Linak Deskline DL20 IC User Manual

DL20 IC/DL21 IC system
User manual
LINAK.COM/DESKLINE
Page 1 of 32
Contents
Preface........................................................................................................................................... 3
Valid for ......................................................................................................................................... 4
Important information ................................................................................................................ 5
Safety instructions........................................................................................................................
Safety issues..............................................................................................................................
Before installation, reinstallation or troubleshooting...................................................................
Before start-up..........................................................................................................................
During operation........................................................................................................................
Misc .........................................................................................................................................
5
6
7
7
7
7
Only for EU markets...................................................................................................................... 8
Only for Non-EU markets............................................................................................................. 8
Misuse............................................................................................................................................ 8
Repairs............................................................................................................................................ 9
Declaration of incorporation of partly completed machinery ............................................... 9
Declaration of Conformity ......................................................................................................... 10
Misc. on the DESKLINE® DL20 IC/DL21 IC system ..................................................................
Warranty ................................................................................................................................
Maintenance ..........................................................................................................................
Cleaning the desk panel ..........................................................................................................
Service of double-insulated products .......................................................................................
12
12
12
12
13
ETL-marking ..................................................................................................................................14
Description of the DESKLINE® DL20 IC/DL21 IC system ......................................................... 15
Installation
Mounting the DL20 IC/DL21 IC system ......................................................................................16
Mount the motor housing ........................................................................................................ 16
Mounting the feet .................................................................................................................... 17
Mounting the tabletop.............................................................................................................. 18
Placing the monitor................................................................................................................... 18
Connection............................................................................................................................... 19
Accessories .................................................................................................................................. 20
Disposal of LINAK products ....................................................................................................... 21
Labels............................................................................................................................................ 22
Drawing appendix ........................................................................................................................23
Addresses ..................................................................................................................................... 32
Page 2 of 32
Preface
Dear User,
We are delighted that you have chosen a product from LINAK®.
LINAK systems are high-tech products based on many years of experience in the manufacture and development
of actuators, electric control boxes, controls and chargers.
This User Manual does not address the end-user. It is intended as a source of information for the manufacturer
of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics.
It is the responsibility of the manufacturer of the end-user product to provide a User Manual where relevant
safety information from this manual is passed on to the end-user.
We are sure that your LINAK product/system will give you many years of problem-free operation.
Before our products leave the factory, they undergo full function and quality testing. Should you nevertheless
experience problems with your LINAK product/system, you are always welcome to contact your local contact.
LINAK subsidiaries and some distributors situated all over the world have authorised service centres, which are
always ready to help you.
LINAK provides a limited warranty on its products. This warranty is, however, subject to correct use in
accordance with the specifications, maintenance being done correctly, and any repairs being carried out at a
service centre, which is authorised to repair LINAK products. Changes in installation and use of LINAK products/
systems can affect their operation and durability. The products are not to be opened by unauthorised personnel.
You can review the full terms of the LINAK warranty on the LINAK website www.linak.com/warranty.
The User Manual has been written based on our present technical knowledge. We are constantly working on
updating the information and we therefore reserve the right to carry out technical modifications.
LINAK A/S
Page 3 of 32
Valid for:
This User Manual is valid for the following products:
(See the first 3 - 5 characters on the label)
Columns:
2 lifting columns DL20 IC / DL21 IC
Power supply:
SMPS001, SMPS002 or SMPS006
Controls:
DPA / DPB / DPH / DP1K / DPF1K / DPG1K
Page 4 of 32
Important information
Important information on LINAK® products can be found under the following
headings:
Warning!
Failure to comply with these instructions may result in accidents involving
serious personal injury.
Failing to follow these instructions can result in the product being damaged
or being destroyed.
Safety instruction
General
Safe use of the system is possible only when the operating instructions are read
completely and the instructions contained are strictly observed.
Failure to comply with instructions marked with the ”NOTE” symbol may result in
serious damage to the system or one of its components.
It is important for everyone who is to connect, install, or use the systems to
have the necessary information and access to this User Manual. Follow the
instructions for mounting – there is a risk of injury if these instructions are not
followed.
The appliance is not intended for use by young children or infirm persons
without supervision.
If there is visible damage to the product, do not install it.
Please note that during construction of applications in which the actuator
is to be fitted, there must be no possibility of personal injury, for example
squeezing of fingers or arms.
Only the power supply type SMPS001, SMPS002 or SMPS006, shall be used
with the system.
The power supply shall not be covered while operating to allow sufficient
cooling of this appliance.
Page 5 of 32
Furthermore take care about the connecting wires from the power supply to the
DL20 IC / DL21 IC system, don’t damage this by overrun.
Assure free space for movement of the application in both directions to avoid
blockades.
The appliance is only to be used with the power supply unit provided with
the appliance.
Safety issues
The builder of the equipment shall ensure that the use of the component
complies with relevant standards – like the Machine Directive. Care must be
taken to avoid squeezing of cables as it can cause movement of the system!
The SMPS001 / SMPS002 / SMPS006 must not be packed in heat insulating
material, but must be placed so that it can emit waste heat to the surroundings.
There are no ventilation holes to consider, the SMPS emits heat through its
surface.
Only the power supply type SMPS001, SMPS002 or SMPS006, shall be used
with the system.
Page 6 of 32
Before installation, re-installation, or troubleshooting
• Stop the DL
• Pull out the mains plug.
• Relieve the DL of any loads, which may be released during the work.
Before start-up
• Make sure that the system has been installed as instructed in this User Manual.
• Make sure that the voltage of the control box is correct before connecting the
system to the mains.
• System connection. The individual parts must be connected before connecting the
control box to the mains. See the User Manual for LINAK actuators, if necessary.
During operation
• If the control box makes unusual noise or smells, switch off the mains voltage
immediately.
• Take care that the cables are not damaged.
• Unplug the mains cable on mobile equipment before moving it.
• The products must only be used in an environment, that corresponds to their IP
protection.
Misc.
The actuator system has a sound level below 55 dB (A) in typical applications.
Updated manuals and declarations can always be found here:
www.linak.com/deskline
Page 7 of 32
Only for EU markets
This appliance can be used by children aged from aged 8 years and above
and persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
Only for Non EU markets
Persons who do not have the necessary experience or knowledge of the
product/products must not use the product/products. Besides, persons with
reduced physical, sensory or mental abilities must not use the product/
products, unless they are under surveillance or they have been thoroughly
instructed in the use of the apparatus by a person who is responsible for the
safety of these persons.
Moreover, children must be under surveillance to ensure that they do not play
with the product.
Misuse
Do not overload the actuators – this can cause danger of personal injury and
damage to the system.
Do not use the actuator system for lifting persons. Do not sit or stand on a
table while operating – risk of personal injury.
Do not use the system in environments other than the intended indoor use
Page 8 of 32
Repairs
In order to avoid the risk of malfunction, all DESKLINE® repairs must only be carried out by authorised LINAK service centres or
repairers, as special tools must be used and special gaskets must be fitted. Products under warranty must also be returned to
authorised LINAK service centres.
Further information on DESKLINE warranty can be found on the LINAK website www.linak.com/warranty.
Warning!
If any of the DESKLINE ® products are opened, there will be a risk of subsequent malfunction.
Warning!
The DESKLINE ® systems do not withstand cutting oil.
Page 9 of 32
DECLARATION OF CONFORMITY
LINAK A/S
Smedevænget 8
DK - 6430 Nordborg
hereby declares that LINAK Actuator System composed of:
Lifting Column with integrated control, DLIC Master:
DLXXXXXXMXXXXXX or
DLXXXXXXMXXXXXX
And
Passive Actuators, DLIC Slave
DLXXXXXXSXXXXXX or
DLXXXXXXSXXXXXX
And
Control panel
DP1C, DP1K, DPT, DPB, DPF, DP1L, DP1V, DPA, DPH, DP1U,
WDPL1
complies with EMC Directive: 2014/30/EU according to following standards:
EN 61000-6-1:2007, EN 61000-6-3:2007, EN 55022:2010 Class B
complies with Low Voltage Directive 2006/95/EC according to the standards:
EN 60335-1:2012
complies with RoHS2 Directive 2011/65/EU according to the standard:
EN 50581:2012
And
RF Control:
RFRL00x, HB1xRF3000, HB2xRFx000; RFT000
complies with the Radio Equipment Directive 2014/53/EU:
EN 300220-2:2006, EN 61000-6-1:2007, EN 61000-6-3:2007,
EN 60335-1:2012, EN 62311:2008
complies with RoHS2 Directive 2011/65/EU according to the standard:
EN 50581:2012
Nordborg, 2017-08-25
LINAK A/S
John Kling, B.Sc.E.E.
Certification and Regulatory Affairs
Authorized to compile the relevant technical documentation
Original Declaration
Page 10 of 32
Declaration of conformity
DECLARATION OF CONFORMITY
LINAK A/S
Smedevænget 8
DK - 6430 Nordborg
hereby declares that LINAK Switch Mode Power Supply, type SMPS006
complies with the EMC Directive: 2014/30/EU according to following standards:
EN 61000-6-1:2007, EN 61000-6-3:2007
complies with Low Voltage Directive 2014/35/EU according to the standard:
EN 61558-2-16:2009
complies with RoHS2 Directive 2011/65/EU according to the standard:
EN 50581:2012
This declaration of conformity is issued under the sole responsibility of the manufacturer
The RoHS mark is only applicable for the end product. Therefore, it must be obtained by the manufacturer of the
end products. LINAK® can, however, supply the required material information on our products.
For more information, visit: https://www.linak.com/about-linak/csr/declarations/
or contact: [email protected]
Page 11 of 32
Misc. on the DESKLINE® DL20 IC / DL21 IC system
This system is a DESKLINE system developed for desks applications ranging from industry to office desks and for indoor use. Do
not use it in industrial kitchens or in other enviroments that have to be cleaned with aggressive detergents.
Do not bolt the legs to the floor so that free movement is prevented. This could cause serious damage to the legs in fault
situations.
Warranty
This DESKLINE product is subject to warranty pursuant to the terms of LINAK DESKLINE Warranty Paper, available on the LINAK
website www.linak.com/warranty.
Maintenance
Clean dust and dirt from the outside of the system at appropriate intervals and inspect for damage and breaks.
Inspect connections, cables, and plugs without disconnecting, and check functioning as well as fixing points.
Cleaning the desk panel
Clean your desk panel with a soft damp cloth. Universal cleaning detergents may be used.
For disinfection of the desk panel, use a 70 percent isopropyl alcohol either as a wipe or add a small amount to a soft cloth.
The desk panel is not a sealed unit and there are electronics inside it.
If liquids or moisture enter an opening, the PCB may be damaged, and the desk panel ruined.
Thus:
• Avoid moisture penetrating any openings as this may damage the PCB inside the desk panel
• Avoid spraying the cleaning agent or disinfectant directly on the desk panel as moisture may
penetrate openings damaging the PCB inside the desk panel
• Cleaning agents and disinfectants must not be highly alkaline or acidic (pH value must be 6 to 8),
and they must not contain bleach or chlorine
• Do not use hand sanitizer gel as a cleaning agent
Page 12 of 32
Service of double-insulated products:
Class II
A Class II or double insulated electrical appliance is one which has been designed in such a way that it does not require a
safety electric earth connection (US: ground).
The basic requirement is that no single failure can result in dangerous voltage becoming exposed so that it might cause an
electric shock and that this is achieved without relying on an earthed metal casing. This is usually achieved at least in part by
having two layers of insulating material surrounding live parts or by using reinforced insulation.
There is no earthing/grounding means provided on the product, and no earthing/grounding means is to be added to the
product.
In Europe, a double insulated appliance must be labelled “Class II”, “double insulated” or bear the double insulation symbol (a
square inside another square).
Servicing a double-insulated product requires extreme care and knowledge of the system, and is to be done only by qualified
service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace.
Cleaners and disinfectants must not be highly alkaline or acidic (pH value 6-8).
Page 13 of 32
ETL-marking
Due to space limitations, the complete ETL-marking demands are not represented on the marking plates.
The full ETL Recognized Component markings are shown here.
C/N 120690
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United
States
C/N 9901916
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United
States
C/N 4008003
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
C/N 4008004
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
C/N 4008005
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
C/N 4008671
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
C/N 4009507
Conforms to UL962
Cert. to CSA Std. C22.2 No. 68-09
ETL Recognized Component mark for Canada and United States
Page 14 of 32
Description of the DESKLINE® DL20 IC / DL21 IC system
Each DESKLINE® DL20 IC/DL21 IC lifting unit is equipped with a motor, and parallel/memory drive is ensured by means of
software in the master column that also takes account of oblique load on the desk.
Application of the DESKLINE® DL20 IC/DL21 IC:
Irrespective of the load, the duty cycle 10 % ≈ 2 minutes continuous use at full load, followed by 18 minutes
pause stated in the data sheets, must NOT be exceeded as this will result in a superheating of the motor, the brake and the
spindle nut. Exceeding the duty cycle will result in a dramatic reduction of the life of the system.
A typical DL IC system consists of:
• 2 lifting columns: DL20 IC/DL21 IC (one Master and one Follower)
• Power supply SMPS001, SMPS002 or SMPS006
• Desk panel DPA, DPB, DPH, DP1K, DPF1K or DPG1K
• Exchangeable cables
Page 15 of 32
Installation
Mounting the DL20 IC / DL21 IC system
Mounting the motor housing
The motor housing is supplied with six M6 threaded holes for mounting on the top frame.
1. Mount motor housing on top frame using six M6 screws with the following specifications:
Quality: Min. grade 8.8
Length: Max. 10 mm (plus top frame thickness). The bolt must not go further than max. 10 mm into the motor housing
2. Fasten screws thoroughly (torque: max. 7.5 Nm).
Always use six M6 bolts for mounting the motor housing on the top frame
Mounting bolts must not go further than max. 10 mm into the motor housing
Sufficient stability of the desk is only obtained if all six M6 screws are used for mounting the motor housing
on the top frame. Tests with fixing the motor housing using only four M6 screws have proved that the torsional
stability of the desk this is insufficient.
LINAK recommends using the DL IC DESKLINE® system in push applications with the motor housing mounted
upwards.
Page 16 of 32
Mounting the feet
The DL20 IC / DL21 IC bottom plate is supplied with four M6 and two M8 threaded holes.
1. Mount column bottom on desk feet using four M6 or two M8 screws with the following specifications:
Quality: Min. grade 8.8
Length: Min. 10 mm (plus foot thickness);
Max. 16 mm (plus foot thickness) for M6
Max. 14 mm (plus foot thickness) for M8
Min. 10 mm
Max. 14 mm
2. Fasten screws thoroughly (torque: max. 10 Nm).
The holes in the foot must be sufficiently larger than ø6/ø8 to ensure space for the screw heads to be
screwed fully into the foot.
M8
Drawing No.: SAMLET_SKRUE_BILLED
Min. 10 mm
Max. 14 mm
Min. 10 mm
Max. 16 mm
Bottom plate
M6
M8
Min. 10 mm
Max. 16 mm
Column bottom mounted on desk foot (left: M6; right: M8)
Page 17 of 32
Mounting of the tabletop
The sound from the lifting column spreads as vibrations to the tabletop which amplifies the sound.
This can, however, be reduced.
1. Place vibration/shock-absorbing material between tabletop and top frame.
Assembled desk
Placing the monitor
Placement of a monitor directly above the motor housing may cause malfunction of the monitor.
Magnets inside the motor may interrupt the picture on the monitor depending on distance and type of monitor. If this is the
case, the problem may be solved by placing an iron plate/tube or another magnetic material, somewhat larger than the motor
housing, between the motor and the tabletop.
Recommended placement of an iron plate/tube or another magnetic material
Page 18 of 32
Connection:
Items required:
Motor cable
Desk panel (example)
1. Connect the master and follower columns using the motor cable.
2. Mount the desk panel onto the desk and connect it to the master column.
3. Connect the SMPS to the master column and to the mains.
Page 19 of 32
SMPS + cable
Accessories
Ordering accessories
Order from your nearest LINAK® contact, distributor or subsidiary.
Accessories
Please contact your nearest LINAK contract, distributor or subsidiary.
Warning!
By unauthorised opening of the system there is a risk that it may malfunction at a later date.
Spare parts
Please contact your nearest LINAK contact for information on spare parts.
Page 20 of 32
Disposal of LINAK product
As LINAK customers often ask us how our products can be disposed or scrapped we have prepared this guide that enables a
classification to different waste fractions for recycling or combustion.
Guide
We recommend our products to be disassembled as much as possible and divided into different waste groups for recycling or
combustion.
For example, waste can be sorted into metals, plastics, cable scrap, combustible material, and recoverable resources.
Some of these main groups can be further divided into subgroups; e.g. metal can be divided into steel/aluminium/copper and
plastic can be divided into ABS/PA/PE/PP.
As an example, the table below breaks down the different components in LINAK products to various recycling groups:
Product
Components
Recycling group
Columns/ Actuator :
Spindle and motor
Plastic housing
Cable
PCB boards
Scrap
Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap
Control Box :
PCB boards
Plastic housing
Electronics scrap
Plastic recycling or combustion
Handset/Control :
Plastic housing
Cable
PCB board
Plastic recycling or combustion
Cable scrap or combustion
Electronics scrap
By now almost all our casted plastic parts are supplied with an interior code for plastic type and fibre content, if any.
Main groups of disposal
Product main groups
DL20 IC / DL21 IC
DP
Metal scrap
X
Cable scrap
Electronics scrap
Plastic recycling or
combustion
X
X
X
X
X
X
X
X
SMPS
Comments
Disposal of batteries
Details regarding safe disposal of used and leaking batteries:
Batteries should be disposed in accordance with appropriate federal, state and local regulations. LINAK recommends that
used or leaking batteries are disposed through local recycling system. Please do not throw used or leaking batteries in normal
household waste or in nature. This will cause damage to the enviroment.
How to deal with leaking batteries
Leaking batteries should be disposed as described above.
If leaking batteries are discovered in the products, the batteries must be removed immediately to minimise damage to the
product. If leaking batteries are left in the product it might become defect.
It is recommended to use plastic gloves when handling leaking batteries. The contents of leaking batteries can cause chemical
burns and respiratory irritation.
If exposed to the contents of a leaking battery, please wash with soap and water. If irritation persists, please seek medical
attention. In case of eye contact, please flush eyes thoroughly with water for 15 minutes and seek medical attention.”
Page 21 of 32
Labels
Label for DL20 IC
Label for SMPS001
Label for DL21 IC
Label for SMPS002
Page 22 of 32
Label for SMPS006
DRAWING APPENDIX
DL20 IC
All measurements are without powder coating.
Version
Combination code
B (Built-in length)
[mm]
S (Stroke length)
[mm]
O (Outer profile length)
[mm]
EU
DL20xxxxxx500645
645
500
590
DL20 IC built-in length, stroke length, and outer profile length (mm)
Page 23 of 32
DL20 IC motor housing and profile dimensions (mm)
Motor housing
Bottom plate
DL20 IC dimensions (mm)
Page 24 of 32
DL20 IC Bracket options
Combination code
Bench left
DL20xxLxxSxxxxxx
Bench right
X
DL20xxRxxMxxxxxx
X
Bracket options (dimensions in mm)
Sockets
IC Master
IC Follower
Combination code
Type
DL20xxxxxMxxxxxx
IC Master
DL20xxxxxSxxxxxx
IC Follower
Socket combination
Page 25 of 32
Profile designs
Without trim ring
With trim ring
Page 26 of 32
DL21 IC
All measurements are without powder coating.
Version
Combination code
B (Built-in length)
[mm]
S (Stroke length)
[mm]
O (Outer profile length)
[mm]
EU
DL21xxxxxx650560
560
650
498
BIFMA
DL21xxxxxx665518
518
665
456
DL21 built-in length, stroke length, and outer profile length (mm)
Page 27 of 32
DL21 IC motor housing and profile dimensions (mm)
Motor housing
Bottom plate
DL21 IC dimensions (mm)
Page 28 of 32
DL21 IC Bracket options
Combination code
Bench left
DL21xxLxxSxxxxxx
Bench right
X
DL21xxRxxMxxxxxx
X
Bracket options (dimensions in mm)
Sockets
IC Master
IC Follower
Combination code
Type
DL21xxxxxMxxxxxx
IC Master
DL21xxxxxSxxxxxx
IC Follower
Socket combination
Page 29 of 32
Profile designs
Without trim rings
With trim rings
Page 30 of 32
LINAK APPLICATION POLICY
The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as
hardware, software, technical advice, etc. related to an existing or a new customer application.
LINAK products, as defined above, are applicable for a wide range of applications within the Medical, Furniture, Desk and
Industry areas. Yet, LINAK cannot know all the conditions under which LINAK products will be installed, used, and operated, as
each individual application is unique.
The suitability and functionality of the LINAK product and its performance under varying conditions (application, vibration,
load, humidity, temperature, frequency, etc.) can only be verified by testing, and shall ultimately be the responsibility of the
LINAK customer using any LINAK product.
LINAK shall be responsible solely that LINAK products comply with the specifications set out by LINAK and it shall be the
responsibility of the LINAK customer to ensure that the specific LINAK product can be used for the application in question.
Page 31 of 32
• Denmark
LINAK A/S
Group Headquarters
Tel: +45 73 15 15 15
Fax: +45 74 45 80 48
Fax (Sales): +45 73 15 16 13
www.linak.com
• Denmark
LINAK Profiles
Tel: +45 73 70 95 30
www.linak-profiles.com
• China
LINAK (Shenzhen) Actuator Systems, Ltd.
Tel: +86 755 8610 6656
Fax: +86 755 8610 6990
www.linak.cn
• Slovakia
LINAK Slovakia s.r.o.
Tel: +421 51 7563 444
Fax: +421 517563 410
www.linak.sk
• Thailand
LINAK APAC Ltd.
Tel: +66 33 265 400
www.linak.com
• USA
LINAK U.S. Inc.
Americas Headquarters
Tel: +1 502 253 5595
Fax: +1 502 253 5596
www.linak-us.com
SUBSIDIARIES
• Australia
LINAK Australia Pty. Ltd
Tel: +61 3 8796 9777
Fax: +61 3 8796 9778
www.linak.com.au
• Austria
LINAK Repräsentanz
Österreich (Wien)
Tel: +43 (1) 890 7446
Fax: +43 (1) 890 744615
www.linak.at - www.linak.hu
• Belgium
LINAK Actuator-Systems NV/SA
(Belgium & Luxembourg)
Tel: +32 (0)9 230 01 09
www.linak.be - www.fr.linak.be
• Poland
LINAK Polska
LINAK Danmark A/S (Spólka Akcyjna)
Tel: +48 22 295 09 70/22 295 09 71
www.linak.pl
• Argentina
NOVOTEC ARGENTINA SRL
Tel: 011-4303-8989/8900
Fax: 011-4032-0184
www.novotecargentina.com
• Denmark - International
LINAK International
Tel: +45 73 15 15 15
www.linak.com
• Republic of Korea
LINAK Korea Ltd.
Tel: +82 2 6231 1515
Fax: +82 2 6231 1516
www.linak.kr
• Colombia
MEM Ltda
Tel: +[57] (1) 334-7666
Fax: +[57] (1) 282-1684
www.mem.net.co
• Denmark - Sales
LINAK DANMARK A/S
Tel: +45 86 80 36 11
Fax: +45 86 82 90 51
www.linak.dk
• Russia
LINAK LLC
Tel: +7 495 780 3161
Fax: +7 495 687 1426
www.linak.ru
• India
Mechatronics Control Equipments India Pvt Ltd
Tel: +91-44-28558484, 85
www.mechatronicscontrol.com
• Finland
LINAK OY
Tel: +358 10 841 8700
www.linak.fi
• Slovakia
LINAK Slovakia s.r.o.
Tel: +421 51 7563 444
www.linak.sk
• France
LINAK FRANCE E.U.R.L
Tel: +33 (0) 2 41 36 34 34
Fax: +33 (0) 2 41 36 35 00
www.linak.fr
• Spain
LINAK Actuadores, S.L.u
Tel: +34 93 588 27 77
Fax: +34 93 588 27 85
www.linak.es
• Germany
LINAK GmbH
Tel: +49 6043 9655 0
Fax: +49 6043 9655 60
www.linak.de
• Sweden
LINAK Scandinavia AB
Tel: +46 8 732 20 00
Fax: +46 8 732 20 50
www.linak.se
• India
LINAK A/S India Liaison Office
Tel: +91 120 4531797
Fax: +91 120 4786428
www.linak.in
• Switzerland
LINAK AG
Tel: +41 43 388 31 88
Fax: +41 43 388 31 87
www.linak.ch - www.fr.linak.ch
www.it.linak.ch
• Ireland
LINAK UK Limited (Ireland)
Tel: +44 (0)121 544 2211
Fax: +44 (0)121 544 2552
+44 (0)796 855 1606 (UK Mobile)
+35 387 634 6554 (Republic of Ireland
Mobile)
www.linak.co.uk
• Italy
LINAK ITALIA S.r.l.
Tel: +39 02 48 46 33 66
Fax: +39 02 48 46 82 52
www.linak.it
• Japan
LINAK K.K.
Tel: 81-45-533-0802
Fax: 81-45-533-0803
• Brazil
LINAK Do Brasil Comércio De Atuadores Ltda. www.linak.jp
• Malaysia
Tel: +55 (11) 2832 7070
LINAK Actuators Sdn. Bhd.
Fax: +55 (11) 2832 7060
Tel: +60 4 210 6500
www.linak.com.br
Fax: +60 4 226 8901
• Canada
www.linak.my
LINAK Canada Inc.
Tel: +1 502 253 5595
Fax: +1 416 255 7720
www.linak-us.com
• China
LINAK (Shenzhen) Actuator Systems, Ltd.
Tel: +86 755 8610 6656
Fax: +86 755 8610 6990
www.linak.cn
• Czech Republic
LINAK C&S s.r.o.
Tel: +42 058 174 1814
Fax: +42 058 170 2452
www.linak.cz - www.linak.sk
DISTRIBUTORS
• Denmark - Headquarters
LINAK A/S - Group Headquarters
Tel: +45 73 15 15 15
Fax: +45 74 45 80 48
Fax (Sales): +45 73 15 16 13
www.linak.com
• Netherlands
LINAK Actuator-Systems B.V.
Tel: +31 76 5 42 44 40
www.linak.nl
• Taiwan
LINAK (Shenzhen) Actuator systems Ltd.
Taiwan Representative office
Tel: +886 2 27290068
Fax: +886 2 27290096
www.linak.tw
• Thailand
LINAK APAC Ltd.
Tel: +66 33 265 400
• Turkey
LINAK İth. İhr. San. ve Tic. A.Ş.
Tel: + 90 312 4726338
Fax: + 90 312 4726635
www.linak.com.tr
• United Kingdom
LINAK UK Limited
Tel: +44 (0)121 544 2211
Fax: +44 (0)121 544 2552
www.linak.co.uk
• USA
LINAK U.S. Inc.
Americas Headquarters
Tel: +1 502 253 5595
Fax: +1 502 253 5596
www.linak-us.com
www.linak-latinamerica.com
• New Zealand
LINAK New Zealand Ltd
Tel: +64 9580 2071
Fax: +64 9580 2072
www.linak.com.au
• Indonesia
PT. HIMALAYA EVEREST JAYA
Tel: +6 221 544 8956/221 544 8965
Fax: +6 221 619 1925
Fax (Sales): +6 221 619 4658
www.hej.co.id
• Iraq
Scan Medical Tech
Tel: +964 770 470 2202
• Israel
NetivTech LTD
Tel: +972 55-2266-535
Fax: +972 2-9900-560
www.netivtech.com
• Kingdom of Bahrain
Mechatronics Industrial Equipments
Tel: +973 17280059
Fax: +973 17910045
www.mechatronicsbh.com
• Qatar
Mechatronics Industrial Equipments
Tel: +974 44581155
Fax: +974 44689135
www.mechatronicsqatar.com
• Russia
OOO FAM
Tel: +7 812 3319333
Fax: +7 812 3271454
www.fam-drive.ru
• Singapore
Servo Dynamics Pte Ltd
Tel: +65 6844 0288
Fax (Sales): +65 6844 0070
• South Africa
Industrial Specialised Applications CC
Tel: +27 011 466 0346
www.isaza.co.za
• United Arab Emirates
Mechatronics Industrial Equipments LLC
Tel: +971 4 267 4311
Fax: +971 4 267 4312
www.mechatronics.ae
LINAK® accepts no responsibility for possible errors
or inaccuracies in catalogues, brochures, and other
material. LINAK reserves the right to change its
products without prior notice. LINAK cannot guarantee product availability and reserves the right to
discontinue the sale of any product.
The user is responsible for determining the suitability of LINAK products for a specific application. All
sales are subject to the ‘Standard Terms of Sale and
Delivery’, available on LINAK websites.
LINAK and the LINAK logotype are registered trademarks of LINAK A/S. All rights reserved.
• Norway
LINAK Norge AS
Tel: +47 32 82 90 90
www.linak.no
Page 32 of 32
Copyright © LINAK 2021.07 MA-M9-02-903-B
FACTORIES
">