY
_
32 create ean code
*
EAN CODE NUMBER
_
EAN 13
_
*
art.number shift
_
total price shift
_ quantity shift
_ unit price shift
_
0-1
0-6
0-8
0-2
0-3
0-2 enter preset code 32 enter EAN code number(1-8):1=for ticket and 2-8 for label select barcode type,0=EAN 8;1=EAN 13;2=ITF 25 NARROW;3=ITF
25 WIDE;4=EAN128;5=EAN 13+5;6=UPC-A
Select check sum type,0=normal;1=reverse;2=no check sum select Article number shift in barcode. select total price shift in barcode. select quantity shift in barcode. select unit price shift in barcode. select weight shift in barcode.
As you use EAN 13 code format,max.13 figures,13th figure=check digit, you must enter 12 figures. 41
(As youuse EAN 25 code format,max.18 figures,18th figure=check digit, you must enter 17 figures.
WEIGHT SHIFT
_
EAN CODE
_
KK
0-2
-------
0.00 0.00 0.00
LEGEND OF EAN INDENTIFICATION
A=article number
C=checkdigit
D=date
P=PLU code
W=group number
B=amout
Q=quantity
0-9 Figures
Example:
Figures 1-6: 0-9,W,P
Figures 7+8: C
Figures 8-12: B,Q,0-9
Figures 13: C up to 13 figures
1 figure
6 figures
6 figures
2 figures
5/6 figures
4/5 figures
12 figures
=Possible entry
=Possible entry
=Possible entry
=Possible entry
Examples:
0AAAAAAAAAA (UPC, Ten digit Item Number)
2AAAAACBBBB (UPC, 5-D Item/Price Check Digit/4-D Price)
2AAAAA0BBBB (UPC, 5-D Item/Zero Fixed/4-D Price)
2AAAAABBBBB (UPC, 5-D Item/No Price Check/5-D Price)
2AAAAACQQQQ (UPC, 5-D Item/Wgt Check Digit/4-D Wgt)
2AAAAAAQQQQ (UPC, 6-D Item/No Price Check/4-D Wgt)
2AAAAAQQQQQ (UPC, 5-D Item/No Price Check/5-D Wgt)
21AAAAABBBBB(EAN,5-D Item/5-D Price)
21AAAABBBBBB(EAN, 4-D Item/6-D Price)
21AAAAACBBBB(EAN,5-D Item/Price Check Digit/4-D Price)
21AAAACBBBBB(EAN,4-D Item/Price Check Digit/5-D Price)
21AAAAAQQQQQ(EAN,5-D Item/5-D Wgt)
21AAAACQQQQQ(EAN,4-D Item/Wgt Check Digit/5-D Wgt)
42
define ticket header:
DATA ENTRY
_
35 ticket header
*
ENTER TEXT
___
*
K
0.00 0.00 0.00 define ticket bottom:
DATA ENTRY
_
36 ticket bottom
*
ENTER TEXT
___
*
K
0.00 0.00 0.00 define runing display message:
DATA ENTRY
_
38 running message
*
ENTER TEXT
___
*
K
0.00 0.00 0.00 enter preset code 35 enter text(Max.4 lines;100 characters) return to weighing mode enter preset code 36 enter text(Max.4 lines;100 characters) return to weighing mode enter preset code 38 enter text(Max.100 characters) return to weighing mode
43
create operator:
DATA ENTRY
_
39 create operator
* operator NUMBER
_
ENTER TEXT
___
_
0
_
_
K K
0.00 0.00 0.00 operator status:
DATA ENTRY
_
48 list operator
*
K
0.00 0.00 0.00 delete operator:
DATA ENTRY
_
41 delete operator
* operator NUMBER
_
DELETE NO
_
KK
0.00 0.00 0.00
0
0-1
44 enter preset code 39 enter operator number(1-5) enter operator name(18 characters) enter password of this operator if necessory confirm password define next vendor return to weighing mode enter preset code 40 print the list enter preset code 41 enter operator number(1-5)
0=nor delete;1=delete delete next operator return to weighing mode
difine shop name:
DATA ENTRY
_
42 shop name
*
ENTER TEXT
___
*
K
0.00 0.00 0.00 define advertisement text:
DATA ENTRY
_
43 advertisement text
*
ARTICLE group
_
ENTER TEXT
___
*
KK
0.00 0.00 0.00 define date text :
DATA ENTRY
_
44 date text
* date text NUMBER
_
ENTER TEXT
___
*
K K
0.00 0.00 0.00
0
1-3 enter preset code 42 enter text(4 lines,100 characters) return to weighing mode enter preset code 43
1-10 advertise text number enter text(1 lines,60 characters) return to weighing mode enter preset code 44
0=none ;1-3 date entry enter text(18 characters) return to weighing mode
45
define date/time:
DATA ENTRY
_
45 DATE / time
* date
_ time
_
KK
0.00 0.00 0.00 define increase/decrease:
DATA ENTRY
_
46 discount
* discount nr.
_ discount name
___
* discount text
___
0
0-1
0
46 enter preset code 45 enter date (the format in [setup]-6-31 menu) enter time in format:HH-MM-SS (the format in [setup]-6-33 menu) return to weighing mode enter preset code 46 enter increase/decrease number(1-16) enter increase/decrease name enter increase/decrease text enter increase/decrease rate return to weighing mode
* percent xx%
_
K K
0.00 0.00 0.00 define pack date offset:
DATA ENTRY
_
47 pack date offset
_
K
0.00 0.00 0.00 define LOGO message:
DATA ENTRY
_
48 LOGO Message
_
K
0.00 0.00 0.00 define store LOGO:
DATA ENTRY
_
0
0
0 49 LOGO Message
_
K
0.00 0.00 0.00
0 enter preset code 47 input the pack date offset number. return to weighing mode enter preset code 48 input the message showed after “SYSTEM LOADING”, up to 16 characters. return to weighing mode enter preset code 49 enter store logo number(0-255) return to weighing mode
47
Keyboard configuration
Enter the menu【CODE】【3】【*】,display will show “KEYBOARD CONFIG”, then do following operation.
Standard configuration
【 01】【*】 display “CONFIG. NO” press key: 0＝NO，1＝YES，then press【CODE】 key, and press 【CODE】 key exit SETUP mode.
Function keys
【 02】【*】 display “KEY ST ON 0-1”
to active key “ST”, 0＝OFF (disable), 1＝ON (enable), press 【*】 key, display next option “KEY R ON 0-1”;
to active key “R”, 0＝OFF (disable), 1＝ON (enable), press 【*】 key, display next option “KEY X ON 0-1”;
to active key “X”, 0＝OFF (disable), 1＝ON (enable), press 【*】 key, display next option “KEY - ON 0-1”;
to active key “-”, 0＝OFF (disable), 1＝ON (enable), press 【*】 key, display next option “KEY + ON 0-1”;
to active key “+”, 0＝OFF (disable), 1＝ON (enable), press 【*】 key, display next option “KEY # ON 0-1”;
to active key “#”, 0＝OFF (disable), 1＝ON (enable), press 【*】 key, display next option “KEY TARE ON 0-1”;
to active key “TARE”, 0＝OFF (disable), 1＝ON (enable), press 【*】 key, display next option “KEY FIX ON 0-1”;
to active key “FIX”, 0＝OFF (disable), 1＝ON (enable), press 【*】 key, then press key 【CODE】to exit the setting mode.
Special keys
【 03】【*】 display “OPERATOR KEYS 1” input the quantity of operator, then press key 【*】, display “NO IN/DECREASE 0-1”； to select if use the DISCOUNT key, press key 0＝NO (disable)，1＝YES (enable),as select
“NO”, press key【*】, display “CONFIG NO 0-1”, then press 0（not save）/1（save）， press key 【*】to finish. As select “YES” to enable the DISCOUNT key, display “DISCOUNT
NO.”, then show “CONFIG NO 0-1”,press key 0（not save）/1（save）, press key 【*】 to finish. press key 【CODE】 to exit SETUP mode.
48
List CONFIG
Print out current keyboard config.
Operator configuration
Enter the menu【CODE】 【 *】,display will show “OPERATOR CONFIG”, then do following operation.
Standard configuration
【 01】【*】 display “CONFIG. NO”
press key 0＝NO，1＝YES，then press key 【*】. Press 【CODE】 to exit SETUP mode.
New configuration
【 02】【*】 display “SERVICE MODE 0-1” select the mode as power on: 0＝SERVICE MODE, 1＝PERPACK MODE, press key 【*】, then display next option “DATE & TIME 0-2”;
select print paper, 0＝TICKET, 1＝LABEL, 2＝LABEL+TOTAL LABEL , 3＝TOTAL LABEL , press key 【*】 , then display next option “DATE+TIME 0-2”; select display contents as idle, 0＝RUNNING MESSAGE , 1＝DATE+TIME , 2＝BOTH OFF , then press key 【*】, display next option “SCREEN SAVER 0-5”; select the idle time before displaying screen saver pictures: 0＝NO SCREEN SAVERS, 1＝
TWO MINUTES, 2=THREE MINUTES, 3=FOUR MINUTES, 4=FIVE MINUTES, 5=SIX
MINUTES, press key 【*】, then display next option “ONE SECOND 0-5”; select the interval of screen saver pictures: 0＝ONE SECOND, 1＝TWO SECONDS,
2=THREE SECONDS, 3=FOUR SECONDS, 4=FIVE SECONDS, 5=SIX SECONDS, press key
【 *】, then display next option “TARE DISPLAY 0-1”; select if show and print tare, 0＝TARE DISPLAY , 1＝NO TARE , then press key 【*】, display next option “PR. INPUT W/# 0-1”; select inputting temporary price method with # key, 0＝PR. INPUT W/# , 1＝PR.INPUT
W/O # , then press key 【*】. Press key 【CODE】 to exit SETUP mode.
List Config
Print out the OPERATOR CONFIG
49
Special function
NO. NAME
01
05
06
07
08
09
10
11
12
16
17
18
Country Finish
Unit of price
Unit price print
Print less 20e
Amount 0 Print
Plu format skip
Plu input type
Enter the menu【CODE】【6】【*】,display will show “SPECIAL FUNCTION”, then do selection as following.
If print price unit
Weight unit print
If print weight unit
Print with motion
PLU NUMBER LENGTH
OPTIONS
0=do not round；
1=round price；
2=round cut；
3=round carry；
4=round 1/4
0=as default；
1=no not round；
2=round price；
3=round cut；
4=round carry；
5=round 1/4
0= /kg；
1= /500g；
2= /100g；
3= /50g；
4= /g
0= /kg；
1= /500g；
2= /100g；
3= /50g；
4= /g
0= print on label；
1=not print
0=kg；
1=g；
0= print on label；
1=not print
0=back to 20E；
1=without motion
2=with motion
0=disable；
1=enable
0＝disable
1=enable
0=default config.；
1=customer zed
0=with [v..] key
1=press [*]then [V..]
0=no limitation
1＝enter PLU length
DESCRIPTION
Country selection
Select round price method
After discount, round price
Select the unit of unit price
Select the unit of printing on label
If print unit of unit price on label
Select weight unit for printing
If print weight unit on label
Select if print label as weight changed
6/15Kg, 20e=40g，
15/30Kg, 20e=100g
If print as amount 0
Select items in create PLU menu
Select call PLU method
50
20
21
ET LINK TO PLU
PRICE OPEN TYPE
1＝without zero prefix
0=not link to PLU
1＝link to PLU
0=depends on PLU
1=all enable
2=all disable
1=all enable
2=all disable
24
25
OPEN PRICE MARK
OPEN PRICE MODE
1=all enable
2=all disable
0=free price
1=lower price
0=temporary
1＝permanent
26
27
28
FIX WEIGHT
FIX KEY
FIX KEY IN PREPACK
29 2 ND LABEL PRINT
0=as fix weight
1=as by_cnt unit
2＝minimum weight
0=fix key active
1=fix key inactive
0=fix key active
1=fix key inactive
0=disable
1=enable
30 Select Year Length 0=YY 2 digits；
1=YYYY 4 digits
0=YYMMDD
1=DDMMYY
2=DDMMYY(CHR)
3＝MMDDYY
4=DDMMMYY(CHR)
32 DATE 0=”/”
1=”.”
2=”,”
3=”-”
1＝12 hours
PLU：XXXX，LEFT：YYYY
35 SELL BY FORMAT 0=not print today
1=print today
0=by label 36 PACK DATE FORMAT
1=by best before
2=by sell by
37 WIRELESS 0=without wireless
1＝with wireless
1＝display PLU l1
2＝scrolling PLU l1
3＝display PLU l2
4= scrolling PLU 2
Set the Extra text number the same as the PLU number
Select if all PLUs allow to change price temporary
Select if all PLUs allow to discount price
Select SPECIAL OFFER method
Price change limitation
If save the temporary price to
PLU
Select FIX WEIGHT item function
Select FIX KEY enable or disable
Select FIX KEY enable or disable in PREPACK mode
Select if print second label
Select the year format
Select date format on display and receipt (not label)
Select separator between date
Display the PLU quantity and left space
Select start date of sell by
Select if print pack date
If use wireless
Select PLU description display mode
51
40
41
42
Precious Price
IP VALID CHECK
Switch net mode
Precious Price 0.00
0=NO
1=YES
0=NO
1=YES
43
46
Display negative weight
PLU NO. Length
0=NO
1=YES
44 Change 0=Chinese
1=English
2=France
3=Turkish
4=Polish
0=6 digits
48
50
EAN 13 Style
PLU Display Font
1=8 digits
0=standard
1=special
0=Normal
1=with [*] key
0=Small font
1=Big font
Higher than this price will give a warning message when sell a by weight PLU.
If Check the last digit of IP address
As you set get PLU from network server, when the scale can’t get PLU scale will change to get from local scale
If display negative weight
Select language
Select PLU length
Select call PLU method in prepack mode
Select PLU display font size
52
Label definition
Enter the menu【CODE】【7】【*】,display will show “LABEL DEFINITION”, then enter following submenu. Example to set SERVICE BY WEIGHT label:
After press 【CODE】【7】【*】,then press 01【*】, input label number, press 【*】 key confirm.
01SERVICE BY WEIGH
02SERVICE BY COUNT
03PREPACK BY WEIGH
04PREPACK BY COUNT
05TOTAL LABEL
06COPY LABEL
07DELETE LABEL
Password setting
Enter the menu【CODE】 【 *】,display will show “PASSWORD SETTING”, then select following submenu to set.
NO. MENU
01 STANDARD CONFIG
02 MANAGER PASSWORD
03 SCALE PASSWORD
PARAMETER
MANAGER PASSWORD?
NEW PSW _ _ _ _
NEW PSW _ _ _ _
DESCRIPTION
Clear all passwords of the scale. If you have set the ADMINISTRATOR password you should input the manager password first.
Set the ADMINIDTRATOR password.
Set the power on password of scale.
04 CODE PASSWORD
05 PRICE CHANGE PSW
06 DISCOUNT PSW
NEW PSW _ _ _ _
NEW PSW _ _ _ _
NEW PSW _ _ _ _
MANAGER PASSWORD?
Set the password for entering [CODE] menu.
Set the password for changing price.
Set the password for discounting.
Clear each password one by on. If you have set the ADMINISTRATOR password you should input the manager password first.
0:NO PASSWORD
1:MANAGER PSW
2:VENDOR PSW
Set the password to exit screensaver.
53
Service function
Enter the menu【CODE】【9】【*】,display will show “SERVICE FUNCTION”, then do following operation..
NO. MENU PARAMETER DESCRIPTION
Test the scale display,keyboard etc
Test scale memory
05 CALIBRATION
09 TICKET NO. TO 0
17 DELETE ALL PLU
18 DELETE ALL GROUP
19 DEL. ALL OPERATOR
28 HEAD CLEAN ALERT
29
CHG PAPER MSG
0=no
1=yes
0＝CONFIG NO;
1=CONFIG YES
0=no
1=yes
0=no
1=yes
0=no
1=yes
0=NOT CLEAR
1=CLEAR
0=ENABLE IN PP.
1=DISABLE IN PP
0=Enable
1=disable
0=Enable
1=disable
Test scale RS232
Display increment X10
Calibrate the scale
Set the scale number
Reset the ticket number to zero.
Print out fonts table
Reset scale
Set IP address of scale
Enter update firmware state
Test printer with ticket
Test printer with label
0=DISABLE ALERT
1=ENABLE ALERT
54
34 CASH DRAW TEST
START CHAR – END CHAR
Test the cash drawer
If you use wireless scale, please configure the wireless option here
Input the Unicode range of the char you want to check.
Function test
01【*】
【*】
This function used to test the display, keyboard and printer.
Enter the function, and light on all the display to check if the display is ok.
Display 1234... testing, then scale will print out a ticket to check the printer.
At last which will test the keyboards, you should press the key one by one according to the message.
Memory test
02【*】
This function used to test scale memory.
Enter the memory test, scale will test it automatically, then print out the test report, also give some information if something is wrong.
Interface test
03【*】
This function used to test RS232 com part. Before the test you should shorten the PIN 2 and PIN 3 of the COM port.
Enter the test and scale will give you message in 5 minutes.
After the test, take out shorten wire.
High resolution display
This function used to watch the high resolution of the scale. Use it you can check the
55
loadcell and A/D pcb.
04【*】
"PUSH CAL BUTTON” Enter the menu， press the calibration button Display the high resolution. Press key【C】 to exit.
Primary configure
08【*】
(scale number)【*】
This function used to set the scale number.
Enter the menu “Primary Config”
Input scale number
Reset ticket number
09【*】
0or1
This function used to reset ticket number.
Enter the menu
Select if reset it
0：no
1：yes
【*】
Clear BRAM
12【*】
0or1
【*】
This function used to clear all the data in BRAM, including the PLU DATA, SET UP DATA etc.
Enter the menu
Select the item
0：not clear
1：clear
Fonts tabel
13【*】
This function used to list the fonts table in scale.
Enter the menu and print out the fonts list.
56
Reset scale as default
This function used to reset the scale as factory default. This will clear all programmed data and reports, but not clear the calibration data.
15【*】
0or1
_
Enter the menu
Select the item
0：not reset
1:reset
Usually we should also make sure that we made the right country selection. Go
【 CODE】6【*】01【*】
01【*】 input the Country code
【*】 Reset default 0or1 to the country finish menu.
Enter Country Finish menu
Enter Country selection e.g. 00: China; 04: Singapore.
0: not reset to country default
1: reset to country default
Clear all PLU data
17【*】
0or1
【*】
This function used to clear all PLU data in the scale.
Enter the menu
Select item
0：not clear
1：clear
Clear Group
18【*】
0or1
This function used to clear group in the scale.
Enter the menu
Select item
0：not clear
1：clear
【*】
Clear operator
19【*】
0or1
【*】
This function used to clear all the operator data of the scale.
Enter the menu
Select item
0：not clear
1：clear
57
Network configure
This function used to set IP address, net mask, server IP, and router IP etc.
21
SERVICE MODE
_
NETWORK CONFIG
*
IP ADDRESS
_
NET MASK
_
SERVICE IP
_
ROUTE IP
_
IDLE TIME
_
_
_
_
MAC ADDRESS
_
_
10
_
Enter the preset code 21.
Enter network configure
Input IP address
Input NET MASK address
Input SERVER IP address (If necessary)
Input ROUTE IP address (If necessary)
Input IDLE TIME (10 is ok)
Scale will restart automatically.
After completing setup, if necessary you can choose the PLU SOURCE. The operation as bellow:
K9* Call the menu "Technical service "
SERVICE MODE
21
_
NETWORK CONFIG
*______
PLU SOURCE
_
CODE
0.00 0.00 0.00
0-2
Enter the preset code 21.
0=Get PLU from local scale
1=Get PLU from NETWORK
2=First from network, then from local scale
Press K to exit.
58
Ticket print test
Label Printer Test
This function used to test the printer with ticket.
24【*】 Enter the preset code 24.
DISPLAY DESCRIPTION
RESIST 600-999 850 Select the Ohms Rating marked on the
Print Head.
SPEED 105 MM/S 0-5 Select the printer speed:
0=125mm/s; 1=115mm/s;
2=105mm/s; 3=95mm/s; 4=85mm/s;
5=75mm/s
ENERGY -4 -- +4 0 Enter print density (use CNT/WT CHANGE key to input negative value)
PAP.END DET. NO 0-1 Enable paper end detecting (i.e. enable the take label sensor)
0= disable; 1=enable
PRINTERTEST NO 0-1 Conduct printer test (To print out test ticket)
0= No; 1=Yes
SENSORTEST NO 0-1 Conduct gap sensor test
0= No; 1=Yes
PAPER: ⇑ ⇓
SENSOR OK OK=*
Slowly remove the ticket and insert the ticket again in 10 seconds. The test result will be shown.
This function is used to test label printer hardware and adjust printer parameters.
25【*】 Enter the preset code 25.
DISPLAY DESCRIPTION
RESIST 600-999 850 Select the Ohms Rating marked on the
Print Head.
SPEED 85 MM/S 0-5 Select the printer speed:
0=125mm/s; 1=115mm/s;
2=105mm/s; 3=95mm/s; 4=85mm/s;
5=75mm/s
ENERGY -4 -- +4 0 Enter print density (use CNT/WT CHANGE key to input negative value)
PAP.END DET. NO 0-1
REWIND NO 0-1
Enable paper end detecting (i.e. enable the take label sensor)
0= disable; 1=enable
Enable rewind feature
0= disable; 1=enable
OFFSET 35 Enter offset length in mm (Eject distance)
59
TAKEUP THRESHOLD
100
Enter the threshold of take up sensor
PRINTERTEST NO 0-1 Conduct printer test (To print out test ticket)
SENSORTEST NO 0-1
0= No; 1=Yes
Conduct gap sensor and take label sensor test
0= No; 1=Yes
LABEL POS OK=*
LABEL TEAR OK=*
SENSOR OK OK=*
Lead the label to the start position manually. The scale will test gap sensor.
The scale will test take label sensor
The scale will issue two or three labels and show the test results.
Configure RS232
26*
0or1or2or3or4or5or6
This function is used to set the COM Port parameters.
_
0or1
_
0or1or2
_
0or1
_
0or1
_
Enter the menu
Baud rate
0：300 7:38400
1：600 8:57600
2：1200 9:115200
3：2400
4：4800
5：9600
6：19200
Databits
0：5 digits
1：6 digits
2: 7 digits
3：8 digits parity
0：no
1：odd
2：even
Stop bit
0：1 digit
1：2 digits
0:Procedure;1:Procedure 7 EIN
60
Reports
05
GROUP
REPORT
【*】
Enter the menu【CODE】【2】【*】,display will show “REPORT CONFIG.”, then do following operation..
"DEFAULT YES" (press key: 0=YES,1=NO)
【*】
【*】
【*】
【*】
【*】
"TODAY "
(press key:0=today，1=last day，2＝total，3＝ all）
"SIMPLE RPT" (press key [↓]to select simple or detail report）
"NOT PRINT" (press key [↓] to select print or not print report）
【*】
【*】
【*】
【*】
"TODAY "
(press key:0=today，1=last day，2＝total，3＝ all）
"ALL PLUS" ([↓] to select the PLU range or all plu）
"FROM PLU NO.0" 【 *】 "TO PLU NO. 0"（PLU range）
"SORT BY SUM" ([↓] to sort by PLU or by total）
"NOT PRINT" (press key [↓] to select print or not print report）
【*】
【*】
【*】
"TODAY " (0=today，1=last day，2＝total，3＝all）
"NOT PRINT" ((press key [↓] to select print or not print report）
【*】
【*】
【*】
"TODAY "
"ALL GROUPS"
(0=today，1=last day，2＝total，3＝all）
([↓] to select GROUP range or all group）
61
【*】
【*】
【*】
【*】
06 GROUP H REPORT
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
62
"FROM GROUP
NO.0"
*】 "TO GROUP NO. 0"（GROUP range）
"SORT BY SUM" ([↓] to sort by PLU or by total）
"SIMPLE RPT"
"NOT PRINT"
([↓] to select detail report or simple report）
(press key [↓] to select print or not print report）
"TODAY " (0=today，1=last day，2＝total，3＝all）
"ALL GROUPS" ([↓] to select GROUP range or all group）
"FROM GROUP
NO.0"
*】 "TO GROUP NO. 0"(GROUP range）
"SORT BY SUM" ([↓] to sort by PLU or by total）
"NOT PRINT" (press key [↓] to select print or not print report）
"TODAY " (0=today，1=last day，2＝total，3＝all）
"NOT PRINT" (press key [↓] to select print or not print report）
"SETTLE $ YES" (press key [↓] to select YES or NO)
"TODAY " (0=today，1=last day，2＝total，3＝all）
"SIMPLE RPT"
"NOT PRINT"
([↓] to select detail report or simple report）
(press key [↓] to select print or not print report）
"TODAY " (0=today，1=last day，2＝total，3＝all）
"PRINT" (press key [↓] to select print or not print report）
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
12
CASHDRAW
REPORT
"TODAY " (0=today，1=last day，2＝total，3＝all）
"ALL VENDORS" ([↓] to select VENDOR range or all VENDORs）
"FROM VENDOR
NO.0"
【 *】
"TO VENDOR NO. 0" （ VENDOR range）
"SORT BY VEN" ([↓] to sort by VENDOR or by total）
"SIMPLE RPT"
"NOT PRINT"
([↓] to select detail report or simple report）
(press key [↓] to select print or not print report）
"TODAY "
"NOT PRINT"
(0=today，1=last day，2＝total，3＝all）
(press key [↓] to select print or not print report）
"NOT PRINT" (press key [↓] to select print or not print report）
"NOT PRINT" (press key [↓] to select print or not print report）
"NOT PRINT" (press key [↓] to select print or not print report）
"202 SALES RPT NO"
"203 PLU RPT
NO"
"204 PROMOTE RPT NO"
63
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
【*】
"205 GROUP RPT NO"
"206 GROUP H RPT NO"
"207 HOURLY RPT NO"
"208 SETTLE RPT NO"
"210 ST/RETN RPT NO"
"211 VENDOR RPT NO"
"212 CASHDRAW RPT NO"
"213 WEEKLY RPT NO"
"214 MONTHLY RPT NO"
"215 YEARLY RPT NO"
"NOT PRINT" (press key [↓] to select print or not print report）
"DELETE NO" (Press key:0=NO,1=YES）
PC software
【*】
【*】
PLU records and setup data of the bPro can be programmed through a PC (Personal
Computer) using the METTLER TOLEDO program bSoft and bLabel New scales can be easily set up by using this program.
Which requires an IBM or compatible PC with Windows 2000 or higher version operating system. One serial port or Ethernet port is required. The wiring diagrams shown in the following figure can be used to make cables from a 9-pin PC serial port to the 9-pin connector at the bPro. Factory cables are available from METTLER
TOLEDO using the part numbers shown in the figure.
123848OTC Cable, PC DB9 to bPro 10ft/3m
2 3
PC
DB9-F
TO 9-PIN SERIAL
RS232 PORT
3
5
2
5 bPro
DB9-F
TO 9-PIN SERIAL
RS232 PORT
64
Flashing Software
The bPro Operating System Software is retained in Flash EEPROM's on the Main
Logic PCB. The EPROM's can be reprogrammed using a PC and a downloader program Hyper terminal. Cables and components are the same as above RS232 cable.
Before downloading the software, turn the bPro power OFF. Connect one end of the cable to the PC's serial port and the other end to the bPro serial port.
Press the 【PRINT】key as power on the scale.
The scale will display “WAIT FOR HOST……” to wati for PC signal.
Then enter the Hyper terminal, to select right COMM port of the computer.
Then set the data as “baud tare 115200, data bits 8, parity none, stop bits
1,flow control none”
After come back main interface of the Hyper terminal, to select “ send file” ,select the scale code and the protocol as “1K Xmodem”. Send the file to scale.
The PC screen will display a status menu to show the flashing progress. When the flashing is completed, the scale will reset automatically. Press any key to exit
Hyper terminal program at the PC.
Also you can use a kit made of Mettler-Toledo which can update the firmware via Ethernet. First connect the Ethernet cable from scale’s RJ45 to computer.
If you use Ethernet to update, hold the [00] key to power on scale, before it you should set the scale’s IP address.
Also you should make some setting in PC kit, that will be introduced in software.
65
66
4
Troubleshooting
Troubleshooting Guide
Following is a list of symptoms that could occur, and the recommended action to correct the problem.
SCALE INOPERATIVE/BLANK DISPLAYS
1. Check AC power at outlet.
2. Check Voltage on Main Logic PCB. If voltages are zero, check Power Supply.
3. If test point voltage is good replace Main Logic PCB.
4. Check Display Cable on Main Logic PCB and Operator Display PCB. Check
Display PCB.
KEYBOARD INOPERATIVE a) b) c)
1. Check keyboard connection on keyboard controller PCB.
2. Check Keyboard controller connection to Main Logic,
ensure all connections are secure.
3. If all connections are secure and keyboard is inoperative:
Replace keyboard controller PCB.
Check keyboard once again.
If Keyboard is still inoperative, replace keyboard.
SCALE WON'T ZERO (DISPLAY "PUT PLATTER ON" or "ZERO NOT CAPTURE")
1. Check platter and spider for obstructions. Turn power off, then back on.
2. Recalibrate.
3. Check Load Cell supply voltage.
4. Replace Load Cell.
LOSING PROGRAMMED DATA
1. Check Error Report of Service Mode.
2. Check Main Logic voltage at test points.
3. Replace Main Logic PCB.
PRINTER WON'T DELIVER LABEL
1. Check printer for obstructions.
2. Check if there is a label which has not been removed.
3. Check Take Label sensor obstructions.
4. Clean Take Label sensor.
5. Test Take label sensor with SENSOR TEST in Service Mode.
6. Check harness from Printer to Main PCB.
7. Check label stepper motor.
8. Replace Main Logic PCB.
INCORRECTLY INDEXES LABELS
1. Check label installation.
2. Check label format and label size.
3. Clean Gap Sensor Lens.
4. Check and clean platen roller, stripper bar, and delivery path using MT cleaning pen.
5. Adjust label Gap Sensor through SENSOR TEST in Service Mode.
6. Replace Gap Sensor Assembly.
7. Replace Main Logic PCB.
LABELS DARK
1. If labels are printed correctly, but are excessively dark, check the ENERGY setting in
Service Mode.
2. Check printhead harnesses for loose wires.
LABELS MISSING DOTS
1. If the labels are streaked by lines from top to bottom, replace the
Printhead.
2. If characters are cut off, check label format programming. If OK, replace printhead.
LABELS ARE EXCESSIVELY LIGHT/DARK
1. Check Print SPEED and ENERGY setting in Service Mode.
2. Check with other known good label stock.
3. If light print, check and clean printhead resistor line and platen roller.
4. Check printhead harness for loose wires.
5. Check Main Logic PCB voltages. If OK, replace Printhead.
LABEL PRINT IS MOTTLED WITH LIGHT SPOTS
1. Check with other known good label stock.
2. Check and clean printhead resistor line and platen.
3. Replace printhead.
LABELS NOT STRIPPING CORRECTLY
1. Check with other known good label stock, e.g. Nashua.
2. Check label format programming.
3. Check rewind spool for wear.
4. Check Gap Sensor and Take Label Sensor with SENSOR TEST in Service Mode.
LABELS PRINTED EVEN IF ONE IS NOT YET TAKEN
1. Check PAP. END DET. option in Service Mode (Paper End Detection)
2. Check Take Label Sensor.
3. Check Main Logic PCB.
OUT OF LABELS ERROR
1. Make sure labels are threaded through the Gap Sensor.
2. Clean/Check Gap Sensor.
3. Check Gap Sensor through SENSOR TEST in Service mode.
4. Replace Gap Sensor.
5. Replace Main Logic PCB.
CAN'T COMMUNICATE WITH PC
1. Test scale serial port through INTERFACE TEST in Service Mode.
2. Check the connection cable.
3. Check which serial port is used at PC.
4. If using bSoft, check the COM PORT SETUP and set to the following parameters:
Data bits: 8
Parity: None
Stop bits: 1
67
68
POWER SUPPLY
Flow control: None
Following is a list of symptoms that could occur, and the recommended action to correct the problem.
Place the Power Switch to the OFF position. Remove the platter, spider, and top cove.
To check the +24VDC output voltage from the Power Supply terminal between the terminals marked +V and GND, the acceptable output range is +24VDC +/-0.50 VDC.
If the voltage is normal, the Power Supply should be good, and the problem should be suspected as being in the Main Logic PCB or a component that connects to the Main
Logic PCB.
If the output voltage is zero, check the 120 VAC input voltage. If the correct AC input voltage is present, but there is no +24 VDC output, replace the Power Supply.
If no voltage is present, check the fuse (240VAC 4A) on the power supply. If the fuse is OK, check AC input at the Line Cord Jack between the Red wire and Black wire. If the 120VAC is present, suspect a defective power switch. If 120 VAC is not present at the jack, check the fuse (240VAC 3A) installed in the Line Cord Jack, as shown in the following Figure. If the fuse is OK, verify voltage is present at the AC wall outlet. working fuse backup fuse
Main Logic PCB
The Main Logic PCB receives +24VDC from the Power Supply and uses this to supply +10VDC and +5VDC to other components. The Main Logic PCB controls all functions in the unit including the thermal printer. Inputs and Outputs to the
Main Logic include the Label Taken Sensor, Gap Sensor, Printhead, Stepper
Motor, Rewind Motor, Load Cell and etc. The following Figure shows the locations of the various components and connectors on the Main Logic PCB.
If the volages are not within the range specified, and the Power Supply voltage is correct, replace the Main Logic PCB.
NOTE: WHEN REPLACING THE MAIN LOGIC PCB, THE UNIT MUST BE
REFLASHED.
69
70
Load Cell
The Load Cell can be tested for proper analog voltage input and millivolt output by measuring the voltage on the Main Logic PCB. To check the input voltage across +EXC & -EXC, place your meter on volts and put the positive lead on the left pin of F1 and the negative lead on the left pin of F4. You should be reading a steady +10VDC +/- 0.25VDC.
If the Excitation voltage is good, the signal output can be checked across +SIG &
-SIG. Set the meter to read in millivolts (mV). Put the positive lead on the left pin of F2 and negative lead on the left pin of F3. With no weight on the platter, you should read zero data. As you add weight to the platter, the voltage should rise and be linear if equal weight is added each time. If the output is linear and correct, but no weight is displayed, replace the Main Logic PCB. If there is no output from the load cell, but correct input voltage, replace the load cell.
Warning Message
INPUT TOO BIG
The input is too big.
INPUT TOO SMALL
The input is too small.
TOO MUCH INPUT
The input is out of limit.
WRONG CODENR.
The code number is invalid.
KEY NO FUNCTION
The key has no function.
KEY BLOCKED
The key is disabled. Check the KEYBOARD CONFIGURE.
PLU NOT FOUND
The entered PLU number does not exist.
AG NOT FOUND
71
72
The entered Group number does not exist.
OPER.NOT FOUND
The entered Operator number does not exist.
LABEL NOT FOUND
The entered Label Format does not exist.
PLUNR IS OCCUP
You are trying to duplicate a PLU into an exist PLU number.
LABELNR. OCCUP
You are trying to duplicate a label format into an exist label format number.
AG NOT DELETABLE
This Group contains total data and can not be deleted.
OP NOT DELETABLE
This Operator contains total data and can not be deleted.
MEMORY FULL
Memory is full.
WEIGH AGAIN
You are trying to record one item twice. Remove the item from the platter and put a new item on the platter.
WRONG LABEL
The installed label roll does not match the configured label format.
LABEL MOVED
The stepper motor or the rewind motor is not working properly.
CHANGE PAPERROLL
The label roll is not installed or the label roll is empty.
TAKE LABEL OFF
Take off the current label before printing the next one.
NO FREE OX KEY
All the configured operator keys have been occupied.
PRINT TICKET
Print out the customer ticket before logging out.
OPEN CUST. TICK
You are trying to delete an operator who has total data.
OX NOT LOGGED-IN
The operator has not be assigned to an operator.
PAYMENT TOO LOW
The payment is less than the total amount.
NO FURTHER REG.
Error Message
No further transaction has been recorded.
DISCOUNT IMPOSS
This PLU does not allow to be discounted. Check the PLU Discount configuration, or this PLU is in special offer.
TARE TOO BIG
The entered tare is too big.
PLU TARE ACTIVE
You are forbidden to override the PLU tare.
NO STABLE WEIGHT
The weight is not stable.
PUT PLATTER ON
The weight is too small and out of power up zero range.
ZERO NOT CAPTURE
The weight is too big and out of power up zero range.
WEIGHT TOO SMALL
The weight is too small to be printed.
ERROR TAKE-SENS
The take label sensor is not working properly.
ERROR POS_SENS
The gap sensor is not working properly.
ERROR INTERFACE
The serial port is not working properly.
Listed below are the possible error codes. When an error code appears, the scale should be switched off and on. In many cases the error will disappear.
There are 3 different kinds of error messages:
Error Status 1:
Warning! After the warning the scale can still be used.
Error Status 2:
Press "CODE" key. Change to one of the CODE menu. Back to normal operation mode.
Error Status 3:
Press "CODE" key and enter SERVICE MODE, after returning to normal operation mode the scale will perform RESET.
73
Error Message
ERROR 300 PRINTER
ERROR 301 PRINTER
ERROR 307 PRINTER
ERROR 308 PRINTER
ERROR 310 PRINTER
ERROR 101 AP
ERROR 400 CELL
ERROR 401 CELL
ERROR 200 DATABASE
ERROR 201 XX DATABASE
ERROR 202 XX DATABASE
ERROR 203 YY DATABASE
ERROR 205 DATABASE
Reason
Printer driver defect
Printer driver defect
Printhead defect
Printer driver defect
Printer driver defect
Real Time Clock defect
Load Cell defect
Load Cell defect
Data bank error
XX Data error
XX Data error
YY Data error
Data bank error
2
1
Status Action
2
2
2
1
Replace Main Logic PCB
1 Reflash the software
2 Replace Main Logic PCB
1 Replace printhead
2 Replace printhead harness
3 Replace Main Logic PCB
Replace Main Logic PCB
-
Replace Main Logic PCB
Replace Main Logic PCB
1 Replace Main Logic PCB
2 Replace Load Cell
-
3
2
2
2
3
1 Recalibrate
2 Replace Main Logic PCB
3 Replace Load Cell
Reset RAM
1 Reset RAM
2 Delete Data XX
1 Reset RAM
2 Delete Data XX
1 Reset RAM
2 Configure Y Y
Reset RAM
Meaning of XX
02 Ticket data
07 data
13 Label data
03 Time total data
04 Text data
15 Date text data
21 PLU label data
Tare PLU
Meaning of YY
01 Operator Configure
03 Keyboard Configure
04 Password Configure
74
Interconnecting Diagram
75
5
Parts Replacement
Replace main PCB
!
all the data saved in main PCB, as you change the main PCB you will lose all of them.
Counter type
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Screw out the 5 bolts (A) from base and take away.
• Show main PCB.
• Pull out all connection from main PCB.
• Screw out 6 bolts (B) from main PCB, take away it.
Install main PCB
• Put the main PCB to right position, screw in 6 bolts of main PCB.
• Put the cover of base then screw in 5 bolts.
76
• Put on platter.
• Power on scale.
Hanging type:
bPro -H2
A3
B3
Take out main PCB
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Screw out the 2 bolts (A3) from scale and take away.
• Screw out 4 bolts (B3) from scale and show main PCB.
• Pull out all connection from main PCB.
• Screw out 4 bolts (C3) from main PCB, take away it.
Install main PCB
• Put the main PCB to right position, screw in 4 bolts of main PCB.
• Connect all harness to main PCB.
• Put the display and power support kit to position, screw in 4 bolts.
C3
77
• Put the cover of display then screw in 2 bolts.
• Install whole hanging scale.
• Put on platter.
• Power on scale.
Replace switch power
Counter type:
Take out switch power
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Screw out the 5 bolts (A) from base and take away.
• Pull out the harness in switch power.
• Screw out 4 bolts in the power PCB.
• Take away the switch power.
Install switch power
78
• Put the switch power to the right position.
• Screw in 4 bolts of the power PCB.
• Plug in all the connection harness in the PCB.
• Put the cover of base then screw in 5 bolts.
• Put on platter.
• Power on scale.Hanging type:
bPro -H2
D3
E3
Take out switch power
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Take away the back display cover and back display kit as before.
• Screw out the 2 bolts (D3) from base and take away.
• Show the switch power.
• Pull out the harness in switch power.
• Screw out 4 bolts (E3) in the power PCB.
• Take away the switch power.
Install switch power
• Put the switch power to the right position.
• Screw in 4 bolts of the power PCB.
• Plug in all the connection harness in the PCB.
• Put the support plate then screw in 2 bolts.
• Install back display kit.
• Install whole hanging scale.
• Put on platter.
• Power on scale.
79
Replace display
Counter type
Take out display
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Take away the tower kits.
• Screw out 2 bolts in the display cover, and take out the front cover, show the display.
• Screw 5 bolts of the front display, pull out harness and take away the display.
• Screw 4 bolts of back display and pull out harness, take away back display.
Install display
• Put the back display to right position and screw in 4 bolts to fix it.
• Plug in harness of display.
• Also the harness to front display.
• Put on the front display.
• Screw in bolts for installation.
• Put the front display.
• Screw in 2 fix bolts of cover.
80
• Install the tower to base.
• Put on platter.
• Power on scale.
Hanging type:
bPro -H2
F3
Take out display
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Take out back display kit as previous method.
• Take away display harness in display.
• Screw out 4 bolts (F3) in the display support plate, and take out the back display.
• For front display, you should also take away the main PCB and power PCB, then to show the front display, screw out 4 installation bolts.
Install display
• Put the back display to right position and screw in 4 bolts to fix it.
• Plug in harness of display.
• Install the back display kit.
• Install back display cover.
• Install whole hanging scale.
• Put on platter.
• Power on scale.
81
Replace load cell
Counter type
82
Take out loadcell
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Screw out 2 bolts for fix the cover of print paper (D).
• Take out the cover (E).
• Screw out 2 bolts in interface PCB (F).
• Screw out 4 bolts in up spider, and take out it.
• Open the sealing screw (G).
• Take away up cover.
• Pull out loadcell harness from main PCB.（see above to find the main PCB）
• Screw 2 screws in loadcell and take out spacer.
• Also take out loadcell spacer.
• Also screw 2 screws for installing loadcell under the scale.
• Take away loadcell.
Install loadcell
• Put the loadcell to right position.
• Install 2 screws from scale bottom.
83
• Screw down with moment spanner.15kg CAPACITY with 8 NM,
30kg CAPACITY with 10 NM.
• Put the spacer and then screw down 2 screws in it.
• Screw down with moment spanner.15kg CAPACITY with 8 NM,
30kg CAPACITY with 10 NM.
• With X mm ruler to adjust the limit size of back 2 screws. With Y mm ruler to adjust the limit size of front 2 screws inspacer.(capacity:6/15kg X=1.2mmY=0.9mm；capacity:15/30kg X=1.9mmY=1.3mm)
• Insert the loadcell harness to main PCB.
• Install the up cover, print paper cover,up spacer,screws in interface PCB, cover of main PCB at bottom etc.
• Adjust 4 screws in up spacer and let the spacer levelly.
• Put on platter.
• Power on scale.
Hanging type:
bPro-H2
G3
H3
I3
J3
Take out loadcell
84
K3
L3
M3
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Screw out 2 bolts (G3) for fix the left cover.
• Take out the cover.
• Screw out 2 bolts (H3) in base.
• Take away A/D convertor kit (I3).
• Screw out 2 bolts (J3),take out the cover.
• Screw out bolt (K3) and bolt (L3) for connecting load cell.
• Screw out 2 bolts (M3).
• Take out loadcell.
Install loadcell
• Put the loadcell to right position.
• Use reverse steps to install the load cell as previous take out steps.
85
Replace keyboard
Counter type
Take out keyboard
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Screw out 3 bolts (H) in keyboard at bottom.
• Take out keyboard and cover kits.
• Pull out the harness of keyboard from the keyboard convert PCB.
• Rip off the keyboard overlay, take out it.
Install keyboard
• Clean the keyboard cover with alcohol, and wait it till dry.
• Let harness through the hole in it and rip off the protect paper in keyboard, then stick it to the keyboard cover.
• Plug in the harness to keyboard convert PCB.
• Put the keyboard to right position and install 3 bolts in it.
86
• Put on platter.
• Power on scale.
Hanging type: bPro-H2
Just use new one replace old one and hang it.
87
Replace printer
Counter type
I
88
Take out printer
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Screw out 2 bolts (I) at the bottom of the scale.
• Open the printer door.
• Pull out printer, also disconnect the harness in printer PCB and connect ground wire.
• Take out printer, also with sliding feet under it.
Install printer
• Put the sliding base to right position.
• Insert the harness of the printer PCB and connect the ground wire.
• Put the printer to right position and insert to scale carefully.
• Insert the sliding feet under the printer. Screw down 2 bolts for fixing the printer at bottom of scale.
• Close printer door.
• Put on platter.
• Power on scale.
89
Hanging type:
N3
bPro-H2
Take out printer
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Open right door of scale.
• Screw out 3 bolts (N3) at the bottom of the printer.
• Take out all harness in printer PCB.
• Take out printer.
Install printer
• Insert the harness of the printer PCB.
• Put the printer to right position and insert to scale carefully.
• Screw down 3 bolts for fixing the printer.
• Close printer door.
• Install whole hanging scale.
• Put on platter.
• Power on scale.
90
Replace printer head
J
!
DON’T GRIDE THE PRINTER HEAD.
Take out printer head.
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Open printer door, pull out printer.
• Screw out 2 screws (J) for fixing printer head.
• Pull out the harness from printer head.
• Take away printer head.
Install printer head
• Insert the printer head harness.
• Put the printer head and spacer to right position. Screw down 2 bolts.
• Close the printer head.
• Push the printer back to scale.
• Put on platter.
• Power on scale.
91
Install Wireless card
Counter type
! Steps as below. (counter type as example)
(A1)
(D1)
(G1)
(B1)
(E1)
(H1)
92
(C1)
(F1)
(I1)
(J1)
(M1)
(K1)
(N1)
(P1)
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Screw out bolts from up spider (C1) and screw out sealing bolts (D1).
(O1)
(L1)
• Take apart the main PCB cover in bottom (F1), also take apart the cover of scale as screw out the bolts in the bottom of scale.
93
• Put the wireless kit (A1) to the position (G1).
• Install the bolts to it (H1).
• Take out the seal from hole (I1).
• Put the Ethernet harness through the hole (J1).
• Connect the Ethernet harness to the Ethernet port (K) and fix the harness as picture (L1).
• Put the wireless card power harness through the hole (M1).
• Connect the wireless card power harness to the main PCB (O1).
• Then to install the scale cover, the up spider, the main PCB cover in bottom, seal switch bolts etc.
94
Install the memory extension board
D2
A2
E2
B2
C2
95
Install the memory extension board.
• Power off and take out the power cable from electrical outlet.
• Take away platter.
• Screw out bolts from up spider and screw out sealing bolts in scale.
• Get the memory extension board (A2)
• Find socket of extension memory in main PCB (B2).
• Install bolts (C2) to main PCB.
• Insert the memory extension board to it as (E2).
• Fix three install bolts (D2) to main PCB.
• Then to install the scale cover, the up spider, the main PCB cover in bottom, seal switch bolts etc to resume the scale.
96
6
Maintenance
External Cleaning
Cleaning Printhead
Turn the scale power off by placing the power switch to the OFF position (Press the "0" on the power switch). Disconnect power cord from outlet.
Use a soft clean cloth dampened with a mild detergent and water (or a mild cleaner) to wipe the exterior surfaces. Do not spray liquid directly on the unit. A mild spray cleaner can be used by spraying the cleaning cloth.
CLEAN PRINTHEAD USING METTLER TOLEDO LIQUID CLEANER OR
EQUIVALENT OR THE METTLER TOLEDO CLEAN PEN.
DO NOT SCRAPE THE PRINTHEAD WITH ANY OBJECT TO REMOVE GLUE OR
LABEL DEBRIS OR SEVERE DAMAGE MAY RESULT.
Turn the scale off by placing the power switch to the OFF position.
Disconnect power cord from outlet.
Open the plastic door on the right side of the scale.
Slide out the printer.
Press the trigger to open the print head.
Clean the print head with a soft clean cloth soaked in isopropyl alcohol,
METTLER TOLEDO liquid cleaner or equivalent, or the METTLER
TOLEDO Cleaning Pen.
Push back the print head until it clicks.
97
Rezeroing
Slide the printer in.
Close the plastic door.
This scale is equipped with an automatic zeroing device, which compensates for small weight change. This device is not activated when a package tare is compensated. After cleaning the dirt from the platter with the scale on, the display can read :
• a negative value
• or "_ _ _ _ _" segments can be lit.
Solution :
Press the ZERO key
If the message appears again :
Turn the scale off and back on again with the main power switch.
98
7
GEO Settings
The values for gravity adjustment are a series of two digit numbers in the range 0 to 31, as shown in the table below.
Geo. Value Table
North or south latitude in degrees and minutes
0 0
5 0
0’ - 5
46’ - 9 0
0
9 0
12
15
17
19
20
22
23
25
26
28
29
30
31
33
34
35
36
37
38
40
41
42
43
44
45
46
47
48
50
51
52
53
54
55
57
58
59
60
62
63
64
66
67
69
71
73
75
77
80
85
0
0
0
0
0
0
52’ - 12
0 44’ - 15
0
0
46’
52’
44’
6’
6’ - 17
0 10’ - 19
0 2’ - 20
0
0
0
45’ - 22
22’ - 23
0 54’ - 25
21’ - 26
45’ - 28
6’ - 29
0 25’ - 30
0 41’ - 31
0
0
0
0
0
0
0
10’
2’
45’
22’
54’
21’
45’
6’
25’
41’
0 56’
0 56’ - 33
0 31’ - 36
0 9’
0 9’ - 34
0 21’ - 35 0
0 21’
31’
0 41’ - 37
0 41’
0 50’ - 38
0 58’ - 40
0 50’
0 58’
0 5’ - 41
0 12’ - 42
0 5’
0
0 19’ - 43
0 26’ - 44
0
12’
19’
0 26’
0 32’ - 45
0 32’
0 38’ - 46
0 38’
0 45’ - 47
0 51’ - 48
0 45’
0 51’
0 58’ - 50
0 58’
0 6’
0 13’ 0 6’ - 51
0
0
13’ - 52
22’ - 53
0 22’
0 31’ - 54
0 31’
0 41’ - 55
0 41’
0 52’ - 57
0 17’ - 59
0 32’ - 60
0 52’
0 4’
0 4’ - 58 0 17’
0 32’
0 49’ - 62
0 30’ - 64
0 55’ - 66
0 49’
0 9’
0 9’ - 63 0 30’
0 55’
0 24’ - 67
0 57’ - 69
0 24’
0 57’
0 35’ - 71
0 35’
0 21’ - 73
0 21’
0 16’ - 75
0 16’
0 24’ - 77
0 24’
0
0 56’ - 85
0
52’ - 80
45’ - 90
0 52’
0 56’
0 45’
0 0’
0
325
325
650
650
975
2130
3200
18
18
19
19
16
16
17
17
14
14
15
15
12
12
13
13
10
10
11
11
9
9
8
8
7
7
6
6
5
5
4
4
26
26
27
27
24
24
25
25
28
28
29
29
30
22
22
23
23
20
20
21
21
0
1060
17
17
18
18
19
19
20
20
13
13
14
14
15
15
16
16
10
10
9
9
11
11
12
12
8
8
7
7
6
6
5
5
25
25
26
26
27
27
28
28
29
29
30
30
31
21
21
22
22
23
23
24
24
1060
2130
16
17
17
18
18
19
19
20
12
13
13
14
14
15
15
16
9
10
8
9
10
11
11
12
7
8
6
7
5
6
4
5
24
25
25
26
26
27
27
28
28
29
29
30
30
20
21
21
22
22
23
23
24
975
1300
Height above sea level in meters
1300
1625
1625
1950
1950
2275
3200
4260
Height above sea level in feet
4260
5330
5330
6400
6400
7460
17
18
18
19
15
16
16
17
13
14
14
15
11
12
12
13
9
10
10
11
8
9
7
8
6
7
5
6
4
5
3
4
25
26
26
27
23
24
24
25
27
28
28
29
29
21
22
22
23
19
20
20
21
17
17
18
18
15
15
16
16
13
13
14
14
11
11
12
12
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
25
25
26
26
23
23
24
24
27
27
28
28
29
21
21
22
22
19
19
20
20
16
17
17
18
14
15
15
16
12
13
13
14
10
11
11
12
9
10
8
9
7
8
6
7
5
6
4
5
3
4
2
3
24
25
25
26
22
23
23
24
26
27
27
28
28
20
21
21
22
18
19
19
20
16
16
17
17
14
14
15
15
12
12
13
13
10
10
11
11
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
24
24
25
25
22
22
23
23
26
26
27
27
28
20
20
21
21
18
18
19
19
2275
2600
7460
8530
13
14
14
15
15
16
16
17
9
10
10
11
11
12
12
13
7
8
8
9
6
7
5
6
4
5
3
4
2
3
1
2
21
22
22
23
23
24
24
25
25
26
26
27
27
17
18
18
19
19
20
20
21
2600
2925
8530
9600
13
13
14
14
15
15
16
16
9
9
10
10
11
11
12
12
7
7
8
8
6
6
5
5
4
4
3
3
2
2
1
1
21
21
22
22
23
23
24
24
25
25
26
26
27
17
17
18
18
19
19
20
20
2925
3250
9600
10660
14
15
15
16
12
13
13
14
10
11
11
12
9
10
8
9
7
8
6
7
5
6
4
5
3
4
2
3
1
2
0
1
22
23
23
24
20
21
21
22
24
25
25
26
26
18
19
19
20
16
17
17
18
3250
3575
10660
11730
14
14
15
15
12
12
13
13
10
10
11
11
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
0
0
22
22
23
23
20
20
21
21
24
24
25
25
26
18
18
19
19
16
16
17
17
99
8
Replacement Parts
72188012 bPro-C2
72188012 bPro-C2
Item P/N
1 180952
Description
上盖活动盖板 Label Roll Housing
2
3
183021
102326
秤盘组件 Platter
水泡 Leveling Bubble
100
Qty
1
1
1
4
5
6
7
124041 中心橡胶垫 Cap,Spider,,Center
154555 角垫 Cap,Spider,,Corner
180974 托 架 Spider
180943 上盖 Main Housing
8 174032 A/D 板 PCB Assembly,AD board
9(1) 72193829 键盘，透明硅胶按压层,bPro,C2 Keyboard,Touch pad,Silicon,bPro C2
1
1
9(2) 72209741 键盘，编程面板,bPro-C2,英文 Keyboard, Programming layer,bPro C2 ENG 1
9(3) 72193807 键盘，操作面板,bPro-C2,英文 Keyboard, Operation layer,bPro C2 ENG 1
1
4
1
1
9(4) 72193827 键盘，白色橡胶触点层,bPro,C2 Keyboard, Rubber button padding,bPro C2 1
9(5) 72193825 键盘，银浆电路层,bPro,C2 Keyboard, Membrane layer,bPro C2 1
10 72188155 键盘盖 C Keyboard Housing ,compact,top cover
11 173476 键盘转接板 PCB Assembly,keyboard convert
12 182976 调节支撑板 A Sheet Metal,Keyboard Swivel A
13 183450 支撑轴 Swivel Crutch shaft
14 180951 开关固定板 Sheet Metal,support ,Power Switch
15 72187455 电源线束 Harness,AC Power Socket
16 72187456 开关 Harness,AC power Switch
17 173307 接口板 PCB Assembly ,interface
18 167391 秤脚,秤体左侧长秤脚,bC/bPro FOOT,Long,left
19 72186444 接口固定板 Sheet Metal,Support,interface
20 72186386 开关电源 24v,2.7A Switching Power Supply,24v,2.7A
1
1
1
1
1
1
1
2
2
1
1
72186387 开关电源 24v,4.2A Switching Power Supply,24v,4.2A
21 169795 主板 PCB Assembly ,Main board,standard
72186557 主板 PCB Assembly ,Main board,Premium
22 183358 基座盖板 Sheet Metal,base cover
23 183359 键盘调节杆 Swivel adjustment support
24 180948 键盘座 Keyboard Housing,Base
25 150652 弹簧 Spring,keyboard Swivel
26 182877 调节支撑板 B Sheet Metal,keyboard swivel B
27 183452 固定轴 Swivel fixed Shaft
28 180973 基座 Aluminum Base Casting
29 72188140 秤脚,秤体右侧短秤脚 Foot,short,right
30 173596 直流线束 Harness,DC Power
31 180947 打印机侧门 Door
32 72191431 打印机组件 Printer Assembly,2" ticket
72191432 打印机组件 Printer Assembly,2" Label
33 182872 立杆固定座 Sheet Metal,support,Tower to base
34 72184997 AMI-22 传感器 Loadcell Assembly,AMI-22 for 6/15kg
72184996 AMI-40 传感器 Loadcell Assembly,AMI-40 for 15/30kg
72186985 AMI-11 传感器 Loadcell Assembly,AMI-11 for 3/6kg
72186878 AMI-40 传感器 Loadcell Assembly,AMI-40 for 30kg 6000e
1
1
1
1
2
1
1
1
1
1
2
1
2
1
1
1
1
1
2
1
101
72186875 AMI-40 传感器 Loadcell Assembly,AMI-22 for 12kg 6000e
35 72186402 导轨座 Printer Rail
36 72185419 垫 块 Loadcell spacer
37 72185423 钣金托架 Spider support
38 72188157 短盖板 B Plastic cover B,Front,Compact,bC/bPro-C2
39 72188192 立杆 C Tower, Compact,bC/bPro-C2
40 72188156 短盖板 A Plastic cover A,Rear,Compact,bC/bPro-C2
41 180946 压 板 B Sheet Metal,support B,Display
42 180954 显示盖锁紧件 Sheet Metal,support, disp to Tower
43 180945 压 板 A Sheet Metal,support A,display
44 155637 显示屏 Display Assembly,segment,CHN
72189191 显示屏 Display Assembly,segment,EURO
170120 显示屏 Display Assembly,segment,ENG
72202239 显示屏 Display Assembly,240X240
45 180944 显示外壳 Display Housing
46 72189327 滤光片 Display lens,CHN
183449 滤光片 Display lens,English
72193760 滤光片 Display lens,Euro,bc
47 156439 立杆线束 Harness,Customer display,
48 173248 线束，打印－主板 Harness,Main pcb to printer board
49 72187458 线束，接口－主板 Harness,Main pcb to interface
50 182252 键盘线束 Harness,Main PCB to keyboard
51 171790 显示转接线束 Harness,Segment Disp. convert
173345 显示转接线束 Harness,240x240 Disp. convert
52 72193070 显示盖板 Display Lens.Opaque,customer,bc/bpro-C2
53 72188193 显示滤光片 Display Lens.Compact,operator,bc/bpro-C2
54 122206 铅封纸 Sealing Sticker,EU,bC/bPro
55 72192054 铅封盖板 Sealing Cover,EU,bC/bPro
56 72224370 塑料线卡 Clip
57 72209420 小滑块 Slide space
58 72209419 导滑垫板 Slide base
B1 72204992 螺钉 M4X12，GB818-85 SCREW M4X12
B2 119054 铅封头 SEALING HEAD
B3 118549 铅封螺钉 SEALING SCREW
B4 72189609 螺钉 M4X8，GB818-85 SCREW M4X8
B5 72201470 带齿垫螺钉 M4X5 SCREW M4X5
B6 72201473 螺钉，M6X20,GB70-85 SCREW M6X20
B7 72192905 紧定螺钉，M5X16,GB79-85 SLOT SCREW
B8 72194324 螺母，M4 NUT M4
B9 72201474 自攻螺钉，M2.9X6.5,GB845 SCREW
B10 72201466 螺钉，M3X6,GB818 SCREW
102
2
1
1
1
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
21
4
4
2
9
1
2
15
6
18
1
1
1
1
1
1
1
1
1
1
B11 102661 弹簧垫圈 SPRING WASHERS
B12 72201469 螺钉，M4X14,GB819 SCREW
B13 142884 紧定螺钉，M3X8,GB79-85 SLOT SCREW
B14 143133 螺钉，M3X6,GB819 SCREW
72186380 bPro-T2
4
3
2
2
72186380 bPro-T2
Item P/N Description
1 180952 上盖活动盖板 Label Roll Housing
103
Qty
1
2 183021 秤盘组件 Platter
3 102326 水泡 Leveling Bubble
4 124041 中心橡胶垫 Cap Spider center
5 154555 角垫 Cap Spider Corner
6 180974 托 架 Spider
7 180943 上盖 Main Housing
8 174032 A/D 板 PCB Assembly,AD board
9(1) 72193830 键盘 透明硅胶按压层 bPro-T2 Keyboard,Touch pad,Silicon,bPro T2
9(2) 72193808 键盘 操作面板 bPro-T2 英文 Keyboard, Operation layer,bPro T2 ENG 1
9(3) 72193815 键盘 编程面板 bPro-T2 英文 Keyboard, Programming layer,bPro T2 ENG 1
1
1
1
4
1
1
1
1
9(4) 72193830 键盘 白色橡胶触点层 bPro-T2 Keyboard, Rubber button padding,bPro T2 1
9(5) 72193826 键盘 银浆电路层 bPro-T2 Keyboard, Membrane layer,bPro T2 1
10 180949 键盘盖 Keyboard Housing ,tower,top cover
11 173476 键盘转接板 PCB Assembly,keyboard convert
1
1
12 182976 调节支撑板 A Sheet Metal,Keyboard Swivel A
13 183450 支撑轴 Swivel Crutch shaft
14 180951 开关固定 Sheet Metal,support ,Power Switch
15 72187455 电源线束 Harness,AC Power Socket
1
2
1
1
16 72187456 开关 Harness,AC power Switch
17 173307 接口板 PCB Assembly ,interface
18 167391 秤脚 FOOT,Long,left
1
1
2
19 72186444 接口固定板 Sheet Metal,Support,interface
20 72186386 开关电源 24v,2.7A Switching Power Supply,24v,2.7A
72186387 开关电源 24v,4.2A Switching Power Supply,24v,4.2A
21 169795 主板 PCB Assembly ,Main board,standard
72186557 主板 PCB Assembly ,Main board,Premium
22 183358 基座盖板 Sheet Metal,base cover
23 183359 键盘调节杆 Swivel adjustment support
24 180948 键盘座 Keyboard Housing,Base
25 150652 弹簧 Spring,keyboard Swivel
26 182877 调节支撑板 B Sheet Metal,keyboard swivel B
27 183452 固定轴 Swivel fixed Shaft
28 180973 基座 Aluminum Base Casting
29 72188140 秤 脚 Foot,short,right
30 180975 导轨 Printer Rail Slider
31 173596 直流线束 Harness,DC Power
32 180947 打印机侧门 Door
33 72186193 打印机组件 Printer Assembly,2" Label
34 182872 立杆固定座 Sheet Metal,support,Tower to base
35 72184997 AMI-22 传感器 Loadcell Assembly,AMI-22 for 6/15kg
72184996 AMI-40 传感器 Loadcell Assembly,AMI-40 for 15/30kg
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
2
1
104
72186985 AMI-11 传感器 Loadcell Assembly,AMI-11 for 3/6kg
72186878 AMI-40 传感器 Loadcell Assembly,AMI-40 for 30kg 6000e
72186875 AMI-40 传感器 Loadcell Assembly,AMI-22 for 12kg 6000e
36 72186402 导轨座 Printer Rail
37 72185419 垫 块 Loadcell spacer
38 72185423 钣金托架 Spider support
39 182874 立杆盖板 B Plastic cover B,Front,Tower,bC/bPro-T2
40 180976 立杆 Tower,bC/bPro-T2
41 180873 立杆盖板 A Plastic cover A,Rear,Tower,bC/bPro-T2
42 180946 压 板 B Sheet Metal,support B,Display
43 180954 显示盖锁紧件 Sheet Metal,support, disp to Tower
44 180945 压 板 A Sheet Metal,support A,display
45 155637 显示屏 Display Assembly,segment,CHN
72189191 显示屏 Display Assembly,segment,EURO
170120 显示屏 Display Assembly,segment,ENG
72202239 显示屏 Display Assembly,240X240
46 180944 显示外壳 Display Housing
47 72189327 滤光片 Display lens,CHN
183449 滤光片 Display lens,English
72193760 滤光片 Display lens,Euro,bc
48 156439 立杆线束 Harness,Customer display,
49 173248 线束，打印－主板 Harness,Main pcb to printer board
50 72187458 线束，接口－主板 Harness,Main pcb to interface
51 182252 键盘线束 Harness,Main PCB to keyboard
52 171790 显示转接线束 Harness,Segment Disp. convert
173345 显示转接线束 Harness,240x240 Disp. convert
53 72209419 导滑垫板 Slide base
54 72209420 小滑块 Slide space
55 72224370 塑料线卡 Clip
B1 72204992 螺钉 M4X12，GB818-85 SCREW M4X12
B2 119054 铅封头 SEALING HEAD
B3 118549 铅封螺钉 SEALING SCREW
B4 72189609 螺钉 M4X8，GB818-85 SCREW M4X8
B5 72201470 螺钉 M4X6 SCREW M4X6
B6 102504 螺钉，M6X20,GB70-85 SCREW M6X20
B7 72204993 紧定螺钉，M5X16,GB79-85 SLOT SCREW
B8 72194324 方螺母，M4 NUT M4
B9 72201474 自攻螺钉，M2.9X10,GB845 SCREW
B10 72201466 螺钉，M3X6,GB818 SCREW
B11 102661 弹簧垫圈 SPRING WASHERS
105
2
2
2
2
1
1
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
4
4
2
6
1
2
14
24
14
4
1
1
1
1
1
1
1
1
9
B12 72201469 螺钉，M4X14,GB819 SCREW
B13 142884 紧定螺钉，M3X8,GB79-85 SLOT SCREW
B14 72201468 螺钉，M3X6,GB819 SCREW
B15 133022 齿垫 ￠4 WASHERS
6
4
2
2
106
72187321 bPro-U2
72187321 bPro-U2
Item P/N Description
1 180945 压 板 A Sheet Metal,support A,display
107
Qty
1
2 155637 显示屏 Display Assembly,segment,CHN
72189191 显示屏 Display Assembly,segment,EURO
170120 显示屏 Display Assembly,segment,ENG
72202239 显示屏 Display Assembly,240X240
3 180944 显示外壳 Display Housing
4 72189327 滤光片 Display lens,CHN
183449 滤光片 Display lens,English
72193760 滤光片 Display lens,Euro,bc
5 180977 立杆 B Tower B bPro/bC-U2
6 173476 键盘转接板 PCB Assembly,keyboard convert
7 72183679 键盘支架 Sheet Metal,support,keyboard
8 72186085 上键盘盖 Keyboard Housing,Top Cover
9 72186578 银浆电路 Keyboard,Membrane layer
10 72186679 键盘挂钉 Keyboard, Pin
11 72186581 键盘，白色橡胶触点层,bPro-U2 Keyboard, Rubber button padding,bPro U2 1
12 72193809 键盘，操作面板 bPro-U2 英文 Keyboard, Operation layer,bPro U2 ENG 1
13 72186580 键盘，透明硅胶按压层 Keyboard,Touch pad,Silicon,bPro U2
14 102326 水泡 Leveling Bubble
1
1
1
1
1
2
15 124041 中心橡胶垫 Cap,Spider,Center
16 180974 托 架 Spider
17 122206 纸铅封 Sealing Sticker,EU
1
1
1
2
2
2
2
2
2
2
2
1
1
18 72192054 铅封盖板 Sealing Cover
19 154555 角垫 Cap,Spider,,Corner
20 180943 上盖 Main Housing Cover
21 72185423 钣金托架 Spider support
22 174032 A/D 板 PCB Assembly,AD board
23 180951 开关固定板 Sheet Metal,support ,Power Switch
24 72187456 线束，电源开关 Harness,AC power Switch
25 72187455 电源线束 Harness,AC Power Socket
26 72186386 开关电源 24v Switch Power Supply,24v,2.7A
72186387 开关电源 24v Switch Power Supply,24v,4.2A
27 72186444 接口固定板 Sheet Metal,Support,interface
28 173307 接口板 PCB Assembly ,interface
29 183358 基座盖板 Sheet Metal,base cover
30 169795 主板 PCB Assembly ,Main board,standard
72186557 主板 PCB Assembly ,Main board,Premium
31 72188140 秤 脚 Foot,short,right
32 72184997 AMI-22 传感器 Loadcell Assembly,AMI-22
72184996 AMI-40 传感器 Loadcell Assembly,AMI-40
72186985 AMI-11 传感器 Loadcell Assembly,AMI-11
72186878 AMI-40 传感器 Loadcell Assembly,AMI-40 30kg 6000e
1
2
1
1
1
1
1
1
1
1
1
1
1
1
4
1
1
1
1
108
72186875 AMI-40 传感器 Loadcell Assembly,AMI-22 12kg 6000e
33 180973 基座 Aluminum Base Casting
34 72191369 基座小盖板 A COVER A,Base
35 72191370 基座小盖板 B COVER B,Base
36 180975 导轨 Printer Rail Slider
37 72186193 打印机组件 Printer Assembly,2" Label
38 72185419 垫 块 Loadcell spacer
39 173251 立杆线束，点阵 Harness,240x240 Display
72191008 线束，IIC(欧元段码） Harness,segment Display
40 182872 立杆固定座 Sheet Metal,support,Towertobase
41 72186088 立杆盖板 D Plastic Cover,Front,UpperKB
42 72186087 立杆盖板 C Plastic Cover,Rear,UpperKB
43 72183678 显示支架 Sheet Metal,support,display
44 72186402 导轨座 Printer Rail
45 72186086 上键盘座 Keyboard Housing,Base
46 72187458 线束，接口－主板 Harness,Main pcb to interface
47 180947 打印机侧门 Door
48 173248 线束，打印－主板 Harness,Main pcb to printer
49 173596 直流线束 Harness,DC Power
50 167391 秤脚 FOOT,Long,left
51 183021 秤盘组件 Platter
52 182252 键盘线束 Harness,Main PCB to keyboard
53 171790 显示转接线束 Harness,Segment Disp. convert
173345 显示转接线束 Harness,240x240 Disp. convert
54 180952 上盖活动盖板 Label Roll Housing
55 72224370
56 72187457 线束, 键盘转接 Keyboard convert
57 72209419 导滑垫板 Slide base
58 72209420 小滑块 Slide space
59 72224168 显示连接支架，bPro display support metal 1
B1 72201466 螺钉，M3X6,GB818 SCREW 18
1
1
1
1
1
1
1
1
B2 72201474 自攻螺钉，M2.9X6.5,GB845 SCREW
B3 72204992 螺钉 M4X12，GB818-85 SCREW M4X12
6
9
B4 72204993 紧定螺钉，M5X16,GB79-85 SLOT SCREW 4
B5 72201468 螺钉，M3X10,GB819 SCREW 2
B6 72189609 螺钉 M4X8，GB818-85 SCREW M4X8
B7 72201473 螺钉，M6X20,GB70-85 SCREW M6X20
B8 72194324 螺母，M4 NUT M4
B9 72201464 螺钉 M2X6，GB67 SCREW M2X6
B10 72201470 带齿垫螺钉 M4X5 SCREW M4X5
B11 150684 开口挡圈 3.2 CIRCLIPS 3.2
21
2
9
4
2
2
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
109
B12 102661 弹簧垫圈 SPRING WASHERS
B13 72201469 螺钉，M4X14, GB819 SCREW
4
3
110
METTLER TOLEDO
Scales & Systems
1900 Polaris Parkway
Columbus, Ohio 43240
P/N: 72186164
(3/09).02
METTLER TOLEDO
® is a registered trademark of Mettler-Toledo, Inc.
©
2000 Mettler-Toledo, Inc.
Printed in China
72186164
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project