User Manual
User Manual
L7
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG
D-83071 Stephanskirchen
Germany
Kontaktinformationen unter / For contact information visit
www.arri.com
Ident.No. L5.31899.0
L02485
ENGLISH
Table of Contents
1. General 4
1.1 Important Notes and Safety Instructions
4
1.1.1 General Notes
4
1.1.2
Important Safety Instructions
4
1.2 Description and Features of your Lamphead
5
1.2.1 Properties
5
1.2.2 Product features
5
2. General Lamphead Overview
6
3. Setting up and Securing the Fixture
7
4. Basic Functions
8
5. Setting Options
8
5.1 Possible Settings via On-board Control
9
5.1.1 Overview of on-board control
9
5.1.2 Menu levels of the on-board control
10
5.1.3 Setting the operating modes
11
5.1.4 Setting the color temperature (CCT mode)
11
5.1.5 Setting the color (HSI mode)
11
5.1.6 Setting intensity
11
5.1.7 Setting the fan function
11
5.1.8 Setting the DMX address
11
5.1.9 Signal lost behavior
12
5.1.10 Selecting the DMX profile
12
5.1.11 Turning lights on/off and status request of on-board control
12
5.1.12 Status request
12
a) Operating hours
12
b) DMX version
12
c) Software version
12
d) Operating temperature
12
e) Availability
12
5.1.13 Error messages
13
5.1.14 Error messages
13-14
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
2
www.arri.com
Possible Settings via DMX
14
5.2.1 DMX profiles
14
5.2.2 DMX In / Pin allocation
14
5.2.3 DMX Implementation table
5.2.4 Conversion CCT value to DMX %
5.2.5 RDM functions
5.3 LSeries Manager
25
6
Technical Data
26 - 27
7
EC Declaration of Conformity, Service
ENGLISH
5.2 15 - 22
22
23 - 25
28
© 2014 Arnold & Richter Cine Technik GmbH & Co. KG Betriebs KG (ARRI).All rights reserved. ARRI assumes no responsibility for the accuracy
and completeness of the information. Information are subject to change without notice. ARRI and affiliated companies disclaim liability for any
damage, direct or indirect loss, economic loss or any other loss occasioned by the use of, inability to use or reliance on the information contained in
this document. The ARRI logo, the ARRI name and all other trademarks in this document pertaining to services or products by ARRI or its affiliates
and subsidiaries are trademarks owned or licensed by ARRI or its affiliates or subsidiaries.
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
3
ENGLISH
1. General
1.1 Important Notes and Safety Instructions
1.1.1 General Notes
■■ ARRI L Series fixtures are intended for professional use in the studio and on location and may only be
operated by qualified persons.
■■ Read these instructions carefully before using the device for the first time. The following text contains
important information for safe handling.
■■ Observe the safety instructions and warnings for your own personal safety.
■■ All components comply with the following European standards and directives:
Low voltage directive 2014/30/EU
EMC directive 2014/30/EU
RoHS directive 2011/65/EU
■■ Keep these instructions for possible subsequent owners.
■■ Help protecting our environment by disposing the packing material at your local recycling center.
■■ Use only original ARRI spare parts and accessories (more information at www.arri.com).
1.1.2. Important Safety Instuctions
■■
DANGER OF LIFE - MAINS VOLTAGE!
Disconnect the device from the mains voltage
before replacing a damaged fuse!
Never bridge a fuse!
■■
■■
CAUTION ! Risk of burns !
The housing and the cooling fins can reach high temperatures.
Keep a safety distance of 20" (0,5 m) to adjacent surfaces on all sides.
Keep the cables away from the fixtures.
Do not cover ventilations slots and cooling fins.
CAUTION ! High Beam Intensity !
Do not look into the light emission aperture of the fixture.
■■
■■
■■
■■
Safety devices may only be removed for service purposes by qualified personnel !
Do not lift or suspend the fixture at the mains cable !
Note the technical data on page 29 and 30.
Do not use the fixture or accessories if they display any visible damage on any component.
In case of damage the respective parts must be exchanged or you have to contact an
ARRI Service station (see www.arri.com).
■■ L7 fixtures must not be connected to dimmer systems or dimmer channels in Non-Dim mode.
Doing so will damage the electronic system of the fixture.
■■ Check the fixture for the following possible damage before every use:
part
possible damage
housing, lens
fissures, cracks, deformed
cables
deformed, cut, scorched
plug
deformed, broken, scorched
plug connections
damaged
inner thread
overwound
Also read and follow the additional safety leaflet "Operating your ARRI Lampheads safely" L5.70731.E
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
4
www.arri.com
ENGLISH
1.2 Description and features of your Lamphead
The L7 range lampheads are equipped with an electronically controlled LED light source. You can use them like a conventional
tungsten Fresnel fixture but with far higher energy efficiency. The newly developed optical system offers a continuous
focus range of 15-50° half peak angle and real 'Fresnel' characteristics: an extremely uniform light field and clean shadow
rendition. The various types of L-series produce white or colored light with adjustable color temperature and green / magenta saturation. For more information, see "Specifications" on page 26. The light spectrum has been specifically designed for excellent color
rendition. All fixtures can be controlled over USB interface, DMX 512 / RDM protocol or on-board control panel (if equipped).
1.2.1 Properties
■■
Focus
Versatility is the key element in traditional Fresnels, especially the ability to spot and flood the beam as needed. Whether it’s
a flood field for a pullback shot or a tight spot for a bright highlight, the continuous focusability of the L7 performs
just as expected.
■■
Versatile beam characteristics
The L7 provides the same ability as conventional Fresnel lenses to cut set elements and shape the light field
with barndoors and flags.
■■
Even light field
Clear, defined shadows have traditionally been a trait only of single source tungsten and daylight fixtures. ARRI L7 Fresnels provide the same single shadow properties designers expect, delivering natural results.
■■
Vibrant colors, full-spectrum lighting
True-to-life color rendition is an outstanding feature of the L range, comparable to a full-spectrum tungsten source. The fully tuneable White light of the L7 C can be adjusted for different skin tones, camera sensors and mixed-light environments. Full gamut color mixing enables the rendition of all color shades, making color filters dispensible.
■■
Cool light beam
Like all LED light sources the L7 does not emitt infrared or UV radiation and thus no forward heat, making talent feel comfortable in the light beam.
The ARRI L range combines all advantages of LED technology and the traditional Fresnel lens. It integrates seamlessly into established working practices, so that designers can stick with their creative techniques and studios will have no need to change their
operating procedures.
1.2.2 Product features
■■
Focus knob
True Blue-style focus knobs provide precise adjustment and rapid flood-to-spot with only three turns. Knobs on both sides of the fixture ensure easy access from all positions.
■■
Sliding stirrup
The sliding stirrup design enables precise compensation for front-end accessories.
■■
Yoke
With an extremely slim profile, the extruded aluminum yoke provides high strength without added weight. An optional pole-
operated yoke allows full operation of pan and tilt from the floor and is therefore a popular choice for many studios.
■■
Tilt lock
The high strength tilt lock provides extremely secure locking, eliminating movement and slippage and ensuring that the fixtures will stay where you put them.
■■
DMX control
All functions of the L7 are controllable through DMX. The L7 is also fully RDM compatible and is equipped with a feedback channel for reporting all set parameters including system status and hours on the light engine.
■■
On-board control
For location applications the L7 is equipped with an on-board control for manual adjustment of intensity, color temperature and plus/minus Green as well as hue and saturation (functions available depending on type).
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
5
ENGLISH
2. Lamphead overview
1 Power switch (optional)
2 Power cable
8
3 Fuse holder
4 USB port (Mini USB)
5 DMX input
6 DMX through
9
7 Handle
11
7
8 Spigot
9 Stirrup
16
10 Tilt lock
11 Top latch
12 Safety catch
13 Focus knob or P.O. gear
12
14 Control and indicator panel (not at all versions)
1
15 Stirrup bracket
16 Lens holder
2
17 Tilt lock lever
13
14
15
17
P.O. - Version
13
10
4
3
5
6
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
6
www.arri.com
ENGLISH
3. Setting up and securing the fixture
■■
Tools needed
Torx screwdriver no. 20
Torque wrench / Allen key no. 10 (50 Nm)
■■ Adjusting the stirrup
On delivery the stirrup (9) is in the basic position, which means it is tilted to the back.
Use the Torx screwdriver no. 20 to slightly loosen the screws on both sides of the stirrup bracket (15) and pull the stirrup
bracket towards the rear of the lamphead. The lever of the tilt lock (10) has to be loosened, so that you can tilt the stirrup (9) upwards.
In order to position the stirrup at the ideal balance point move it to a position halfway in-between the front and rear of the lamphead housing. Then tighten the screws at the stirrup bracket (15) again. Now tilt the stirrup to the desired angle and tighten the tilt lock lever. For better leverage, press the knob on the tilt lock lever (17) and turn the lever to the desired
position.
■■
Mounting the spigot
Place the spigot (8) and the spacer onto the boring in the stirrup (9), insert the screw with washer and spring washer from below and fasten it with the torque wrench to 50 Nm = 37 lbf ft (pound force feet).
■■
Installation of the PC software
Download the latest LSeries Manager version from the internet (download center: http://www.arri.com/l-series/downloads).
Be aware that the installation can only be performed, if you have administrative rights. If your user profile does not grant
administrative rights you have to let the installation file (.exe) run as follows:
Right-click on the file „start as administrator“.
Start the program by double-clicking on the generated shortcut.
After the installation is completed you can connect your lamphead via USB cable to your computer. The LSeries Manager automatically detects the connected lampheads. Make sure that no other DMX program is communicating with the lamphead. You can operate one lamphead with any one USB port.
Tip: After the installation is complete, we recommend connecting the lamphead before you start the LSeries Manager for the first time. Doing this will complete the driver installation and prevent a possible connection time-out.
Note: Wait with connecting your lamphead to the computer until the installation of the LSeries Manager is complete. The LSeries Manager allows you to operate several L7 lampheads and also update them simultaneously.
Securing the lamphead and the accessories
■■
When mounting the fixture in a hanging position, additionally secure the fixture with a safety cable from the mounting pipe or
truss through the fixture stirrup. The safety cable must be properly dimensioned for the fixture and application and must be
kept short.
■■
The carrying capacity of the safety rope must be rated at a minimum of 10 times the weight of the lamphead system including
accessories.
■■
Be aware of the maximum allowed tilt angle of 90° up and 90° down.
■■
When the lamphead is operated in a hanging position, ensure that the accessories are installed correctly: top latch (11) locked,
optional barndoor safety catch (12) snapped in.
■■
Stands must be set up in a stable position and capable of carrying the load of the lamphead including accessories and cables!
Also refer to our safety leaflet "Operating Your ARRI Lampheads Safely"; L5.40731.E.
CAUTION! Lateral load can cause deformation or breaking of the spigot (8) or the stirrup (9)!
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
7
ENGLISH
4. Basic functions
■■ Securing the fixture
The lamphead must be fastened at its stirrup (9) in a standing or hanging position. The spigot (8) must be inserted into the
husk of a matching stand or a matching holding device and must be clampt in and secured there.
■■ Rotation and tilt
The lamphead can be rotated after the screw at the stand or holding device has been loosened. In order to change the tilt,
loosen the tilt lock (10). After rotating or tilting the lamphead, the screws or lock levers must be tightened again.
■■
Adjusting the beam angle
The beam angle can be continuously adjusted by turning the focus knob (13). When you do this the entire lens unit is moved out of or into the lamphead housing.
This mechanism protects the fixture in two ways:
· A predetermined breaking point prevents damage at the lamphead if the focus knob is turned with too much torque.
· A self-impeding gear prevents that the position of the lens unit changes while the lamphead is operated in a tilted position.
■■ Using accessories for light design
Accessories for light design, such as a barndoor or filter holders, can be inserted into the holding brackets on the front of the lamphead. To do this proceed as follows:
· Firmly press the button at the side of the top latch; the top latch flips upwards.
· Insert the accessory from the upside into the holding brackets, until the safety catch (12) engages. Slightly tilt the safety catch with your finger for support.
· Close the top latch (11) and make sure that the hook of the top latch engages in the holding ring of the accessory.
■■
DMX interface
The lamphead is equipped with an RDM/DMX interface with a waterproof input socket. The not waterproof DMX distributor box which is mounted at this socket has one DMX in and out and has the purpose of looping the DMX line throuhg to the next lamphead. It can be removed after loosening the fixing screw.
■■
USB interface
The lamphead is also equipped with a USB interface with a mini USB slot, which can be used for updating the fixture's
internal firmware, for adjusting operating parameters and for service purposes. The service tool "LSeries Manager" allows you to configure your lamphead via this interface, you can download the LSeries Manager from the ARRI homepage free of charge. (Download center: http://www.arri.com/l-series/downloads)
■■
Turning on and operation
After you have turned on the power switch (or after connecting to mains power for lampheads without a power switch) the lamphead will need a short start-up time before it lights up. The lamphead will operate with the previously used setting. It can now be controlled via the DMX interface or the on-board control.
CAUTION! Hight beam intensity ! Do not look into the ligth emission aperture of the lamphead.
5. Setting Options
You have four options to configure or control your lamphead:
Type
control
configuration
yes
yes
USB - LS Manager
no
yes
DMX - mixing console or computer
yes
no
RDM - USB on RDM Box with PC software
yes
yes
on-board control
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
8
www.arri.com
ENGLISH
5.1 Possible settings via on-board control
5.1.1 Overview of on-board control
17
18
26
15
19
16
20
B
C
21
24
22
25
23
Depending on the model, your lamphead is equipped with one of the following display or control panels:
· simple display field (A)
· on-board control with LC display and intensity control (B)
· on-board control with LC display, intensity and color control (C)
A
no.
name
short description
15
POWER-/STATUS-LED display
lights up yellow when the lamphead is on.
16
DATA display
lights up blue when a valid DMX signal has been detected
17
FUNCT - button
1. function: changes between CCT & HSI mode
2. function: jump one menu level UP
18
ENTER - button
1. function: jump one menu level DOWN
2. function: confirm settings
3. function: „flash“ arrow for activating quick selection
(calling memory 1 oder memory 2)
19
+ / UP / step up value
navigate within a menu level or step up values
(keep button pressed for stepping up rapidly)
20
- / DOWN / step down value
navigate within a menu level or step down values
(keep button pressed for stepping down)
21
rotary knob INTENSITY
set intensity
22
rotary knob CCT / HUE
set color temperature or hue
23
rotary knob GN / SAT
set green-magenta correction or saturation
24
memory button 1
safe or retrieve settings
25
memory button 2
safe or retrieve settings
26
display
Status LEDs at on-board control:
green LED lights up
status OK / lamphead active
blue LED lights up
receiving DMX or RDM data
red LED flashes at 500ms rhythm *
lamphead will shortly reach over temperature
red LED lights up permanently *
over temperature reached
red LED goes out and Green LED lights up *
lamphead has cooled down and can be turned on again
red LED flashes rapidly at 250ms rhythm *
calibration data could not be loaded
* display lights up red when LED is lit
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
9
ENGLISH
5.1.2 Menu levels of the on-board control
During the operation of the lamphead the selected operating mode with the current value is displayed. On the first menu level the
values for INTENSITY, CCT/HUE and GN/SAT can be retrieved via the + / - buttons. The menu point STATUS, confirmed with
ENTER, takes you to the next level which displays information on faultless operation and the temperature. To retrieve values for
operating hours, DMX version and software version, press ENTER to jump to the third level. The FUNCT key takes you back to the
previous menu level.
Note: The horizontal arrow in the display symbolizes the possibility to jump to the next menu level by pressing ENTER.
menu level 1
display
Intensity
e.g. 24 %
CCT/HUE
e.g. 2900K / 16°
GRN/SAT
e.g. -0,57 / 100
menu level 2
OK or ERROR
display
menu level 4
e.g. 501 t
e.g. 3.1
e.g. 1.70.0
e.g. 42.1° (temperature)
HOUR (operating hours)
e.g. P.001
DMX V (DMX version)
STATUS
SETUP
SW (software version)
menu level 3
PROT (protocol number)
HOLD
LSIG
BOUT
CHAN
H2MF
ON or OFF
e.g. C.017
DMX (DMX settings)
INDC (lights on control)
FAN (fan modes)
OFF
LOW
HI
ALOW (from 80%)
AHI (from 80%)
VARI (at avg. 158° F)
PASS
HI 45 (only L7 Active)
Note: In setup or status mode the settings option remains active until another function is executed. In all other modes the
display will go back to the respective mode after 2 seconds.
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
10
www.arri.com
In CCT mode the lamphead generates White light with optimized color rendition CRI > 95.
In HSI mode the lamphead generates colored light. If saturation is set very low, the lamphead will generate White light, but with
optimized color rendition.
ENGLISH
5.1.3 Setting the operating modes
Press the FUNCT key (17) briefly to switch from CCT mode to HSI mode or vice versa.
5.1.4 Setting the color temperature and Green-magenta adjustment in CCT mode
With the rotary knob CCT/HUE (22) the color temperature can be adjusted continuously.
The rotary knob GN/SAT (23) serves for continuous green-magenta adjustment.
You can retrieve the currently set value for Green-magenta adjustment by pressing the keys + (19) or - (20) repeatedly until GRN is
displayed on the left side of the display (e.g. +0.23). The setting for color temperature is always displayed (e.g. 4150K).
5.1.5 Setting the color in HSI mode (only L7-C)
With the rotary knob CCT/HUE (22 ) you can adjust the value for hue continuously.
Use the rotary knob GN/SAT (23) for continuous adjustment of saturation.
You can retrieve the currently set value for saturation by pressing the keys + (19) or - (20) repeatedly until SAT is displayed on the
left side of the display (e.g. 45). The setting for hue is always displayed (e.g. 4118°).
5.1.6 Setting intensity in both operating modes
With the rotary knob INTENSITY (21) you can continuously adjust intensity in both operating modes. You can retrieve the currently
set value for intensity by pressing the keys + (19) or - (20) repeatedly until INTENSITY is displayed on the left side of the display
(e.g. 24%).
5.1.7 Setting the fan functions
You can set the different fan functions via the on-board control from menu level 3.
Proceed as follows:
Press the keys + (19) or - (20) repeatedly until SETUP is displayed in the left lower corner of the display (27).
Confirm with the ENTER key (18). Press the key + (19) or - (20) repeatedly until FAN is shown in the display (27). Confirm with
ENTER (18) again. The currently used fan mode is displayed.
By pressing the keys + (19) or - (20) you can select the desired fan mode (see table below). Confirm your selection with the ENTER
key (18). The fan will now work in the desired mode. Press the FUNCT key (17) twice to leave this menu level.
Fan mode
OFF
L7 Hybrid
L7 Active
x
Description of mode
Fan is turned off, it may occur that the lamphead turnes itself off due to overheating.
Once the lamphead has cooled down it can be turned on and used again.
LOW
x
HI
x
Fan operates constantly at maximum speed
A-LOW
x
Fan operates from 80% intensity with 1050 rev/min
A-HI
x
VARI
x
PASS
x
HI 45
x
Fan operates constantly at low speed (silent)
Fan operates from 80% intensity with maximum speed
x
Fan is controlled via the light-engine temperature, fan starts at approx.
158° F, steps speed up or down automatically
70°C /
No fan, light output is reduced by 20%
x
Optimized for an ambient temperature of 45°C / 113° F, fan operates at max. speed,
light output is reduced by approx 15%
5.1.8 Setting the DMX address
Go to menu level 4 to set the DMX start address via the on-board control.
Proceed as follows:
Press the keys + (19) or - (20) repeatedly until SETUP is displayed in the left lower corner of the display (27).
Confirm with the ENTER key (18). Press the key + (19) or - (20) repeatedly until DMX is shown in the display (27). Confirm with
ENTER (18) again. Press the key + (19) or - (20) repeatedly until CHAN is shown in the display (27). When you press the ENTER
key now the currently used DMX start address is displayed and flashes three times. Use the keys + (19) or - (20) to select a value
from C.001 to C.506 an confirm your selection with the ENTER key (18). The DMX start address is now set. Press the FUNCT key
(17) three times to leave this menu level.
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
11
ENGLISH
5.1.9 Signal lost behavior
3 signal lost options are available:
HOLD: DMX hold function, latest DMX values are reminded forever.
Re power the device clears the hold function or sending new DMX-Values.
BOUT: BOUT means black out, after a DMX signal lost, the LedSpot dim immediately to zero.
H2MF: Same as HOLD, but after 2 minutes the LedSpot dim to zero.
5.1.10 Selecting the DMX profile
In order to select one of the 15 available DMX profiles via the on-board control you have to navigate to menu level 4. To get there,
proceed as follows:
Press the keys + (19) or - (20) repeatedly until SETUP is displayed in the left lower corner of the display (27).
Confirm with the ENTER key (18). Press the key + (19) or - (20) repeatedly until DMX is shown in the display (27). Confirm with
ENTER (18) again. Press the key + (19) or - (20) repeatedly until PROT is shown in the display (27). When you press the ENTER
key the currently used DMX profile is displayed. Use the keys + (19) or - (20) to select a value from P.001 to P.015 and confirm your
selection with the ENTER key (18). The DMX profile is now selected and flashes three times.
Press the FUNCT key (17) three times to leave this menu level.
5.1.11 Turning on-board control lights on/off
In order to turn the lights at the on-board control on or off you have to navigate to menu level 3. To get there, proceed as follows:
Press the keys + (19) or - (20) repeatedly until SETUP is displayed in the left lower corner of the display (27).
Confirm with the ENTER key (18). Press the key + (19) or - (20) repeatedly until INDC is shown in the display (27). When you
press the ENTER key, the current settings are displayed. Use the + (19) or - (20) keys to select either ON or OFF and confirm with
ENTER (18). The light on the display (26) and LED signals (15 and 16) are now turned on or off. Press the FUNCT key (17) twice
to leave this menu level.
5.1.12 Status request
In order to request the status via the on-board control proceed as follows:
a ) Read operating hours
Press the keys + (19) or - (20) repeatedly until SETUP is displayed in the left lower corner of the display (27).
Confirm with the ENTER key (18). Press the key + (19) or - (20) repeatedly until HOUR is shown in the display (27). When you
press the ENTER key the operating hours are displayed (e.g. 501 t). Press the FUNCT key (17) three times to leave this menu
level.
b ) Read DMX version
Press the keys + (19) or - (20) repeatedly until SETUP is displayed in the left lower corner of the display (27).
Confirm with the ENTER key (18). Press the key + (19) or - (20) repeatedly until DMXV is shown in the display (27). When you
press the ENTER key the version is displayed (e.g. 3.1). Press the FUNCT key (17) three times to leave this menu level.
c ) Read software version
Press the keys + (19) or - (20) repeatedly until SETUP is displayed in the left lower corner of the display (27).
Confirm with the ENTER key (18). Press the key + (19) or - (20) repeatedly until SW is shown in the display (27). When you press
the ENTER key the version is displayed (e.g. 1.70.0). Press the FUNCT key (17) three times to leave this menu level.
d ) Read operating temperature
Press the keys + (19) or - (20) repeatedly until SETUP is displayed in the left lower corner of the display (27).
Confirm with the ENTER key (18). Press the key + (19) or - (20) repeatedly until the temperature (e.g. 42.1°) is shown in the display
(27) . Press the FUNCT key (17) twice to leave this menu level.
e ) Read availability
Press the keys + (19) or - (20) repeatedly until SETUP is displayed in the left lower corner of the display (27).
Confirm with the ENTER key (18). In the display (27) you can see OK or an error code (e.g. E.004 / see table with error messages
on next page). Press the FUNCT key (17) twice to leave this menu level
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
12
www.arri.com
Code
Error
Solution
E.003
Controller over temperature
Let the lamphead cool down. After that the status LED should light up
Green again. The lamphead is available for operation.
Set the fader to 0 and then set the desired value.
E.004
Light Engine over temperature
See solution for E.003
E.005
Power supply over temperature
See solution for E.003
E.006
Calibration data faulty or read error of
light engine memory
NOTICE: Loss of calibration data can only be solved
in the factory. (You might have to exchange the light engine
and carry out calibration again.)
E.007
Invalid PWM value calculation
This merely serves as a notification that a fault has occurred during
calculation.
E.008
Invalid values during calculating step 1
See solution for E.007
E.009
Invalid values during calculating step 2
See solution for E.007
E.010
Fan error. Exeeding deviation from
pre-set speed or fan outage. This error
can only be detected in fans with speed
indicator (3 wire fan).
CAUTION: Only a trained service person is allowed to fix this error!
Set the fan to LOW or HI and see if it starts rotating, in order to determine if there is an electrical malfunction.
All mechanical tests or repairs may only be carried out by a trained service technician.
ENGLISH
5.1.13 Error messages
From SW version 1.72.0
E.011
On-board control could not be detected,
or on-board control ID has not been programmed at the lamphead.
If the on-board control is working, error E.011 can be ignored. However,
if the on-board control remains dark (no LED lights up) we recommend
contacting a service partner. They can then carry out detailled analyses.
E.012
Temperature sensor(s) are defective or
deviation within NTC values too high.
One or more temperature sensores are defective or the deviation within
the individual NTCs or BNTCs exceeds the variation tolerance of 54° F.
Check the error log (LSeries Manager) to see which temperature sensores are affected. Ask your service partner to fix this error.
5.1.14 Short-Cuts
From firmware version 1.74.1 the demo mode, setting the DMX address and the DMX protocol may be called up using short-cuts.
To activate a short-cut:
-
-
-
-
Press and hold ENTER, until JUMP appears in the display (from every menu).
Press and hold FUNCT to activate the demo mode, pressing FUNCT again deactivates the demo mode.
Press PLUS: Setting the DMX address.
Press MINUS: Setting the DMX protocol.
JUMP disappears after 3 s without pressing a button or after pressing ENTER again.
Demo mode:
In demo mode the fixture calls up a loop:
-
-
-
L7-T: Dimmer sequence. Choose the speed with the dimmer knob from slow (60 s per loop) to fast (1 s per loop).
L7-TT and DT: Color temperature chase from warm to cold and back. The dimmer knob controls the brightness,
the CCT knob controls the speed (60s – 1s per loop).
L7-C: Color chase and color temperature chase. The dimmer knob controls the brightness. The CCT knob controls
the speed (60s – 1s per loop). The GN knob is used to control the saturation of the colors or to switch to
color temperature chase. With GN at “0” the color temperature chase is active.
Turning the knob clockwise increases the saturation up to 100%.
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
13
ENGLISH
Pressing JUMP and FUNCT or FUNCT alone deactivates the demo mode. The demo mode can be activated and deactivated using
the menu Setup -> DEMO either.
Shift key:
This short-cut is only available in the main menu. Press ENTER, until a small arrow starts blinking in the display.
Memory 1 or memory 2 calls up one of two factory settings.
All short-cuts are only available on fixtures with onboard control.
5.2 Settings options via DMX
5.2.1 DMX profile
The ARRI L7 range offers 15 DMX profiles, which can be pre-configured by the user. The 8-bit modes should be used with basic
DMX control consoles (dimming consoles). The most common modes for operation are mode 01 and mode 02. ARRI recommends
the use of the 16-bit mode in combination with a DMX control console, which supports functions up to 16-bit resolution in order
to obtain premium results. The increased resolution over the 8-bit mode provides even smoother dimming and continuous color
adjustment. Additionally there is a „Coarse/fine“ mode which allows you to perform a coarse and fine adjustment with two indiviual
DMX channels. The Coarse / Fine modes utilize two DMX channels for most parameters and provide increased resolution over the
8-bit modes for users without 16-bit compatible control consoles. In case of a failure of the DMX signal the last valid DMX value will
be retained. The setting can be changed at any time with the rotary knobs at the on-board control.
White and RGBW:
This is the most common mode of operation. It provides control over intensity, color temperature, +/- Green, and individual Red,
Green, Blue, and White color channels.
White:
Simplified White-only mode for use when the number of available channels on a DMX control board is limited. It provides control
over intensity, color temperature, and +/- Green.
White & HSI:
Provides control over intensity, color temperature, +/- Green, color hue, and color saturation. HSI = Hue, Saturation, Intensity. The
advantage of HSI compared with RGBW is, that colors and intesity are exactly the same in each lamphead due to the applied color
algorithms.
RGBW:
Simplified White-only mode for use when the number of available DMX channels is limited. It provides control over intensity and
individual Red, Green, Blue, and White color channels.
HSI:
Simplified Hue, Saturation and Intensity mode for use when the number of available channels on a DMX control board is limited.
Note: For DMX Implementation Table see page 15 to 20 or http://www.arri.com/l-series/downloads
Note: Depending on the selected DMX profile the channels required for each lamphead should be allocated, if necessary up to 16
channels (required for DMX protokoll mode 6) right away.
5.2.2 DMX In / Pin allocation
pin 3
5-pin-XLR (female connector)
pin 1 : ground (screen)
pin 2 : signal (-)
pin 3 : signal (+)
pin 4 : not used
pin 5 : not used
pin 4
pin 2
pin 1
pin 5
In
Out
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
14
www.arri.com
Available DMX Modes
fixture type
8 Bit Modes
16 Bit Modes
Coarse / Fine Modes
1 DMX channel per function required
2 DMX channels per function required
1-2 DMX channels per function required
L7-T
01 - Dimm 8 *
02 - Dimm 16
03 - Dimm C/F (Coarse/Fine)
L7-DT
01 - White 8 Bit
02 - White 16 Bit
03 - White C/F
L7-TT
01 - White 8 Bit
02 - White 16 Bit
03 - White C/F
L7-C
01 - White & RGBW 8 Bit *
06 - White & RGBW 16 Bit
11 - White & RGBW C/F
02 - White 8 Bit
07 - White 16 Bit
12 - White C/F
03 - White & HSI 8 Bit
08 - White & HSI 16 Bit
13 - White & HSI C/F
04 - RGBW 8 Bit
09 - RGBW 16 Bit
14 - RGBW C/F
05 - HSI 8 Bit
10 - HSI 16 Bit
15 - HSI C/F
ENGLISH
5.2.3 DMX IMPLEMENTATION TABLE V3.3
* standard modes (factory settings)
L7-T Mode 01 - DIMM 8 BIT chanel no.
function
DMX value
1
intensity
000
output value
...
255
0
...
100
steps per bit
unit
0,3922
%
notes
L7-T Mode 02 - DIMM 16 BIT
channel no
1
2
function
DMX value
HI
intensity
00000
LO
...
output value
65535
0
...
100
steps per bit
unit
0,0015
%
steps per bit
unit
notes
L7-T Mode 03 - DIMM C/F
channel no.
function
DMX value
output value
1
intensity
000
...
255
0
...
100
0,3922
%
2
intensity (fine)
000
...
255
0
...
10
0,0392
%
notes
L7-DT Mode 01 - White 8 BIT
channel no.
function
DMX value
output value
steps per bit
unit
1
intensity
000
...
255
0
...
100
0,3922
%
2
color temperature
000
...
255
5.000
...
6.500
5,88
K
000
...
010
neutral / no effect
-
011
...
020
full minusgreen
-
3
green / magenta value
021
...
119
-99
120
...
145
neutral / no effect
146
...
244
1
245
...
255
full plusgreen
...
-1
1
notes
% GN
(1)
% GN
(1)
...
99
1
-
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
15
ENGLISH
L7-DT Mode 02 - White 16 BIT
channel no.
1
2
3
4
function
DMX value
HI
intensity
LO
color temperature
5
HI
LO
HI
green / magenta
value
6
LO
output value
steps per bit
unit
00000
...
65535
0
...
100
0,0015
%
00000
...
65535
5.000
...
6.500
0,0229
K
00000
...
05000
neutral / no effect
-
05001
...
10000
full minusgreen
-
10001
...
29999
-99.995
30000
...
40000
neutral / no effect
40001
...
59999
0.005
60000
...
65535
full plusgreen
...
-0.005
...
99.995
0.005
notes
% GN
(1)
% GN
(1)
0.005
-
L7-DT Mode 03 - White C/F
channel no.
function
DMX value
steps per bit
unit
1
intensity
000
...
255
0
...
100
0,3922
%
2
intensity (fine)
000
...
255
0
...
10
0,0392
%
3
color temperature
000
...
255
5.000
...
6.500
5,88
K
4
color temperature (fine)
000
...
255
0
...
255
1
K
000
...
010
neutral / no effect
-
011
...
020
full minusgreen
-
5
green / magenta value
output value
021
...
119
-99
120
...
145
neutral / no effect
146
...
244
1
245
...
255
full plusgreen
...
-1
1
notes
% GN
(1)
% GN
(1)
...
99
1
-
L7-TT Mode 01 - White 8 BIT
channel no.
function
DMX value
output value
steps per bit
unit
1
intensity
000
...
255
0
...
100
0,3922
%
2
color temperature
000
...
255
2.600
...
3.600
3,92
K
000
...
010
neutral / no effect
-
011
...
020
full minusgreen
-
3
green / magenta value
021
...
119
-99
120
...
145
neutral / no effect
146
...
244
1
245
...
255
full plusgreen
...
-1
1
notes
% GN
(1)
% GN
(1)
...
99
1
-
L7-TT Mode 02 - White 16 BIT
channel no.
1
2
3
4
function
DMX value
HI
intensity
LO
color temperature
5
HI
LO
HI
green / magenta
value
6
LO
output value
steps per bit
unit
00000
...
65535
0
...
100
0,0015
%
00000
...
65535
2.600
...
3.600
0,0153
K
00000
...
05000
neutral / no effect
-
05001
...
10000
full minusgreen
-
10001
...
29999
-99.995
30000
...
40000
neutral / no effect
40001
...
59999
0.005
60000
...
65535
full plusgreen
...
-0.005
...
99.995
0.005
16
% GN
(1)
% GN
(1)
0.005
-
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
notes
channel no.
function
DMX value
1
intensity
000
...
255
0
...
2
intensity (fine)
000
...
255
0
...
3
color temperature
000
...
255
2.600
4
color temperature (fine)
000
...
255
0
000
...
010
neutral / no effect
011
...
020
full minusgreen
021
...
119
-99
120
...
145
neutral / no effect
146
...
244
1
245
...
255
full plusgreen
5
green / magenta value
output value
steps per bit
unit
100
0,3922
%
10
0,0392
%
...
3.600
3,92
K
...
255
1
K
notes
ENGLISH
L7-TT Mode 03 - White C/F
...
-1
...
99
1
% GN
(1)
% GN
(1)
1
-
L7-C Mode 01 - White & RGBW 8 BIT
channel no.
function
DMX value
steps per bit
unit
1
master intensity
000
...
255
0
...
100
0.3922
%
2
color temperature
000
...
255
2,800
...
10,450
30
K
000
...
010
neutral / no effect
-
011
...
020
full minusgreen
-
3
green / magenta value
output value
021
...
119
-99
120
...
145
neutral / no effect
146
...
244
1
...
-1
1
notes
% GN
(1)
% GN
(1)
(2)
...
99
1
245
...
255
full plusgreen
4
white-color crossfade
000
...
255
0
...
100
0.3922
%
5
red intensity
000
...
255
0
...
100
0.3922
%
6
green intensity
000
...
255
0
...
100
0.3922
%
7
blue intensity
000
...
255
0
...
100
0.3922
%
8
white intensity
000
...
255
0
...
100
0.3922
%
L7-C Mode 02 - White 8 BIT
channel no.
function
DMX value
1
intensity
000
2
color temperature
3
green / magenta value
output value
...
255
steps per bit
unit
0
...
100
0.3922
%
...
10,400
30
K
000
...
255
2,800
000
...
010
neutral / no effect
-
011
...
020
full minusgreen
-
021
...
119
-99
120
...
145
neutral / no effect
146
...
244
1
245
...
255
full plusgreen
...
-1
1
notes
% GN
(1)
% GN
(1)
...
99
1
-
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
17
ENGLISH
L7-C Mode 03 - White & HSI 8 BIT
channel no.
function
DMX value
1
master intensity
000
2
color temperature
3
4
green / magenta value
white-color crossfade
output value
...
255
steps per bit
unit
0
...
100
0.3922
%
...
10,450
30
K
000
...
255
2,800
000
...
010
neutral / no effect
011
...
020
full minusgreen
021
...
119
-99
120
...
145
neutral / no effect
146
...
244
1
245
...
255
full plusgreen
000
...
255
0
notes
...
-1
1
%
GN
(1)
%
GN
(1)
%
(2)
...
99
1
...
100
0.3922
-
5
hue
000
...
255
0
...
360
1.4118
°
6
saturation
000
...
255
0
...
100
0.3922
%
L7-C Mode 04 - RGBW 8 BIT
channel no.
function
DMX value
steps per bit
unit
1
master intensity
000
...
255
output value
0
...
100
0.3922
%
2
red intensity
000
...
255
0
...
100
0.3922
%
3
green intensity
000
...
255
0
...
100
0.3922
%
4
blue intensity
000
...
255
0
...
100
0.3922
%
5
white intensity
000
...
255
0
...
100
0.3922
%
steps per bit
unit
...
255
...
100
0.3922
%
notes
L7-C Mode 05 - HSI 8 BIT
channel no.
function
DMX value
1
intensity
000
output value
0
2
hue
000
...
255
0
...
360
1.4118
°
3
saturation
000
...
255
0
...
100
0.3922
%
notes
L7-C Mode 06 - White & RGBW 16 BIT
channel no
1
2
3
4
function
DMX value
master intensity
color temperature
5
HI
LO
HI
LO
HI
green / magenta
value
6
LO
7
HI
8
9
10
11
12
13
14
15
16
white-color
crossfade
red intensity
green intensity
blue intensity
white intensity
LO
HI
LO
HI
LO
HI
LO
HI
LO
output value
steps per bit
unit
00000
...
65535
0
...
100
0.001529
%
00000
...
65535
2,800
...
10,450
0.1167
K
00000
...
05000
neutral / no effect
05001
...
10000
full minusgreen
10001
...
29999
-99.995
30000
...
40000
neutral / no effect
40001
...
59999
0.005
60000
...
65535
full plusgreen
00000
...
65535
0
...
100
00000
...
65535
0
...
00000
...
65535
0
00000
...
65535
00000
...
65535
...
-0.005
...
99.995
0.005
% GN
(1)
% GN
(1)
0.001529
%
(2)
100
0.001529
%
...
100
0.001529
%
0
...
100
0.001529
%
0
...
100
0.001529
%
0.005
-
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
18
www.arri.com
notes
channel no
1
2
3
4
function
DMX value
HI
intensity
LO
color temperature
5
HI
LO
HI
green / magenta
value
6
LO
output value
steps per bit
unit
00000
...
65535
0
...
100
0.001529
%
00000
...
65535
2,800
...
10,450
0.1167
K
00000
...
05000
neutral / no effect
-
05001
...
10000
full minusgreen
-
10001
...
29999
-99.995
30000
...
40000
neutral / no effect
40001
...
59999
0.005
60000
...
65535
full plusgreen
...
-0.005
0.005
notes
% GN
(1)
% GN
(1)
ENGLISH
L7-C Mode 07 - White 16 BIT
...
99.995
0.005
-
L7-C Mode 08 - White & HSI 16 BIT
channel no
1
2
3
4
function
DMX value
master intensity
color temperature
5
HI
LO
HI
LO
HI
green / magenta
value
6
LO
7
HI
8
9
10
11
12
white-color
crossfade
LO
HI
hue
LO
saturation
HI
LO
output value
steps per bit
unit
00000
...
65535
0
...
100
0.001529
%
00000
...
65535
2,800
...
10,450
0.1167
K
00000
...
05000
neutral / no effect
-
05001
...
10000
full minusgreen
-
10001
...
29999
-99.995
30000
...
40000
neutral / no effect
40001
...
59999
0.005
60000
...
65535
full plusgreen
00000
...
65535
0
...
100
00000
...
65535
0
...
00000
...
65535
0
...
...
-0.005
0.005
notes
% GN
(1)
% GN
(1)
0.001529
%
(2)
360
0.005493
°
100
0.001529
%
steps per bit
unit
...
99.995
0.005
-
L7-C Mode 09 - RGBW 16 BIT
channel no
1
2
3
4
5
6
7
8
9
10
function
DMX value
master intensity
red intensity
green intensity
blue intensity
white intensity
HI
LO
HI
LO
HI
LO
HI
LO
HI
LO
output value
00000
...
65535
0
...
100
0.001529
%
00000
...
65535
0
...
100
0.001529
%
00000
...
65535
0
...
100
0.001529
%
00000
...
65535
0
...
100
0.001529
%
00000
...
65535
0
...
100
0.001529
%
notes
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
19
ENGLISH
L7-C Mode 10 - HSI 16 BIT
channel no
1
2
3
4
5
6
function
DMX value
HI
intensity
LO
HI
hue
LO
saturation
HI
LO
output value
steps per bit
unit
00000
...
65535
0
...
100
0.001529
%
00000
...
65535
0
...
360
0.005493
°
00000
...
65535
0
...
100
0.001529
%
notes
L7-C Mode 11 - White & RGBW C/F
channel no.
function
DMX value
steps per bit
unit
1
master intensity
000
...
255
0
...
100
0.3922
%
2
master intensity (fine)
000
...
255
0
...
10
0.0392
%
3
color temperature
000
...
255
2,800
...
10,450
30
K
4
color temperature (fine)
...
255
5
green / magenta value
output value
000
...
255
0
000
...
010
neutral / no effect
011
...
020
full minusgreen
021
...
119
-99
120
...
145
neutral / no effect
146
...
244
1
notes
K
-
...
-1
...
99
1
% GN
(1)
% GN
(1)
(2)
1
245
...
255
full plusgreen
6
white-color crossfade
000
...
255
0
...
100
0.3922
%
7
red intensity
000
...
255
0
...
100
0.3922
%
8
red intensity (fine)
000
...
255
0
...
10
0.0392
%
9
green intensity
000
...
255
0
...
100
0.3922
%
10
green intensity (fine)
000
...
255
0
...
10
0.0392
%
11
blue intensity
000
...
255
0
...
100
0.3922
%
12
blue intensity (fine)
000
...
255
0
...
10
0.0392
%
13
white intensity
000
...
255
0
...
100
0.3922
%
14
white intensity (fine)
000
...
255
0
...
10
0.0392
%
L7-C Mode 12 - White C/F
channel no.
function
DMX value
steps per bit
unit
1
intensity
000
...
255
0
...
100
0.3922
%
2
intensity (fine)
000
...
255
0
...
10
0.0392
%
3
color temperature
000
...
255
2,800
...
10,450
30
4
color temperature (fine)
000
...
255
0
...
255
000
...
010
neutral / no effect
-
011
...
020
full minusgreen
-
5
green / magenta value
output value
021
...
119
-99
120
...
145
neutral / no effect
146
...
244
1
245
...
255
full plusgreen
...
-1
20
K
K
1
% GN
(1)
% GN
(1)
...
99
1
-
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
notes
channel no.
function
DMX value
1
master intensity
000
...
255
0
...
2
master intensity (fine)
000
...
255
0
...
3
color temperature
000
...
255
2,800
4
color temperature (fine)
000
...
255
0
000
...
010
neutral / no effect
-
011
...
020
full minusgreen
-
021
...
119
-99
120
...
145
neutral / no effect
146
...
244
1
5
green / magenta value
output value
steps per bit
unit
100
0.3922
%
10
0.0392
%
...
10,450
30
K
...
255
1
K
...
-1
1
notes
% GN
(1)
% GN
(1)
(2)
ENGLISH
L7-C Mode 13 - White & HSI C/F
...
99
1
245
...
255
full plusgreen
6
white-color crossfade
000
...
255
0
...
100
0.3922
%
7
hue
000
...
255
0
...
360
1.4118
°
8
hue (fine)
000
...
255
0
...
25.5
0.100
°
9
saturation
000
...
255
0
...
100
0.3922
%
10
saturation (fine)
000
...
255
0
...
10
0.0392
%
L7-C Mode 14 - RGBW C/F
channel no.
function
DMX value
steps per bit
unit
1
master intensity
000
...
255
0
output value
...
100
0.3922
%
2
master intensity (fine)
000
...
255
0
...
10
0.0392
%
3
red intensity
000
...
255
0
...
100
0.3922
%
4
red intensity (fine)
000
...
255
0
...
10
0.0392
%
5
green intensity
000
...
255
0
...
100
0.3922
%
6
green intensity (fine)
000
...
255
0
...
10
0.0392
%
7
blue intensity
000
...
255
0
...
100
0.3922
%
8
blue intensity (fine)
000
...
255
0
...
10
0.0392
%
9
white intensity
000
...
255
0
...
100
0.3922
%
10
white intensity (fine)
000
...
255
0
...
10
0.0392
%
notes
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
21
ENGLISH
L7-C Mode 15 - HSI C/F
channel no.
function
DMX value
1
Intensität
000
output value
...
255
0
...
100
steps per bit
unit
0.3922
%
2
Intensität (fein)
000
...
255
0
...
10
0.0392
%
3
Farbton
000
...
255
0
...
360
1.4118
°
4
Farbton (fein)
000
...
255
0
...
25.5
0.100
°
5
Sättigung
000
...
255
0
...
100
0.3922
%
6
Sättigung (fein)
000
...
255
0
...
10
0.0392
%
notes
Remarks:
(1)
"%GN" means the percentage of shift between the neutral color point and the full minusgreen resp. full plusgreen color points derived from Rosco Cinegel gels #3304 resp. #3308.
(2)
"crossfade" means the percentage of shift from the programmed white color point to the programmed RGBW or HSI color point.
5.2.4 Conversion of CCT value to DMX %
You can convert the CCT value to DMX % (or the other way around) with the following formula:
CCT-value = (CCTmax - CCTmin) x (DMX-value in %) / (100 + CCTmin)
DMX-value in % = CCT-value - CCTmin) / (CCTmax - CCTmin) x 100
L7-C:
CCTmin = 2800
CCTmax = 10000
L7-TT:
CCTmin = 2600
CCTmax = 3600
L7-DT:
CCTmin = 5000
CCTmax = 6500
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
22
www.arri.com
RDM standard commands:
Command (English)
Description
GET
SET
Discover Unique Branch
Searches RDM device
yes
yes
Discover Mute
Mutes the RDM device, no response messages
yes
yes
Discover Unmute
Activates device for response messages
yes
yes
yes
Supported Parameters
Shows a list of all supported RDM commands
yes
Parameter Description
Shows a list of commands that are not standard
rdm commands, mostly commands from manufacturer. Describes the data type and shows if
Set or Get or both are supported for the listed
commands.
Lists RDM protocol version, device model ID,
product category, software version ID (from Main),
DMX footprint, DMX personality, sub-device count
and sender count
yes
Software Version Label
Shows the software version string from main, e.g.
Main 1.66.1 Yesn 16 2012 19:10:26
yes
DMX Start Adress
DMX address
yes
yes
Identify Device
Identify Flag -> physically flash the light,
L7-C flashes Blue and all other White
yes
yes
Status Message
Display of actual warning / error message of the
fixture
yes
Status ID Description
Detailed description of each warning / status
report
yes
yes
Device Label
This parameter allows you to generate an informative label for each fixture.
It can be utilized to identify the rack number of a
dimmer or to determine the position of a fixture
Product Detail ID List
This parameter is utilized to retrieve technical
details of a fixture.
L7 shows LED with PWM control
yes
Device Model Description
A text description of up to 32 characters for the
model type of the fixture.
L7 shows L7-C or L7-T
yes
Manufacturer Label
Display the company name ARRI Lighting
Boot Software Version ID
PrBo SW Version 2.03.00
yes
Boot Software Version Label
Shows text from PrBo Bootloader, e.g. PrBo
2.03.00 Jan 16 2012 19:10:26
yes
DMX Personality
DMX mode
yes
DMX Personality Description
Displays a text description of a DMX mode with up
to 32 characters, shown exactly as in the description in the LS-Manager
yes
Slot Info
Shows a description for each DMX channel in use
in the requested DMX mode
yes
Device Info
ENGLISH
The RDM functions listed below are supported from SW version 1.66.08
Required RDM command extensions
yes
yes
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
23
ENGLISH
Command (English)
Description
GET
Slot Description
Shows a text description with max. 32 characters
for each DMX channel from the requested DMX
mode
yes
Default Slot Value
Shows the default DMX channel value from the
requested DMX mode
yes
Sensor Definition
Shows the definition from a specific sensor and a
text description
yes
Sensor Value
Shows the actual sensor value
yes
Device Hours
Shows the actual device hours of the fixture
yes
Lamp Hours
Shows the actual lamp hours of the fixture
yes
Factory Defaults
This command deletes all user parameters and
sets the fixture to factory default
yes
Device Power Cycles
Shows the power cycle value, counts every cold
start (switch or power-up)
yes
Reset Device
Fixture makes a software reset (warm start) and
carries out a reboot
yes
yes
Power State
Power state of the fixture, supported power states:
POWER_STATE_STANDBY (0x02),
POWER_STATE_NORMAL (0xFF),
POWER_STATE_FULL_OFF (0x00)
POWER_STATE_SHUTDOWN (0x01)
yes
yes
Perform Selftest
Supported test modes and demo modes
yes
yes
Self Test Description
Shows a description for each test / demo mode
yes
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
24
www.arri.com
SET
yes
Command (English)
Description
RDM Fan Mode
Changes the FAN mode of the fixture
PID:0x8001
- this message supports Set and Get commands
- the first data byte is used to show / change the fan mode
GET
SET
yes
yes
ENGLISH
Manufacturer commands
hybrid:
USER_FAN_MODE_OFF
=0
USER_FAN_MODE_LOW
=1
USER_FAN_MODE_HIGH
=2
USER_FAN_MODE_AUTO_LOW = 3
USER_FAN_MODE_AUTO_HIGH = 4
USER_FAN_MODE_VARI = 5
USER_FAN_MODE_PASS = 6
active:
USER_FAN_MODE_LOW = 1
USER_FAN_MODE_VARI = 2
USER_FAN_MODE_HI45 = 3
RDM Status LED
Switch on /off indication LEDs and LCD back light
PID:0x8002
- this message supports Set and Get commands
- the first data byte is used to switch indication LEDs on and off
LEDs and LCD back light on = 0
LEDs and LCD back light off = 1
Supported values from -1 to +1
RDM DMX Signal Lost
Mode
PID:0x8005
If the DMX signal gets lost or the DMX device is unplugged the
LED fixture holds the last valid signal, or it holds the last valid signal for two minutes and then dimms or switches off immediately.
Supported values:
0 -> hold
1 -> hold 2 minutes
3 -> switch off
5.3 LSeries Manager
The LSManager software bundle which can be downloaded from the ARRI web site free of charge contains an instruction manual
for the LSManager software. Please find a detailed description of the functionality in this manual.
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
25
ENGLISH
6. Technical Data
Specifications of the L7 range
Optical system
focussable Fresnel
Lens diameter
175 mm / 7 Inch
Beam angle
15° - 50° (half peak angle)
Handling
Adjustable sliding stirrup, high strength tilt lock, pole operation optional (pan, tilt and focus)
Mounting
28 mm / 1,10 Inch spigot
Tilt angle
+/- 90°
Power supply range
90 - 264V AC, 50-60Hz
Replaceable fuse
2,5A flink “F“, breaking capacity: 1500A and 250V AC, size: 5x20 mm / 0,196x0,787 Inch
Power consumption
220 W maximum
Power connection
Bare ends / Schuko / Edison Connector
Dimming
0 -100% continuous
Control
5-Pin DMX „In and Through“, Optional on-board controller, Mini-USB
Remote Device Management (RDM)
DMX functions, hour counter and standard RDM commands
Mini-USB interface
DMX functions, fixture status and firmware upgrade through PC software
Housing colors
Blue-silver, black
Estimated LED lifetime (L70)
50,000 hours
Certifications
CE, GS, FCC, cNRTL, CB, ISO9001:2000
All specifications are nominal / typical values.
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
26
www.arri.com
Lamphead type
L7-C hybrid
L7-DT hybrid
L7-TT hybrid
L7-T hybrid
Weight
10.9 kg / 24 lb (hanging /
stand), 12.5 kg / 27 lb (pole
operation)
10.9 kg / 24 lb (hanging /
stand), 12.5 kg / 27 lb (pole
operation)
10.9 kg / 24 lb (hanging /
stand), 12.5 kg / 27 lb (pole
operation)
10.9 kg / 24 lb (hanging /
stand), 12.5 kg / 27 lb (pole
operation)
White light
Continuously variable correlated color temperature from
2,800 K - 10,000 K
Continuously variable correlated color temperature from
5000 K - 6500 K
Continuously variable correlated color temperature from
2600 K - 3600 K
Colored light
Full RGB+W gamut with hue
and saturation control
Color rendition
Green-Magenta adjustment
Ambient temperature opertion
3200 K
-
-
-
CRI 95 (3,200 K - 6,500 K)
CRI 94
CRI 92
-
+/- 1/8 (nominal)
+/- 1/8 (nominal)
+/- 1/8 (nominal)
+/- 1/8 (nominal)
-20° - 35° C / -4° - 95° F
-20° - 35° C / -4° - 95° F
-20° - 35° C / -4° - 95° F
-20° - 35° C / -4° - 95° F
IP 20
IP 20
IP 20
IP 20
Protection class
ENGLISH
Individual specifications
All specifications are nominal / typical values.
Individual specifications
Lamphead type
L7-C aktiv
L7-DT aktiv
L7-TT aktiv
L7-T aktiv
Weight
8.2 kg / 18 lb (hanging /
stand), 9.8 kg / 21.6 lb (pole
operation)
8.2 kg / 24 lb (hanging /
stand), 9.8 kg / 27 lb (pole
operation)
8.2 kg / 24 lb (hanging /
stand), 9.8 kg / 27 lb (pole
operation)
8.2 kg / 18 lb (hanging /
stand), 9.8 kg / 21.6 lb (pole
operation)
White light
Continuously variable correlated color temperature from
2,800 K - 10,000 K
Continuously variable correlated color temperature from
5000 K - 6500 K
Continuously variable correlated color temperature from
2600 K - 3600 K
Colored light
Full RGB+W gamut with hue
and saturation control
Color rendition
CRI 95 (3,200 K - 6,500 K)
Green-Magenta adjustment
Ambient temperature opertion
3200 K
-
-
-
CRI 94
CRI 92
-
+/- 1/8 (nominal)
+/- 1/8 (nominal)
+/- 1/8 (nominal)
+/- 1/8 (nominal)
-20° - 45° C / -4° - 113° F
-20° - 45° C / -4° - 113° F
-20° - 45° C / -4° - 113° F
-20° - 45° C / -4° - 113° F
IP 20
IP 20
IP 20
IP 20
Protection class
All specifications are nominal / typical values.
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
www.arri.com
27
ENGLISH
EC Declaration of Conformity
The designated products conform to the specifications of the following European directives:
· Directive 2014/30/EU of the European Parliament and the Council of 26 February 2014 on the
harmonisation of the laws of the Member States relating to electromagnetic compatibility
· Directive 2014/35/EU of the European Parliament and the Council of 26 February 2014 on
the harmonisation of the laws of the Member States relating to the making available on the
market of electrical equipment designed for use within certain voltage limits
· Directive 2011/65/EU of the European Parliament and the Council of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
Please visit our website if you should experience any technical problems.
You will also find a directory of our ARRI Service Centers there.
Visit our homepage for further information and to download our service tools.
www.arri.com
Arnold & Richter Cine Technik GmbH & Co. Betriebs KG, Pulvermühle, 83071 Stephanskirchen
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement