Mitsubishi Electric Mr. Slim PEAD-RP GA Technical data

Mitsubishi Electric Mr. Slim PEAD-RP GA Technical data
SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS
July 2009
TECHNICAL DATA BOOK R410A
<Indoor unit>
INVERTER
[Model names]
PLA-RP·BA/BA2/BA3
PEAD-RP·JA(L)
PEA-RP·GA
PKA-RP·HAL
PKA-RP·KAL
PCA-RP·KA
PCA-RP·HA
PSA-RP·GA
<Outdoor unit>
PUHZ-RP35/50/60/71VHA4
PUHZ-RP100/125/140VKA
PUHZ-RP100/125/140YKA
PUHZ-RP200/250YKA
[Model names]
No. OCS16
CONTENTS
1. REFERENCE SERVICE MANUAL·············································2
2. SPECIFICATIONS ······································································3
3. OUTLINES AND DIMENSIONS ···············································24
4. WIRING DIAGRAM···································································44
5. REFRIGERANT SYSTEM DIAGRAM ······································58
6. PERFORMANCE CURVES ······················································63
7. CORRECTION FACTORS ························································65
8. APPLICABLE EXTENSION PIPE FOR EACH MODEL ··········66
9. AIR FLOW DATA ······································································75
10. NOISE CRITERION CURVES ··················································90
11. OPTIONAL PARTS ··································································106
kW Model
1
REFERENCE SERVICE MANUAL
For information on service, please refer to the service manual as follows.
1-1. INDOOR UNIT SERVICE MANUAL
Service
Manual No.
Model name
Service Ref.
PLA-RP35/50/60/71/100/125BA
PLA-RP71/125/140BA2
PLA-RP35/50/60/71/100/125BA#2.UK
PLA-RP71/125/140BA2.UK
PLA-RP100BA3
PLA-RP100BA3
PCA-RP50/60/71/100/125/140KA
PCA-RP50/60/71/100/125/140KA
PCA-RP71/125HA
PCA-RP71/125HA#1
PKA-RP35/50HAL
PKA-RP35/50HAL
PKA-RP60/71/100KAL
PKA-RP60/71/100KAL.TH
PSA-RP71/100/125/140GA
PSA-RP71/100/125/140GA#1
PEAD-RP35/50/60/71/100/125/140JA(L)
PEAD-RP35/50/60/71/100/125/140JA(L).UK
HWE08130
BWE08240
PEA-RP200/250/400/500GA
PEA-RP200/250/400/500GA.TH-AF
PEA-RP200/250GA.TH-AFMF
HWE0708A
Model name
Service Ref.
Service
Manual No.
PUHZ-RP35/50/60/71VHA4
PUHZ-RP100/125/140VKA
PUHZ-RP100/125/140YKA
PUHZ-RP200/250YKA
PUHZ-RP35/50/60/71VHA4
PUHZ-RP100/125/140VKA
PUHZ-RP100/125/140YKA
PUHZ-RP200/250YKA
OCH412
OCB412
OCH459
OCB459
OCH454
OCB454
OC329
OCH453
OCB453
OCH452
OCB452
OC332
1-2. OUTDOOR UNIT
2
OCH451
OCB451
SPECIFICATIONS
2
2-1. CEILING CASSETTE TYPE
Model name
Indoor unit
Outdoor unit
Capacity
Cooling
Btu/h
kW
kW
Total input
EER
Energy label class
SHF
Capacity
Heating
Btu/h
kW
kW
Total input
COP
Energy label class
Booster heater
Phase
Cycle
Voltage
Breaker size
Air flow
(Low-Medium2-Medium1-High)
Power supply
Indoor unit
kW
:
Hz
V
A
CMM
CFM
Pa
External pressure
Sound level
(Low-Medium2-Medium1-High)
dB(A)
External finish (Panel)
Dimension
Unit (Panel)
W : mm
D : mm
H : mm
W : inch
D : inch
H : inch
kg
lbs
mm
inch
CMM
CFM
dB(A)
dB(A)
Weight
Unit (Panel)
Field drain pipe O.D.
Outdoor unit
Air flow
Sound level at cooling
Sound level at heating
External finish
Dimension
W : mm
D : mm
H : mm
W : inch
D : inch
H : inch
kg
lbs
mm
inch
mm
inch
m
m
Weight
Refrigerant pipe size
Gas side O.D.
Liquid side O.D.
Height difference
Length
Refrigerant pipe length
NOTE:
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper
Lower
Upper
Heating
Lower
Cooling
limit
limit
limit
limit
D.B.
D.B.
D.B.
D.B.
Indoor
35°C, W.B. 22.5°C
19°C, W.B. 15°C
28°C
17°C
D.B.
D.B.
D.B.
D.B.
PLA-RP35BA
PUHZ-RP35VHA4
12,300
3.6(1.6-4.5)
1.07
3.36
A
0.84
14,000
4.1(1.6-5.2)
1.12
3.66
A
–
PLA-RP50BA
PUHZ-RP50VHA4
17,100
5.0(2.3-5.6)
1.55
3.23
A
0.81
20,500
6.0(2.5-7.3)
1.66
3.61
A
–
1
50
230
16
11-12-13-15
390-425-460-530
0
12-14-16-18
425-495-565-635
0
27-28-29-31
28-29-31-32
White Munsell 6.4Y 8.9/0.4
840 (950)
840 (950)
258 (35)
33-1/16 (37-3/8)
33-1/16 (37-3/8)
10-3/16 (1-3/8)
22(6)
49(13)
32
1-1/4
35
1,240
44
46
Ivory Munsell 3Y 7.8/1.1
800
300+23
600
31-1/2
11-13/16 + 7/8
23-5/8
42
93
12.7
1/2
6.35
1/4
Max. 30
Max. 50
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
46°C
-5°C
+
21°C, W.B. 15°C
-11°C, W.B. -12°C
3
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Indoor unit
PLA-RP60BA
Outdoor unit
Cooling
Capacity
Total input
Btu/h
20,500
24,200
kW
6.0(2.7-6.7)
7.1(3.3-8.1)
kW
EER
Energy label class
SHF
Heating
Capacity
Total input
23,900
27,300
8.0(3.5-10.2)
kW
1.82
2.15
3.85
3.72
A
–
–
Cycle
Hz
50
Voltage
V
230
1
A
Sound level
(Low-Medium2-Medium1-High)
25
CMM
12-14-16-18
14-16-18-21
CFM
425-495-565-635
495-565-635-740
Pa
0
0
dB(A)
28-29-31-32
28-30-32-34
External finish (Panel)
White Munsell 6.4Y 8.9/0.4
Dimension
W : mm
840 (950)
Unit (Panel)
D : mm
840 (950)
H : mm
258 (35)
W : inch
33-1/16 (37-3/8)
D : inch
33-1/16 (37-3/8)
H : inch
10-3/16 (1-3/8)
Weight
kg
23(6)
Unit (Panel)
lbs
51(13)
Field drain pipe O.D.
Air flow
mm
32
inch
1-1/4
CMM
60
CFM
2,120
Sound level at cooling
dB(A)
47
Sound level at heating
dB(A)
External finish
Weight
Gas side O.D.
Liquid side O.D.
NOTE:
Upper limit
Lower limit
Upper limit
Heating
Lower limit
W : mm
950
D : mm
330+30
H : mm
943
W : inch
37-3/8
D : inch
13 + 1-3/16
H : inch
37-1/8
kg
67
lbs
148
mm
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 50
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Cooling
48
Ivory Munsell 3Y 7.8/1.1
Dimension
Refrigerant pipe length
–
:
External pressure
Refrigerant pipe size
–
0.73
Phase
Air flow
(Low-Medium2-Medium1-High)
Outdoor unit
A
0.76
7.0(2.8-8.2)
kW
Breaker size
Indoor unit
2.09
3.40
kW
Energy label class
Booster heater
1.60
3.75
Btu/h
COP
Power supply
PLA-RP71BA
PUHZ-RP71VHA4
PUHZ-RP60VHA4
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
4
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Indoor unit
Outdoor unit
Cooling
Capacity
PLA-RP71BA2
PLA-RP100BA
PLA-RP100BA3
PUHZ-RP71VHA4
PUHZ-RP100VKA
PUHZ-RP100VKA
Btu/h
24,200
34,100
34,100
kW
7.1(3.3-8.1)
10.0(4.9-11.4)
10.0(4.9-11.4)
1.90
2.65
2.39
3.74
3.77
4.18
Total input
kW
EER
Energy label class
SHF
Heating
Capacity
A
0.74
27,300
38,200
38,200
kW
8.0(3.5-10.2)
11.2(4.5-14.0)
11.2(4.5-14.0)
kW
1.90
2.79
2.43
4.21
4.01
4.61
A
–
A
–
–
–
COP
Energy label class
Booster heater
kW
Phase
:
Cycle
Hz
50
Voltage
V
230
Breaker size
Indoor unit
–
0.74
Btu/h
Total input
Power supply
A
0.73
Air flow
(Low-Medium2-Medium1-High)
A
25
32
CMM
14-16-18-21
20-23-26-30
CFM
495-565-635-740
710-810-920-1060
Pa
0
0
dB(A)
28-30-32-34
32-34-37-40
External pressure
Sound level
(Low-Medium2-Medium1-High)
1
External finish (Panel)
White Munsell 6.4Y 8.9/0.4
Dimension
W : mm
Unit (Panel)
D : mm
840 (950)
840 (950)
H : mm
258 (35)
W : inch
D : inch
33-1/16 (37-3/8)
H : inch
10-3/16 (1-3/8)
Weight
kg
23(6)
25(6)
26(6)
Unit (Panel)
lbs
51(13)
55(13)
32
57(13)
Field drain pipe O.D.
mm
inch
Outdoor unit
Air flow
1-1/4
60
110
CFM
2,120
3,880
Sound level at cooling
dB(A)
47
49
Sound level at heating
dB(A)
48
Dimension
51
Ivory Munsell 3Y 7.8/1.1
W : mm
950
D : mm
H : mm
943
1,338
W : inch
37-3/8
41-5/16
37-1/8
kg
67
116
lbs
148
256
Gas side O.D.
mm
Liquid side O.D.
52-11/16
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
13 + 1-3/16
H : inch
Weight
NOTE:
1,050
330+30
D : inch
Refrigerant pipe length
11-3/4 (1-3/8)
CMM
External finish
Refrigerant pipe size
298 (35)
33-1/16 (37-3/8)
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Max. 50
Max. 75
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
5
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Indoor unit
Outdoor unit
Cooling
Capacity
Total input
PLA-RP125BA
PLA-RP125BA2
PLA-RP140BA2
PUHZ-RP125VKA
PUHZ-RP125VKA
PUHZ-RP140VKA
Btu/h
42,700
42,700
47,800
kW
12.5(5.5-14.0)
12.5(5.5-14.0)
14.0(6.2-15.3)
kW
EER
Energy label class
SHF
Heating
Capacity
Total input
–
A
A
0.71
0.71
0.71
47,800
47,800
54,600
14.0(5.0-16.0)
14.0(5.0-16.0)
16.0(5.7-18.0)
kW
3.86
3.50
4.32
3.63
4.00
3.70
–
A
A
–
–
–
kW
Phase
:
Cycle
Hz
50
Voltage
V
230
Breaker size
Indoor unit
4.36
3.21
kW
Energy label class
Power supply
3.67
3.41
Btu/h
COP
Booster heater
3.83
3.26
1
A
Air flow
(Low-Medium2-Medium1-High)
External pressure
Sound level
(Low-Medium2-Medium1-High)
32
22-25-28-31
22-25-28-31
24-26-29-32
CFM
780-880-990-1090
780-880-990-1090
850-920-1020-1130
Pa
0
0
0
dB(A)
34-36-39-41
34-36-39-41
36-39-42-44
External finish (Panel)
White Munsell 6.4Y 8.9/0.4
Dimension
W : mm
840 (950)
Unit (Panel)
D : mm
840 (950)
H : mm
298 (35)
W : inch
33-1/16 (37-3/8)
D : inch
33-1/16 (37-3/8)
H : inch
11-3/4 (1-3/8)
Weight
kg
25(6)
27(6)
27(6)
Unit (Panel)
lbs
55(13)
60(13)
mm
60(13)
32
inch
1-1/4
Field drain pipe O.D.
Outdoor unit
Air flow
CMM
120
CFM
4,230
Sound level at cooling
dB(A)
50
Sound level at heating
dB(A)
52
External finish
Dimension
Ivory Munsell 3Y 7.8/1.1
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
H : inch
Weight
Refrigerant pipe size
Gas side O.D.
NOTE:
116
119
lbs
256
262
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
52-11/16
kg
mm
Liquid side O.D.
Refrigerant pipe length
40
CMM
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46
D.B. -5
+
D.B. 21, W.B. 15
D.B. -20, W.B. -20
6
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Indoor unit
Outdoor unit
Cooling
Capacity
Total input
Heating
Btu/h
34,100
34,100
kW
10.0(4.9-11.4)
10.0(4.9-11.4)
kW
2.65
2.39
3.77
4.18
–
A
SHF
0.74
0.74
Total input
Btu/h
38,200
38,200
kW
11.2(4.5-14.0)
11.2(4.5-14.0)
kW
2.79
2.43
4.01
4.61
–
A
COP
Energy label class
Booster heater
kW
–
:
Cycle
Hz
50
Voltage
V
400
16
CMM
20-23-26-30
20-23-26-30
CFM
710-810-920-1,060
710-810-920-1,060
Pa
0
0
dB(A)
32-34-37-40
32-34-37-40
External pressure
Sound level
(Low-Medium2-Medium1-High)
3
A
Air flow
(Low-Medium2-Medium1-High)
External finish (Panel)
White Munsell 6.4Y 8.9/0.4
Dimension
W : mm
840 (950)
Unit (Panel)
D : mm
840 (950)
H : mm
298 (35)
W : inch
33-1/16 (37-3/8)
D : inch
33-1/16 (37-3/8)
H : inch
11-3/4 (1-3/8)
Weight
kg
25 (6)
26 (6)
Unit (Panel)
lbs
55 (13)
57 (13)
Field drain pipe O.D.
Outdoor unit
Air flow
mm
32
inch
1-1/4
CMM
110
CFM
3,880
Sound level at cooling
dB(A)
49
Sound level at heating
dB(A)
51
External finish
Dimension
Ivory Munsell 3Y 7.8/1.1
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
H : inch
52-11/16
kg
124
Weight
Refrigerant pipe size
Gas side O.D.
Liquid side O.D.
Refrigerant pipe length
NOTE:
lbs
273
mm
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
–
Phase
Breaker size
Indoor unit
PLA-RP100BA3
PUHZ-RP100YKA
EER
Energy label class
Capacity
Power supply
PLA-RP100BA
PUHZ-RP100YKA
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
7
3. Guaranteed voltage
Indoor unit
198~264V, 50Hz
Outdoor unit
342~457V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
3 phase 400V 50Hz
If optional air protect guide installed. D.B.-15
Model name
Indoor unit
PLA-RP125BA
PLA-RP125BA2
PLA-RP140BA2
Btu/h
PUHZ-RP125YKA
42,700
PUHZ-RP125YKA
42,700
PUHZ-RP140YKA
47,800
kW
12.5(5.5-14.0)
12.5(5.5-14.0)
14.0(6.2-15.3)
kW
3.83
3.67
4.36
EER
Energy label class
3.26
3.41
3.21
–
A
A
SHF
0.71
0.71
0.71
Outdoor unit
Cooling
Capacity
Total input
Heating
Capacity
Total input
Btu/h
47,800
47,800
54,600
kW
14.0(5.0-16.0)
14.0(5.0-16.0)
16.0(5.7-18.0)
kW
3.86
3.50
4.32
3.63
4.00
3.70
–
A
A
–
–
–
COP
Energy label class
Booster heater
Power supply
kW
Phase
:
Cycle
Hz
50
Voltage
V
400
Breaker size
Indoor unit
3
A
Air flow
(Low-Medium2-Medium1-High)
External pressure
Sound level
(Low-Medium2-Medium1-High)
16
CMM
22-25-28-31
22-25-28-31
24-26-29-32
CFM
780-880-990-1090
780-880-990-1090
850-920-1020-1130
Pa
0
0
0
dB(A)
34-36-39-41
34-36-39-41
36-39-42-44
White Munsell 6.4Y 8.9/0.4
External finish (Panel)
Dimension
W : mm
840 (950)
Unit (Panel)
D : mm
840 (950)
H : mm
298 (35)
W : inch
33-1/16 (37-3/8)
D : inch
33-1/16 (37-3/8)
11-3/4 (1-3/8)
H : inch
Weight
kg
25(6)
27(6)
27(6)
Unit (Panel)
lbs
55(13)
60(13)
mm
60(13)
32
inch
1-1/4
Field drain pipe O.D.
Outdoor unit
CMM
120
CFM
4,230
Sound level at cooling
dB(A)
50
Sound level at heating
dB(A)
Air flow
52
Ivory Munsell 3Y 7.8/1.1
External finish
Dimension
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
52-11/16
H : inch
Weight
Refrigerant pipe size
Gas side O.D.
NOTE:
lbs
278
132
291
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
126
mm
Liquid side O.D.
Refrigerant pipe length
kg
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
8
3. Guaranteed voltage
Indoor unit
198~264V, 50Hz
Outdoor unit
342~457V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
3 phase 400V 50Hz
If optional air protect guide installed. D.B.-15
2-2. CEILING-CONCEALED TYPE
Model name
Cooling
Indoor unit
PEAD-RP35JA(L)
PEAD-RP50JA(L)
Outdoor unit
PUHZ-RP35VHA4
PUHZ-RP50VHA4
Capacity
Total input
Btu/h
12,300
17,100
kW
3.6(1.6-4.5)
5.0(2.3-5.6)
kW
EER
Energy label class
SHF
Heating
Capacity
Total input
A
0.84
14,000
20,500
4.1(1.6-5.2)
6.0(2.5-7.3)
kW
1.10
1.56
3.73
3.85
A
A
kW
-
-
Phase
:
Cycle
Hz
50
Voltage
V
230
Breaker size
Indoor unit
A
0.85
kW
Energy label class
Power supply
1.55(1.53)
3.23(3.27)
Btu/h
COP
Booster heater
1.02(1.00)
3.53(3.60)
1
A
16
Air flow
CMM
10-12-14
12-14.5-17
(Low-Middle-High)
CFM
353-424-494
424-512-600
External pressure
Pa
Sound level
dB(A)
35/50/70/100/150
23-27-30
26-31-35
(Low-Middle-High/ 50Pa)
External finish
Galvanized sheets
Dimension
W : mm
900
D : mm
732
H : mm
250
W : inch
35-7/16
D : inch
28-7/8
H : inch
Weight
Field drain pipe O.D.
Outdoor unit
Air flow
26(25)
lbs
58(56)
inch
1-1/4
35
CFM
1,240
Sound level at cooling
dB(A)
44
Sound level at heating
dB(A)
800
D : mm
300+23
H : mm
600
31-1/2
D : inch
11-13/16 + 7/8
H : inch
23-5/8
Gas side O.D.
kg
42
lbs
93
mm
12.7
inch
1/2
mm
6.35
inch
1/4
Height difference
m
Max. 30
Length
m
Max. 50
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
W : mm
W : inch
Liquid side O.D.
Cooling
46
Ivory Munsell 3Y 7.8/1.1
Weight
NOTE:
62(60)
32
CMM
Dimension
Refrigerant pipe length
28(27)
mm
External finish
Refrigerant pipe size
9-7/8
kg
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -11°C, W.B. -12°C
9
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Cooling
Indoor unit
PEAD-RP60JA(L)
PEAD-RP71JA(L)
Outdoor unit
PUHZ-RP60VHA4
PUHZ-RP71VHA4
Capacity
Total input
Btu/h
20,500
24,200
kW
6.0(2.7-6.7)
7.1(3.3-8.1)
kW
EER
Energy label class
SHF
Heating
Capacity
Total input
A
0.83
23,900
27,300
7.0(2.8-8.2)
8.0(3.5-10.2)
kW
1.75
2.00
4.00
4.00
A
A
kW
-
-
Phase
:
Cycle
Hz
50
Voltage
V
230
Breaker size
Indoor unit
A
0.83
kW
Energy label class
Power supply
2.03(2.01)
3.50(3.53)
Btu/h
COP
Booster heater
1.60(1.58)
3.75(3.80)
1
A
25
Air flow
CMM
14.5-18-21
17.5-21-25
(Low-Middle-High)
CFM
512-636-742
618-742-883
External pressure
Pa
Sound level
dB(A)
35/50/70/100/150
25-29-33
26-30-34
(Low-Middle-High/ 50Pa)
External finish
Galvanized sheets
Dimension
W : mm
1,100
D : mm
732
H : mm
250
W : inch
43-5/16
D : inch
28-7/8
H : inch
Weight
Field drain pipe O.D.
9-7/8
kg
33(32)
lbs
73(71)
Air flow
CMM
60
60
CFM
2,120
2,120
Sound level at cooling
dB(A)
47
47
Sound level at heating
dB(A)
48
External finish
48
Ivory Munsell 3Y 7.8/1.1
Dimension
Weight
W : mm
950
950
D : mm
330+30
330+30
H : mm
943
943
W : inch
37-3/8
37-3/8
D : inch
13 + 1-3/16
13 + 1-3/16
H : inch
37-1/8
kg
Gas side O.D.
Liquid side O.D.
Refrigerant pipe length
NOTE:
Upper limit
Lower limit
Upper limit
Heating
Lower limit
148
mm
15.88
inch
5/8
15.88
5/8
mm
9.52
9.52
inch
3/8
3/8
Height difference
m
Max. 30
Max. 30
Length
m
Max. 50
Max. 50
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Cooling
37-1/8
67
lbs
Refrigerant pipe size
73(71)
32
1-1/4
mm
inch
Outdoor unit
33(32)
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
10
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Cooling
Indoor unit
PEAD-RP100JA(L)
Outdoor unit
PUHZ-RP100VKA
Capacity
34,100
42,700
47,800
kW
10.0(4.9-11.4)
12.5(5.5-14.0)
14.0(6.2-15.3)
kW
EER
Energy label class
SHF
Capacity
3.86(3.84)
4.36(4.34)
3.24(3.26)
3.21(3.23)
A
A
A
0.82
0.84
0.83
38,200
47,800
54,600
kW
11.2(4.5-14.0)
14.0(5.0-16.0)
16.0(5.7-18.0)
kW
2.72
3.50
4.04
4.12
4.00
3.96
A
A
A
-
-
-
COP
Energy label class
Booster heater
kW
Phase
:
Cycle
Hz
50
Voltage
V
230
Breaker size
Indoor unit
2.77(2.75)
3.61(3.64)
Btu/h
Total input
Power supply
PEAD-RP140JA(L)
PUHZ-RP140VKA
Btu/h
Total input
Heating
PEAD-RP125JA(L)
PUHZ-RP125VKA
1
A
32
40
Air flow
CMM
24-29-34
29.5-35.5-42
32-39-46
(Low-Middle-High)
CFM
847-1,024-1,201
1,042-1,253-1,483
1,130-1,377-1,624
External pressure
Pa
Sound level
35/50/70/100/150
dB(A)
29-34-38
33-36-40
34-38-43
(Low-Middle-High/50Pa)
External finish
Dimension
Galvanized sheets
W : mm
1,400
1,600
D : mm
732
H : mm
250
W : inch
55-1/8
D : inch
H : inch
Weight
Field drain pipe O.D.
Outdoor unit
Air flow
9-7/8
kg
41(40)
43(42)
47(46)
lbs
91(89)
95(93)
104(102)
mm
32
inch
1-1/4
CMM
110
120
CFM
3,880
4,230
Sound level at cooling
dB(A)
49
50
Sound level at heating
dB(A)
51
52
External finish
Dimension
Ivory Munsell 3Y 7.8/1.1
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
H : inch
Weight
Refrigerant pipe size
Gas side O.D.
NOTE:
116
116
119
lbs
256
256
262
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
52-11/16
kg
mm
Liquid side O.D.
Refrigerant pipe length
63
28-7/8
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46
D.B. -5
+
D.B. 21, W.B. 15
D.B. -20, W.B. -20
11
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Cooling
Indoor unit
PEAD-RP100JA(L)
Outdoor unit
Btu/h
PUHZ-RP100YKA
34,100
PEAD-RP125JA(L)
PUHZ-RP125YKA
42,700
PEAD-RP140JA(L)
PUHZ-RP140YKA
47,800
kW
10.0(4.9-11.4)
12.5(5.5-14.0)
14.0(6.2-15.3)
kW
2.77(2.75)
3.86(3.84)
4.36(4.34)
3.61(3.64)
3.24(3.26)
3.21(3.23)
A
A
A
0.82
0.84
0.83
Capacity
Total input
EER
Energy label class
SHF
Heating
Capacity
Total input
Btu/h
38,200
47,800
54,600
kW
11.2(4.5-14.0)
14.0(5.0-16.0)
16.0(5.7-18.0)
kW
2.72
3.50
4.04
4.12
4.00
3.96
A
A
A
-
-
-
COP
Energy label class
Booster heater
Power supply
kW
Phase
:
Cycle
Hz
50
Voltage
V
400
Breaker size
Indoor unit
3
A
16
Air flow
CMM
24-29-34
29.5-35.5-42
32-39-46
(Low-Middle-High)
CFM
847-1,024-1,201
1,042-1,253-1,483
1,130-1,377-1,624
External pressure
Sound level
Pa
35/50/70/100/150
dB(A)
29-34-38
33-36-40
34-38-43
(Low-Middle-High/50Pa)
External finish
Dimension
Galvanized sheets
W : mm
1,400
1,600
D : mm
732
H : mm
250
W : inch
55-1/8
D : inch
63
28-7/8
H : inch
Weight
Field drain pipe O.D.
Outdoor unit
Air flow
9-7/8
kg
41(40)
43(42)
47(46)
lbs
91(89)
95(93)
104(102)
mm
32
inch
1-1/4
CMM
110
120
CFM
3,880
4,230
Sound level at cooling
dB(A)
49
50
Sound level at heating
dB(A)
51
52
External finish
Dimension
Weight
Refrigerant pipe size
Ivory Munsell 3Y 7.8/1.1
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
H : inch
kg
124
52-11/16
126
132
lbs
273
278
291
Gas side O.D.
mm
Liquid side O.D.
Refrigerant pipe length
NOTE:
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
15.88
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
12
3. Guaranteed voltage
Indoor unit
198~264V, 50Hz
Outdoor unit
342~457V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
3 phase 400V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Indoor unit
Outdoor unit
Cooling
Capacity
65,000
75,000
kW
19.0(9.0-22.4)
22.0(11.2-28.0)
kW
6.70
8.34
2.84
2.64
EER
Energy label class
SHF
Capacity
-
0.81
0.86
76,400
92,000
kW
22.4(9.5-25.0)
27.0(12.5-31.5)
kW
6.50
8.20
3.45
3.29
-
-
COP
Energy label class
Booster heater
kW
-
-
Phase
:
Cycle
Hz
50
Voltage
V
400
Breaker size
Indoor unit
Btu/h
Total input
Power supply
PEA-RP250GA
PUHZ-RP250YKA
Btu/h
Total input
Heating
PEA-RP200GA
PUHZ-RP200YKA
3
A
Indoor 15 / Outdoor 32
Air flow
CMM
52-65
64-80
(Low-High)
CFM
1835-2295
2260-2825
External pressure
Sound level
Pa
150
dB(A)
48-51
W : mm
1400
49-52
(Low-High)
External finish
Dimension
Galvanized steel
1600
D : mm
634
H : mm
W : inch
400
55-1/8
63
D : inch
25
H : inch
Weight
15-3/4
kg
70
77
lbs
155
170
Unit drain pipe
Outdoor unit
Air flow
R1
CMM
140
CFM
4,940
Sound level at cooling
dB(A)
58
Sound level at heating
dB(A)
59
External finish
Dimension
Ivory Munsell 3Y 7.8/1.1
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
H : inch
Weight
Refrigerant pipe size
Gas side O.D.
52-11/16
kg
135
lbs
297
141
311
mm
25.4
inch
Liquid side O.D.
Refrigerant pipe length
NOTE:
9.52
inch
3/8
12.7
1/2
Height difference
m
Max. 30
Length
m
Max. 100
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
1
mm
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+1
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
13
3. Guaranteed voltage
342~457V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
3 phase 400V 50Hz
Outdoor unit
3 phase 400V 50Hz
+1. If optional air protect guide is installed : D.B.-15
Model name
Indoor unit
Outdoor unit
Cooling
Capacity
Total input
PEA-RP400GA
PEA-RP500GA
PUHZ-RP200YKA%2
PUHZ-RP250YKA%2
Btu/h
130,000
150,000
kW
38.0(18.0-44.8)
44.0(22.4-56.0)
kW
12.95
17.16
2.93
2.56
EER
Energy label class
SHF
Heating
Capacity
Total input
153,000
184,000
44.8(18.0-50.0)
54.0(25.0-63.0)
kW
12.55
16.88
3.57
3.20
-
-
kW
-
-
Phase
:
Cycle
Hz
50
Voltage
V
400
Breaker size
Indoor unit
0.77
kW
Energy label class
Power supply
-
0.75
Btu/h
COP
Booster heater
-
3
A
Indoor 15 / Outdoor 32 % 2
Air flow
CMM
120
160
(High)
CFM
4240
5650
External pressure
Sound level
Pa
150
dB(A)
52
53
(High)
External finish
Dimension
Galvanized steel
W : mm
1,947
D : mm
764
H : mm
595
W : inch
79-11/16
D : inch
30-1/8
H : inch
23-7/16
Weight
kg
130
133
lbs
286
293
Unit drain pipe
Outdoor unit
(Per 1 outdoor unit)
R1
CMM
140
CFM
4,940
Sound level at cooling
dB(A)
58
Sound level at heating
dB(A)
Air flow
59
Ivory Munsell 3Y 7.8/1.1
External finish
Dimension
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
52-11/16
H : inch
Weight
Refrigerant pipe size
Gas side O.D.
kg
135
lbs
297
mm
141
311
25.4 % 2
inch
Liquid side O.D.
Refrigerant pipe length
NOTE:
9.52 % 2
inch
3/8 % 2
12.7 % 2
1/2 % 2
Height difference
m
Max. 30
Length
m
Max. 100 (per 1 outdoor unit)
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
1%2
mm
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+1
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
14
3. Guaranteed voltage
342~457V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
3 phase 400V 50Hz
Outdoor unit
3 phase 400V 50Hz
+1. If optional air protect guide is installed : D.B.-15
2-3. WALL MOUNTED TYPE
Model name
Indoor unit
Outdoor unit
Cooling
Capacity
Total input
12,300
15,700
kW
3.6(1.6-4.5)
4.6(2.3-5.6)
kW
Energy label class
SHF
Capacity
Total input
14,000
17,100
5.0(2.5-7.3)
kW
1.13
1.38
3.63
3.62
A
A
Hz
50
Voltage
V
230
A
16
CMM
9-10.5-12
(Low-Middle-High)
CFM
320-370-425
External pressure
Pa
0
dB(A)
36-40-43
White Munsell 1.0Y 9.2/0.2
Weight
Field drain pipe I.D.
Air flow
W : mm
898
D : mm
249
H : mm
295
W : inch
35-3/8
D : inch
9-13/16
H : inch
11-5/8
kg
13
lbs
29
mm
16
inch
5/8
CMM
35
CFM
1,240
Sound level at cooling
dB(A)
44
Sound level at heating
dB(A)
External finish
Weight
Gas side O.D.
Liquid side O.D.
W : mm
800
D : mm
300+23
H : mm
600
W : inch
31-1/2
D : inch
11-13/16 + 7/8
H : inch
23-5/8
kg
42
lbs
93
mm
12.7
inch
1/2
mm
6.35
inch
1/4
Height difference
m
Max. 30
Length
m
Max. 50
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
46
Ivory Munsell 3Y 7.8/1.1
Dimension
Cooling
1
Air flow
Dimension
NOTE:
-
Cycle
External finish
Refrigerant pipe length
-
:
(Low-Middle-High)
Refrigerant pipe size
A
0.72
Phase
Sound level
Outdoor unit
A
0.81
4.1(1.6-5.2)
kW
Breaker size
Indoor unit
1.43
3.22
kW
Energy label class
Power supply
0.98
3.67
Btu/h
COP
Booster heater
PKA-RP50HAL
PUHZ-RP50VHA4
Btu/h
EER
Heating
PKA-RP35HAL
PUHZ-RP35VHA4
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -11°C, W.B. -12°C
15
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Indoor unit
Outdoor unit
Cooling
Capacity
Total input
20,500
24,200
34,100
34,100
7.1(3.3-8.1)
10.0(4.9-11.4)
10.0(4.9-11.4)
kW
1.54
1.96
2.90
2.90
3.90
3.62
3.45
3.45
A
A
A
0.78
0.73
0.73
23,900
27,300
38,200
38,200
kW
7.0(2.8-8.2)
8.0(3.5-10.2)
11.2(4.5-14.0)
11.2(4.5-14.0)
kW
1.76
2.13
3.10
3.10
3.98
3.76
3.61
3.61
A
A
A
A
-
-
-
3
Energy label class
Booster heater
Phase
kW
Cycle
Hz
50
50
Voltage
V
230
400
Breaker size
Indoor unit
A
0.86
Btu/h
COP
Power supply
PKA-RP100KAL
PUHZ-RP100YKA
6.0(2.7-6.7)
SHF
Total input
PKA-RP100KAL
PUHZ-RP100VKA
kW
Energy label class
Capacity
PKA-RP71KAL
PUHZ-RP71VHA4
Btu/h
EER
Heating
PKA-RP60KAL
PUHZ-RP60VHA4
1
:
25
A
25
Air flow
(Low-Middle-High)
CMM
18-20-22
CFM
635-705-780
External pressure
Pa
Sound level
(Low-Middle-High)
Weight
Field drain pipe I.D.
Outdoor unit
Air flow
dB(A)
Munsell 1.0Y 9.2/0.2
W : mm
1,170
D : mm
295
H : mm
365
W : inch
46-1/16
D : inch
11-5/8
H : inch
14-3/8
kg
21
lbs
46
mm
16
inch
5/8
CMM
60
110
CFM
2,120
3,880
dB(A)
47
49
Sound level at heating
dB(A)
48
51
W : mm
950
Ivory Munsell 3Y 7.8/1.1
D : mm
Weight
Gas side O.D.
Liquid side O.D.
1,050
330+30
H : mm
943
1,338
W : inch
37-3/8
41-5/16
D : inch
13 + 1-3/16
H : inch
37-1/8
kg
67
116
124
lbs
148
256
273
mm
52-11/16
15.88
inch
5/8
mm
9.52
inch
NOTE:
41-45-49
Sound level at cooling
Dimension
Refrigerant pipe length
705-810-920
39-42-45
External finish
Refrigerant pipe size
16
20-23-26
0
External finish
Dimension
32
3/8
Height difference
m
Max. 30
Max. 30
Length
m
Max. 50
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Cooling
Lower limit
Upper limit
Heating
Lower limit
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
16
3. Guaranteed voltage
198~264V, 50Hz (RP100Y: 342~457V, 50Hz)
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
V: Single phase 230V 50Hz
Y: 3phase 400V 50Hz
+ If optional air protect guide installed. D.B.-15
2-4. CEILING SUSPENDED TYPE
Model name
Indoor unit
Outdoor unit
Cooling
Capacity
Total input
PCA-RP50KA
PCA-RP60KA
PCA-RP71KA
PUHZ-RP50VHA4
PUHZ-RP60VHA4
PUHZ-RP71VHA4
Btu/h
17,100
20,500
24,200
kW
5.0(2.3-5.6)
6.0(2.7-6.7)
7.1(3.3-8.1)
kW
1.56
1.50
1.96
3.21
4.00
3.62
A
A
A
0.79
0.81
0.76
EER
Energy label class
SHF
Heating
Capacity
Total input
Btu/h
18,800
23,900
27,300
kW
5.5(2.5-6.6)
7.0(2.8-8.2)
8.0(3.5-10.2)
kW
1.52
1.94
2.21
3.62
3.61
3.62
A
A
A
-
-
-
COP
Energy label class
Booster heater
Power supply
kW
Phase
:
Cycle
Hz
50
Voltage
V
230
Breaker size
Indoor unit
Air flow
(Low-Medium2-Medium1-High)
External pressure
1
A
16
CMM
10-11-13-15
15-16-17-19
16-17-18-20
CFM
355-390-460-530
530-565-600-670
565-600-635-705
Pa
Sound level
(Low-Medium2-Medium1-High)
0
dB(A)
32-34-37-40
W : mm
960
External finish
Dimension
H : mm
230
Field drain pipe O.D.
9-1/16
kg
25
lbs
55
mm
1
35
60
CFM
1,240
2,120
Sound level at cooling
dB(A)
44
47
Sound level at heating
dB(A)
46
48
W : mm
800
330+23
Dimension
Ivory Munsell 3Y 7.8/1.1
D : mm
950
330+30
H : mm
600
943
W : inch
37-3/8
D : inch
31-1/2
13 + 7/8
13 + 1-3/16
H : inch
23-5/8
37-1/8
kg
42
67
lbs
93
148
15.88
Weight
Gas side O.D.
Liquid side O.D.
mm
12.7
inch
1/2
5/8
mm
6.35
9.52
inch
1/4
3/8
Height difference
m
Max. 30
Max. 30
Length
m
Max. 50
Max. 50
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
71
CMM
External finish
NOTE:
32
26
inch
Air flow
50-3/8
26-3/4
H : inch
Weight
1,280
37-13/16
D : inch
Refrigerant pipe length
35-37-39-41
680
W : inch
Refrigerant pipe size
33-35-37-40
White Munsell 6.4Y 8.9/0.4
D : mm
Outdoor unit
25
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+1
D.B. 21°C, W.B. 15°C
D.B. -11°C, W.B. -12°C +2
17
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+1. If optional air protect guide installed. D.B.-15°C
+2. For RP60/71 D.B. -20°C, W.B. -20°C
Model name
Indoor unit
Outdoor unit
Cooling
Capacity
PCA-RP100KA
PUHZ-RP100VKA
34,100
42,700
47,800
kW
10.0(4.9-11.4)
12.5(5.5-14.0)
14.0(6.2-15.3)
kW
2.63
3.88
4.36
3.80
3.22
3.21
A
A
A
0.77
0.72
0.71
EER
Energy label class
SHF
Capacity
Btu/h
38,200
47,800
54,600
kW
11.2(4.5-14.0)
14.0(5.0-16.0)
16.0(5.7-18.0)
kW
3.02
3.88
4.43
3.71
3.61
3.61
A
A
A
-
-
-
Total input
COP
Energy label class
Booster heater
Power supply
kW
Phase
:
Cycle
Hz
50
Voltage
V
230
Breaker size
Indoor unit
1
A
32
40
Air flow
CMM
22-24-26-28
23-25-27-29
24-26-29-32
(Low-Medium2-Medium1-High)
CFM
775-850-920-990
810-885-955-1,025
850-920-1,025-1,130
External pressure
Sound level
(Low-Medium2-Medium1-High)
Pa
0
dB(A)
37-39-41-43
External finish
Dimension
39-41-43-45
1,600
D : mm
680
H : mm
230
W : inch
63
D : inch
26-3/4
H : inch
Field drain pipe O.D.
9-1/16
kg
36
38
39
lbs
79
84
86
mm
26
inch
1
CMM
110
120
CFM
3,880
4,230
Sound level at cooling
dB(A)
49
50
Sound level at heating
dB(A)
51
Air flow
External finish
Dimension
52
Ivory Munsell 3Y 7.8/1.1
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
H : inch
Weight
Refrigerant pipe size
Gas side O.D.
NOTE:
116
119
lbs
256
262
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
52-11/16
kg
mm
Liquid side O.D.
Refrigerant pipe length
41-43-45-48
White Munsell 6.4Y 8.9/0.4
W : mm
Weight
Outdoor unit
PCA-RP140KA
PUHZ-RP140VKA
Btu/h
Total input
Heating
PCA-RP125KA
PUHZ-RP125VKA
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46
D.B. -5
+
D.B. 21, W.B. 15
D.B. -20, W.B. -20
18
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Indoor unit
PCA-RP100KA
PUHZ-RP100YKA
Outdoor unit
Cooling
Capacity
34,100
42,700
47,800
kW
10.0(4.9-11.4)
12.5(5.5-14.0)
14.0(6.2-15.3)
kW
2.63
3.88
4.36
3.80
3.22
3.21
A
A
A
0.77
0.72
0.71
EER
Energy label class
SHF
Capacity
Btu/h
38,200
47,800
54,600
kW
11.2(4.5-14.0)
14.0(5.0-16.0)
16.0(5.7-18.0)
kW
3.02
3.88
4.43
3.71
3.61
3.61
A
A
A
-
-
-
Total input
COP
Energy label class
Booster heater
Power supply
kW
Phase
:
Cycle
Hz
50
Voltage
V
400
16
Breaker size
Indoor unit
3
A
Air flow
CMM
22-24-26-28
23-25-27-29
24-26-29-32
(Low-Medium2-Medium1-High)
CFM
775-850-920-990
810-885-955-1,025
850-920-1,025-1,130
External pressure
Sound level
(Low-Medium2-Medium1-High)
0
Pa
dB(A)
37-39-41-43
Dimension
39-41-43-45
W : mm
1,600
D : mm
680
H : mm
230
W : inch
63
D : inch
26-3/4
9-1/16
H : inch
Weight
Field drain pipe O.D.
kg
36
38
39
lbs
79
84
86
26
mm
1
inch
Air flow
CMM
110
120
4,230
50
CFM
3,880
Sound level at cooling
dB(A)
49
Sound level at heating
dB(A)
51
52
Ivory Munsell 3Y 7.8/1.1
External finish
Dimension
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
52-11/16
H : inch
Weight
Refrigerant pipe size
Gas side O.D.
NOTE:
124
126
132
lbs
273
278
291
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
kg
mm
Liquid side O.D.
Refrigerant pipe length
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
41-43-45-48
White Munsell 6.4Y 8.9/0.4
External finish
Outdoor unit
PCA-RP140KA
PUHZ-RP140YKA
Btu/h
Total input
Heating
PCA-RP125KA
PUHZ-RP125YKA
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
19
3. Guaranteed voltage
Indoor unit
198~264V, 50Hz
Outdoor unit
342~457V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
3 phase 400V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Indoor unit
PCA-RP71HA
PUHZ-RP71VHA4
Outdoor unit
Cooling
Capacity
Total input
24,200
42,700
42,700
kW
7.1(3.3-8.1)
12.5(5.5-14.0)
12.5(5.5-14.0)
kW
2.21
3.88
3.88
3.21
3.22
3.22
A
A
A
0.74
0.77
0.77
Energy label class
SHF
Capacity
Total input
Btu/h
25,900
47,100
47,100
kW
7.6(3.5-10.2)
13.8(5.0-16.0)
13.8(5.0-16.0)
kW
2.23
4.05
4.05
3.41
3.41
3.41
B
B
B
-
-
COP
Energy label class
Booster heater
Power supply
kW
:
Cycle
Hz
50
50
Voltage
V
230
400
1
A
CMM
17-19
(Low-High)
CFM
600-670
Sound level
(Low-High)
0
dB(A)
34-38
W : mm
1136
44-50
Stainless steel
1520
650
H : mm
W : inch
280
44-3/4
59-7/8
D : inch
25-5/8
H : inch
Field drain pipe O.D.
1,060-1,350
Pa
D : mm
Weight
16
30-38
External finish
Dimension
3
25
Air flow
External pressure
11
kg
41
56
lbs
90
124
mm
26
inch
Outdoor unit
Air flow
1
CMM
60
120
CFM
2,120
4,230
Sound level at cooling
dB(A)
47
50
Sound level at heating
dB(A)
48
52
W : mm
950
1,050
D : mm
330+30
330+30
External finish
Dimension
Weight
Refrigerant pipe size
Gas side O.D.
Liquid side O.D.
Refrigerant pipe length
NOTE:
Ivory Munsell 3Y 7.8/1.1
H : mm
943
1,338
W : inch
37-3/8
41-5/16
D : inch
13 + 1-3/16
13 + 1-3/16
H : inch
37-1/8
kg
67
116
lbs
148
256
mm
15.88
52-11/16
126
278
15.88
inch
5/8
5/8
mm
9.52
9.52
inch
3/8
3/8
Height difference
m
Max. 30
Max. 30
Length
m
Max. 50
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
-
Phase
Breaker size
Indoor unit
PCA-RP125HA
PUHZ-RP125YKA
Btu/h
EER
Heating
PCA-RP125HA
PUHZ-RP125VKA
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
20
3. Guaranteed voltage
198~264V, 50Hz (RP125Y : 342~457V, 50Hz)
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
V: Single phase 230V 50Hz,
Y: 3 phase 400V 50Hz
+ If optional air protect guide installed. D.B.-15
2-5. FLOOR STANDING TYPE
Model name
Indoor unit
PSA-RP71GA
Outdoor unit
Cooling
PUHZ-RP71VHA4
Capacity
Total input
Btu/h
24,200
kW
7.1(3.3-8.1)
kW
2.20
EER
3.23
Energy label class
A
SHF
Heating
0.73
Capacity
Total input
Btu/h
25,900
kW
7.6(3.5-10.2)
kW
2.23
COP
3.41
Energy label class
B
Booster heater
Power supply
kW
-
Phase
:
1
Cycle
Hz
50
Voltage
V
230
Breaker size
Indoor unit
A
25
Air flow
CMM
15-18
(Low-High)
CFM
530-635
Pa
0
dB(A)
40-45
External pressure
Sound level
(Low-High)
External finish
White Munsell 0.70Y 8.59/0.97
Dimension
W : mm
Weight
Field drain pipe I.D.
Outdoor unit
Air flow
270
H : mm
1,900
W : inch
23-5/8
D : inch
10-5/8
H : inch
74-13/16
kg
43
lbs
98
mm
20
inch
13/16
CMM
60
CFM
2,120
Sound level at cooling
dB(A)
47
Sound level at heating
dB(A)
External finish
Weight
Gas side O.D.
Liquid side O.D.
Refrigerant pipe length
NOTE:
Upper limit
Lower limit
Upper limit
Heating
Lower limit
W : mm
950
D : mm
330+30
H : mm
943
W : inch
37-3/8
D : inch
13 + 1-3/16
H : inch
37-1/8
kg
67
lbs
148
mm
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 50
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Cooling
48
Ivory Munsell 3Y 7.8/1.1
Dimension
Refrigerant pipe size
600
D : mm
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
21
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Indoor unit
PSA-RP100GA
PUHZ-RP100VKA
Outdoor unit
Cooling
Capacity
34,100
42,300
47,100
kW
10.0(4.9-11.4)
12.4(5.5-14.0)
13.8(6.2-15.3)
kW
EER
Energy label class
SHF
Capacity
4.12
4.91
3.01
2.81
A
B
C
0.81
0.75
0.74
38,200
47,800
54,600
kW
11.2(4.5-14.0)
14.0(5.0-16.0)
16.0(5.7-18.0)
kW
3.28
4.11
4.97
3.41
3.41
3.22
B
B
C
-
-
-
COP
Energy label class
Booster heater
kW
Phase
:
Cycle
Hz
50
Voltage
V
230
Breaker size
Indoor unit
2.99
3.34
Btu/h
Total input
Power supply
1
A
32
CMM
24-31
26-33
27-35
(Low-High)
CFM
850-1060
920-1165
955-1240
Sound level
(Low-High)
Pa
0
dB(A)
44-49
External finish
Dimension
46-51
600
D : mm
350
H : mm
1,900
W : inch
23-5/8
D : inch
13-3/4
H : inch
Field drain pipe I.D.
74-13/16
kg
51
53
lbs
112
117
mm
20
inch
13/16
CMM
110
120
CFM
3,880
4,230
Sound level at cooling
dB(A)
49
50
Sound level at heating
dB(A)
51
Air flow
External finish
Dimension
52
Ivory Munsell 3Y 7.8/1.1
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
H : inch
Weight
Gas side O.D.
NOTE:
116
119
lbs
256
262
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Lower limit
Upper limit
Heating
Lower limit
Cooling
52-11/16
kg
mm
Liquid side O.D.
Refrigerant pipe length
47-52
White Munsell 0.70Y 8.59/0.97
W : mm
Weight
Refrigerant pipe size
40
Air flow
External pressure
Outdoor unit
PSA-RP140GA
PUHZ-RP140VKA
Btu/h
Total input
Heating
PSA-RP125GA
PUHZ-RP125VKA
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46
D.B. -5
+
D.B. 21, W.B. 15
D.B. -20, W.B. -20
22
3. Guaranteed voltage
198~264V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
Single phase 230V 50Hz
+ If optional air protect guide installed. D.B.-15
Model name
Indoor unit
Outdoor unit
Cooling
Capacity
PSA-RP100GA
PSA-RP125GA
PSA-RP140GA
PUHZ-RP100YKA
PUHZ-RP125YKA
PUHZ-RP140YKA
Btu/h
34,100
42,300
47,100
kW
10.0(4.9-11.4)
12.4(5.5-14.0)
13.8(6.2-15.3)
kW
2.99
4.12
4.91
3.34
3.01
2.81
A
B
C
0.81
0.75
0.74
Total input
EER
Energy label class
SHF
Heating
Capacity
Btu/h
38,200
47,800
54,600
kW
11.2(4.5-14.0)
14.0(5.0-16.0)
16.0(5.7-18.0)
kW
3.28
4.11
4.97
3.41
3.41
3.22
B
B
C
-
-
-
Total input
COP
Energy label class
Booster heater
Power supply
kW
Phase
:
Cycle
Hz
50
Voltage
V
400
Breaker size
Indoor unit
3
A
16
Air flow
CMM
24-31
26-33
27-35
(Low-High)
CFM
850-1,060
920-1,165
955-1,240
External pressure
Sound level
(Low-High)
Pa
0
dB(A)
44-49
External finish
Dimension
600
D : mm
350
H : mm
1,900
W : inch
23-5/8
D : inch
13-3/4
H : inch
Field drain pipe I.D.
74-13/16
kg
51
51
53
lbs
112
112
117
mm
20
inch
13/16
CMM
110
120
CFM
3,880
4,230
Sound level at cooling
dB(A)
49
50
Sound level at heating
dB(A)
51
Air flow
52
External finish
Dimension
Ivory Munsell 3Y 7.8/1.1
W : mm
1,050
D : mm
330+30
H : mm
1,338
W : inch
41-5/16
D : inch
13 + 1-3/16
H : inch
Weight
Refrigerant pipe size
Gas side O.D.
NOTE:
52-11/16
kg
124
126
132
lbs
273
278
291
mm
Liquid side O.D.
Refrigerant pipe length
47-52
White Munsell 0.70Y 8.59/0.97
W : mm
Weight
Outdoor unit
46-51
15.88
inch
5/8
mm
9.52
inch
3/8
Height difference
m
Max. 30
Length
m
Max. 75
1. Rating conditions (ISO T1)
Cooling
Indoor : D.B. 27 (80°F) W.B. 19 (66°F)
Heating
Indoor : D.B. 20 (68°F)
Refrigerant piping length (one way) : 5m (16ft.)
2. Guaranteed operating range
Upper limit
Cooling
Lower limit
Upper limit
Heating
Lower limit
Indoor
D.B. 35°C, W.B. 22.5°C
D.B. 19°C, W.B. 15°C
D.B. 28°C
D.B. 17°C
Outdoor : D.B. 35 (95°F) W.B. 24 (75°F)
Outdoor : D.B. 7 (45°F) W.B. 6 (43°F)
Outdoor
D.B. 46°C
D.B. -5°C
+
D.B. 21°C, W.B. 15°C
D.B. -20°C, W.B. -20°C
23
3. Guaranteed voltage
Indoor unit
198~264V, 50Hz
Outdoor unit
342~457V, 50Hz
4. Above data are based on the indicated voltage.
Indoor unit
Single phase 230V 50Hz
Outdoor unit
3 phase 400V 50Hz
+ If optional air protect guide installed. D.B.-15
OUTLINES AND DIMENSIONS
INDOOR UNIT
PLA-RP35BA
PLA-RP100BA
PLA-RP71BA2
Unit : mm
PLA-RP50BA
PLA-RP125BA
PLA-RP100BA3
Ceiling hole
PLA-RP125BA2
PLA-RP140BA2
20~45
860~910
810
Suspension bolt pitch
Detail connecting of branch duct(Both aspects)
90
100
100
90
Cut out hole
860~910
620
605 +35
-5
Indoor power supply
terminal block(Option part)
Ceiling hole
+
Suspension bolt pitch
840
Branch duct hole
155
Remote controller
terminal block
Indoor unit/Outdoor unit
connecting terminal block
Branch duct hole
350
:175
167
70
160
(7.5)
160
100
Fresh air
intake hole
PLA-RP71BA
130
20~45
PLA-RP60BA
20~45
3
+
14-:2.8
Burring hole pitch
Burring hole
:150
Detail drawing of fresh air intake hole
(7.5)
24
160
D
C
90
150
Cut out hole
Burring hole
840
60
284
(
Connected the attached
Drain pipe
connected to VP-25 flexible pipe or socket.
377
+
Control wire entry
B
Cut out hole
:100
Keep approximately
10 to 15mm space
between unit ceiling
and ceiling slab.
+
Ceiling
+
In case of standard grille : PLP-6BA / PLP-6BAMD
Ceiling
35
Power supply wire,
Indoor unit/Outdoor unit
connecting wire entry
+
190
156
105
+
+
+
17 +50
Suspension bolt
lower edge
140
+
50~70
170
A
2
)
158
1
Burring hole pitch
:125
120
120
160
Suspension bolt
M10 or W3/8
3-:2.8
20~45
187.5
Grille
597
Drain hole
Drain pump clean hole
and Drain emergency
drainage hole
M
597
Auto vane
(Air outlet)
switch<Cooling>and
Emergency Up/Down switch<Up>
Emergency operation
switch<Heating>and
Emergency Up/Down switch<Down>
Air intake hole
Air outlet hole
500
950
M
In case of auto-grille : PLP-6BAJ
In case of wireless remote controller : PLP-6BALM Auto grille
Air intake grille up/down discharge
Emergency operation
Air intake grille
Receiver
M
83
M
36
500
83
36
Indoor unit
1500mm
or more
1000mm
or more
Indoor unit
3000mm or more
Obstacle
Floor
Air intake grille
Vane motor
950
Grille
DEFROST/STAND BY lamp
Operation lamp
Air outlet hole
Ceiling
Ceiling
L.L Filter
1800mm or more
from floor
For high
attachment
Note 1. Please choose the grille from a standard grille, auto-grille.
2. As for drain pipe, please use VP-25(O.D. :32 PVC TUBE).
Drain pump is included.
Max. lifting height is 850mm from the ceiling.
3. As for suspension bolt, please use M10 or W3/8.
(Procured at local site)
4. Electrical box may be removed for the service purpose.
Make sure to slack the electrical wire little bit for control/ power wires connection.
5. The height of the indoor unit is able to be adjusted with the grille attached.
6. For the installation of the optional high efficiency filter or optional multi-functional casement.
1) Requires E or more space between transom and ceiling for the installation.
2) Add 135 mm to the dimensions + marked on the figure.
3) The optional high efficiency filter must be used jointly with optional multi-functional casement.
7. When installing the branch ducts, be sure to insulate adequately.
Otherwise condensation and dripping may occur.
(It becomes the cause of dew drops/water dew.)
8. As for necessary installation/service space, please refer to the left figure.
Models
PLA-RP35/50BA
PLA-RP60BA
PLA-RP71BA
PLA-RP71BA2
PLA-RP100,125BA
PLA-RP100BA3
PLA-RP125,140BA2
24
1
2
Refrigerant pipe
···:6.35
Flared connection
···1/4 inch
Refrigerant pipe
:6.35 / :9.52
Flared connection
1/4 inch/3/8 inch
(compatible)
Refrigerant pipe
···:12.7
Flared connection
···1/2 inch
Refrigerant pipe
···:9.52
Flared connection
···3/8 inch
A
B
C
D
E
80
74
241 258 87
400
Refrigerant pipe
···:15.88
Flared connection
···5/8 inch
281 298
85 77
440
Max. 4.0m
Air intake hole
Unit : mm
PEAD-RP35, 50, 60, 71, 100, 125, 140JA
2xE-:2.9
Suspension bolt hole
4-14x30 Slot
18
Air
inlet
210
G
Air
outlet
A
B(Suspension bolt pitch)
C
D (Duct)
100x(E-1)=F
15
643 (Suspension bolt pitch)
32
238
10
Terminal block
(Remote controller transmission line)
175±5mm
(Actual length)
217
250
Control box
2×2-:2.9
136
67
356
NOTE 1. Use M10 screw for the Suspension bolt (field supply).
2. Keep the service space for the maintenance at the bottom.
3. This chart indicates for PEAD-RP60•71•100•125•140JA
models,which have 2 fans. PEAD-RP35•50JA models have 1 fan.
4. In case that the inlet duct is used, remove the air filter (supplied with
the unit), then install the filter (field supply) at suction side.
Drain pipe(O.D.:32)
Terminal block
(Spontaneous draining) (Indoor/Outdoor connecting line)
Model
A
PEAD-RP35,50JA
900
PEAD-RP60,71JA
PEAD-RP100,125JA
PEAD-RP140JA
6
D
E
F
G
954 1000 860
9
800
858
B
C
1100 1154 1200 1060
1400 1454 1500 1360
1600 1654 1700 1560
11 1000 1058
14 1300 1358
16 1500 1558
J
Gas pipe Liquid pipe
:12.7
:6.35
:15.88
:9.52
Kx(L-1)=M
J
K
More than 20mm
Ceiling surface
112
112
N-:2.9
More than 10mm
Drain hose (I.D.:32)
<accessory>
11
1 Refrigerant piping
Flare connection (gas)
Less than 300mm
Less than 700mm
732
700
Drain pipe Drain pump
(O.D.:32)
41
57
178 (Duct)
100
33
23
40
122
2 Refrigerant piping
Flare connection (liquid)
23
10
58
40
57
21
20
30
100
Air Filter
Access door
Q
Make the access door at the appointed position properly for service maintenance.
P
Qx(R-1)=S
H
J
K
L
M
N
P
Q
R
S
PEAD-RP35,50JA
1000
54
260
4
780
10
40.5
273
4
819
PEAD-RP60,71JA
PEAD-RP100,125JA
PEAD-RP140JA
1200
1500
1700
49
54
54
330
320
370
4
5
5
990
1280
1480
10
12
12
40
40
40
340
330
380
4
5
5
1020
1320
1520
Model
777
50
H
Note2
Access door
50
250
~30 45
0
0
450 0
30
han
re t
Mo
Required space for service and maintenance
25
Unit : mm
PEAD-RP35, 50, 60, 71, 100, 125, 140JAL
2xE-:2.9
Suspension bolt hole
4-14x30 Slot
210
G
Air
inlet
C
Air
outlet
A
18
B(Suspension bolt pitch)
D (Duct)
100x(E-1)=F
15
21
Terminal block
(Remote controller transmission line)
732
700
32
175±5mm
(Actual length)
217
250
10
33
2×2-:2.9
1 Refrigerant piping
Flare connection (gas)
Control box
136
67
356
NOTE 1. Use M10 screw for the Suspension bolt (field supply).
2. Keep the service space for the maintenance at the bottom.
3. This chart indicates for PEAD-RP60•71•100•125•140JAL
models,which have 2 fans. PEAD-RP35•50JAL models have 1 fan.
4. In case of the inlet duct is used,remove the air filter
(supplied with the unit), then install the filter
(field supply) at suction side.
Drain pipe(O.D.:32)
Model
D
E
F
G
954 1000 860
9
800
858
A
PEAD-RP35,50JAL
900
PEAD-RP60,71JAL
PEAD-RP100,125JAL
PEAD-RP140JAL
6
B
C
1100 1154 1200 1060
1400 1454 1500 1360
1600 1654 1700 1560
11 1000 1058
14 1300 1358
16 1500 1558
J
Gas pipe Liquid pipe
:12.7
:6.35
:15.88
:9.52
Kx(L-1)=M
J
K
More than 20mm
Ceiling surface
112
112
N-:2.9
More than 10mm
Drain hose (I.D.:32)
<accessory>
Terminal block
(Indoor/Outdoor connecting line)
11
23
40
122
100
178 (Duct)
643 (Suspension bolt pitch)
57
2 Refrigerant piping
Flare connection (liquid)
23
10
58
40
57 20
30
100
Air Filter
Access door
Q
Make the access door at the appointed position properly for service maintenance.
P
Qx(R-1)=S
H
J
K
L
M
N
P
Q
R
S
PEAD-RP35,50JAL
1000
54
260
4
780
10
40.5
273
4
819
PEAD-RP60,71JAL
PEAD-RP100,125JAL
PEAD-RP140JAL
1200
1500
1700
49
54
54
330
320
370
4
5
5
990
1280
1480
10
12
12
40
40
40
340
330
380
4
5
5
1020
1320
1520
Model
777
50
H
Note2
Access door
50
250
~30 45
0
0
450 0
30
han
re t
Mo
Required space for service and maintenance
26
A
39
Drain R1
565
Left side view
Refrigerant pipe
:9.52 (3/8 braze)
Return air
Return air
sensor
50
Refrigerant pipe
10
:25.4 (1 braze)
634
530
A
Rubber bush
<Power supply wiring>
Rubber bush
<Outdoor unit
connection wiring>
Rubber bush <Remote
controller wiring>
54
10
55
376
Supply air
<Accessory>
Pipe cover···················2pcs.
(For dew condensation prevention of local piping and unit connection)
Remote controller········1pc.
330
22
145 144
130 130 35
89
35
73
262
Control box
462
40
40
155
Supply air
duct flange 45
20
42
Front view
1284
1400
1340
1260
1000
Top view
7x130(=910)
1300
130
22-: 3.1
20
34
31
Return air
duct flange
105
40
4- :12
45 <For hanging bolt M10>
[Field supply]
10
130
10
24-: 3 Holes
1102
8x130(=1040)
199
200
131
100
400
70 75 129
100 100 25
25
95
250
27
11
124
31
PEA-RP200GA
Unit : mm
A
39
50
10
A
Left side view
Drain R1
565
634
530
Return air
sensor
Rubber bush
<Power supply
wiring>
Rubber bush
<Outdoor unit
connection wiring>
54
10
55
376
Supply air
Control box
462
40
100
40
255
Supply air
duct flange 45
20
42
124
66
Front view
1484
1600
1540
1460
1000
Top view
7x130(=910)
1500
400
130
130
20
34
66
10
Return air
duct flange
205
40
4- :12
45 <For hanging bolt M10>
[Field supply]
10
26- :3 Holes
22- :3.1
1302
9X130(=1170)
199
200
131
Rubber bush <Remote
controller wiring>
Refrigerant pipe
:12.7 (1/2 braze)
Return air
Refrigerant pipe
:25.4 (1 braze)
330
22
145 144
130 130 35
89
35
73
262
70 75 129
100 100 25
25
95
250
28
11
<Accessory>
Pipe cover··················2pcs.
(For dew condensation prevention of local piping and unit connection)
Remote controller·······1pc.
PEA-RP250GA
Unit : mm
40
A
*2
A
700
Return air sensor
(2 places)
764
664
Left side view
Refrigerant pipe
39
PEA-RP400GA : :9.52 (3/8 braze)
PEA-RP500GA : :12.7 (1/2 braze)
Drain R1
[2 places (*2 part)]
Return air
*2
*1
*1
50
10
50
10
Rubber bush
<Remote controller wiring>
Refrigerant pipe :25.4 (1 braze)
[2 places (*1 part)]
120
Control box
100
149
29
Supply air
40
Supply air duct flange
20
45
395
42.5
Front view
1824
1947
1880
1800
1125
Top view
8X130(=1040)
1840
130
130
24-:3.1
36-:3 HOLES
10
280
42.5
10
1618
12X130(=1560)
40
4-:15
<For hanging bolt M12>
[Field supply]
20
Return air duct flange
33
29
203
320
141
61
Rubber bush
<Outdoor unit connection wiring>
60 60 60
570
425
59
595
Rubber bush
<Power supply wiring>
525
22
22.5
81
4X120(=480)
117 156 117
22.5
102
40
130 130
40
188
340
29
22
<Accessory>
Pipe cover··················4pcs.
(For dew condensation prevention of local piping and unit connection)
Remote controller·······1pc.
PEA-RP400, 500GA
Unit : mm
0
16
28.5
41
78.5
91
103.5
116
166
178.5
203.5
232.5
253.5
77-:5.1
Tapping
screw hole
43
394
A
56
278.3
12.5
449
C
Knockout hole for piping
372.3
356.3
327.5
43
Min.7
250mm or greater with optional
drain pump installation.
291.5
265
56
4-:9 Bolt hole
6
46
60
70
46
56
238
213
43
B
D
Mount board
Min.50
Knockout hole
for left piping
:65~:80
Knockout hole
for lower piping
273.2
231.5
128.5
153.5
21.8
0
20
32.7
53.5
66
Indoor unit outline
:65~:80
C
55
55mm or greater with left
or rear left pipng or drain
pump installation.
Left side
Min.250
Sleeve
Through hole
(purchased locally)
Min.150
Center measurement hole :2.5
0
15
0
15
6
225
200
174
58
3.8
69
125
43
125
115
140
167
180.3
193.5
70
0
59
Min.50
550mm or greater with optional
Min.220
drain pump installation.
281
197
295
8
Required space (Indoor unit)
200
225
238
265
291.5
327.5
356.3
372.3
30
449
688
898
192
612
B
Mount board
Terminal block for
MA-remote controller (option)
Emergency operation switch
(cooling/heating)
Receiver
5
A
Terminal block for power supply (option)
Terminal block for outdoor unit
Knockout hole
for right piping
249
Right side
Drain hose
:16
O.D
Refrigerant pipe : :6.35
Liquid pipe Flared connection : 1/4F
Refrigerant pipe : :12.7
Gas pipe Flared connection : 1/2F
Size
DEFROST/STAND BY lamp
169
158
184
155
Front side
Top side
Operation lamp
Knockout hole
for lower piping
Under side
457 Gas pipe 539 Liquid pipe 610 Drain hose Front side (Grille open)
599
Louver (manual)
Vane (auto)
387
PKA-RP35HAL
PKA-RP50HAL
Unit : mm
Unit : mm
PKA-RP60KAL
PKA-RP71KAL
PKA-RP100KAL
Top side
431.7
11
140.3
65.2
423.7
Left side
Right side
Front side
Mount board
365
Knockout hole
for left piping
C
74
A
(855)
295
241
5
Operation lamp
DEFROST/STAND BY lamp
1170
Receiver
Knockout hole for
right piping
Front side (Grille open)
Terminal block for outdoor unit
Terminal block for power supply (option)
Terminal block for
MA-remote controller (option)
Emergency operation switch
(cooling/heating)
30
35
444 (Gas pipe)
66
123
154
482 (Liquid pipe)
585 (Drain hose)
134
Under side
Piping connection department
Refrigerant pipe : 9.52
Flared connection : 3/8F
Gas pipe
Refrigerant pipe : 15.88
Flared connection : 5/8F
16
Drain hose
Sleeve
Through hole
(purchased locally)
75
Liquid pipe
75~ 80
O.D
Louver (manual)
Vane (auto)
B
B
54
0
Knockout hole
for lower piping
C
B
3
364
384.5
408.5
439
454
465.5
314
10
0
10
60
110
Indoor unit outline
54
32
25
77
7.8
77
87
0
0
37.5
62.5
50
75
100
117
125
142
192
67
65
77
7.8
67
25
65
Mount board
A
15.5
10.7
Center measurement hole Φ2.5
Temporarily fixing hole
314
75-Φ5.1
Tapping screw hole
454
439
408.5
384
364
Knockout hole for piping
517.4
4-Φ9 Bolt hole
60
110
65
104.5
129.5
167
217
242
279.5
292
264
292
308.5
311
Min. 220
550 mm or greater with optional
drain pump installation
Min. 50.5
108 mm or greater with left or
rear left piping or drain pump
installation
31
Wall hole for
right rear piping
585
439
449.2
Knockout hole for
rear piping
(75×480)
339
349.2
384
0
189
339
384
439
430.5
585
Min. 48
Air outlet
Min. 72.4
Wall hole for
left rear piping
Min. 250
Min. 7
265 mm or greater with optional
drain pump installation
Air inlet
530.5
7.5
R3
Required space (Indoor unit)
216.5
32
18
53
Filter hook
12.5
12.5
87.5
229.5
1
2
3
4
5
6
7
8
9
Ceiling
461
25
ø1
9
38
38
7
387
18
120°
85
260
2
8
48
233
246
When drain socket
is installed
(Drainage)
2
2
Drainage pipe connection(26mmI.D.)
Drainage pipe connection(for the left arrangement)
Knock out hole for left drain-piping arrangement
Refrigerant-pipe connection(gas pipe side/flared connection)
Refrigerant-pipe connection(liquid pipe side/flared connection)
Knock out hole for upper drain pipe arrangement
Knock out hole for fresh air intake ø100
Knock out hole for wiring arrangement 2-ø22
Knock out hole for wiring arrangement 2-ø26
Air intake
Accessory···Drain socket (I.D. 26)
Electrical box
138
86
4
Air outlet
878
853
960
917(Suspension bolt pitch)
182
140
62
80
1
In case of the rear pipe arrangement, make sure to
remove the shaded portions from the independent piece.
Then put the independent piece back in initial position.
(The heat exchanger might be clogged because of dust)
75
3
When electrical box
is pulled down
121
24
5
126
2
190
46
76
124
(71)
8
169
37
1
190
Electrical box
84 88
2
85
254
320
195
57
6
680
230
680
32
476
150
18
[FRONT VIEW]
5
10
51
184
(liquid ø6.35)
(gas ø12.7)
When drain socket
is installed
(Drainage)
NOTES.
1.Use M10 or W3/8 screw for anchor bolt.
2.Please be sure when installing the
drain pump (option parts),
refrigerant pipe will be only upward.
246
233
203
PCA-RP50KA
Unit : mm
121
37
190
46
1
2
3
4
5
6
7
8
9
461
25
ø1
9
38
7
387
18
120°
2
8
48
246
233
(Drainage)
When drain socket
is installed
138
85 86
260
2
4
2
Air outlet
1198
1173
1280
1237(Suspension bolt pitch)
182
140
62
80
1
Drainage pipe connection(26mmI.D.)
Drainage pipe connection(for the left arrangement)
Knock out hole for left drain-piping arrangement
Refrigerant-pipe connection(gas pipe side/flared connection)
Refrigerant-pipe connection(liquid pipe side/flared connection)
Knock out hole for upper drain pipe arrangement
Knock out hole for fresh air intake ø100
Knock out hole for wiring arrangement 2-ø22
Knock out hole for wiring arrangement 2-ø26
Air intake
Accessory···Drain socket (I.D. 26)
Flare nut ø6.35 (RP60 only)
Electrical box
Ceiling
38
24
5
In case of the rear pipe arrangement, make sure to
remove the shaded portions from the independent piece.
Then put the independent piece back in initial position.
(The heat exchanger might be clogged because of dust)
When electrical box
is pulled down
75
169
3
124 76
(71)
2
8
126
1
190
Electrical box
84 88
2
85
254
320
195
57
680
230
680
33
476
150
[FRONT VIEW]
6
5
10
60
179
203
A
B
246
233
71
180
200
(gas ø15.88)
When drain socket
is installed
(Drainage)
(liquid )
236
4 GAS SIDE
ø15.88
:Initial flare nut size
ø9.52
5 LIQUID SIDE ø6.35
RP60
ø9.52
ø15.88
RP71
Use the current nuts meeting the pipe size of the outdoor unit.
Available pipe size
NOTES.
1.Use M10 or W3/8 screw for anchor bolt.
2.Please be sure when installing the
drain pump (option parts),
refrigerant pipe will be only upward.
51
A
B
PCA-RP60KA
PCA-RP71KA
Unit : mm
18
34
46
190
2
1
2
3
4
5
6
7
8
9
Electrical box
461
25
ø1
9
38
7
387
18
120°
Electrical box
2
8
48
233
246
When drain socket
is installed
(Drainage)
138
260
85 86
In case of the rear pipe arrangement, make sure to
remove the shaded portions from the independent piece.
Then put the independent piece back in initial position.
(The heat exchanger might be clogged because of dust)
When electrical box
is pulled down
Ceiling
24
38
2
4
2
Drainage pipe connection(26mmI.D.)
Drainage pipe connection(for the left arrangement)
Knock out hole for left drain-piping arrangement
Refrigerant-pipe connection(gas pipe side/flared connection)
Refrigerant-pipe connection(liquid pipe side/flared connection)
Knock out hole for upper drain pipe arrangement
Knock out hole for fresh air intake ø100
Knock out hole for wiring arrangement 2-ø22
Knock out hole for wiring arrangement 2-ø26
Air intake
Accessory···Drain socket (I.D. 26)
75
3
169
37
121
1
126
190
1
Air outlet
1518
1600
1493
1557 (Suspension bolt pitch)
182
140
62
80
2
320
76
124
71
5
85
254
8
6
680
[FRONT VIEW]
680
84 88
195
230
57
476
10
5
246
233
180
200
(liquid ø9.52)
(gas ø15.88)
When drain socket
is installed
(Drainage)
236
NOTES.
1.Use M10 or W3/8 screw for anchor bolt.
2.Please be sure when installing the
drain pump (option parts),
refrigerant pipe will be only upward.
51
PCA-RP100KA
PCA-RP125KA
PCA-RP140KA
Unit : mm
150
18
1098
1136
986 <Air
outlet>
75
<gas>
<liquid>
21
110
<Air outlet>
80
70
Filter element for the exchange
model:PAC-SG38KF-E (12pcs.)
360
handle
3
or more
100
<Flexible hose(accessory)>
650
289
<Suspension bolt pitch>
320
495
<Filter contour dimension>
Filter (3-pieces)
Inspection port
(pipe sensor)
75
243
175
Suspension bolt
75
1224
<Suspension bolt pitch>
<Air intake>
NOTES.
1.Use M10 or W3/8 screw for anchor bolt.
The half bottom of FAN CASING
can be separated.
1180
102
110
258
43
197
<Air intake>
70~90
13
1
280
16
288
Electrical box
1
85
45
Rear wall
1136
Ceiling
176
105
140
18
Adjustable part
650
318
2
4
210
6
or more
366
100
38
120
165
90
Less than
254
295
7
Terminal block box
:2
22
0
:20
9
130
250
Less than
Allowing clearances
480
(122 )
8
Refrigerant-pipe connection(gas pipe side/flared connection : 5/8 inch)
Refrigerant-pipe connection(liquid pipe side/flared connection : 3/8 inch)
Flexible hose(accessory) Drainage pipe connection(26mm I.D.)
Knockout hole for behind refrigerant-piping arrangement
Knockout hole for upper refrigerant-pipe arrangement
Knockout hole for wiring arrangement : 2- : 27
Terminal block(indoor/outdoor connecting line)
Terminal block(remote controller)
Knockout hole (duct for fresh air intake): 2- : 200
· Optional parts:duct flange( : 200). model: PAC-SF28OF-E(1 pc.)
300
2
15
Less than
130
500
5
or more
90°
2~3
35
(Gap to ceiling)
Terminal block box
PCA-RP71HA
Unit : mm
Use the current nuts meeting the pipe size
of the outdoor unit.
NOTES.
1.Use M10 or W3/8 screw for anchor bolt.
The half bottom of
FAN CASING
can be separated.
<Air intake>
1482
1520
1370 <Air
outlet>
75
<liquid>
21
80
70
360
Filter element for the exchange
model:PAC-SG38KF-E (12pcs.)
handle
or more
100
<Flexible hose(accessory)>
650
289
<Suspension bolt pitch>
320
495
<Filter contour dimension>
Filter (4-pieces)
243
<gas>
Inspection port
(pipe sensor)
75
43
197
Suspension bolt
1
18
45
85
140
2
4
Rear wall
298
176
105
Adjustable part
3
254
295
110
102
110
<Suspension bolt pitch>
75
1564
165
175
<Air outlet>
<Air intake>
70~90
13
120
90
1608
1520
Ceiling
650
280
16
288
210
38
1
246
6
440
(122)
7
440
or more
100
9
250
:2
22
0
:20
Less than
Allowing clearances
Terminal block box
8
300
Electrical box
Less than
130
Refrigerant-pipe connection(gas pipe side/flared connection : 5/8 inch)
Refrigerant-pipe connection(liquid pipe side/flared connection : 3/8 inch)
Flexible hose(accessory) Drainage pipe connection(26mm I.D.)
Knockout hole for behind refrigerant-piping arrangement
Knockout hole for upper refrigerant-pipe arrangement
Knockout hole for wiring arrangement : 2- : 27
Terminal block(indoor/outdoor connecting line)
Terminal block(remote controller)
Knockout hole (duct for fresh air intake) : 2- : 200
· Optional parts:duct flange( : 200). model: PAC-SF28OF-E(1 pc.)
Less than
2
15
500
130
(Gap to ceiling)
5
90°
2~3
Terminal block box
or more
36
258
PCA-RP125HA
Unit : mm
10
10
38
controller
Front side
Knockout hole for refrigerant and drainage
90 60 oval (Provided on both sides)
235
70
600
71
250
270
180
130
Metal fixture
against overturning
530
520
260
240
370
340
125
132
15
111
Knockout hole
for branch duct
100
130 130
38
20
10
827
30
130
50
260
Knockout hole for
under-piping(120 70 oval)
Terminal block for
heater power supply 22
(Only PSH-P·GAH)
Terminal block for
indoor/outdoor
connection.
Knockout hole
for bottom fixing
95
50
Knockout hole for
wiring :27
(Provided on both sides)
Front side
Rear side
A
105
Knockout hole
for under-piping
Drain pipe
Gas pipe :15.88(5/8 inch)
Liquid pipe :9.52(3/8 inch)
Knockout hole for piping and wiring
(140 80 oval)
47
95
Electrical parts box
277
461
20
20
160
218
VIEW "A"
100
240
115
40
1900
175
123
714
766
608
216
90
767
143
55
110
Rear side
590
37
480
40
186
66
Front 1,000 or more
100 or more
1
2
300 or more
5 or more
1. Service access allows for
insertion of screw driver.
2. Adjustable
100 or more
PSA-RP71GA
Unit : mm
controller
315
Knockout hole for refrigerant and drainage
90 60 oval (Provided on both sides)
70
600
71
330
350
260
130
Metal fixture
against overturning
132
530
520
260
240
370
340
125
100
130 130
10
10
38
38
Front side
50
260
20
10
827
30
130
15
111
Knockout hole
for branch duct
Knockout hole for
95
under-piping(120 70 oval)
Knockout hole for
wiring :27 (Provided on both sides)
A
20
461
Front side
Rear side
Knockout hole
for under-piping
105
Gas pipe
40
Drain pipe
:15.88(5/8 inch)
Liquid pipe :9.52(3/8 inch)
Knockout hole for piping and wiring
(140 80 oval)
47
95
Electrical parts box
277
120
20
218
VIEW "A"
Knockout hole
for bottom fixing
Terminal block for
indoor/outdoor
connection.
Terminal block for
heater power supply
(Only PSH-P·GAH) 22
50
120
240
115
766
608
216
255
123
714
40
1900
140
767
201
77
110
261
66
Front 1,000 or more
100 or more
1. Service access allows for
insertion of screw driver.
2. Adjustable
100 or more
1
2
300 or more
5 or more
Rear side
590
38
480
PSA-RP100GA
PSA-RP125GA
PSA-RP140GA
Unit : mm
PUHZ-RP35VHA4
PUHZ-RP50VHA4
Unit : mm
400
:33 drain hole
347.5
330
300
Air intake
:33 drain hole
365
155
152
43.6
Air intake
45.4
4-10 % 21 oval hole
(M10 foundation bolt)
18
23
32.5
40
Service panel
Service panel
for charge plug
Air discharge
Handle for
moving
150
43
183
69
287.5
Connection for
gas pipe
90
10
155
300
35
600
Connection for
liquid pipe
Service port
Installation bolt pitch: 500
800
1. FOUNDATION BOLTS
Piping and wiring connection can
be made from the rear direction only.
3. ATTACHING THE CONDUIT
<Foundation bolt height>
In order to attach the conduit, it is
necessary to fix the metal plate with
2 screws to the back panel. Procure
the metal plate and make screw holes
locally. It is recommended to use the
metal plate shown below. Align the
metal plate to the marks on the unit
and attach it.
+1
18 or below
100
m
Basically open
Free space around the outdoor unit
(basic example)
100 mm or more as long as
no obstacle is placed on the
rear and right-and-left sides
of the unit.
2. PIPING-WIRING DIRECTION
Please secure the unit firmly
with 4 foundation (M10) bolts.
(Bolts, washer and nut must
be purchased locally.)
ore
or m
mm
100
FOUNDATION
mo
rm
ore
+1
+2
ore
or m
mm
500
350
mm
40
+ The position and the size of
conduit hole depend on the
conduit to be used.
20
or m
ore
2 sides should be open in
the right, left and rear side.
+ 1 In the place where short cycle tends to occur, cooling and heating
capacity and power consumption might get lowered by 10%. Air outlet
guide (optional PAC-SG58SG) will help them improve.
+ 2 If air discharges to the wall, the surface might get stained.
Holes for metal plate fixing screw
+ The size of hole depends on the
screw to be used.
39
80
Minimum installation space for outdoor unit
60
+ Conduit hole
over 100mm
over 10mm
Service space
Over10
Front piping hole
(Knockout)
Front trunking hole
(Knockout)
92
:92
40
65
45
Power supply wiring hole
(2-:27Knockout)
19
92
55
Right piping hole
(Knockout)
75
Piping Knockout Hole Details
Air Intake
500
Over
Handle for moving
Refrigerant GAS pipe connction (FLARE):15.88(5/8 inch)
Refrigerant LIQUID pipe connection (FLARE):9.52(3/8 inch)
*1...Indication of STOP VALVE connection location.
Example of Notes
over 500mm
FREE
2 SERVICE SPACE
40
:92
Over100
500
65
Right trunking hole
(Knockout)
45
92
:92
40
Side Air Intake
Handle for moving
Handle for moving
Rear Air Intake
Rear piping hole
(Knockout)
Power supply wiring hole
(2-:27Knockout)
Rear trunking hole
(Knockout)
FOUNDATION
<Foundation bolt height>
Piping and wiring connections
can be made from 4 directions:
front, right, rear and below.
Please secure the unit firmly
with 4 foundation (M10) bolts.
(Bolts and washers must be
purchased locally.)
Handle for moving
Side Air Intake
4 PIPING-WIRING DIRECTIONS
Power supply wiring hole
(2-:27Knockout)
Over
3 FOUNDATION BOLTS
943
Dimensions of space needed
for service access are
shown in the below diagram.
330
30
30
23
322
600
145
145
Earth terminal
950
Installation Feet
Air Discharge
220
175
145
Rear Air Intake
41
Drain hole
(5-:33)
71
2
1
Handle for moving
Service panel
Terminal Connections
Left···Power supply wiring
Reight···Indoor/Outdoor wiring
2-12 % 36 oval holes
(Foundation Bolt M10)
57
175
2-U Shaped notched holes
(Foundation Bolt M10)
19
370
28
Rear piping cover
Front piping cover
Bottom piping hole
(Knockout)
*1 431
over 10mm
55
27
673
The diagram below shows a
basic example.
Explantion of particular details is
given in the installation manuals etc.
73 63
23
30
55
27
63
23 27 92
73
Less than
73 63
23
473
219
40
54
53
71
40
81
417
*1 447
1 FREE SPACE (Around the unit)
PUHZ-RP60VHA4
PUHZ-RP71VHA4
Unit : mm
FREE
Over 150mm
Over 10mm
Over
10
Service space
Handle for moving
Front piping hole
(Knock-Out)
92
ø92
60
Over
500
Rear Air Intake
FOUNDATION
<Foundation bolt height>
Handle for moving
Side Air Intake
Piping and wiring connections
can be made from 4 directions:
FRONT,Right,Rear and Below.
4 PIPING-WIRING DIRECTIONS
75
55
29 92
ø92
75
92
Power supply wiring hole Power supply wiring hole
(ø27Knock-Out)
(ø40Knock-Out)
Power supply wiring hole
Power supply wiring hole Power supply wiring hole
Power supply wiring hole (ø27Knock-Out)
(ø27Knock-Out)
(ø40Knock-Out)
(ø40Knock-Out)
Right piping hole
Right trunking hole
Rear trunking hole
Front trunking hole
60 55
55 60
(Knock-Out)
(Knock-Out)
75 50
(Knock-Out)
(Knock-Out)
Piping Knock-Out Hole Details
Model
A
PUHZ-RP100~140VKA 1067
PUHZ-RP100~140YKA 919
3 FOUNDATION BOLTS
Less than
30
Dimensions of space needed Please secure the unit firmly
for service access are
with 4 foundation (M10) bolts.
shown in the below diagram. (Bolts and washers must be
purchased locally.)
2 SERVICE SPACE
1 ···Refrigerant GAS pipe connection (FLARE)ø15.88(5/8F)
2 ···Refrigerant LIQUID pipe connection (FLARE)ø 9.52(3/8F)
*1···Indication of STOP VALVE connection location.
Example of Notes
Over 1000mm
Over 10mm
63
55
73
27
26
63
92
27
73
26
2
ø9
Rear piping hole
(Knock-Out)
Side Air Intake
330
1 FREE SPACE (Around the unit)
Handle for moving
1338
Over
150
Over
500
60
632
369
45
110 160
362
225
160
160
1
Drain hole
(5-ø33)
2
60
42
81
Handle for moving
Service panel
Bottom piping hole
(Knock-Out)
Front piping cover
Rear piping cover
Air intake
Terminal connection
Left···Power supply wiring
Right···Indoor/Outdoor wiring
2-12×36 Oval holes
(Foundation Bolt M10)
56
40
0
53
2-U Shaped notched holes
(Foundation Bolt M10)
225
70
Earth terminal
1050
Air Discharge
600
Installation Feet
Rear Air Intake
28
86
The diagram below shows a
basic example.
Explantion of particular details are
given in the installation manuals etc.
63
26
73
55
27
60
A
30
26
154
19
370
417
*1 442
*1 450
41
136
PUHZ-RP100VKA
PUHZ-RP125VKA
PUHZ-RP140VKA
PUHZ-RP100YKA
PUHZ-RP125YKA
PUHZ-RP140YKA
Unit : mm
Over 10mm
Over 150mm
Service space
Over
10
Over
500
A
450
424
Front piping hole
(Knock-Out)
Front trunking hole
(Knock-Out)
Power supply wiring hole
(ø40Knock-Out)
92
ø92
75
60 55
Handle for
moving
Over
150
29
55
92
75 50
ø92
Less than
30
Right trunking hole
(Knock-Out)
75
92
55 60
Power supply wiring hole
(ø27Knock-Out)
Rear Air Intake
FOUNDATION
<Foundation bolt height>
Power supply wiring hole
(ø40Knock-Out)
Over
500
Power supply wiring hole
(ø27Knock-Out)
Right piping hole
(Knock-Out)
Power supply wiring hole
(ø27Knock-Out)
Piping Knock-Out Hole Details
ø9.52(3/8F)
ø12.7(1/2F)
2 connection
60
Model
PUHZ-RP200YKA
PUHZ-RP250YKA
1 ···Refrigerant GAS pipe connection (attached JOINT)ø25.4(Brazing locally)
2 ···Refrigerant LIQUID pipe connection (FLARE)
*1···Indication of STOP VALVE connection location.
*2···(FLARE)ø 19.05(3/4F)
Example of Notes
Over 1000mm
Over 10mm
60
3 FOUNDATION BOLTS
55
FREE
2 SERVICE SPACE
2
Rear piping hole
(Knock-Out)
ø9
Rear trunking hole
(Knock-Out)
Power supply wiring hole
(ø40Knock-Out)
Handle for
moving
Side Air Intake
Piping and wiring connections
can be made from 4 directions:
FRONT,Right,Rear and Below.
4 PIPING-WIRING DIRECTIONS
Handle for moving
Side Air Intake
1338
Dimensions of space needed Please secure the unit firmly
for service access are
with 4 foundation (M10) bolts.
shown in the below diagram. (Bolts and washers must be
purchased locally.)
60
632
369
330
30
26
1 FREE SPACE (Around the unit)
63
55
73
27
26
63
92
27
26
73
73 63
26
27
154
Rear Air Intake
160
160
1050
Earth terminal
Air Discharge
600
Installation Feet
110 160
362
225
45
136
2
42
Drain hole
(5-ø33)
1
Handle for moving
Service panel
81
Bottom piping hole
(Knock-Out)
Front piping cover
Rear piping cover
Air intake
Terminal connection
Left···Power supply wiring
Right···Indoor/Outdoor wiring
2-12×36 Oval holes
(Foundation Bolt M10)
60
Brazing
70
56
40
0
53
2-U Shaped notched holes
(Foundation Bolt M10)
225
19
370
417
28
342
*1 A
*1,*2 : 442
86
42
982
986
The diagram below shows a
basic example.
Explantion of particular details are
given in the installation manuals etc.
PUHZ-RP200YKA
PUHZ-RP250YKA
Unit : mm
Unit : mm
WIRELESS REMOTE CONTROLLER
WIRED REMOTE CONTROLLER
58
19.5
159.3
120
130
19
55
43
4
WIRING DIAGRAM
4-1. INDOOR UNIT
PLA-RP35BA
PLA-RP50BA
PLA-RP71BA2
PLA-RP100BA3
PLA-RP60BA
PLA-RP125BA2
PLA-RP71BA
PLA-RP140BA2
PLA-RP100BA
PLA-RP125BA
<Table 1> SW1 (MODEL SELECTION)
[LEGEND]
SYMBOL
I.B
CN2L
CN32
CN41
CN51
FUSE
LED1
LED2
LED3
SW1
SW2
SWE
X1
DCL
DP
FS
MF
MV
NAME
INDOOR CONTROLLER BOARD
CONNECTOR (LOSSNAY)
CONNECTOR (REMOTE SWITCH)
CONNECTOR (HA TERMINAL-A)
CONNECTOR (CENTRALLY CONTROL)
FUSE (T6.3AL250V)
POWER SUPPLY (I.B)
POWER SUPPLY (R.B)
TRANSMISSION (INDOOR-OUTDOOR)
SWITCH (MODEL SELECTION) +See table 1
SWITCH (CAPACITY CORD) +See table 2
CONNECTOR (EMERGENCY OPERATION)
RELAY (DRAIN PUMP)
REACTOR
DRAIN-UP MACHINE
DRAIN FLOAT SWITCH
FAN MOTOR
VANE MOTOR
SYMBOL
TB2
TB4
TB5,TB6
TH1
TH2
TH5
OPTION PART
W.B
BZ
LED1
LED2
RU
SW1
SW2
NAME
TERMINAL BLOCK (Indoor unit Power (option))
TERMINAL BLOCK (INDOOR/OUTDOOR CONNECTING LINE)
TERMINAL BLOCK (REMOTE CONTROLLER
TRANSMISSION LINE)
ROOM TEMP. THERMISTOR
(0 / 15k, 25 / 5. 4k DETECT)
PIPE TEMP. THERMISTOR/LIQUID
(0 / 15k, 25 / 5. 4k DETECT)
COND. / EVA. TEMP. THERMISTOR
(0 / 15k, 25 / 5. 4k DETECT)
SW1
SETTING
MODELS
PCB FOR WIRELESS REMOTE CONTROLLER
BUZZER
LED (OPERATION INDICATION : GREEN)
LED (PREPARATION FOR HEATING : ORANGE)
RECEIVING UNIT
EMERGENCY OPERATION (HEAT / DOWN)
EMERGENCY OPERATION (COOL / UP)
PLA-RP·BA
1 2 3 4 5
PLA-RP71/125BA2
1 2 3 4 5
PLA-RP140BA2
PLA-RP100BA3
1 2 3 4 5
SETTING
1 2 3 4 5
1 2 3 4 5
50
1 2 3 4 5
60
1 2 3 4 5
VANE CNV(WHT)
SW1
20 18 16 14 12 10 8 6 4 2
CN32
(WHT) 1
CN51(WHT)
Pair No.
5
CN2L
LED3
3
1
3
AUTO GRILLE
CN3G 1
(BLK)
MV
MV
ON
OFF
125
140
1 2 3 4 5
1 2 3 4 5
ON
OFF
ON
OFF
ON
OFF
ON
OFF
DCL
TRANSMISSION
WIRES
DC12V
J41 J42
SW2
19 17 15 13 11 9 7 5 3 1
M
ON
OFF
100
YLW
R.B
I.B
M
ON
OFF
The black square (■) indicates a switch position.
TB5
2
1
5
ON
OFF
1 2 3 4 5
35
Refer to tables 1 and 2
5
ON
OFF
<Table 2> SW2 (CAPACITY CODE)
SW2
CAPACITY
SETTING
CAPACITY
71
2 1
TB6
ON
OFF
WIRELESS
CN90
(WHT)
9
5
M
M
MV
MV
GRILLE
1
4
4
CNB
BZ
SW1
LED2
SW2
LED1
2 1
INDOOR/OUTDOOR
COMMUNICATION
CN3C
1
CN41(WHT)
4
(BLU)
1 2
LED1
RU
I-SEE
SENSOR
1
6
RECTIFICATION
(BLU)
MT
I-SEE SENSOR
CORNER PANEL
(OPTION PART)
1
4
4
1 2
t
t
TH2 TH5
t
TH1
1
7
FAN
CNMF
(WHT)
4
MS
3
5
M
3 1
FUSE
FS
1
CN3G
X1
1
1 D.U.M
3
CNP
(BLU)
5 3 1
TB4
YLW S1
ORN S2
S3
TO OUTDOOR
UNIT
ORN
BRN
M
3~
1~
MF
DP
CN3A
AUTOMATIC FILTER ELEVATION PANEL
(OPTION PART)
W.B
Notes:
1.SymboIs used in wiring diagram above are,
: Connector,
:
Terminal (block).
2.Indoor and outdoor connecting wires have poIarities, make
sure to match terminal numbers (S1, S2, S3) for correct wirings.
3.Since the outdoor side electric wiring may change, be sure to check
the outdoor unit electric wiring diagram for servicing.
4.This diagram shows the wiring of indoor and outdoor connecting
wires.(specification of 230V), adopting superimposed system for
power and signal.
+1:If indoor and outdoor units have separate power supplies,
refer to Fig 1.
+2:For power supply system of this unit, refer to the caution label
located near this diagram.
YLW
ORN
+ Be sure to turn off the source power
and then disconnect fan motor connector.
(Failure to do so will cause trouble in Fan motor)
U.B
3
Please set the voltage using the
remote controller.
For the setting method,please refer to
the indoor unit Installation Manual.
DC280V
REMOCON
CN22
1
SWE
(BLK)
1 3
ON OFF
AUTO GRILLE
I-SEE
FLOAT SW LIQUID/PIPE INTAKE
POWER
I-SEE SENSOR SENSOR MOTOR
CN4F
CN44
CN20
CNAC
CN4Y
CN6Y
(WHT)
(WHT)
(RED)
(WHT)
(WHT)
(RED)
9
5
LED2
OUTDOOR 1 3 5
CN01
3
+1(Fig. 1)
CN01
I.B
(BLK)
YLW
5
ORN
3
1
RED
BLU
GRN/YLW
TB2
L
N
YLW TB4
ORN S1
ORN S2
BRN
S3
I.B
1 3 INDOOR/OUTDOOR
CN3C COMMUNICATION
(BLU)
44
POWER SUPPLY
~(1PHASE)
230V 50Hz
TO OUTDOOR UNIT
45
t°
TH2 TH5
t°
1
2
3
4
CN44
TH1
SW2
SW1
SYMBOL
I.B.
CN2A
CN2L
CN32
CN41
CN51
CN90
CN105
LED1
LED2
LED3
(Red)
1
2
CN20
FS *1
1
2
3
4
CN4F
CN41
OFF
ON
LED2
CNXB2
(Red) 1
CN2L 23
4
5
CN51
CN32
1
2
CNXC2
SWE
LED1
4
3
2
1
CNXA2
(Blue)
CN22 2
(Blue) 1
(Black)
CN2A
(Red)
CN105
NAME
SYMBOL
NAME
I.B.
Indoor controller board
Indoor controller board
SW1 Switch (for mode selection)
Connector (0-10V Analog input)
SW2 Switch (for capacity code)
Connector (Lossnay)
SWE Connector (emergency operation)
Connector (Remote switch)
Connector (HA terminal-A)
Power supply board
P.B.
F01
Connector (Centrally control)
Fuse AC250V 6.3A
ZNR01, 02 Varistor
Connector (Wireless)
DSA Arrester
Connector (IT terminal)
X01
Aux. relay
LED(Power supply)
X10
Aux. relay
LED(Remote controller supply)
LED(Transmission indoor-outdoor)
SYMBOL EXPLANATION
t°
LED3
CN90
1 CN3C
3 (Blue)
I.B.
TB15
SYMBOL
TH1
TH2
TH5
ACL
FS
TB4
M
1~
Drain pump
CNP
(Blue)
X01
1 2 3 4
(Blue)
X10
F01
CND
5 (Red)
CNXC1 CNXA1
1 2
U
ZNR01
3
Fan motor
M
7 6 5 4
CNMF
1
DC280~340V
Rectifier circuit
<+A>
TO CND
TB4
1
2
TO CN3C
ACL
1
2
1
2
S1
S2
S3
L
N
TO OUTDOOR
UNIT
POWER SUPPLY
~(1PHASE)
220~240V 50Hz
(IN CASE OF CONNECT THE REPLACEMENT WIRING)
TO OUTDOOR UNIT
TO MA REMOTE
CONTROLLER
*1. Drain pump and float switch: only for PEAD-JA model
+A
S3
S1
S2
TB15
1
2
NOTE: 1. Since the outdoor side electric wiring may change be sure to
NAME
Intake air temp. Thermistor
check the outdoor unit electric wiring for servicing.
Pipe temp. Thermistor/liquid
2. Indoor and outdoor connecting wires are made with polarities,
Cond./eva.temp. Thermistor
make wiring matching terminal numbers (S1,S2,S3).
AC reactor (Power factor improvement)
Float switch
3. Symbols used in wiring diagram above are, terminal block,
Terminal block
connector.
(Indoor/outdoor connecting line)
Terminal block
(Remote controller transmission line)
*1
1 2 3 4 5
CNXB1
3
1
DSA
ZNR02
U
1
2
P.B.
1
2
1
ACL
INSIDE SECTION OF CONTROL BOX
PEAD-RP35JA(L) PEAD-RP50JA(L) PEAD-RP60JA(L) PEAD-RP71JA(L)
PEAD-RP100JA(L) PEAD-RP125JA(L) PEAD-RP140JA(L)
POWER SUPPLY
3N~PE
380/400/415V
50Hz
PE
N
1
2
TB5
TB2
RED
L1
WHITE
L2
BLACK
L3
RED
46
REMOTE
CONTROLLER
BOARD
TB6
LCD
REMOTE CONTROLLER
CIRCUIT BREAKER
(FIELD SUPPLY)
PEA-RP200,250GA:15A
BLACK
INDOOR UNIT
WHITE
2 1
CN3C
3 1
LED3
LED2
LED1
TAB1
CN2S
CNSK
1
1
DC
3
2 13.1V
3
1
CN32
2
3
1
2 CN31
3
CN51
1
CND
3
2
1
3
2
1
C02
(3P)
(Hi)
CNDK
1
CN20
2
1
CN21
2
7
52F
Lo
5
X1
3
FAN
CR2 52F
Hi
1
X4 X5 X6
X4 X5 X6
X1
5
4
C01
51F
TB4
S1
S2
S3
49F
CR1 X1
SWE
ON
OFF
SW2
TH5
TH2
TH1
1
1 2 3 4 5
ON
2 CN41
OFF
3
INDOOR
4 CONTROLLER SW1
1 2 3 4 5
BOARD
1
ON
CN29
OFF
2
MF1
3 1
C01
(6P)
(Lo)
FUSE
52F
Hi
ZNR
52F
Lo
5 4 3 2 1
INDOOR
POWER BOARD
FB
CN2D
DC13.1V
1
2
3
4
5 CN90
6
7
8
9
1 CN22
2
1 CN2L
2
DSR DSA
ZNR5~7
SNB BOARD 1
51F
TERMINAL BLOCK
NAME
NAME
FAN MOTOR (INDOOR)
OVER CURRENT RELAY (INDOOR FAN MOTOR)
MAGNETIC CONTACTOR (INDOOR FAN MOTOR<LOW SPEED>)
MAGNETIC CONTACTOR (INDOOR FAN MOTOR<HIGH SPEED>)
INTERNAL THERMOSTAT (INDOOR FAN MOTOR)
TERMINAL BLOCK
ROOM TEMP.
THERMISTOR
LIQUID PIPE TEMP.
COND./EVA. TEMP.
AUXILIARY RELAY
SURGE KILLER
FERRITE CORE
FUSE (T6.3AL250V)
VARISTOR
AUXILIARY RELAY
SWITCH (MODEL SELECTION)
SWITCH (CAPACITY CODE)
CONNECTOR (EMERGENCY OPERATION)
LED (POWER SUPPLY)
LED (POWER SUPPLY<REMOTE CONTROLLER>)
LED (TRANSMISSION<INDOOR·OUTDOOR>)
CONNECTOR (LOSSNAY)
CONNECTOR (DRAIN SENSOR)
CONNECTOR (REMOTE SWITCH)
CONNECTOR (HA TERMINAL-A)
CONNECTOR (CENTRALLY CONTROL)
CONNECTOR (WIRELESS REMOTE CONTROLLER)
VARISTOR
ARRESTER
TO OUTDOOR UNIT
CONNECTING WIRES
(POLAR)
OUTDOOR UNIT
Caution,
1. To protect fan motor from abnormal current, overcurrent relays are installed.
Therefore, do not change factory set value of overcurrent relays.
Note:1. The dotted lines show field wiring.
2. Color of earth wire is yellow and green twisting.
3. Specification subject to change without notice.
4. Indoor and outdoor connecting wires have polarities, make sure
to match wiring and terminal.
5. Emergency operation
If a trouble occurs with either the remote controller or the indoor microcomputer and no other trouble exists, emergency operation for cooling or heating
can be performed by changing the setting of connector (SWE) "ON" on the
indoor controller board.
SWE :ON / Indoor fan is running at high speed.
6. mark is connector. mark is terminal.
SYMBOL
TB6
REMOTE CONTROLLER
SYMBOL
MF1
51F
52FLo
52FHi
49F
TB2,4,5
TH1
TH2
TH5
X1
CR1,2
FB
FUSE
ZNR
X4-6
SW1
SW2
SWE
INDOOR
LED1
CONTROLLER
LED2
BOARD
LED3
CN2L
CN31
CN32
CN41
CN51
CN90
SNB
ZNR5~7
BOARD 1 DSA,DSR
INDOOR UNIT
PEA-RP200, 250GA
POWER SUPPLY
3N~PE
380/400/415V
50Hz
1
2
TB5
CR
GREEN/YELLOW
RED
WHITE
BLACK
BLUE
TB2
L1
L2
L3
N
REMOTE
CONTROLLER
BOARD
LCD
TB6
REMOTE CONTROLLER
PE
CIRCUIT BREAKER
(FIELD SUPPLY)
PEA-RP400,500GA:15A
FUSE
FB12
3
2
1
C01
MF1
47
2 1
TAB1
CN2S
CNSK
1
1
DC
3
2 13.1V
(No.2)
CND
CNDK
X1
5
3
1
CN3C
3 1
3
LED3 ZNR
1
CND
SW2
TH1-2
TH2-2
TH5-2
FAN
CNDK
7
X2
5
3
1
ON
OFF
ON
OFF
S1
S2
S3
TB4-1
S1
S2
S3
TB4-2
SWE
ON
OFF
FAN
X4 X5 X6
LED1
LED2
1 CN20
X4 X5 X6
2
3 1
7
ON
OFF
SWE
ON
OFF
1
1 2 3 4 5
2 CN41
3
INDOOR
4
CONTROLLER 1 2SW1
3 4 5
1 CN29 BOARD
(No.2)
2
FB22
3 1
X4 X5 X6
1 CN20
X4 X5 X6
2
1 CN21
2
1 CN21
2
FUSE
1
SW2
3
2
ON
OFF
C02
1
1
1 2 3 4 5
2 CN41
3
INDOOR
SW1
4
CONTROLLER 1 2 3 4 5
1 CN29 BOARD
(No.1)
2
1
2 CN32
3
1
2 CN31
3
CN51
5 4 3 2 1
INDOOR
FB21 POWER
BOARD
CN2D
DC13.1V
1
2
3
4
5 CN90
6
7
8
9
1 CN22
2
TAB1
CN2S
CNSK
1 DC
1
3
2 13.1V
(No.1)
3
LED3 ZNR
LED2
LED1
1
2 CN32
3
1
2 CN31
3
CN3C
3 1
FB11 INDOOR
POWER BOARD
CN2D
DC13.1V
1 CN2L
2
2 1
1
2
3
4
5 CN90
6
7
8
9
1 CN22
2
CN51
5 4 3 2 1
TH5-1
TH2-1
1 CN2L
2
51F
TH1-1
DSR DSA
ZNR5~7
SNB BOARD 1
52F
49F 51F
X01 X02
BLACK
WHITE
RED
5
52F
C01 4
INDOOR UNIT
TO OUTDOOR UNIT
CONNECTING WIRES
(POLAR)
TERMINAL BLOCK
NAME
REMOTE CONTROLLER
SYMBOL
NAME
TB6
TERMINAL BLOCK
OUTDOOR UNIT
SYMBOL
TB3,TB8
FUSE (T6.3AL250V)
VARISTOR
AUXILIARY RELAY
SWITCH (MODEL SELECTION)
SWITCH (CAPACITY CORD)
CONNECTOR (EMERGENCY OPERATION)
LED (POWER SUPPLY)
LED (POWER SUPPLY<REMOTE CONTROLLER>)
LED (TRANSMISSION<INDOOR·OUTDOOR>)
CONNECTOR (LOSSNAY)
CONNECTOR (DRAIN SENSOR)
CONNECTOR (REMOTE SWITCH)
CONNECTOR (HA TERMINAL-A)
CONNECTOR (CENTRALLY CONTROL)
CONNECTOR (WIRELESS REMOTE CONTROLLER)
VARISTOR
ARRESTER
NAME
FAN MOTOR (INDOOR)
OVER CURRENT RELAY (INDOOR FAN MOTOR)
MAGNETIC CONTACTOR (INDOOR FAN MOTOR)
INTERNAL THERMOSTAT (INDOOR FAN MOTOR)
TERMINAL BLOCK
ROOM TEMP.
THERMISTOR
LIQUID PIPE TEMP.
COND./EVA. TEMP.
AUXILIARY RELAY
SURGE KILLER
FERRITE CORE
Caution,
1.To protect fan motor from abnormal current, overcurrent relays are installed.
Therefore, do not change factory set value of overcurrent relays.
Note:1. The dotted lines show field wiring.
2. Color of earth wire is yellow and green twisting.
3. Specification subject to change without notice.
4. Indoor and outdoor connecting wires have polarities, make sure to
match wiring and terminal.
5. Emergency operation
If a trouble occurs with either the remote controller or the indoor microcomputer and no other trouble exists, emergency operation for cooling or heating
can be performed by changing the setting of connector (SWE) "ON" on the
indoor controller board.
SWE :ON / Indoor fan is running at high speed.
6. mark is connector. mark is terminal.
OUTDOOR UNIT
(No.2)
(No.1)
OUTDOOR UNIT
TO OUTDOOR UNIT
CONNECTING WIRES
(POLAR)
INDOOR UNIT
SYMBOL
MF1
51F
52F
49F
TB2,4-1,4-2,5
TH1-1,1-2
TH2-1,2-2
TH5-1,5-2
X1,2
CR
FB11,FB12
FB21,FB22
FUSE
ZNR
X4-6
SW1
SW2
SWE
LED1
INDOOR
CONTROLLER LED2
LED3
BOARD
CN2L
CN31
CN32
CN41
CN51
CN90
SNB
ZNR5~7
BOARD 1 DSA,DSR
PEA-RP400, 500GA
PKA-RP35HAL PKA-RP50HAL
[Explanation of symbols]
Symbol
I.B
CN2L
CN32
CN41
CN51
CN90
FUSE
LED1
LED2
LED3
SW1
SW2
SWE
X1
CNP
Name
Indoor controller board
Connector (LOSSNAY)
Connector ( Remote switch)
Connector (HA terminal-A)
Connector (Centrally control)
Connector (Remote operation adapter)
FUSE(T3.15AL250V)
Power supply (I.B)
Power supply (R.B)
Transmission (Indoor-outdoor)
Switch (Model selection) +See table 1
Switch (Capacity code) +See table 2
Connector (Emergency operation)
Relay (Drain pump (option))
Drain pump (option) power supply
(Drain pump (option))
CN4F
R.B
TB6
Drain float switch (Drain pump (option))
Wired remote controller(option)
Terminal block (Remote controller transmission line)
Symbol
M
MS
S.W
SWE2
TB2
TB4
TB5
TH1
Name
Vane motor
Fan motor
Switch board
Emergency operation
Terminal block(Indoor unit Power (option))
Terminal block (Indoor/outdoor connecting line)
Terminal block (Remote controller transmission line(option))
Room temp. Thermistor
(0/15kΩ, 25/5.4kΩ Detect)
TH2
Pipe temp. Thermistor/liquid
(0/15kΩ, 25/5.4kΩ Detect)
TH5
Cond./eva. temp. Thermistor
(0/15kΩ, 25/5.4kΩ Detect)
Pcb for wireless remote controller
LED (Operation indication : Green)
LED (Preparation for heating: Orange)
Receiving unit
REACTOR
DRAIN PUMP (OPTION)
DRAIN FLOAT SWITCH (OPTION)
W.B
LED1
LED2
REC1
DCL
D
P
DP
FS
MS
3~
<Table 1>
SW1
(MODEL SELECTION)
DCL
I.B
CNMF
6
(WHT) FUSE
1
T11
SWE
DB1
LED3
X1
LED2
1
Refer to
tables
1and 2
1 2
CN2L
(RED)
1
CN151
(WHT)
5
9
CN90
(WHT)
1
CN20
(RED)
1 2
CN41
(WHT)
1
CN44
(WHT)
4
4
YLW
1 CN32 3
(WHT)
BLK
1
1
5
CN51
(WHT)
CN4F
(WHT)
CNRU
(WHT)
TB4
YLW
S1
ORN
S2
S3
SETTING
1 2 3 4 5
TO
OUTDOOR
UNIT
MODELS
M
1~
ORN
BRN
2
LDSWE(B) SWE2
1 2 3 4 5
RP50
RU
LD101(B) REC1
SETTING
1 2 3 4 5
RP35
S.W
W.B
6
ON
OFF
<Table 2>
SW2 (CAPACITY CODE)
DP
3
1
CNP(BLU)
CN3C 3
(BLU) 1
LDSWE(A)
(BLU)
YLW
ORN
CN01
(BLK)
LED1
ON
OFF
1
3
5
ON
OFF
ON
OFF
The black square (■) indicates a switch position.
R.B
BLU
4
CN22 1
(BLU) 2
LED1
BLU
LED2
1
2
TB6
1
2
TB5
(OPTION PARTS)
M
t
○
t
○
TH1
t
TH2 TH5
○
When attaching
When attaching drain
drain pump(option), pump (option)
remove the jumper
1
4
connector CN4F
FLOAT SW
CN4F
and fit the drain
(WHT)
FS
float switch (FS).
+1(Fig. 1)
CN01
I.B
(BLK)
1
3
5
YLW
ORN
Notes:
1. SymboIs used in wiring diagram above are,
: Connector,
: Terminal (block).
I.B
2. Indoor and outdoor connecting wires have poIarities, make sure to match terminal
numbers (S1, S2, S3) for correct wirings.
1 3
3. Since the outdoor side electric wiring may change, be sure to check the outdoor unit
CN3C(BLU)
electric wiring diagram for servicing.
4. This diagram shows the wiring of indoor and outdoor connecting wires. (specification of
230V), adopting superimposed system for power and signal.
+1: If indoor and outdoor units have separate power supplies, refer to Fig. 1.
+2: For power supply system of this unit, refer to the caution label located near this diagram.
48
RED
BLU
GRN/YLW
YLW
ORN
ORN
BRN
TB2
L
N
POWER SUPPLY
~(1PHASE)
230V 50Hz
TB4
S1
S2
S3
INDOOR/OUTDOOR
COMMUNICATION
TO OUTDOOR
UNIT
PKA-RP60KAL PKA-RP71KAL PKA-RP100KAL
[LEGEND]
SYMBOL
I.B
CN2L
CN32
CN41
CN51
CN90
FUSE
LED1
LED2
LED3
SW1
SW2
SWE
X1
CNP
CN4F
R.B
TB6
NAME
Indoor controller board
Connector (LOSSNAY)
Connector (Remote switch)
Connector (HA terminal-A)
Connector (Centrally control)
Connector (Remote operation adapter)
FUSE (T3.15AL250V)
Power supply (I.B)
Power supply (R.B)
Transmission (Indoor-outdoor)
Switch (Model selection) +See table 1
Switch (Capacity code) +See table 2
Connector (Emergency operation)
Relay (Drain pump(option))
Drain pump (option) power supply
(Sold separately:Drain pump(option))
Drain float switch (Sold separately:Drain pump (option))
Wired remote controller
Terminal block (Remote controller transmission line)
SYMBOL
M
MS
S.W
SWE2
TB2
TB4
TB5
TH1
TH2
TH5
W.B
LED1
LED2
REC1
DCL
DP
FS
NAME
Vane motor
Fan motor
Switch board
Emergency operation
Terminal block (Indoor unit Power (option))
Terminal block (Indoor/outdoor connecting line)
Terminal block (Remote controller transmission line)
Room temp. Thermistor
(0 / 15k, 25 / 5. 4k Detect)
Pipe temp. Thermistor/liquid
(0 / 15k, 25 / 5. 4k Detect)
Cond. / eva. temp. Thermistor
(0 / 15k, 25 / 5. 4k Detect)
Pcb for wireless remote controller
LED (Operation indication : Green)
LED (Preparation for heating : Orange)
Receiving unit
REACTOR
DRAIN PUMP (OPTION)
DRAIN FLOAT SWITCH (OPTION)
MF
+1(Fig. 1)
CN01
I.B
(BLK)
YLW
1
ORN
3
5
INDOOR/OUTDOOR
COMMUNICATION
The black square (■) indicates a switch position.
Notes:
1. SymboIs used in wiring diagram above are,
:Connector,
: Terminal (block).
2. Indoor and outdoor connecting wires have poIarities, make sure to match terminal numbers
(S1, S2, S3) for correct wirings.
3. Since the outdoor side electric wiring may change, be sure to check the outdoor unit electric
wiring diagram for servicing.
4. This diagram shows the wiring of indoor and outdoor connecting wires.(specification of 230V),
adopting superimposed system for power and signal.
+1 If indoor and outdoor units have separate power supplies, refer to Fig 1.
+2 For power supply system of this unit, refer to the caution label located near this diagram.
49
TB2
L
N
YLW TB4
ORN S1
ORN S2
BRN
S3
I.B
1 3
CN3C (BLU)
RED
BLU
GRN/YLW
POWER SUPPLY
~(1PHASE)
230V 50Hz
TO OUTDOOR
UNIT
PCA-RP50KA PCA-RP60KA
PCA-RP100KA PCA-RP125KA
PCA-RP71KA
PCA-RP140KA
[ LEGEND]
SYMBOL
I.B
CN2L
CN32
CN41
CN51
FUSE
LED1
LED2
LED3
SW1
SW2
SWE
X1
R.B
DCL
MF
MV
TB2
NAME
INDOOR CONTROLLER BOARD
CONNECTOR (LOSSNAY)
CONNECTOR (REMOTE SWITCH)
CONNECTOR (HA TERMINAL-A)
CONNECTOR (CENTRALLY CONTROL)
FUSE (T6.3AL250V)
POWER SUPPLY (I.B)
POWER SUPPLY (R.B)
TRANSMISSION (INDOOR-OUTDOOR)
SWITCH (MODEL SELECTION) + See table 1
SWITCH (CAPACITY CODE) + See table 2
CONNECTOR (EMERGENCY OPERATION)
RELAY (DRAIN PUMP)
WIRED REMOTE CONTROLLER BOARD
REACTOR
FAN MOTOR
VANE MOTOR
TERMINAL BLOCK (Indoor unit Power (optional parts))
SYMBOL
TB4
TB5,TB6
NAME
TERMINAL BLOCK (INDOOR/OUTDOOR CONNECTING LINE)
TERMINAL BLOCK (REMOTE CONTROLLER
TRANSMISSION LINE)
ROOM TEMP. THERMISTOR
(0°C / 15kΩ, 25°C / 5. 4kΩ DETECT)
PIPE TEMP. THERMISTOR/LIQUID
(0°C / 15kΩ, 25°C / 5. 4kΩ DETECT)
COND. / EVA. TEMP. THERMISTOR
(0°C / 15kΩ, 25°C / 5. 4kΩ DETECT)
TH1
TH2
TH5
OPTIONAL PARTS
W.B
BZ
LED1
LED2
RU
SW1
SW2
DP
FS
PCB FOR WIRELESS REMOTE CONTROLLER
BUZZER
LED (OPERATION INDICATION : GREEN)
LED (PREPARATION FOR HEATING : ORANGE)
RECEIVING UNIT
EMERGENCY OPERATION (HEAT / DOWN)
EMERGENCY OPERATION (COOL / UP)
DRAIN LIFT UP MECHANISM
DRAIN FLOAT SWITCH
Refer to tables 1 and 2
DCL
TB5
2
1
TRANSMISSION
WIRES
DC12V
2 1
TB6
YLW
R.B
I.B
VANE CNV (WHT)
SW1
20 18 16 14 12 10 8 6 4 2
J41 J42
SW2
19 17 15 13 11 9 7 5 3 1
Pair No.
CN32
(WHT) 1
CN51 (WHT)
5
CN2L
LED3
LED2
1
4
1 2
INDOOR/OUTDOOR
COMMUNICATION
CN3C
(BLU)
REMOCON
CN22
(BLU)
1
SWE
OUTDOOR 1 3 5
CN01
(BLK)
1 3
CN41 (WHT)
2 1
LED1
3
DC311~339V
RECTIFICATION
ON OFF
WIRELESS
CN90
(WHT)
1
FLOAT SW
CN4F
(WHT)
9
1
LIQUID/PIPE INTAKE
CN44
CN20
(WHT)
(RED)
4
1 2
t°
t°
TH2 TH5
t°
TH1
1
4
FUSE
7
FAN
CNMF
(WHT)
4
MS
9
CNB
5
M
MV
BZ
SW1
LED2
SW2
LED1
When attaching
drain pump
(optional parts),
remove the jumper
connector CN4F
and fit the drain
float switch (FS).
RU
W.B
(OPTIONAL PARTS)
When attaching
drain pump
(optional parts)
FLOAT SW
CN4F
(WHT)
1
4
FS
3~
CN01
(BLK)
5
3
1
I.B
YLW
YLW
ORN
TB2
RED
L
BLU
N
GRN/YLW
YLW TB4
ORN S1
ORN S2
BRN
S3
I.B
1 3 INDOOR/OUTDOOR
CN3C COMMUNICATION
(BLU)
1 2 3 4 5
POWER SUPPLY
~(1PHASE)
230V 50Hz
1 D.U.M
3
CNP
(BLU)
TO OUTDOOR
UNIT
ORN
BRN
M
1~
+Be sure to turn off the source power
and then disconnect fan motor connector.
(Failure to do so will cause trouble in Fan motor)
SW1
Service
DCL
1
TB4
YLW S1
ORN S2
S3
DP
MF
(OPTIONAL PARTS)
<Table 1> SW1
(MODEL SELECTION)
+ 1 (Fig. 1)
YLW
ORN
X1
<Table 2> SW2 (CAPACITY CODE)
SW2
MODELS
Service
MODELS
PCA-RP50KA
ON
OFF
PCA-RP60KA
PCA-RP71KA
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
ON PCA-RP100KA
OFF
ON PCA-RP125KA
OFF
ON PCA-RP140KA
OFF
Service
1 2 3 4 5
1 2 3 4 5
1 2 3 4 5
ON
OFF
ON
OFF
ON
OFF
The black square (■) indicates a switch position.
TO OUTDOOR UNIT
Notes: 1. SymboIs used in wiring diagram above are,
:Connector,
:Terminal (block).
2. Indoor and outdoor connecting wires are made with poIarities,
make wiring matching terminal numbers (S1, S2, S3).
3. Since the outdoor side electric wiring may change, be sure to
check the outdoor unit electric wiring for servicing.
4. This diagram shows the wiring of indoor and outdoor connecting
wires (specification of 230V), adopting superimposed system
for power and signal.
+ 1: If indoor and outdoor units have separate power supplies,
refer to Fig. 1.
+ 2: For power supply system of this unit, refer to the caution
label located near this diagram.
50
PCA-RP71HA
[LEGEND]
SYMBOL
P. B
I. B
FUSE
CN2L
CN32
CN41
CN51
LED1
LED2
LED3
X1
X4
X5
X6
SW1
SW2
PCA-RP125HA
NAME
INDOOR POWER BOARD
INDOOR CONTROLLER BOARD
FUSE (T6.3AL250V)
CONNECTOR (LOSSNAY)
CONNECTOR (REMOTE SWITCH)
CONNECTOR (HA TERMINAL-A)
CONNECTOR (CENTRALLY CONTROLL)
POWER SUPPLY (I. B)
POWER SUPPLY (R. B)
TRANSMISSION(INDOOR-OUTDOOR)
RELAY (DEW PREVENTION HEATER)
RELAY(FAN MOTOR)
RELAY(FAN MOTOR)
RELAY(FAN MOTOR)
SWITCH (MODEL SELECTION) See Table 1.
SWITCH (CAPACITY CODE) See Table 2.
SYMBOL
MF1, MF2
C1, C2
H2
TB2
NAME
FAN MOTOR
CAPACITOR(FAN MOTOR)
DEW PREVENTION HEATER
TERMINAL BLOCK(INDOOR UNIT
POWER (OPTION))
TB4
TERMINAL BLOCK(INDOOR/OUTDOOR
TB5,TB6
CONNECTING LINE)
TERMINAL BLOCK(REMOTE CONTROLLER
TRANSMISSION LINE)
ROOM TEMP.THERMISTOR
(0°C/15k, 25°C/5.4k DETECT)
TH1
TH2
PIPE TEMP.THERMISTOR/LIQUID
(0°C/15k, 25°C/5.4k DETECT)
TH5
COND./ EVA.TEMP.THERMISTOR
(0°C/15k, 25°C/5.4k DETECT)
R. B
WIRED REMOTE CONTROLLER BOARD
SWITCH (EMERGENCY OPERATION)
SWE
For PCA-RP125HA
1
1
I.B
FAN 1 3 5 7
(WHT)
CN2S
(WHT)
1
2
DC13.1V
S1
S2
S3
FUSE
CN41
TH1
PIPE REMOCON
CN29
CN22
(BLK)
(BLU)
1 2
1 3
TH2
TH5
1 2
BLU
BLU
1 2
BLK
BLK
YLW
ORN
ORN
I.B
YLW
ORN
LED3 LED2 LED1 INTAKE LIQUID
CN20
CN21
(RED) (WHT)
1 2
1 2
WHT
WHT
SW1
Refer to tables 1
and 2 for service PCB.
ON
OFF
RED
BLU
GRN/YLW
CN51 CN32
ON
OFF
Table 1
SW1
Service board
1 2 3 4 5
+1 (Fig.1)
CN2L
X6 X5 X4
SW2
TO
OUTDOOR
UNIT
D.HEATER 1 3 ROWER 1 3 ROWER 1 3
1 2
1 3
CNC
CNDK
CND
ROWER INDOOR/OUTDOOR
COMMUNICATION
(RED)
(RED)
(ORN)
CN2D(WHT) CN3C(BLU)
X6 X5 X4
SWE
Please set the voltage using the
remote controller.
For the setting method, please refer to
the indoor unit Installation Manual.
TB4
YLW
ORN
ORN
BRN
BLK
WHT
H2
1
2
3
YLW
ORN
BRN
C2
GRY
(RED)
YLW
YLW
ORN
C1
RED
P.B CNDK
RED
WHT
6 5 4 3 2 1
BLK
BLU
YLW
WHT
6 5 4 3 2 1
BLK
BLU
YLW
WHT
ORN
RED
BLK
BLU
YLW
WHT
MF2
ORN
RED
BLK
BLU
YLW
WHT
MF1
1 3
BRN
TB2
L
N
POWER
SUPPLY
~(1PHASE)
230V 50Hz
TB4
S1
S2
S3
1 3
POWER INDOOR/OUTDOOR
CND COMMUNICATION
(ORN)
CN3C
(BLU)
TB5
2
TRANSMISSION WIRES DC12V
1
R.B
1
TB6
2
Table 2
MODELS
PCA-RP71HA
SW2
MODELS
Service board
Service board
1 2 3 4 5
1 2 3 4 5
ON PCA-RP125HA
ON
OFF
OFF
The black square (■) indicates a switch position.
Notes:
1. SymboIs used in wiring diagram above are,
: Connector,
: Terminal (block).
2. Indoor and outdoor connecting wires have poIarities, make sure to match terminal numbers (S1, S2, S3) for correct wirings.
3. Since the outdoor side electric wiring may change, be sure to check the outdoor unit electric wiring diagram for servicing.
4. This diagram shows the wiring of indoor and outdoor connecting wires (specification of 230V), adopting superimposed system for
power and signal.
+1: When supplying power separately to indoor and outdoor units, refer to Fig 1.
+2: For power supply system of this unit, refer to the caution label located near this diagram.
51
TO
OUTDOOR
UNIT
PSA-RP71GA
[LEGEND]
SYMBOL
P.B
I.B
FUSE
CN2L
CN32
CN41
CN51
LED1
LED2
LED3
PSA-RP100GA
PSA-RP125GA
NAME
SYMBOL
I.B SW1
INDOOR POWER BOARD
SW2
INDOOR CONTROLLER BOARD
FUSE (T6.3AL250V)
SWE
CONNECTOR (LOSSNAY)
X2
CONNECTOR (REMOTE SWITCH)
X4
X5
CONNECTOR (HA TERMINAL-A)
X6
CONNECTOR (CENTRALLY CONTROL)
R.B
POWER SUPPLY (I.B)
POWER SUPPLY (R.B)
TB6
TRANSMISSION (INDOOR-OUTDOOR)
HEATER
FS1,2
H
26H
88H
PSA-RP140GA
NAME
SWITCH (MODEL SELECTION) See Table 1.
SWITCH (CAPACITY CODE) See Table 2.
SWITCH (EMERGENCY OPERATION)
RELAY (LOUVER)
RELAY (FAN MOTOR)
RELAY (FAN MOTOR)
RELAY (FAN MOTOR)
WIRED REMOTE CONTROLLER BOARD
SYMBOL
C
MF
ML
NAME
CAPACITOR (FAN MOTOR)
FAN MOTOR
LOUVER MOTOR
TB2
TERMINAL BLOCK (HEATER) PSH-P·GAH
models only or option for PSA-RP·GA models.
TB4
TERMINAL BLOCK
(INDOOR/OUTDOOR CONNECTING LINE)
TH1
TERMINAL BLOCK (REMOTE CONTROLLER
TRANSMISSION LINE)
TH2
THERMAL FUSE (110°C16A)
HEATER
HEATER THERMAL SWITCH
HEATER CONTACTOR
ROOM TEMP.THERMISTOR
(0°C/15k, 25°C/5.4k DETECT)
PIPE TEMP.THERMISTOR/LIQUID
(0°C/15k, 25°C/5.4k DETECT)
TH5
COND./EVA.TEMP.THERMISTOR
(0°C/15k, 25°C/5.4k DETECT)
INDOOR UNIT
TB4
YLW
S1
P.B
CNSK
(RED)
CN2S
(WHT)
2
1
3
2
1
DC13.1V
S2
S3
Please set the voltage using the
remote controller.
For the setting method, please refer to
the indoor unit Installation Manual.
TO
OUTDOOR
UNIT
1 (Fig.1)
ORN
MF
ORN
RED
BLU
GRY/YLW
ML
C
X6 X5 X4
2
1
2
1
2
1
X2
X6 X5 X4
LED3 LED2 LED1
SW2
SWE
ON
SW1
OFF
CN24
TH2
Refer to tables 1
and 2 for service PCB.
R.B
2
1
I.B
YLW
YLW
1
LIQUID WIRELESS
CN21
CN90
(WHT)
(WHT)
INTAKE
CN20 REMOCON 2
(RED)
CN22
(BLU) 1
PIPE
CN29
(BLK)
CN2L
CN41 CN32
2
TB6
TH5
HEATER
CN24
(YLW)
88H 6YLW
FS2
6
5
RED 26H
RED
SW2
Service board
1
2 3 4 5
PSA-RP.GA
ON
PSH-P.GAH
OFF
MODELS
Table 2
SW2
Service board
PSA-RP71GA 1 2 3 4 5 ON
PSH-P71GAH
OFF
MODELS
1 2 3 4 5
PSA-RP125GA
PSH-P125GAH
1 2 3 4 5
PSA-RP140GA
PSH-P140GAH
1 2 3 4 5
FS1
RED
WHT
H
Table 1
PSA-RP100GA
PSH-P100GAH
BLU
1
TH1
PSH -P.GAH
models only
1 3
INDOOR/OUTDOOR
COMMUNICATION
CN3C
(BLU)
1
2
RED
BLU
L
N
TB4
S1
S2
S3
I.B
BRN
ORN
CN51
X2
1 2
POWER
CN2D
(WHT)
YLW
ORN
POWER 1 3
CND
(ORN)
BRN
ORN
POWER 1 3
CNDK
(RED)
BLK
WHT
RED
WHT
LOUVER 1 3
CNL
(YLW)
YLW
ORN
YLW
YLW
FAN 1 3 5 7
(WHT)
I.B
FUSE
BLK
BLU
YLW
WHT
RED
TB2
1 3
1 3
POWER SUPPLY
~(1PHASE)
230V 50Hz
TO
OUTDOOR
UNIT
POWER INDOOR/OUTDOOR
CND COMMUNICATION
(ORN)
CN3C
(BLU)
BLU
TRANSMISSION
WIRES DC12V
RED 5
88H
TB2
3 RED L
BLU N
GRN/YLW
POWER SUPPLY
~(1 PHASE)
230V 50Hz
Notes:
1. SymboIs used in wiring diagram above are,
: Connector, : Terminal (block).
2. Indoor and outdoor connecting wires have poIarities, make sure to match terminal
numbers (S1, S2, S3) for correct wirings.
3. Since the outdoor side electric wiring may change, be sure to check the outdoor unit
electric wiring diagram for servicing.
4. This diagram shows the wiring of indoor and outdoor connecting wires (specification of 230V),
adopting superimposed system for power and signal.
+1: When supplying power separately to indoor and outdoor units, refer to Fig 1.
+2: For power supply system of this unit, refer to the caution label located near this diagram.
ON
OFF
ON
OFF
ON
OFF
The black square (■) indicates a switch position.
52
4-2. OUTDOOR UNIT
PUHZ-RP35VHA4 PUHZ-RP50VHA4
SYMBOL
TB1
MC
MF1
21S4
63H
TH3, TH33
TH4
TH6
TH7
TH8
TH32
LEV-A, LEV-B
ACL
CY1,CY2
P.B.
TABR/S
TABU/V/W
NAME
Terminal Block<Power Supply, Indoor/Outdoor>
Motor for Compressor
Fan Motor
Solenoid Valve (Four-Way Valve)
High Pressure Switch
Thermistor<Outdoor Pipe>
Thermistor<Discharge>
Thermistor<Outdoor 2-Phase Pipe>
Thermistor<Outdoor>
Thermistor<Heat Sink>
Thermistor<Shell>
Electronic Expansion Valve
Reactor
Reactor
Power Circuit Board
Connection Terminal<L/N-Phase>
Connection Terminal<U/V/W-Phase>
SYMBOL
IPM
PFC
CB1~CB3
N.F.
LI/LO
NI/NO
EI,E2,E3
52C
C.B.
SW1
NAME
Power Module
Converter
Main Smoothing Capacitor
Noise Filter Circuit Board
Connection Terminal<L-Phase>
Connection Terminal<N-Phase>
Connection Terminal<Ground>
52C Relay
Controller Circuit Board
Switch<Forced Defrost, Defect History
Record Reset, Refrigerant Address>
Switch<Test Operation>
Switch<Function Switch>
Switch<Model Select>
Switch<Function Setup>
Switch<Function Setup>
Switch
SW4
SW5
SW6
SW7
SW8
SW9
SYMBOL
LED1,LED2
NAME
LED
<Operation Inspection Indicators>
Fuse<T6.3AL250V>
Switch<Pump Down>
Connector<Emergency Operation>
Connector<Connection for Option>
Connector<Connection for Option>
Connector<A-Control Service Inspection Kit>
Connector
<Connected to Optional M-NET Adapter Board>
Connector
<Connected to Optional M-NET Adapter Board>
Connector
< Connected for Option (Contact Input)>
Relay
F1~4
SWP
CN31
CN51
SS
CNM
CNMNT
CNVMNT
CNDM
X51,X52
When M-NET adapter is connected
LEV-B
M
M
5
C. B.
t°
1
2 1
TH7/6 TH3 TH4
(RED) (WHT) (WHT)
LEV-A
(WHT)
6
1
6
1
CN2
(WHT)
3
1
TRANS
3
1
LEV-B CNVMNT CNMNT
(RED) (WHT) (WHT)
1
3
7
14
CNM
(WHT)
1 2
2
F1
3
1
X52
2
21S4 3
(GRN)
F4
4
M-NET ADAPTER
2
1
CND
(WHT)
3 1
3
A B S
1
TB7
5
M-NET
1
X51
5
F3
CNAC
(WHT)
1
LED4
3
1 2
2
SW12
LED3
CN31
CN52C
(RED)
CN4
(WHT)
CNDC 1
(PNK)
F2
5
CNDM
(WHT)
12
CN51
(WHT)
TH33 TH32
(YLW) (BLK)
4
SW5
1
SW6
12
SW1
3
*1
SW4 SWP SW8
1
1
3
LED2
*1
63H
(YLW)
CNS
(WHT)
5
t°
LED1
CNF1
7 (WHT)
1
t° t°
LED2
MF1
MS
3~
t°
SW1
1
SW9 SW7
t°
5
3
SW11
CN5
(WHT)
TH33 TH32 TH7 TH6 TH3 TH4
LEV-A
LED5 CN2M
(WHT)
LED1
63H
1
3
1 SS
(WHT)
21S4
RED
RED
RED
WHT
WHT
WHT
N. F.
ACL
MC
MS
3~
NO
PFC
2
CN4 1
(WHT) 2
2
2
CN52C
(BLK)
CN5 1
(RED) 2
2
1
52C
U
RED
BLK
P. B.
WHT
W V
LO
IPM
TABV
TABW
RED
WHT
TABS
E3
1
TH8
CN3 1
(WHT) 2
3
t°
CNAC2
(RED)
TABR
BLK
5
1
CN5
(RED)
TABU
CN2
(WHT)
CB1
CB2
CB3
1
7
2
2
E2
BLK
1
CNAC1
(WHT)
3
*1MODEL SELECT
L
N
CY1
CY2
S1
S2
EI
NI
LI
BRN
YLW
1 2 3 4 5 6
*2. SW5 -1 to 5 : Function Switch
The black square (■) indicates a switch position.
U
BLK
1 2 3 4 5 6 7 8
ON
OFF
ORN
ON
OFF
U
1 2 3 4 5 6
GRN/YLW
50V
1 2 3 4 5 6 7 8
SW5-6 *2
ON
OFF
BLU
35V
SW6
ON
OFF
RED
MODEL
S3 TB1
M-NET ADAPTER
INDOOR
UNIT
POWER SUPPLY
~/N 230V 50Hz
53
SYMBOL
TB7
CN5
CND
CN2M
SW1
SW11
NAME
Terminal Block<M-net connection>
Connector<Transmission>
Connector<Power Supply>
Connector<M-NET communication>
Switch<Status of communication>
Switch<Address setting : 1s digit>
SYMBOL
SW12
LED1
LED2
LED3
LED4
LED5
NAME
Switch<Address setting : 10s digit>
LED<Power Supply : DC5V>
LED<Connection to Outdoor Unit>
LED<Transmission : Sending>
LED<Transmission : Recelving>
LED<Power Supply : DC12V>
PUHZ-RP60VHA4 PUHZ-RP71VHA4
SYMBOL
TB1
MC
MF1
21S4
63H
TH3, TH33
TH4
TH6
TH7
TH8
TH32
LEV-A, LEV-B
ACL
CY1,CY2
P.B.
TABR/S
TABU/V/W
IPM
NAME
Terminal Block<Power Supply, Indoor/Outdoor>
Motor for Compressor
Fan Motor
Solenoid Valve (Four-Way Valve)
High Pressure Switch
Thermistor<Outdoor Pipe>
Thermistor<Discharge>
Thermistor<Outdoor 2-Phase Pipe>
Thermistor<Outdoor>
Thermistor<Heat Sink>
Thermistor<Shell>
Electronic Expansion Valve
Reactor
Reactor
Power Circuit Board
Connection Terminal<L/N-Phase>
Connection Terminal<U/V/W-Phase>
Power Module
SYMBOL
PFC
CB1~CB3
N.F.
LI/LO
NI/NO
EI,E2,E3
52C
C.B.
SW1
NAME
Converter
Main Smoothing Capacitor
Noise Filter Circuit Board
Connection Terminal<L-Phase>
Connection Terminal<N-Phase>
Connection Terminal<Ground>
52C Relay
Controller Circuit Board
Switch<Forced Defrost, Defect History
Record Reset, Refrigerant Address>
Switch<Test Operation>
Switch<Function Switch>
Switch<Model Select>
Switch<Function Setup>
Switch<Function Setup>
Switch
LED
<Operation Inspection Indicators>
SW4
SW5
SW6
SW7
SW8
SW9
LED1,LED2
SYMBOL
F1~4
SWP
CN31
CN51
SS
CNM
CNMNT
NAME
Fuse<T6.3AL250V>
Switch<Pump Down>
Connector<Emergency Operation>
Connector<Connection for Option>
Connector<Connection for Option>
Connector<A-Control Service Inspection Kit>
Connector
<Connected to Optional M-NET Adapter Board>
Connector
<Connected to Optional M-NET Adapter Board>
Connector
< Connected for Option (Contact Input)>
Relay
CNVMNT
CNDM
X51,X52
When M-NET adapter is connected
TH33 TH32 TH7 TH6 TH3 TH4
LEV-A
LEV-B
M
M
5
t°
1
2 1
LEV-A
(WHT)
6
1
6
1
1
3
1
TRANS
7
14
F1
3
1
2
21S4 3
(GRN)
F4
4
3
A B S
1
TB7
5
M-NET
1
X51
X52
2
CND
(WHT)
3 1
3
1 2
5
F3
CNAC
(WHT)
1
M-NET ADAPTER
2
1
CN31
1 2
2
F2
5
CN52C
(RED)
CN4
(WHT)
CNDC 1
(PNK)
3
1
CNM
(WHT)
63H
(YLW)
CN2
(WHT)
3
3
LEV-B CNVMNT CNMNT
(RED) (WHT) (WHT)
SW6
12
SW1
4
TH7/6 TH3 TH4
(RED) (WHT) (WHT)
CNDM
(WHT)
1
LED4
CN51
(WHT)
12
SW4 SWP SW8
3
LED1
1
TH33 TH32
(YLW) (BLK)
SW12
LED3
*1
SW5
*1
1
CNS
(WHT)
LED2
t°
LED5 CN2M
(WHT)
LED1
t° t°
LED2
MF1
MS
3~
t°
SW11
SW1
1
5
SW9 SW7
t°
CNF1
7 (WHT)
5
3
C. B.
1
CN5
(WHT)
63H
1
3
1 SS
(WHT)
21S4
RED
RED
WHT
WHT
RED
WHT
N. F.
ACL
MS
3~
NO
PFC
2
CN4 1
(WHT) 2
2
2
CN52C
(BLK)
CN5 1
(RED) 2
2
1
52C
U
RED
BLK
P. B.
WHT
W V
LO
MC
IPM
TABV
TABW
RED
WHT
TABS
E3
3
TH8
CN3 1
(WHT) 2
1
t°
CNAC2
(RED)
TABR
BLK
5
1
CN5
(RED)
TABU
CN2
(WHT)
CB1
CB2
CB3
1
7
2
2
E2
BLK
*1MODEL SELECT
CNAC1
(WHT)
3
The black square (■) indicates a switch position.
L
N
NI
CY1
CY2
S1
S2
S3 TB1
INDOOR
UNIT
POWER SUPPLY
~/N 230V 50Hz
EI
BLK
*2. SW5 -1 to 5 : Function Switch
U
LI
YLW
1 2 3 4 5 6
U
BRN
1 2 3 4 5 6
ORN
1 2 3 4 5 6 7 8
ON
OFF
1
GRN/YLW
71V
ON
OFF
1 2 3 4 5 6 7 8
SW5-6 *2
ON
OFF
BLU
60V
SW6
ON
OFF
RED
MODEL
M-NET ADAPTER
SYMBOL
TB7
CN5
CND
CN2M
SW1
SW11
NAME
Terminal Block<M-net connection>
Connector<Transmission>
Connector<Power Supply>
Connector<M-NET communication>
Switch<Status of communication>
Switch<Address setting : 1s digit>
54
SYMBOL
SW12
LED1
LED2
LED3
LED4
LED5
NAME
Switch<Address setting : 10s digit>
LED<Power Supply : DC5V>
LED<Connection to Outdoor Unit>
LED<Transmission : Sending>
LED<Transmission : Receiving>
LED<Power Supply : DC12V>
PUHZ-RP100VKA PUHZ-RP125VKA PUHZ-RP140VKA
SYMBOL
LI
NI
P2
N2
DCL1,DCL2
IGBT
EI,E2,E3,E4
C.B.
SW1
NAME
Connection Terminal<L-Phase>
Connection Terminal<N-Phase>
Connection Terminal
Connection Terminal
Connection Terminal<Reactor>
Power Module
Connection Terminal<Ground>
Controller Circuit Board
Switch<Forced Defrost, Defect History Record
Reset, Refrigerant Address>
Switch<Test Operation>
Switch<Function Switch>
Switch<Model Select>
Switch<Function Setup>
Switch<Function Setup>
Switch
SW4
SW5
SW6
SW7
SW8
SW9
SYMBOL
SWP
CN31
CN51
SS
CNM
CNMNT
CNVMNT
CNDM
LED1, LED2
F1~F4
X51,X52
RP140 only
LEV-C
M
M
TH33 TH32 TH7 TH6 TH3 TH4
C. B.
t°
t°
t° t°
3
12
t°
t°
12
2 1
CNF2
(WHT)
1
1
TRANS
2
CNDC 1
(PNK)
CN2
(WHT)
LEV-B
(RED)
1
1
1
5
CNVMNT CNMNT
(WHT) (WHT)
LEV-C 6
(BLU)
1
14
CNM
(WHT)
CN52C
(RED)
CN4
(WHT)
7
3
1
1 2
3
F1
3
1
2
21S4 3
(GRN)
F4
4
X51
F3
CNAC
(WHT)
1
1
3
SW12
LED4
2
1
M-NET ADAPTER
CN2M
(WHT)
CND
(WHT)
3 1
CN31
3
2
LED3
*1
7
F2
3
3
63H
(YLW)
3
CNS
(WHT)
*1
6
X52
1
LEV-A
(WHT)
1
CNDM
(WHT)
TH33 TH32 TH7/6 TH3 TH4
(YLW) (BLK) (RED) (WHT) (WHT)
7
6
3
3
1
CN51
(WHT)
1
SW5
4
SW4 SWP SW8
1
SW11
CN5
(WHT) SW1
1
LED2
5
5
1
LED1
1
CNF1
(WHT)
LED2
5
A B S
TB7
M-NET
1
1 SS
(WHT)
21S4
2
P. B.
1
2
CN4
(WHT)
1
CN2
(WHT)
CN52C
3 (RED)
1
7
52C
52C
BLK
2
WHT
E3
CNDC
(PNK)
N2
3
1
CB
CNAC2
(RED)
1
P2
RED
IGBT
3
BLK
E2
1
3
CNAC1
(WHT)
E4
W V U
DCL2
DCL
W V U
MS
3~
DCL1
EI
*1. MODEL SELECT
ON
100V OFF
ON
125V OFF
ON
140V OFF
L
SW6
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
LI
BLU
N
S1
S2
BRN
GRN/YLW
YLW
ORN
M-NET ADAPTER
MC
MODEL
NI U
U
BLK
BLK
RED
MF2
MS
3~
5
5
3
5
7
BLK
WHT
RED
MF1
MS
3~
When M-NET adapter is connected
M
SW6
LEV-B
SW9 SW7
LEV-A
SW1
63H
NAME
Switch<Pump Down>
Connector<Emergency Operation>
Connector<Connection for Option>
Connector<Connection for Option>
Connector<A-Control Service Inspection Kit>
Connector
<Connected to Optional M-NET Adapter Board>
Connector
<Connected to Optional M-NET Adapter Board>
Connector
< Connected for Option (Contact Input)>
LED<Operation Inspection Indicators>
Fuse< T6.3AL250V>
Relay
LED1
NAME
Terminal Block<Power Supply, Indoor/Outdoor >
Motor for Compressor
Fan Motor
Solenoid Valve (Four-Way Valve)
High Pressure Switch
Thermistor<Outdoor Pipe>
Thermistor<Discharge>
Thermistor<Outdoor 2-Phase Pipe>
Thermistor<Outdoor>
Thermistor<Shell>
Electronic Expansion Valve
Reactor
Main Smoothing Capacitor
Capacitor
Power Circuit Board
Connection Terminal<U/V/W-Phase>
LED5
SYMBOL
TB1
MC
MF1, MF2
21S4
63H
TH3, TH33
TH4
TH6
TH7
TH32
LEV-A, LEV-B, LEV-C
DCL
CB
CY1,CY2
P.B.
U/V/W
S3 TB1
SW5-6 *2
ON
OFF
ON
OFF
ON
OFF
INDOOR
UNIT
1 2 3 4 5 6
1 2 3 4 5 6
POWER SUPPLY
~/N 230V 50Hz
1 2 3 4 5 6
*2. SW5 -1 to 5 : Function Switch
The black square (■) indicates a switch position.
55
CY1
CY2
SYMBOL
TB7
CN5
CND
CN2M
SW1
SW11
SW12
LED1
LED2
LED3
LED4
LED5
NAME
Terminal Block<M-net connection>
Connector<Transmission>
Connector<Power Supply>
Connector<M-NET communication>
Switch<Status of communication>
Switch<Address setting : 1s digit>
Switch<Address setting : 10s digit>
LED<Power Supply : DC5V>
LED<Connection to Outdoor Unit>
LED<Transmission : Sending>
LED<Transmission : Recelving>
LED<Power Supply : DC12V>
PUHZ-RP100YKA PUHZ-RP125YKA PUHZ-RP140YKA
SYMBOL
TB1
TB2
MC
MF1, MF2
21S4
63H
TH3, TH33
TH4
TH6
TH7
TH32
LEV-A,LEV-B,LEV-C
ACL1~ACL4
CB1, CB2
CK
RS
P.B.
TB-U/V/W
TB-L1/L2/L3
NAME
Terminal Block<Power Supply >
Terminal Block<Indoor/Outdoor >
Motor for Compressor
Fan Motor
Solenoid Valve (Four-Way Valve)
High Pressure Switch
Thermistor<Outdoor Pipe>
Thermistor<Discharge>
Thermistor<Outdoor 2-Phase Pipe>
Thermistor<Outdoor>
Thermistor<Shell>
Electronic Expansion Valve
Reactor
Main Smoothing Capacitor
Capacitor
Rush Current Protect Resistor
Power Circuit Board
Connection Terminal<U/V/W-Phase>
Connection Terminal<L1/L2/L3-Power Supply>
SYMBOL
TB-P2
TB-C1
TB-N1
X52A
N.F.
LI1/LI2/LI3/NI
LO1/LO2/LO3/NO
GD1, GD3
CONV.B.
L1-A1/IN
L1-A2/OU
L2-A2/OU
L3-A2/OU
N-IN
CK-OU
C.B.
SW1
NAME
Connection Terminal
Connection Terminal
Connection Terminal
52C Relay
Noise Filter Circuit Board
Connection Terminal<L1/L2/L3/N-Power Supply>
Connection Terminal<L1/L2/L3/N-Power Supply>
Connection Terminal<Ground>
Converter Circuit Board
Connection Terminal<L1-Power Supply>
Connection Terminal<L1-Power Supply>
Connection Terminal<L2-Power Supply>
Connection Terminal<L3-Power Supply>
Connection Terminal
Connection Terminal
Controller Circuit Board
Switch<Forced Defrost, Defect History Record
Reset, Refrigerant Adress>
Switch<Test Operation>
SW4
SYMBOL
SW5
SW6
SW7
SW8
SW9
SWP
CN31
LED1,LED2
F1~F4
CNM
CNMNT
CNVMNT
CNDM
CN3S
CN51
X51,X52
NAME
Switch<Function Switch>
Switch<Model Select>
Switch<Function Setup>
Switch<Function Setup>
Switch
Switch<Pump Down>
Connector<Emergency Operation>
LED<Operatiion Inspection Indicators>
FUSE<T6.3AL250V>
Connector<A-Control Service Inspection Kit>
Connector
<Connect to Optional M-NET Adapter Board>
Connector
<Connect to Optional M-NET Adapter Board>
Connector
< Connection for Option(Contact Input)>
Connector< Connection for Option>
Connector< Connection for Option>
Relay
RP140 only
LEV-C
5
CNF2
(WHT)
1
1
3
63H
(YLW)
TRANS
1
LEV-A
(WHT)
6
1
5
6
LEV-B
(RED)
1 3 1
5
CNVMNT CNMNT
(WHT) (WHT)
1
LEV-C 6
(BLU)
1
14
CNM
(WHT)
CN4
(WHT)
1 2
CN2
(WHT) 7
1
CNDC
(PNK)
2
3
1
3
TB7
M-NET
1
1 SS
(WHT)
7
7
V MS
3~
RED
+
+
RED
CB1
+
CB2
3
3
1
CK
CONV.B.
L1-IN
L1-A1
RED
+
TB-N1
TB-C1
WHT
TB-P2
2
2 1
BLU
CNAC2
3 (RED)
RED
CNCT
(RED) 1
3
RED
N.F.
CNAC1
(WHT) 1
ACL1
TB1
POWER SUPPLY
3N~
400V 50Hz
L2
L3
N
RED
LI1
WHT
LI2 U
BLK
BLU
LI3
NI
LO1
RED
U
LO2
WHT
U
LO3
BLK
U
NO
BLU
GRN/YLW
CNDC
(PNK)
1
3
2
3
ACL3
*1. MODEL SELECT
MODEL
ON
100Y OFF
U -1 CNL
(BLU)
WHT
BLK
BLK
GD3
BRN
GD1
ACL2
+
+
U
L1-A2
WHT
TB-L1
BLK CK-OU
BLK
TB-L2
L2-A2
--
TB-L3
RED
RED
TB-U
+
X52A
WHT
U
--
2 CN5
1 (RED)
W MC
BLK
TB-V
RS
ORN
TB-W
+
L1-OU RED
CN2
(WHT)
N-IN
YLW
1
2 CN4
1 (WHT)
RED
L1
ACL4
ON
125Y OFF
M-NET ADAPTER
TB7
CN5
CND
CN2M
SW1
SW11
CND
(WHT)
3 1
A B S
5
L3-A2 WHT
3
BRN
S3
3
1
L2-OU WHT
2
S2
M-NET ADAPTER
2
1
CN7
(WHT)
BLK
BLU
2
INDOOR
UNIT
3
SW12
LED3
LED4
21S4
1 3
CN7
(WHT)
S1
1 21S4
(GRN)
3 4
P.B.
TB2
X51
X52
3
SW11
SW1
LED2
BLK
1
F4
BLK
F1
CNS
(WHT)
3
F3
CNAC
(WHT)
1 2
1
CN31
CN51
(WHT)
7
F2
SW6
1 2 21
TH3 TH4
(WHT) (WHT)
SW1
1
4
TH7/6
(RED)
SW5
1 3 1 2
TH33 TH32
(YLW) (BLK)
5
*1
LED5 CN2M
(WHT)
LED1
5
t°
*1
3
2
5
CNDM CN3S
(WHT) (WHT)
7
MS
3~
When M-NET adapter is connected
3
SW4 SWP SW8
1
MF2
t°
M
LED1
MS
3~
t° t°
LED2
1
MF1
t°
M
SW7
t°
CNF1
7 (WHT)
LEV-B
M
L3-OU BLK
C.B.
LEV-A
SW9
TH33 TH32 TH7 TH6 TH3 TH4
CN5
(WHT)
63H
Terminal Block<M-NET connection >
Connector<Transmission>
Connector<Power Supply>
Connector<M-NET communication>
Switch<Status of communication>
Switch<Address setting: 1s digit>
SW12
LED1
LED2
LED3
LED4
LED5
Switch<Address setting. 10s digit >
LED<Power Supply: DC5V>
LED<Connection to Outdoor Unit>
LED<Transmission: Sending>
LED<Transmission: Receiving>
LED<Power Supply: DC12V>
56
ON
140Y OFF
SW6
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
SW5-6 *2
ON
OFF
ON
OFF
ON
OFF
1 2 3 4 5 6
1 2 3 4 5 6
1 2 3 4 5 6
*2. SW5 -1 to 5 : Function Switch
The black square (■) indicates a switch position.
PUHZ-RP200YKA PUHZ-RP250YKA
SYMBOL
TB1
TB2
MC
MF1,MF2
21S4
63H,63H1,63H2
TH3
TH4
TH6
TH7
TH32
LEV-A,LEV-B
ACL4
DCL
CB1,CB2
RS
FUSE1, FUSE2
CY1,CY2
NAME
Terminal Block<Power Supply>
Terminal Block<Indoor/Outdoor>
Motor for Compressor
Fan Motor
Solenoid Valve (Four-Way Valve)
High Pressure Switch
Thermistor<Outdoor Pipe>
Thermistor<Discharge>
Thermistor<Outdoor 2-Phase Pipe>
Thermistor<Outdoor>
Thermistor<Shell>
Electronic Expansion Valve
Reactor
Reactor
Main Smoothing Capacitor
Rush Current Protect Resistor
Fuse<T15AL250V>
Capacitor
SYMBOL
P.B.
SC-U/V/W
TB-L1/L2/L3
TB-P1
TB-P2
TB-C1
TB-N1
X52A
N.F.
LI1/ LI2/LI3/NI
LO1/ LO2/LO3
GD1,GD2
C.B.
SW1
NAME
Power Circuit Board
Connection Terminal<U/V/W-Phase>
Connection Terminal<L1/L2/L3-Power supply>
Connection Terminal
Connection Terminal
Connection Terminal
Connection Terminal
52C Relay
Noise Filter Circuit Board
Connection Terminal<L1/L2/L3/NI-Power supply>
Connection Terminal<L1/L2/L3-Power supply>
Connection Terminal<Ground>
Controller Circuit Board
Switch<Forced Defrost, Defect History Record
Reset, Refrigerant Address>
Switch<Test Operation>
Switch<Function Switch>
Switch<Model Select>
SW4
SW5
SW6
SYMBOL
SW7
SW8
SW9
SWP
CN31
LED1,LED2
F3,F4
SS
CNM
CNMNT
CNVMNT
CNDM
CN3S
CN51
X51,X52
NAME
Switch<Function Setup>
Switch<Function Setup>
Switch
Switch<Pump Down>
Connector<Emergency Operation>
LED<Operation Inspection Indicators>
Fuse< T6.3AL250V>
Connector<Connection for Option>
Connector<A-Control Service Inspection Kit>
Connector
<Connected to Optional M-NET Adapter Board>
Connector
<Connected to Optional M-NET Adapter Board>
Connector
< Connected for Option (Contact Input)>
Connector<Connection for Option>
Connector<Connection for Option>
Relay
*3.
*3.
For RP200 For RP250
63H2
5
5
1 3 1
5
CNVMNT CNMNT
(WHT)
(WHT)
CN2
(WHT)
3
1
TRANS
2
1
LED2
1 3
63H
(YLW)
1
14
CNM
(WHT)
CNS
(WHT)
1
FUSE1
1 21S4
(GRN)
4
FUSE2 RED
WHT
3
X51
X52
3
F4
3
3
1
SW12
LED3
LED4
M-NET ADAPTER
2
1
CN51
(WHT)
7
F3
CNAC
(WHT)
1
2
LED2
CN31
2
CNDC
(PNK)
1
*1
CN4
(WHT)
1 2
7
SW11
SW1
LED1
6
SW7
LEV-B
(RED)
SW6
1
SW1
6
LEV-A
(WHT)
SW5
1
4 12 21
1 2 1
TH32 TH7/6 TH3 TH4
(BLK) (RED) (WHT) (WHT)
CNF2
7 (WHT)
MS
3~
CN5
(WHT)
t°
*1
CNF1
7 (WHT)
1
t°
5
CNDM CN3S
(WHT) (WHT)
MF2
t°
When M-NET adapter is connected
3
SW4 SWP SW8
1
MS
3~
t°
M
LED1
MF1
t°
LEV-B
M
SW9
C. B.
LEV-A
63H1
LED5 CN2M
(WHT)
63H
TH32 TH7 TH6 TH3 TH4
CND
(WHT)
3 1
1
3
3
1
3
A B S
TB7
1
M-NET
5
SS
(WHT)
21S4
P. B.
7
RED
WHT
7
CN2
(WHT)
1
2
2 CN4
1 (WHT)
2 CN5
1 (RED)
CY2
BLK
BLK
SC-V
WHT
SC-U
RED
TB-L3
BLK
TB-L2
WHT
TB-L1
RED
MC
W
V MS
3~
U
X52A
RS
CY1
2
SC-W
BLK
S3
TB-P2
TB-C1
TB-N1
BLK
RED
DCL
BRN
S2
INDOOR
UNIT
RED TB-P1
ORN
S1
WHT
YLW
TB2
CB1
CB2
2
N. F.
CNAC1
(WHT) 1
CNCT
(RED) 1
3
2 1
CNAC2
3 (RED)
TB1
RED
LI 1
WHT
LI 2
L3
BLK
LI 3
U
N
BLU
NI
U
L1
POWER
SUPPLY
3N~
400V 50Hz
L2
U
U
LO 1
RED
LO 2
WHT
LO3
BLK
*1 MODEL SELECT
MODEL
GRN/YLW
ON
200Y OFF
U
U
SYMBOL
TB7
CN5
CND
CN2M
SW1
SW11
SW12
LED1
LED2
LED3
LED4
LED5
2
3
3
1 CNL
(BLU)
WHT
CNDC 1
(PNK)
WHT
GD2
BLK
M-NET ADAPTER
BLK
GD1
ACL4
ON
250Y OFF
SW6
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
SW5-6 *2
ON
OFF
ON
OFF
1 2 3 4 5 6
1 2 3 4 5 6
*2. SW5 -1 to 5 : Function Switch
The black square (■) indicates a switch position.
NAME
Terminal Block(M-NET connection)
Connector<Transmission>
Connector<Power Supply>
Connector<M-NET communication>
Switch<Status of communication>
Switch<Address setting:1s digit>
Switch<Address setting:10s digit>
LED<Power Supply:DC5V>
LED<Connection to Outdoor Unit>
LED<Transmission:Sending>
LED<Transmission:Receiving>
LED<Power Supply:DC12V>
57
5
REFRIGERANT SYSTEM DIAGRAM
5-1. INDOOR UNIT
PLA-RP·BA/BA2/BA3 PEAD-RP·JA(L)
PCA-RP·KA
PCA-RP·HA
PSA-RP·GA
Strainer(#50)
Heat exchanger
Refrigerant GAS pipe connection
(Flare)
Thermistor TH5
(Cond./Eva. temperature)
Refrigerant flow in cooling
Refrigerant flow in heating
Distributor
Thermistor TH2
with strainer(#50) Pipe temperature (Liquid)
Thermistor TH1
(Room temperature)
Refrigerant LIQUID pipe connection
(Flare)
Strainer(#50)
PKA-RP·HAL
PKA-RP·KAL
Strainer (#50)
Heat exchanger
Refrigerant GAS pipe connection
(Flare)
Thermistor TH2
Pipe temperature(Liquid)
Thermistor TH5
(Cond./ Eva.temperature)
Refrigerant flow in cooling
Refrigerant flow in heating
Refrigerant LIQUID pipe connection
(Flare)
Thermistor TH1
(Room temperature)
Distributor with strainer
(#50/#50: HAL)
(#50/#100: KAL)
58
Strainer (#50)
PEA-RP200, 250GA
Strainer
Heat exchanger
Refrigerant GAS pipe connection
Brazing
Condenser/evaporator
temperature thermistor
(TH5)
Refrigerant flow in cooling
Refrigerant flow in heating
Refrigerant LIQUID pipe connection
Brazing
Room temperature
thermistor(TH1)
Pie temperature
thermistor/Liquid
(TH2)
Strainer
PEA-RP400GA PEA-RP500GA
Strainer
Heat exchanger
Refrigerant GAS pipe connection
Brazing
Condenser/evaporator
temperature thermistor
(TH5-2)
Refrigerant flow in cooling
Refrigerant flow in heating
Refrigerant LIQUID pipe connection
Brazing
Pie temperature
thermistor/Liquid
(TH2-2)
Strainer
Strainer
Refrigerant GAS pipe connection
Brazing
Condenser/evaporator
temperature thermistor
(TH5-1)
Refrigerant LIQUID pipe connection
Brazing
Room temperature
thermistor(TH1-1)
Pie temperature
thermistor/Liquid
(TH2-1)
Strainer
Room temperature
thermistor(TH1-2)
59
unit: mm(inch)
5-2. OUTDOOR UNIT
PUHZ-RP35VHA4
PUHZ-RP50VHA4
Heat exchanger
Stop valve
(with service port)
Refrigerant GAS pipe
connection ø12.7 (1/2F)
Thermistor TH6
(Outdoor 2-phase pipe)
Charge plug
Solenoid valve
(Four-way valve)
Thermistor TH7
(Outdoor)
Strainer
#50
Thermistor TH3
(Outdoor pipe)
Muffler
Distributor
High pressure
switch 63H
Thermistor TH4
(Discharge)
Thermistor TH32
(Shell)
Linear
expansion valve B
Compressor
Power
receiver
Linear expansion valve A
Stop valve
Refrigerant LIQUID pipe
connection ø6.35 (1/4F)
Strainer
#100
Strainer
#100
Refrigerant flow in cooling
Refrigerant flow in heating
PUHZ-RP60VHA4
PUHZ-RP71VHA4
Heat exchanger
Stop valve
(with service port)
Refrigerant GAS pipe
connection :15.88(5/8)
Thermistor TH33
(Outdoor pipe)
4-way valve
Strainer
#50
Muffler
Charge plug
(Low pressure)
Charge plug
(Higt pressure)
Thermistor TH7
(Outdoor)
Thermistor TH6
(Outdoor 2-phase pipe)
Thermistor TH3
(Outdoor pipe)
High pressure
switch 63H
Distributor
Thermistor TH4
(Discharge)
Strainer
#100
Linear
expansion valve B
Stop valve
(with service port)
Refrigerant LIQUID pipe
connection :9.52(3/8)
Thermistor TH32
(Shell)
Power
receiver
Strainer
#100
Compressor
Linear expansion valve A
Strainer
#100
Strainer
#100
60
Thermistor TH33
(Outdoor pipe)
PUHZ-RP100VKA
PUHZ-RP100YKA
unit: mm(inch)
PUHZ-RP125VKA
PUHZ-RP125YKA
Heat exchanger
Ball valve
4-way valve
Strainer
#50
Refrigerant GAS pipe
connection ø15.88 (5/8)
Muffler
Charge plug
(Low pressure)
Thermistor TH7
(Outdoor)
Thermistor TH6
(Outdoor 2-phase pipe)
Charge plug
(Higt pressure)
Thermistor TH3
(Outdoor pipe)
Distributor
High pressure
switch 63H
Strainer
#100
Thermistor TH4
(Discharge)
Strainer
#100
Linear
expansion valve B
Stop valve
(with service port)
Refrigerant LIQUID pipe
connection ø9.52 (3/8)
Thermistor TH32
(Shell)
Power
receiver
Strainer
#100
Thermistor TH33
(Outdoor pipe)
Compressor
Linear expansion valve A
Strainer
#100
Strainer
#100
Refrigerant flow in cooling
Refrigerant flow in heating
PUHZ-RP140VKA
PUHZ-RP140YKA
Heat exchanger
Ball valve
Refrigerant GAS pipe
connection :15.88(5/8)
4-way valve
Strainer #50
Muffler
Charge plug
(Low pressure)
Charge plug
(Higt pressure)
Stop valve
(with service port)
Refrigerant LIQUID
pipe connection
:9.52(3/8)
Strainer
#100
Distributor
Thermistor TH4
(Discharge)
Strainer
#100
Linear
expansion
valve B
Thermistor TH3
(Outdoor pipe)
High pressure
switch 63H
Strainer
#100
Thermistor TH7
(Outdoor)
Thermistor TH6
(Outdoor 2-phase pipe)
Thermistor TH32
(Shell)
Power
receiver
Heat interchange
circuit
Strainer
#100
Thermistor
TH33
(Outdoor pipe)
Compressor
Linear expansion valve A
Strainer
#100
Linear
expansion
valve C
61
unit: mm(inch)
PUHZ-RP200YKA
Heat exchanger
Ball valve
Thermistor TH6
(Outdoor 2-phase pipe)
4-way valve
Strainer
#50
Refrigerant GAS pipe
connection :25.4(1)
Muffler
Charge plug
(Low pressure)
Charge plug
(Higt pressure)
Refrigerant LIQUID pipe
connection :9.52(3/8)
Distributor
Thermistor TH4
(Discharge)
Strainer
#100
Stop valve
(with service port)
Thermistor TH3
(Outdoor pipe)
High pressure
switch 63H
Strainer
#100
Linear
expansion valve B
Thermistor TH7
(Outdoor)
Thermistor TH32
(Shell)
Strainer
#100
Power
receiver
Compressor
Linear expansion valve A
Strainer
#100
Strainer
#100
PUHZ-RP250YKA
Refrigerant flow in cooling
Refrigerant flow in heating
Ball valve
Heat exchanger
High pressure
switch(63H2)
Refrigerant GAS pipe
:25.4 (1)
Thermistor (TH6)
4-way valve
Strainer
(#50)
Muffler
Service
port
(check)
Thermistor (TH32)
Strainer (Shell)
(#100)
Stop valve
(with service port)
Refrigerant LIQUID pipe
:12.7 (1/2)
Service
port
(check)
Power
receiver
Thermistor (TH3)
High pressure
switch (63H1)
Thermistor (TH4)
(Discharge)
Strainer
(#100)
Strainer
(#100)
Linear
expansion valve B
Thermistor (TH7)
Compressor
Linear expansion valve A
Strainer
(#100)
Strainer
(#100)
62
Distributor
6
PERFORMANCE CURVES
FOR THE COMBINATION OF OUTDOOR UNIT
Cooling capacity
1.4
Cooling capacity ratio
Indoor intake air wet-bulb temperature <W.B. :>
1.2
22
1.0
20
18
0.8
0.6
16
-5
0
5
10
15
20
25
30
35
40
46
Outdoor intake air dry-bulb temperature <D.B. >
Cooling input
22 20
18
16
Cooling input ratio
1.2
1.0
0.8
0.6
Indoor intake air wet-bulb temperature <W.B. :>
0.4
-5
0
5
10
15
20
25
30
35
40
Outdoor intake air dry-bulb temperature <D.B. >
Note : These diagrams show the case where the operation frequency of a compressor is fixed.
63
46
Heating capacity
Indoor intake air dry-bulb temperature <D.B. :>
Outdoor intake air wet-bulb temperature <W.B. :>
Heating input
Indoor intake air dry-bulb temperature <D.B. :>
Outdoor intake air wet-bulb temperature <W.B. :>
Note : These diagrams show the case where the operation frequency of a compressor is fixed.
64
7
CORRECTION FACTORS
7-1. PUHZ-RP·VHA4 PUHZ-RP·VKA PUHZ-RP100-140YKA
Cooling capacity correction factors
5m
10m
20m
Refrigerant piping length (one way)
30m
40m
50m
55m
PUHZ-RP35VHA4
1.00
0.992
0.976
0.962
0.949
0.936
PUHZ-RP50VHA4
1.00
0.985
0.957
0.931
0.908
PUHZ-RP60VHA4
1.00
0.992
0.976
0.962
PUHZ-RP71VHA4
1.00
0.988
0.966
1.00
0.985
1.00
1.00
Outdoor unit
PUHZ-RP100VKA
PUHZ-RP100YKA
PUHZ-RP125VKA
PUHZ-RP125YKA
PUHZ-RP140VKA
PUHZ-RP140YKA
60m
70m
80m
0.930
—
—
—
0.886
0.876
—
—
—
0.949
0.936
0.930
—
—
—
0.946
0.929
0.913
0.905
—
—
—
0.957
0.931
0.908
0.886
0.876
0.865
0.846
0.829
0.981
0.946
0.914
0.885
0.858
0.845
0.834
0.812
0.792
0.976
0.931
0.893
0.858
0.827
0.813
0.800
0.775
0.753
60m
70m
80m
Heating capacity correction factors
5m
10m
20m
Refrigerant piping length (one way)
30m
40m
50m
55m
PUHZ-RP35VHA4
1.00
0.997
0.991
0.985
0.979
0.973
0.970
—
—
—
PUHZ-RP50VHA4
1.00
0.997
0.991
0.985
0.979
0.973
0.970
—
—
—
PUHZ-RP60VHA4
1.00
0.997
0.991
0.985
0.979
0.973
0.970
—
—
—
PUHZ-RP71VHA4
1.00
0.997
0.991
0.985
0.979
0.973
0.970
—
—
—
1.00
0.997
0.991
0.985
0.979
0.973
0.970
0.967
0.961
0.955
1.00
0.997
0.991
0.985
0.979
0.973
0.970
0.967
0.961
0.955
1.00
0.997
0.991
0.985
0.979
0.973
0.970
0.967
0.961
0.955
Outdoor unit
PUHZ-RP100VKA
PUHZ-RP100YKA
PUHZ-RP125VKA
PUHZ-RP125YKA
PUHZ-RP140VKA
PUHZ-RP140YKA
7-2. PUHZ-RP200, 250YKA
Cooling capacity correction factors
Outdoor unit
Refrigerant piping length (one way)
5m
10m
20m
30m
40m
50m
55m
60m
PUHZ-RP200YKA
1.00
0.985
0.958
0.931
0.908
0.887
0.876
0.865
PUHZ-RP250YKA
1.00
0.981
0.946
0.914
0.885
0.858
0.845
0.834
Outdoor unit
Refrigerant piping length (one way)
70m
75m
80m
90m
100m
110m
120m
125m
PUHZ-RP200YKA
0.847
0.838
0.829
0.815
0.800
0.790
0.780
0.778
PUHZ-RP250YKA
0.812
0.802
0.792
0.772
0.758
0.743
0.730
0.725
Heating capacity correction factors
Outdoor unit
PUHZ-RP200YKA
PUHZ-RP250YKA
Outdoor unit
PUHZ-RP200YKA
PUHZ-RP250YKA
5m
10m
Refrigerant piping length (one way)
20m
30m
40m
50m
55m
60m
1.00
0.997
0.991
0.973
0.970
0.967
70m
75m
Refrigerant piping length (one way)
80m
90m
100m
110m
120m
125m
0.961
0.958
0.955
0.931
0.928
0.985
0.949
65
0.979
0.943
0.937
8
APPLICABLE EXTENSION PIPE FOR EACH MODEL
8-1. PUHZ-RP·VHA4
PUHZ-RP·VKA PUHZ-RP100-140YKA
8-1-1. PIPE LENGTH
(1) 1:1 SYSTEM
Pipe length
<Table 1> Maximum pipe length
OD
Thickness
OD
Thickness
Liquid
pipe
(mm)
Gas
pipe
(mm)
RP35•50
:6.35
t0.8
:9.52
:12.7
t0.8
t0.8
Standard size
30m +1
50m
[30m]
[30m]
10m
[10m]
RP60•71
:15.88
t1.0
+2
30m
[30m]
:12.7
t0.8
10m
[10m]
30m
[30m]
:9.52
t0.8
:15.88
t1.0
+2
30m
[20m]
Standard size
50m
[30m]
Standard size
50m +3
[30m]
30m
[20m]
RP100~140
:19.05
t1.0
:12.7
t0.8
:19.05
:15.88
t1.0
t1.0
<Marks in the table>
: It can be used.
: Cooling capacity is lowered.
: Additional refrigerant charge is required when
the pipe length exceeds 20m.
50m
[30m]
50m
[20m]
The maximum pipe length
Charge-less pipe length
50m
[30m]
30m
[20m]
50m
[20m]
+1. RP50 : maximum pipe length is 10m.
+2. Change the SW8-1 on the outdoor controller circuit board from OFF to ON.
+3. The maximum length is 75m in case of new pipes.
(2) TWIN AND TRIPLE SYSTEM
(a) TWIN SYSTEM
(b) TRIPLE SYSTEM
<Table 2> Maximum pipe length
<Table 3> Maximum pipe length
RP71(RP35%2)
Main pipe
(mm)
[A]
Liquid pipe
Gas pipe
Liquid pipe
:6.35
Gas pipe
:12.7
:6.35
:12.7
Branch
pipe Liquid pipe :9.52
(mm) Gas pipe :15.88
[B, C]
Liquid pipe :12.7
Gas pipe
RP100(RP50%2)
:9.52
:9.52
:15.88
:15.88
Standard size Standard size
50m
50m +
[30m]
[30m]
50m
[30m]
:9.52
:19.05
:12.7
:19.05
50m
[30m]
50m
[20m]
50m
[30m]
50m
[20m]
50m
[30m]
RP125(RP60%2) • RP140(RP71%2)
:9.52
:15.88
Standard size
50m +
[30m]
:9.52
:19.05
50m
[30m]
RP140(RP50%3)
:12.7
:19.05
Main pipe
(mm)
[A]
50m
[20m]
Branch
pipe Liquid pipe ø9.52
(mm) Gas pipe ø15.88
[B, C, D]
ø9.52 ø9.52
ø15.88 ø19.05
Gas pipe
Liquid pipe ø6.35 Standard size
50m + 50m
Gas pipe ø12.7 [30m] [30m]
Liquid pipe
50m
[20m]
Gas pipe ø19.05
+ The maximum length is 75m in case of new pipes.
+ The maximum length is 75m in case of new pipes.
Indoor unit side
Indoor unit side
Indoor unit
Indoor unit
Indoor unit
B
h
B
C
Indoor unit
C
D
Indoor unit
H
H
Outdoor unit
Distribution pipe
50m
[30m]
50m
[20m]
Liquid pipe ø12.7
:19.05
h
50m
[30m]
ø12.7
ø19.05
Distribution pipe
Outdoor unit side
Outdoor unit side
A
A
<TRIPLE SYSTEM>
Total length A + B + C + D
RP140: 75 m
<TWIN SYSTEM>
Total length A + B + C
RP71
: 50 m
RP100-140: 75 m
66
Outdoor unit
8-1-2. ADJUSTING THE AMOUNT OF REFRIGERANT
• Check additional refrigerant charging amount referring to table 5, 6 when liquid pipe is 1 size larger than standard diameter.
<Table 5> Required additional charge when the pipe size is 1 size larger than the standard diameter (1:1 SYSTEM)
Liquid pipe O.D.
Refrigerant amount to be added
PUHZ-RP35,50
:9.52
60 g per 1 m
PUHZ-RP60,71
:12.7
100 g per 1 m
PUHZ-RP100~140
:12.7
100 g per 1 m
Outdoor unit
<Table 6> Required additional charge when the pipe size is 1 size larger than the standard diameter (TWIN/TRIPLE SYSTEM)
Outdoor unit
When the extension pipe length (main piping + branch piping) exceeds 20 m
PUHZ-RP71~140
Additional refrigerant amount
W(g) = (100 % L1) + (60 % L2) + (30 % L3) - 2000
If the calculation produces a negative number ( W 0), additional charging is not necessary.
L1: :12.7 liquid pipe length (m)
L2: :9.52 liquid pipe length (m)
L3: :6.35 liquid pipe length (m)
<Table 7> Additional refrigerant charging amount for pipe of standard diameter
Additional refrigerant charging amount
Permitted
Amount of unit
for pipe length exceeding 30 m (kg)
Type
Outdoor unit
pipe length filling refrigerant (kg)
31 – 40m 41 – 50m 51 – 60m 61 – 70m 71 – 75m
1:1
PUHZ-RP35,50
system PUHZ-RP71
PUHZ-RP100~140
Type
Outdoor unit
Twin Triple PUHZ-RP71
system PUHZ-RP100~140
50m or less
2.5kg
0.2kg
0.4kg
3.5kg
0.6kg
1.2kg
75m or less
5.0kg
0.6kg
1.2kg
Permitted
pipe length
Amount of unit
filling refrigerant (kg)
50m or less
75m or less
2.4kg
Additional refrigerant charging amount
for pipe length exceeding 30 m (kg)
31 – 40m
41 – 50m
3.5kg
0.6kg
1.2kg
5.0kg
0.6kg
1.2kg
67
1.8kg
51 – 60m
1.8kg
61– 70m
71 – 75m
2.4kg
8-1-3. CAPACITY CORRECTION CURVES
Cooling and heating capacity is lowered according to pipe length. Capacity can be obtained by referring to the capacity
curves below. When the diameter of gas pipe is 1 size smaller than standard diameter, cooling capacity is lowered comparing to the standard diameter. The lowered capacity can be obtained by referring to capacity curves for gas pipe which is
1 size smaller than standard size.
Corrected pipe length (m) = actual pipe length (m) + number of bends x 0.3 (m)
[Sample calculation]
Indoor unit RP60 o 2 units (Twin system)
Outdoor unit RP125 o 1
■ Condition Using existing pipes.
• Outdoor unit side
Liquid pipe [12.7 / Gas pipe [19.05
pipe length (A) 20m
• Indoor unit side
Liquid pipe [9.52 / Gas pipe [15.88
pipe length (B) 20m + (C) 15m
1) Farthest piping length
20m + 15m = 35m
Number of bends : 10
2) Corrected piping length 35m + 0.3 o 10 = 38m
3) Capacity correction
Outdoor unit side’s gas pipe [19.05
Standard [15.88 → 1 size up
Refer to 1 Capacity curves <Standard size>
4) Capacity
Cooling capacity = Standard cooling capacity o 0.89
Heating capacity = Standard heating capacity o 0.98
1 Capacity curves for PUHZ-RP · HA2 model <Standard size>
Cooling
Heating
100
Heating RP35, 50, 60,
71, 100, 125 and 140
models
(Up to 55m for RP35,
50, 60, 71 models)
95
Capacity ratio [%]
Cooling RP35, 60 models
Cooling RP71 model
90
85
Cooling RP50, 100 models
80
Cooling RP125 model
Cooling RP140 model
75
Note: The permitted pipe length is up to 55m for RP35, 50, 60, 71 model.
The permitted pipe length is up to 80m for RP100 ~ 140 model.
70
5
10
15
20
25
30
35
40
45
50
55
Corrected pipe length [m]
68
60
65
70
75
80
2 Capacity curve for PUHZ-RP35, 50 models
<When gas pipe is 1 size smaller than standard size>
Cooling
Heating
100
Heating RP35, RP50 (:9.52)
Capacity ratio [%]
95
90
Cooling RP50
(:9.52)
85
Cooling RP35 (:9.52)
80
5
10
15
20
25
30
35
Corrected pipe length [m]
3 Capacity curve for PUHZ-RP60, 71 models
<When gas pipe is 1 size smaller than standard size>
100
Heating RP60, RP71 (:12.7)
Capacity ratio [%]
95
90
85
80
Cooling RP60,RP71 (:12.7)
5
10
15
20
25
30
35
Corrected pipe length [m]
4 When gas pipe is one size larger than standard size for PUHZ-RP100, 125 and 140.
1 Capacity can be obtained by referring to capacity curves of standard size.
69
8-2. PUHZ-RP200·250YKA
8-2-1. 1:1 SYSTEM
(1) Pipe length
<Table 1> Maximum pipe length (RP200·RP250)
Liquid
pipe
(mm)
O.D.
:9.52
:12.7
:15.88
Thickness
t0.8
t0.8
t1.0
Gas
pipe
(mm)
O.D.
:19.05
:22.2
:25.4
:28.58
:19.05
:22.2
:25.4
:28.58
:22.2
:25.4
:28.58
:31.75
Thickness
t1.0
t1.0
t1.0
t1.0
t1.0
t1.0
t1.0
t1.0
t1.0
t1.0
t1.0
t1.1
RP200
20m
[20m]
50m
[30m]
120m
[30m]
120m
[30m]
20m
[20m]
50m
[30m]
120m
[30m]
120m
[30m]
50m
[20m]
50m
[20m]
50m
[20m]
50m
[20m]
RP250
20m
[20m]
50m
[30m]
120m
[30m]
120m
[30m]
20m
[20m]
50m
[30m]
Standard size
120m
[30m]
120m
[30m]
50m
[20m]
50m
[20m]
50m
[20m]
50m
[20m]
Standard size
Note : Be sure to use hard (tempered) one for pipe over :22.2(RP200)/:19.05(RP250).
<Marks in the table above>
: It can be used.
: Cooling capacity is lowered.
: Additional refrigerant charge is required when
the pipe length exceeds 20m.
120m
[30m]
The maximum pipe length
Charge-less pipe length
(2) Adjusting the amount of refrigerant
Check additional refrigerant charging amount referring to table 7 when the liquid pipe diameter is 1 size larger
than the standard size, and table 2 when the pipe of the standard diameter is used.
<Table 2>
Outdoor unit
RP200
RP250
permitted
pipe length
120m or less
Initial charge
(kg)
Amount of additional refrigerant charge (kg)
30 m and less
7.1
No additional
charge necessary
7.7
31-40 m and less 41-50 m and less 51-60 m and less 61-70 m and less 71-120 m and less
The additional charge
0.9 kg
1.8 kg
2.7 kg
3.6 kg
1.2 kg
2.4 kg
3.6 kg
amount is obtained by
the following formula.
4.8 kg
When length exceeds 70 m
When the total length of the piping exceeds 70 m, calculate the amount of additional charge based on the following requirements.
Note: If the calculation produces a negative number (i.e. a “minus” charge), of if calculation results in an amount that is less than the “Additional charage amount for 70 m”,
perform the additional charge using the amount shown in “Additional charge amount for 70 m”.
Amount of additional
charge
(kg)
=
Main piping:
Liquid line size
ø12.7 overall length ×
0.11
(m) × 0.11 (kg/m)
+
Main piping:
Liquid line size
ø9.52 overall length ×
0.09 (Gas line: ø25.4)
+
Branch piping:
Liquid line size
ø9.52 overall length ×
+
0.06 (Gas line: ø15.88)
(m) × 0.06 (kg/m)
(m) × 0.09 (kg/m)
Branch piping:
Liquid line size
ø6.35 overall length ×
0.02
–
3.6 (kg)
(m) × 0.02 (kg/m)
Additional charge amount RP200 3.6 kg
for 70 meters
RP250 4.8 kg
•If the wiring connecting the indoor and outdoor units is longer than 80m, use separate indoor /outdoor unit
power supplies.
70
(3) Capacity correction
Cooling and heating capacity is lowered according to the piping length. Capacity can be obtained by referring
to the following capacity curves.
When the diameter of the gas pipe is smaller than the standard size, cooling capacity is lowered comparing to
the operation using the standard diameter pipe.
The lowered capacity can be obtained by referring to the capacity curves for gas pipe which is 1 or 2 size
smaller than standard size.
Corrected pipe length (m) = actual pipe length (m) + number of bends o 0.3 (m)
1. Capacity curves 1 <Standard size>
Cooling
Heating
100
Capacity ratio [%]
95
RP200,250
90
85
80
RP200
75
RP250
70
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95 100 105 110 115 120 125
Corrected pipe length [m]
2. Capacity curves 2 <When the gas pipe's diameter is 1-size-smaller than the standard size>
Cooling
Heating
100
RP200, 250(:22.2)
Capacity ratio [%]
95
90
85
80
RP200(:22.2)
75
70
7.5 10
RP250(:22.2)
15
20
25
30
35
40
45
50
55
Corrected pipe length [m]
3. Capacity curves 3 <When the gas pipe's diameter is 2-size-smaller than the standard size>
Cooling
Heating
100
RP200, 250(:19.05)
Capacity ratio [%]
95
90
w RP250
Use 1/2H or H pipes if the diameter
is 19.05.
85
80
RP200(:19.05)
RP250(:19.05)
75
70
7.5
10
15
20
Corrected pipe length [m]
25
71
2. TWIN, TRIPLE AND QUADRUPLE SYSTEM
(1) Twin
Maximum pipe length (Main pipe [A] + Branch pipe diameter [ B and C ])
RP200 twin (RP1002)
RP250 twin (RP1252)
:9.52
:12.7
:15.88
:9.52
:12.7
:15.88
:19.05 :22.2 :25.4 :28.58 :19.05 :22.2 :25.4 :28.58 :22.2 :25.4 :28.58 :31.75 :19.05 :22.2 :25.4 :28.58 :19.05 :22.2 :25.4 :28.58 :22.2 :25.4 :28.58 :31.75
Liquid pipe
Gas pipe
Main pipe
(mm)[A]
Liquid pipe
Gas pipe
Liquid pipe
Branch
pipe Gas pipe
[mm]
Liquid pipe
[B, C]
Gas pipe
:9.52
Standard
size
Standard
size
20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m 20m 50m 120m 120m 20m 50m 120m
:15.88 [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m] [20m] [30m] [30m] [30m] [20m] [30m] [30m]
50m 50m 50m
120m 50m
[30m] [20m] [20m] [20m] [20m]
:9.52
20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m 20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m
:19.05 [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m] [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m]
:12.7
20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m 20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m
:19.05 [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m] [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m]
• Be sure to use hard (tempered) one for pipe over :22.2(RP200)/:19.05(RP250).
(2) Triple
Maximum pipe length (Main pipe [A] + Branch pipe [ B, C and D ])
Main pipe
(mm)[A]
RP200 triple (RP603)
RP250 triple (RP713)
:9.52
:12.7
:15.88
:9.52
:12.7
:15.88
:19.05 :22.2 :25.4 :28.58 :19.05 :22.2 :25.4 :28.58 :22.2 :25.4 :28.58 :31.75 :19.05 :22.2 :25.4 :28.58 :19.05 :22.2 :25.4 :28.58 :22.2 :25.4 :28.58 :31.75
Liquid pipe
Gas pipe
Liquid pipe
Gas pipe
Liquid pipe
Branch
pipe Gas pipe
[mm]
Liquid pipe
[B, C, D]
Gas pipe
:9.52
Standard
size
Standard
size
20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m 20m 50m 120m 120m 20m 50m 120m
:15.88 [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m] [20m] [30m] [30m] [30m] [20m] [30m] [30m]
50m 50m 50m
120m 50m
[30m] [20m] [20m] [20m] [20m]
:9.52
20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m 20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m
:19.05 [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m] [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m]
:12.7
20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m 20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m
:19.05 [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m] [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m]
• Be sure to use hard (tempered) one for pipe over :22.2(RP200)/:19.05(RP250).
(3) Quadruple
Maximum pipe length (Main pipe [A] + Branch pipe [ B, C, D and E ])
Main pipe
(mm)[A]
RP200 quadruple (RP504)
RP250 quadruple (RP604)
:9.52
:12.7
:15.88
:9.52
:12.7
:15.88
:19.05 :22.2 :25.4 :28.58 :19.05 :22.2 :25.4 :28.58 :22.2 :25.4 :28.58 :31.75 :19.05 :22.2 :25.4 :28.58 :19.05 :22.2 :25.4 :28.58 :22.2 :25.4 :28.58 :31.75
Liquid pipe
Gas pipe
Liquid pipe
Gas pipe
Liquid pipe
Branch
pipe Gas pipe
[mm]
Liquid pipe
[B, C, D, E]
Gas pipe
Liquid pipe
Gas pipe
:6.35
Standard
size
20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m
:12.7 [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m]
Standard
size
:9.52
20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m 20m 50m 120m 120m 20m 50m 120m
:15.88 [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m] [20m] [30m] [30m] [30m] [20m] [30m] [30m]
50m 50m 50m 50m
[20m] [20m] [20m] [20m]
:9.52
20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m 20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m
:19.05 [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m] [20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m]
:12.7
20m 50m 120m 120m 20m 50m 120m 120m 50m 50m 50m 50m
[20m] [30m] [30m] [30m] [20m] [30m] [30m] [30m] [20m] [20m] [20m] [20m]
:19.05
• Be sure to use hard (tempered) one for pipe over :22.2(RP200)/:19.05(RP250).
<Marks in the table above>
120m
[30m]
120m
[30m]
: It can be used.
: Cooling capacity is lowered. Refer to <Table6>.
: Additional refrigerant charge is required when
the pipe length exceeds 20m. Refer to <Table7>.
The maximum pipe length
Charge-less pipe length
72
Pipe diameter and thickness
OD
(mm) :6.35
Thickness
0.8
(mm)
:9.52
:12.7
0.8
0.8
:15.88 :19.05
1.0
:22.2
1.0
1.0
:25.4 :28.58
1.0
:31.75
1.0
1.1
Be sure to use hard (tempered) one for pipe over :19.05(RP250)/:22.2(RP200).(Do not use soft (annealed) one.)
B
D
E
Indoor unit
Outdoor unit
Main piping
Branch piping
Multi distribution
pipe (option)
1 Height difference (Indoor unitOutdoor unit) Max. 30 m
2 Height difference (Indoor unitIndoor unit) Max. 1 m
3 Distance between indoor and indoor units
pipe length. Max. 8m
1
2
C
B—C B—D B—E
C—D C—E D—E
A
4 Number of pipe bends
Within 15 points
8 points between main pipe A and
each branch pipe (B, C, D, E).
<Table 6> Lowered cooling capacity by the smaller gas pipe diameter
Cooling capacity ratio
gas pipe :22.2
gas pipe :19.05
100%
100%
100~95%
100~88%
95~88%
88~77%
88~83%
83~79%
79~75%
Pipe length
5m and less
6~10m
11~20m
21~30m
31~40m
41~50m
<Table 7> Additional refrigerant amount when the liquid pipe of the larger diameter is used.
(Single /Simultaneous Twin / Simultaneous Triple / Simultaneous Quadruple)
Capacity
When the extension pipe length (main piping + branch piping) exceeds 20m
RP200, RP250 Additional refrigerant amount W(g)=(180%L1)+(120%L2) (90%L3)+(30%L4)-3000
L1 : :15.88 liquid pipe (m)
L3 : :9.52 liquid pipe (m)
L2 : :12.7 liquid pipe (m)
L4 : :6.35 liquid pipe (m)
If the calculation produces a negative number (i.e. a "minus" charge), additional charging is not necessary.
( W 0)
<Table 8>
Outdoor unit
Permissible total
piping length
A+B+C+D+E
RP200
PR250
120 m and less
A+B or A+C
or
A+D or A+E
100 m and less
Charge-less
piping length
A+B+C+D+E
30 m and less
<Table 9>
Outdoor unit
B-C or B-D or
B-E or C-D or
C-E or D-E
RP200
RP250
8 m and less
Number of
pipe bends
Within 15
73
<Table 10>
Outdoor unit
Permitted
pipe length
RP200
At time of
shipping (kg)
7.1
120m or less
RP250
7.7
30 m and less
No additional
charge necessary
A+B+C+D
Amount of additional refrigerant charge (kg)
31-40 m and less 41-50 m and less 51-60 m and less 61-70 m and less 71-120 m and less
0.9 kg
1.8 kg
2.7 kg
3.6 kg
1.2 kg
2.4 kg
3.6 kg
3.6 kg
The additional charge
amount is obtained by
the following formula.
When length exceeds 70 m
When the total length of the piping exceeds 70 m, calculate the amount of additional charge based on the following requirements.
Note: If the calculation produces a negative number (i.e. a “minus” charge), or if calculation results in an amount that is less than
the “Additional charge amount for 70 m,” perform the additional charge using the amount shown in “Additional charge amount
for 70 m.”
Main piping:
Amount of additional = Liquid line size
charge
:12.7 overall length
0.11
+
Main piping:
Liquid line size
:9.52 overall length
0.09 (Gas line::28.58)
Branch piping: Liquid
Branch piping: Liquid
+ line size
+ line size
–
:9.52 overall length
:6.35 overall length
0.06 (Gas line: :15.88)
0.02 (Gas line: :15.88)
3.6 (kg)
Additional charge amount RP200 3.6 kg
for 70 m
RP250 4.8 kg
1. Perform refrigerant piping connections for the indoor / outdoor unit while the outdoor unit's stop valve is completely
closed (Initial setting), and then vacuumize the refrigerant lines through the service port of the outdoor unit.
2. Open the stop valves of the outdoor unit completely.
This will completely connects the refrigerant circuits of the indoor and outdoor units.
Stop valve opening method is shown on the outdoor unit’s installation manual.
Note :
· Apply refrigerating machine oil over the flare seat surface. Do not apply to the threaded portion.
(It will cause the flare nut to loosen.)
· Use 2 wrenches to tighten piping connection.
· Use leak detector or soapy water to check for gas leaks after connections are completed.
· For the insulation of the connection at the indoor side, make sure to use the attached insulation materials and
thoroughly follow the instruction shown in the manual.
· Always use a non-oxidizing brazing material when brazing the pipes.
Adjusting the amount of refrigerant
Check additional refrigerant charging amount referring to the procedure 2 below when the liquid pipe diameter of the main
piping A is larger than the standard size.
1 When the standard diameter pipe is used for the main piping A, calculate the additional refrigerant amount by
referring to <Table 2> as well as the 1:1 system.
2 When the liquid pipe diameter of the main piping A is one size larger than the standard size:
· When the extension pipe length (main piping + branch piping) does not exceed 20m, adjustment of the
refrigerant is not necessary (charge-less).
· When the extension pipe length (main piping + branch piping) exceeds 20m, charge the amount of refrigerant
that is obtained by the formula shown in <Table 7>.
If the calculation produces a negative number (i.e. a "minus" charge), additional charging is not necessary.
Note: Apply 0 to L1, L2, L3 and L4 which correspond to the liquid pipe size that are not used.
Correcting the capacity value
When calculating the lowered capacity by the extension pipe length, use the longest length between the indoor and the outdoor
units.
74
9
AIR FLOW DATA
9-1. OUTLET AIR SPEED AND COVERAGE RANGE
Airflow
m3/min.
15
18
18
PLA-RP71BA
PLA-RP71BA2
21
Air speed
m/sec.
2.6
3.2
3.2
3.7
5.3
5.4
5.6
m
4.1
4.8
4.8
5.6
8.0
8.2
8.5
PLA-RP35BA
Coverage range
PLA-RP50BA
PCA-RP50KA
PLA-RP60BA
PCA-RP60KA
PLA-RP100BA PLA-RP125BA
PLA-RP140BA2
PLA-RP100BA3 PLA-RP125BA2
30
31
32
PCA-RP71KA PCA-RP100KA PCA-RP125KA PCA-RP140KA
Airflow
m3/min.
15
19
20
28
29
32
Air speed
m/sec.
3.3
3.1
3.2
3.6
3.7
4.1
m
9.0
9.6
10.1
12.5
12.9
14.2
Coverage range
PCA-RP71HA
PCA-RP125HA
Airflow
m3/min.
19
38
Air speed
m/sec.
2.9
4.2
m
7.9
13.2
PKA-RP35HAL
PKA-RP50HAL
Coverage range
Airflow
m3/min.
12
12
Air speed
m/sec.
6.1
6.1
m(ft)
10.8(35.4)
10.8(35.4)
PKA-RP60KAL
PKA-RP71KAL
Coverage range
PKA-RP100KAL
Airflow
m3/min.
22
22
26
Air speed
m/sec.
6.0
6.0
6.8
m(ft)
14.3(46.9)
14.3(46.9)
16.1(52.8)
PSA-RP71GA
PSA-RP100GA
PSA-RP125GA
PSA-RP140GA
Coverage range
Airflow
m3/min.
18
31
33
35
Air speed
m/sec.
2.6
4.5
4.8
4.9
m
8.3
14.3
15.2
16.1
Coverage range
w The air coverage range is the distance to which the 0.25m/sec air can reach, when air is blown out horizontally from the unit
at the High notch position.
The coverage range should be used only as a general guideline since it varies according to the size of the room and the
furniture inside the room.
75
9-2. PLA-RP·BA/BA2/BA3
9-2-1 FRESH AIR INTAKE AND BRANCH DUCT
1. Branch duct hole and fresh air intake hole (Fig. 1)
At the time of i nstallation, use the duct holes ( cut out) located at the positions shown in Fig.1, as and when required.
• A fresh air intake hole for the optional multi function casement can also be made.
Note:
The figure marked with * in the drawing represent the dimensions of the main unit excluding those of the optional
multi function casement.
When installing the optional multi function casement, add 135 mm to the dimensions marked on the figure.
When installing the branch ducts, be sure to insulate adequately.
Otherwise condensation and dripping may occur.
Unit:mm
Fresh air intake hole
Fresh air intake hole diagram
Branch duct hole
3-:2.8 burring hole
:125 burring hole pitch
120
120
Indoor unit
*158
:100 cut out hole
Ceiling
Drain pipe
Refrigerant pipe
100
100
90
130
90
Branch duct
hole diagram
(view from
either side)
100
350
:175 burring hole pitch
Fig. 1
76
*167
70
*155
14-:2.8 burring hole
:150 cut out hole
3. Fresh air intake volume & static pressure characteristics
PLA-RP35~71BA(2)
At using multi-function casement, standard filter
50
Static pressure[Pa]
0
-50
2 - inlet
-100
-150
1 - inlet
-200
0
1
2
3
4
5
6
Airflow rate [m3/min]
At using multi-function casement, high efficiency filter
50
0
0
Static pressure[Pa]
Static pressure[Pa]
Direct intake to unit
50
-50
-100
-150
-200
0
1
2
3
4
5
-50
-100
-150
-200
6
2 - inlet
1 - inlet
0
1
2
3
Airflow rate [m3/min]
3
Airflow rate [m /min]
4
5
6
PLA-RP100BA(3), PLA-RP125,140BA(2)
At using multi-function casement, standard filter
50
Static pressure[Pa]
0
-50
2 - inlet
-100
-150
1 - inlet
-200
0
2
4
Airflow rate [m3/min]
6
8
At using multi-function casement, high efficiency filter
Direct intake to unit
50
50
0
Static pressure[Pa]
Static pressure[Pa]
0
-50
-100
-150
-50
-100
2 - inlet
-150
1 - inlet
-200
0
2
4
Airflow rate [m3/min]
6
-200
8
77
0
2
4
Airflow rate [m3/min]
6
8
4. Change of outlet numbers
Indoor unit
The optional air outlet is necessary.
To change the air outlet number to 3-, or 2-way outlet, the
outlet number should be closed with the operational air
outlet shutter.
When the air outlets are closed, close the vane by
removing the vane connector.
Outlet concave
portion
Button
Vane motor
Up/down vanes
Connector
Air outlet shutter plate
(Option)
Vane motor
Connector
Button
5. Branch duct and change of outlet numbers
+ Branch duct should be connected to one of the branch duct holes on the main unit.
<4- way air flow and branch duct>
Branch
duct
Air intake
Air
outlet
+ Close the outlet on the side of branch duct and air flows in 3 directions.
<3- way air flow and branch duct>
Branch
duct
Air intake
Air
outlet
Air
outlet
closed
position
+ The outlet on the side of branch duct and one of the other outlets are closed.
Air flows in 2 directions.
<2- way air flow and branch duct>
Branch
duct
Air
Air
outlet
outlet
closed
closed
position
position
Air intake
Air
outlet
closed
position
78
PLA-RP71BA PLA-RP71BA2
4-way airflow (horizontal vane) Round duct
4-way airflow (horizontal vane) Rectangular duct
30
Duct
Static pressure [Pa]
Static pressure [Pa]
30
20
10
High
Duct
20
10
High
Low
Low
0
0
0
2
4
6
Airflow rate [m3/min]
0
8
3-way airflow (horizontal vane) Round duct
2
80
70
70
Duct
Duct
60
Close
Static pressure [Pa]
Static pressure [Pa]
60
50
40
30
Close
50
40
30
High
20
20
High
Low
10
0
Low
10
2
4
6
8
Airflow rate [m3/min]
0
10
2-way airflow (horizontal vane) Round duct
0
100
90
90
Duct
2
Duct
80
Close
Close
10
Close
Close
Static pressure [Pa]
70
60
50
40
30
High
20
4
6
8
Airflow rate [m3/min]
2-way airflow (horizontal vane) Rectangular duct
100
80
Static pressure [Pa]
8
3-way airflow (horizontal vane) Rectangular duct
80
0
4
6
Airflow rate [m3/min]
70
60
50
40
30
20
Low
Low
High
10
10
0
0
0
2
4
6
8
10
Airflow rate [m3/min]
0
12
2
4
6
8
10
Airflow rate [m3/min]
• Use 1 of the 2 duct holes on the indoor unit.
• Airflow rate of PLA-RP35~60BA can be calculated from the airflow rate based on the characteristic
of the duct for PLA-RP71BA(2).
• Use the optional air outlet shutter plate (PAC-SH51SP-E) for 3-way and 2-way airflow.
79
12
PLA-RP125BA PLA-RP125BA2
4-way airflow (horizontal vane) Round duct
4-way airflow (horizontal vane) Rectangular duct
30
30
Duct
20
Static pressure [Pa]
Static pressure [Pa]
Duct
10
10
0
0
0
2
4
Airflow rate [m3/min]
6
8
3-way airflow (horizontal vane) Round duct
0
2
4
Airflow rate [m3/min]
6
8
3-way airflow (horizontal vane) Rectangular duct
80
80
70
70
Duct
Duct
Close
Close
60
Static pressure [Pa]
60
50
40
High
50
40
High
30
30
20
20
Low
Low
10
10
0
0
0
2
4
6
Airflow rate [m3/min]
8
0
10
2-way airflow (horizontal vane) Round duct
2
4
6
Airflow rate [m3/min]
8
10
2-way airflow (horizontal vane) Rectangular duct
100
100
90
90
Duct
80
Duct
80
Close
Close
70
70
60
60
Static pressure [Pa]
Static pressure [Pa]
High
Low
High
Low
Static pressure [Pa]
20
50
40
High
30
Close
Close
50
High
40
Low
30
Low
20
20
10
10
0
0
0
2
4
6
8
Airflow rate [m3/min]
10
0
12
2
4
6
8
10
12
Airflow rate [m3/min]
• Use 1 of the 2 duct holes on the indoor unit.
• Airflow rate of PLA-RP100BA(3), PLA-RP140BA2 can be calculated from the airflow rate based on the characteristic
of the duct for PLA-RP125BA(2).
• Use the optional air outlet shutter plate (PAC-SH51SP-E) for 3-way and 2-way airflow.
80
9-3. PCA-RP·KA
Fresh air intake amount & static pressure characteristics
■ PCA-RP60, 71KA
PCA-RP50KA
■
50
50
0
Static pressure[Pa]
Static pressure[Pa]
0
-50
-100
-150
-200
-250
-300
-50
-100
-150
-200
-250
-300
0
1
2
3
0
4
1
Airflow rate[m³/min]
■ PCA-RP100, 125, 140KA
A
-50
Q
-100
-150
Duct characteristics
at site
2
C
A
-200
E
-250
2
3
4
Q
Airflow rate[m³/min]
D
3
A
1
Q
Qa
81
C
0
0
Static pressure[Pa]
Curve in the
graphs
B
50
0
3
4
How to read curves
1
-300
2
Airflow rate[m³/min]
Q…Designed amount of fresh air intake
<m3/min>
A…Static pressure loss of fresh air
intake duct system with airflow
amount Q
<Pa>
…
B Forced static pressure at air conditioner
inlet with airflow amount Q
<Pa>
C…Static pressure of booster fan with
airflow amount Q
<Pa>
D…Static pressure loss increase amount
of fresh air intake duct system for
airflow amount Q
<Pa>
E…Static pressure of indoor unit with
airflow amount Q
<Pa>
Qa … Estimated amount of fresh air
3
intake without D
<m /min>
9-4. PEAD-RP·JA(L)
Fan performance
PEAD-RP35JA(L)
(External static pressure 100Pa) 220-240V 50Hz
PEAD-RP35JA(L)
(External static pressure 35Pa) 220-240V 50Hz
120
60
110
Rated point
100
Limit
External static pressure (Pa)
External static pressure (Pa)
50
40
Rated point
High
30
Middle
20
Low
10
Limit
90
High
80
70
Middle
60
50
Low
40
30
20
10
0
7
9
11
13
15
17
19
0
21
7
9
11
Airflow rate(m3/min)
13
PEAD-RP35JA(L)
(External static pressure 50Pa) 220-240V 50Hz
17
19
21
PEAD-RP35JA(L)
(External static pressure 150Pa) 220-240V 50Hz
70
170
160
Rated point
150
60
140
Limit
External static pressure (Pa)
External static pressure (Pa)
15
Airflow rate(m3/min)
Rated point
50
High
40
Middle
30
Low
20
Limit
130
High
120
110
100
Middle
90
80
70
Low
60
50
40
30
10
20
10
0
7
9
11
13
15
17
19
0
21
Airflow rate(m3/min)
90
80
External static pressure (Pa)
Rated point
Limit
High
60
50
Middle
40
Low
30
20
10
0
7
9
11
13
15
9
11
13
15
Airflow rate(m3/min)
PEAD-RP35JA(L)
(External static pressure 70Pa) 220-240V 50Hz
70
7
17
19
21
Airflow rate(m3/min)
82
17
19
21
PEAD-RP50JA(L)
(External static pressure 100Pa) 220-240V 50Hz
PEAD-RP50JA(L)
(External static pressure 35Pa) 220-240V 50Hz
130
70
120
110
60
50
High
40
Rated point
Middle
30
Low
20
Rated point
Limit
100
External static pressure (Pa)
External static pressure (Pa)
Limit
90
High
80
70
Middle
60
50
Low
40
30
20
10
10
0
9
14
0
19
9
14
19
Airflow rate(m3/min)
Airflow rate(m3/min)
PEAD-RP50JA(L)
(External static pressure 50Pa) 220-240V 50Hz
PEAD-RP50JA(L)
(External static pressure 150Pa) 220-240V 50Hz
180
80
170
160
70
External static pressure (Pa)
External static pressure (Pa)
Rated point
50
High
140
High
60
Middle
40
30
Rated point
150
Limit
Low
20
Limit
130
120
110
Middle
100
90
80
Low
70
60
50
40
10
30
20
0
9
14
10
19
0
Airflow rate(m3/min)
9
14
Airflow rate(m3/min)
PEAD-RP50JA(L)
(External static pressure 70Pa) 220-240V 50Hz
100
90
External static pressure (Pa)
80
Limit
Rated point
70
High
60
50
Middle
40
30
Low
20
10
0
9
14
19
Airflow rate(m3/min)
83
19
PEAD-RP60JA(L)
(External static pressure 100Pa) 220-240V 50Hz
PEAD-RP60JA(L)
(External static pressure 35Pa) 220-240V 50Hz
120
60
110
50
Rated point
100
External static pressure (Pa)
External static pressure (Pa)
Limit
40
Rated point
30
High
20
Middle
90
Limit
High
80
70
Middle
60
50
Low
40
30
Low
10
20
10
0
10
15
20
25
0
10
30
15
Airflow rate(m3/min)
20
PEAD-RP60JA(L)
(External static pressure 50Pa) 220-240V 50Hz
170
160
Rated point
150
Limit
140
Rated point
50
External static pressure (Pa)
External static pressure (Pa)
30
PEAD-RP60JA(L)
(External static pressure 150Pa) 220-240V 50Hz
70
60
25
Airflow rate(m3/min)
High
40
Middle
30
20
Low
High
130
Limit
120
110
100
Middle
90
80
70
60
Low
50
40
30
10
20
10
0
10
15
20
25
0
30
Airflow rate(m3/min)
90
80
Rated point
External static pressure (Pa)
Limit
High
60
50
Middle
40
30
Low
20
10
0
10
15
20
15
20
Airflow rate(m3/min)
PEAD-RP60JA(L)
(External static pressure 70Pa) 220-240V 50Hz
70
10
25
30
Airflow rate(m3/min)
84
25
30
PEAD-RP71JA(L)
(External static pressure 100Pa) 220-240V 50Hz
PEAD-RP71JA(L)
(External static pressure 35Pa) 220-240V 50Hz
70
130
120
60
High
110
Rated point
50
External static pressure (Pa)
External static pressure (Pa)
100
Limit
High
40
Rated point
30
Middle
20
Low
Limit
90
Middle
80
70
60
Low
50
40
30
10
20
10
0
10
15
20
25
0
30
10
15
Airflow rate(m3/min)
20
25
30
Airflow rate(m3/min)
PEAD-RP71JA(L)
(External static pressure 50Pa) 220-240V 50Hz
PEAD-RP71JA(L)
(External static pressure 150Pa) 220-240V 50Hz
90
180
170
High
160
80
Rated point
150
140
External static pressure (Pa)
External static pressure (Pa)
70
Limit
60
High
Rated point
50
Middle
40
30
Low
20
130
Middle
Limit
120
110
100
90
80
Low
70
60
50
40
30
10
20
10
0
10
15
20
25
0
30
Airflow rate(m3/min)
100
90
High
External static pressure (Pa)
80
Limit
Rated point
70
Middle
50
40
Low
30
20
10
0
10
15
20
15
20
Airflow rate(m3/min)
PEAD-RP71JA(L)
(External static pressure 70Pa) 220-240V 50Hz
60
10
25
30
Airflow rate(m3/min)
85
25
30
PEAD-RP100JA(L)
(External static pressure 100Pa) 220-240V 50Hz
PEAD-RP100JA(L)
(External static pressure 35Pa) 220-240V 50Hz
70
150
140
Limit
130
60
External static pressure (Pa)
External static pressure (Pa)
120
50
40
Rated point
30
High
Middle
20
Low
High
Limit
110
Rated point
100
90
Middle
80
70
Low
60
50
40
30
10
20
10
0
10
15
20
25
30
35
40
0
45
Airflow rate(m3/min)
90
External static pressure (Pa)
External static pressure (Pa)
Limit
70
High
Rated point
50
Middle
40
Low
30
20
25
30
35
40
45
PEAD-RP100JA(L)
(External static pressure 150Pa) 220-240V 50Hz
100
60
15
Airflow rate(m3/min)
PEAD-RP100JA(L)
(External static pressure 50Pa) 220-240V 50Hz
80
10
20
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
40
High
Rated point
Limit
Middle
Low
30
20
10
0
10
0
10
15
20
25
30
35
40
45
PEAD-RP100JA(L)
(External static pressure 70Pa) 220-240V 50Hz
120
110
External static pressure (Pa)
100
Limit
High
90
80
Rated point
Middle
70
60
Low
50
40
30
20
10
0
10
15
20
25
30
35
40
10
15
20
25
30
Airflow rate(m3/min)
Airflow rate(m3/min)
45
Airflow rate(m3/min)
86
35
40
45
PEAD-RP125JA(L)
(External static pressure 100Pa) 220-240V 50Hz
PEAD-RP125JA(L)
(External static pressure 35Pa) 220-240V 50Hz
70
180
170
Limit
160
High
60
External static pressure (Pa)
External static pressure (Pa)
High
140
50
Low
40
Limit
150
Middle
Rated point
30
20
130
120
110
100
90
80
Middle
Rated point
Low
70
60
50
40
30
10
20
10
0
15
20
25
30
35
40
0
45
15
20
Airflow rate(m3/min)
90
High
External static pressure (Pa)
External static pressure (Pa)
Limit
70
Middle
50
Rated point
Low
40
30
20
10
0
15
20
25
30
35
40
45
PEAD-RP125JA(L)
(External static pressure 70Pa) 220-240V 50Hz
150
140
130
External static pressure (Pa)
High
Limit
110
100
90
Middle
80
70
Rated point
Low
60
50
40
30
20
10
0
15
20
25
30
35
230
220
210
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
40
45
High
Limit
Middle
Rated point
Low
15
20
25
30
35
Airflow rate(m3/min)
Airflow rate(m3/min)
120
35
PEAD-RP125JA(L)
(External static pressure 150Pa) 220-240V 50Hz
100
60
30
Airflow rate(m3/min)
PEAD-RP125JA(L)
(External static pressure 50Pa) 220-240V 50Hz
80
25
40
45
Airflow rate(m3/min)
87
40
45
PEAD-RP140JA(L)
(External static pressure 100Pa) 220-240V 50Hz
PEAD-RP140JA(L)
(External static pressure 35Pa) 220-240V 50Hz
70
190
180
170
160
150
Limit
60
50
External static pressure (Pa)
External static pressure (Pa)
High
Middle
40
Low
Rated point
30
20
High
Limit
140
130
120
Middle
110
100
90
Rated point
80
70
60
50
Low
40
10
0
30
20
15
20
25
30
35
40
10
0
15
45
Airflow rate(m3/min)
90
High
External static pressure (Pa)
External static pressure (Pa)
Limit
Middle
60
Low
50
Rated point
40
30
20
10
0
15
20
25
30
35
40
45
50
Airflow rate(m3/min)
150
140
130
External static pressure (Pa)
Limit
110
High
100
90
Middle
80
70
Rated point
60
Low
50
40
30
20
10
0
15
20
25
30
35
35
240
230
220
210
200
190
180
170
160
150
140
130
120
110
100
90
80
70
60
50
40
30
20
10
0
40
45
High
Limit
Middle
40
45
Airflow rate(m3/min)
88
Rated point
Low
15
20
25
30
35
Airflow rate(m3/min)
PEAD-RP140JA(L)
(External static pressure 70Pa) 220-240V 50Hz
120
30
PEAD-RP140JA(L)
(External static pressure 150Pa) 220-240V 50Hz
100
70
25
Airflow rate(m3/min)
PEAD-RP140JA(L)
(External static pressure 50Pa) 220-240V 50Hz
80
20
40
45
9-5. PEA-RP·GA
Fan Performance Curve
PEA-RP250GA
Fan Performance Curve 50Hz
PEA-RP200GA
Fan Performance Curve 50Hz
(Pa)
(Pa)
250
300
External static pressure
External static pressure
250
200
Hi
150
100
Lo
50
0
45.0
50.0
55.0
60.0
65.0
200
150
100
Lo
50
0
60.0
70.0 (CMM)
Hi
65.0
70.0
75.0
Airflow
85.0
90.0 (CMM)
PEA-RP500GA
Fan Performance Curve 50Hz
(Pa)
300
(Pa)
350
250
300
External static pressure
External static pressure
PEA-RP400GA
Fan Performance Curve 50Hz
200
150
100
50
0
70.0
80.0
Airflow
250
200
150
100
50
80.0
90.0
100.0
110.0
120.0
130.0
(CMM)
Airflow
0
100.0
110.0
120.0
130.0
140.0
Airflow
89
150.0
160.0
170.0
(CMM)
NOISE CRITERION CURVES
10
10-1. INDOOR UNIT
PLA-RP35BA
NOTCH SPL(dB)
High
31
Medium1
29
Medium2
28
Low
27
LINE
PLA-RP50BA
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
NC-20
250
500
1000
2000
4000
10
8000
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
NC-20
125
250
BAND CENTER FREQUENCIES, Hz
PLA-RP60BA
NOTCH SPL(dB)
High
32
Medium1
31
Medium2
29
Low
28
LINE
PLA-RP71BA
PLA-RP71BA2
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
1000
2000
4000
8000
NOTCH SPL(dB)
High
34
Medium1
32
Medium2
30
Low
28
LINE
90
80
10
500
BAND CENTER FREQUENCIES, Hz
90
20
LINE
90
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
90
NOTCH SPL(dB)
High
32
Medium1
31
Medium2
29
Low
28
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
8000
BAND CENTER FREQUENCIES, Hz
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
90
4000
8000
PLA-RP100BA
PLA-RP100BA3
NOTCH SPL(dB)
High
40
Medium1
37
Medium2
34
Low
32
LINE
PLA-RP125BA
PLA-RP125BA2
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
NC-20
125
250
500
1000
2000
4000
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
8000
BAND CENTER FREQUENCIES, Hz
PLA-RP140BA2
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
BAND CENTER FREQUENCIES, Hz
NOTCH SPL(dB)
High
44
Medium1
42
Medium2
39
Low
36
LINE
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
90
UNIT
80
CEILING
70
NC-70
60
NC-60
1.5m
50
NC-50
40
NC-40
30
NC-30
20
10
LINE
90
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
90
NOTCH SPL(dB)
High
41
Medium1
39
Medium2
36
Low
34
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
8000
BAND CENTER FREQUENCIES, Hz
91
MICROPHONE
8000
PEAD-RP·JA(L)
Ceiling concealed
2m
Aux.duct
1.5m
2m
Measurement location
Noise level at anechoic room (Low-Middle-High) Unit: dB(A)
Model
Exrernal static pressure
35Pa
50Pa
70Pa
100Pa
150Pa
PEAD-RP35JA(L)
23-26-29
23-27-30
24-28-31
26-29-33
29-33-37
PEAD-RP50JA(L)
25-30-34
26-31-35
28-32-36
29-33-37
31-35-39
PEAD-RP60JA(L)
25-28-32
25-29-33
26-30-34
27-31-35
29-34-38
PEAD-RP71JA(L)
25-29-34
26-30-34
27-31-35
28-32-36
30-35-39
PEAD-RP100JA(L)
28-33-38
29-34-38
30-35-39
31-36-40
34-40-43
PEAD-RP125JA(L)
31-36-40
33-36-40
33-37-41
34-39-42
37-41-45
PEAD-RP140JA(L)
33-37-43
34-38-43
34-39-44
36-40-45
38-42-46
92
PEAD-RP35JA(L)
External static pressure 35Pa
70
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
External static pressure 100Pa
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
63
BAND CENTER FREQUENCIES, Hz
70
NC-70
NC-60
50
NC-50
40
NC-40
30
NC-30
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
2000
4000
8000
4000
8000
93
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
80
1000
70
0
8000
BAND CENTER FREQUENCIES, Hz
External static pressure 70Pa
500
80
60
20
250
External static pressure 150Pa
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
125
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
External static pressure 50Pa
NC-20
10
0
8000
High
Middle
Low
4000
8000
PEAD-RP50JA(L)
External static pressure 35Pa
70
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
External static pressure 100Pa
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
63
BAND CENTER FREQUENCIES, Hz
70
NC-70
NC-60
50
NC-50
40
NC-40
30
NC-30
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
2000
4000
8000
4000
8000
94
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
80
1000
70
0
8000
BAND CENTER FREQUENCIES, Hz
External static pressure 70Pa
500
80
60
20
250
External static pressure 150Pa
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
125
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
External static pressure 50Pa
NC-20
10
0
8000
High
Middle
Low
4000
8000
PEAD-RP60JA(L)
External static pressure 35Pa
70
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
External static pressure 100Pa
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
63
BAND CENTER FREQUENCIES, Hz
70
NC-70
NC-60
50
NC-50
40
NC-40
30
NC-30
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
2000
4000
8000
4000
8000
95
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
80
1000
70
0
8000
BAND CENTER FREQUENCIES, Hz
External static pressure 70Pa
500
80
60
20
250
External static pressure 150Pa
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
125
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
External static pressure 50Pa
NC-20
10
0
8000
High
Middle
Low
4000
8000
PEAD-RP71JA(L)
External static pressure 35Pa
70
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
External static pressure 100Pa
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
63
BAND CENTER FREQUENCIES, Hz
70
NC-70
NC-60
50
NC-50
40
NC-40
30
NC-30
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
2000
4000
8000
4000
8000
96
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
80
1000
70
0
8000
BAND CENTER FREQUENCIES, Hz
External static pressure 70Pa
500
80
60
20
250
External static pressure 150Pa
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
125
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
External static pressure 50Pa
NC-20
10
0
8000
High
Middle
Low
4000
8000
PEAD-RP100JA(L)
External static pressure 35Pa
70
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
External static pressure 100Pa
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
63
BAND CENTER FREQUENCIES, Hz
70
NC-70
NC-60
50
NC-50
40
NC-40
30
NC-30
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
2000
4000
8000
4000
8000
97
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
80
1000
70
0
8000
BAND CENTER FREQUENCIES, Hz
External static pressure 70Pa
500
80
60
20
250
External static pressure 150Pa
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
125
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
External static pressure 50Pa
NC-20
10
0
8000
High
Middle
Low
4000
8000
PEAD-RP125JA(L)
External static pressure 35Pa
70
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
External static pressure 100Pa
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
63
BAND CENTER FREQUENCIES, Hz
70
NC-70
NC-60
50
NC-50
40
NC-40
30
NC-30
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
2000
4000
8000
4000
8000
98
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
80
1000
70
0
8000
BAND CENTER FREQUENCIES, Hz
External static pressure 70Pa
500
80
60
20
250
External static pressure 150Pa
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
125
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
External static pressure 50Pa
NC-20
10
0
8000
High
Middle
Low
4000
8000
PEAD-RP140JA(L)
External static pressure 35Pa
70
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
External static pressure 100Pa
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
63
BAND CENTER FREQUENCIES, Hz
70
NC-70
NC-60
50
NC-50
40
NC-40
30
NC-30
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
0
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
2000
4000
8000
4000
8000
99
High
Middle
Low
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
Approximate
minimum audible
limit on continuous
noise
NC-20
10
63
125
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
80
1000
70
0
8000
BAND CENTER FREQUENCIES, Hz
External static pressure 70Pa
500
80
60
20
250
External static pressure 150Pa
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
125
BAND CENTER FREQUENCIES, Hz
High
Middle
Low
External static pressure 50Pa
NC-20
10
0
8000
High
Middle
Low
4000
8000
SOUND LEVELS
Low-Middle-High
Model
Sound level dB (A)
PKA-RP35, 50HAL
36 - 40 - 43
PKA-RP60, 71KAL
39 - 42 - 45
PKA-RP100KAL
41 - 45 - 49
PKA-RP35HAL
PKA-RP50HAL
PKA-RP60KAL
PKA-RP71KAL
External static pressure : 0Pa
Power source : 220, 230, 240V, 50Hz
70.0
70.0
High
Low
60.0
NC-60
55.0
50.0
NC-50
45.0
40.0
NC-40
35.0
30.0
20.0
NC-30
Approximate minimum
audible limit on
continuous noise
NC-20
15.0
10.0
63
125
250
500
1k
2k
Octave band center frequencies (Hz)
4k
8k
60.0
NC-60
55.0
50.0
NC-50
45.0
40.0
NC-40
35.0
30.0
NC-30
25.0
20.0
Approximate minimum
audible limit on
continuous noise
15.0
10.0
63
NC-20
125
250
500
1k
2k
Octave band center frequencies (Hz)
4k
8k
PKA-RP100KAL
External static pressure : 0Pa
Power source : 220, 230, 240V, 50Hz
70.0
UNIT
WALL
1m
1m
MICROPHONE
High
Low
65.0
Octave band pressure level (dB) 0dB=20μPa
25.0
High
Low
65.0
Octave band pressure level (dB) 0dB=20μPa
65.0
Octave band pressure level (dB) 0dB=20μPa
External static pressure : 0Pa
Power source : 220, 230, 240V, 50Hz
60.0
NC-60
55.0
50.0
NC-50
45.0
40.0
NC-40
35.0
30.0
NC-30
25.0
20.0
Approximate minimum
audible limit on
continuous noise
15.0
10.0
63
125
250
NC-20
500
1k
2k
Octave band center frequencies (Hz)
100
4k
8k
PCA-RP50KA
NOTCH SPL(dB)
40
High
37
Medium1
34
Medium2
32
Low
PCA-RP60KA
LINE
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
10
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
PCA-RP71KA
NOTCH SPL(dB)
High
41
Medium1
39
Medium2
37
Low
35
63
125
500
1000
2000
4000
NOTCH SPL(dB)
High
43
Medium1
41
Medium2
39
Low
37
PCA-RP100KA
LINE
8000
LINE
90
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
250
BAND CENTER FREQUENCIES, Hz
90
10
NC-20
10
8000
BAND CENTER FREQUENCIES, Hz
20
LINE
90
90
20
NOTCH SPL(dB)
High
40
Medium1
37
Medium2
35
Low
33
80
70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
8000
NC-70
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
BAND CENTER FREQUENCIES, Hz
BAND CENTER FREQUENCIES, Hz
101
8000
PCA-RP125KA
NOTCH SPL(dB)
High
45
Medium1
43
Medium2
41
Low
39
PCA-RP140KA
LINE
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
80
10
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
8000
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
PCA-RP71HA
NOTCH SPL(dB)
High
38
Low
34
LINE
500
1000
2000
4000
8000
NOTCH SPL(dB)
High
50
Low
44
LINE
90
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
250
PCA-RP125HA
90
10
NC-20
BAND CENTER FREQUENCIES, Hz
BAND CENTER FREQUENCIES, Hz
20
LINE
90
90
20
NOTCH SPL(dB)
High
48
Medium1
45
Medium2
43
Low
41
80
70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
NC-20
10
63
125
250
500
1000
2000
4000
NC-70
8000
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
500
ceiling
1m
unit
about 1.4m
MICROPHONE
250
1000
2000
BAND CENTER FREQUENCIES, Hz
BAND CENTER FREQUENCIES, Hz
1m
NC-20
102
4000
8000
PSA-RP71GA
NOTCH SPL(dB)
45
High
40
Low
LINE
PSA-RP100GA
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
APPROXIMATE
THRESHOLD OF
REARING FOR
CONTINUOUS
NOISE
63
125
80
70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
NC-20
250
500
1000
2000
4000
NC-70
APPROXIMATE
THRESHOLD OF
REARING FOR
CONTINUOUS
NOISE
10
8000
63
125
PSA-RP125GA
NOTCH SPL(dB)
High
51
Low
46
LINE
500
1000
2000
4000
8000
NOTCH SPL(dB)
High
52
Low
47
LINE
90
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
APPROXIMATE
THRESHOLD OF
REARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
8000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
250
PSA-RP140GA
90
10
NC-20
BAND CENTER FREQUENCIES, Hz
BAND CENTER FREQUENCIES, Hz
20
LINE
90
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
90
NOTCH SPL(dB)
High
49
Low
44
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
APPROXIMATE
THRESHOLD OF
REARING FOR
CONTINUOUS
NOISE
20
10
63
BAND CENTER FREQUENCIES, Hz
125
NC-20
250
500
1000
2000
BAND CENTER FREQUENCIES, Hz
unit
MICROPHONE
1m
1m
floor
103
4000
8000
10-2. OUTDOOR UNIT
MICROPHONE
1m
UNIT
1.5m
GROUND
MODE SPL(dB)
COOLING
44
HEATING
46
90
LINE
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
10
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
NC-20
125
250
500 1000 2000 4000
BAND CENTER FREQUENCIES, Hz
PUHZ-RP100VKA
PUHZ-RP100YKA
MODE SPL(dB)
COOLING
49
HEATING
51
LINE
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
PUHZ-RP125VKA
PUHZ-RP125YKA
1000
2000
4000
8000
MODE SPL(dB)
COOLING
50
HEATING
52
LINE
90
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
8000
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
70
BAND CENTER FREQUENCIES, Hz
80
10
LINE
80
8000
90
20
MODE SPL(dB)
COOLING
47
HEATING
48
90
80
20
PUHZ-RP60VHA4
PUHZ-RP71VHA4
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
PUHZ-RP35VHA4
PUHZ-RP50VHA4
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
BAND CENTER FREQUENCIES, Hz
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
BAND CENTER FREQUENCIES, Hz
104
8000
MODE
COOLING
HEATING
SPL(dB)
50
52
LINE
PUHZ-RP200YKA
90
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
MODE SPL(dB)
COOLING
58
HEATING
59
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
8000
BAND CENTER FREQUENCIES, Hz
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
BAND CENTER FREQUENCIES, Hz
PUHZ-RP250YKA
MODE SPL(dB)
COOLING
58
HEATING
59
LINE
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
90
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
10
LINE
90
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
OCTAVE BAND SOUND PRESSURE LEVEL, dB (0 dB = 0.0002 μbar)
PUHZ-RP140VKA
PUHZ-RP140YKA
APPROXIMATE
THRESHOLD OF
HEARING FOR
CONTINUOUS
NOISE
63
125
NC-20
250
500
1000
2000
4000
8000
BAND CENTER FREQUENCIES, Hz
105
8000
11
OPTIONAL PARTS
11-1. INDOOR UNIT
Part Name
Model Name
Applicable model
Remote sensor
PAC-SE41TS-E
All models
Remote operation adapter
Multiple remote controller adapter
PAC-SF40RM-E
PAC-SA88HA-E (1pc.)
PAC-725AD (10pcs.)
Remote on/off adapter
Power supply terminal kit
All models except PEA-RP400/
500GA
PAC-SE55RA-E
L/N/Earth
L/N
PAC-SG96HR-E
PCA-RP·KA, PSA-RP·GA
PAC-SG94HR-E
PKA-RP·HAL/KAL
PAC-SH52HR-E
PAC-SG97HR-E
PLA-RP·BA/BA2/BA3
Decoration panel
PLP-6BA
Decoration panel with Wireless remote controller
PLP-6BALM
Decoration panel with Wired remote controller
PLP-6BAMD
Decoration panel with i-see sensor
PLP-6BAE
PCA-RP·HA
PEAD-RP·JA(L)
Decoration panel with i-see sensor, Wireless remote controller PLP-6BALME
Decoration panel with i-see sensor, Wired remote controller
PLP-6BAMDE
Automatic filter elevation panel
PLP-6BAJ
i-see sensor corner panel
PAC-SA1ME-E
Wireless signal receiver
PAR-SA9FA-E
Space panel
PAC-SH48AS-E
Air outlet shutter plate
PAC-SH51SP-E
Multi-function casement
PAC-SH53TM-E
Flange for fresh air intake
High-efficiency filter element
(PAC-SH53TM-E is needed.)
Wireless remote controller kit
Drain pump
PAC-SH65OF-E
PAC-SH59KF-E
High-efficiency filter
Duct flange for fresh air
Oil mist filter element (12pcs)
Decoration cover
(Front + Suspending bracket cover)
Wired remote controller
(with terminal bed)
Drain pump
Filter box
PLA-RP·BA/BA2/BA3
PAR-SL94B-E
PCA-RP·KA
PAC-SH83DM-E
PCA-RP50KA
PAC-SH85DM-E
PCA-RP60KA
PAC-SH84DM-E
PCA-RP71,100, 125, 140KA
PAC-SH88KF-E
PCA-RP50KA
PAC-SH89KF-E
PCA-RP60, 71KA
PAC-SH90KF-E
PAC-SF28OF-E
PCA-RP100, 125, 140KA
PCA-RP·HA
PAC-SG38KF-E
PAC-SF81KC-E
PCA-RP71HA
PAC-SF82KC-E
PAR-21MAAT-E
PCA-RP125HA
PKA-RP·HAL
PKA-RP·KAL
PAC-SH75DM-E
PKA-RP·HAL
PAC-SH94DM-E
PKA-RP·KAL
PAC-KE92TB-E
PEAD-RP35, 50JA(L)
PAC-KE93TB-E
PEAD-RP60, 71JA(L)
PAC-KE94TB-E
PEAD-RP100, 125JA(L)
PAC-KE95TB-E
PEAD-RP140JA(L)
106
11-2. OUTDOOR UNIT
Part Name
Model Name
Applicable model
M-NET adapter
PAC-SF81MA-E
PUHZ-RP35-250
A-control service tool
PAC-SK52ST
PUHZ-RP35-250
Drain socket
PAC-SG61DS-E
PUHZ-RP35-250
PAC-SG58SG-E
PUHZ-RP35, 50
Air outlet guide (RP100-250 need 2 pieces.)
Air protect guide (RP100-250 need 2 pieces.)
Drain pan
PAC-SG59SG-E
PUHZ-RP60, 71
PAC-SH96SG-E
PUHZ-RP100-250
PAC-SG56AG-E
PUHZ-RP35, 50
PAC-SH63AG-E
PUHZ-RP60, 71
PAC-SH95AG-E
PUHZ-RP100-250
PAC-SG63DP-E
PUHZ-RP35, 50
PAC-SG64DP-E
PUHZ-RP60, 71
PAC-SH97DP-E
PUHZ-RP100-250
PAC-SG81DR-E
PUHZ-RP35, 50
Filter dryer
([6.35)
([9.52)
PAC-SG82DR-E
PUHZ-RP60-200
PAC-SG85DR-E
PUHZ-RP250
Distribution pipe
([12.7)
(Twin)
MSDD-50TR-E
PUHZ-RP71-140
MSDD-50WR-E
PUHZ-RP200, 250
(Triple)
MSDT-111R-E
PUHZ-RP140-250
(Quadruple)
MSDF-1111R-E
PUHZ-RP200, 250
Joint pipe (Unit
Extension pipe)
([15.88
[19.05) PAC-SG75RJ-E
PUHZ-RP60-140
([9.52
[12.7)
PAC-SG73RJ-E
PUHZ-RP60-200
([12.7
[15.88)
PAC-SG74RJ-E
PUHZ-RP250
([6.35
[9.52)
PAC-SG72RJ-E
PUHZ-RP35-50
107
TM
HEAD OFFICE : TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
CCopyright 2009 MITSUBISHI ELECTRIC ENGINEERING CO., LTD.
Distributed in Jul. 2009 No.OCS16 PDF 6
Made in Japan
New publication, effective Jul. 2009
Specifications subject to change without notice.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement