Aposen ST600 Instruction Manual

ST600 Vacuum Cleaner
Instruction Manual
MODEL NO.: ST600
CONTENT
IMPORTANT SAFEGUARDS
01
GETTING TO KNOW YOUR VACUUM CLEANER
02
TECHNICAL SPECIFICATIONS
03
OPERATING INSTRUCTIONS
03
RECOMMENDATIONS FOR ACCESSORY USAGE
05
WINDING & UNWINDING THE POWER CORD
05
POWER SWITCH
06
USING THE APPLIANCE AS AN UPRIGHT VACUUM
06
USING THE APPLIANCE AS A HANDHELD VACUUM
06
CLEANING & CHANGING THE DUST CUP FILTER
07
TROUBLESHOOTING
08
IMPORTANT SAFEGUARDS
When using your vacuum cleaner, basic safety precautions should always be followed. Read all below
instructions before using.
WARNING: to avoid the risk of fire, electric shock or injury:
1. Use the system only for its intended use.
2. To avoid a risk of electric shock, do not immerse any part of the appliance in water or other liquids.
3. Never yank the cord to unplug it from the socket, instead please grasp plug to unplug it from the
socket.
4. Do not allow cord to touch hot surfaces.
5. Do not operate the system with a damaged cord or plug, or if the appliance or any other part of the
system has been dropped or damaged. To avoid the risk of electric shock, do not disassemble or
attempt to repair the vacuum cleaner. Return the unit for examination and repair. Incorrect
re-assembly or repair can cause a risk of electrical shock or injury to persons when the vacuum
cleaner is used.
6. Close supervision is necessary for any appliance being used by or near children. Do not leave the
appliance unattended while it's plugged.
7. Keep hair, loose clothing, fingers and all parts of body away from opening and moving parts.
8. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where
they may be present.
9. Do not pick up anything that is burning or smoking such as cigarettes, matches or hot ashes.
10. Pay extra attentions when cleaning on stairs in case of falling or tripping.
11. Do not use the vacuum without the dust cup filter installed in place.
12. This appliance is intended for household use only. Follow all user instructions in this manual.
13. Unplug the power cord when not in use and before servicing.
14. Use only as described in this manual. Use only manufacturer’s recommended accessories.
15. Do not pull cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or
corners.
16. Turn off the power switch before unplugging it from the socket.
17. Do not handle plug or vacuum with wet hands or operate without shoes.
18. Do not put any objects into openings. Do not use with any opening blocked. Keep free of dust, lint,
hair and anything else that may reduce air flow.
19. Store your appliance indoors in a cool, dry area.
01
20. Do not immerse the vacuum in water or other liquids.
21. Keep end of hose, wands and openings away from your face & body.
22. Use the appliance on dry surfaces only.
23. Using improper voltage may result in damage to the motor and possible injury to the user. Correct
voltage is listed on rating label.
For Household Use Only.
SAVE THESE INSTRUCTIONS FOR FURTHER REFERENCE
WARNING:
To reduce the risk of injury from moving parts-Unplug before maintenance.
To reduce the risk of injury of electric shock-Unplug before cleaning or maintenance.
To reduce the risk of electric shock-Do not use outdoors or on wet surfaces.
GETTING TO KNOW YOUR VACUUM CLEANER
1. Extension tube handle
2. Release cord hook
3. Handle assembly
4. Extension tube
5. The main body
6. On/Off power switch
7. Dust cup lock
8. Dust cup
9. Floor brush assembly
10. Crevice tool
11. Air exhaust
12. On/Off power switch
13. Power cord
02
TECHNICAL SPECIFICATIONS
Model Number
ST600
Voltage
120V
Power
600W
Dust cup capability
0.5L
Suction Power
15Kpa
OPERATING INSTRUCTIONS
Note:
Always remove the power plug from the wall outlet before assembling or removing accessories
Inserting the metal extension tube into the main body
Hold the hand vacuum and the extension tube, make the node (Fig.1) on the extension tube to be in
line with the hole(Fig.2) on the vacuum cleaner then insert the tube into the hand vacuum hole.
2
1
03
Push the tube into the vacuum cleaner until you heard a "click" sound as the tube will be locked into
place.(Fig. 3)
Pull the handle upwards to make sure the tube is locked into the hole(Fig.4)
4
3
To detach the extension tube, press the release button on the side of vacuum cleaner and pull out(Fig. 5)
5
Attaching the floor brush to the main body
Push the floor brush into the suction hole opening.
04
Using the crevice tool
Push the end of crevice tool back(Fig.6) and turn it 180 degree(Fig.7), then push the other end of
crevice tool into the suction hole(Fig.8).
6
7
8
RECOMMENDATIONS FOR ACCESSORY USAGE
Crevice tool: for radiators, crevices, corners, base-boards and between cushions.
Floor brush: for all kinds of flooring, including carpeted and tiled floors.
WINDING & UNWINDING THE POWER CORD
This vacuum cleaner is equipped with a convenient cord storage feature.
• This unit also has a quick release cord hook.
• Wind power cord around the quick release cord hook and the cord winding hook.(Fig.9 & Fig.10).
• To unwind the power cord, simply twist the quick release cord hook to the left or right.
10
9
Caution:
The suction opening must be o pen and free of any obstructions at all times. Otherwise, the
motor will overheat and could get damaged.
05
POWER SWITCH
• There are two On/Off power switch on the appliance. (Fig.11 & Fig.12)
• Push on the “I” side to turn the vacuum ON.
• Push on the “O” side to turn the vacuum OFF.
11
12
USING THE APPLIANCE AS AN UPRIGHT VACUUM
• Insert the extension tube into the hand vac.
• Choose the appropriate accessory (crevice tool or floor brush) and use it as suction opening on the
hand vac.
• Press the “I” position on the On/Off power switch turn the unit on.
When finished using the unit, press the “O” position on the On/Off power switch to turn the unit off.
• When finished using the unit, wind the power cord around the cord winding hooks for easy storage.
USING THE APPLIANCE AS A HANDHELD VACUUM
• Disassemble the extension tube from the hand vac by releasing the handle port from the locking clip
and removing the extension tube from the hand vac handle.
• Note: You may choose to leave the crevice tool or floor brush attached to the hand vacuum when
operating as such.
Press the “I” position on the On/Off power switch to turn the unit on. When finished using the unit,
press the “O” position on the On/Off power switch to turn the unit off.
06
CLEANING & CHANGING THE DUST CUP FILTER
Changing and cleaning the dust cup filter
In order to achieve the best performance, empty the dust cup and clean the dust cup filter after each
use.
1. To remove the dust cup, press down on the dust cup release button (Fig. 13) and separate the dust
cup from the main body. (Fig. 14)
13
14
2. Pull out the dust cup filter assembly(Fig. 15), then twist the HEPA filter frame to take out HEPA
filter(Fig.16).
15
16
3. Dump the dust from the dust cup.
4. Rinse the dust cup filter in cold water, and then let it air-dry for 24 hours before placing it back in the
dust cup.
07
Important Note:
DO NOT use a washing machine to clean the dust cup filter.
Do NOT use a hair dryer to dry it.
AIR-DRY ONLY.
5. Install the dust cup filter carefully into the dust cup compartment.
NEVER operate the vacuum cleaner without the dust cup filter installed in place.
6. Attach the dust cup to the main body of the unit.
Note:
It is recommended that the dust cup filter be cleaned every week(depending on usage) to ensure
peak performance of the unit.
TROUBLESHOOTING
Problem
Vacuum does not
operate
Vacuum cleaner does
not pick up dust or
the suction power is
weak
POSSIBLE REASONS
No electricity comes from the
socket. The fuse and breaker
malfunctions.
1. Check and replace the fuse or
breaker.
2. Change the socket for plugging in
the appliance to try again.
1. Empty dust cup.
1. Dust cup is full.
2. Dust cup filter requires
cleaning or replacement.
3. The appliance needs to be
charged.
1. Dust cup is full.
Dust escaping from
the suction hole of
the vacuum cleaner
POSSIBLE SOLUTION
2. Dust cup filter is not
installed correctly.
3. There are puncture/hole in
the dust cup filter.
2. Remove dust filter and check for
object(s) in air duct and remove.
Clean or replace the HEPA filter.
3. Charge the appliance.
1. Empty dust cup.
2. Review the dust cup filter
installation instructions.
3. Replace dust cup filter.
If you have a query about your APOSEN appliance, please contact the APOSEN customer service
email: [email protected]
08