Manual_EN - SecurityMan Inc
SecurityMan®
Network Edition
4CH Triplex Digital Video Recorder
SecurityMan
®
User's Manual
NDVR-04
Copyright
2
© Copyright 2005
This manual is furnished under license and may be used or copied only in accordance with the terms of such license.
Except as permitted by such license, no part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or any
means, electronic, mechanical, recording, or otherwise, including translation to another language or format, without the prior written permission of Part.
The content of this manual is furnished for informational use only, is subject to change without Notice, and should not be construed as a commitment
by SecurityMan Inc,. SecurityMan Inc,. assumes no responsibility or liability for any errors or inaccuracies that may appear in this book.
FCC Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
Operation of this equipment in a residential area is likely to cause interference in which case the user at his or her own risk and expense will be
required to correct the interference.
Declaration of Conformity
SecurityMan declares that the DVR-04 conforms to the following standards, in accordance with the provisions of the EC Directive 89/366/EEC: EN
55022 (CISPR 22:1985), Class A.
Warranty
SecurityMan Inc,. warrants that this product will be free from defects in title, materials and manufacturing workmanship for one year from the date of
the purchase. If the product is found to be defective then, as your sole remedy and as the manufacturer’s only obligation, SecurityMan will repair or
replace the product.
This warranty is exclusive and is limited to DVR-04. This warranty shall not apply to products that have been subjected to abuse, misuse, abnormal
electrical or environmental conditions, or any condition other than what can be considered normal use.
Warranty Disclaimers
SecurityMan Inc,. makes no other warranties, express, implied or otherwise, regarding the DVR-04, and specifically disclaims any warranty for merchantability or fitness for a particular purpose.
The exclusion of implied warranties is not permitted in some states and the exclusions specified herein may not apply to you. This warranty provides
you with specific legal rights. There may be other rights that you have which vary from state to state.
Limitation of Liability
The liability of SecurityMan Inc,. arising from this warranty and sale shall be limited to a refund of the purchase price. In no event shall SecurityMan be
liable for costs of procurement of substitute products or services, or for any lost profits, or for any consequential, incidental, direct or indirect damages,
however caused and on any theory of liability, arising from this warranty and sale. These limitations shall apply not with standing any failure of essential purpose of any limited remedy.
For Customer Service: 888-977-3777
SecurityMan
4601 E. Airport Drive, Ontario, CA 91761, USA
Tel: 888-977-3777 Tel: 909-230-6668 Fax: 909-230-6889
Email: info@securitymaninc.com
Website: http://www.securitymaninc.com
Copyright 2006 by SecurityMan v1.5F
Contents
1
3
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Front Panel Key Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Rear Panel Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2 DVR Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Video Output Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Video Input Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Sensor Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Alarm Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3 Operation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Full Screen or Quad Screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Zoom Mode (Display Enlargement) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PIP (Picture in Picture) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
USB Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Freeze Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Watermark Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Playback Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Rec Start/Stop Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Event List Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Time/Date Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
4 On Screen Display Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
System Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Time/Date Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
HDD Format Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Auto Sequence Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Factory Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Play Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Video Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Buzzer sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Password Enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
New password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Video Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Name Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
BRI/CON Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Boundary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Background. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Record set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Network Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..... 19
Sensor Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Firmware Update. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Schedule Set. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Contents
5
4
Network Viewer Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
To Install Network Viewer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
To Uninstall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
How to Use Network Viewer client software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Live View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Scandisk. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Fileplay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6
Recording Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Important Message. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Recording time formula. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Recording size per field . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Recording time table at PAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Recording time table at NTSC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Introduction
5
The Digital Video Recorder (DVR) is for recording video streams up to 4 channels all at the same
time. It adopts the digital image compression technology to compress the video streams into digital
signals and uses HDD for recording. The following operation guide explains how to operate and
manage the DVR while the installation guide explains how to install the DVR and how to add HDD
into the DVR.
Hope you will enjoy it, use it to protect your home, and eventually make your home safe.
Front Panel Key Function
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
18)
USB_ BACKUP : Backup recorded data to USB memory via USB port on the rear of the DVR.
INFO : Display current setting information of the DVR; HDD information, software version, etc.
PIP : Picture in Picture
ZOOM : Zoom into the current active image.
FULL/SEPARATE : Full screen of CH1, CH2, CH3 & CH4.
Press and hold for 3 seconds to activate 9 split screen.
QUAD : Display images in QUAD view.
Press and hold for 3 seconds to activate auto dwell between cameras.
Rewind : Reverse playback
Forward: Fast Forward
Up: Browse up or choose between the three type of watermark during playback mode.
Down : Browse down
IR Remote Sensor
Enter: Select or confirm
Menu : Setup Mode, Menu
Playback/Pause
Stop: Stop playback.
Recording: Start or end recording.
Power on LED indicator: Solid Green
Recording LED indicator: Flashes Red on record.
Installation
6
Rear Panel Function
1)
USB2.0: Flash Drive
2)
S-Video(Y/C) video output connector
3)
VIDEO-OUT( BNC VIDEO OUTPUT CONNECTOR)
4)
VIDEO-IN (BNC CAMERA INPUT)
5)
VIDEO-LOOP OUTPUT (CAMERA LOOP OUT)
6)
4 sensor inputs and one alarm output
7)
DC-IN 12V, 4.2A, positive inside
8)
Audio channel input x 1 and audio output x 1
9)
LAN network port
10)
Power switch
11)
NDVR FAN
12)
CALL-OUT: Auto dwell video output to 2nd or son-monitor
DVR Installation
7
Video Output connection to TV or monitor
Please connect the TV or monitor input source to the video-out located on the back of the DVR.
This unit provide an S-Video and 2BNC output connectors. Video output are used primary for
monitoring and toggle between full screen and quad screen display. The call out connector is used
for a 2nd or a son-monitor output to display full screen single channel with auto sequencing mode,
no quad view. The figure below illustrate the connection between the DVR and the monitor output.
Out to TV
S-Video out to TV
Video Input connection (Camera Input)
Please connect camera video cable to the DVR video input port. This unit provide 4 x
BNC video input connectors port. The camera installation procedures are as following:
Connecting the camera video: connect the camera video cable to the DVR's VIDEO-IN.
Connecting the camera power: connect camera’s A/C adapter to the camera, and plug the
adaptor into a power outlet. The complete connection illustration with a camera are
shown in the figure below.
Signal line
Camera
Power line
AC/DC adapter
Power outlet
DVR Installation
8
Sensor Installation
This unit contains 4 sensor inputs in which each sensor corresponds to the 4 channels. The sensor
installation procedures are as follow. There are two simple step in installing the sensors.
connecting the sensor signal line: connect the sensor signal line to DVR. The sensor signal terminal
is located on the rear panel of the DVR.
Then Connect the sensor jack to the sensor, and plug in the adaptor to an electrical outlet to power up sensor.
IN1
IN2
IN3
IN4
Alarm (output)
Note: Each sensor corresponds to each camera channel, for example, alarm input #1 will
correspond to channel #1 and so on.
Alarm (output) Installation
The unit provides 1 internal switch to sound the alarm when the sensor is activated. The switch is open at normal
state a wiring diagram as shown below. When the alarm is activated, the switch is closed so that the alarm gets the
power. The circuitry is shown as in the below figure. There are two simple steps to install the alarm.
a) Prepare the power supply for the alarm by connecting the power adapter from the camera to the power
outlet.
b) Connect the alarm power line to the alarm output terminal located on the back of the DVR as shown below.
Signal Line
Power
Power outlet
AC/DC adaptor
Alarm
NOTICE: Sensor input is RECOGNIZED as LOW when alarm
signal is on the same level with GND, and it is recognized as
HIGH when alarm signal is Floating or 5V, following the internal
circuit. Thus, circuitry can be damaged, when the sensor input
goes to a Negative level or voltage higher than 5V.
5
V
D1
Operation Guide
9
Full screen or quad screen display
Press QUAD button to display quad screen. Press and hold the button for 3 seconds to enter auto
sequence display mode. To adjust the screen sequence auto dwell time between each channel,
please go to SYSTEM SETUP into AUTO SEQUENCE SET into MON SEL: DISPLAY
Press FULL/SEPARATE button to display the selected camera image in full screen, i.e. CAM 1,
CAM 2, CAM 3 or CAM 4 individually in full screen display.
Press FULL/SEPARATE button and hold for 3 seconds to display 9 split screen. The split screen
display live video images monitoring, see if the live video images are in record mode or not, and
able to view and control the history playback file. The “PB CH1~PB CH4” in the split screen below
displays the playback channels and the “CAM 1~CAM 4” show live video image display. The 9 split
screen allows viewing flexibility; ability to live monitor, show recording status and playback video
images all at the same time.
12/11
/2006 12:06:34MON CAM 1
PB CH1
PB CH2
PB CH3
PB CH4
CAM 3
CAM 4
CAM 2
Zoom Mode (Display Enlargement)
During the live view: Go to full screen mode by pressing the FULL/SEPARATE button, and then press
the STOP button. The freeze symbol F will appear on upper right corner of the screen. Then, press the
ZOOM button, the zoom symbol Z , will appear on the top right corner of the screen next to F . Now you
can use the directional buttons to locate the zoomed position up/down, or left/right. Press
ENTER at any time to enlarge the selects location and ENTER again to zoom out.
During playback mode: Go to full screen mode by pressing the FULL/SEPARATE button, then press
the STOP button, follow by the zoom button. The symbol Z will appear on top right corner. Now you
can use the directional buttons to locate the zoomed position and press ENTER to zoom in and
ENTER again to zoom out.
PIP (Picture in picture)
Press PIP to enter picture in picture mode. Figures 3.1 through 3.3 display the output screen when PIP
is pressed once, twice and third time .
Figure 3.1
Fig 3.1
CAM2
Figure 3.3
Fig 3.2
Information
CAM1
Fig 3.3
Figure 3.2
CAM2
CAM1
CAM3
CAM1
CAM2
CAM3 CAM4
Operation Guide
10
Information
Press INFO to get the following on screen display information; system setting, HD, firmware, etc.
0000
MASTER
SLAVE
HDD MODEL: Maxtor
NO DETECT
HDD Capital: 40G
HDD USED: 0.07%
HDD READ: 0.07%
PB REPEAT: OFF
OVERWRITE: ON
REC SPEED: 50 Fld/1sec
REC Letter: HIGH
V. FORMAT: PAL
IP ADDR: 010 192 001 124
S/W Ver: CR04U Vxx.xx
USB Back-Up ( To back up data into USB Flash drive)
Note1 : Video backup can only be done during Playback mode.
Sub-Note : This button can be used to reset the DVR to manufacturer default setting. For example: if
by default the video mode is NTSC standard and PAL is accidentally selected, the video output will
roll vertically, or if password is forgotten. If in such cases, this button can be used to default all setting
back to the original manufacture setting. To reset to manufacture default setting; power off the DVR,
press and hold the “USB BACKUP” button while tuning on the DVR power switch, continue to hold
down on the “USB_BACKUP” button for 5 seconds, after 5 seconds release the “USB_BACKUP”
button and then restart the DVR by using the power switch off and on.
a) Step One: Check available space of USB Flash Drive.
Plug a USB flash drive into the USB port on the rear panel of the DVR . Press MENU button
and choose FW UPDATE only to see the available space on the USB flash drive for backup.
Then press the MENU button to escape from FW UPDATE menu. Please note the USB flash
drive recommended use is 2GB which is the maximum capacity the DVR is capable of detecting.
Drives that are larger than 2GB capacity can be use but, depending on the capacity size of the flash
drive the backup speed will vary during backup.
b) Step Two: Choose a video file section to save
Press PLAY/PAUSE button, and the Search Mode will appear on screen. Please select between
REC START /STOP SEARCH, EVENT LIST SEARCH, or TIME/DATA SEARCH, and press
ENTER to confirm the selection. During Playback Mode, press USB_BACKUP button to save
the desired snapshot or video to the USB flash drive at anytime during playback. There are
two methods of backup: the first method is to press the USB BACKUP button once for
snapshots picture, and the second method is to press and hold the USB BACKUP button for
3 seconds for video clips backup. During these process an “S” will appear on the screen when
attempting to do snapshots backup and an “A" will appear on the screen when attempting to
do video clips backup.
Note 2 : video USB backup can take anywhere from 3 seconds up to 45 seconds before if starts the
backup. For faster backup we recommend to use flash drives that are below 2G B in size. The larger
flash drive, the slower the backup
Operation Guide
11
Freeze Mode
During the live camera view, press the stop button to freeze the image. The symbol F will appear
on the top right hand corner of the screen. The freeze command can be use in both single channel
view or quad channel view.
Watermark Mode
Watermark protection feature: It is to prevent any modification of the recorded data file . If there is
modification; the watermark will not look the same. The watermark will automatically be added during
the recording stage, whether or not they are visible or invisible mark . There are 3 types of watermarks
to choose from as preferred below.
During playback mode, press the UP button once to activate the invisible watermark. Press the UP
button twice to activate the visible watermark; the visible watermark symbols will appear on the screen
as WTNMK as shown in the middle figure below. Finally by pressing the UP button third time to
activate the watermark as shown in last figure below. Most commonly used watermark is visible WTNMK.
Invisible WTNMK
W T
W T
M
M
N
K
Visible WTNMK
N
K
WTNMK
Playback Mode
Press Play/Pause button, and the SEARCH MODE will appear on screen as illustrated below.
SEARCH MODE
◎ REC START / STOP SEARCH
□ EVENT LIST SEARCH
□ TIME / DATE SEARCH
------------------------------------------------------------ENTER SET ↑↓← → EXIT
Press the UP/DOWN button to browse and select one of the 3 search methods to playback recorded
video files.
12
Operation Guide
REC START/STOP SEARCH(Search by Start/Stop Time recording):
RECORD SEARCH MASTER
START TIME
04/06/2006 14:43
05/06/2006 03:10
05/06/2006 10:05
PAGE:0001/9999
END TIME
04/26/2006 14:46
05/06/2006 03:45
05/06/2006 10:23
------------------------------------------------------------ENTER SET ↑↓← → EXIT
START TIME: MM / DD / YYYY HH: MM (start of recorded file)
END TIME: MM / DD / YYYY HH: MM (End of recorded file)
The DVR can store up to 10 files to a page and 100 pages maximum. The total files listing
up to 1000. The START/STOP listing delete the rectangular box. are arranged in order by time
and date.
Press the directional button UP/DOWN to select a file and press [ENTER] to confirm the
selection and start the playback.
EVENT LIST SEARCH:
EVENT SEARCH MASTER
PAGE:0001/9999
EVENT
CH
MOTION
3+4
NETWORK
ALARM
START TIME
09/21/2005 13:02:18
09/21/2005 12:59:42
09/21/2005 12:45:53
CH1
Select EVENT LIST SEARCH to search for Alarm event, motion event, schedule event,
and network event (recorded over network client software, Netviewer).
EVENT LIST can display up to 10 event files to a page and there are 100 pages which
total up to 1000 event lists.
START TIME: MM / DD / YYYY HH: MM: SS (Event start time)
EVENT: includes Alarm / Motion / Schedule / Network.
CH: CH 1, CH 2, CH 3, CH 4 (Event channel occurring channel(s))
Press the UP/DOWN directional buttons to select a file and press ENTER to confirm the
selection.
TIME / DATE SEARCH:
TIME SEARCH
HDD: MASTER
START: 10 / 04 / 2005 12 : 37
END: 10 / 13 / 2005 18 : 22
10/13/2005
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
U
17:22
U
U
U
U
U
U
U
U
On Screen Display Functions
13
Select TIME/DATE SEARCH to search for specific time/date by inputting the
MM/YYYY HH: MM into the search, the search engine will start to search for the specified
time and date.
START: MM / DD / YYYY HH: MM (start/earliest date/time
that exists in the hard drive)
:
END: MM / DD / YYYY HH: MM (End/last date/time that exist in the hard drive)
M M / D D / Y Y Y Y H H : M M (this date/time area is adjustable for search). Press the Forward/
Reverse button to select column digits and press UP/DOWN to change the value. Press
the ENTER button to start playback.
NOTE: Playback speed can be change with the Forward/Reverse button. The speed
can be of x1, x2, x4, x8, x16 times for rewind and x1, x2, x4, x8, x16, x32 times for fast
forward.
Basic Operation
Press the MENU button to enter the SETUP MODE, a variety of menu entities will appear as shown below:
SETUP MODE
◎ SYSTEM SET [
□ VIDEO SET [
]
]
□ RECORD SET [
]
□ NETWORK SET [
]
□ SENSOR SET [
]
□ BACKUP SET [
]
□ SCHEDULE SET [
]
Press the UP/DOWN buttons to highlight selection and press ENTER to confimr selection and the
sub-menu will appear. Press the MENU button to return to the previous screen or to exit from
the setup mode.
SYSTEM SET
Press the MENU button to enter SETUP MODE. Choose SYSTEM SET and press ENTER to
access the sub-menu display as illustrated below.
SYSTEM SETUP
SETUP MODE
◎ SYSTEM SET [
□ VIDEO SET [
◎ TIME/DATE SET [
]
□ HDD FORMAT SET [
]
□ RECORD SET [
]
□ SENSOR SET [
]
□ BACKUP SET [
]
]
□ AUTO SEQUENCE SET [
]
□ NETWORK SET [
]
]
□ SCHEDULE SET [
------------------------------------------------------------ENTER SET ↑↓← → EXIT
]
□ FACTORY RESET [
]
□ PLAY REPEAT: NO
□ VIDEO SOURCE: PAL
□ BUZZER SOUND: ON
□ PASSWORD ENA: OFF
□ NEW PASSWORD: 0000
------------------------------------------------------------ENTER SET ↑↓← → EXIT
On Screen Display Functions
14
TIME/DATE SET
In the SYSTEM SETUP menu, select TIME/DATE SET and press [ENTER]. Press the UP/DOWN buttons
to change the value. Press the FORWARD /REVERSE to select number category. Press MENU/ESC to
return to SYSTEM setup.
TIME/DATE SET
DATE: 0 4 / 2 6 / 2 0 0 6
TIME: 1 5 : 4 3 : 5 1
DAY: TUE
FORMAT: MM / DD / YYYY(3 choice)
DISPLAY: ON/OFF
LOCAL: TOP/ BUT
---------------------------------------------------------------ENTER SET ↑↓← → EXIT
There are three TIME/DATE format display setting to choose from. TIME/DATE display setting can be
turn on or off or set to display at the top or at the bottom of the on screen display.
HDD FORMAT SET
In the SYSTEM SETUP menu, select HDD FORMAT SET and press ENTER. The warning screen
below will appear. Choose YES or NO by pressing the FORMARD/REUERSE buttons then press
ENTER to accept. Press MENU/ESC to return to the SYSTEM SETUP menu .
HDD FORMAT SET
Attention
Do you want to erase the HDD?
Yes NO
---------------------------------------------------------------ENTER SET ↑↓← → EXIT
AUTO SEQUENCE SET
In the SYSTEM SETUP menu, select AUTO SEQUENCE SET and press ENTER. Press the
directional buttons UP/DOWN to select the camera channel and the FORWARD/REVERSE buttons to
change the sequential dwell time for each channel display. Press MENU/ESC to return to SYSTEM SETUP
AUTO SEQUENCE SET
MON SEL: DISPLAY
- CH1 : 01 SEC
- CH2 : 01 SEC
- CH3 : 01 SEC
- CH4 : 01 SEC
---------------------------------------------------------------ENTER SET ↑↓← → EXIT
MON SEL: CALL is auto sequence dwell time setting used for 2nd or Son-monitor output.
On Screen Display Functions
15
FACTORY RESET
In the SYSTEM SETUP menu, select FACTORY RESET and press ENTER. A warning screen will
appear as shown below. Select YES or NO by pressing the FORWARD/REVERSE buttons then press
ENTER to confirm selection. Press the MENU/ESC to return to the SYSTEM SETUP menu page.
FACTORY RESET
Attention
Do you want to initialize?
Yes NO
---------------------------------------------------------------ENTER SET ↑↓← → EXIT
PLAY REPEAT
In the SYSTEM SETUP menu, select PLAY REPEAT. Then press the Forward/Reverse buttons to
select between YES or NO. Press MENU/ESC to return to the SETUP MODE menu or press UP/DOWN
directional buttons to browse to the system setup. Repeat play can be used to play cycle playback file.
SYSTEM SETUP
◎ TIME/DATE SET [
◎ HDD FORMAT SET [
]
]
◎ AUTO SEQUENCE SET [
]
◎ FACTORY RESET [
]
◎ PLAY REPEAT: NO
◎ VIDEO SOURCE: PAL
◎ BUZZER SOUND: ON
◎ PASSWORD ENA: OFF
◎ NEW PASSWORD: 0000
------------------------------------------------------------15
ENTER SET ↑↓← → EXIT
VIDEO SOURCE
In the SYSTEM SETUP menu, select VIDEO SOURCE. Use the directional buttons FORWARD/
REVERSE toggle between NTSC or PAL video format and press MENU/ESC to return to the SETUP
MODE or press the UP/DOWN directional buttons to browse to the next system setup.
Warning: Before switching from NTSC to PAL, please make sure that you are living outside of:
United states of america, alaska, american samoa, antigua, antilles (dutch), aruba, bahamas, barbados, barbuda, belize, bermuda, bolivia(ntsc m n), british virgin islands, burma, canada, caymen
islands(pal / ntsc), chile (ntsc-m), columbia, costa rica cuba, curacao, diego garcia, dominica, dominican republic, ecuador, el salvador, galapagos island, greenland(ntsc / pal), grenada, guam, guatemala, guyana (republic), haiti, hawaii, honduras, jamaica, japan, johnston islands, korea south,
leeward islands, mariana islands, marshall islands, mexico, micronesia, midway islands, montserrat,
myanmar, nicaragua, okinawa, palau, panama, peru, philippines, puerto rico, samoa, st kitts and
nevis, st lucia, st vincent, surinam, taiwan, trinidad & tobago, veneauela, vietnam(ntsc / secam(v)),
and virgin islands.
On Screen Display Functions
16
SYSTEM SETUP
◎ TIME/DATE SET [
]
]
◎ HDD FORMAT SET [
◎ AUTO SEQUENCE SET [
]
◎ FACTORY RESET [
]
◎ PLAY REPEAT: NO
◎ VIDEO SOURCE: PAL
◎ BUZZER SOUND: ON
◎ PASSWORD ENA: OFF
◎ NEW PASSWORD: 0000
------------------------------------------------------------ENTER SET ↑↓← → EXIT
If the video standard setting is not set up correctly, resetting the DVR is required to default back to
NTSC standard. To default: turn off the DVR, press and hold the USB_BACKUP button located in the
front panel of the DVR. While pressing and holding down the USB_BACKUP button, turn the power of
the DVR on. Kept holding the USB_BACKUP button for 5 seconds and then release it. After the release
of the USB_BACKUP button, restart the DVR using the power switch located one the rear of the DVR.
BUZZER SOUND
In the SYSTEM SETUP menu, select BUZZER SOUND. Press FORWARD /REVERSE button to
change the buzzer sound ON or OFF. Press MENU/ESC to return to SETUP MODE.
SYSTEM SETUP
◎ TIME/DATE SET [
]
◎ HDD FORMAT SET [
]
◎ AUTO SEQUENCE SET [
]
◎ FACTORY RESET [
]
◎ PLAY REPEAT: NO
◎ VIDEO SOURCE: PAL
◎ BUZZER SOUND: ON
◎ PASSWORD ENA: OFF
◎ NEW PASSWORD: 0000
------------------------------------------------------------ENTER SET ↑↓← → EXIT
PASSWORD ENA
In the SYSTEM SETUP menu, select PASSWORD ENA to enable or disable the DVR password
protection. Press the FORWARD/REVERSE button accordingly will turn ON/OFF the password
protection feature. When the password it set ON, the DVR will request for password whenever
the MENU button are pressed or to stop recording.
The factory default password is 0000. Press MENU/ESC to return to SETUP MODE menu or
simply browse up and down by pressing the UP/DOWN arrow keys.
SYSTEM SETUP
◎ TIME/DATE SET [
◎ HDD FORMAT SET [
]
]
◎ AUTO SEQUENCE SET [
]
◎ FACTORY RESET [
]
◎ PLAY REPEAT: NO
◎ VIDEO SOURCE: PAL
◎ BUZZER SOUND: ON
◎ PASSWORD ENA: OFF
◎ NEW PASSWORD: 0000
------------------------------------------------------------ENTER SET ↑↓← → EXIT
On Screen Display Functions
17
NEW PASSWORD
In the SYSTEM SETUP menu, select NEW PASSWORD. Use the directional buttons FORWARD/
REVERSE to change value of the password. Use the Up/Down buttons to toggle between the first
and the fourth digit setting. After changing from the manufacture default password, please
remember the newly created password or jot them down and place it in a secure area.
SYSTEM SETUP
◎ TIME/DATE SET [
]
◎ HDD FORMAT SET [
]
◎ AUTO SEQUENCE SET [
]
◎ FACTORY RESET [
]
◎ PLAY REPEAT: NO
◎ VIDEO SOURCE: PAL
◎ BUZZER SOUND: ON
◎ PASSWORD ENA: OFF
◎ NEW PASSWORD: 0000
------------------------------------------------------------ENTER SET ↑↓← → EXIT
VIDEO SET
Press the MENU button to enter SETUP MODE. Select VIDEO SET from the list, and press ENTER to
access the video setting pages as shown below.
SETUP MODE
◎ SYSTEM SET [
◎ VIDEO SET [
VIDEO SETUP
]
◎ NAME SETUP [
]
◎ BRI / CON SET [
]
◎ BOUNDARY: WHITE
◎ BACKGROUND: BLUE
◎ LANGUAGE: English
]
◎ RECORD SET [
◎ NETWORK SET [
]
◎ SENSOR SET [
]
◎ BACKUP SET [
]
]
------------------------------------------------------------ENTER SET ↑↓← → EXIT
]
◎ SCHEDULE SET [
------------------------------------------------------------ENTER SET ↑↓← → EXIT
NAME SETUP
In the VIDEO SETUP menu, select NAME SETUP and press ENTER. Press the UP/DOWN buttons
to select one of the 4 channels, and then press ENTER to rename. Use the FORWARD/REVERSE
buttons to change the alphabet letter charactors. There is a maximum of 8 letters/numbers entries per
channel. Press the ENTER/OK after completion or browse down to display by pressing the UP/
DOWN buttons and FORWARD/REVERSE to switch between name display ON/OFF.
When finished, press MENU/ESC to return to VIDEO SETUP menu.
NAME SETUP
-
CH1: C A M 1 _ _ _ _
CH2: C A M 2 _ _ _ _
CH3: C A M 3 _ _ _ _
CH4: C A M 4 _ _ _ _
DISPLAY: ON
On Screen Display Functions
18
BRI/CON SETUP
In the VIDEO SETUP menu, select BRI/CON SETUP and press ENTER. Press UP/DOWN to select
one of the four camera BRI/CON and press FORWARD/REVERSE buttons to adjust the value. Press
MENU to return to the VIDEO SETUP menu page. The default value is the middle for both the BRI/CON.
BRIGHT/CONTRAST SETUP
BRI: [
CON: [
II
II
]
BRI: [
CON: [
]
II
II
]
]
CAM2
CAM4
CAM1
CAM3
II
]
BRI: [
II
]
BRI: [
CON: [
II
]
CON: [
II
]
------------------------------------------------------------------ENTER SET ↑↓← → EXIT
BOUNDARY
In the VIDEO SETUP menu, select BOUNDARY. Use the FORWARD/REVERSE buttons to
select between White or Black boundary. Press MENU/ESC to return to the SETUP MODE
menu or press the UP/DOWN buttons to browse VIDEO SEPUT. Press the down button to advance
to BACKGROUND selection.
VIDEO SETUP
◎ NAME SETUP [
]
◎ BRI / CON SET [
]
◎ BOUNDARY: WHITE
◎ BACKGROUND: BLUE
◎ LANGUAGE: ENGLISH
------------------------------------------------------------ENTER SET ↑↓← → EXIT
18
BACKGROUND
In the VIDEO SETUP menu, select BACKGROUND. Use the directional buttons FORWARD/REVERSE
to select between black, blue, gray or white background. Press MENU/ESC to return to the SETUP
MODE or press the down button to advance the LANGUAGE selection.
VIDEO SETUP
◎ NAME SETUP [
]
◎ BRI / CON SET [
]
◎ BOUNDARY: WHITE
◎ BACKGROUND: BLUE
◎ LANGUAGE: ENGLISH
------------------------------------------------------------ENTER SET ↑↓← → EXIT
LANGUAGE: the DVR support ENGLISH only.
On Screen Display Functions
19
VIDEO SETUP
◎ NAME SETUP [
]
◎ BRI / CON SET [
]
◎ BOUNDARY: WHITE
◎ BACKGROUND: BLUE
◎ LANGUAGE: ENGLISH
------------------------------------------------------------ENTER SET ↑↓← → EXIT
RECORD SET
Press the MENU button to enter the SETUP MODE. Browse to select RECORD SET and press
ENTER to enter record setup as illustrated below.
SETUP MODE
◎ SYSTEM SET [
◎ VIDEO SET [
]
]
◎ RECORD SET [
]
◎ NETWORK SET [
]
◎ SENSOR SET [
◎ FW UPDATE [
]
]
]
◎ SCHEDULE SET [
------------------------------------------------------------ENTER SET ↑↓← → EXIT
RECORD SETUP
◎ OVERWRITE: YES
◎ REC SPEED: 50 Fld/1sec
◎ REC QUALITY: HIGH
◎ RESOLUTION: 720X240,360X240
◎ PB SPEED: 50 Fld/1sec
◎ AUDIO ENABLE: CAM1
◎ Alarm-R-SPD: 60Fld/1Sec
------------------------------------------------------------ENTER SET ↑↓← → EXIT
Press UP/DOWN to browse and press FORWARD/REVERSE to change the value setting.
OVERWRITE: YES, NO (YES: once HD is ful system will overwrite the oldest data that existed.)
REC SPEED: 60, 30, 20, 12 5, 3, 2, 1 Fld/1Sec, 1Fld/2Sec
REC QUALITY: VERY HIGH, HIGH, LOW, VERY LOW
RESOLUTION: 720x240, 360 X 240
PB SPEED: 60 Fld/1Sec, 30, 20, 12, 5, 3, 2, 1 Fld/2Sec, No use
AUDIO ENABLE: CAM1, CAM2, CAM3, CAM4, OFF (only 1 audio channel can be active)
Alarm-R-SPD: 50, 25, 12, 10, 5, 3, 2, 1 Fld/1Sec, 1Fld/2sec (Frame-by-Frame PB set to 1Fld/1Sec)
Press MENU to return to the SETUP MODE menu.
NETWORK SET
Press the MENU button to enter the SETUP MODE, select NETWORK SET and press ENTER to
enter network setup as illustrated below.
SETUP MODE
NETWORK SETUP
◎ SYSTEM SET [
◎ VIDEO SET [
]
]
◎ RECORD SET [
]
◎ NETWORK SET [
]
◎ SENSOR SET [
]
◎ BACKUP SET [
]
]
◎ SCHEDULE SET [
------------------------------------------------------------ENTER SET ↑↓← → EXIT
SUB NET: 255 255 255 000
GATEWAY: 010 192 001 001
IP ADDR: 010 192 001 001
NETWORK STATE: LOCAL_LAN/EXTER_LAN
NET CMD PORT: 5001
NET AV PORT: 5000
------------------------------------------------------------ENTER SET ↑↓← → EXIT
On Screen Display Functions
20
The DVR support static IP address only, it will NOTsupport dynamic IP address. With a valid static IP
address, please input them into each of the categories: SUB NET, GATEWAY, IP ADDR. If you are unsure,
please contact your ISP (Internet Service Provider) for detail as to what type of IP you signed up for when
registered. The NET CMD PORT and NET AV PORT are ports used to identity the DVR hardware. These
ports are required to be set open from the Router/Firewall in order for both audio and video to transmit
through the Router/Firewall to the internet. If you are not sure how to open ports 5000~5001 from the
Router/Firewall please consult with your local ISP or router manufacturer as to how to open up these ports.
To access the DVR from a remote location the same ports stated above is requried to be open from Router.
NOTE: When installing the client software in the remote computer and there are Router/Firewall, the
same ports 5000~5001 has to be opened from within the Router/Firewall in order for the audio/video to
breach though the Router/Firewall to the DVR.
SENSOR SET
Press the MENU button to enter the SETUP MODE, select SENSOR SET and press ENTER.
SETUP MODE
◎ SYSTEM SET [
◎ VIDEO SET [
]
]
◎ RECORD SET [
]
]
◎ NETWORK SET [
◎ SENSOR SET [
◎FW UPDATE [
]
]
◎ SCHEDULE SET [
]
------------------------------------------------------------ENTER SET ↑↓← → EXIT
SENSOR SETUP
◎ CHANNEL SELECT: CAM1
◎ SENSOR ENABLE: OFF
◎ MOTION ENABLE: OFF
◎ MOTION LEVEL: VERY HIGH
◎ COMPARE FRAME: 03
◎ EVENT REC TIME: OFF
◎ ALARM OUTPUT: NO USE
◎ AREA SET [
]
------------------------------------------------------------ENTER SET ↑↓← → EXIT
Press the directional buttons UP/DOWN to browse and press FORWARD/ REVERSE buttons to
change the value.
CHANNEL SELECT: CAM1, CAM2, CAM3, CAM4 (each CAM set has independent sensor setup)
SENSOR ENABLE: OFF, N.C., N.O.(normally closed and normally opened relay)
MOTION ENABLE: ON, OFF (enable/disable video motion detection)
MOTION LEVEL: VERY HIGH, HIGH, NORMAL, LOW, VERY LOW (the higher the picture qualit the
more HD space used)
On Screen Display Functions
21
COMPARE FRAME: 1~15(compare the changes of fields’ image for alarm trigger. 1=most sensitive
15=least sensitive)
EVENT REC TIME: OFF, 1~99 MINS, CONTINUES
ALARM OUTPUT: NO USE, 1~99 SEC, Always on (used for both sensor output and buzzer sound
output)
NOTE: To complete buzzer sound output settings; BUZZER SOUND located in the system Setup
needs to be turn ON to activate alarm buzzer sound.
Always on: alarm output set to Always on will enable both the sensor and buzzer output to
trigger. At anytime during alarm trigger; press the Menu (by remote control) to disable the buzzer
sound and go to ALARM output in the SENSOR SETUP to disable the sensor output.
AREA SET: Press Up/Down to browse and press [ENTER] to select the motion sensative area.
There are 48 blocks each are label ‘M’ stands form motion area. Use the directional buttons to choose
the area and press ENTER to confirm the selection or ENTER again again to de-select the fields.
M M M M M M M M
M M M M M M M M
M M M M M M M M
M M M M M M M M
M M M M M M M M
M M M M M M M M
NOTE: when “M” is yellow, it means that the blocks are selected or active areas. The “M” is white,
when the areas are de-selected or not active.
Press MENU/ESC to return to the SENSOR SETUP MODE.
Firmware Update
Press the MENU button to enter the SETUP MODE, select FW UPDATE and press ENTER. The
“CONTINUE USB FIRMWARE UPDATE?” will appear in red color and the USB total size and useful
size will be calculated from the flash drive. Press ENTER again to continue with the firmware update.
After the Enter is pressed, wait for approximately 20~30 seconds before the “updating FW %” start in
yellow highlights. Once the update reached 100%, the FW is successfully updated; restart the DVR.
On Screen Display Functions
USB FW UPDATE
SETUP MODE
◎ SYSTEM SET [
◎ VIDEO SET [
]
USB total size: 512 MByte
Useful size: 512 MByte
USB Firmware Update
]
◎ RECORD SET [
]
◎ NETWORK SET [
]
◎ SENSOR SET [
◎ FW UPDATE [
22
]
CONTINUE USB FIRMWARE UPDATE ?
]
◎ SCHEDULE SET [
]
Note: Only update firmware upon manufacturer’s request.
SCHEDULE SET
Press MENU button to enter the SETUP MODE, select SCHEDULE SET and press ENTER. Press
UP/DOWN to browse and press ENTER to high light selection and then the UP/DOWN buttons to turn
ON/OFF the schedule day(s). Use the FORWARD/REVERSE buttons to browse within the day setting
and use the UP/DOWN to change the start-stop schedule time value. Finally press ENTER to save and
proceed to the next day.
SETUP MODE
◎ SYSTEM SET [
◎ VIDEO SET [
]
]
◎ RECORD SET [
]
◎ NETWORK SET [
◎ SENSOR SET [
◎FW UPDATE [
]
]
]
◎ SCHEDULE SET [
]
------------------------------------------------------------ENTER SET ↑↓← → EXIT
SCHEDULE SETUP
START STOP
◎ MON OFF
__:__~__:__
__:__~__:__
◎ TUE OFF
◎ WED OFF
__:__~__:__
__:__~__:__
◎ THU OFF
__:__~__:__
◎ FRI OFF
◎ SAT OFF
__:__~__:__
◎ SUN OFF _ _ : _ _ ~ _ _ : _ _
◎ SCHEDULE ENABLE: OFF
------------------------------------------------------------ENTER SET ↑↓← → EXIT
To activate the scheduled recording; browse down to the SCHEDULE ENABLE and turn it to ON, then
press the Menu button or ESC button to exit out of the SCHEDULE SETUP menu.
Schedule recording: if schedule time is set within the DVR actual time interval, the DVR will show
*SCHEDULE MODE* but it will not start to record until approax.45 seconds later and then the stop
time end the DVR will stop to record according to the schedule time set. For example: if schedule start
to record at 11:30 and stop to record at 11:35, the DVR will start the scheduled record time of exactly
11:30 and will stop record at 11:35:59.
NOTE: if the DVR actual time is before the start scheduled time, the DVR need approax.45 seconds
to start to record. When schedule record is in use or in active mode, manual record and alarm/motion
record will NOT be active or cannot be used, to turn off *Schedule Mode *, go to SCHEDULE SET from
the SETUP MODE.
Network Viewer software
To Install Network Netviewer Software:
23
Insert Netviewer CD into the CD-ROM tray, an install shield wizard will appear as shown below. If
the install wizard fail to appear, please bowse the CD contents and double click on “setup.exe”
file to exceute and run setup. Select a desire language, and then click “Next” to proceed.
Press “Next” to continue the installation.
To install a different folder, click Browse and select another folder. Then click “Next” to continue
installation.
Network Viewer software
24
Setup will add program icons to the program folder listed below. Click “Next” to continue installation.
Click “Next” to install NetViewer software.
Network Viewer software
25
Setup complete, Click “Finish”.
Network Viewer software
To Uninstall Netviewer:
26
Go to start >programs/all programs> network viewer >uninstall Network Viewer or go to the system
control panel>Add or Remove programs to remove Network Viewer. The following windows will appear:
Click “Yes ” to proceed.
Click “OK ” to complete uninstallation.
Network Viewer software
27
How to Use Network Viewer client software:
To execute the Netviewer software go to start >all programs >Network Viewer > NetViewer4ch or
double click on Netviewer4CH shortcut icon located on the desktop and a Network Viewer window will
appear as shown below:
Click the
Setting icon on the Netviewer main screen, and the setting display box will appear.
Input an IP address assigned to the local DVR. Double check the AV Port and the Command Port to
match the local DVR’s port settings. The video size defaults to half size which has a resolution of 320x240,
for 720x240 select full size options.
Video Source: Please refer to country NTSC listing before changing.
Frame/Sec: To change the frame rate per second when connecter is establish. Enable One Channel
Transfer is recommended to transfer single image for better bandwidth control.
Local Rec. Path is to change the recording location to other hard drive or to other network drive.
AV code: this is auto- selected by the Net Viewer software, please do not change codec setting.
"OK" to confirm and exit.
Network Viewer software
28
Click the
Connect button, and the Logon dialog box will appear. The DVR IP address will
appear in the System field or click down arrow for options. Next input the DVR Password and click
“OK” to connect.
When successfully connected click OK.
The live video display should start to stream. In any case if the video is not streaming simply click on
the “PLAY FROM NETWORK” icon located in the upper right hand corner to start live view streaming
as illustrated below. Press the Disconn. disconnect button at any time to stop the live video streaming.
Network Viewer software
29
LIVE VIEW
Click on the Rec Start button to start recording on the local DVR from Network Viewer software and
the red LED light will light up (lower-Right hand corner). Click on the Rec Stop button to stop the DVR
recording and the red DVR LED light will gray out.
Note: If the local DVR is initially in record mode, then using the Netviewer to remotely connect to the
DVR, the Rec Stop button will not be active or unusable unless the Rec Start. is initiated first then the
Rec Stop can be used to stop the local DVR recording remotely. The initial record mode from the local
DVR has the priority over Netviewer software.
To save video file as AVI format: Click on the “Save As AVI…” button located in the upper-right hand
corner of Network Viewer software, a window will appear as illustrated below.
In the save to AVI window, select a save to location and give it a file name. Next select any
combination of channels ranging from 1-4 to save and click OK to proceed. A blue LED located in the
Lower-Right hand corner will appear. To stop AVI recording simply press on the “Save As AVI…” again.
Please note, AVI playbacks require window media and the playback speed will be 3 to 4 times faster
than the actual speed of the original recording. The Netviewer software cannot be used to playback
AVI files.
To save video streaming to local hard drive: Click on the "Save Video Stream to PC's HDD" to start to
save the video to local hard drive. A green LED located at the Lower-Right hand corner will appear. To
stop saving to local hard drive, simply press the “Save Video Stream to PC’s HDD” and the green light
will disappear and grayed out from the Lower-Right hand corner of Network Viewer.
Note: The “Save Video Stream to PC’s HDD” saves video format as .dvr which can only be playback
using the “File Play” tab from the Netviewer software. The .dvr video saved to location setting can be
change in the Netviewer setting under the “Local Rec Path”
Network Viewer software
30
In the save to AVI window, select a save to location and give it a file name. Next select any
combination of channels ranging from 1-4 to save and click OK to proceed. A blue LED located in the
Lower-Right hand corner will appear. To stop AVI recording simply press on the “Save As AVI…” again.
Please note, AVI playbacks require window media and the playback speed will be 3 to 4 times faster
than the actual speed of the original recording. The Netviewer software cannot be used to playback
AVI files.
To save video streaming to local hard drive: Click on the "Save Video Stream to PC's HDD" to start to
save the video to local hard drive. A green LED located at the Lower-Right hand corner will appear. To
stop saving to local hard drive, simply press the “Save Video Stream to PC’s HDD” and the green light
will disappear and grayed out from the Lower-Right hand corner of Network Viewer.
Note: The “Save Video Stream to PC’s HDD” saves video format as .dvr which can only be playback
using the “File Play” tab from the Netviewer software. The .dvr video saved to location setting can be
change in the Netviewer setting under the “Local Rec Path”
Network Viewer software
31
SCANDISK
Scandisk tab is used when the hard drive is removed from the inside of the DVR and connecting it
directly to the IDE bus of the computer or via 3rd party External enclosure. This procedure is affective
if there is something wrong with the DVR's ability to playback important recorded data. Please note
that this is not one of the remote features used to control the DVR remotely.
FILEPLAY
FilePlay tab is used to retrieve saved .dvr files from the local hard drive to playback. Click on the ”Open”
button to browse for .dvr files and simply click on the play button in blue and white to start playback.
Use pause, stop, REW, FF and adjust the playback speed accordingly.
Recording Time
32
Important Message:
The higher the video quality, the clearer the picture. On the contrary, the lower the video quality setting
can provide longer the record time. The record time varies depending on the field size and picture
quality. The following record time tables can be used as a reference. The record time capacity
can vary depending on the image complexity, color, black & white, brightness, contrast, image
movement and background video noise. The actual record time can be more or less than the
given reference tables. On average, it takes an additional 8K per second more with audio recording.
Recording time calculation formula:
A: Hard disk capacity,
B: Video Quality: Low (8Kb/frame), Normal (10Kb/frame), High (12Kb/frame)
C: Recording Frame Rate: 30fps, 15fps, 10fps, 7fps, 5fps, 4fps etc.
A GB x 1,000,000 k/GB)/ (BxC) k per sec. = D sec (Recording Time)D sec. / 60 / 60 / 24 = H days
(Recording Time)
For example, at NTSC 720 *240, Quality: Very High: 28Kb/s
Max. 30 fps or 60 field/sec on a 200GB HDD.
200GB x 1,000,000 k/GB)/ (28k/f x 60field/s) = 119047.62 Seconds.
119047.62/3600 = 33.07 Hours of record time for a 200GB hard drive
Recording size per field without Audio
Recording Size per Field
Resolution/Quality Very High
Unit : KB
High
Low
Very Low
PAL
720*240
33
24
19
18
360*240
16
12
10
9
NTSC
Very High
High
Low
Very Low
720*240
28
20
16
15
360*240
14
11
9
8
Recording Time
Recording Time Table:
Based on 200GB HDD at PAL
Field/Sec
100 50
25
Resolution
Very High
33.7 67.3
High
46.3 92.6
720*240
Low
58.5 117.0
Very Low
61.7 123.5
Very High 34.7
High
46.3
360*240
Low
55.6
Very Low 61.7
33
Unit : Hours
12
10
140.3
192.9
243.7
257.2
168.4
231.5
292.4
308.6
5
3
2
336.7 561.2 841.8 1683.5
463.0 771.6 1157.4 2314.8
584.8 974.7 1462.0 2924.0
617.3 1028.8 1543.2 3086.4
Recording Time Table
Based on 200GB HDD at NTSC
Field/Sec
120 60
30
20
12
5
3
2
Resolution
Very High
33.1 66.1 99.2 165.3 396.8 661.4 992.1
High
46.3 92.6 138.9 231.5 555.6 925.9 1388.9
720*240
Low
57.9 115.7 173.6 289.4 694.4 1157.4 1736.1
Very Low
61.7 123.5 185.2 308.6 740.7 1234.6 1851.9
Very High 33.1
High
42.1
360*240
Low
51.4
Very Low 57.9
Recording Time Table:
Based on 320GB HDD at PAL
Field/Sec
100 50
25
Resolution
Very High
53.9 107.7
High
74.1 148.1
720*240
Low
93.6 187.1
Very Low
98.8 197.5
Very High 55.6
High
74.1
360*240
Low
88.9
Very Low 98.8
1
1/2
3367.0
4629.6
5848.0
6172.8
Unit : Hours
1
1984.1
2777.8
3472.2
3703.7
1/2
3968.3
5555.6
6944.4
7407.4
Unit : Hours
12
10
224.5
308.6
389.9
411.5
269.4
370.4
467.8
493.8
5
3
2
1
538.7 897.9 1346.8 2693.6
740.7 1234.6 1851.9 3703.7
935.7 1559.5 2339.2 4678.4
987.7 1646.1 2469.1 4938.3
1/2
5387.2
7407.4
9356.7
9876.5
Recording Time
34
Recording Time Table
Unit : Hours
Based on 320GB HDD at NTSC
Field/Sec
Resolution
Very High
High
720*240
Low
Very Low
Very High
High
360*240
Low
Very Low
120
60
30
20
52.9
74.1
92.6
98.8
105.8
148.1
185.2
197.5
158.7
222.2
277.8
296.3
12
5
3
264.6 634.9 1058.2
370.4 888.9 1481.5
463.0 1111.1 1851.9
493.8 1185.2 1975.3
2
1
1/2
1587.3
2222.2
2777.8
2963.0
3174.6
4444.4
5555.6
5925.9
6349.2
8888.9
11111.1
11851.9
52.9
67.3
82.3
92.6
Recording Time Table:
Based on 500GB HDD at PAL
Field/Sec
100 50
25
Resolution
Very High
84.2 168.4
High
115.7 231.5
720*240
Low
146.2 292.4
Very Low
154.3 308.6
Very High 86.8
High
115.7
360*240
Low
138.9
Very Low 154.3
Recording Time Table
Based on 500GB HDD at NTSC
Field/Sec
120 60
30
Resolution
Very High
82.7 165.3
High
115.7 231.5
720*240
Low
144.7 289.4
Very Low
154.3 308.6
Very High 82.7
High
105.2
360*240
Low
128.6
Very Low 144.7
Unit : Hours
12
350.7
482.3
609.2
643.0
10
5
3
2
420.9 841.8 1402.9 2104.4
578.7 1157.4 1929.0 2893.5
731.0 1462.0 2436.6 3655.0
771.6 1543.2 2572.0 3858.0
1
1/2
4208.8
5787.0
7309.9
7716.0
8417.5
11574.1
14619.9
15432.1
Unit : Hours
20
248.0
347.2
434.0
463.0
12
5
3
2
413.4 992.1 1653.4 2480.2
578.7 1388.9 2314.8 3472.2
723.4 1736.1 2893.5 4340.3
771.6 1851.9 3086.4 4629.6
1
1/2
4960.3
6944.4
8680.6
9259.3
9920.6
13888.9
17361.1
18518.5
Version: 1.5F
47-3030-2006
www.securitymaninc.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising