Digiplex DGP2-641BL Operating instructions

Digiplex DGP2-641BL Operating instructions
LCD Keypad Module
DGP2-641
System Manager’s Manual
Also includes
Operating Instructions
TABLE OF CONTENTS
INTRODUCTION ........................................................... 5
Legend.......................................................................................... 5
BASIC OPERATION .....................................................
Auditory Feedback (Beep Tones) ................................................
Confidential Mode .......................................................................
Partitioned System .......................................................................
Area Status Display......................................................................
5
5
6
6
6
ARMING ........................................................................
Exit Delay Timer..........................................................................
Regular Arming............................................................................
Stay Arming .................................................................................
Instant Arming .............................................................................
Force Arming ...............................................................................
Bypass Programming ...................................................................
One-Touch Buttons ......................................................................
Keyswitch Arming .......................................................................
Auto-Arming ................................................................................
6
6
6
7
7
7
7
8
8
8
DISARMING ..................................................................
Entry Delay Timer........................................................................
Disarming an Armed System .......................................................
Alarm Memory Display ...............................................................
8
8
9
9
ACCESS CODES .......................................................... 9
System Master Code (Default 123456)........................................ 9
User Labels................................................................................. 10
Deleting User Access Codes ...................................................... 11
Programming User Access Codes.............................................. 12
User Options............................................................................... 14
Access Control User Options ..................................................... 14
Standard Fire Zone .....................................................................
Delayed Fire Zone ......................................................................
Fire Safety Tips ..........................................................................
Minimizing Home Fire Hazards.................................................
Home Fire Warning System .......................................................
Burglar Alarm.............................................................................
20
20
21
21
21
21
VOICE-ASSISTED ARM/DISARM MODULE
INTRODUCTION ......................................................... 22
ACCESS CODES ........................................................ 22
HOW DO I USE IT? ..................................................... 22
THINGS YOU SHOULD KNOW .................................. 22
22
22
22
23
When Accessing your InTouch... ...............................................
When Arming or Disarming.......................................................
When Activating or Deactivating a PGM... ...............................
When Using your Intouch... .......................................................
TELEPHONE BUTTON FEATURES........................... 23
INTOUCH EXAMPLE .................................................. 23
INTOUCH SYSTEM CHECKLIST ............................... 24
APPENDIX 1: HEBREW SPECIAL CHARACTERS... 25
APPENDIX 2: RUSSIAN SPECIAL CHARACTERS .. 26
INDEX .......................................................................... 28
USING ACCESS CONTROL ....................................... 15
Entering & Exiting ..................................................................... 15
Arming and Disarming with Card.............................................. 15
How Access Control Works....................................................... 16
TROUBLE DISPLAY ................................................... 17
Event Record Display ................................................................ 17
ADDITIONAL FEATURES........................................... 18
Programmable Outputs (PGMs)................................................. 18
Keypad Settings ......................................................................... 18
Set Time & Date......................................................................... 18
Programming Chime Zones ....................................................... 19
Panic Alarms .............................................................................. 19
Quick Function Buttons ............................................................. 19
TESTING AND MAINTENANCE ................................. 19
Burglar Alarm Testing ............................................................... 19
Fire Alarm Testing ..................................................................... 19
System Maintenance .................................................................. 20
System Test ................................................................................ 20
FIRE AND BURGLAR ALARMS................................. 20
LCD Keypad
© 2002-2003 Paradox Security Systems Ltd.
Digiplex, InTouch and WinLoad are trademarks or registered trademarks of Paradox Security Systems Ltd. or its affiliates in
Canada, the United States and/or other countries. All rights reserved. Specifications may change without prior notice.
4 System Manager’s Manual
1.0 INTRODUCTION
Your Digiplex Security System is an advanced technology security system that will provide you with reliable security
protection and powerful features that are easy to use. The elegant and user-friendly LCD keypad will allow you easy
access to your security system's functions and information at the touch of a button. The 32-character LCD screen
will display messages and menus to guide you through the system’s operations. Your Installer can even customize
the messages for your home or business.
Since you will communicate your instructions to your system through the keypad, please read this manual carefully
and have your Installer explain basic system operation.
If you have the InTouch Voice Assisted Arm/Disarm Module (APR3-ADM2) connected to your Digiplex security
system, please refer to page 22 for operating instructions.
1.1
LEGEND
Indicates a warning or an important note.
Indicates useful information or a tip.
[SQUARE BRACKETS] Indicates information that must be entered on the keypad.
2.0 BASIC OPERATION
The following sections will introduce you to the roles of the buttons, lights, and messages on your LCD keypad.
Figure 2.1: Basic Overview
The LCD screen will guide you
with detailed messages.
“AC” LIGHT:
ON = AC power
OFF = Power failure
“STATUS” LIGHT:
When Green:
ON = All zones are closed.
OFF = One or more zones are open.
FLASH = Exit Delay
When Red:
ON = Area(s) armed
OFF = Area(s) disarmed
FLASH = System in Alarm
Use the arrow buttons to scroll
through the current menu when
the arrows appear in the LCD
screen.
ACTION BUTTONS:
Each button’s function is explained in the following sections of the manual.
[CLEAR] = Erases current data entry
or reverts to the preceding step.
2.1
[ENTER] = Saves current data and
exits current menu.
AUDITORY FEEDBACK (BEEP TONES)
When you enter information on the keypad, the keypad will guide you with beep tones to communicate the
acceptance or rejection of your entries.
Confirmation Beep: When an operation (i.e. arming/disarming) is successfully entered or when the system
switches to a new status/mode, the keypad emits an intermittent beep tone (“BEEP-BEEP-BEEP-BEEP-BEEP”).
Rejection Beep: When the system reverts to a previous status, or when an operation is incorrectly entered, the
keypad emits a continuous beep tone (“BEEEEEEEEEEP”).
LCD Keypad 5
2.2
CONFIDENTIAL MODE
Your Installer can program keypads to not display the status of your system automatically by changing the LCD
screen to Confidential Mode. In Confidential Mode:
• The zones and status messages will NOT be displayed
• The indicator lights will NOT illuminate
• Depending on how your keypad was programmed by your installer, you must either press a button or enter your User
Access Code to illuminate the indicator lights and activate Normal Mode.
2.3
PARTITIONED SYSTEM
A separated system is called a Partitioned System, which can be useful in situations where shared security systems
are more practical. Your installer can design your system to recognize up to four separate protected areas. For
example, a company that has both an office area and a warehouse area can arm and disarm each area separately
and control the access to each area.
If you have access to more than one area, and you need to select a specific area(s) when prompted by your LCD
keypad, follow either one of the following three methods to make your selection:
• Press the keypad button corresponding to the area you wish to select (i.e. 1, 2,...4).
• Press the [0] button for all areas.
• Use the [S] and [T] buttons, and press [ENTER] when the area you want to select appears on the screen.
2.4
AREA STATUS DISPLAY
The Area Status Display
allows you to view the status
of the selected areas in a
Partitioned System (Refer to
section 2.3 on page 6).
How do I see the status of the areas?
1) Enter your [ACCESS CODE], then press the [1] button.
2) Press the button corresponding to the area (i.e. 1, 2,...4), or use the [S] and
[T] buttons and press [ENTER] when the area you want to view appears on
the screen.
3) Press [CLEAR] to exit.
In Area Status Display mode, the following information will scroll on the LCD screen:
•
•
•
•
•
•
“ready”: if all zones in the selected area are closed.
“not ready”: if zones in the selected area are open.
open zones within that area (i.e. “Front Door Open”).
“Trouble(s)”: (section 7.0 on page 17) if a trouble has occurred.
“Alarms in Memory”: (section 4.3 on page 9) if an alarm has occurred.
“Armed” ; “Force Armed” ; “Instant Armed” ; “Stay Armed”: displays the arming status of the selected area.
3.0 ARMING
When your system is armed, it can respond to any breach in the protected zones by causing an alarm and sending
a report to your Central Monitoring Station.
3.1
3.2
EXIT DELAY TIMER
When you arm your system, it will trigger the Exit Delay Timer to provide you with enough time to exit the protected
area before the system is armed.
REGULAR ARMING
This method is used for the
everyday arming of your
system. All zones within the
protected area must be
closed to Regular arm the
system.
6 System Manager’s Manual
How do I Regular arm the system?
1) Enter your [ACCESS CODE].
2) Press the [ARM] button.
3) If you have access to more than one area, select the area(s) you wish to
Regular arm (refer to section 2.3 on page 6).
3.3
STAY ARMING
Stay arming will partially arm
your system to permit you to
remain in your home or office
by arming the outer zones
(perimeter) of the protected
area
(i.e.
doors
and
windows).
3.4
3.5
INSTANT ARMING
This feature is the same as
Stay arming except that there
is no Entry Delay. Therefore,
any armed zone that is
breached will immediately
generate an alarm.
2) Press the [STAY] button.
3) If you have access to more than one area, select the area(s) you wish to
Stay arm (refer to section 2.3 on page 6).
How do I Instant arm?
1) Enter your [ACCESS CODE].
2) Press the [5] button.
3) If you have access to more than one area, select the area(s) you wish to
Instant arm (refer to section 2.3 on page 6).
FORCE ARMING
Force arming allows you to
quickly arm your system
when zones are open.
However, once the open zone
is closed, your system will
then arm that zone as well.
3.6
How do I Stay arm?
1) Enter your [ACCESS CODE].
How do I Force arm?
1) Enter your [ACCESS CODE].
2) Press the [FORCE] button.
3) If you have access to more than one area, select the area(s) you wish to
Force arm (refer to section 2.3 on page 6).
BYPASS PROGRAMMING
You can bypass certain zones
when you arm the protected
area(s). When a zone is
bypassed, it will be ignored
the next time your system is
armed. Once your area is
disarmed, the system will
unbypass the zone.
How do I Bypass a zone?
1) Enter your [ACCESS CODE].
2) Press the [BYP] button.
3) Enter the zone number (i.e. 01, 02,...48), or use the [S] and [T] buttons and
press [BYP] once the zone you want to bypass appears on the screen. If
“bypassed” does not appear on the screen and the keypad emits a Rejection
Beep, you may not have access to bypass that zone.
4) Repeat step 3 until all zones you want to bypass have been selected.
5) Press the [ENTER] button to save and exit.
In order to bypass a zone, the following conditions must be met:
- The zone must have the Bypass option programmed by the installer.
- Your User Access Code must be programmed to enable the Bypass option.
- Your User Access Code must have access to the zone’s Area Assignment.
- The zone’s area must be disarmed before the zone can be bypassed.
Fire Zones cannot be bypassed.
3.6.1
BYPASS RECALL
Bypass Recall reinstates the
zones that were bypassed the
last time your system was
armed.
How do I activate Bypass Recall?
1) Enter your [ACCESS CODE].
2) Press the [BYP] button.
3) Press the [MEM] button.
Zones bypassed the last time your system was armed are bypassed.
4) Press the [ENTER] button to save and exit.
LCD Keypad 7
3.7
3.8
3.9
ONE-TOUCH BUTTONS
If enabled by your Installer, you can access the following features without using your User Access Code by pressing
and holding the desired One-Touch button.
BUTTON
FEATURE
BUTTON
FEATURE
[ARM]
Regular arm
[DISARM]
Disarm a Stay/Instant armed area
[STAY]
Stay arm
[5]
Instant arm
[FORCE]
Force arm
[6]
Change display settings
[BYP]
Bypass Programming
[7]
View Event Record display
KEYSWITCH ARMING
A key can be used to arm and disarm your system using two forms of keyswitches. With a Maintained Keyswitch,
place the key in the “ON” position to arm your system, and place the key in the “OFF” position to disarm your
system. With a Momentary Keyswitch, place the key in the “ON” position briefly then place it back in the “OFF”
position to arm the system. Repeat this process to disarm with a Momentary Keyswitch.
AUTO-ARMING
If enabled by your Installer, you can set the time that an area will arm itself automatically.
3.9.1
TIMED AUTO-ARMING
Your installer can set Timed
Auto-Arming to function in
either Force or Stay arming
mode. A sixty-second Exit
Delay sequence will begin
prior
to
your
system
automatically arming itself at
the programmed time.
How do I set the Auto-Arming timer?
1) Enter your [ACCESS CODE].
2) Press the [0] button.
3) Press the [MEM] button.
4) If you have access to more than one area, press the area’s number, or use
the [S] and [T] buttons and press the [ACC] button when the area you want
to program appears on the screen.
5) Enter the time you want the area to be armed according to the 24-hour clock
(i.e. 9 a.m. is 09:00 and 9 p.m. is 21:00).
6) Press the [ENTER] button to save and exit.
3.9.2
NO MOVEMENT AUTO-ARMING
Your system can be programmed to send a report to your Central Monitoring Station and/or arm the system if there
is no activity in the area during a specified period of time. Your installer can set No Movement Auto-Arming to
function in either Regular or Stay arming mode.
4.0 DISARMING
When your system is disarmed, it deactivates any alarms in progress, and it deactivates the zones so the alarm will
not be triggered if zones are breached.
4.1
ENTRY DELAY TIMER
Your installer will program designated entry points (i.e. the front door) with an Entry Delay Timer. This delay gives
you time to enter the armed premises and enter your code to disarm your system before the alarm is triggered.
8 System Manager’s Manual
4.2
DISARMING AN ARMED SYSTEM
How do I disarm the system?
1) Enter your [ACCESS CODE].
2) Press the [DISARM] button.
If you have access to more than one area, select the area(s) you wish to
disarm (refer to section 2.3 on page 6).
You can only disarm an area
to which your User Access
Code is assigned. User
Access Codes with the “Arm
Only” (section 5.5 on page
14) option enabled cannot
disarm an armed system.
How do I disarm a system in alarm?
1) Enter your [ACCESS CODE].
2) In the case of a false alarm, call your Central Monitoring Station quickly to
advise them of the false alarm.
In the case of a burglar alarm, leave the premises and call the Police from a safe place.
4.3
ALARM MEMORY DISPLAY
How do I view the list of alarms that occurred?
When an alarm has occurred, the LCD screen will display “Alarms in Memory
[MEM] to View”.
1) Press the [MEM] button. Each zone that was breached while armed will
appear below “Alarm in:”.
2) Press the [CLEAR] button to exit the Alarm Memory Display.
Your system will record all the
alarms that occurred during
the last armed period. The
zones in alarm will remain in
the Alarm Memory until the
next time that area is armed.
5.0 ACCESS CODES
Access Codes allow access to the system. Your system supports up to 96 User Access Codes. Codes are given a
User Number between 02 and 96 (User Number 01 is the System Master Code). Your Installer will program User
Access Codes to be four, six, or variables of one to six digits in length. Each digit can be any value between zero
and nine. If your Installer programmed your system to accept a variable code length, you have to press the [ENTER]
button after entering your User Access Code.
5.1
SYSTEM MASTER CODE (Default 123456)
The System Master Code will How do I change the System Master Code?
give you access to all the 1) Enter the current [SYSTEM MASTER CODE] (default: 123456).
features available on your
2) Press the [0] button.
system, as well as the ability
to add, modify, or delete any 3) Press the [ACC] button.
User Access Codes. We 4) Enter the number [01].
suggest that you change this 5) Enter a [NEW CODE].
code to prevent others from 6) Press the [ENTER] button to save and exit.
accessing
and
changing
options without authorization. Your Installer can set The System Master Code to be either 4 or 6 digits in length.
The System Master Code has access to all Access Control Doors and all Access Control
features at all times. Only the card’s serial number and the choice of arming method can be
changed. If the other options are manually changed, the System Master Code will immediately
revert to its original programming.
LCD Keypad 9
5.2
USER LABELS
User labels personalize User
Access Codes and can be
assigned by pressing [ENTER]
at any point after step 4
during the programming of
User Access Codes (Figure
5.1 on page 12). For
Example, the LCD keypad
can display “John Smith”.
5.2.1
How do I program a user label?
At any point after step 4 in Figure 5.1 on page 12:
1) Press the [ENTER] button.
2) Type the desired characters as detailed in section 5.2.1 on page 10 and
section 5.2.2 on page 10.
3) Press the [S] button to move the cursor to a new space.
4) Repeat steps 2 and 3 until the desired label is complete.
5) Press the [ENTER] button to save and exit.
KEYPAD BUTTONS
Every numeric button on your LCD keypad is assigned a set of characters. To obtain the desired character
using the numeric buttons on your keypad, press the corresponding button until the desired character
appears on the screen. For example, if you want to enter the character “C”, press the [1] button three
times (refer to Table 1 on page 10). If using a Hebrew keypad, refer to Table 4 in Appendix 1: Hebrew
Special Characters on page 25. If using a Russian keypad, refer to Table 6 in Appendix 2: Russian
Special Characters on page 26.
Table 1: Keypad Letter Assignment
Key
5.2.2
Press Key
Once
Press Key
Twice
Press Key
Three Times
[1]
A
B
C
[2]
D
E
F
[3]
G
H
I
[4]
J
K
L
[5]
M
N
O
[6]
P
Q
R
[7]
S
T
U
[8]
V
W
X
[9]
Y
Z
SPECIAL FUNCTION KEYS
[STAY] = Insert Space
Pressing the [STAY] key inserts a blank space in the current cursor position.
[FORCE] = Delete
Pressing the [FORCE] key will delete the character or blank space found at the current cursor position.
[ARM] = Delete Until the End
Pressing the [ARM] key will delete all characters and spaces to the right of the cursor and at the cursor's
position.
[DISARM] = Numeric Keys / Alphanumeric Keys
Every time the [DISARM] key is pressed it will toggle from numeric keys to alphanumeric keys and vice
versa. Numeric: Keys [0] to [9] represent numbers 0 to 9.
[BYP] = Lower Case / Upper Case
Every time the [BYP] key is pressed it will toggle the case setting from lower to upper case and vice versa.
[MEM] = Special Characters
After pressing the [MEM] key, the cursor will turn into a flashing black square. Using Table 2 on page 11,
enter the 3-digit number that represents the desired symbol. If using a Hebrew keypad, refer to Table 5 in
Appendix 1: Hebrew Special Characters on page 25. If using a Russian keypad, refer to Table 7 in
Appendix 2: Russian Special Characters on page 26.
10 System Manager’s Manual
Table 2: Special Characters Catalogue
5.3
DELETING USER ACCESS CODES
To delete User Access Codes, follow steps 1 to 5 in Figure 5.1 on page 12, but press the [CLEAR] button in step 5.
Once the information is erased, press the [ENTER] button to save and exit.
LCD Keypad 11
5.4
PROGRAMMING USER ACCESS CODES
The System Master and Users with the Master feature can program User Access Codes with User Options and
Area Assignments. Figure 5.1 on page 12 describes the steps you would follow to program User Access Codes.
If the keypad emits a Rejection Beep at any point during the programming procedure, you may have chosen an
existing User Code or you do not have access to certain User Options (section 5.5) and Area Assignments (step 7
in Figure 5.1 on page 12). User’s with the Master feature can only assign User Options and Area Assignments that
they are assigned to. For example, if a User with the Master feature is assigned User Option 1 and Area 2, they can
only assign Options 1 and Area 2 to a User Access Code.
Figure 5.1: Programming User Access Codes
Enter your [ACCESS CODE] (System Master Code or User Access Code with Master
feature).
Press [0] to enter the Programming Menu.
From Programming Menu, press [ACC].
Enter the 2-digit User Number you want to program; press the [T] button to scroll the
list of codes then press [ACC] once the desired code appears on the screen.
Enter a User Code within the brackets. Press the [S] button to reach the User Options
screen.
NOTE: The User Code is a Personal Identification Number (P.I.N.).
Program the User Options by pressing the number on your keypad corresponding to
the User Option you wish to enable. The option is considered ON when the number
appears within the brackets. Proceed to step 7 by pressing the [S] button. For a
detailed description of the User Options refer to section 5.5 on page 14.
Option [3]: Duress
Options [1] and [2] : Master Feature
Option
[4]: Bypass
[1] OFF = Master Feature disabled.
[1] ON, [2] OFF = User can only modify User Option [5]: Arm Only
Option [6]: Stay and Instant Arm
Access Codes.
Option
[7]: Force Arm
[1] ON, [2] ON = User has full Master rights.
Option
[8]: OFF - Access keypad’s
User can create, modify, and program User
partitions only
options, User Access Options and Area
ON - Access any
Assignments.
partition assigned
to user
12 System Manager’s Manual
Users are able to perform actions (arming, disarming, etc.) only in the area(s) they are
assigned. To assign an area(s) to a User Access Code, enter the number corresponding
to the area you wish to assign (i.e. [1] = area 1, ...[4] = area 4).
Press the [T] button to return to the User Options; press the [S] button to proceed to
step 8; or press the [ENTER] button to save and exit programming mode.
NOTE: If no area is assigned, and if PGMs are programmed by your Installer, the User
can only control the PGMs. Refer to section 8.1 on page 18 for a more detailed
explanation of PGMs.
A) Enter the 2-digit Access Level (i.e. 00, 01,...15) within the first set of brackets.
An Access Level determines which Access Control Doors a User is allowed to pass
through. There are 16 possible Access Levels which are usually programmed by your
Installer. Access to all Access Control Doors is Access Level 00.
B) Enter the 2-digit Schedule (i.e. 00, 01,...15) in the second set of brackets.
Schedules, programmed by your Installer, determine the hours, days, and holidays that
Users are permitted through Access Control Doors. Each user is assigned a Schedule
through the User Access Code. To provide access at all times, assign Schedule 00.
Program the Access Control User Options by pressing the number on your keypad that
corresponds to the Option you wish to assign. The option is considered ON when the
number appears within the brackets. For a detailed description of the User Access
Control Options, refer to section 5.6 on page 14. Press the [S] button to proceed to step
10.
Option [1] : Access Card is Activated
Option [2] : Can Disarm with Access Card
Option [3] : Extended Unlocked Period
Options [4], [5], [6] & [7] : Arming with Card
Option [4] OFF = Disable the Arming with Card feature
Option [4] ON, options [5], [6] & [7] OFF = Regular Arm
Options [4] & [5] ON, options [6] & [7] OFF = Stay Arm
Options [4] & [6] ON, options [5] & [7] OFF = Instant Arm
Options [4] & [7] ON, options [5] & [6] OFF = Force Arm
Option [8] : Access to Armed Access Control Doors
Enter the Access Control Card’s serial number within the brackets.
Press the [ENTER] button to save and exit.
LCD Keypad 13
5.5
USER OPTIONS
Options [1] and [2]: Master Feature
When option [1] is OFF, the User cannot program other Users into the system.
When option [1] is ON and option [2] is OFF, the User can only modify existing User Access Codes.
When both options [1] and [2] are ON, the User has Full Master rights. The User can create or modify User
Access Codes, User Options, User Access Control Options, Access Card Numbers and Area Assignments
according to their own programming. For example, if the Full Master User has access to area #1 and option [4]
(Bypass) only, the Full Master User can only assign area #1 and option [4] to other Users in the system.
Option [3]: Duress
When option [3] is ON, the Duress feature is enabled. This feature is used when someone forces a User to arm
or disarm an area(s). By entering a User Access Code (P.I.N.) reserved for the Duress feature, the system will
arm or disarm the area(s), and then send a silent alarm to the Central Monitoring Station.
Option [4]: Bypass
When option [4] is ON, the Bypass feature is enabled. This feature allows the User to deactivate zones when
arming the area(s).
Option [5]: Arm Only
When option [5] is ON, the Arm Only feature is enabled. The User can arm assigned areas with either a card or
code, but cannot disarm. When the option is OFF, the User can either arm or disarm assigned areas.
Option [6]: Stay & Instant Arm
When option [6] is ON, the Stay and Instant Arm features are enabled. The User can now Stay or Instant Arm
their assigned areas.
Option [7]: Force Arm
When option [7] is ON, the Force arm feature is enabled. The User can now Force arm their assigned areas.
Option [8]: Area Access
When option [8] is ON, the keypad will permit access to all the areas assigned to the User Access Code. When
option [8] is OFF, the keypad will only permit access to the areas it controls. For example, the keypad is
assigned area 1 only, and your User Access Code is assigned areas 1 to 4. If the option is ON, you can access
all four areas from the keypad. If the option is OFF, you can only access area 1.
By default all Users can Regular arm the system.
5.6
ACCESS CONTROL USER OPTIONS
Option [1]: Access Card is Activated
When option [1] is ON, the Access Control Card is activated and can be used when Access Control is enabled
in the system. When the option is OFF, the Access Control Card cannot be used.
Option [2]: Disarming with Access Card
When option [2] is ON, a User’s Access Control Card can unlock and disarm an armed Access Control Door
(see section 6.2.2 on page 15).
For option [2] to function in the ON position, option [5] “Arm Only” in the User Options
must be disabled (refer to section 5.5 on page 14).
Option [3]: Card with Extended Unlocked Period
When option [3] is ON, “Extended Unlocked Period” is enabled. “Extended Unlocked Period” refers to the time
period programmed into each Access Control Door by your Installer that extends the unlocked time of the door.
For example, if your Installer sets the Unlocked period of the door to 30 seconds and the Extended Unlocked
Period to 15 seconds, then a User Access Code with “Extended Unlocked Period” enabled will have a total of
45 seconds to pass through the door.
Options [4] to [7]: Arming with Card
Options [4] to [7] define the type of arming when arming with an Access Control Card (refer to section 6.2.1 on
page 15). You can either Regular arm, Stay arm, Instant arm, or Force arm.
[4] ON, [5] to [7] OFF = Regular Arm
[4] & [5] ON, [6] & [7] OFF = Stay Arm
[4] & [6] ON, [5] & [7] OFF = Instant Arm
[4] & [7] ON, [5] & [6] OFF = Force Arm
14 System Manager’s Manual
Option [8]: Access to Armed Access Control Doors
When option [8] is enabled, the Access Control Card can be used to open an armed Access Control Door. When a
valid Access Control Card is presented to a reader that is assigned to a zone and the zone is armed, access will be
granted and the Entry Delay will begin. When option [8] is ON, extra security is provided since a user must enter a
User Access Code to disarm the area.
For option [8] to function in the ON position, option [5] “Arm Only” in the User Options (refer
to section 5.5 on page 14) and option [2] “ Disarming with Access Card” in the Access Control
User Options (refer to section 5.6 on page 14) must be disabled.
6.0 USING ACCESS CONTROL
6.1
ENTERING & EXITING
Depending on how your system is installed, there are various ways to enter and exit Access Control Doors:
1) Present your Access Control Card to the reader. The system will verify that the card
is allowed access according to its assigned Access Level and Schedule. If it is
accepted, the system will unlock the door. The reader’s light can be programmed by
the installer to turn green or extinguish briefly to indicate that the door can be
opened. The reader can also be programmed by the installer to audibly inform you
that the door can be opened.
2) When the motion detector detects movement (Request for Exit), it will unlock the
door to permit passage from inside.
3) Enter your User Access Code on a keypad and press [ACC].
4) If the Access Control Door is on a “Door Unlocked Schedule”, you may be able to
open Access Control Doors without using a User Access Code or an Access Control
Card. Depending on the door’s programming, the door can remain unlocked during
the entire programmed schedule or the door can unlock once a valid Access Control
Card is presented to the reader during the schedule and then will remain unlocked
for the remainder of the schedule.
6.2
ARMING AND DISARMING WITH CARD
6.2.1
ARMING WITH CARD
An Access Control Card can be programmed to arm areas assigned to the door when it is presented to
the reader (door) twice within approximately 5 seconds without opening the door.
The Access Control card must be:
•
•
•
•
6.2.2
presented to a door during its assigned Schedule (refer to step 8 in Figure 5.1 on page 12).
presented to a door within its assigned Access Level (refer to step 8 in Figure 5.1 on page 12).
programmed to allow arming (options [4] and [5] in section 5.6 on page 14).
assigned to all areas that are assigned to the Access Control Door (refer to step 7 in Figure 5.1 on page
12), or assigned to at least one of the areas assigned to the Access Control Door depending on how
your Installer has programmed the Access Control Door.
DISARMING WITH CARD
To disarm and unlock an Access Control Door when the area assigned to it is armed, present your Access
Control Card to the reader (door).
The Access Control card must be:
•
•
•
•
presented to a door during its assigned Schedule (refer to step 8 in Figure 5.1 on page 12).
presented to a door within its assigned Access Level (refer to step 8 in Figure 5.1 on page 12).
programmed to allow disarming (option [2] in section 5.6 on page 14).
assigned to all areas that are assigned to the Access Control Door (refer to step 7 in Figure 5.1 on page
12), or assigned to at least one of the areas assigned to the Access Control Door depending on how
your Installer has programmed the Access Control Door.‘
LCD Keypad 15
6.3
HOW ACCESS CONTROL WORKS
To illustrate how Access Control functions, we will use three simple Access Control System examples:
Figure 6.1: Example A
Bonnie’s Access Control Card is
programmed with Access Level
01 and Schedule 01. If she
presents her card to the reader
on Door 02 on Tuesday, August
3 at 3 p.m., she will gain access
to the room.
Figure 6.2: Example B
If Bonnie presents her card to the
reader on Door 02 on Saturday
or on a Holiday at 3 p.m., she will
be denied access.
Figure 6.3: Example C
If we change Bonnie’s Access
Level to 02 and she presents her
card to the reader on Door 02 on
Tuesday, August 3 at 3 p.m., she
will be denied access.
16 System Manager’s Manual
7.0 TROUBLE DISPLAY
If your system experiences any
How do I view the Trouble Display?
problems, “Trouble(s) [TRBL] to
1) Press the [TRBL] button when “Trouble(s) [TRBL] to View” appears on the
View” will appear on the LCD
LCD screen. The Group Heading with the trouble will appear on the screen.
screen. The Trouble Display will
only display the troubles that 2) Press the [S] and [T] buttons to scroll between the Groups experiencing a
trouble.
occur in the area(s) to which the
keypad has been assigned. 3) Press the [NUMBER] of the Trouble you wish to view.
Potential troubles have been
sorted into eight groups. Only the troubles which are relevant to you are listed and described below. If a trouble that is
not described or listed below appears, contact your Installer.
We strongly suggest that if any troubles occur, contact your Installer immediately to have your
system serviced.
7.0.1
GROUP 1: SYSTEM
AC Failure
The control panel has detected a power failure. This means that your system is running on the backup
battery. If this trouble occurs when your establishment is not experiencing a power failure, call your
Installer for repairs.
Battery Trouble
The backup battery is disconnected, needs to be recharged, or replaced.
Bell Absent
The system has detected that the bell or siren is not connected.
7.1
7.0.2
GROUP 5: ZONE TAMPER
The zone(s) that was tampered with will be displayed on the LCD screen.
7.0.3
GROUP 6: ZONE LOW BATTERY
If a wireless device's battery needs to be replaced, the zone that is assigned to the device will be
displayed on the LCD screen.
7.0.4
GROUP 7: ZONE FAULT
A wireless device is no longer communicating with its receiver, or a connection or CleanMeTM trouble is
occurring with your smoke detectors.
7.0.5
GROUP 8: CLOCK LOSS
The time and date have been reset to the default. This is the only trouble that we recommend that you
correct. “Clock Loss [8] to Set” will appear on the LCD screen after you press the [TRBL] button. Refer to
section 8.3 on page 18 to set the time and date.
EVENT RECORD DISPLAY
How do I view the Event Record?
1) Enter your [ACCESS CODE].
2) Press the [7] button.
3) If you have access to more than one area, select the area(s) you wish to
view (refer to section 2.3 on page 6).
4) Use the [S] and [T] buttons to scroll between the events.
5) Press the [CLEAR] button to exit.
The Event Record Display will
record
the
user-initiated
actions that occurred in your
system as well as any alarms
or troubles (i.e. “Access
Granted”). You will only be
able to view the events that
occurred in the area(s)
assigned to your User Access
Code.
Once you have entered Event Record Display mode, you can change the order that the Event Record screens
appear by pressing the [7] button. If you already know the number of the event you want to view, press the [MEM]
button after step 3 above, and then enter the event's number.
LCD Keypad 17
8.0 ADDITIONAL FEATURES
8.1
PROGRAMMABLE OUTPUTS (PGMS)
Your system includes Programmable Outputs (PGMs) that can be programmed by your Installer. A PGM triggers
when a predetermined event or series of events occurs in your system. The PGMs can be programmed to reset
smoke alarms, turn on light switches, open or close garage doors and much more. Ask your Installer about this
useful feature.
8.2
KEYPAD SETTINGS
You can modify the keypad settings to suit your needs (Refer to Figure 8.1 on page 18).
1) Scrolling Speed refers to the amount of time that a message will remain on the screen before moving to the next
message.
2) Backlight refers to the illumination behind the buttons and LCD screen.
3) Contrast refers to how dark or pale characters will appear on the screen.
Figure 8.1: : Modifying LCD screen settings
8.3
SET TIME & DATE
How do I reset the time and date?
1) Enter your [ACCESS CODE] and press the [TRBL] button.
2) Press the [8] button.
3) To change the time, place the cursor under the number you want to change
by using the [S] button and enter the time according to a 24-hour clock (i.e.
9 a.m. is 09:00 and 9 p.m. is 21:00).
4) To change the date, place the cursor under the number you want to change
and enter the correct date according to year/month/day.
5) Press the [ENTER] button to save and exit.
18 System Manager’s Manual
8.4
PROGRAMMING CHIME ZONES
How do I program chime zones?
1) Enter your [ACCESS CODE].
2) Press the [9] button.
3) Press the [1] button to chime a zone. Then enter the
number corresponding to the zone to be chimed, or use
the [S] and [T] buttons to scroll the list of zones. Press
the [ACC] button to chime or unchime the zone that
appears on the screen. Press [ENTER] to save.
OR
Press the [2] button to set the time period a chimed zone
will beep. Enter the time that the chimed zone(s) will start
beeping when opened (HH:MM). Enter the time that the
chimed zone(s) will stop beeping when opened (HH:MM).
4) Press [CLEAR] to exit chime programming.
You can program the keypad
to emit a rapid, intermittent
beep
tone
whenever
designated zones are opened
or only when opened between
certain hours. These zones
are referred to as Chime
Zones. Your installer can also
program your Chime zones to
beep upon closure.
8.5
PANIC ALARMS
Your system can be programmed to send an alarm to your Central Monitoring Station to request help from the
police, a medical facility, the fire department, or anyone you wish when you press a pre-determined combination of
buttons. To generate a panic alarm, simultaneously press and hold the button combinations displayed in Table 3 on
page 19. Your installer can program the alarm to be either silent or audible.
Table 3: Panic Buttons
Panic Alarm Types
8.6
Buttons to be pressed and held
simultaneously
Emergency Panic
Press & hold the [1] and [3] buttons
Auxiliary Panic
Press & hold the [4] and [6] buttons
Fire Panic
Press & hold the [7] and [9] buttons
QUICK FUNCTION BUTTONS
How do I access the Quick Function Buttons?
1) Enter your [ACCESS CODE]
2) Press the [0] button.
3) Press the:
[STAY] button to send a test report to the Central Monitoring Station.
[FORCE] button to call the WinLoad software.
[ARM] button to answer the WinLoad software.
[DISARM] button to cancel communication with the WinLoad software.
You will only need to use the
Quick Function Buttons upon
your Installer’s or Central
Monitoring Station's request.
Only the System Master Code
or User Access Codes with
the Master feature enabled
will be able to access these
functions.
9.0 TESTING AND MAINTENANCE
9.1
BURGLAR ALARM TESTING
Two people are needed to complete this test. One person will watch the LCD screen on the keypad while the other
person walks around the protected areas and opens the zones (i.e. opens the doors and windows that are
protected, walk in the path of the motion detectors, etc.). The LCD screen will display the opened zones, but if a
zone does not register, contact your Installer.
9.2
FIRE ALARM TESTING
Do NOT use an open flame or burning materials to test your fire detection devices. Your Installer will provide details
on the best way to test your system.
LCD Keypad 19
9.3
9.4
SYSTEM MAINTENANCE
Under normal use your system requires no maintenance other than regular testing. We recommend that your
Installer change the battery every three years.
SYSTEM TEST
Speak to your Installer before
conducting a System Test
since the system must be
programmed to respond to
the test instructions. It is
normally recommended that
you conduct the system test
once a week, but contact your
Installer
for
instructions
concerning your particular
system.
How do I conduct the system test?
1) Call your Central Monitoring Station to advise them that you are testing your
system.
2) Enter your [ACCESS CODE].
3) Press the [8] button.
The system will test all its connections and can send a report to your Central
Monitoring Station. If the system detects a problem, the Trouble Display will
show on the LCD screen (Refer to section 7.0 on page 17). Call your Installer
for repairs if any Troubles occur.
10.0 FIRE AND BURGLAR ALARMS
10.1
STANDARD FIRE ZONE
During a fire alarm, the bell/
siren emits an intermittent
sound (BEEP-BEEP-BEEP) until
silenced or reset. If the zone
is a Standard Fire Zone, your
system can immediately send
an alert to your Central
Monitoring Station.
How do I disarm a false alarm?
1) Enter your [ACCESS CODE] on the keypad.
2) Call your Central Monitoring Station quickly to advise them of the false
alarm.
The Fire Zone may reset itself once the problem has cleared. If it does not, simultaneously
press and hold the [CLEAR] and [ENTER] buttons for two seconds.
10.2
DELAYED FIRE ZONE
If the zone is a Delayed Fire
Zone, there is an automatic
delay before your system
contacts
your
Central
Monitoring Station. Refer to
Figure 10.1 on page 21 to
prevent
unnecessary
reporting of false alarms.
What do I do if the fire alarm is accidentally triggered?
1) Press the [CLEAR] button within 30 seconds of the alarm.
2) Clear the problem from the area (i.e. clear the smoke from around the smoke
detector).
3) If the problem remains after 90 seconds, the alarm will sound again. Press
[CLEAR] again.
The system will delay reporting the alert for another 30 seconds.
If you are unable to cancel the false alarm, your system will send an alert. Call your Central
Monitoring Station to advise them of the false alarm.
The Fire Zone may reset itself once the smoke has cleared. If it does not, simultaneously
press and hold the [CLEAR] and [ENTER] buttons for two seconds or speak to your installer.
20 System Manager’s Manual
Figure 10.1: Delayed Fire Zone
10.3
FIRE SAFETY TIPS
How should you prepare in case of a fire in your home or business?
•
•
•
•
•
•
•
•
10.4
Remind everyone to escape first, then call for help.
Develop a fire escape plan and designate a meeting place outside.
Practice the escape plan frequently.
Plan two ways to escape from every room, if possible.
Practice feeling the way out with eyes closed.
Instruct everyone never to stand up during a fire, always crawl under the smoke and keep mouths covered.
Instruct everyone never to return to a burning building for any reason; it may cost them their life.
Check smoke alarms regularly. Working smoke alarms dramatically increase everyone's chances of surviving a fire.
MINIMIZING HOME FIRE HAZARDS
How can you avoid the three most common causes of fires at home?
• Never leave cooking food unattended. It is the leading cause of fire injuries. Cooking fires often result from unattended
cooking and human error, rather than mechanical failure.
• Stay alert when smoking. Careless smoking is the leading cause of fire deaths. Smoke detectors and smolder-resistant
bedding and upholstered furniture are significant fire deterrents.
• Maintain your heating system. Faulty heating systems are the second leading cause of residential fires.
10.5
10.6
HOME FIRE WARNING SYSTEM
Household fires are especially dangerous at night. Fires produce smoke and deadly gases that can overcome
occupants while they sleep. To warn against fire, smoke detectors should be installed outside each separate
sleeping area in the immediate vicinity of the bedrooms and on each additional story of the family living unit,
including basements.
BURGLAR ALARM
If your armed system is breached, the burglar alarm devices specific to your system will be triggered. If your keypad
is in Normal Mode:
• The Status Light may flash red
• “In Alarm” will appear on LCD screen.
• Bell or siren may be activated
In case of a burglar alarm, leave the premises and call the police station from a safe place.
LCD Keypad 21
Voice-Assisted Arm/Disarm Module
Operating Instructions
11.0 INTRODUCTION
Congratulations on choosing the Paradox InTouch Voice-Assisted Arm/Disarm Module (APR3-ADM2). InTouch
turns any touch-tone telephone into a keypad. With InTouch, you can now arm or disarm your Digiplex security
system as well as activate or deactivate your InTouch’s output all from your telephone. Using detailed voice prompts
to guide your way, the InTouch is as simple as picking up your telephone.
12.0 ACCESS CODES
InTouch uses your Digiplex User Access Code to grant you access to your Digiplex Security System. The User
Access Code entered on your Digiplex system keypad is the same you would use to enter on your telephone.
13.0 HOW DO I USE IT?
STEP 1:Pick up your telephone and dial the telephone number of the line that your InTouch is connected to. The
InTouch will now ask you to enter your Digiplex User Access Code.
STEP 2:Enter your Digiplex User Access Code.
If your Digiplex Security System is programmed to accept variable code lengths, you must
press the [#] key after entering your User Access Code.
STEP 3:Keys [1] to [4] on your telephone represent areas 1 to 4. To arm or disarm your Digiplex Security System,
press the desired area’s number on your telephone. This will toggle the area’s arming state from armed to
disarmed and vice versa (refer to section 16.0 on page 23).
STEP 4:To activate or deactivate the InTouch’s output, press the [#] key and then the [0] key (refer to section 16.0
on page 23).
14.0 THINGS YOU SHOULD KNOW
14.1
WHEN ACCESSING YOUR INTOUCH...
• If you are using an answering machine or service, call the InTouch, hang up after one ring, wait between 10 and 255
seconds (depending on how Intouch was programmed by your Installer), and then call the InTouch again to access it.
14.2
14.3
WHEN ARMING OR DISARMING...
• You will only be able to arm or disarm areas that your User Code has access to.
• If you were to arm an area with an open zone, Digiplex will Force arm the area. This will only happen with User Access
Codes that have the Force arming feature enabled.
WHEN ACTIVATING OR DEACTIVATING A PGM...
• Your InTouch’s output can be used to turn on lights, open or close a garage door and much more. Ask your installer
about this useful feature.
• If the InTouch’s output is not operational, you will not be able to activate or deactivate the output.
22 System Manager’s Manual
• Your installer can program the output to deactivate either manually or follow a timer. If programmed to be deactivated
manually, the output will remain activated until you deactivate it. If programmed to follow a timer, the output will
deactivate after the timer has elapsed.
14.4
WHEN USING YOUR INTOUCH...
• In some cases, your telephone’s tone may not be powerful enough to interrupt the InTouch’s voice prompt. If this is the
case, simply wait for the InTouch’s voice prompt to finish before entering your action.
• If your Digiplex Security System and InTouch share the same telephone number, you may be interrupted at times when
using your InTouch.
15.0 TELEPHONE BUTTON FEATURES
Clear = [*]
If you have made an error, press the [*] button on your telephone to clear the error and then re-enter the
information.
Activate/Deactivate InTouch Output = [#] , [0]
To activate or deactivate the InTouch’s output, press the [#] button and then the [0] button on your telephone.
Hang Up = [#] , [9]
When you wish to hang up, press the [#] button and then the [9] button to immediately hang up. The InTouch will
confirm the hang up with “Good-bye”.
If the hang-up feature is not used and if no action is performed after 2 minutes, the InTouch
will hang up automatically.
16.0 INTOUCH EXAMPLE
Nelson has a Digiplex Security System and an InTouch hooked up at home. His security system has two areas.
Both areas are presently armed and the InTouch’s output, which is hooked up to his garage door opener, is
deactivated. Nelson is on his way home and wishes to disarm both areas and open his garage door. Nelson
performs the following:
Nelson first dials the telephone number of the line to which the InTouch is connected to.
When the InTouch picks up, it will prompt Nelson with the following:
“Please enter your code.”
Nelson enters his User Access Code.
The InTouch then prompts Nelson with the following:
“Area 1 Armed”
“Area 2 Armed”
“Output is Deactivated”
“To modify, enter Area number”
Nelson presses the [1] key on his telephone to disarm Area 1.
Your User Access Code must also have access to the areas to which the InTouch is assigned
to.
LCD Keypad 23
The InTouch then prompts Nelson with the following:
“Area 1 Disarmed”
“Area 2 Armed”
“Output is Deactivated”
“To modify, enter Area number”
Nelson presses the [2] key on his telephone to disarm Area 2.
The InTouch then prompts Nelson with the following:
“Area 1 Disarmed”
“Area 2 Disarmed”
“Output is Deactivated”
“To modify, enter Area number”
Nelson then presses the [#] key and then the [0] key on his telephone to activate the output which in turn will
activate the garage door.
The InTouch then prompts Nelson with the following:
“Output is Activated”
Nelson then presses the [#] key and then the [9] key on his telephone to terminate the call.
The InTouch then prompts Nelson with the following:
“Goodbye”
17.0 INTOUCH SYSTEM CHECKLIST
Telephone Number: _____________________
Output Activates: _______________________
Output follows:
NOutput Timer
NManual Deactivation
Output Timer Length: ______ Nsec. or Nmin.
Call, hang-up, and then call back within ____ sec.
Number of rings before InTouch answers: ____
Partition Assignment: N1
24 System Manager’s Manual
N2
N3
N4
18.0 APPENDIX 1: HEBREW SPECIAL CHARACTERS
Refer to the following tables when programming the user labels (refer to section 5.2 on page 10) of a Hebrew
keypad.
Table 4: Hebrew Keypad Letter Assignment
Table 5: Hebrew Special Characters Catalogue
LCD Keypad 25
19.0 APPENDIX 2: RUSSIAN SPECIAL CHARACTERS
Refer to the following tables when programming the user labels (refer to section 5.2 on page 10) of a Russian
keypad.
Table 6: Russian Keypad Letter Assignment
Table 7: Russian Special Characters Catalogue
26 System Manager’s Manual
Warranty
The Seller warrants its products to be free from defects in materials and workmanship under normal use for a period
of one year (except as indicated otherwise). Except as specifically stated herein, all express or implied warranties
whatsoever, statutory or otherwise, including without limitation, any implied warranty of merchantability and fitness
for a particular purpose, are expressly excluded. Because Seller does not install or connect the products and
because the products may be used in conjunction with products not manufactured by Seller, Seller cannot
guarantee the performance of the security system. Seller obligation and liability under this warranty is expressly
limited to repairing or replacing, at Seller's option, any product not meeting the specifications. In no event shall the
Seller be liable to the buyer or any other person for any loss or damages whether direct or indirect or consequential
or incidental, including without limitation, any damages for lost profits, stolen goods, or claims by any other party
caused by defective goods or otherwise arising from the improper, incorrect or otherwise faulty installation or use of
the merchandise sold.
LCD Keypad 27
INDEX
A
Chime Zones
Access Codes
Deleting ...........................................................11
InTouch Access Codes ........................................22
Programming ....................................................12
System Master ....................................................9
User ..................................................................9
Access Control
Card Assignment ...............................................13
Entering & Exiting ..............................................15
Access Control User Options
Access to Armed Access Control Doors ..................15
Activate Card ....................................................14
Arming with Card ..............................................14
Can Disarm with Access Card ...............................14
Extended Unlocked Period ...................................14
Programming ....................................................13
Access Level
...........................................................13
Alarm Memory Display ................................................9
Alarm,Testing
.........................................................19
Area
Assignment ......................................................13
see also Partitioned System
.....................................14
...................................................6
Area Access, in User Options
Area Status Display
..........................................................19
Clock, Set Time and Date ..........................................18
Confidential Mode
D
Date, Set
......................................................6
...............................................................18
Deactivating a Security System ....................................8
Delay Timer
Entry .................................................................8
Exit ...................................................................6
Delayed Fire Zone
...................................................20
.......................................10
Deleting User Access Codes
Disarming
Armed System ....................................................9
InTouch ...........................................................22
with Card .........................................................15
Display
Alarms In Memory ...............................................9
Area Status ........................................................6
User Actions in Memory ......................................17
Duress, in User Options
............................................14
E
Emergency Buttons ..................................................19
Arming
Automatic Arming ................................................8
Force Arming ......................................................7
Instant Arming ....................................................7
Keyswitch Arming ................................................8
Regular Arming ...................................................6
Stay Arming .......................................................7
with Card .........................................................15
with InTouch ....................................................22
Entering and Exiting, Access Control Doors
Auto-Arming
No Movement Auto-Arming ...................................8
Timed Auto-Arming ..............................................8
Fire
........................................11
...............................................17
Exit Delay Timer ........................................................6
Extended Unlocked Period .........................................14
Erasing User Access Codes
Event Record Display
F
B
Battery
Disconnected ....................................................17
Low, in a Zone ..................................................17
Beep Tones
Confirmation beep ...............................................5
in Opened or Closed Zones, see Chime Zones
Rejection beep ....................................................5
....................................................17
........................................................21
Bell Disconnected
Burglar Alarms
Buttons
One-Touch .........................................................8
Quick Function ..................................................19
Bypass
Bypass Recall ......................................................7
Programming ......................................................7
C
Card, Access Control
Activating .........................................................14
Arming with ......................................................15
Assign .............................................................13
Disarming with ..................................................15
28 System Manager’s Manual
..................15
Entry Delay Timer ......................................................8
Delayed Fire Zone .............................................20
Minimizing Home Fire Hazards .............................21
Safety Tips .......................................................21
Standard Fire Zone ............................................20
Warning System ................................................21
..................................................19
............................................................7
Fire Alarm, Testing
Force Arming
H
Hebrew Special Characters
........................................25
I
Ignoring Zones when Arming, see Bypass Programming
Instant Arming ..........................................................7
InTouch
Access Codes ....................................................22
Accessing .........................................................22
Activating a Programmable Output .......................22
Arming ............................................................22
Deactivating a Programmable Output ....................22
Disarming ........................................................22
How to Use ......................................................22
Telephone Buttons .............................................23
K
Keypad, LCD
Buttons ..............................................................5
Lights ................................................................5
Messages ...........................................................5
Settings ...........................................................18
Keyswitch Arming
......................................................8
L
LCD Keypad ..............................................................5
Level, Access
..........................................................13
M
System Test
T
Tampered Zones
N
No Movement Auto-Arming
O
One-Touch buttons
.........................................8
....................................................8
..................................18
Outputs, Programmable (PGM)
P
Panic Alarms ...........................................................19
Partitioned System
....................................................6
Power Failure, see Trouble
Programmable Outputs (PGM)
Activating Through InTouch .................................22
in DigiplexNE Security System .............................18
Programming
Access Control Cards ..........................................13
Access Control User Options ................................13
Access Levels ....................................................13
Chime Zones ....................................................19
Schedules ........................................................13
User Access Codes ....................................... 12–13
User Options .....................................................12
Q
Quick Function Buttons
Answer Winload Sofware .....................................19
Call Winload Software ........................................19
Cancel Communication with Winload Software ........19
Send Test Report ...............................................19
.....................................................17
Testing and Maintenance
Burglar Alarm ...................................................19
Fire Alarm ........................................................19
System Maintenance ..........................................20
System Test .....................................................20
Time, Set
.............................................................9
Master Feature, in User Options .................................14
Master Code
..................................................9
...........................................................20
System Master Code
...............................................................18
Timed Auto-Arming ....................................................8
Timer
Entry Delay ........................................................8
Exit Delay ..........................................................6
Trouble
AC Failure ........................................................17
Battery ............................................................17
Bell/Siren Disconnected ......................................17
Clock ...............................................................17
Low Battery, Zone .............................................17
System ............................................................17
Zone Fault ........................................................17
Zone Tampering ................................................17
U
Unlocked Period, Extended
........................................14
User Options
Access Control, see Access Control User Options
Area Access ......................................................14
Arm Only .........................................................14
Bypass ............................................................14
Duress .............................................................14
Force Arm ........................................................14
Master Feature ..................................................14
Programming .............................................. 12–13
Stay & Instant Arm ............................................14
V
Viewing
Alarms In Memory ...............................................9
Area Status ........................................................6
User Actions in Memory ......................................17
R
..............................................7
.........................................................6
Request for Exit ......................................................15
Russian Special Characters ........................................26
Recall, Bypassed Zones
Regular Arming
S
......................................................21
..............................................................13
Safety Tips, Fire
Schedules
Separated System
see Partitioned System
..................................................17
.......................................25
Special Characters, Russian .......................................26
Standard Fire Zone ..................................................20
Stay Arming .............................................................7
Siren Disconnected
Special Characters, Hebrew
LCD Keypad 29
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement