Samsung SVP-5200P Specifications

PROJECTION TV RECEIVER

Chassis : J54A(P)C1.5

Model: SP42W4HPX/BWT

SP43T7HPX/SED

PROJECTION TV RECEIVER C O N T E N T S

1.

Precautions

2.

Reference Information

3.

Specifications

4.

Alignment and Adjustments

5.

Troubleshooting

6.

Exploded View and Parts List

7.

Electric Parts List

8.

Block Diagrams

9.

Wiring Diagram

10.

Schematic Diagrams

ELECTRONICS

© Samsung Electronics Co., Ltd. Feb. 2003

Printed in Korea

AA82-00418A

Precautions

1. Precautions

Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays.

1-1 Safety Precautions

1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields.

2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers.

3. Make sure that there are no cabinet openings through which people—particularly children—might insert fingers and contact dangerous voltages. Such openings include the spacing between the picture tube and the cabinet mask, excessively wide cabinet ventilation slots, and improperly fitted back covers.

If the measured resistance is less than 1.0

megohm or greater than 5.2 megohms, an abnormality exists that must be corrected before the unit is returned to the customer.

4. Leakage Current Hot Check (Figure 1-1):

Warning: Do not use an isolation transformer during this test. Use a leakagecurrent tester or a metering system that complies with American National Standards

Institute (ANIS C101.1, Leakage Current for

Appliances), and Underwriters Laboratories

(UL Publication UL1410, 59.7).

5. With the unit completely reassembled, plug the AC line cord directly into the power outlet. With the unit’s AC switch first in the

ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit, etc.) and all exposed metal parts, including: antennas, handle brackets, metal cabinets, screwheads and control shafts. The current measured should not exceed 0.5 milliamp. Reverse the powerplug prongs in the AC outlet and repeat the test.

DEVICE

UNDER

TEST

TEST ALL

EXPOSED METAL

SURFACES

2-WIRE CORD

ALSO TEST WITH

PLUG REVERSED

(USING AC ADAPTER

PLUG AS REQUIRED)

LEAKAGE

CURRENT

TESTER

(READING SHOULD

NOT BE ABOVE

0.5mA)

EARTH

GROUND

Fig. 1-1 AC Leakage Test

6. Antenna Cold Check:

With the unit’s AC plug disconnected from the

AC source, connect an electrical jumper across the two AC prongs. Connect one lead of the ohmmeter to an AC prong. Connect the other lead to the coaxial connector.

7. X-ray Limits:

The picture tube is especially designed to prohibit X-ray emissions. To ensure continued

X-ray protection, replace the picture tube only with one that is the same type as the original.

Carefully reinstall the picture tube shields and mounting hardware; these also provide X-ray protection.

8. High Voltage Limits:

High voltage must be measured each time servicing is done on the B+, horizontal deflection or high voltage circuits. Correct operation of the X-ray protection circuits must be reconfirmed whenever they are serviced.

(X-ray protection circuits also may be called

“horizontal disable” or “hold-down”.)

Heed the high voltage limits. These include the X–ray Protection Specifications Label, and the Product Safety and X-ray Warning Note on the service data schematic.

Samsung Electronics 1-1

Precautions

1-1 Safety Precautions (Continued)

9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components.

10. Design Alteration Warning:

Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard. Also, any design changes or additions will void the manufacturer’s warranty.

11. Hot Chassis Warning:

Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord. If an isolation transformer is not used, these units may be safely serviced only if the AC power plug is inserted so that the chassis is connected to the ground side of the

AC source.

To confirm that the AC power plug is inserted correctly, do the following: Using an AC voltmeter, measure the voltage between the chassis and a known earth ground. If the reading is greater than 1.0V, remove the AC power plug, reverse its polarity and reinsert.

Re-measure the voltage between the chassis and ground.

12. Some TV chassis are designed to operate with

85 volts AC between chassis and ground, regardless of the AC plug polarity. These units can be safely serviced only if an isolation transformer inserted between the receiver and the power source.

13. Some TV chassis have a secondary ground system in addition to the main chassis ground.

This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulating material that must not be defeated or altered.

14. Components, parts and wiring that appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards.

1-2

15. Observe the original lead dress, especially near the following areas: Antenna wiring, sharp edges, and especially the AC and high voltage power supplies. Always inspect for pinched, out-of-place, or frayed wiring. Do not change the spacing between components and the printed circuit board. Check the AC power cord for damage. Make sure that leads and components do not touch thermally hot parts.

16. Picture Tube Implosion Warning:

The picture tube in this receiver employs

“integral implosion” protection. To ensure continued implosion protection, make sure that the replacement picture tube is the same as the original.

17. Do not remove, install or handle the picture tube without first putting on shatterproof goggles equipped with side shields. Never handle the picture tube by its neck. Some

“in-line” picture tubes are equipped with a permanently attached deflection yoke; do not try to remove such “permanently attached” yokes from the picture tube.

18. Product Safety Notice:

Some electrical and mechanical parts have special safety-related characteristics which might not be obvious from visual inspection.

These safety features and the protection they give might be lost if the replacement component differs from the original—even if the replacement is rated for higher voltage, wattage, etc.

Components that are critical for safety are indicated in the circuit diagram by shading,

Use replacement components that have the same ratings, especially for flame resistance and dielectric strength specifications.

A replacement part that does not have the same safety characteristics as the original might create shock, fire or other hazards.

Samsung Electronics

Precautions

1-2 Servicing Precautions

Warning 1 : First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions.

Warning 2 : An electrolytic capacitor installed with the wrong polarity might explode.

1. Servicing precautions are printed on the cabinet. Follow them.

2. Always unplug the unit’s AC power cord from the AC power source before attempting to: (a)

Remove or reinstall any component or assembly, (b) Disconnect an electrical plug or connector, (c) Connect a test component in parallel with an electrolytic capacitor.

3. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such elements to their original position.

4. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that the portion around the serviced part has not been damaged.

5. Check the insulation between the blades of the

AC plug and accessible conductive parts

(examples: metal panels, input terminals and earphone jacks).

6. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON. Connect an insulation resistance meter (500V) to the blades of the AC plug.

The insulation resistance between each blade of the AC plug and accessible conductive parts

(see above) should be greater than 1 megohm.

7. Never defeat any of the B+ voltage interlocks.

Do not apply AC power to the unit (or any of its assemblies) unless all solid-state heat sinks are correctly installed.

8. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead; always remove the instrument’s ground lead last.

9. When some parts inside the optical engine

(except lamp) are damaged, replace the whole optical engine.


Precautions

1-3 Precautions for Electrostatically Sensitive Devices (ESDs)

1. Some semiconductor (“solid state”) devices are easily damaged by static electricity. Such components are called Electrostatically

Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity.

2. Immediately before handling any semicon ductor components or assemblies, drain the electrostatic charge from your body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. (Be sure to remove it prior to applying power— this is an electric shock precaution.)

3. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent accumulation of electrostatic charge.

4. Do not use freon-propelled chemicals. These can generate electrical charges that damage

ESDs.

5. Use only a grounded-tip soldering iron when soldering or unsoldering ESDs.

6. Use only an anti-static solder removal device.

Many solder removal devices are not rated as

“anti-static”; these can accumulate sufficient electrical charge to damage ESDs.

7. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive materials.

8. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.

9. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD.

1-4 Samsung Electronics

Reference Information

A

Ah

Å dB dBm kg kHz k Ω km

Hz h ips kWh

°C

°F

°K

F g

H

G

GHz km/h kV kVA kW

I

MHz

2. Reference Information

2-1 Tables of Abbreviations and Acronyms

Table 2-1 Abbreviations

Ampere

Ampere-hour

Angstrom

Decibel

Decibel Referenced to One

Milliwatt

Degree Celsius

Degree Fahrenheit degree Kelvin

Farad

Gauss

Gigahertz

Gram

Henry

Hertz

Hour

Inches Per Second

Kilowatt-hour

Kilogram

Kilohertz

Kilohm

Kilometer

Kilometer Per Hour

Kilovolt

Kilovolt-ampere

Kilowatt

Liter

Megahertz mH mI mm ms mV nF

Ω pF

µs

µW mA mg

µA

µF

µH

µm

MV

MW

M Ω m

V

VA

W

Wh

Ib rpm rps s

Megavolt

Megawatt

Megohm

Meter

Microampere

Microfarad

Microhenry

Micrometer

Microsecond

Microwatt

Milliampere

Milligram

Millihenry

Milliliter

Millimeter

Millisecond

Millivolt

Nanofarad

Ohm

Picofarad

Pound

Revolutions Per Minute

Revolutions Per Second

Second (Time)

Volt

Volt-ampere

Watt

Watt-hour



FBP

FBT

FF

FM

DVM

EIA

ESD

ESD

CATV

CB

CCD

CCTV

Ch

CRT

CW

DC

FS

GND

G-Y

H

HF

HI-FI

IC

IC

IF

ANSI

APC

APC

A/V

AVC

BAL

BPF

B-Y

ABL

AC

ACC

AF

AFC

AFT

AGC

AM

Table 2-2 Table of Acronyms

Automatic Brightness Limiter

Alternating Current

Automatic Chroma Control

Audio Frequency

Automatic Frequency Control

Automatic Fine Tuning

Automatic Gain Control

Amplitude Modulation

American National Standards Institute

Automatic Phase Control

Automatic Picture Control

Audio-Video

Automatic Volume Control

Balance

Bandpass Filter

Blue-Y

Community Antenna Television (Cable TV)

Citizens Band

Charge Coupled Device

Closed Circuit Television

Channel

Cathode Ray Tube

Continuous Wave

Direct Current

Digital Volt Meter

Electronics Industries Association

Electrostatic Discharge

Electrostatically Sensitive Device

Feedback Pulse

Flyback Transformer

Flip-Flop

Frequency Modulation

Fail Safe

Ground

Green-Y

High

High-Frequency

High Fidelity

Inductance-Capacitance

Integrated Circuit

Intermediate Frequency

SW

TP

TTL

TV

UHF

UL

UV

VCD

RC

RF

R-Y

SAP

SAW

SIF

SMPS

S/N

VCO

VCXO

VHF

VIF

VR

VTR

VTVM

TR

NEC

NTSC

OSD

PCB

PLL

PWM

QIF

R

I/O

L

L

LED

LF

MOSFET

MTS

NAB

Input/output

Left

Low

Light Emitting Diode

Low Frequency

Metal-Oxide-Semiconductor-Field-Effect-Tr

Multi-channel Television Sound

National Association of Broadcasters

National Electric Code

National Television Systems Committee

On Screen Display

Printed Circuit Board

Phase-Locked Loop

Pulse Width Modulation

Quadrature Intermediate Frequency

Right

Resistor & Capacitor

Radio Frequency

Red-Y

Second Audio Program

Surface Acoustic Wave(Filter)

Sound Intermediate Frequency

Switching Mode Power Supply

Signal/Noise

Switch

Test Point

Transistor Transistor Logic

Television

Ultra High Frequency

Underwriters Laboratories

Ultraviolet

Variable-Capacitance Diode

Voltage Controlled Oscillator

Voltage Controlled Crystal Oscillator

Very High Frequency

Video Intermediate Frequency

Variable Resistor

Video Tape Recorder

Vacuum Tube Voltmeter

Transistor



2-2 IC Line Up

No.

1

Block Name

2 SCALER MODULE

3

Samsung Electronics

MAIN

CG MODULE

Table 2 - 3 IC Line - Up

IC Location

IC02

IC17

IC06

IC01

IC13

IC05

IC07

C03

IC09, IC10, IC11,IC14

IC12

IC04, IC15, IC16

IC11

IC01A

IC04

IC08

IC602

IC13

IC06

IC05

IC702

IC605

IC704

IC705

IC703

IC802

IC101

IC701

IC Name

TEA5114A

7905

PCF8574

TEA6425D

TEA6425D

TEA6422D

PCF8591T

PCF8591T

MSP3411G-QA-B8V3/MSP3452G(Option)

74HC123

7027

LF18CDT

78RM33D

VSP9407B-B11

CXA2165Q

74HC4052

NC7SB3157P6X

24C64

EL2250CS

7042

78RM33D

TLC2932IPWLE

TSC87251G2D-OTP

SDC12

TL072C

KA324D

7S04

2-3


No.

4

5

Block Name

MICOM MODULE

SUB

Table 2 - 3 IC Line - Up (Continued)

IC Location

IC902

IC903

IC901

IC904

IC905

IC431, IC471

IC841

IC851

ICS801

IC402

ICZ03, ICZ04

IC831S

IC301

IC Name

24C16

78RM33D

SDA5550M

7025

M27W201-80F6

MC4558C

78R05

SE110N

VIPER12A

DDRI1001

STK392-010

STR-X6459A

LA7845


2-3 MICOM IIC BUS LINE -UP

/ MSP3452G(Option)



MENO


3. Specifications

Broadcasting System

Scanning System

Tuning Range

Antenna Impedance

Intermediate Frequency

Sound Output

Rated Voltage

High Voltage

FUSE

Power Consumption

CW : EURO Multi (PAL, SECAM-B/G, D/K, I, L/L)

CS : PAL Multi (PAL, SECAM-B/G, D/K, I, NT4, 43, NT3.58)

100Hz / Progressive

VHF : CH2 ~ CH12

UHF : CH21 ~ CH69

Cable : CHS1 ~ S40

75 ohm Unbalanced

System

B/G

D/K

I

L(L’)

Video(MHz)

38.90

38.90

38.90

34.5(41.0)

Sound(MHz)

33.40

32.40

32.90

41.0(34.5)

MAX : 15W x 2 ( 8ohm )

AC220V / Free Voltage ( Option )

29KV

250V/6.3A

CODE NO : 3601-000300

230W

Specifications


❏ White Balance (Southeast Asia)

Fixed

ITEM

HIGHT

LOW

R-CUT OFF

G-CUT OFF

B-CUT OFF

R-DRIVE

G-DRIVE

B-DRIVE

SUB-BRIGHT

SUB-CONTRAST

SUB COLOR

COL AXIS

42W5 x y Y

47W1 x y Y

43T6/43T7 x y Y

290 304 10.5

290 304 9.5

290 304 10

258 254 0.45

258 254 0.35

258 254 0.4

31

16

6

12

15

20

21

42

15

2

16

20

26

48

31

28

10

4

15

2

31

26

7

13

15

20

23

41

15

2

48T6 x y Y

290 304 9.5

258 254 0.4

7

6

31

21

17

20

32

54

15

2

42W5 x y Y

42W5 x y Y

290 304 8.5

290 304 6.5

258 254 0.35

258 254 0.35

31

25

8

11

16

20

29

46

15

2

31

15

9

11

12

20

35

41

15

2

❏ White Balance (Australia)

ITEM

HIGHT

LOW

R-CUT OFF

G-CUT OFF

B-CUT OFF

R-DRIVE

G-DRIVE

B-DRIVE

SUB-BRIGHT

SUB-CONTRAST

SUB COLOR

COL AXIS

42W5 x y Y

47W1 x y Y

43T6/43T7 x y Y

290 304 10.5

290 304 9.5

290 304 10

290 290 0.45

290 290 0.35

590 290 0.4

31

20

8

10

21

20

21

35

10

1

22

20

23

38

31

25

9

6

10

1

31

26

8

13

22

20

21

36

10

1

48T6 x y Y

290 304 9.5

290 290 0.4

5

8

31

24

22

20

25

45

10

1

42W5 x y Y

42W5 x y Y

290 304 8.5

290 304 6.5

290 290 0.35

290 290 0.35

31

29

7

10

22

20

22

41

10

1

31

17

15

11

19

20

23

32

10

1


Alignment and Adjustments

4. Alignment and Adjustments

4-1 When entering the service mode;

1. Turn on the TV, and then select “DYNAMIC” on the picture adjustment mode.

2. Turn off the TV(STAND-BY).

3. Enter the service mode by pressing the remote control keys in the following sequence:

Display -> Menu -> Mute -> Power ON

Note : If necessary, re-do steps 1~3.

Initial display when the service mode is switched.

4-1-1 WHEN A RF SIGNAL IS RECEIVED

CW MODEL

DEFLECTION

VIDEO ADJUST 1

VIDEO ADJUST 2

VIDEO ADJUST 3

VIDEO ADJUST 4

OPTION (87h 05ch)

YC DELAY

RESET

SIM-814EW YY.MM.DD

CS MODEL

DEFLECTION

VIDEO ADJUST 1

VIDEO ADJUST 2

VIDEO ADJUST 3

VIDEO ADJUST 4

OPTION (D8 O4 2E)

YC DELAY

RESET

T_CADEC_010 YY.MM.DD

4-1-2 SERVICE MODE CONTROL KEYS

MAIN MENU

UP / DOWN

RIGHT / LEFT

MENU DISPLAY

Select item by moving cursor

Decrease or increase the adjustment values

[Navigation Key]

✍

PRECAUTIONS

1. When EEPROM IC (IC902) is replaced, first connect the power cord and wait for about 4~5 seconds.

2. After replacing EEPROM IC (IC902), enter the Service mode. Next, enter the standard data or the previous EEPROM IC data before replacement. And then check and adjust any items related to

Geometric, Picture, Option.



4-2 FACTORY MODE MENU

4-2-1 CW MODEL(SIM-814EW)

4-2-1(A) DEFLECTION

Item

V Amp

V Shift

H EW

H Shift

V Linearity

Upper Linearity

Lower Linearity

V SC

H Parabolra

Upper Corner

Lower Corner

H Trapezium

Bow

Angle

V Position

Up UCG

Lo UCG

CXA Left Blk

CXA Right Blk

Range

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 3

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 15

0 ~ 15

0 ~ 15

0 ~ 15

0 ~ 3

0 ~ 63

0 ~ 63

Initial Data

31

31

0

29

36

34

21

31

0

50

25

0

0

7

39

32

41

24

7

Remark

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

Variable

FIX

Variable

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX


4-2-1(B) VIDEO ADJUST1

Item

R Cutoff

G Cutoff

B Cutoff

Color On/Off

CB Offset

CR Offset

R Drive

G Drive

B Drive

Sub Bright

Sub Contrast

Sub Color

Sut Tint

CTI Level

COL Axis

LTI Level

VSU

Melody Volume

LIT Mode

System

Range

0 ~ 63

0 ~ 63

0 ~ 15

0 ~ 23

0 ~ 63

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 1

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 15

0 ~ 20

0 ~ 3

0 ~ 3

Initial Data

1

1

3

31

1

25

15

8

1

1

2

4

1

31

31

25

25

25

25

25


Remark

Variable

FIX

Variable

Variable

Variable

Variable

Variable

FIX

Variable

Variable

Variable

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX



4-2-1(C) VIDEO ADJUST2

Item

ABL Level

Gamma

DPIC Level

DC Trans

ABL TH

VM Level

VM Corint

VM f0

VM Limit

VM Delay

SHP CD

SHP f0

SHP f1 & P/O

AKB Time

BandPass 9407

HighPass 9407

S ABL

P ABL

Range

0 ~ 3

0 ~ 3

0 ~ 3

0 / 1

-

0 ~ 63

-

-

0 ~ 3

0 ~ 15

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 15

0 ~ 3

0 ~ 15

0 ~ 3

Initial Data

1

11

13

24

40

0

15

1

1

0

1

0

1

15

1

3

1

2

Remark

FIX

FIX

FIX

-

FIX

FIX

FIX

FIX

FIX

-

-

FIX

FIX

FIX

FIX

-

FIX

FIX


4-2-1(D) VIDEO ADJUST3

Item

H Comp

V Comp

Pin Comp

AFC Comp

H-Sync Phase

NR Off Value

CG HAO

CG VAO

NR High Ref

NR Low Ref

NR High Value

NR Low Value

NR Hight Ref(S)

NR Low Ref(s)

NR High Value(S)

NR Low Value(S)

NR Read M/S

Range

0 ~127

0 ~127

0 ~255

0 ~255

0 ~127

0 ~127

0 ~255

0 ~255

0/27

0 ~ 15

0 ~ 15

0 ~ 7

0 ~ 7

0 / 1

0 ~ 9

0 ~ 20

0 ~ 20

Initial Data

51

20

0

17

40

3

17

51

0 0

6

10

0

0

15

1

4

3


Remark

FIX



4-2-1(E) VIDEO ADJUST4

Item

SECAM Color Main

SECAM Color Pip

Picture Limit

OSD Contrast

TTX Contrast

Range

0 ~255

0 ~255

0 ~ 3

0 ~ 15

0 ~ 15

4-2-1(F) OPTION

Item

SYSTEM

SOUND

ASPECT

WIDE 4:3

X-RAY

AUTO FM

PIP

LNA

Letter Box

D/W PIP

AGC

Natural Zoom

HELP

Initial Data

28

28

3

10

3

Setting Data

CS/CW

A2-NICAM/Virtual Dolby

WIDE / 4:3

OFF / ON

OFF / ON

OFF / ON

OFF / 2-TUNER

OFF / ON

OFF / ON

OFF / ON

OFF / ON

OFF / ON

OFF / ON

Appliance

OFF

ON

ON

On

ON

OFF

CW

Virtual Dolby

WIDE on

ON

ON

2-TUNER

Remark

FIX

Remark


4-2-1(G) YC DELAY

Item

P.YC(AV) Delay

S.YC(AV) Delay

N.YC(AV) Delay

P.BG.YC Dealy

P.DK.YC Delay

P.I.YC Delay

P.M.YC Delay

P.N.YC Delay

S.BG.YC Delay

S.DK.YC Delay

S.I.YC Delay

S.M.YC Delay

S.L.YC Delay

N.M.YC Delay

N4.43 YC Delay

Range

-7

-10

3

-6

-7

-9

-9

0

0

1

-2

0

1

-5

1




4-2-2 CS MODEL(T_CADEC_010)

4-2-2(A) DEFLECTION

Item

V Amp

V Shift

H EW

H Shift

V Linearity

Upper Linearity

Lower Linearity

V SC

H Parabolra

Upper Corner

Lower Corner

H Trapezium

Bow

Angle

V Position

Up UCG

Lo UCG

CXA Left Blk

CXA Right Blk

Initial Data

Range

0

50

25

31

31

31

0

15

33

33

18

0

2

7

0

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 3

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 15

0 ~ 15

0 ~ 15

0 ~ 15

0 ~ 3

0 ~ 63

0 ~ 63

42W5 47W1 43T6/43T7 48T6 54T6 62T6

NTSC PAL NTSC PAL NTSC PAL NTSC PAL NTSC PAL NTSC PAL

48

31

48

24

48

31

48

24

48

31

48

24

48

31

48

24

48

31

48

24

48

31

48

24

48

31

48

24

48

31

48

24

48

31

48

24

48

31

48

24

48

31

48

24

48

31

48

24

7

0

0

2

15

33

33

18

31

31

31

0

0

50

25

7

0

0

2

15

33

33

18

31

31

31

0

0

50

25

7

0

0

2

15

33

33

18

31

31

31

0

0

50

25

0

50

25

31

31

31

0

15

33

33

18

0

2

7

0

0

50

25

31

31

31

0

15

33

33

18

0

2

7

0

Remark

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

Variable

FIX

Variable

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX


4-2-2(B) VIDEO ADJUST1

Item

R Cutoff

G Cutoff

B Cutoff

Color On/Off

CB Offset

CR Offset

R Drive

G Drive

B Drive

Sub Bright

Sub Contrast

Sub Color

Sut Tint

CTI Level

COL Axis

LTI Level

VSU

Melody Volume

LIT Mode

System

Range

0 ~ 63

0 ~ 63

0 ~ 15

0 ~ 23

0 ~ 63

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 1

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 63

0 ~ 15

0 ~ 20

0 ~ 3

0 ~ 3

Initial Data

1

2

3

31

1

25

15

8

1

1

2

4

1

31

31

25

25

25

25

25


Remark

Variable

Variable

Variable

Variable

Variable

Variable

Variable

Variable

Variable

Variable

Variable

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX



4-2-2(C) VIDEO ADJUST2

Item

ABL Level

Gamma

DPIC Level

DC Trans

ABL TH

VM Level

VM Corint

VM f0

VM Limit

VM Delay

SHP CD

SHP f0

SHP f1 & P/O

AKB Time

BandPass 9407

HighPass 9407

S ABL

P ABL

Range

0 ~ 3

0 ~ 3

0 ~ 3

0 / 1

-

0 ~ 63

-

-

0 ~ 3

0 ~ 15

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 3

0 ~ 15

0 ~ 3

0 ~ 15

0 ~ 3

Initial Data

1

11

13

24

40

0

15

1

1

0

1

0

1

15

1

3

1

2

Remark

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX

FIX


4-2-2(D) VIDEO ADJUST3

Item

H Comp

V Comp

Pin Comp

AFC Comp

H-Sync Phase

NR Off Value

CG HAO

CG VAO

NR High Ref

NR Low Ref

NR High Value

NR Low Value

NR Hight Ref(S)

NR Low Ref(s)

NR High Value(S)

NR Low Value(S)

NR Read M/S

Range

0 ~127

0 ~127

-

-

0 ~127

0 ~127

-

-

-

0 ~ 15

0 ~ 15

0 ~ 7

0 ~ 7

0 / 1

-

0 ~ 20

0 ~ 20

Initial Data

51

20

0

17

40

3

17

51

0 0

6

10

0

0

15

1

4

3


Remark

FIX



4-2-1(E) VIDEO ADJUST4

LANGUAGE

SOUNG

CRT

CHANNEL

X-LAY

TTX

AUTO FM

PIP

MULTI PIP

LNA

HIGH DEV

SCART

LETTER BOX

DW PIP

LIST PRIOR

Item

SECAM Color Main

SECAM Color Pip

Picture Limit

OSD Contrast

TTX Contrast

4-2-1(F) OPTION

Item

TTX LANG

AGC

AV MEMORY

AUSTRALIA

Range

0 ~255

0 ~255

0 ~ 3

0 ~ 15

0 ~ 15

Initial Data

28

28

3

10

3

Setting Data

ENG+THAI / ENG+CHINA

ENG+MIDDLE / ONLY ENG

A2-NICAM/Virtual Dolby

WIDE / 4:3

100-channel / 200-channel

/250-chanel

OFF / ON

OFF / ON

OFF / ON

OFF / 2-TUNER

OFF / ON

OFF / ON

OFF / ON

RCA+1SCART+DVD / RCA+DVD

OFF / ON

OFF / ON

OFF / ON

WEST EUROPE / EAST EUROPE

RUSSIAN / GREEK-TURKEY

ARABIC / FARSI / AREB-HEBREW

OFF / ON

OFF / ON

OFF / ON

Appliance

(Southeast Asia)

ONLY ENG

ENG+THAI(Thailand)

Virtual Dolby

4:3(Option)

100-channel

ON

ON

ON

2-TUNER

ON

ON

OFF

RCA+1SCART+DVD

ON

OFF

OFF

0N(AUSTRALIA)

WEST EUROPE

OFF

OFF

OFF

4-12

WEST EUROPE

OFF

OFF

OFF

Appliance

(CHINA)

ENG+CHINA

Virtual Dolby

4:3(Option)

200-channle

ON

OFF

ON

2-TUNER

ON

ON

OFF

RCA+DVD

ON

OFF

OFF

Remark

FIX

Appliance

(Middle East)

ENG+MIDDLE

Virtual Dolby

4:3(Option)

250-channle

ON

ON

ON

2-TUNER

ON

ON

OFF

RCA+1SCART+DVD

ON

OFF

OFF

ARABIC

OFF

OFF

OFF

Samsung Electronics

4-2-2(G) YC DELAY

Item

P.YC(AV) Delay

S.YC(AV) Delay

N.YC(AV) Delay

P.BG.YC Dealy

P.DK.YC Delay

P.I.YC Delay

P.M.YC Delay

P.N.YC Delay

S.BG.YC Delay

S.DK.YC Delay

S.I.YC Delay

S.M.YC Delay

S.L.YC Delay

N.M.YC Delay

Range

-9

-7

-10

3

0

-7

-9

-2

0

1

1

0

1

-5




4-3 Screen Change (When Adjusting I 2 C Bus Geometric Items)

1 V AMP 6 V - S - CORRECTION

2 V SHIFT

3 H EW

7 H Parabolra

8 H Trapezium

4 H SHIFT

5 V LINEARITY

9 BOW

10 ANGLE



4-4 Other Adjustments

4-4-1 Screen Adjustment

1. Warm up the TV for at least 30 minutes.

3. Trun to the Video Mode(No Signal) using a remote-control.

4. Connect an oscilloscope to RK, GK, BK.

5. Adjust the VR (VR501, VR531, VR561) screen so that RK, GK, BK pulse is 20Vp-p each.

(Turn the R,G,B VR screen fully counterclockwise in the area of each flyback line.)

4-4-2 White Balance Adjustment keys in the following sequence :

Displsy → Menu → Mute → Power ON

3. Select Sub-Bright by pressing the Volume +/keys.

4. Adjust so that the 63 step on the right side of the screen is not seen (Use the Volume +/keys).

5. Press the Menu key to exit.

4-4-4 High Voltage (30KV) Check

PRECAUTION

1. Input a lion head pattern.

2. Input 100% white pattern.

3. In the stand-by mode, press the remote-control keys in the following sequence:

Displsy

→ Menu → Mute → Power ON


5. Input a 10-step signal.

6. R-cut off, B-cut off, and G-cut off by pressing the Volume +/- keys.

7. Adjust the low light with viewing the dark side of the screen.

8. Select R-drive, G-drive and B-drive by pressing the Volume +/- keys.

9. Adjust the high light with viewing the light side of the screen.

10. If necessary, redo adjustments 6~9.

11. Press the Menu key to exit.

4-6-3 Sub-Brightness Adjustment

1. Input a sub-brightness adjustment signal.

(TOSHIBA PATTERN)

2. In the stand-by mode, press the remote-control


4. Use a digital multimeter.

ADJUSTMENT

1. Connect the (+) terminal of the digital multimeter to Q471 and the (-) terminal to

Q401 (located on the deflection board).

2. Adjust RR471S (located on the sub board) so that the digital meter indicates

DC290V ± 0.1V.

4-4-5 F.S. (Fail Safe) Circuit Check

(GT430,GT431)

Note : The F.S. Circuit check must be performed after servicing.

1. Turn on the TV.

3. Short F/S Test point (located on the SUB PCB).

Then, both sound and picture disappear.

(Note: Even if the shorted terminals are removed, both sound and picture do not appear. This proves the F.S.

circuit is working. )

4. To restore both sound and picture, turn off the

TV and reset it after about 30 seconds.



4-4-6 Static Focus Adjustment

PRECAUTION

2. Input a crosshatch pattern.

3. Cover the lenses that are not being adjusted.

4. Connect a convergence jig and read data.

5. Adjust the lens for best focus.

(See Fig, 4-1)

STATIC FOCUS (CONTINUED)

Vary the focus pack VR (Red, Blue) on the front cabinet. Adjust the TV for best possible focus around the center of the crosshatch pattern, without losing overall screen balance.

Figure Crosshatch Pattern

Examine these points together.

4. When the lens is turned clockwise, the color aberration will change as follows:

Lens Color Aberration Change

R Orange - Crimson

G Blue - Red

B Purple - Green

5. Green lens adjustment:

Set the lens at the point where Blue just changes to Red. If the color aberration is irregular throughout the picture screen, adjust the lens to show Red color aberration

(approximately 1~3 mm area) within a 3-block grid around the horizontal center-line. If the color aberration is irregular, adjust the lens as shown in the diagram below. (Accurate alignment of Green is important for overall color quality.)

Set the Red lens at the point where Orange becomes Crimson.

7. Blue lens adjustment

Set the Blue lens at the point where Purple becomes Green.

P

L1 L2

Examine these points together

Fig. 4-1 Crosshatch Pattern.

4-4-7 Lens Focus Adjustment

PRECAUTIONS

1. Do this adjustment after the static focus adjustment and the tilt adjustment.

(Contrast:100, Brightness:50)

3. Input a crosshatch pattern.

ADJUSTMENT

1. Loosen the lens screws.

2. Cover the two lenses that are not being adjusted.

3. Adjust the lens, observing the color aberration vertically and horizontally within 3 blocks of the center of the crosshatch pattern.

4-16

RED ABERRATION BLUE ABERRATION

L1, L2 < P

Fig. 4-2 Color Aberration

Samsung Electronics


4-5 Beam alignment Adjustments

1. Select the “DYNAMIC” video mode.

2. Warm up the set at least for 10 minutes.

3. Enter the Convergence mode by pressing the remote control buttons in the following sequence :

Mute

4. Set the Beam Alignment Adjustment CY to Zero magnetic field area.

(Creation of CPM Zero Magnet) (Creation of the 2-pole/4-pole zero magnets)

5. Check the squarewave at the point where the focus is misaligned.

6. Press the button on the remote control during 3~5 sec and vibrating dot-pattern appears.

7. Adjust the Focus-pack VR for defocusing.

8. Mute the other patterns (R/B) other than G-PATTERN.

G-FOCUS CORE

G-FOCUS

(Varying G-Focus Pack)

CORE

Varying the 2-pole of VM

(Positioning the Core in the Center)

(When VM 2-Pole Adjustment is completed)

Varying the 4-pole of VM

(Adjust until the light around the core becomes a circle)

9. Adjust the 2, 4 polarities of VM-COIL as shown in figure below.

10. Adjust the G-Focus until any light around the core disappears.

11. Adjust G-Focus so that the surrounding flash can disappear from the spot.

12. After G-Focus adjustments are complete, adjust R-Focus as above procedures.

13. The B-CRT adjustments can be omitted because the variance of beam focus is small.

(Only Vm-coil is mounted.)

14. Adjust the Focus-pack VR for fine focusing.

15. Press the button on the remote control, and the mode changes to the Convergence Adjustment mode.

S.STD

16. Press the button on the remote control to return to normal viewing.



4-6 SCREEN-JIG

4-6-1 42W5

42W5 Screen Size : X 932, Y 524 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

2 6 .8 4 m m 7 3 .1 9 m m 2 6 .8 4 m m

3 4 .0 0 m m

7 6 .0 0 m m

3 4 .0 0 m m

4-6-2 47W3


3 0 .0 9 m m 8 2 .0 7 m m 3 0 .0 9 m m

8 5 .2 8 m m

4-18

3 8 .1 5 m m

Samsung Electronics


4-6-3 55W3


3 5 .2 7 m m 9 6 .2 0 m m 3 5 .2 7 m m

4 4 .5 1 m m

9 9 .5 0 m m

4 4 .5 1 m m

4-6-4 65W3


4 1 .5 2 m m 1 1 3 .2 5 m m 4 1 .5 2 m m

1 2 1 .5 4 m m

5 4 .3 7 m m



4-6-5 43T6/43T7

43T6 Screen Size : X 885, Y 666 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

2 5 .4 8 m m 6 9 .5 0 m m 2 5 .4 8 m m

4 3 .2 1 m m

9 6 .6 0 m m

4 3 .2 1 m m

4-6-6 48T6

48T6 Screen Size : X 973.4 Y 738.4 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

2 8 .0 3 m m 7 6 .4 5 m m 2 8 .0 3 m m

1 0 7 .1 0 m m



4-6-5 54T6

54T6 Screen Size : X 1099 Y 823 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 1 .6 5 m m 8 6 .3 1 m m 3 1 .6 5 m m

1 1 9 .3 7 m m

4-6-6 62T6

62T6 Screen Size : X 1259.4, Y 948 (X:764 = 22 x 2 + 60 x 12, Y:262 = 17 x 2 + 38 x 6)-PAL MODE

3 6 .2 7 m m 9 8 .8 1 m m 3 6 .2 7 m m

1 3 7 .5 0 m m

6 1 .5 1 m m



4-7 Remote Control for Servicing(Convergence Mode)

Power

TV VCR Cable DVD SET

Convergence Data

LINE Adjust

ENTIRE Adjust

G-Mute

R-Mute

B-Mute

Exit Button

Convergence Data

Left/Right Move Button

Surround S.STD

P.STD

TV

S.Mode

Mute

VOL

Menu

P

Still

Video

Last Data Save button/Canccel

Cg Factory Data

Select Key(Each Inch)

R-Selete

B-Selete

G-Selete

Save Button

Convergence Data

UP/DOWN Move Button

Test Normal

Convergence H-PHASE

Move Button(Left)

Convergence Data

UP/DOWN Move Button

Display P.Size

Text/Mix

PIP

ON

Info.

Sleep Perfect Focus

Scan Swap Locate

Convergence H-PHASE

Move Button(Right)


4-7-1 KEY Function

1. R-SELECT

Press to select RED color.

2. G-SELECT

Press to select GREEN color.

3. B-SELECT

Press to select BLUE color.

4. R-MUTE

Press to mute RED color.

5. G-MUTE

Press to mute GREEN color.

6. B-MUTE TV

Press to mute BLUE color.

7. CANCEL KEY

Press to revert to the previous data during the Convergence Adjustment.

Display

8. TEST/NORMAL

Press to check TV mode in the Convergence Mode.

Press to move a line up/down or left/right.

10. FACTORY DATA SELECT BUTTON

Press to call the factory default values.

S.Mode

11. SAVE BUTTON

After the Convergence Adjustments are completed, press to save data.

S.STD

12. EXIT BUTTON

After the Convergence adjustments are completed, press to exit to TV mode.




13. CURSOR MOVE BUTTON

Press to move the cursor up/down or right/left.

!

UP

LEFT RIGHT

DOWN

@

UP DOWN LEFT RIGHT

# (Mute) Press to move the cursor left or up.

(Video) Press to move the cursor right or down.

(Menu) Press switch the cursor direction horizontally or vertically.

14. CONVERGENCE PICTURE MOVE BUTTON

(Right)

VOL

(Left)

P

(Up)

(Down)

Cg -Data Move Button

15. CONVERGENCE MOVE BUTTON

PIP

ON

Sleep

Press to move the convergence right ( ) or left ( ) .

16. CONVERGENCE DATA ZERO BUTTON

Press to zero the convergence correction data.



42” (42W5)

47” (47W3)

55” (55W3)

43” (43T6

43” (43T7)

48” (48T6)

54” (54T6)

62” (62T6)

65”(65W3)

17. INITIAL DATA SET BUTTON

Changes when applying Almighty-Cg, Module (How to extract the basic Cg Data)

Inch (Type)

Model Name

Representative

Model

SP42W5

SP47W3

SP55W3

SP43T6

SP43T7

SP48T6

SP54T6

SP62T6

SP65W3

Basic Data

Number after entring the Cg-Mode

5-425 (Press in regular order)

5-473(Press in regular order)







Screen Display

Locate

18. Data shift Button Press to transmit data(PAL Mode/NTSC Mode).



4-8 Convergence Adjustment

4-8-1 Convergence Adjustment

Special Notes

✏ A sensor is attached on the center of each side of the Convergence Mode pattern

(see figure below). The sensors are required for normal Perfect Focus function.

✏ Use a screen jig to do the convergence adjustments correctly (Especially, perform correct convergence adjustments on the center of each side where a sensor is located.)

✏ Do the convergence adjustments correctly. Otherwise, any Perfect Focus error can happen.

1. Warm up the TV for a least 30 minutes.

2. Input an PAL Signal.(Use an antenna or AV source.)

Make sure that deflection yoke are properly adjusted so that the center of

Green, Red, Blue pattern is aligned on the center of screen jig.

3. Enter the Convergence Mode by Pressing the remote control keys in the following sequence:

Mute

S.STD

If OSD displayed as shown in figure below, press the key to exit.

Then, redo step 3 to enter the Convergence Mode.

After entering the Convergence Mode, Stand by for about five seconds before doing the adjustments.


Menu

Mute

Menu

P.Size

TV

TV

Alignment and Adjustments or

Samsung Electronics or

4-27


LINE Adjust

S.Mode

VOL P

4-28

Menu

Samsung Electronics

12.

13.

14.

15.

S.Mode


TV



4-8-2 Perfect Focus(Factory Mode)

Up, Down

130

245

150

Perfect Focus

Process : 83%

Exit

Left, Right

130

245

150

Perfect Focus

Process : 83%

Exit

S.STD


4-9 MICOM and Pins Voltage

4-9-1 Pin Layout

GND

N.C

N.C

GND

TTX-CVBS

2.5V

GND

MAIN-AFT

SUB-AFT

KEY2

KEY1

N.C

H-BLK

V-BLK

W.P

SDA2

SCL2

BUS-STOP

SDA1

SCL1

S-RESET

V-MUTE

GND

2.5V

GND

3.3V

DO1

DO4

DO2

DO3

25

26

27

28

29

30

21

22

23

24

17

18

19

20

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

Samsung Electronics


2.5V

GND

N.C

XTAL1

XTAL2

N.C

N.C

N.C

N.C

N.C

OSD-F/B

OSD-B

OSD-G

OSG-R

N.C

N.C

N.C

N.C

N.C

A15

A17

A16

N.C

A7

A13

A12

A14

3.3V

GND

2.5V

56

55

54

53

52

51

60

59

58

57

64

63

62

61

68

67

66

65

72

71

70

69

76

75

74

73

80

79

78

77

4-31


4-9-2 MICOM MODULE Pins

SDA2

SW3

GND

SW2

SUB-AFT

GND

MAIN-AFT

BUS-STOP

ST-BY-LED

RESET

AMP-MUTE

N.C

GND

N.C

SCL2

C-SPK MUTE

KEY 1

PROTECT

KEY 2

GND

N.C

STB-5(V)

IR IN

POWER

TIMER-LED

N.C

GND

V-RESET

SCL1

GND

SDA1

S-RESET

PIN NO. ITEM FUNCTION

29

30

31

32

25

26

27

28

21

22

23

24

17

18

19

20

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

KEY SCAN1

PROTECT PORT

KEY SCAN2

GND

N.C

VCC

REMOCON INPUT

POWER ON/OFF RELAY CONTROL

TIMER LED

N.C

GND

VIDEO RESET

SERIAL CLOCK LINE1

GND

SEREAL DATA LINE1

SOUND RESET

STAND-BY LED

RESET

SOUND AMP MUTE

N.C

GND

N.C

SERIAL CLOCK LINE2

CENTER SPEAKER MUTE

SERIAL DATA LINE2

SW3(CONTROL)

GND

SW2(CONTROL)

SUB TUNER AFT CONTROL

GND

MAIN TUNER AFT CONTROL

IIC BUS STOP

4-32

OUT VOLT

3.27[V]

5[mV]

-

2.08[V]

2.57[V]

-

1.04[V]

3.27[V]

2.95[V]

2.47[V]

0.89[mV]

-

-

-

3.27[V]

3.26[V]

2.07[V]

-

-

2.84[mV]

3.43[V]

-

3.49[V]

4.21[V]

2.28[V)

0.83[mV]

2.25[V]

-

-

4.91[V]

3.74[V]

1.03[V]

Samsung Electronics

GND

N.C

N.C

GND

GND

N.C

AN-LINK

N.C

N.C

OSD-TTX-R

GND

OSD-TTX-G

WP

OSD-TTX-B

3.3[V]

OSD-TTX-FB

VS1

N.C

HS1

N.C

GND

N.C

TTX-CVBS

GND

N.C

GND

GND

N.C

5[V]

H-BLANK

GND

V-BLANK


61

62

63

64

57

58

59

60

53

54

55

56

49

50

51

52

45

46

47

48

41

42

43

44

37

38

39

40

33

34

35

36

N.C

GND

GND

N.C

5[V]

HORIZONTAL BLANK

GND

VERTICAL BLANK

VERTICAL SYNC

N.C

HORIZONTAL SYNC

N.C

GND

N.C

TTX/CAPTION-CVBS

GND

GND

N.C

N.C

GND

GND

N.C

NOT USE

N.C

N.C

ON SCREEN DISPLAY RED

GND

ON SCREEN DISPLAY GREEN

WRITE PROTECT

ON SCREEN DISPLAY BLUE

3.3[V]

OSD/TTX-FB

Samsung Electronics


OUT VOLT

-

168[mV]

-

0.46[V]

-

0.46[V]

3.26[V]

7.31[mV]

-

-

-

-

-

-

-

-

-

-

215.51[mV]

-

-

-

1.19[V]

-

4.96[V]

215.8[mV]

-

-12.10[mV]

-

-

-

-

4-33


4-9-3 PROSCAN MODULE Pins

GND

9[V]

N.C

N.C

N.C

N.C

GND

13.5[V]

N.C

COMP

GND

CG-R

CG-G

CG-B

CG-SYNC

D/F

EW

V-BLK

ABL

VD-

VD+

H-BLK

HD

GND

OSD/TTX-FB

OSD/TTX-B

OSD/TTX-G

OSD/TTX-R

V-RESET

GND

SCL1

SDA1


29

30

31

32

25

26

27

28

21

22

23

24

17

18

19

20

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

EAST WEST OUT

VERTICAL BLANK

ABL(Automatic Brightness Limiter)

VERTICAL DRIVE(-VOLTAGE)

VERTICAL DRIVE(+VOLTAGE)

HORIZONTAL BLANK

HORIZONTAL DRIVE

GND

OSD/TTX-FB

ON SCREEN DISPLAY BLUE IN

ON SCREEN DISPLAY GREEN IN

ON SCREEN DISPLAY RED IN

VIDEO RESET

GND

SERIAL CLOCK LINE

SERIAL DATA LINE

GND

9[V]

N.C

N.C

N.C

N.C

GND

13.5[V]

N.C

COMP

GND

CONVERGENCE RED

CONVERGENCE GREEN

CONVERGENCE BLUE

CONVERGENCE SYNC

DYNAMIC FOCUS

4-34

OUT VOLT

-

-

-

9[V]

-

-

-

14.05[V]

-

27.28[mV]

-

0.27[mV]

0.27[mV]

0.29[mV]

180.03[mV]

1.5[V]

2.26[V]

-12.07[mV]

2.26[V]

3.46[V]

3.53[V[

215.93[mV]

2.38[V]

-

7.29[mV]

0.46[mV]

0.46[mV]

167.99[mV]

2.94[mV]

-

3.42[V]

3.50[V]

Samsung Electronics

GND

DVD-Pr

DVD-Y

DVD-Pb

GND

5[V]-DW2

N.C

N.C

GND

N.C

N.C

N.C

DVD-Pr/R

DVD-Y/G

DVD-Pb/B

FB

5[V]-DW1

VM-Y

SW3

SW2

N.C

GND

PIP-C

PIP-Y CVBS

GND

MAIN-C

MAIN-Y CVBS

N.C

GND

N.C

GND

RF2-CVBS


61

62

63

64

57

58

59

60

53

54

55

56

49

50

51

52

45

46

47

48

41

42

43

44

37

38

39

40

33

34

35

36

GND

DVD-Pr

DVD-Y

DVD-Pb

GND

5[V]-DW2

N.C

N.C

GND

N.C

N.C

N.C

DVD-Pr/R(SCART)

DVD-Y/G(SCART)

DVD-Pb/B(SCART)

FB(SCART)

5[V]-DW1

VM-Y OUTPUT

SW3(CONTROL)

SW2(CONTROL)

N.C

GND

PIP-C INPUT

PIP-Y/CVBS INPUT

GND

MAIN-C INPUT

MAIN-Y/CVBS INPUT

N.C

GND

N.C

GND

RF2-CVBS

Samsung Electronics


OUT VOLT

-

4.89[V]

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

-

1.34[mV]

1.57[mV]

-

4.97[V]

1.97[V]

4.98[mV]

2.08[V]

-

-

1.20[mV]

1.33[mV]

4-35


4-9-4 CONVERGENCE MODULE Pins

N.C

-5[V]

5[V]

GND

GND

H-BLK

V-BLK

GND

GV

GH

RV

RH

GND

GND

BV

BH

N.C

IR

N.C

GND

CG-R

CG-G

CG-B

SDA1

5[V]-CG

GND

D/F

GND

SCL1

CG-SYNC

GND

N.C


29

30

31

32

25

26

27

28

21

22

23

24

17

18

19

20

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

5[V]-CG

GND

DYNAMIC FOCUS

GND

SERIAL CLOCK LINE1

CONVERGENCE SYNC

GND

N.C

CONVERGENCE RED

CONVERGENCE GREEN

CONVERGENCE BLUE

SERIAL DATA LINE1

N.C

INPUT REMOCON

N.C

GND

GND

GND

BLUE VERTICAL OUT

BLUE HORIZONTAL OUT

GREEN VERTICAL OUT

GREEN HORIZONTAL OUT

RED VERTICAL OUT

RED HORIZONTAL OUT

N.C

-5[V]

5[V]

GND

GND

HORIZONTAL BLANK

VERTICAL BLANK

GND

4-36

OUT VOLT

-

-

34.27[mV]

-107.32[mV]

101.52[mV]

-15.83[mV]

104.32[mV]

-88.95[mV]

-

275[mV]

-13.22[mV]

-

-

-4.99[V]

5.24[V]

-

0.27[mV]

0.26[mV]

0.29[mV]

3.5[V]

-

3.7[V]

-

-

5.2[V]

-

1.5[V]

-

3.4[V]

179[mV]

-

5.2[V]

Samsung Electronics

Troubleshooting

5. Troubleshooting

5-1 Convergence Misaligned

Normal Check the input voltage of main

CN801 and sub CN801

Abnormal

Check CNZ02 out pin

(BV, BH, RV, RH, GV, GH)

Normal Abnormal

Check FD101S,FD102S on the sub board

Normal Abnormal

Check connectors

CNZ01

Check the input/output of ICZ103,ICZ104 on the sub board

Normal Abnormal

Replace FD101S,FD102S and check associate circuits

Check the output from

ICZ03, ICZ04 on the sub board

Normal Abnormal

Check the circuits related to ICZ103,ICZ104

Check DY

Check the circuits related to

CNZ02,CNZ04,CNZ05


CG-MDL and FD855S,

FD802S on the SUB PCB


Troubleshooting

5-2 No Sound

Abnormal Check the output volume level of

MAIN CN601

Normal

Check the input/output circuits of IC601

Normal Abnormal

Check IC603

Normal Abnormal

Check the circuits related to IC601

Check IC602

Normal Abnormal


Check IC605

Normal Abnormal


Check various input circuits


Check Speaker


Troubleshooting

5-3 No Raster

Check the input voltage of POWER CORD

Normal Abnormal

Check the Standby voltage of IC841

Normal Abnormal

Abnormal Check the operating status of remote control and POWER S/W

Normal

Check the input voltage

Check the remote control and

CONTROL ASSY

Normal Abnormal

Check MICOM VCC

Normal Abnormal

Check the operating status of MICOM POWER PORT

Normal Abnormal

Check ICS8 01,PC811S


MICOM VCC input

Check the input voltage/waveform of

CRT-PCB CN501,CN401

Normal Abnormal

Check the input/output circuits of IC501,

IC531,IC561

Normal Abnormal

Check the circuits inside SCAN MDL

Check Connector wire

Check QS802

Normal Abnormal

Check the circuits related to IR / MICOM

Check the voltage of CRT,SCREEN

Check the circuits related to the input/output of IC501,IC531,IC561

Check IC831S,PC801S

Normal Abnormal

Check the circuits related to QS802

Check the voltage/waveform of CN801,CN802,CN502A

Normal Abnormal

Check the input of SCAN MDL

Normal Abnormal


SCAN MDL CN03

Check the circuits related to IC831S,PC801S


CN801,CN802,CN502A


SCAN MDL input


MEMO


6. Exploded View & Parts List

6-1 SP42W4HPX/BWT

You can search for the updated part code through ITSELF web site.

URL : http://itself.sec.samsung.co.kr

Samsung Electronics

Exploded View & Parts List

No

28

29

30

31

24

25

26

27

20

21

21

22

17

18

19

20

36

37

38

39

40

32

33

34

35

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

Code No Description;Specification

ASSY-FRONT,MASK;,HIPS HB,G4309,SVM1132,4

ASSY-CABINET,WOOD;,WOOD,MIJU,42W5

SUN-SCREEN

SCREEN-TINT;42W,958*550,T=0.7,P=052

SCREEN FRESNEL;42W,960*552,T=2.0

BADGE-BRAND;72MM,AL FORGING,SVM1132,SAMS

MODULE-FOCUS PACK ASS’Y;PJT TV,F301-P03A

ASSY PRT;SP42W5HFX/XEO,J52A

KNOB-POWER;42W5,ABS,HB,G3676,COT

SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-,

CABINET-PANEL,CONTROL;42W5,HIPS,HB,G4309

WINDOW-RMC,LED;42W5,PC,CLR

KNOB-CONTROL;42W5,ABS,HB,G3676,COT

SCREW-TAPTITE;RH,+,B,M4,L12,ZPC(BLK),SWR

GUIDE-KNOB,CONTROL;42W5,ABS HB,G3676,SVM

CABINET-FRONT,BOT;42W5,HIPS,HB,G4309,SVM

BADGE-DECORATION;42W5,AL,NI,RS

HOLDER-SIDE,A/V;42W5,ABS HB,G3676,SV-704

DOOR-AV;42W5,ABS HB,G3676,SV-704P

VELCRO-A;COMMANDO,BST1 1/4H


VELCRO-B;COMMANDO,BST1 1/4H

VELCRO-B;COMMANDO,BST1 1/4H



MIRROR-FRONT;42W5,FSM,870*633*446

BRACKET-MIRROR,ASSY;42W5,SECC,T1.0,01123


CABINET-BACK,TOP;42W5,HIPS,HB,G4309

SCREW-WOOD;HH,+,M4,L19,ZPC(BLK),SWRCH18A

ASSY COVER P-TERMINAL ANT;SP43T6HPX/SAP,


ASSY CHASSIS;SP42W5HPX/SAP,J54A

SPACER-COVER,DUST;43,54,62J9,SPONGE 94HF

BRACKET-SCREEN,ASSY(R);42W5,SECC,T1.0,SC

BRACKET-SCREEN,ASSY(TOP);42W5,SECC,T1.0,

BRACKET-SCREEN,ASSY(L);42W5,SECC,T1.0,SC

BRACKET-SCREEN,ASSY(BOT);42W5,SECC,T1.0,

SCREW-TAPTITE;-,SWRCH18A,M4,L12,HH,+,PC,

INLAY-SUPPORT;42W5,PS SHEET,T0.5,94V0


Q’ty Remark S.N.A

1

2

1

3

2

4

7

1

3

1

1

1

1

3

1

1

1

1

20

1

2

1

1

1

1

1

1

1

4

1

1

1

1

1

1

1

1

1

1

1

1 S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

6-1

Exploded View & Parts List

6-2 SP43T7HPX/SED



6-2

No

29

30

31

32

25

26

27

28

21

22

23

24

17

18

19

20

37

38

39

40

33

34

35

36

41

42

13

14

15

16

9

10

11

12

7

8

5

6

3

4

1

2

Code No Description Specification

CABINET-FRONT,MASK TOP;43T7HP,HIPS,HB,G4

SUN SCREEN-AG;43J8,910*692*2,T=82%,G=110

SCREEN-TINT;43,908*690,P,DNP

SCREEN FRESNEL;43N,910*692,T2

BRACKET-SCREEN,RIGHT-ASSY;43T7,SECC,T1.0

BRACKET-SCREEN,LEFT-ASSY;43T7,SECC,T1.0,

BRACKET-SCREEN,TOP-ASSY;43T7,SECC,T1.0,S

BRACKET-SCREEN,BOT-ASSY;43T7,SECC,T1.0,S

SCREW-SPECIAL;BH,+,-,M4,L12(11),ZPC(BLK)

CABINET-FRONT,BOT;43T7,HIPS,HB,G7666,SVM

WINDOW-LED;43T7,PMMA,T3.0

WINDOW-LED;43T7,PMMA,T3.0

SPRING ETC-CS;-,SUS304,-,-,OD6,N7,OD6,-,

HOLDER-POWER,RMC;43T7,ABS HB,G3676,CR-CO

WINDOW-RMC;43T7,PC,CLR

COVER-DECORATION;43T7,ABS,HB,WHT,SVM6145



KNOB-CONTROL;43T7,ABS,HB,G3676,SILVER


HOLDER-SIDE,A/V;43T7,ABS HB,G3676,SVM-11

DOOR-AV;43T7,ABS HB,G3676,SVM-1132

CABINET-WOOD;43T7,WOOD,ENCLOSED SPK

SPEAKER;25W,8OHM,90DB+/-3DB,60HZ+/-12HZ

SCREW-WOOD;-,SWRCH18A,M4,L16,PH,+,-,-,ZP

SPEAKER;20W,8OHM,95DB,1300HZ

BADGE-BRAND;PJLCD,AL,T1.5,72,12.5,,DGN-S

CABINET-BACK,TOP;43T7,HIPS,HB,G4309


MIRROR-BACK;43T7,SSM,795*569*554*(78)

BRACKET-MIRROR,ASSY;42W5,SECC,T1.0,01123

SCREW-TAPPING;TH,+,2,M4,L15,ZPC(BLK),SWR

TRANS FBT-H/V DISTRIBUTOR;FUW50A002B,PJC

BRACKET-CRT,MAIN;54,SECC,T1.6,-,-,-,-

CABINET-BACK,BOT;43T7,HIPS,HB,G4309


ASSY COVER P-TERMINAL ANT;SP43T6HPX/SAP,

SCREW-TAPPING;TH,+,2,M4,L15,ZPC(BLK),SWR

ASSY CHASSIS;SP43T7HPX/XTL,J54A,INDIA

SPACER-COVER,DUST;43T7,SPONGE 94HF-1,T3.



Q’ty

2

6

9

1

1

1

12

2

1

2

1

1

1

2

4

4

1

1

1

3

4

4

1

3

1

1

1

1

1

1

1

1

20

1

1

1

1

1

1

1

1

1

Remark

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

S.N.A

Samsung Electronics

Electrical Parts List



7. Electrical Parts List

7-1 SP42W4HPX/BWT

Loc. No.

1

1

2

1

1

2

2

2

2

2

2

2

2

2

2

2

1

2

2

2

1

1

1

1

1

1

1

2

2

2

2

1

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

2

1

1

1

1

1

1

2

1

1

2

1

1

Code No. Description ; Specification Remark

BP91-00453A ASSY CPT-R SP42W5HPX/XEU,J54A,CRT-R ASSY

BP91-00454A ASSY CPT-G SP42W5HPX/XEU,J54A,CRT-G ASSY

BP91-00455A ASSY CPT-B SP42W5HPX/XEU,J54A,CRT-B ASSY

BP91-00336A ASSY CHASSISS P42W4HPS/XEF,J54A

BP94-00232A ASSY PCB MISC-CRT PCB DP,SP42W5HPS/XEU,J

AA59-00171A MODULE-FOCUS,PACK SVP-5200,S300-P3,-,-,-

AA39-20577B LEAD CONNECTOR-ASSY P54A/SVP-55W3HD,UL16

BP94-00193A ASSY PCB MISC-A/V FRONT DP,BP94-00192A,S

AA95-01841C ASSY SUB-PCB,SENSOR DP,PCL545R,P54A,AA95

BP94-00238A ASSY PCB MISC-VM DP,HCM4215W3S/XAA,P55A

AA96-20130A ASSY POWER CORD -,CP2/NO(4.0R),H/C150,KJ

BP91-00005E ASSY ,42W4

AA61-00094C HOLDER-RAIL PCJ533R,ABS,-,-,-,BLK,HB,480

AA61-00097A HOLDER-WIRE -,NYLON 6/6,-,-,-,NTR,-

AA61-00616B HOLDER-CRT,MAIN 54J7,DP,-,-,-,-,AA61-005

BP61-00075A HOLDER-JERSEY,ASSY W3,ABS V0,GRAY,63-000

AA61-00533B BRACKET-GRILLE 43,54,62J8,SECC-1 ,T0.5,-

BP61-00019A HOLDER-PALLET 42W5,HIPS HB,BLK

AA64-02724A CABINET-WOOD 42W5,WOOD,SDE8336R

AA60-10051A SCREW-WOOD -,SWRCH18A,M4,L16,PH,+,-,-,ZP

BP61-00035A BRACKET-GRILLE 42W5,SECC-1,T1.0

AA61-10247A BRACKET-FOCUS S46DS,SECC,T1.0,-,-,-,-

AA60-10051B SCREW-WOOD -,SWRCH18A,M3.5,L11,RH,+,-,-,

3001-001107 SPEAKER 20W,8OHM,95DB,1300HZ


AA39-00086A LEAD CONNECTOR-ASSY ,2.2UF,200MM,REC,REC

AA98-00049B ASSY-LEAD,CON -,LEAD-CON,CORE,AA39-20505

AA61-00617B BRACKET-CRT,MAIN DP,54J7,AA61-00475B

6006-001094 SCREW-ASS’Y WOOD WW,HH,+,M7,L32,ZPC(YEL)

BP96-00013C ASSY COVER P ,ABS

AA64-02727P CABINET-FRONT,MASK TOP 42W4,HIPS,HB,G430

AA61-01133A VELCRO-B COMMANDO,BST1 1/4H

AA64-02211E BADGE-BRAND 72MM,AL FORGING,SVM1132,SAMS

6003-001019 SCREW-TAPTIT RH,+,B,M4,L12,ZPC(BLK),SWR

BP96-00014A ASSY COVER P-C/FRONT,BOT DP,42W5,HIPS HB

AA64-02725A CABINET-FRONT,BOT 42W5,HIPS,HB,G4309,SVM

AA64-02743A BADGE-DECORATION 42W5,AL,NI,RS

BP73-00001A RUBBER-SHEET 42W5,NBB RUBBER,GRAY,10*20

AA61-01132A VELCRO-A COMMANDO,BST1 1/4H

6003-001019 SCREW-TAPTITE RH,+,B,M4,L12,ZPC(BLK),SWR

BP98-00090F ASSY K/D-PANNEL,CONTROL SP42W5HPS/XEF,J5

BP64-00101A CABINET-PANEL,CONTROL DP,42W4,HB,G4309

BP64-00077A KNOB POWER 42W4,HB,G3676,42W4,ABS HB G36

AA61-60003J SPRING ETC-CS -,SUS304,-,-,OD6,N7,OD6,-,

BP64-00078A WINDOW REMOCON-LED 42W4,PC,42W4,PC,CLEAR

BP64-00102A KNOB CONTROL DP,42W4,ABS,HB,G3676

BP61-00139A GUIDE-KNOB CONTROL 42W4,DP,ABS,HB,G3676

BP94-00314A ASSY PCB MISC-CONTROL SP42W4HPS/XEF,J54A

AA61-20129A HOLDER-WIRE -,NYLON-66,-,-,-,NTR,DAFC-25

AA61-01132A VELCRO-A COMMANDO,BST1 1/4H



6003-001023 SCREW-TAPTITE RWH,+,B,M3,L10,ZPC(YEL),SW

BP64-00008E CABINET-BACK,BOT DP,42W5,AA64-02729C 19.

BP64-00009A CABINET-BACK,TOP DP,42W5,AA64-02728A 38.

AA40-00050A TUNER TCLW3101PD18A(S),TCLW3101PD18A

AA40-00051A TUNER TCPW3001PC18B(S),TCPW3001PC18B

AA39-30007A CBF IF -,T,100mm,1365#26

AA67-00204C MIRROR-FRONT DP,42W5,FSM,870*633*446,AA6

BP61-00012A BRACKET-MIRROR DP,42W5,AA61-01123A,11.8K

BP61-00123A BRACKET-SCREEN,TB DP,42W5,SECC,T1.0,BP61

BP61-00124A BRACKET-SCREEN, DP,42W5,SECC,T1.0,BP61

AA67-00193A SCREEN-TINT 42W,958*550,T=0.7,P

Loc. No.


1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

AA67-00193B SCREEN FRESNEL 42W,960*552,T=2.0

BP39-00009A LEAD CONNECTOR-ASSY P54A/SVP-42W5,UL2547

BP39-00047A LEAD CONNECTOR P55A/HCM4215W,UL2547#26,U

BP96-00077G ASSY COVER P-TERMINAL,ANT DP,42W5,HIPS,V

BP26-00004A TRANS FBT-H/V DISTRIBUTOR FUW50A002B,PJC

AA61-00049B HOLDER-BOX-,PP,-,-,-,NTR,V0,AA61-20285A

BP61-00043B HOLDER-SENSOR W9,PC HB,VIOLET

AA64-60449B INLAY-COVER SP-434JMF,PS,T0.5,149.3X69.5

BP64-00029A INLAY-SUPPORT 42W5,PS SHEET,T0.5,94V0

AA65-30013A CLAMPER CORE-WIRE -,NYLON-66,V0,-,NTR,DA

AA65-30018A CLAMPER CORE-WIRE DONG-A,NYLON-66,-,-,-,

AA65-30104C CLAMPER CORE-WIRE ALL MODEL,NYLON 66,V2,

AA65-30008A CLAMPER CORE-CORD-,PE,HB,-,BLK,-

BP61-00052A HOLDER-WIRE PJTV,NYLON,66,NATURAL

6003-001022 SCREW-TAPTITERH,+,B,M3,L12,ZPC(BLK),SWR


AA60-10011A SCREW-TAPTITE -,SWRCH18A,M4,L12,HH,+,PC,

6005-001003 SCREW-WOOD HH,+,M4,L19,ZPC(BLK),SWRCH18A

6003-001339 SCREW-TAPTITE HH,+,B,M4,L15,ZPC(BLK),SWR

AA63-00533A SHEET ,LDPE 1.0+HDPE 0.015,1000,WHT

0201-001059 ADHESIVE-SIL #9590,WHT,-,CARTRIGE

0203-001329 TAPE-OPP MASKING ANT-300P,T0.07,W15.0,L5

AA60-00072B SPACER-COVER,DUST 43,54,62J9,SPONGE 94HF

BP73-00004A RUBBER-CAP 42W5,SILICONE,WHT,RUBBER

AA69-01678A PACKING-COVER,BOT 42W5,H-3 AB,C3,YEL,910

BP69-00019D PACKING CASE-OUT 42W4,H-3 YEL,C3,SESA

AA69-01651A CUSHION-SET 42W5,PS FOAMED,C=0.02

BP59-00008A REMOCON ,TM65A,COMMOANDO,J54A,49,L/GRA

BP68-00026A MANUAL USERS SP43T6HPX/BWT,RUS,W/P100G,J

AA39-00006A CABLE RCA ,3000MM

4301-000120 BATTERY-MN 1.5V,-,AA,14.5x50mm,-

AA68-50509A LABEL-BOX A/P 90(G),ALL MODEL,-,WHT,L250

AA68-00344A LABEL-TRANSFER BOX -,TF-53B5DF,-,BLACK,1

AA68-00526A LABEL-RATING ART PAPER(90),ALL MODEL,LAM

AC68-00347A LABEL-TRANSFER RATING ALTA RESISTENCIA,X

AA68-00340A LABEL-WARRANTY -,-,-,WHT,75MM,20MM

AA68-00345A LABEL-TRANSFER WARRANTY -,TF-53B5DF,-,BL

AA69-00862A BAG PE -,HDPE PE FOAM,T0.03,W400,H240

AA69-00744L BAG-SHEET -,HDPE PE FOAM,T0.015,W1650,H1

AA63-10002A BAND-TIE NYLON66 V2,L100,NTR

AA63-10007D BAND ,W18.5

0203-000402 TAPE-KRAFT KRAFT,T0.17,W18,L50,BLK

AA68-02415A CARD-RTF COLORIT 54 CREMA,MOJO80G,SPA,A

AA02-00022A TAPE ETC SESA,T0.3,75,132,BLK

BP94-00239A ASSY PCB MISC-DY-JACK DP,HCM4215W3S/XAA,

AA68-00971A LABEL-BACK,DOLBY ,T/P ,75,35,BLACK,VIRTU

AA65-30105A CLAMPER CORE-WIRE ALL MODEL,NYLON 66,V2,

AA65-30110A CLAMPER CORE-WIRE ALL MODEL,NYLON 66,V2,

AA65-00020A CLAMPER CORE-WIRE 55W9,NYLON 66

AA69-01876A PALLET ALL MODEL,WOOD,600,1200,120

AA61-00618C GUIDE-FLOW 54J8,J7,ABS,IVORY,V0

AC68-00285A LABEL-TAPE TRANSPARENT SESA,A/P,T0.3,-,-

AA68-01120A MANUAL SERVICE -,-,CIS,A4,6PAGE(FOLD),W/

AA68-01402A MANUAL-GOOD WILL LETTER ,CIS,B5,1PAGE,A/


Electrical Parts List



7-2 SP43T7HPX/SED

1

2

2

2

2

3

2

2

2

2

2

2

2

2

2

2

2

2

2

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

2

Loc. No.


1

1

1

1

1

AA95-01841C ASSY SUB-PCB,SENSOR DP,PCL545R,P54A,AA95

BP91-00525A ASSY CPT-R SP43T7HPX/XEF,J54A

BP91-00526A ASSY CPT-G SP43T7HPX/XEF,J54A

BP91-00527A ASSY CPT-B SP43T7HPX/XEF,J54A

BP91-00372A ASSY CHASSIS SP43T7HPS/XEF,J54A

ASSY PCB MISC-CRT PCB

BP94-00232A ASSY PCB MISC-CRT PCB DP,SP42W5HPS/XEU,J

AA59-00171A MODULE-FOCUS,PACK SVP-5200,S300-P3,-,-,-

AA39-20577B LEAD CONNECTOR-ASSY P54A/SVP-55W3HD,UL16

BP94-00353A ASSY PCB MISC-A/V FRONT DP, BP96-00011E,

BP94-00238A ASSY PCB MISC-VM DP,HCM4215W3S/XAA,P55A

AA96-20130A ASSY POWER CORD -,CP2/NO(4.0R),H/C150,KJ

ASSY K/D-CABINET,WOOD

BP98-00244A ASSY K/D-CABINET,WOOD 43T7, AA64-02731C,

AA60-10051A SCREW-WOOD-,SWRCH18A,M4,L16,PH,+,-,-,ZP

AA60-10051B SCREW-WOOD-,SWRCH18A,M3.5,L11,RH,+,-,-,

AA61-00094C HOLDER-RAILPCJ533R,ABS,-,-,-,BLK,HB,480

AA61-00097A HOLDER-WIRE-,NYLON 6/6,-,-,-,NTR,-

AA61-00508D HOLDER-JERSEYW3,ABS V0,GRAY,G4309

AA61-00533B BRACKET-GRILLE43,54,62J8,SECC-1 ,T0.5,-

AA61-00506B HOLDER-CRT,MAIN43,54,62J8,HIPS,-,-,-,BL

AA61-00864A HOLDER-PCBW3,HIPS,V0,BLK


AA61-01213A BRACKET-GRILLE 43T7,SECC,T0.5

AA61-10247A BRACKET-FOCUS S46DS,SECC,T1.0,-,-,-,-

AA64-02731C CABINET-WOOD 43T7,WOOD,SESA,COMMANDO

AA65-00014B CLAMPER CORE-WIRE GPM-51A,PP,HB,-,BLK,-

BP61-00019A HOLDER-PALLET 42W5,HIPS HB,BLK



AA39-00086A LEAD CONNECTOR-ASSY ,2.2UF,200MM,REC,REC

AA98-00049A ASSY-LEAD,CON -,LEAD-CON,CORE,AA39-20505

3301-001201 CORE-FERRITE AE,21x11x32mm,1500,280G

BP96-00016B ASSY COVER P-MASK DP,43T7,AA64-02733D,SV

BP64-00015B CABINET-FRONT,BOT DP,43T7 EUR,AA64-02732

BP64-00017B CABINET-BACK,BOT DP,43T7,AA64-02735B1

BP64-00016A CABINET-BACK,TOP DP,43T7,AA64-02734A

AA40-00050A TUNER TCLW3101PD18A(S),TCLW3101PD18A

AA40-00051A TUNER TCPW3001PC18B(S),TCPW3001PC18B

AA39-30007A CBF IF -,T,100mm,1365#26

AA67-00205D MIRROR-BACK

DP,43T7,SSM,795*569*554*(78)

BP61-00012A BRACKET-MIRROR DP,42W5,AA61-01123A,11.8K

BP61-00016C BRACKET-SCREEN,TB DP,43T7,BP61-00109A

BP61-00017C BRACKET-SCREEN,RL DP,43T7,BP61-00110A

AA61-00617B BRACKET-CRT,MAIN DP,54J7,AA61-00475B

AA67-00195A SCREEN-TINT 43,908*690,P,DNP

AA67-00115B SCREEN FRESNEL 43N,910*692,T2

BP39-00009A LEAD CONNECTOR-ASSY P54A/SVP-42W5,UL2547


Loc. No.


1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

BP96-00077G ASSY COVER P-TERMINAL,ANT DP,42W5,HIPS,V

BP26-00004A TRANS FBT-H/V DISTRIBUTORFUW50A002B,PJC

AA61-00049B HOLDER-BOX -,PP,-,-,-,NTR,V0,AA61-20285A

BP61-00043B HOLDER-SENSOR W9,PC HB,VIOLET

AA64-60449B INLAY-COVER SP-434JMF,PS,T0.5,149.3X69.5

BP64-00029A INLAY-SUPPORT 42W5,PS SHEET,T0.5,94V0

AA65-30013A CLAMPER CORE-WIRE -,NYLON-66,V0,-,NTR,DA

AA65-30018A CLAMPER CORE-WIRE DONG-A,NYLON-66,-,-,-,

AA65-30104C CLAMPER CORE-WIRE ALL MODEL,NYLON 66,V2,

AA65-30008A CLAMPER CORE-CORD -,PE,HB,-,BLK,-

BP61-00052A HOLDER-WIRE PJTV,NYLON,66,NATURAL



6003-001023 SCREW-TAPTITE RWH,+,B,M3,L10,ZPC(YEL),SW


AA60-10011A SCREW-TAPTITE -,SWRCH18A,M4,L12,HH,+,PC,

6005-001003 SCREW-WOOD HH,+,M4,L19,ZPC(BLK),SWRCH18A

AA63-70002A SHEET -,PE FOAM,T1.0,-,-,-,50G

6006-001094 SCREW-ASS’Y WOOD WW,HH,+,M7,L32,ZPC(YEL)

0201-001059 ADHESIVE-SIL #9590,WHT,-,CARTRIGE

0203-001329 TAPE-OPP MASKING ANT-300P,T0.07,W15.0,L51

6005-001004 SCREW-WOOD HH,+,M4,L27,BLK,SWRCH18A

AA60-00072C SPACER-COVER,DUST 43T7,SPONGE 94HF-1,T3.

BP73-00004A RUBBER-CAP 42W5,SILICONE,WHT,RUBBER

BP69-00021A PACKING-COVER,BOT 43T7,H-3 AB,C3,YEL,965

BP69-00020A PACKING CASE-OUT 43T7,H-3 YEL,C3,1045,63

AA69-01652A CUSHION-SET43T7,PS FOAMED,C=0.02

BP59-00008A REMOCON ,TM65A,COMMOANDO,J54A,49,L/GRA

BP68-00040A MANUAL USERS

SP42W5HP,FRE,W/P100G,J54A,B


SP42W5HP,GER,W/P100G,J54A,B


SP42W5HP,ITA,W/P100G,J54A,B

AA39-00006A CABLE RCA ,3000MM

4301-000120 BATTERY-MN 1.5V,-,AA,14.5x50mm,-

AA68-50509A LABEL-BOX A/P 90(G),ALL MODEL,-,WHT,L250

AA68-00344A LABEL-TRANSFER BOX TF-53B5DF,-,BLACK,1

AA68-00526A LABEL-RATING ART PAPER(90),ALL MODEL,LAM

AC68-00347A LABEL-TRANSFER RATING ALTA RESISTENCIA,X

AA68-00340A LABEL-WARRANTY -,-,-,WHT,75MM,20MM

AA68-00345A LABEL-TRANSFER WARRANTY -,TF-53B5DF,-,BL

AA69-00862A BAG PE -,HDPE PE FOAM,T0.03,W400,H240

AA69-00744L BAG-SHEET -,HDPE PE FOAM,T0.015,W1650,H1

AA63-10002A BAND-TIE YLON66 V2,L100,NTR

AA63-10007D BAND ,W18.5

0203-000402 TAPE-KRAFT KRAFT,T0.17,W18,L50,BLK

AA68-02415A CARD-RTF COLORIT 54 CREMA,MOJO80G,SPA,A

AA02-00022A TAPE ETC SESA,T0.3,75,132,BLK

6009-001296 SCREW-SPECIAL BH,+,-,M4,L12(11),ZPC(BLK)

BP64-00044A INLAY-VENT 43T7,PS SHEET,T0.5


BP94-00239A ASSY PCB MISC-DY-JACK DP,HCM4215W3S/XAA,

BP94-00328A ASSY PCB MISC-CONTROL POWER DP,SP43T7HPS

BP94-00329A ASSY PCB MISC-CONTROL SIDE P,SP43T7HPS/

6002-000522 SCREW-TAPPING TH,+,2,M4,L15,ZPC(BLK),SWR

AA68-00971A LABEL-BACK,DOLBY ,T/P ,75,35,BLACK,VIRTU

AA65-30105A CLAMPER CORE-WIREALL MODEL,NYLON 66,V2,

AA65-30110A CLAMPER CORE-WIREALL MODEL,NYLON 66,V2,

AA65-00020A CLAMPER CORE-WIRE 55W9,NYLON 66

AA63-60122J SPACER-FELT SPD-50P3H,FELT,L530,D20,T0.3

AA69-01087Q PALLET-CKD CKD,PAPER,975,745,130

AA61-00618C GUIDE-FLOW 54J8,J7,ABS,IVORY,V0

AC68-00285A LABEL-TAPE TRANSPARENTSESA,A/P,T0.3,-,-


8. Block Diagram

8-1 Current System

STAND-BY

POWER

MAIN

POWER

K A 7 8 R 0 5

5 . 0 V

E E R 5 3 4 5

8 . 5 V

1 3 7 m A

1 . 3 5 m A

E E R 5 3 4 5

1 1 0 V

E E R 5 3 4 5

1 2 V

E E R 5 3 4 5

1 3 . 5 V

3 8 0 m A

E E R 5 3 4 5

- 2 0 V

E E R 5 3 4 5

+ 2 0 V

E E R 5 3 4 5

+ 2 9 V

1 . 2

1 0 5 m A m A

6 8 0 m A

8 2 5 m A

8 8 m A

M i c o m / E e p r o m 1 3 7 m A

K A 2 7 8 R A 0 5 ( A ) 5 V

K A 2 7 8 R A 0 5 ( A ) 5 V

K A 2 7 8 R A 0 5 ( A ) 5 V

3 0 5 0 5 V

H i g h V o l t

V M 1 1 0 V

T u n e r 3 3 . 0 V

V e r t i c a l D R I V E R

E W , P O R T E C T , H V R E G

C R T

K A 7 8 0 8

K A 2 7 8 R A 0 9

8 . 0 V

9 . 0 V

K A 7 8 R 1 2 1 2 . 0 V

C G A M P

K A 7 9 0 5 ( - 5 . 0 V )

C G A M P

E W

S o u n d A M P

4 4 5 m A

8 0 m A

4 5 5 m A

3 4 0 m A

1 . 0 3 A

1 3 m A

3 m A

1 2 m A

9 0 m A

3 m A

1 4 0 m A

1 0 0 m A

1 4 0 m A

6 5 0 m A

3 0 m A

8 1 5 m A

1 0 m A

8 8 m A

M I C O M , S O U N D

S C A N 1

S C A N 2

C G M D L

F B T

4 4 5

8 0

4 5 5

3 4 0 m A m A m A m A

H E A T E R

V e r t i c a l D R I V E 1 6 . 5 V

V e r t i c a l D R I V E - 1 3 . 5 V

C R T 2 0 0 V

6 2 0 m A

2 1 0 m A

1 9 0 m A

1 7 m A

S O U N D

S C A N M D L

S O U N D

C G - M D L

1 4 0 m A

1 0 0 m A

1 4 0

3 0 m A m A

Samsung Electronics

Block Diagrams

8-1

Block Diagrams

8-2 Power Supply System

INPUT

RECTFIER

RBV-606

Switching IC

STR-F6459

HOT

Line Filter

10mH / 2.45A

1mH / 5A

Stand-by

Trans

PS2561

AC IN

Line Filter

10mH / 2.45A

1mH / 5A

Line Filter

10mH / 2.45A

FUSE

7V / 0.13A

8-2

POWER

TRANS

EER 5345

PC

PS2561

Power

Control

7805

COLD

OUTPUT

RECTFIER

Error AMP

SE11ON

Micom

5V / 0.13A

1 1 0 V / 1 . 2 A

1 3 . 5 V / 0 . 3 8 A

8 . 5 V / 1 . 3 5 A

2 0 V / 0 . 8 2 A

- 2 0 V / - 0 . 6 8 A

2 9 V / 0 . 8 8 A

1 2 V / 0 . 1 1 A

Samsung Electronics

8-3 Deflection System

1 2 V / 0 . 1 1 A

1 1 0 V / 1 . 2 0 A

POWER

Trans

2 0 V / 0 . 8 3 A

- 2 0 V / 0 . 6 8 A

Samsung Electronics

F B T

±13.5V

E / W

C o l l e c t o r

V e r t i c a l

O u t p u t

R - D Y

G - D Y

B - D Y

E / W

A M P

H o r i z a n t a l

O u t p u t

H V

R e g u l a t i o n

P R O T E C T

H - D r i v e

H e a t e r

2 0 0 V

H i g h V o l t a g e

F o c u s V o l t a g e

H D

C R T

D r i v e

( R / G / B )

R - C Y

S T K 3 9 2 - 0 1 0

C o n v e r g e n c e A M P

S T K 3 9 2 - 0 1 0

G - C Y B - C Y

Block Diagrams

8-3

Wiring Diagrams

9. Wiring Diagram

9-1 Connection(Progressive)

A

M

P

S

U

B

CENTER

GND

SURROUND

MUTE

30V

30V

GND

GND

8 P

O

L

C

O

N

T

R

KEY2

GND

GND

KEY- 2

KEY- 1

STD- 5V

GND

KEY- 3

I R

TI MER- LED

STD- LED

SDA1

SCL 1

GND

1 2 P

KEY2

GND

GND

S2- C

GND

S2- I D

S2- Y

GND

AV3- R

GND

GND

AV3- L

AV3- I D

GND

AV4- CVBS

1 2 P

S

I

D

E

A

/

V

C R T

B

SCREEN

GND

210V

N. C

GND

HEATER

GND

12V

B

GND

I K

SPOT

GND

VM-

VM-OUT

C N 5 0 2

1 0 P

9 P

210V

N. C

GND

HEATER

GND

12V

R

GND

I K

SPOT

R

GND

G

GND

B

GND

I K

SPOT. K

D/ F

VM-

VM- OUT

6 P 117V

NC

GND

13. 5V

GND

VM- Y

SCREEN

GND

C R T

G

VM-

VM-OUT

210V

N. C

GND

HEATER

GND

12V

R

GND

I K

SPOT

D/ F

GND

C N 5 0 3

1 1 P

VM-

VM-OUT

3 P X 3

V M

R / G /B

VM-

VM-OUT

SCREEN

GND

210V

N. C

GND

HEATER

GND

12V

R

GND

I K

SPOT

D/ F

GND

SCREEN

C R T

R

6 P

VM-

VM-OUT

D /F

B L O C K

GND

Dy nami c

F oc us

R F oc us

G F oc us

B F oc us

F O C U S

P A C K

D Y - B D Y - G D Y - R

D Y

- M O D U L E

E

A

S

P

K

E

R

Samsung Electronics

KEY- 2

KEY- 1

STD- 5V

GND

KEY- 3

I R

TI MER- L ED

STD- L ED

SDA1

SCL1

GND

C N 9 0 2

1 1 P

L - OUT

GND

R- OUR

GND

C N 6 0 1

4 P

TDA7625

M

E

R

T

U

N

S

E

R

T

U

N

C N Y 0 1

12P

S2- C

GND

S2- I D

S2- Y

GND

AV3- R

GND

GND

AV3- L

AV3- I D

GND

AV4- CVBS

M

I

C

O

M

STD- 5V

GND

I R

M

D

L

S

C

A

N

R

GND

G

GND

B

GND

I K

SPO

D/ F

C N 2 0 1

6 P

117V

NC

GND

13. 5V

GND

VM- Y

C N 8 0 1

15 : C O MP

14 : H - B LK

13 : G ND

12 : V- B LK

11 : 1080i

10 : AB L

9 : VD +

8 : VD -

7 : E W

6 : P R O TE C T

5 : G ND

4 : H D

3 : G ND

2 : STB - 5V

1 : P O WE R

C N 8 0 2

14 : 29V

13 : 29V

12 : 29V- GND

11 : 29V- GND

10 : - 20V

9 : GND

8 : 8.5V

7 : 8.5V

6 : GND

5 : 13.5V

4 : SUB- MUTE

3 : GND

2 : N.C

1 : 125V

GND

5V

UP

GND

5V

RI GHT

GND

5V

L EFT

GND

5V

DOWN

C

G

M

D

L

RH

GND

RV

GH

GND

GV

BH

GND

BV

C N 2 0 2

9 P

MA IN

15 : CO MP

14 : H- BLK

13 : GND

12 : V- BLK

11 : 1080i

10 : ABL

9 : VD+

8 : VD-

7 : EW

6 : PROTEC T

5 : GND

4 : HD

3 : GND

2 : STB- 5V

1 : POWER

1 5 P

14 : 29V

13 : 29V

12 : 29V- G ND

11 : 29V- G ND

10 : - 20V

9 : G ND

8 : 8.5V

7 : 8.5V

6 : G ND

5 : 13.5V

4 : SUB- MUTE

3 : G ND

2 : N.C

1 : 125V

1 4 P

M A S T E R - S W

G ND - R G B ( 3 P )

3 : - 24V

2 : GND

1 : 24V

3 P

P O W E R

S U B

H1/ H2/ V1/ V2

T R A NS

4 P

1 P

SCREEN

210V

N. C

GND

HEAT

GND

12V

C N 5 0 2 A

D e fe lc tio n

F B T

A C - I N P U T

C O N V - A M P

CNZ05

C Y - B

CNZ01

RH

GND

RV

GH

GND

GV

BH

GND

BV

CNZ02

C Y - G

C O N V - A M P

CNZ04

C Y - R

D Y - B D Y - G D Y - R

9-1

10. Schematic Diagrams

10-1 MAIN 1

TP02

TP01

Schematic Diagrams

TP01

TP02


Schematic Diagrams

10-2 MAIN 2

TP03

TP04

TP05

10-2

TP03

TP04

TP05

Samsung Electronics

10-3 MAIN 3

Samsung Electronics

TP06

TP07

Schematic Diagrams

TP06

TP07

10-3

Schematic Diagrams

10-4 MAIN 4

10-4

TP14 TP13

TP12

TP11

TP10

TP09

TP08

TP15

TP16

TP17

TP18

TP19

TP20

TP20 TP14 TP08

TP15 TP09

TP16 TP10

TP17 TP11

TP18 TP12

TP19 TP13

Samsung Electronics

10-5 MICOM

Samsung Electronics

Schematic Diagrams

10-5

Schematic Diagrams

10-6 CRT


10-7 SUB 1

TP21

Schematic Diagrams

TP21


Schematic Diagrams

10-8 SUB 2

TP23

10-8

TP22

TP22

TP23

Samsung Electronics

10-9 SUB 3

Samsung Electronics

Schematic Diagrams

10-9

Schematic Diagrams

10-10 CONVERGENCE ( SDC12 - 1 )


10-11 CONVERGENCE ( SDC12 - 2 )

Samsung Electronics

Schematic Diagrams

10-11

Schematic Diagrams

10-12 PRO SCAN 1


10-13 PRO SCAN 2

Samsung Electronics

Schematic Diagrams

10-13

Schematic Diagrams

10-14 AV FRONT


10-15 VM

Samsung Electronics

Schematic Diagrams

10-15

Schematic Diagrams

10-16 CONTROL


10-17 DY JACK, SENSOR

DY JACK SENSOR

Schematic Diagrams


Samsung SVP-5200P Specifications

PROJECTION TV RECEIVER

1. Precautions

2. Reference Information

3. Specifications

4. Alignment and Adjustments

5. Troubleshooting

6. Exploded View & Parts List

7. Electrical Parts List

8. Block Diagram

STAND-BY

POWER

MAIN

POWER

POWER

Trans

9. Wiring Diagram

10. Schematic Diagrams

Related manuals

Samsung

SP-43T8HP

Samsung

21S1

Samsung

SVP-5200P

Samsung

DW21G5

Samsung

CY-TP55

Samsung

CS21D90X/BWT

Samsung

PL-H403W

Samsung

CS21K5

Samsung

SV-A25B

Samsung

DVD-905

Samsung

21K2

Samsung

TXK3276