INSTALLATION
INSTRUCTIONS
Attachment Kit
P/N 08B23-SDA-100A
Accessory
Application
IN-VEHICLE
ENTERTAINMENT SYSTEM
(WITH MOONROOF)
2007 ACCORD
4-DOOR
Publications No.
AII 32686
Issue Date
JULY 2006
Monitor bracket
i-VES harness
Washer-screw, 5 x 12 mm
(Not used)
Subharness
2 Washer-screws, 5 x 16 mm
2 Washer-screws, 5 x 25 mm
DIN Harness
5 Square-neck bolts
Room light harness
5 Flange nuts, 4 mm
Monitor gasket
Flange nut, 5 mm
(Not used)
16 Wire ties
Accord template
Wire ties with clip
TSX template (Not used)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
6 Cushion tapes
AII 32686 (0607)
08B23-SDA-1012-9A
1 of 21
Monitor Kit (sold separately):
P/N 08A23-2E1-010
Monitor console
Player Attachment Kit (sold separately):
P/N 08B06-SDA-101A
Left player bracket
DVD player
Right player bracket
FM modulator
Left player subbracket
Right player subbracket
Remote controller
Player base-bracket
(With YAW sensor)
2 Headphones
Player base-bracket
(Without YAW sensor)
5 Washer-screws, 5 x 8 mm
Player panel
2 Screw caps
Owner’s Manual
Pocket
2 of 21
AII 32686 (0607)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
Bus cable (not used)
TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
10 mm Combination wrench
Ratchet
7 mm, 10 mm and 12 mm Socket
2 Latches
8 Flange nuts, 6 mm
Torque wrench
Utility knife
File
Isopropyl alcohol
Masking tape
Piece of steel wire
Shop towel
Electrical tape
2 Self-tapping screws, 4 x 8 mm
Scissors
Hook tool
Illustration of the In-Vehicle Entertainment
System Installed on the Vehicle
2 Grommet screws
DIN
HARNESS
SUBHARNESS
i-VES
HARNESS
6 Wire ties
7 EPT sealers
DVD
PLAYER
MONITOR
ROOM LIGHT CONSOLE
HARNESS
2 Washer-bolts, 6 x 16 mm
FM
MODULATOR
2326010T
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
1.
Make sure you have the anti-theft code for the
radio, then write down the frequencies for the
preset buttons.
2.
Disconnect the negative cable from the battery.
AII 32686 (0607)
3 of 21
3.
Choose the Accord template; set the TSX
template aside, it will not be used. Using the utility
knife, cut out the marked areas from the template
(ACCORD) along the lines.
6.
Remove the trim ring.
M/T Model:
•
UTILITY
KNIFE
Without lock nut: Squeeze the plastic clip and
pull down on the shift boot. Remove the shift
knob by turning it counterclockwise.
TEMPLATE
(ACCORD)
PLASTIC
CLIP
SHIFT
KNOB
Cut out areas.
2D11010S
4.
SHIFT
BOOT
Close the sunshade. Position the template on the
headliner align the interior light and headliner clip,
and tape the template to the headliner using
strips of masking tape.
HEADLINER
CLIP
Cut out
INTERIOR
the area.
LIGHT
TRIM
RING
•
UTILITY
KNIFE
2206031K
With lock nut: Loosen the lock nut and remove
the gearshift knob.
SUNSHADE
SHIFT
KNOB
LOCK
NUT
MASKING
TAPE
HEADLINER
TEMPLATE
SHIFT BOOT
2031011S
5.
Using the utility knife, cut out the headliner around
the edge of the template.
4 of 21
AII 32686 (0607)
TRIM RING
5628100Y
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
•
Gently pry up on the trim ring to release the six
clips.
•
Unplug the two seat heater connectors (if
equipped), and remove the trim ring.
CLIPS (4)
7.
Remove the dashboard center holder:
•
Open the coin pocket lid and remove the coin
pocket.
•
Remove the two self-tapping screws.
•
Gently pull out on the dashboard center holder
to release the two retaining clips, unplug the
vehicle connector, and remove the center
holder.
CLIPS (2)
COIN
POCKET
LID
DASHBOARD
CENTER
HOLDER
SELF-TAPPING
SCREW
(Reuse.)
TRIM
RING
SEAT HEATER
CONNECTOR
(If equipped.)
CLIPS (2)
2206041K
VEHICLE
HARNESS
A/T Model:
•
•
5628120Y
Gently pry up on the trim ring to release the
six clips.
With Ashtray:
•
Open the lid and remove the ashtray.
Unplug the two seat heater connectors (if
equipped), and remove the trim ring.
•
Remove the two self-tapping screws.
•
Gently pull out on the two retaining clips,
unplug the cigarette lighter harness connector,
the vehicle connector, and the illumination
bulb; and then remove the center holder.
CLIPS (4)
ASHTRAY DASHBOARD
CENTER
SELFHOLDER
TAPPING
SCREW
(Reuse.)
CLIPS (2)
ILLUMINATION
BULB
TRIM
RING
SEAT HEATER
CONNECTOR
(If equipped.)
5628110Y
RETAINING
CLIPS (2)
CIGARETTE
LIGHTER
HARNESS
CONNECTOR
VEHICLE
CONNECTOR
5628130Y
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
AII 32686 (0607)
5 of 21
8.
Remove the pocket:
10. Remove the center dashboard upper cover.
•
Apply masking tape to the edge of the center
panel.
•
Remove the two self-tapping screws.
•
Attach electrical tape around the end of the
hook tool. Push on the bottom of the lid, then
pull out on the top by inserting the end of a
hook tool between the pocket and center
panel, and pulling it to out toward you to
release the two retaining clips. Take care not
to damage the lid.
•
Carefully insert a flat-tip screwdriver wrapped
with protective tape into the slots on both
sides of the upper cover, then pull out each
side of the panel at the bottom to detach the
clips.
CENTER DASHBOARD
UPPER COVER
CENTER
PANEL
ELECTRICAL
TAPE
MASKING
TAPE
HOOK TOOL
Push
RETAINING
CLIPS (2)
LID
FLAT-TIP
SCREWDRIVER
POCKET
CLIPS (2)
•
SELF-TAPPING
SCREW (Reuse.)
9.
2N11020T
Remove the right and left inner covers (one hook
and one clip for each cover).
2730030T
Push the bottom of the hazard warning switch,
and carefully insert a flat-tip screwdriver into
the slot at the bottom of the hazard warning
switch, then pry up the middle portion of upper
panel by releasing the center clip.
CENTER
DASHBOARD
UPPER COVER
CLIP
CLIP
HAZARD
SWITCH
LEFT INNER
COVER
RIGHT
INNER
COVER
POCKET
OPENING
HOOK
6 of 21
2226010K
AII 32686 (0607)
FLAT-TIP
SCREWDRIVER
2730040T
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
•
•
Using a hook tool, reach inside the vent and
locate the small opening on each side. Gently
pull out on the dash to release the eight clips.
12. Remove the driver’s dashboard lower cover:
Remove the center dashboard upper cover by
removing the two vehicle clips and unplugging
the vehicle connector(s).
HOOK
TOOL
Pull
•
Remove one self-tapping screw.
•
Release the four clips on the left side first by
gently pulling out on the driver’s dashboard
lower cover.
•
After releasing the four clips, insert the tip of
the screwdriver between the clip and the
dashboard frame. Gently twist the screwdriver
to release each clip.
•
Unplug the vehicle connector, and remove the
lower cover.
VEHICLE
CONNECTOR
VEHICLE
CLIPS (2)
CLIPS (8)
CLIP
CENTER
DASHBOARD
UPPER COVER
CLIP
(Release these
clips first.)
2206083K
VEHICLE
CONNECTOR
DRIVER’S
DASHBOARD
LOWER COVER
11. Remove the center panel (two bolts, three selftapping screws, and pull the center panel out
toward you to release the five clips).
CENTER
PANEL
2206121K
HOLDER
BOLT
2506030T
RETAINING
CLIPS (3)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
CLIPS (7)
13. If equipped, remove the driver’s dashboard under
cover (release the three retaining clips, one pin
and one holder).
SELF-TAPPING
SCREW
CLIPS (5)
SELFTAPPING
SCREW
AII 32686 (0607)
DRIVER’S
PIN
DASHBOARD
UNDER COVER
2705440T
7 of 21
14. Pry up on the four retaining tabs that fasten the
cap to the left front door sill and remove the cap.
17. Remove the left rear door sill (four clips).
CLIPS (4)
IGNITION
KEY
SELF-TAPPING
SCREW
CAP
LEFT REAR
DOOR SILL
RETAINING
TABS (4)
KEY
CYLINDER
LEFT FRONT
DOOR SILL
FRONT
2131020T
15. Remove the self-tapping screw. Insert the ignition
key into the key cylinder and turn it clockwise until
it will no longer turn. Using a flat-tip screwdriver,
pry up on the key cylinder and remove it from the
left front door sill.
2326060T
18. Release the center pillar upper anchor cover (three
tabs). Remove the left center pillar upper anchor
bolt.
16. Remove the left front door sill (five clips and two
retaining tabs).
LEFT CENTER
PILLAR UPPER
ANCHOR COVER
CLIPS (5)
LEFT FRONT
DOOR SILL
LEFT CENTER
PILLAR UPPER
ANCHOR BOLT
2319030M
FRONT
RETAINING
TABS (2)
8 of 21
2131010T
AII 32686 (0607)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
19. Remove the left center pillar lower anchor bolt.
CLIPS (4)
22. Remove the left and right lens from roof console
(four retaining tabs).
LEFT CENTER
PILLAR UPPER TRIM
ROOF
CONSOLE
FRONT
CENTER PILLAR
WEATHERSTRIP
RIGHT LENS
CENTER PILLAR
WEATHERSTRIP
LEFT LENS
RETAINING
TABS (4)
RETAINING
TABS (4)
2304010M
LEFT CENTER
PILLAR LOWER
TRIM
CENTER PILLAR
LOWER ANCHOR
BOLT
23. Remove the four bolts that fasten the roof
console. Remove the roof console by pulling it out
toward you, and unplugging the two vehicle
connectors.
2326070T
20. Remove the center pillar weatherstrip. Pull the left
center pillar lower trim and left center pillar upper
trim out toward you to release the four clips, and
remove the upper and lower trims.
VEHICLE
CONNECTOR
21. Remove the weatherstrip. Pull the left front pillar
trim out toward you to release the two clips, and
remove the left front pillar trim.
With SRS
CLIP
(Remove.)
ROOF
CONSOLE
CLIPS (2)
LEFT FRONT
PILLAR TRIM
BOLT
2301011M
WEATHERSTRIP
2304071M
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
AII 32686 (0607)
9 of 21
24. Remove the cap from the left sunvisor (four
retaining tabs).
27. Remove the two caps from the left rear grab rail,
and remove the grab rail (two bolts).
VEHICLE
CONNECTOR
CAP
RETAINING
TABS (4)
LEFT REAR
GRAB RAIL
CAP
BOLT
LEFT
SUNVISOR
2326100T
2326080T
TORX SCREW
Routing the i -VES Harness/Monitor Harness and
Installing the Monitor Console
25. Remove the left sunvisor (two T25 torx screws,
and unplug the connector).
26. Remove the two caps from the left front grab rail,
and remove the grab rail (two bolts).
28. Route the 90° end of the i -VES harness from the
left front pillar trim opening to the dashboard
lower cover opening.
i -VES
HARNESS
CAP
LEFT FRONT
PILLAR TRIM
OPENING
i -VES
HARNESS
LEFT FRONT
GRAB RAIL
BOLT
2326090T
90°
TERMINAL
END
DASHBOARD LOWER
COVER OPENING
10 of 21
AII 32686 (0607)
2326202T
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
29. Continue routing the 90° end of the i -VES harness
from the dashboard lower cover opening to the
pocket opening on the driver’s seat side.
31. Route the i-VES harness up along the front pillar
and under the headliner along side the vehicle
harness.
POCKET
OPENING
VEHICLE
HARNESS
i-VES
HARNESS
HEADLINER
90°
TERMINAL
END
2326221T
DASHBOARD
LOWER COVER
OPENING
i -VES
HARNESS
2326192T
32. Continue routing the i-VES harness to the rear
along the vehicle harness, and out of headliner
opening you made, so that the distance between
the headliner opening and i -VES harness
terminal end is 14¾ in. (370 mm).
30. Remove the sunvisor holders. Using a flat-tip
screwdriver, push the hook, and turn the holder
90°, then pull it out.
HEADLINER
OPENING
14¾ in.
(370 mm)
i-VES
HARNESS
VEHICLE
HARNESS
2326231T
SUNVISOR
HOLDERS (2)
FLAT-TIP SCREWDRIVER
2326210T
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
AII 32686 (0607)
11 of 21
33. Using isopropyl alcohol on a shop towel, clean the
area where the cushion tape will attach. Secure
the i-VES harness to the underside of the vehicle
frame with the two cushion tapes.
37. Route a piece of steel wire through the hole in
the rear interior light opening and out through the
cutout made in the headliner.
REAR INTERIOR
LIGHT OPENING
ELECTRICAL TAPE
CUSHION
TAPES (2)
HEADLINER
OPENING
BRACKET
PIECE OF STEEL WIRE
(Wrap the end around the
terminal end of the room light
harness and pull it up.)
WIRE TIES (2)
ROOM LIGHT
HARNESS
VEHICLE
2326250T
HARNESS
i-VES
HARNESS
WIRE TIES (2)
3204030Y
34. Secure the i-VES harness to the vehicle harness
with four wire ties in the areas shown.
38. Wrap the end of the steel wire around the room
light harness connector and secure with an
electrical tape. Pull the room light harness up
through the rear interior light opening and out
through the headliner opening.
35. Release the rear interior light.
•
Remove the lens (four retaining clips).
•
Remove the two screws, lift out the light,
unplug the connector, and remove the light.
VEHICLE CONNECTOR
FRONT
INTERIOR
LIGHT
LENS
CLIP
(Turn 90°
counterclockwise
to remove.)
SCREW
2326240T
36. Remove the headliner clip by turning it 90°
counterclockwise.
12 of 21
AII 32686 (0607)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
39. Plug the room light harness 3-pin connectors in
between the rear interior light and vehicle 3-pin
connectors and wrap one EPT sealer around the
3-pin connectors.
42. Using isopropyl alcohol on a shop towel, clean the
area where the cushion tape will attach. Attach the
remaining piece of cushion tape to the monitor
bracket in the area shown.
VEHICLE 3-PIN
CONNECTOR
EPT
SEALER
MONITOR
BRACKET
HALF
CUSHION
TAPE
ROOM LIGHT
HARNESS 3-PIN
CONNECTOR
ROOM LIGHT
HARNESS 3-PIN
CONNECTOR
CUSHION
TAPE
3204060Y
REAR INTERIOR
LIGHT
CUSHION
TAPE
ROOM
LIGHT
HARNESS
43. Insert the monitor bracket into the headliner
opening.
3204050Y
HEADLINER
OPENING
40. Using isopropyl alcohol, thoroughly clean the area
where the cushion tapes will attach. Cut one
cushion tape in half, and secure the room light
harness to the headliner with one cut cushion
tape and one full cushion tape in the areas
shown.
41. Reinstall the rear interior light.
MONITOR
BRACKET
5629100Y
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
AII 32686 (0607)
13 of 21
44. Install the monitor bracket to the vehicle frame
with five square-neck bolts and five 4 mm flange
nuts while holding the square-neck bolts.
46. Connect the interior light harness 3-pin connector
and the i-VES harnesses terminal to the monitor
console 3-pin connector and monitor console
terminal.
INTERIOR LIGHT
HARNESS 3-PIN
CONNECTOR
VEHICLE
FRAME
SQUARENECK
BOLTS (5)
MONITOR
BRACKET
SQUARENECK
BOLTS (5)
i-VES
HARNESS
TERMINAL
MONITOR
CONSOLE
TERMINAL
MONITOR
CONSOLE 3-PIN
CONNECTOR
VEHICLE
4 mm
FLANGE
NUTS (5)
MONITOR
CONSOLE
FRONT
3205030Y
MONITOR
BRACKET
47. With an assistant holding the monitor console,
secure the 3-pin connectors and terminals you
plugged to the back of the monitor console.
5629110Y
45. Remove the left and the right lens from the
monitor console, then install the monitor gasket
on the console while aligning the arrow( ) on the
monitor gasket with the arrow( ) on the monitor
console.
3-PIN
CONNECTOR
LEFT LENS
RIGHT
LENS
MONITOR
CONSOLE
TERMINAL
MONITOR
CONSOLE
CUSHION
TAPE
3-PIN
CONNECTOR
ARROW( )
MONITOR
GASKET
2326290T
14 of 21
TERMINAL
5629120Y
48. Secure the 3-pin connector and the terminal to the
monitor console with one cushion tape.
AII 32686 (0607)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
49. Position the monitor console on the monitor
bracket and install the two 5 x 16 mm washerscrews and the two 5 x 25 mm washer-screws.
Install the two screw caps, then reinstall the left
and right lenses. Do not pinch the i-VES harness
and monitor harness between the monitor console
and the monitor bracket.
MONITOR
CONSOLE
With Day/Night Mirror:
i-VES
HARNESS
WIRE TIES (4)
VEHICLE
HARNESS
MONITOR
BRACKET
VEHICLE
CLIP
FRONT
5 x 25 mm
WASHER
SCREW
VEHICLE
HARNESS
LEFT
FRONT
PILLAR
RIGHT
LENS
LEFT
LENS
5 x 16 mm
WASHER
SCREW CAP SCREW
i-VES
HARNESS
SCREW
CAP
2306052M
DAY/NIGHT
MIRROR
HARNESS
51. Near the fuse box by the dashboard lower cover
opening, secure the i-VES harness to the vehicle
harness with three wire ties in the areas shown.
2326322T
50. Along the front pillar, secure the i-VES harness to
the vehicle harness with the four wire ties.
VEHICLE
HARNESS
Without Day/Night Mirror:
i-VES
HARNESS
WIRE TIES (4)
WIRE TIE
VEHICLE
HARNESS
i-VES
HARNESS
VEHICLE
CLIP
VEHICLE
HARNESS
FUSE BOX
WIRE
TIE
2326330T
2306042M
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
AII 32686 (0607)
15 of 21
52. Continue to secure the i -VES harness to the
vehicle harness with the three wire ties in the
areas shown.
55. Route the other end of the subharness behind
navigation unit or audio unit, and plug the
subharness 20-pin connector into the rear of the
navigation unit or audio unit, then reinstall the
center panel. On navigation unit equipped
vehicles, place the subharness connector between
the bracket and air duct.
VEHICLE
HARNESS
With Navigation System:
CENTER
PANEL
NAVIGATION
UNIT
i-VES
HARNESS
2326340T
WIRE TIE
Installing the DVD Player
2326361T
53. Unplug the vehicle 20-pin connector from the
audio unit or navigation unit. Route the
subharness as shown, and plug the subharness
20-pin connector into the vehicle 20-pin
connector.
SUBHARNESS
20-PIN CONNECTOR
Without Navigation System:
SUBHARNESS 20-PIN
CONNECTOR
VEHICLE
FRAME
WIRE
TIE
CENTER
PANEL
AUDIO UNIT
VEHICLE
HARNESS
VEHICLE
20-PIN
CONNECTOR
20-PIN
CONNECTOR
AUDIO UNIT
OR NAVIGATION UNIT
SUBHARNESS
20-PIN CONNECTOR
SUBHARNESS
20-PIN
CONNECTOR
2326371T
SUBHARNESS
5411020Y
54. Secure the connected 20-pin connectors to the
vehicle frame with two wire ties.
16 of 21
AII 32686 (0607)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
If the vehicle is equipped with a YAW sensor, continue
with step 56; otherwise, go to step 60.
60. Remove the vehicle harness clip, and pull the
harness away from the bracket.
56. Remove the vehicle clip from the left side of the
pocket opening.
61. Install the player base bracket.
VEHICLE CLIP
(Cut and remove.)
VEHICLE CLIP
•
VEHICLE
HARNESS
With YAW sensor: Install the player basebracket to the vehicle frame, using two
6 x16 mm washer bolts and two 6 mm flange
nuts the bracket firmly against the vehicle
frame.
WIRE TIE
PLAYER
BASE-BRACKET
VEHICLE FRAME
6 mm
FLANGE
NUT
VEHICLE
HARNESS
VEHICLE
BRACKET
6 x 16 mm
WASHER
BOLT
POCKET
OPENING
VEHICLE
FRAME
5628141Y
57. Using diagonal cutters, cut and remove the
vehicle clip. Secure the vehicle harness to the
vehicle harness using one wire tie.
58. Remove the vehicle clip from the right side of the
pocket opening as shown.
VEHICLE CLIP
VEHICLE
BRACKET
EPT SEALER
VEHICLE
HARNESS CLIP
(Remove.)
•
5411031Y
Without YAW sensor: Install the player basebracket to the vehicle frame, then install the
two 6 mm flange nuts while holding the bracket
firmly against the vehicle frame.
PLAYER
BASE-BRACKET
VEHICLE
FRAME
VEHICLE CLIP
(Cut and remove.)
VEHICLE
HARNESS
VEHICLE
FRAME
POCKET
OPENING
6 mm
FLANGE
NUT
5628150Y
59. Using diagonal cutters, cut and remove the
vehicle clip. Wrap one EPT sealer around the
vehicle harness.
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
VEHICLE
HARNESS CLIP
(Remove.)
AII 32686 (0607)
2530270T
17 of 21
62. Position the FM modulator on the player basebracket and install the 5 x 8 mm washer-screw.
DIN HARNESS
66. Install the left and right player subbrackets into
the holes in the vehicle frame, then install one
6 mm flange nut onto the stud of each subbracket
while pushing the player subbracket upward.
FM
MODULATOR
VEHICLE
FRAME
90° DIN
HARNESS
TERMINAL
6 mm FLANGE
NUT
VEHICLE
FRAME
FM
MODULATOR
ANTENNA
LEAD
5 x 8 mm
WASHERSCREW
5411040Y
PLAYER
BASE-BRACKET
LEFT PLAYER
SUBBRACKET
63. Plug the 90° DIN harness terminal into the FM
modulator (not the i -VES harness).
64. On the right of the dashboard opening, unplug the
vehicle antenna leads and plug into the FM
modulator antenna lead. Plug the FM modulator
antenna lead into the other vehicle antenna lead.
DASHBOARD
OPENING
PLAYER
BASE-BRACKET
WIRE TIE
i -VES
HARNESS
FM
MODULATOR
ANTENNA
LEAD
FM
MODULATOR
ANTENNA
LEAD
5409020Y
67. Align the end of the i -VES terminal with the end
of the DIN harness terminal, and loop the
harnesses. Secure the harness with two wire ties.
VEHICLE
ANTENNA
LEAD
VEHICLE
ANTENNA
LEAD
RIGHT PLAYER
SUBBRACKET
VEHICLE
HARNESS
ANTENNA
LEADS
WIRE TIE
WIRE TIE
WITH CLIP
VEHICLE
HARNESS
5411050Y
DIN HARNESS
5411061Y
65. Wrap the FM modulator antenna lead and vehicle
harness you removed with one wire tie with clip,
and push the wire tie with clip into the hole in the
player base-bracket.
18 of 21
AII 32686 (0607)
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
68. To protect the center panel apply masking tape in
the area shown.
70. Using scissors, cut one EPT sealer to the
dimensions shown.
CENTER
PANEL
EPT SEALER
10 mm
Cut off the
excess part.
MASKING
TAPE
Cut off.
10 mm
DVD PLAYER
2829040M
2506010T
71. Attach the two cut EPT sealers to the DVD player
and cut off the excess portion.
69. Get the pocket. Using a utility knife, cut the two
lugs off of the pocket.
72. Install one latch into each left and right player
bracket.
LUG
(Cut off.)
1 mm
1 mm
LATCH
LATCH
LATCH
LATCH
LEFT PLAYER
BRACKET
PLAYER
LUG
POCKET
5 x 8 mm
WASHERSCREWS (4)
POCKET RIGHT PLAYER
4 x 8 mm
BRACKET
SELF-TAPPING
4 x 8 mm
SCREW
SELF-TAPPING
SCREW
2529041T
2306031T
73. Position the DVD player and pocket on the left
and right player brackets, and install four 5 x 8 mm
washer-screws from the player kit, and the two
4 x 8 mm self-tapping screws from the player
attachment kit.
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
AII 32686 (0607)
19 of 21
74. Plug the subharness 4-pin connector, the DIN
harness terminal and the i -VES harness terminal
into the rear of the DVD player (plug the i -VES
harness terminal into the yellow label position).
DVD
PLAYER
76. Cut the excess piece of EPT sealer (from step 70)
to the dimensions shown.
PLAYER
PANEL
EPT SEALER
(Cut off the
marked area.)
YELLOW
LABEL
i -VES HARNESS
TERMINAL
8 mm
SUBHARNESS 4PIN
CONNECTOR
DIN
HARNESS
TERMINAL
2612010T
Excess piece of
EPT sealer from
step 71.
5803010Y
75. Install the DVD player to the brackets using four
6 mm flange nuts.
77. Clean the player panel with isopropyl alcohol
where the EPT sealers will be attached. Attach
the EPT sealer to the player panel and cut off the
excess EPT sealer.
LEFT PLAYER
SUBBRACKET
DVD
PLAYER
8 mm
RIGHT
PLAYER
SUBBRACKET
78. Attach the two grommet screws to the player
panel.
PLAYER
PANEL
6 mm
FLANGE
NUT
POCKET
PLAYER BASE
BRACKET
5411070Y
GROMMET
SCREW
20 of 21
AII 32686 (0607)
2306131T
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
79. Insert the player panel clips into latches, and
attach the player panel to the instrument panel
with the two self-tapping screws removed in
step 8. Remove the masking tape.
81. Reconnect the negative cable to the battery.
82. Enter the customer’s radio anti-theft code, and
reset the radio station presets.
LATCH
PLAYER
PANEL
80. Check that all wire harnesses are routed properly
and all connectors are plugged in.
83. Set the clock.
CLIP
84. Check the operation of the in-vehicle
entertainment system according to the its
Owner’s Manual.
85. Put the in-vehicle entertainment system Owner’s
Manual in the glove box.
86. Reinstall all removed parts. Torque the seat belt
anchor bolts: 30 to 35 N·m(21 to 25 lbf·ft)
NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
87. Start the engine. Push down fully on the driver’s
window switch until the window is fully open.
SELF-TAPPING
SCREW
(reused)
5409050Y
88. Pull up fully on the driver’s window switch to close
the window completely, then hold the switch for
2 second or more.
89. Test the window AUTO function.
© 2006 American Honda Motor Co., Inc. - All Rights Reserved.
AII 32686 (0607)
21 of 21
">
