Ex i- user interfaces

Ex i- user interfaces
User’s manual to
Ex i- user interfaces
TB153
0044
KB153
1 safe use
page 2
Contents
1
1
Operation instruction for Explosion protected device..................... Fehler! Textmarke nicht definiert.
Ex i- user interface devices .................................................................................................................. 5
1.1
Tracker ball TB153.1.0 / TB153.1.1 - properties............................................................................ 5
1.2
Tracker ball TB153.x.2 - properties................................................................................................ 5
1.3
Tracker ball TB153.x.3 - properties................................................................................................ 5
1.4
Joystick TB153.x.4-7 - properties .................................................................................................. 5
2 Mounting and connection ...................................................................................................................... 5
2.1
Mounting ........................................................................................................................................ 5
2.1.1
General instructions................................................................................................................ 5
2.1.2
Instructions to ambient housing of TB153.0.x ........................................................................ 6
2.1.3
Instructions to Joystick TB153.0.4-7....................................................................................... 6
2.1.4
Instructions to Ex i- circuits ..................................................................................................... 6
2.2
Isolation proof................................................................................................................................. 6
3 Technical Details ................................................................................................................................... 7
3.1
Technical Details and limits ........................................................................................................... 7
3.1.1
Limits TB153.x.1, TB153.x.2 and TB153.x.3 .......................................................................... 7
3.1.2
Limits TB153.x.4-7 .................................................................................................................. 7
Gönnheimer Elektronic GmbH
Tel.: +49 (6321) 49919-0
Fax: +49 (6321) 49919-41
KB153
5 Annex
page 3
The symbols WARNING, CAUTION, NOTE
This symbol warns of a serious hazard. Failure to observe
this warning may result in death or the destruction of property.
This symbol warns of a possible failure. Failure to observe
this caution may result in the total failure of the device or the
system or plant to which it is connected.
This symbol highlights important information.
Gönnheimer Elektronic GmbH
Tel.: +49 (6321) 49919-0
Fax: +49 (6321) 49919-41
KB153
1
5 Annex
page 4
Operation instruction for Explosion protected device
Application and Standards
This instruction manual applies to explosion-protected control panels of type of protection types
below. This apparatus is only to be used as defined and meets requirements of EN 60 079 particularly EN60 079-14 "electrical apparatus for potentiality explosive atmospheres".
Use this manual in hazardous locations, which are hazardous due to gases and vapors according
to the explosion group and temperature class as stipulated on the type label. When installing and
operating the explosion protected distribution and control panels you should observe the respective nationally valid regulations and requirements.
General Instructions
The device has to have a back-up fuse as stipulated. The mains connection must have a sufficient short circuit current to ensure safe breaking of the fuse. To achieve an impeccable and
safety device operation, please take care for adept transportation, storage and mounting, as well
as accurate service and maintenance. Operation of this device should only be implemented by
authorized persons and in strict accordance with local safety standards.
The electrical data on the type label and if applicable, the "special conditions" of the test certificate TÜV 99 ATEX 1442 are to be observed.
For outdoor installation it is recommended to protect the explosion protected distribution and control panel against direct climatic influence, e.g. with a protective roof. The maximum ambient temperature is 40°C, if not stipulated otherwise.
Intrinsically Safe Circuits
Erection instructions in the testing certificates of intrinsically safe apparatus are to be observed.
The electrical safety values stipulated on the type label must not be exceeded in the intrinsically
safe circuit. When interconnecting intrinsically safe circuits it is to be tested, whether a voltage
and/or current addition occurs. The intrinsic safety of interconnected circuits is to be ensured. (EN
60079-14, section 12)
Safety Measures: to read and to comply
Work on electrical installations and apparatus in operation is generally forbidden in
hazardous locations, with the exception of intrinsically safe circuits. In special cases
work can be done on non-intrinsically safe circuits, on the condition that during the
duration of such work no explosive atmosphere exists. Only explosion protected
certified measuring instruments may be used to ensure that the apparatus is voltage-free. Grounding and short-circuiting may only be carried out, if there is no explosion hazard at the grounding or short circuit connection.
Danger of static charge!
Clean only with humid cloth!
Do not open when an explosive dust atmosphere is
present!
Gönnheimer Elektronic GmbH
Tel.: +49 (6321) 49919-0
Fax: +49 (6321) 49919-41
KB153
5 Annex
page 5
1 Ex i- user interface devices
1.1 Tracker ball TB153.1.0 / TB153.1.1 - properties
9 2 keys and stainless steel ball 38 / 50 mm
9 Water and dust proof acc. to IP65
1.2 Tracker ball TB153.x.2 - properties
9 Alternative industrial device
9 Alternative pointing device without moving parts
9 Water and dust proof acc. to IP65
1.3 Tracker ball TB153.x.3 - properties
9
9
9
9
Alternative industrial device
Very compact pointing device
Alternative pointing device without moving parts
Water and dust proof acc. to IP65
1.4 Joystick TB153.x.4-7 - properties
9 Precise and comfortable navigation
9 Alternative pointing device
9 Water and dust proof acc. to IP65
2 Mounting and connection
2.1 Mounting
The TB153 could be mounted in Ex area Zone 1.
2.1.1
General instructions
With the assembly the local installation regulations,
in particular the regulations are to be followed in EN
60079, in particular EN 60079-14.
TB153.x.x
The mounting plate of the device TB153.0.2 should
be connected to the potential earth (PE). If an ambient housing is used ( e.g.TB153.0.4-7) this housing
should also be connected to PE.
The devices without housing (TB153.0.x) should be
mounted into a housing with min. protection class of
IP 20 at clean and dry ambient conditions.
At other ambient conditions the housing with have
min. protection class of IP65
The IP protection should not be corrupted by improper build in of the Ex i- interface device.
Gönnheimer Elektronic GmbH
Tel.: +49 (6321) 49919-0
Fax: +49 (6321) 49919-41
KB153
2.1.2
5 Annex
page 6
Instructions to ambient housing of TB153.0.x
See housing instructions according to EN 60079-0;
chapter 7.3.2 (prevention of electro static discharge)
and 8.1.2 (light metal - combination), as well as EN
60079-14; chapter 5.6 und 6.4 and the EC – type certificate TÜV 99 ATEX 1442
TB153.0.x
2.1.3
Instructions to Joystick TB153.0.4-7
The rubber collar on the joystick is part of the IP protection.
Harmed joysticks must be replaced immediately
TB153.0.4-7
2.1.4
Instructions to Ex i- circuits
TB153.x.x
Using the types TB153.0.x the Ex i- connections
should be mounted “floating” (Free of ground)
(see EN60079-14, chap. 12.2.4)
This is valid up to the barrier as well to all other connections (i.e. keys to the tracker ball and controller
PCBs)
Use synthetic screws to mount the PCB to achieve
the “free of ground” mounting.
The floating of the Ex i- connection must be tested
(chap. 3.2: isolation proof )
2.2 Isolation test
Floating test acc. to EN60079-11; chap. 6.3.12
Disconnect the KI153 before testing !!
Gönnheimer Elektronic GmbH
Tel.: +49 (6321) 49919-0
Fax: +49 (6321) 49919-41
KB153
5 Annex
page 7
3 Technical Details
3.1 Technical Details and limits
3.1.1 Limits TB153.x.1, TB153.x.2 and TB153.x.3
TB153 as tracker ball, industrial mouse or miniature- mouse
Terminal
1 Pin 1, 2, 3
1 Pin 4
voltage Ui
Current Ii Power Pi Ci, Li
Comment
5,8V
204mA
392mW
5µF, 0mH Power supply and data
PE
3.1.2 Limits TB153.x.4-7
TB153 as joystick
Terminal
1 Pin 1, 2, 3
1 Pin 4
voltage Ui
Current Ii Power Pi Ci, Li
Comment
5,8V
204mA
392mW 25µF, 0mH Power supply and data
PE
Gönnheimer Elektronic GmbH
Tel.: +49 (6321) 49919-0
Fax: +49 (6321) 49919-41
Non authorized translation
(1)
EC- TYPE- EXAMINATION CERTIFICATE
(Translation)
(2)
Equipment and protective systems intended for use in
potential explosive Atmospheres – Directive 94/9/EC
(3)
EC- type- examination Certificate number
TÜV 99 ATEX 1442
(4)
Equipment:
trackball type TB 153
(5)
Manufacturer:
Gönnheimer Elektronic GmbH
(6)
Address:
67433 Neustadt an der Weinstraße, Dr.-Julius-Leber-Straße 2
(7)
This equipment and any acceptable variation thereto are specified in the schedule to
this certificate and the documents therein referred to.
(8)
The TÜV Hannover/Sachen-Anhalt e.V., TÜV CERT-Zertifizierungsstelle, notified body
No. 0032 in accordance with Article 9 of the Council Directive 94/9/EC of March 1994,
certifies that equipment has been found to comply with the Essential Health and
Safety Requirements relating to the design and construction of equipment and
protective systems intended for use potentially explosive atmospheres, given in Annex
II to the Directive.
The test results are recorded in the confidential report No. 99/PX12592.
(9)
Compliance with to essential Health and Safety Requirements has been assured by
compliance with:
EN 50 014:1997
EN 50 020:1994
(10)
If the sign “X” is places after the certificate number, it indicates that the equipment is
subject to special conditions for safe use specified in the schedule to this certificate.
(11)
This EC- type- examination Certificate relates only to the design and construction of
the specified equipment in accordance with Directive 94/9/EC. Further requirements of
this Directive apply to the manufacture and supply of this equipment.
(12)
The marking of the equipment shall include the following:
II 2 G EEx ib IIC T4
TÜV Hannover/Sachen-Anhalt e.V.
TÜV CERT-Zertifizierungstelle
Am TÜV 1
D-30519 Hannover
Hannover, 17.06.1999
Der Leiter
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 1 of 5
Non authorized translation
(13)
SCHEDULE
(14)
(15)
EC- TYPE-Examination CERTIFICATE No. TÜV 99 ATEX 1442
Description of equipment
The trackball TB153 could be used in Ex- hazardous areas. The build-in trackball
types must be placed in housing with at IP20 housing protection according to EN
60529 at least.
The maximum ambient temperature is 50°C.
Electrical details
Power supply and signal
circuits
(clamp 1, Pin 1 ..4)
In protection type intrinsic Safety EEx ib IIC
Exclusive connection to a certificated intrinsically
safe current circuit; Highest values each channel:
U0 = 5,8 V
I0 = 204 mA
P0 = 392 mW
effective internal capacity
5 µF
effective internal inductivity is negligible
(16)
The test documents are listed in report No. 99/PX12592
(17)
Special conditions for safe area
none
(18)
Essential health and safety requirements
No additional
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 2 of 5
Non authorized translation
1. Amendment
to
the Conformity Certificate Nr. TÜV 99 ATEX 1442
Manufacturer:
Gönnheimer Elektronic GmbH
Dr.-Julius Leber-Str.2
D-67433 Neuststadt/Weinstraße
The trackball type TB 153 can also be manufactured according to the examination protocol,
listed in the associated examination certificate. The changes are related to the external build
up. In future there is also a type with a flexible rubber plate as input device.
The extended type code is TB153.x.x
The electrical data and all further specification remain unchanged.
(16)
The test documents are listed in report No. 01 YEX 137375
(17)
Special conditions for safe area
none
(18)
Essential health and safety requirements
No additional
TÜV NORD CERT GmbH & Co. KG
Hannover, 16.10.2001
TÜV CERT-Zertifizierungsstelle
Am TÜV 1
0-30519 Hannover
Der Leiter
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 3 of 5
Non authorized translation
2. Amendment
to Conformity Certificate Nr. TÜV 99 ATEX 1442
Device:
trackball type TB153
Manufacturer:
Gönnheimer Elektronic GmbH
Address:
Dr.-Julius Leber-Str.2
D-67433 Neuststadt/Weinstraße Germany
Order number:
8000553911
Date:
25.02.2008
Changes:
The trackball type KB 153 can also be manufactured according to the examination protocol,
listed in the associated examination certificate. The changes are related to additionally input
devices.
The additional type TB153.0.4 and TB153.0.7 serves as joysticks and if necessary 2 further
buttons as input media.
The entry to the allowed environment temperature is valid consistently also for the
supplemental types.
The additional types own a fixed connected access line and are usable to build in housing
with mind. IP 20 according to EN 60529 intended.
The electric data of the base certificate as well the 1st supplement becomes supplemented
as follows:
Trackball type TB153.0.4 up to TB153.0.7
In protection type intrinsic Safety EEx ib IIC
Power supply and signal circuits
Exclusive connection to an USB 1.x Hub the certified
(supply cable with USB plug)
keyboard interface KI153 according to TÜV 99 ATEX
1440 X, 1. amendment inclusive
Highest values:
UI = 5,8 V
II = 204 mA
P0 = 392 mW
effective internal capacity 25 µF
effective internal inductivity 3 µH.
All further specifications remain unchanged.
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 4 of 5
Non authorized translation
3. Amendment to certification number: TÜV 99 ATEX 1442
The device according to this 2. amendment fulfils requests to the following standards:
EN 60079-0: 2004
EN 60079-11:2007
(16)
The test documents are listed in report No. 07203553911
(17)
Special conditions for safe area
none
(18)
Essential health and safety requirements
No additional
TÜV NORD CERT GmbH, Langemarckstraße 20, 45141 Essen, akkreditiert durch die Zentralstelle der Länder für
Sicherheitstechnik (ZLS), Ident. Nr. 0044, Rechtsnachfolger der TÜV NORD CERT GmbH & Co. KG Ident. Nr.
0032
Der Leiter der Zulassungstelle
Schwed
EC-type-examination Certificates without signature and official stamp shall not be valid. The certificates may be circulated only
without alteration. Extracts or alterations are subject to approval by the TÜV Hannover/Sachsen-Anhalt e.V.
Page 5 of 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising