RSTKE-900 Operation Manua1

RSTKE-900 Operation Manua1
RSTKE-900
PROFESSIONAL 915 MHz REMOTE CAR
STARTER & 6 CHANNEL KEYLESS ENTRY
SYSTEM
With
Two Way Serial Port Data Link
Optional two Way Up grade Available
Compatible
OPERATION MANUAL
Please register your product at:
www.autopageusa.com
THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY
1
Auto Page, Inc. has over 25 years of experience in the vehicle security industry
in the United States and is a wholly owned subsidiary of Iwata Electric Co., of
Tokyo, Japan. Iwata has been an industry leader for over 50 years,
establishing a reputation for ingenuity in its engineering capability and
innovative communication products. Auto Page and Iwata maintain a long
tradition of providing the best value to their customers.
CHANGING THE BATTERY IN YOUR TRANSMITTERS
XT-90S:
This transmitter uses one (1) 3-volt lithium ion battery (#CR2032)
that is placed with the (+) side facing upward. To replace the battery, you will
need to use a small flat blade screwdriver and a small Philips screwdriver.
Remove the small Philips head screw. Then locate the small notch on the
lower right side of the transmitter case next to the key ring. Using the flat blade
screwdriver, carefully pry the top case from the bottom case. It should snap
apart after breaking the seal. Before removing the battery note the direction of
the positive (+) terminal. Place the new battery in exactly the same manner,
being careful not to bend or damage the contact terminal. Snap the cases
back together and then test the transmitter to insure it arms and disarms the
alarm. Reinstall the Philips screw to finalize the battery replacement.
XT-90S Extended Range Sliding Cover remote
CR2032 3-Volt Battery
2
WARNINGS:
As with any product that performs automatic functions, there are certain safety
precautions that you must practice and be aware of.
1.
2.
3.
4.
5.
6.
7.
Keep the transmitter out of children’s reach.
Do not leave anyone in the vehicle while running on remote control.
Alert servicing personnel that the vehicle can be started automatically.
Do not start the vehicle by remote while it’s in an enclosed area or garage.
Always apply the parking brake and lock the vehicle as you exit the vehicle.
The vehicle windows must be rolled up.
Should the unit malfunction, disconnect the fuse until the problem is
corrected.
8. The use and operations of this system is the sole responsibility of the
operator.
9. Some areas may have local ordinances that prohibit leaving a vehicle
running on public streets.
10. It is not safe to remote start the vehicle if the vehicle is parked on a steep
incline.
OPERATION:
A. REMOTE TRANSMITTER OPERATION:
Transmitter
Button
System Function
Remark
Lock Doors
Press and Hold for 3 seconds.
Panic function
Press the
Car Locator
button to stop.
Under armed mode
Unlock Doors
-
+
Two Steps Door Unlock &
Disarm System
Press twice within 3 seconds.
Trunk Release (Channel 3)
Press and Hold for 2 seconds
Activate or Turn Off The
Remote Start
Press twice within 3 seconds if programmed
for safety start
Channel # 4 Timer Output (4)
+
Channel # 5 Timer Output (5)
+
Channel # 6 Timer Output (6)
ACTIVE LOCK:
3
1. Press
button on the transmitter.
2. The horn, if installed will chirp once and parking lights will flash once
indicating that the system is now active. The vehicle doors will lock upon
activating when interfaced with the keyless entry system.
ACTIVE UNLOCK:
1. Press
button on the transmitter.
2. The horn will chirp twice and parking light will flash twice to indicating
that the keyless system is now unlocked. The vehicle doors will unlock
and dome lights will turn on for 30 seconds.
PATHWAY ILLUMINATION:
This feature turns the parking light “ON” for 30 seconds upon an unlock
signal and for 10 seconds upon the lock signal. (Programmable)
TWO STEPS DOOR UNLOCK: (programmable) (optional)
This feature will independently unlock the driver’s door only when
disarming the security system. Pushing the
button a second time
within 3 seconds will unlock the other doors.
DEACTIVATING WITHOUT A TRANSMITTER:
The Override function may be used if ht e remote transmitter is lost or
inoperative.
1. Enter the vehicle and turn the ignition switch to ‘ON’ position.
2. Within 10 seconds push and release the valet switch
VALET MODE:
The valet switch allows you to temporarily bypass all system function,
eliminating the need to hand your transmitter to parking attendants or
garage mechanics. When the system is in valet mode, and remote
start functions are bypassed, Enter Valet Mode:
1.From the Unlock condition, turn the ignition to “ON” position.
2.Push and hold valet switch for 2 seconds until the LED turns on. The
LED will remain on as long as the system is in ‘valet mode’.
Exit Valet Mode:
1. Return to normal operation, turn ignition ‘on’.
2. Push and hold valet switch for 2 seconds, The LED will turn off
indicating the system has exited the valet mode.
4
CAR LOCATOR
Under armed mode, press the
button to activate the car locator
function. The horn, if installed will chirp 6 times. The parking light will
flash 12 times, for you to easily locate your car.
PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger the
alarm in case of an emergency.
1. Press and hold the
button for 3 second. The horn if installed will
immediately sound.
2. During panic mode, the normal function of this transmitter button will
be disabled. The transmitter
and
buttons can be used to lock
and unlock the door (if the option is installed), however once the
button is pressed, the vehicle’s starter disable device, (where
installed) will be disengaged allowing the vehicle to start.
3. To stop the alarm, press and hold the transmitter
or
button on the
transmitter again for 3 seconds or press
or
to stop immediately.
If the button is not pressed, the alarm will automatically stop after 30
seconds.
TRUNK RELEASE (CHANNEL 3) OUTPUT.
Press and hold
button on the transmitter for three seconds to remotely
release the trunk or other electric devices.
IGNITION CONTROL DOOR LOCK/UNLOCK.
If the vehicles power door locks have been interfaced to the unit, the
system will automatically lock the vehicle's doors in 3 seconds when the
ignition is turned “ON” and /or unlock the vehicle’s doors when the
ignition is turned “OFF”. (Programmable)
CHANNEL 4 TIMER CONTROL OUTPUT
5
Pressing the transmitter
and
button at the same time will activate
the Channel 4 function. Channel 4 is user -programmable timer output. You
may program the built-in timer to send a ground signal for any time duration
from 1 second to 120 seconds. For instance, this timer output may be used
to turn on the headlight, power window or sunroof. (Factory defaults setting
at momentary output.)
CHANNEL 5 TIMER CONTROL OUTPUT
Pressing the transmitter
and
buttons at the same time will activate
the Channel 5 function. Channel 5 is user-programmable timer output. You
may program the built-in timer to send a ground signal for any time duration
from 1 second to 120 seconds. For instance, this timer output may be used to
turn on the headlight, power window or sunroof. (Factory defaults setting at
momentary output.
CHANNEL 6 TIMER CONTROL OUTPUT
Pressing the transmitter
and
buttons at the same time will activate
the Channel 6 function. Channel 6 is user-programmable timer output. You
may program the built-in timer to send a ground signal for any time duration
from 1 second to 120 seconds. For instance, this timer output may be used to
turn on the headlight, power window or sunroof.
(Factory defaults setting at momentary output.)
SECOND VEHICLE SECURITY OPERATION:
Your 5-button remote transmitter can be utilized to control a second ve hicle
security system, To program the remote control transmitter to a second
vehicle, follow the instructions for Transmitter programming.
II
Switching code For 2nd Car
Operation.
For regular remote transmitter
Only
OPTIONAL TWO WAY UPGRADE:
This system can be easily upgraded by purchasing a compatible two
way remote control for this system. Two way communication will allow
you to have access to vehicle information and condition as well as
confirmation of all sent commands.
The XT-90 LCD and XT-100 OLED are both compatible with the
RSTKE-900 and can be purchased from an authorized Autopage dealer.
To view these transmitters go to www.autopageusa.com .
.
REMOTE START OPERATION:
6
TO REMOTE START THE VEHICLE:
When you want to start your vehicle,
1. Press
button once on the transmitter.
2. The parking lights will activate to indicate the remote start received
the signal.
3. The engine will start in approximately 5 seconds.
4. Once the engine is running and after couple seconds the parking
lights will turn on again and climate controls will activate and adjust the
vehicles interior temperature to your preset setting. (While the vehicle is
running, the “minutes” digit on the LCD screen will flash and will indicate
a count down timer based on the 5, 10, 20 or 30 minute run time set up
by your installation center.)
5. The vehicle will run for 5 to 30 minute cycle and automatically shut
down. (When the unit shuts off the count down timer will turn off and the
transmitter will play a melody sound.)
NOT E: The Remote Start Unit will not start the vehicle if any one of the
following conditions exists:
1. The hood is opened.
2. The brake pedal is pressed.
3. The remote start enable toggle switch is in the OFF position. (If
installed)
4. The gear selector is in any gear other then “PARK” or “NEUTRAL”
SAFE START (Child safety mode) (programmable)
The factory default setting to start the vehicle is to press the
button
ONCE on the transmitter. Programming this feature to eliminate an
accidental remote start operation,
1. The user must press the transmitter
button twice within 3
seconds to start the vehicle. or
2. The user must press the transmitter
time to start the vehicle.
and
buttons at the same
TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE
START:
To operate the vehicle while the engine is running on the remote start:
1. Ins ert the ignition key and turn it to “ON” (not the start) position.
2. Press the brake pedal.
Note: If the brake pedal is pressed before the key is in the ON position,
the engine will shut down.
TEMPORARY STOP FEATURE:
7
This feature allows the vehicle to remain running after the key has been
removed from the ignition. This feature is useful for occasions when you
wish to exit and lock the vehicle for short periods of time, but would like
to leave the motor running and the climate control on.
1. Before turning off the engine, press the
button on the transmitter
and the LED indicator will flash 3 times to confirm entry.
2. Turn the ignition key to OFF position. (The engine will stay running.)
3. The engine will run until the pre-programmed time has elapsed or
shutdown input is received. If the brake pedal is depressed the engine
will stop.
TURBO CHARGE MODE: (programmable)
Turbo charge mode keeps the engine running after arriving at your
destination for a programmable period of 1, 3 or 5 minutes. This allows
the vehicle’s engine time to conveniently cool down the turbo after you
have left the vehicle. To activate:
1. While the engine is running, pull up the hand brake and place the
transmission gear in the park position.
2. Before turning off the engine, press and release
and
buttons at
the same time.
-- The LED will flash indicating the remote start has entered the turbo
charge mode.
3. Take the “Ignition Key” from the key cylinder.
-- Engine keeps running. -4. Exit and secure the vehicle.
-- Engine continues running until the pre-programmed time has
elapsed. -NOTE: This feature only applies to vehicles with Turbo Engines.
TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it,
1. Press
button once on the remote transmitter while in the remote
start mode.
2. Press the brake pedal. The vehicle will shut down and turn off the
parking lights will indicate engine has stopped
3. Move the optional remote start enable toggle switch to OFF position. (If
installed)
SHUT-DOWN INPUT FOR REMOTE STARTER:
8
If any of the following conditions exist while the system is operating, the
engine will not start or will shut down immediately:
1. The hood is opened.
2. The brake pedal is pressed.
3. Engine is over-revved. {“Tachometer checking type” only}
4. The pre-programmed run time (5 /10 / 20 / 30 minutes) has elapsed.
5. Press
button once on the remote transmitter under remote start
mode.
6. The optional remote start enable toggle switch is in the OFF position. (If
installed)
7. The vehicle refused to start running after {3} unsuccessful attempts.
DISABLING THE REMOTE START SYSTEM:
(Toggle switch If installed)
This feature allows your system’s remote start unit to be temporarily
disabled to prevent the vehicle from being remote started accidentally.
This feature is useful if the vehicle is being serviced or stored in an
enclosed area. To disable the remote start, move the optional remote
start enable toggle switch to the OFF position.
LIMITED LIFETIME WARRANTY PROVISIONS
( U.S. ,Continental U.S. and Canada Only)
1.
Auto Page, Inc. WARRANTS that this new unit has been thoroughly
inspected and tested at the factory prior to delivery. Your Auto Page
equipment is guaranteed for “life” to the original purchaser/user of the
equipment and the original vehicle in which it was installed by an
authorized installer under the following conditions: If the product proves
defective (according to Auto Page's testing) within the first year, the
defective unit may be exchanged or repaired free of charge. “Proof of
Purchase” (dated sales receipt) must accompany all warranty returns;
otherwise, your return will be rejected and sent back. After one (1)
year, the purchaser should ship the unit prepaid to Auto Page with a
money order in the amount of $30.00 to cover shipping and handling
charges. Note: The product needs to be registered online at time of
installation. www.autopageusa.com
2.
This WARRANTY will be considered void if the equipment has been
misused, neglected, improperly serviced or installed, altered, dropped
or damaged by water, contrary to the Auto Page OPERATIONS
MANUAL. Or, if used with accessories not approved by Auto Page,
which may have contributed to the defect. See note below regarding
product installation**.
9
3.
The purchaser’s remedies under this WARRANTY shall be limited to
the repair or replacement of electronic components only. THE
FOLLOWING IS NOT COVERED: Damages or deterioration to cases,
batteries, covers and cabinets; the cost of repairs, replacement and
labor of which shall be borne by the purchaser even if occurring during
the WARRANTY period.
4.
Any equipment or parts which are claimed to be defective under this
WARRANTY must be sent to the Auto Page Service center with “proof
of purchase” at the purchaser’s expense prior to such return, a Return
Authorization Number should be obtained. Auto Page will return the
equipment, charges prepaid. Warranty Service can be provided
through the dealer where the equipment is originally purchased.
5.
Any unexpired WARRANTY shall be applicable to equipment and parts
in the possession of the original purchaser only.
6.
THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER
WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITED TO ANY WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE.
7.
Auto Page shall not be liable, under the foregoing WARRANTIES or
otherwise, for: Any personal injury of any kind to the purchaser, its
employees or agents or anyone else whomsoever resulting directly or
indirectly from the use or presence of the equipment or parts;
Consequential damages of any kind; any inability of the purchaser to
use the equipment.
**IMPORTANT NOTE: Any damages to the alarm system resulting
from an installation performed by anyone other than a professional
installation technician authorized by a dealer of Auto Page will void
the product’s limited lifetime warranty.
Auto Page Warranty:
You must register your product online at
http://www.autopageusa.com to receive any warranty service.
Please go to the customer service tab and select product registration.
It is the purchaser’s responsibility to register this product for any future
warranty service.
Warning: Some batteries may contain Perchlorate
10
It is recommended to have a minimal digital service plan on your cell phone
Your RSTKE-900 is CI3 compatible and will open your world to the
true power of two way communication. Complete tracking and full
cell phone functionality can be added to your system. For more
11
information please visit your local authorized Autopage dealer or go
to www.autopageusa.com .
Compatible
2-Way Communication to the Power of 3
960 Knox Street Unit B, Torrance, CA 90502
Tel: (310) 323-1800 or (800) 262-2527 www.autopageusa.com
12
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement