Direct IP IDIS DR-1504P Operation Manual

Network
Video
Recorder
Operation Manual
DR-1504P
DR-1508P
Powered by
Before reading this manual
This operation manual contains basic instructions on installing and using DirectIP Network Video Recorder, an IDIS
product. Users who are using this product for the first time, as well as users with experience using comparable
products, must read this operation manual carefully before use and heed to the warnings and precautions contained
herein while using the product. Safety warnings and precautions contained in this operation manual are intended to
promote proper use of the product and thereby prevent accidents and property damage and must be followed at all
times. Once you have read this operation manual, keep it at an easily accessible location for future reference.
• The manufacturer will not be held responsible for any product damage resulting from the use of unauthorized parts and
accessories or from the user's failure to comply with the instructions contained in this operation manual.
• It is recommended that first-time users of DirectIP™ Network Video Recorder and individuals who are not familiar with its
use seek technical assistance from their retailer regarding product installation and use.
• If you need to disassemble the product for functionality expansion or repair purposes, you must contact your retailer and
seek professional assistance.
• Both retailers and users should be aware that this product has been certified as being electromagnetically compatible for
commercial use. If you have sold or purchased this product unintentionally, please replace with a consumer version.
Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the
presence of uninsulated "dangerous voltage" within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Symbol
Publication
Description
IEC60417, No.5032
Alternating current
IEC60417, No.5031
Direct current
WARNING
Hazardous moving parts
Keep away from moving fan blades
AVERTISSEMENT
Pièces mobiles dangereuses
Se tenir éloigné des pales de ventilateurs mobiles
2
Before reading this manual
1. Read Instructions
All the safety and operating instructions should be read before the appliance
is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Cleaning
Unplug this equipment from the wall outlet before cleaning it. Do not use
liquid aerosol cleaners. Use a damp soft cloth for cleaning.
4. Attachments
Never add any attachments and/or equipment without the approval of the
manufacturer as such additions may result in the risk of fire, electric shock or
other personal injury.
5. Water and/or Moisture
Do not use this equipment near water or in contact with water.
6. Ventilation
Place this equipment only in an upright position. This equipment has an
open-frame Switching Mode Power Supply (SMPS), which can cause a fire or
electric shock if anything is inserted through the ventilation holes on the side
of the equipment.
7. Accessories
Do not place this equipment on an unstable cart, stand or table. The
equipment may fall, causing serious injury to a child or adult, and serious
damage to the equipment. Wall or shelf mounting should follow the
manufacturer's instructions, and should use a mounting kit approved by the
manufacturer.
This equipment and cart combination should be moved with care. Quick
stops, excessive force, and uneven surfaces may cause the equipment and cart
combination to overturn.
8. Power Sources
This equipment should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power, please
consult your equipment dealer or local power company. This equipment
should be remain readily operable.
9. Power Cords
Operator or installer must remove power and TNT connections before
handling the equipment.
10. Lightning
For added protection for this equipment during a lightning storm, or when it
is left unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent damage
to the equipment due to lightning and power-line surges.
11. Overloading
Do not overload wall outlets and extension cords as this can result in the risk
of fire or electric shock.
12. Objects and Liquids
Never push objects of any kind through openings of this equipment as they
may touch dangerous voltage points or short out parts that could result in a
fire or electric shock. Never spill liquid of any kind on the equipment.
13. Servicing
Do not attempt to service this equipment yourself. Refer all servicing to
qualified service personnel.
14. Damage requiring Service
Unplug this equipment from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
A. When the power-supply cord or the plug has been damaged.
B. If liquid is spilled, or objects have fallen into the equipment.
C. If the equipment has been exposed to rain or water.
D. If the equipment does not operate normally by following the operating
instructions, adjust only those controls that are covered by the operating
instructions as an improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the equipment to its normal operation.
E. If the equipment has been dropped, or the cabinet damaged.
F. When the equipment exhibits a distinct change in performance − this
indicates a need for service.
15. Replacement Parts
When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or that have the same
characteristics as the original part. Unauthorized substitutions may result in
fire, electric shock or other hazards.
16. Safety Check
Upon completion of any service or repairs to this equipment, ask the service
technician to perform safety checks to determine that the equipment is in
proper operating condition.
17. Field Installation
This installation should be made by a qualified service person and should
conform to all local codes.
18. Correct Batteries
Warning: Risk of explosion if battery is replaced by an incorrect type. Replace
only with the same or equivalent type. Dispose of used batteries according to
the instructions. The battery shall not be exposed to excessive heat such as
sunshine, fire or the like.
Avertissement: risque d'explosion en cas d'utilisation d'une batterie de type
incorrect. Le remplacer uniquement par un type identique ou équivalent.
Mettre les batteries usées au rebut conformément aux instructions. La batterie
ne doit pas être exposée à une source de chaleur excessive, telle que le soleil,
le feu, ou analogue.
19. Tmra
A manufacturer’s maximum recommended ambient temperature (Tmra)
for the equipment must be specified so that the customer and installer may
determine a suitable maximum operating environment for the equipment.
20. Elevated Operating Ambient Temperature
If installed in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient.
Therefore, consideration should be given to installing the equipment in an
environment compatible with the manufacturer’s maximum rated ambient
temperature (Tmra).
21. Reduced Air Flow
Installation of the equipment in the rack should be such that the amount of
airflow required for safe operation of the equipment is not compromised.
22. Mechanical Loading
Mounting of the equipment in the rack should be such that a hazardous
condition is not caused by uneven mechanical loading.
23. Circuit Overloading
Consideration should be given to connection of the equipment to supply
circuit and the effect that overloading of circuits might have on over current
protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
24. Reliable Earthing (Grounding)
Reliable grounding of rack mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct
connections to the branch circuit (e.g., use of power strips).
HDMI Port Precautions
• Use a certified cable marked with an HDMI logo when using HDMI.
The screen may not display or a connection error may occur if you do
not use a certified HDMI cable.
• It is recommended that you use the following HDMI cable type.
– High-speed HDMI Cable
– High-speed HDMI Cable with Ethernet
3
Before reading this manual
Important Safeguards
In-Text
Symbol
Type
Caution
Note
Description
Important information concerning a specific function.
Useful information concerning a specific function.
User’s Caution Statement
Caution: Any changes or modifications to the equipment not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
FCC Compliance Statement
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART
15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE
WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE
RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE
HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO
CAUSE HARMFUL INTERFERENCE, IN WHICH CASE USERS WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.
WARNING: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS OF DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE CAUSING EQUIPMENT
REGULATIONS.
WEEE (Waste Electrical & Electronic Equipment)
Correct Disposal of This Product
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the environment or human health from
uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote
the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This
product should not be mixed with other commercial wastes for disposal.
4
Before reading this manual
Copyright
© 2022 IDIS Co., Ltd.
IDIS Co., Ltd. reserves all rights concerning this operation manual.
Use or duplication of this operation manual in part or whole without the prior consent of IDIS Co., Ltd. is strictly
prohibited.
Contents of this operation manual are subject to change without prior notice.
Registered Trademarks
IDIS is a registered trademark of IDIS Co., Ltd.
Other company and product names are registered trademarks of their respective owners.
The information in this manual is believed to be accurate as of the date of publication even though explanations of some
functions may not be included. We are not responsible for any problems resulting from the use thereof. The information
contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate
such changes.
The software included in this product contains some Open Sources. You may obtain the complete corresponding source code
depending on whether or not the source is publicly available under a license policy. Go to System Setup - About page for
more information. This product includes software developed by the University of California, Berkeley and its contributors, and
software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/). Also, this product includes
cryptographic software written by Eric Young ([email protected]), and software written by Tim Hudson ([email protected]).
5
Table of Contents
1
Part 1 - Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setting Password. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Setup Wizard. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Camera Registration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Camera Scan Button. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Camera View Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Camera List Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Video Display Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Apply/Cancel Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Diagnosis Process. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Camera Registration Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Live Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
PTZ Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Event Monitoring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Covert Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Context Menu Access . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Edit Group. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Video Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Panic Recording. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Video Recording Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
All Channel Playback. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2
Part 2 - Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Menu Use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Text Input via Virtual Keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Batch Assignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Mouse. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Date/Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6
User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Self-Diagnosis. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Custom Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
About. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Camera Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Registration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Advanced Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Stream I. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Stream II. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Record Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Pre-Event. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Event Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
System_Event. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Camera System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Camera System_Video Loss. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Camera System_Recording Fail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Camera System_PIR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Video-Analytics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Video-Analytics_Motion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Video-Analytics_Trip Zone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Video-Analytics_Tampering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Video-Analytics_Auto Tracking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Network Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
WAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
FEN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Firewall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Notification Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Callback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Mail. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
7
Push. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
HTTP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Display Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Main Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Status Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Camera. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
3
Part 3 - Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Time-Lapse Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Search Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Context Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Clip Copy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Event Log Search. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Overlapped Recording Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Memo. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .84
8
Part 1 - Getting Started
This document covers the 4- and 8- channel
network video recorders. The NVRs are identical
except for the number of cameras that can be
connected and the number of cameras that can
be displayed. For simplicity, the illustrations
and descriptions in this document refer to the
4-channel model.
Setting Password
1
Setup Wizard
Setup Wizard lets you configure basic settings required
for operating the system.
Setup Wizard only appears during initial booting.
When you login as an administrator account after
initial booting, you can use Wizard to go to Live menu
and select Wizard.
1
Select a system language.
The users must first run the system and then be
required to set the password for the admin user
account.
Select Cancel from any of the Wizard screen to
cancel the setup process and return to the main
setup menu.
• It does not allow a user to run the system
without a password.
• Click the question mark button on the bottom
left corner and refer to the instruction on
setting up a password.
• An email address and UPR files are required to
find the password. Otherwise, you may not be
able to find your password when you enter the
incorrect information.
9
Part 1 - Getting Started
Quick Wizard
1
2
3
Choose the desired Recording Method and click
Next.
4
Choose the desired Recording Quality and click
Next.
Select Quick Wizard.
Specify the current date and time and then click
Next.
• The new date and time settings will only be
applied after clicking Next.
• For more information on date and time
settings, refer to the Date/Time section under
System Setup on page 31.
• Higher recording quality uses up more disk
space.
• Recording resolution is determined based on
the selected recording quality.
– High Video Quality Priority Profile: Very
high
– Standard Recording Profile: High
– Longer Recording Time Priority Profile:
Standard
10
Part 1 - Getting Started
– Recording resolutions used under each recording method
and record video quality setting are as follows:
5
6
High Video Quality Standard
Priority Profile
Recording
Profile
Longer Recording
Time Priority
Profile
Motion
Event
Record
Profile 1
Profile 2
Profile 3
Continuous
& Motion
Event
Record
Profile 2
(Continuous) /
Profile 1 (Motion)
Profile 3
(Continuous)
/ Profile 2
(Motion)
Profile 4
(Continuous) /
Profile 3(Motion)
Continuous
Profile 1
Profile 2
Profile 4
Network Wizard
After exiting from Quick Wizard, the network with
Network Wizard will start automatically.
1
Select Network Wizard.
2
Specify whether the system is connected to the
Internet and click Next.
Choose the desired codec and click Next.
Click Finish to exit Quick Wizard.
If you have chosen No, wait for the test to finish
and then click Finish to exit Network Wizard.
11
Part 1 - Getting Started
3
Select Network Configuration and then click
Next. Select either Auto Configuration or Manual
Configuration and then click Test to test the system’s
current network configuration.
• This test must be performed before proceeding
to the next step.
• If the NVR is on a network connected to a
network that has a DHCP server, selecting Auto
Configuration retrieves LAN settings such as
IP and DNS addresses automatically. Selecting
Manual Configuration, on the other hand, lets
you specify the settings manually.
• UPnP support device not found. If this error
message is displayed, check to see if the IP
router (or NAT) supports UPnP and if UPnP has
been enabled. For more information about the
router's UPnP function, refer to the router's
operation manual.
12
4
Enter in the Device Name field the NVR name to be
registered on the FEN server and then click Check to
check its availability.
• The device name you register on the FEN server
will be a unique name used to identify the
NVR. Once registered, the name can be used
to access the NVR directly from clients such as
the IDIS Center. Check the name's availability
to complete the registration process. The Finish
button will then become activated.
• You will be prompted with an error message if
you do not enter a name for the NVR or enter a
name already registered on the FEN server.
• Depending on the network environment,
FEN services may not be active and therefore
prevent the NVR from connecting to the
network. In this case, you will need to manually
configure the ports. For more information on
port configuration, refer to Network Setup on
page 64.
Part 1 - Getting Started
5
Click Finish to exit Network Wizard.
Camera Registration
Once Network Setup Wizard is complete, live mode
screen appears. While in live mode, right-click on the
mouse and select Camera Registration to run the
Camera Registration mode. It allows you to scan for the
cameras connected to the NVR.
2
1
3
4
5
1
Camera Scan Button
2
Camera View Menus
3
Camera List Area
4
Video Display Area
5
Apply/Cancel Buttons
You can also register cameras on the remote
program. For more information on the remote camera
registration, refer to Registration on page 13.
13
Part 1 - Getting Started
Camera Scan Button
● Mode: Select the scan mode.
– Auto Scan (LAN): Lists cameras in a LAN
environment. If Auto Scan (LAN) fails to recognize
a camera, try using IP Address Scan instead.
You can scan and search and register cameras that were
not detected automatically or third party cameras.
Pressing the Scan button displays the following submenu.
Rescan
– IP Address Scan: Enter the IP address of a
camera. The NVR scans for the camera matching
the specified address. If you enter IP address’s
range, the NVR scans for cameras falling under
the specified address’s range. By specifying an IP
address, you can also specify which port to use with
the Remote Admin feature. It is recommended that
the camera not be networked via DHCP (Dynamic
Host Configuration Protocol). If the camera is
networked via DHCP, connection to the camera may
not be made properly depending on changes in the
external network environment.
1
Only cameras that are connected to the NVR via VIDEO
IN ports can be scanned and registered.
Scans for DirectIP™ cameras that were not scanned
automatically.
Third Party Scan
Scans for IDIS Open cameras that do not support
automatic scan feature.
● Protocol: Select the protocol used by the camera (or
video encoder) you wish to search for.
• Some functions may not be supported for the
third-party cameras depending on their protocol
and model.
14
Select Scan to commence scanning.
2
Select a camera from the scan list and then select
Add Camera. The device login window will appear.
3
Enter a User ID and a Password for the selected
camera.
Part 1 - Getting Started
Set Camera Password
Search Scope
For IDIS protocol cameras that support changing and
finding the camera password, you must set the camera
password at the time of initial camera registration. The
email information is used to change and find the camera
password.
Filters the cameras in the camera list depending on the
search scope such as specified IP address rang
Screen Auto. Assign
Assigns the detected cameras on the video display area.
Camera list
Go To Camera
By using the camera information file, .csv, the user can
register the cameras easily.
Moves the focus automatically to the camera using the
MAC addressa and model of camera in the camera list.
● Export : Button : Exports the list of camera
information on USB as a .csv file
● Import : Button : Imports a camera information file,
.csv file. The user can edit a csv file directly.
• A column indicates camera number, B
column the camera MAC address, C column
the Video In port of the video encoder in the
.csv file. C column indicates only for video
encoders. If camera information displays
as follows: 5,00:11:22:18:30:20,3, 5 = CAM 5,
5,00:11:22:18:30:20 = MAC address, 3 means video
encoder.
• Before using this feature, the cameras must be
scanned first. If the cameras to be registered
do not exist in the list, the camera cannot be
registered.
• This feature is not supported for the third-party
cameras.
15
Part 1 - Getting Started
Scan Refresh Interval
Configures the refresh interval to scan the camera. If
the interval is short, camera scan results are refreshed
more frequently. However, if the interval is long, it is
advantageous to scan cameras on a wide network.
Camera View Buttons
● ALIGNMENT
Button: Realigns camera screens
displayed on the video display area in the order of
Video In port connections.
Button: Refreshes the video display area
● RESET
and the camera list.
Selecting RESET clears all scanned devices from the
list.
● Bitrate Button: Displays the following window to
change the bitrate allocation for each channel.
When registering the camera, you can set the stream
as much as the performance (bitrate) assigned to the
channel. If high performance (bitrate) is not allocated,
Quailty, IPS and Resolution can be low. If a channel
has a camera already registered, bitrates may not be
lower than current stream settings. You can change
the bitrate by pressing the + - button at the bottom
left. Only the bitrate of the registered camera can be
changed by checking the registered channel (*).
● Tool Button: Displays network camera tool
window to run a camera-related actions. There are
Authentication, Screen Assignment and Camera
Protocol Change for actions.
1
Select an Action to execute.
2
Select a camera from the list and press the Apply
button.
16
IDIS cameras can be detected automatically but
IDIS protocol cannot be detected automatically.
We recommend you use the DirectIP protocol
to detect the cameras automatically. When you
change the protocol, the camera reboots and then
you can register the camera on the NVR. For more
information on the settings, please refer to the
network camera manual.
Part 1 - Getting Started
Camera List Area
Following options can be accessed by right-clicking on a
camera list entry:
● Add/Remove Camera: Adds or removes the selected
camera. The Add Camera option is inactive if the
camera has already been added to the screen.
● Authentication: Enter the necessary camera login
info. This option is inactive for DirectIP™ cameras
because they do not require logins. This option is
inactive for IDIS protocol only if the password is set.
3
2
4
1
Registered
Initial registration
other NVRs
(Registration X)
1 Screen Position/Registration Status: Identifies the
camera’s position in the video display area. A blue
background indicates a camera that is available for
registration. A gray background indicates an already
registered camera. Other registered cameras are
shown in black background.
2 Model: Indicates the camera’s model.
3 MAC: Displays the 12 digits of the camera’s MAC
address.
4 Title: Indicates the camera’s name. Changing a
camera’s name in the video display area updates the
camera list as well.
• Select Model and MAC to sort in ascending/
descending order. The registered cameras are
displayed at the top of the list.
• Selecting Title changes MAC address to IP and IP
address changes to MAC.
17
Part 1 - Getting Started
Video Display Area
Left-click on the video display area to toggle between
split screen and single screen modes.
Drag the camera screens around to rearrange them.
• Information is not indicated on the bottom of the
screen for cameras already registered to the NVR,
and the Screen Position/Registration Info icon is
shown with a black background.
• Screen Position/Registration Info icon for cameras
registered to another NVR is shown with a steady
orange background on top of a gray screen.
4 Bitrate Allocation
Indicates the performance (bitrate) allocated to the
channel. Left-click on the upper right corner of the
screen to change the bitrate.
Camera Screen
1
Camera Menu
4
Right-click on the video display area to bring up the
camera menu.
Registered
Registered
2
3
1 Camera Title
Indicates the camera’s title. Left-click on the title to
edit the camera’s title.
● Remove Camera: Removes the registered camera.
● Remove Device: Removes the registered encoder.
● Color Control: Adjusts the camera’s color settings.
● Information: Displays the camera’s basic information.
● Title: Edits the camera’s title.
● Bitrates: Changes the bitrate allocated to the channel.
● Remove All Cameras: Removes all registered
cameras.
2 MAC Address
Camera’s model and MAC address are shown if the
camera has not been registered to the NVR.
3 Screen Position/Registration Info
Flashes in orange if the camera has not been
registered to the NVR.
18
You can drag & drop to add or remove cameras.
Part 1 - Getting Started
Apply/Cancel Buttons
While in Camera Registration mode, select Apply
to register all changes. When selecting Apply, the
following message will be displayed. You can activate or
deactivate Self-diagnosis.
Diagnosis Process
When the camera is registered to the NVR, Selfdiagnosis runs automatically for the new registered
and changed cameras. If Self-diagnosis is processing,
Diagnosis Processing message will be displayed.
Select Cancel to exit Camera Registration mode without
applying the changes.
It is not possible to register a camera that has already
been registered to a different NVR.
If Self-diagnosis is failed, Diagnosis Required message
will be displayed. In this case, you can run Selfdiagnosis manually.
19
Part 1 - Getting Started
Camera Registration Mode
While in Live mode, right-click and select Camera
Registration.
Login
Configuring the NVR’s settings and accessing its
searching and other functions require an authorized
user login.
1
Bring up the Live menu and click on
the mouse to log in.
2
Select a user, enter the password, and then select
OK.
icon using
button next to the password
• Click on the
field using the mouse. This will bring up a virtual
keyboard you can use to assign a password. For
more information on using the virtual keyboard,
refer to the Text Input via Virtual Keyboard on
page 30.
3
20
To log out, bring up the Live menu and click on
icon using the mouse.
Part 1 - Getting Started
Find Password
3
Enter an UPR(User Password Reset) verification and
then click on UPR Verification button.
4
Select the UPR file and then click on Import button.
If you do not know the password, select FIND PW . You
can set a new password.
1
2
Enter a user, registered email and then select Get
Verification Code.
Enter Verification Code and select OK.
• To use UPR function, the UPR file must be saved
in advance. For more information on saving the
UPR file, refer to User on page 33.
• You can reset the password using an encrypted
UPR (User Password Reset; filename extension *
.upr) file.
• It can be used as USB flash driver on local pc,
but not remotely.
• Only files exported from the same device are
available.
• Select the question mark button at the bottom
left corner of the screen to refer to the password
settings instructions.
• The password must be entered only with the
virtual keyboard.
• FEN service must be enabled to use Find
Password function.
• If you lose the UPR file and change the password
of the NVR, the UPR file may not be used.
5
To set a new password, click the question mark
button in the lower left corner and follow the
instructions.
21
Part 1 - Getting Started
Live Mode
Live Menu
Placing the mouse pointer near the top portion of the screen displays the Live menu.
2
1
3 4
5 6 7
8 9 0
! @
^
#
1
Login/Logout
2
Layout
3
Previous Group,
Next Group
4
Display
5
Freeze
6
Panic Recording
7
Sequence
8
Status
9
Select Camera
0
Search Mode
!
Setup
@
Wizard
#
Status Indication
22
Part 1 - Getting Started
1 Login/Logout
Log into and out from accounts. If in the logged in
state, the account ID is shown. If in the logged out
state, the login icon is shown.
2 Layout
Used to change the screen layout to single screen,
1x2, corridor format(1x3) or 2x2.
Corridor Format: Divides the screen into 3 panes.
This format displays vertically and is set to display
the optimized video of the camera when using the
camera’s pivot feature. This is particularly effective when
monitoring hallways, passages, and other confined
spaces.
3 Previous/Next Group
Loads the previous/next screen group.
4 Display
● Full Screen On/Off: Enables the full screen mode.
● Camera OSD On/Off: Enables/ disables the camera
OSD feature.
● Status OSD On/Off: Enables/ disables the status
OSD feature.
● Aspect Ratio On/Off: Setting On displays video on
the camera screen in its original ratio.
Cameo Sequence
In Cameo Sequence mode, only the bottom right
screen in a split screen setup changes sequence. In order
to use the Cameo Sequence feature, Cameo Sequence
(Display Setup - Main Monitor > Sequence) must first be
enabled.
e.g.) Cameo Sequence in 2x2 split screen mode
1 2
3 4
1 2
3 5
1 2
3 6
1 2
3 15
1 2
3 16
1 2
3 4
• If using the Full Sequence setting, page numbers
appear on the system status area on the upper right
part of the screen, next to the Sequence icon.
• If using the Cameo Sequence setting, pages are
skipped under the following circumstances:
– If all cameras included in the page are
deactivated.
– If there are no video signals.
– If the page contains "covert" cameras.
– If the user does not have permission to view
feeds from the cameras.
5 Freeze
Freezes the screen. Select Freeze again to unfreeze.
6 Panic Recording
Activates/deactivates Panic Recording.
7 Sequence
while in Live mode
Selecting the Sequence icon
changes to the sequence mode. To exit, select
3 4
2 Sequence
6more.
78
0
! @
icon 5
once
The 9
icon
is displayed
the upper right part of the screen while Sequence
3 4 on
5
6 78 9 0 ! @
is in
progress.
#
#
Full Sequence
Displays all channels in sequence while in Live mode
(single and split screen settings). In order to use the Full
Sequence feature, Full Sequence (Display Setup - Main
Monitor > Sequence) must first be enabled.
e.g.) Full Sequence in 2x2 split screen mode
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
1 2
3 4
23
Part 1 - Getting Started
8 Status
Displays the status window for NVR's system and
device.
9 Select Camera
Displays the selected camera in a single screen
format.
0 Search Mode
● Time-Lapse Search: Select Search Mode > TimeLapse Search to search for and play back saved
data directly from the record table.
● Event Log Search: Select Search Mode > Event
Log Search to search for event logs and play back
associated event recordings.
! Setup
Used to access the Setup menu.
@ Wizard
Launches the Setup Wizard.
Running the Wizard lets you configure basic settings
required for operating the system.
# Status Indication
Displays system status icons.
Status Indication
Indicates connection to the NVR from a
remote program.
While in Live mode, right-click and select Zoom.
When a zoom frame appears on the selected channel,
right-click on the mouse to zoom in. Use the arrow
buttons to position the frame. When Zoom is activated,
icon is on the status bar located on the upper right
corner of the system.
• In Full Screen mode, activating Zoom automatically
selects the current channel.
• To restore the channel to normal size, press the
Zoom button again.
PTZ Control
While in Live mode, right-click and select PTZ from the
context menu.
The
icon will begin to flash on the selected camera’s
OSD window.
You can change the direction by dragging on the
mouse.
Also, it’s possible to use the mouse wheel to zoom in/
out.
You can change the direction by dragging on the mouse.
Also, it’s possible to use the mouse wheel to zoom in/
out.
Indicates Freeze is in use.
• Logging in with an account that has PTZ Control
Authority is necessary in order to control PTZ
cameras.
Indicates Sequence is in use.
• A message will prompt if there is no PTZ camera
displayed on the Live screen.
Indicates an event monitoring.
• To exit PTZ mode, press the PTZ button of Context
menu again.
Indicates a zoomed in state.
Indicates HDD use. The icon to the left
is shown if using the overwrite setting.
Otherwise, remaining HDD space is shown as
a percentage value.
24
Zoom
Part 1 - Getting Started
Setting Up a PTZ Preset
Advanced Settings
While in PTZ mode, select the
icon to display the
Set Preset window and assign the current position as a
desired preset number .
In PTZ mode, selecting a camera and then right-clicking
on the mouse loads the Advanced PTZ screen as shown
below. This menu lists Speed, Auto Pan, and other
advanced PTZ camera control options available for the
camera. Also selecting Point Move button moves PTZ
camera to the point that the user clicks. Options that
are not available for the selected PTZ camera remain
inactive.
While in PTZ mode, select the
icon to display the
Move to Preset window.
Select a preset number to move the current PTZ camera
to the selected preset’s position.
You can use the mouse to control PTZ cameras. Leftclick on the mouse and drag to move the camera in the
desired direction and use the mouse wheel to zoom
in/out.
While in PTZ mode, place the mouse pointer close to
the bottom edge of the screen to display the PTZ Tools
window.
PTZ Camera Pan and Tilt
Zoom In/Out
Focus Near / Far
IRIS Open / Close
One Push
Set / Move to Preset
Device Menu supported
by the camera
25
Part 1 - Getting Started
• The exact PTZ protocol supported by the camera
must be specified in order to use the NVR's PTZ
controls.
• Drag and drop to reposition the PTZ Tools window.
• Select the
icon to hide the PTZ Tools window.
Event Monitoring
When an event occurs, the NVR automatically changes to
the camera screen linking event monitoring and shows
the
icon on the system status area on the upper
right portion of the screen. To use the Event Monitoring
feature, navigate to Display Setup > Main Monitor and
enable Event Monitoring. Event Monitoring remains
in effect throughout the entire Linked Time. After that,
the NVR will return to the previous screen if a new event
does not take place. Pressing the Layout or a Camera
button before the end of the Linked Time reverts the
system to Live mode.
Covert Camera
Use this feature to assign Covert Camera View
permissions.
Navigate to Camera Setup > General and designate
cameras as Covert 1 or Covert 2.
● Covert 1: Hides images from the camera in Live mode
but does indicate the camera’s title and status via
icons.
● Covert 2: The camera is indicated as being inactive.
Images from the camera are not shown. Camera title
and status icons are not shown.
Users that have a cover Covert Camera View are
able to view both images from and status icons
for all Covert 1 and Covert 2 cameras.
Context Menu Access
While in Live mode, right-click on the mouse to display
the Context Menu window.
● PTZ: Access PTZ controls.
● Zoom: Zoom in.
● Color Control: Select a channel to display its Color
Control window. Adjust the selected camera’s
brightness, contrast, saturation, and hue settings.
● Self-Adjusting Video Mode : Select the image preset
(Natural, Vivid, Noise Reduction) and you can control it
directly.
● Information: Select a network channel to display
information about the selected channel’s device.
● Edit Group: Rearrange the split screen layout.
● Camera Registration: Activate Camera Registration
mode.
● Login/Logout: Log into the account or log out of the
account.
26
Part 1 - Getting Started
Edit Group
Edit Group lets you customize split screen pages in both
Live and Search modes.
1
2
3
While displaying a split screen page, select the Edit
Group option from the context menu. A yellow
border is drawn around the page. Use the mouse to
select a different page.
Right-click on the mouse to select a camera on the
screen with yellow lines. Selected camera is then
loaded on to the selected page. Repeat to assign
other channels to the page.
Right-click on the mouse to exit Edit Group.
Alternatively, press the Menu button and then select
Exit Group Edit to exit.
Edit Group will terminate automatically after 15
seconds of inactivity.
Video Recording
Video recording will only take place if all the connections
are made correctly as per information contained in Part
2 of this operation manual.
For more information on video recording settings, refer
to the Record Setup on page 52.
Panic Recording
Select Live or Search menu’s Panic Recording
icon to
commence panic recording on all registered cameras.
To stop Panic Recording, select the Panic Recording
icon again. If the Panic Recording Duration option
under Record Setup > General has been configured,
Panic Recording will automatically terminate after
the specified duration of time has elapsed. For more
information, refer to the Record Setup on page 52.
• Panic Recording takes place irrespective of any
recording schedule set up by the user.
• Panic Recording video profile from Record Setup –
General applies to all Panic Recording videos.
Panic Recording will not take place if recording mode
is not set to Recycle and the HDD has reached 100% of
its capacity.
27
Part 1 - Getting Started
Video Recording Playback
You can play back video recordings by using mouse.
• Login with an account that has search permission is
needed to playback video recordings.
• The initial video playback point in Search mode is
the recording's last playback point or the end of the
recording data.
• Covert protection on cameras also applies to video
recording playback.
All Channel Playback
1
Place the mouse pointer near the top portion of the
screen.
2
Select the Search Mode icon and then select
Time-Lapse Search or Event Log Search.
3
The selected search mode will be initiated.
For more information on data search, refer to the Part 3 Search on page 79.
28
Part 2 - Configuration
Menu Use
Information contained in this section (Menu Use)
applies to all other instructions found throughout Part
3 - Configuration.
Menu Icon
1
While in Live mode, select Live menu > Setup using
the mouse.
1
2
3
4
5
6
7
8
Use the virtual keyboard to enter text.
Type the text.
X
1
System Setup
Open a drop-down menu.
2
Camera Setup
Delete the item.
3
Record Setup
Change the order of table entries.
4
Event Setup
5
Network Setup
6
Notification Setup
7
Display Setup
8
Status Setup
Change the range of values.
Add new items or works.
Indicate that there are predefined items for
convenience.
Display the submenu or pop-up window.
(except for information, error and alert
windows)
Login with an ID that has permission to access the setup
menu is needed to access and make changes to the
Setup menu.
When using Use 2FA feature, registered mobile device
must be authenticated before entering the setup
menu. For more information on 2FA function, refer to
Use 2FA on page 36.
2
Left-click on the option using the mouse.
3
Change the setting and then select Apply or OK to
save the change.
To apply default settings, select the Default button
located on the left bottom corner of the setup window.
29
Part 2 - Configuration
Text Input via Virtual Keyboard
Click on the key using the mouse.
Batch Assignment
Certain table-format menus such as the shown in the
Camera Setup on page 40 allow you to change
the title value. In this case, changing the title value
simultaneously changes all other entry values on the
same row.
Mouse
Toggle case.
Deletes the character to the left of the cursor.
Deletes the character to the right of the
cursor.
Converts keyboard.
30
Using a mouse makes it easier to configure the settings.
A mouse lets you make selections faster and use its
wheel to scroll through long menus. You can also use
the mouse wheel to increase/decrease numerical values.
Part 2 - Configuration
System Setup
Refer to the Menu Use on page 29 for basic
information on using the Setup menus.
● Import: Decide whether to import network settings
as well. If you do not wish to change the current
network settings, do not select Include Network
Setup.
Selecting Setup Import does not change the settings
below.
General
This Setup menu contains general system options.
• Time-related settings (Date/Time, Time Zone, and
Use Daylight Saving Time)
• Camera-related Advanced Settings settings
• Camera-related Stream settings (Only if the
resolution is different from the camera in exporting)
If users and groups are deleted, existing user settings
are retained.
● Export: Exports the current system settings to a
storage device connected to the system’s USB port.
You can designate a File Name for the export file.
● Site: Used to enter a description about the system’s
installation site (no description by default). You can
edit the information using the virtual keyboard.
● System ID: Used to identify the NVR apart from other
NVRs.
The default System ID is 0 and can be changed to a
value between 0 and 99. The System ID can also be
entered using the virtual keyboard.
For USB flash memory devices, the NVR supports the
FAT32 file format only.
● Show System Log: Displays a searchable list of 5,000
most recent system log entries. For more information
on types of system log entries, refer to the System
icon
Log Types in the installation manual. The
appears next to log entries originating from a remote
source. To export the system log, select the Export
at the bottom of the screen and then designate a file
name.
● Language: Choose a language.
● Version: Indicates the software version.
● Upgrade: Upgrade the system. Selecting the USB
port displays the USB search window. You will then be
able to select an upgrade package and upgrade the
system. Once the upgrade is completed, the NVR will
reboot automatically.
When using Use 2FA feature, registered mobile device
must be authenticated to upgrade the system. For
more information on 2FA function, refer to Use 2FA
on page 36.
● Setup: Exports current NVR settings or imports
existing settings.
31
Part 2 - Configuration
Date/Time
In order to display the system_log.txt file, you must
use the correct character encoding settings and use a
fixed-width font.
● Clear All Data: Erases all recording data. Selecting
Clear All Data displays a confirmation window. Select
Clear to proceed.
• Before you perform Clear All Data, make sure you
are not accidentally deleting important data. Erased
data cannot be recovered.
• Clear All Data does not affect the system log.
Instead, the Clear All Data event will be added to
the log.
● System Shutdown: Shuts down the system. When
prompted, select System Shutdown.
● Date: Used to change the system’s date setting.
● Time: Used to change the system’s time setting.
● Date Format/Time Format: Used to change the
system’s date and time formats.
● Time Zone: Used to designate the system’s time zone.
Refer to the map displayed on the screen and change
the time zone using the mouse or the arrow buttons.
● Use Daylight Saving Time: Enables DST correction.
● Time Sync.: Select a time server for the system to
synchronize with.
● Troubleshooting Reporting: When there is a
problem with NVR system, generate reports for
troubleshooting.
1
Select Automatic Sync.
2
Enter the Time Server’s IP address or domain name
or select and then choose a server from the list of
registered time servers.
3
Specify the server synchronization Interval.
4
Select OK to apply and exit.
• If you have configured the DNS Server setting under
Network - WAN, you can enter the time server's
domain name instead of its IP address.
32
Part 2 - Configuration
● Holiday: Designate holidays. On specified holidays,
recording takes place according to the holiday
recording schedule specified under Record Schedule.
1
Select the + button at the bottom of the window.
2
Select a date.
3
Select OK to apply and exit.
Select the
User
Use this option to register users and assign permissions.
1
Select + Group and enter a group name. A group
name can be up to 15 characters in length.
2
Specify the group’s permission settings. For more
information on permission settings, refer to the
Group Permissions on page 34.
3
Select + User and then enter a user name.
icon to delete the existing holiday date.
33
Part 2 - Configuration
4
5
Select a group for the user and then enter a
password. The password can be up to 16 characters
in length and may include letters, symbols, and
numbers. The e-mail address will be used as
information on password verification.
Select the Export button to create the UPR(User
Password Reset) file. The UPR file can be used to
finding a password offline. Select the location to
save the UPR file and enter the file name.
Group Permissions
System Shutdown
May shutdown the
system from the
system menu.
Upgrade
May upgrade the
system from the
system menu (System
Setup).
Color Control
May adjust each
camera's brightness,
contrast, saturation,
and hue settings.
System Check
May view System
Check results.
6
Select OK.
7
Configure Auto Login and Auto Logout settings.
PTZ(Dewarping)
Control
May control PTZ and
Dewarping cameras.
8
Select Apply or OK to exit.
Covert Camera View
May access covert
cameras in Live and
Search modes.
Factory Reset (NVR)
May reset the NVR to
all its initial factory
settings.
Search
The user who has
permission for Clip
Copy can perform
Clip Copy. If the
user does not have
permission, Clip Copy
is not allowed but only
search is allowed.
• Group names, user names, passwords and email
can be entered using the virtual keyboard. For more
information on using the virtual keyboard, refer to
the Text Input via Virtual Keyboard on page 30
• To delete a registered user or group, select the
icon on the right of the corresponding user/group.
Group Administrator and User admin cannot be
deleted.
• Select the
icon next to Group & User on the
top of the screen to delete all groups and users
except Group Administrator and User admin
simultaneously.
• A password entry is required to edit existing groups
and users.
• Group Administrator's permissions cannot be
changed.
• With the User admin account, only the password
can be changed.
• When the system starts up, it will automatically log
into the account designated under Auto Login.
• The system will automatically log out of the account
if the duration of inactivity specified under Auto
Logout.
34
Clip Copy
Part 2 - Configuration
Setup
Camera Setup
May configure camera
settings.
System Time
Change
May change the
system's date and time
settings.
Data Clear
May clear data stored
in the system.
PTZ Setup
May configure PTZ
settings.
May configure convert
Covert
Camera Setup camera settings.
Record Setup
May configure
recording settings.
SelfDiagnosis
May configure the
NVR self-diagnostic
settings.
Setup Import
May import previously
saved NVR settings.
Setup Export
May export current
NVR settings.
Remote Connection Policy
Camera Is Hidden
Schedule
Select camera channels to
hide on the screen when
connecting remotely.
Select Schedule On and
then configure the days
of the week and remote
connection interval. If not
selecting Schedule On,
remote connection is allowed
regardless of scheduled
intervals.
Auto
Expiration
Select Enable to set
whether the auto-expiration
period works. You can set
the retention time when
connecting to the NVR from a
remote location.
Waiting
Period
Select the limit time for
access after automatic
expiration.
Use
35
Part 2 - Configuration
Security
Use this option to configure security settings.
If you click the + button at the bottom of the table, the
following message will appear and you can register the
2FA device.
• 2FA device registration is supported only via IDIS
Mobile app.
Use 2FA
• Only the administrator account user can configure
this option.
Two-factor authentication (2FA) is a method of
confirming a user's claimed identity by utilizing a
combination of two different components.
In other words, it is a method of authenticating the
registered mobile devices such as mobile phones and
smartphones on NVR for security when proceeding
settings, search and upgrade.
• The maximum number of device that can be
registered is 16.
When the mobile device registration is complete, the
following message will appear. Click Disable 2FA at
the bottom left corner of the screen to deactivate 2FA
function via the email of an administrator user account.
When you click Use 2FA and 2FA Setup buttons,
the following window will appear (Registered means
the time when the mobile device was registered).
To use email authentication, the FEN setup must be
configured. To use UPR function, the UPR file must be
saved in advance.
For more information on saving the UPR file, refer to
User on page 33.
36
Part 2 - Configuration
Network Security (Host Certificates)
This is the certificate management menu for network
security access. It supports checking the product
certificate information, creating the new certificate,
exporting and importing certificates.
Storage
Use this option to configure storage settings.
● Type: Indicates the type of the installed disk.
● Capacity: Indicates the disk’s capacity.
● Format: If the disk has been formatted, indicates
either Record or Not Using. If you have connected an
unformatted storage device, the Use As value will be
indicated as Not Formatted.
● Information: Indicates if the disk is being used for
recording purposes. Disks that were used in different
systems will show up as Other. Select Information
to check the saved data’s time information or select
Delete to erase the data.
• Select Format to prepare the disk as a storage for
data recording.
• Disks formatted with Use As set to Not Using will
not be used for data recording.
• This NVR supports SATA2 HDDs.
37
Part 2 - Configuration
Self-Diagnosis
Use this option to configure self-diagnostic settings.
This feature is also supported when connected to the
NVR from a remote program.
• The reports are stored in up to 24 files. If you have
configured Auto Generating Interval as one-day
period, only the the reports from the last 24 days
can be viewed.
• If the NVR is turned off, the reports will
automatically turn off.
• The reports are organized by recent date and time.
● FailOver: When a problem is detected on the target
device, click the Run the failover button to resolve
the problem.
● Reports
– No.: Selects which reports to export.
– Time: Displays when you started the self-diagnosis.
– View a Report: Briefly displays whether the report
is “Good” or “Bad”.
–
: Click the + icon at the bottom left corner of
the screen to run the self-diagnosis.
– Export: Saves the Saves the reports to a storage
device (USB port), by converting them to HTML
format. You can export more than one report at a
time by selecting multiple reports.
● Set up Auto Generating Interval and Check IP
Duplicate.
– Auto Generating Interval: Set the interval to
automatically generate self-diagnosis report.
– Check IP Duplicate: Check if there are IP address
conflicts of WAN, VIN, camera.
• These settings can be periodically checked for IP
duplication, but Camera IP duplication checks have
a long verification cycle, so you can run a selfdiagnosis to check the results immediately .
• Check IP duplicate function can only be checked on
the VIN network.
38
– Target Device.: Selects which device to run the
failover.
– Channels: Select the camera channel if a camera is
set to the target device.
– Action: Select the type of action to run the failover.
– Run the failover: Click the Run the failover
button when a fail is detected on the target device
to resolve the problem.
Once Run the failover have made to the camera, the
camera will reboot automatically.
Once you have run failover on the camera, the camera
will reboot automatically. By selecting System,
Network, Device Health Status, Storage Status or
Camera Status, you can see the brief results of the selfdiagnosis for the target device.
The NVR self-diagnostic report can only be viewed in
text form.
This feature is also supported when connected to the
NVR from a remote program.
We recommend clicking the Export button at the
bottom of the list, which allows you to view the reports
on a PC web browser. We also recommend scanning
the self-diagnostic report on a remote program, which
allows you to view the reports in HTML format as shown
below.
Part 2 - Configuration
Custom Value
● Name: Set the name of system properties to be
included in a JSON file on HTTP notifications.
● Value: Set the value of system properties to be
included in a JSON file on HTTP notifications.
About
● User Agreement: User agreement for the use of
the FEN service. If you agree, we collect device
information such as IP address, port and router
information to the FEN server.
39
Part 2 - Configuration
Camera Setup
Refer to the Menu Use on page 29 for basic
information on using the Setup menus.
Device Scan
Scan the device under Registration - Scan.
Registration
You can register cameras at remote locales. By selecting
a number from the list, you can move the camera up
or down the list using the mouse wheel to reorder its
position. The remaining cameras will move down the list
automatically.
● Protocol: Select the protocol you wish to search for
that was used by the camera (or encoder).
• Even if the network device uses a protocol
supported by the NVR, the device itself may not be
visible for scanning and registration by the NVR. For
more information about supported network devices
and models, contact your retailer.
• The supported scan modes may vary depending on
protocol selected.
● Title: Edit the camera’s name.
● MAC Address: Displays the camera’s MAC address
registered to the NVR.
● Address: Displays the camera’s IP address registered
to the NVR.
● Model: Indicates the camera’s model.
● Bitrate: Changes the bitrate allocated to the channel.
● Scan: Select to scan and register the device
connected to the NVR.
This feature is supported only when connected to the
NVR from a remote program.
● Mode: Select the scan mode.
– Auto Scan(LAN): Lists any cameras in a LAN
environment. If Auto scan (LAN) fails to recognize
the camera, try using IP Address scan instead.
– IP Address: Enter the IP address of a camera.
The NVR scans for the camera that matches the
specified address. If you enter an IP address
range, the NVR scans for cameras falling under
the specified address range. By specifying an IP
address, you can also specify which port to use
with the Remote Admin feature. It is recommended
that you do not network the camera via DHCP
(Dynamic Host Configuration Protocol). If the
camera is networked via DHCP, the camera may
not be connected properly depending on changes
in the external network environment.
If Auto Scan (LAN) fails to recognize a camera, try using
the IP Address scan instead.
40
Part 2 - Configuration
● Filter: Enter a keyword in the MAC Address / Address
/ Model / Name / Status fields for the selected camera.
This allows the user to scan this camera easily.
• When configuring a port, the device may fail to
scan if the port selected for the NVR and the port
selected for the camera differ. In this case, you must
register the camera to change its IP address.
• The device to be registered must have different IP
addresses. Otherwise, the connection may fail.
● No.: Select the registered camera number and click
the Add Camera button to register the camera.
● MAC Address: Displays the scanned camera’s MAC
address.
Login
If the password is set or you want to register third party
cameras, registering a device requires an authorized
user login.
1
Select the desired deivce from the list and click the
Add Camera button, then the login window will
appear.
2
Select a user, enter the password, and then select
OK.
● Address: Displays the scanned camera’s IP address.
● Model: Indicates the camera model.
● Protocol: Indicates the scanned camera’s protocol.
● Name: Displays the scanned camera’s IP name.
● Status: The “Registered” indicates the camera is
registered to the NVR and “Not registered” indicates
the camera is not registered to the NVR.
• By selecting Apply to All Devices, you can apply
the same authentication information to all of the
network devices in the list.
• When you select multiple network devices from the
list and click the Add camera button, a window for
the network device will appear. Select Skip to skip
the authentication settings for the current network
device and to display the Authentication window of
the next network device.
• For IDIS cameras, a user and password may not be
required.
41
Part 2 - Configuration
Set Camera Password
For IDIS protocol cameras that support changing and
finding the camera password, you must set the camera
password at the time of initial camera registration. The
email information is used to change and find the camera
password.
1
General
Enable/disable the covert view and rename cameras.
Select the dedeivce from the list and click the Add
Camera button, then Set Password window will
appear.
● Title: Edit the camera’s name.
● Use: Set the camera as Normal, Covert 1, or Covert 2.
Only the camera that does not set password of the
camera which supports the password setting function
is displayed.
2
Enter the password and e-mail address, and then
select OK.
• If you do not authenticate your email address, you
may not be able to find your password unless you
enter the correct information.
• FEN setup is required for authentication.
• By selecting Apply to All Devices, you can apply
the same password and e-mail information to
cameras that require password settings in the scan
list.
• When you select multiple network devices from the
list and click the Add camera button, a window for
the network device will appear. Select Skip to skip
the authentication settings for the current network
device and to display the Authentication window of
the next network device.
3
42
When the password is set, the login window will
appear.
Live images and video recordings from cameras that
have been set as Covert 1 or Covert 2 will not be
available to users who do not have covert camera
access. Setting a camera as Covert 1 hides its images
but does display OSD information about the camera.
Setting a camera as Covert 2 hides its images as well
as ODS information about the camera as if it has been
deactivated completely.
Part 2 - Configuration
Advanced Setup
Configure security and other advanced camera settings.
1
2
3
4
5
6
7
8
9
0
!
@
Numbers shown below Preset, Scan, Pattern, and Tour
indicate the numbers of configured functions.
● Video: Adjust the camera image sensor settings such
as white balance and exposure. Configuration options
may differ depending on the camera model.
1 Preset
● Privacy Masking: Enable/disable and configure
privacy masking for the camera.
● SSL: Set the camera’s security level as Unavailable,
Standard, High, or Very High. Standard, High and
Very High settings apply SSL (Secure Sockets Layer)
protection to the camera.
The more cameras security level is set to Very High,
the more the device loads may occur due to the
decoding of received data such as video and audio.
This may cause the total recording performance to
decrease and not work as you set it to. In this case,
you must improve the load by lowering the security
level or by lowering the recording bitrate.
● Reset: Resets the port or cameras.
– Factory Reset : Control the PoE Switch’s port. This
option is available when connecting to Video In/
PoE port or using a DirectIP™ PoE Switch (optional).
Select PoE Reset to reboot the camera. It is not
supported by video encoders.
– Soft Reset : Reboots the camera.
– Factory Reset : Resets the NVR to all its initial
factory settings. It is supported by DirectIP™
cameras only.
Use the buttons below to choose a preset position.
– Directional Buttons (
):
Used to tilt and pan the camera.
– Zoom (
): Zoom in and out.
– Focus (
): Adjust camera focus to far or near.
– Speed: Specify the camera’s panning and tilting
speed.
● Set: Choose a preset number and then enter a name.
This saves the current preset under the specified
preset number and name.
● Go to: Select a preset from the list and then click Go
to to move the camera to the selected preset position.
● Edit: Used to change the selected preset’s name.
● Remove: Used to remove the selected preset.
43
Part 2 - Configuration
2 Scan
Used to set up a profile for moving the camera between
two points. At least two presets must be available in
order to use the scan feature.
Used to tilt and pan the camera.
– Zoom (
): Zoom in and out.
– Focus (
): Adjust camera focus to far or near.
– Speed: Specify the camera’s panning and tilting
speed.
● Test: Select a pattern profile and then click Test to test
it.
● Edit: Used to edit the selected pattern profile.
● Remove: Used to remove the selected pattern profile.
Set: Used to set up a scan profile.
4 Tour
Used to set up a tour profile of multiple functions in a
designated sequence.
– Name: Enter a name for the scan profile.
– Start/Stop: Specify which presets to use as start
and stop points.
– Dwell Time (sec.): Specify how long the camera will
dwell at start and stop positions.
Set: Used to set up a tour profile.
– Speed/Direction: Specify scanning speed and
direction.
● Test: Select a scan profile and then click Test to test it.
● Edit: Used to edit the selected scan profile.
● Remove: Used to remove the selected scan profile.
3 Pattern
Used to set up a pattern profile for the camera to follow
along.
– Name: Enter a name for the tour profile.
– Function: Indicates the order of the function in the
tour sequence.
– Dwell Time (sec.): Specify how long to perform the
selected function for.
– Speed: Specify the preset speed.
● Test: Select a tour profile and then click Test to test it.
● Edit: Used to edit the selected tour profile.
● Remove: Used to remove the selected tour profile.
Start recording: Select a pattern number, enter a name
for the pattern, and then click OK to save the pattern.
Move the camera using directional, zoom, and focus
buttons and then click Stop recording to save the
pattern profile. You can record up to two minutes of
movement.
):
– Directional Buttons (
44
Select Apply after setting up a preset, scan,
pattern, or tour profile to see images from the
concerned camera on the left side of the screen.
Selecting Apply or OK displays a popup screen
that indicates whether the profile has been set up
successfully.
Part 2 - Configuration
5 PTZ Reset: Reboots the camera’s panning / tilting
and zoom settings.
Privacy Masking Options
6 Home Position: Specify the camera’s home position.
● Default: Uses the factory-default position as the
camera’s home position.
● Custom: Uses the user-defined position as the
home position.
● Select Set to change the home position.
7 Auto Run: Specify which action to take if the camera
has not been controlled for the specified duration of
time.
8 Auto Pan: Specify the camera’s panning direction.
When Auto Pan is selected from a remote program,
the camera pans in the direction selected here.
9 Auto Flip: Automatically flips the image when the
camera tilts past 90° to prevent the objects from
appearing upside down.
● Digital: Flips the image left to right or top to
bottom.
● Mechanical: Automatically pans or tilts the
camera.
● Off: Disables Auto Flip.
0 Tilt-Range: Specify the camera’s tilting range.
! Restore: Specify whether to restore the camera to
its last position or function. Enabling this option
restores the camera to its last position or function
after being restarted.
Select Name to rename the privacy masking area. Select
the icon to delete the existing privacy masking area.
Select Privacy Masking Setup to display additional
privacy masking area options. You can drag on the area
with the mouse to resize it or add up to 16 different
areas.
● Edit: Rename the selected privacy masking area.
● Delete: Delete the selected privacy masking area.
● Save: Save the changes and exit the privacy masking
area options screen.
● Cancel: Exit the privacy masking area options screen
without saving the changes.
@ Periodic Moving: Operate the PTZ camera at each
operation cycle for the specified schedule period.
45
Part 2 - Configuration
Image Sensor Options
● White LED Mode: Clicking on/off enables or disables
White LED lighting when motion is detected by the
PIR sensor. Also clicking auto allows the system to
enable/disable White LED mode automatically.
● Pivot: Enable this option and choose the direction of
the pivot. You can turn the image by 90 degree in the
clockwise or counterclockwise direction. This feature
is particularly effective when monitoring hallways,
passages, and other confined spaces.
● Defog: Disables or enables the Defog feature. When it
is enabled, image with a fog is adjusted.
● Product, Firmware Version: Displays the camera
model name and firmware version.
● Video Style: Select TV1 Color or PC Color.
● Backlight Compensation: Enable/disable Backlight
Compensation. If enabled, objects are exposed
brighter in backlit situations.
● Auto Adjust: Selecting Auto allows the system to
assess the lighting conditions and adjust the setting
automatically. Selecting Manual allows the user to
adjust the setting manually.
● Sharpness: Adjust the sharpness level. Adjust the
contours to make the images look sharper. Increasing
the value raises the sharpness level, but using too
high a value can result in unwanted noise.
● Noise Filter: Select the noise filter level. Noise filter
can reduce the noise in images taken under lowlighting conditions. Increasing the value reduces the
noise, but using too high a value can result in blurry
images.
● 3DNR : Enable/disable 3DNR (3D Noise Removal).
3DNR reduces background noise in images taken
under low-lighting conditions. 3DNR does not
produce blurry images like Noise Filter but can result
in ghosting.
● Refocus Mode : Readjust the focus of the camera
when changing daytime to nighttime or nighttime to
daytime.
– On/off: Enable/disable Refocus Mode.
– DN Mode Shift: When image of the camera is
switched to daytime or nighttime, the focus of the
camera will be adjusted.
– IR Adaptive Shift: Readjust the focus of the
camera when IR is detected by the camera.
46
● IR Strength: Adjust the IR LED’s brightness level.
Select a brightness level manually between 0%
(darkest) and 100% (brightest). Selecting Auto(Smart
IR) allows the system to control the IR LED's brightness
level automatically.
● Smart IR: Help solve the problem of infrared LEDs
whiting out images, such as people's faces, when they
are too close to the IR LEDs of a night vision camera.
In this case, the image is adjusted through AE control.
● Advanced AE Mode: Select desired setup mode
between Normal and Number-Identification. In
Number-Identification mode, when a certain area
of images is too bright due to backlight under low
lighting conditions and it causes the other area to
be too dark, this function provides the other area of
images brightly and clearly by blocking the backlight
in the certain area. Dark parking lot entrances and
gas station entrances at night, for example (Local
Exposure compensates for the bright light coming
from incoming vehicle headlights and makes it
possible to see the license plates). When setting to
the Number-Identification mode, some option
settings will be adjusted automatically, and you
cannot change them as long as the Setup Mode is not
changed.
● Mirror: Select Horizontal or Vertical to flip the image
horizontally and/or vertically.
Select Apply after setting up a camera to see images
from the concerned camera on the left side of the
screen. Selecting Apply or OK displays a popup screen
that indicates whether the camera has been set up
successfully or not.
Part 2 - Configuration
White Balance Options
Exposure Options
● Preset: Use preconfigured white balance settings.
● AE Target Gain: Specify exposure compensation’s
target gain. Exposure is compensated automatically
based on the specified target gain. Higher the gain,
brighter the images.
– Auto: Allow the system to adjust the white
balance automatically. The system will assess the
lighting conditions and adjust the white balance
automatically.
– Incandescent - Fluorescent Cold: Select a lighting
type to apply the appropriate white balance.
● Manual: Adjust the white balance manually. Adjust
Red and Blue gain values. Greater the value, greater
the intensity of the corresponding color.
Select Apply after setting up a camera to see images
from the concerned camera on the left side of the
screen. Selecting Apply or OK displays a popup screen
that indicates whether the camera has been set up
successfully or not.
● Local Exposure: Activate Local Exposure. Use Local
Exposure on images that appear too dark due to
backlighting conditions and on images containing
over-exposed sections. Greater the value, clearer the
image. e.g.) Dark parking lot entrances and gas station
entrances at night (Local Exposure compensates
for the bright light coming from incoming vehicle
headlights and makes it possible to see the license
plates).
● Anti-Flicker: If the lights in the area where the
camera is located use alternating current, specify
the frequency of the lights to minimize flickering.
Matching the frequencies can eliminate flickering
completely. (NTSC: 60Hz, PAL: 50Hz).
● Slow Shutter: Activate Slow Shutter. The slow shutter
mode functions only under low lighting conditions.
When the slow shutter mode is enabled, images
are displayed bright even under the low-lighting
conditions. There may be a difference in the way it
functions depending on the camera model. See the
camera user’s manual for details.
● Focus Mode: Used to change the focus movement
format as Auto/Manual/Semi-Automatic. It may not
be supported depending on the device.
● WDR: Disables or enables the WDR (Wide Dynamic
Range). When the very dark and very bright areas
exist simultaneously on the screen, WDR allows you to
recognize the both areas.
47
Part 2 - Configuration
● IRIS: Depending on the camera type, the user can
select DC-IRIS or P-IRIS.
Day & Night Options
– DC IRIS
– OFF : Select this if a manual IRIS lens is mounted
on the camera.
– DC-IRIS (Auto) : Select THIS IF A DC-type auto
IRIS lens is mounted.
– P-IRIS
– P-IRIS (Auto) : The system will assess the lighting
conditions and adjust the openness of IRIS
automatically.
– P-IRIS (Fix) : Use the slider to select the desired
openness of IRIS. Select the most suitable value
for the lighting conditions in the area where the
camera is located.
● Exposure Control: Adjust Shutter Speed and Gain.
This option is available only when Anti-Flicker and
Slow Shutter are both set to Off.
– Auto: The system will assess the lighting
conditions and adjust the shutter speed and gain
automatically.
– Manual: Use the slider to select the desired shutter
speed and gain. Select the most suitable minimum
and maximum shutter speeds and gains for the
lighting conditions in the area where the camera is
located. (1/30 to 1/8000)
Select Apply after setting up a camera to see images
from the concerned camera on the left side of the
screen. Selecting Apply or OK displays a popup screen
that indicates whether the camera has been set up
successfully or not.
● Black & White Mode: Display the images in grayscale
for greater clarity in low-lighting conditions.
– On/Off: Enable/disable Black & White Mode.
– Auto: Allow the system to enable/disable Black &
White Mode automatically.
– Schedule: Set up the Black & White Mode
schedule. Black & White Mode is disabled for all
days and times that are designated as Daytime in
the schedule and is enabled at all other times.
● IR Mode: IR Mode blocks out the infrared spectrum.
You can ensure clear images at all times by blocking
out the infrared spectrum in high-lighting conditions
and allowing the infrared spectrum to pass through in
low-lighting conditions.
– Daytime Mode/Nighttime Mode: Enable/disable
IR Mode.
– Auto: Allow the system to enable/disable IR Mode
automatically.
– Schedule: Set up the IR Mode schedule. IR
Mode is disabled for all days and times that are
designated as Daytime in the schedule and is
enabled at all other times.
Some camera models may not support the
Schedule function.
● Switching Mode : Changes the switching mode of
daytime and nighttime. In normal mode, daytime/
nighttime is switched through the amount of light
received by the ambient light sensor. In advanced
mode, it is switched through the amount of light and
the analysis of the camera video.
● Switching Level : Controls the changing time
of daytime / nighttime mode, depending on the
Switching Level. The higher the value is, day /
nighttime mode is changed under high-lighting
conditions. Also the lower the value is, day / nighttime
mode is changed under low-lighting conditions.
48
Part 2 - Configuration
Stream I
View Options
● Type: Selects the camera view.
● Mode: Selects the screen layout in live mode.
• Dewarping feature is not supported when mode is
set to the original.
• When changing the view mode, the resolution will
be applied automatically.
Configure the camera’s live and recording resolution,
codec, picture quality, transfer speed, and ips speed
settings.
● Camera Channels: It’s possible to configure a unique
video profile for each camera.
● Bitrate Status: Display the highest value of stream.
Click the Setup button to change the allocation for
each channel. For more information on bitrate, refer
to Camera View Buttons on page 16.
●
Miscellaneous
: Apply the video profile settings of the camera
selected under Camera Channel to a different camera.
● Live/Remote Video Profile: Check the current Live
video picture quality and edit remote video profile
settings.
● Record Video Profile: Set up 4 recording quality
profiles.
● Video Profile: Select Stream 1, Stream 2, Stream 3,
or Custom (available from Record Video Profile only).
– Codec: Supports H.264 and H.265.
– Resolution: Select a resolution supported by the
camera. Maximum available resolution is chosen
automatically based on the selected video profile.
– Quality: Assign different quality settings to
different cameras.
● Image Stabilizer: Activate Image Stabilizer. The
Image Stabilizer reduces blurring caused by camera
shake that results from external conditions such as
the wind.
● Video Out: Select NTSC or PAL as the method of
camera analog video output.
● Heater Mode: Set whether to use the heater. If On,
the heater will operate if the camera’s temperature is
lower than the heater operating temperature. If Off,
the heater will not operate regardless of temperature.
– VBR/CBR: Select VBR or CBR. Transmitted data size
varies depending on the amount of movements in
the images with VBR but is fixed with CBR.
– ips: Select a value between 1 and 30. Maximum ips
is determined automatically based on the selected
video profile.
– Bitrate: Displays the bitrate value of each stream.
The bitrate is determined by the codec, resolution,
quality, and IPS settings. Settings beyond the
channel's assigned bitrate are limited.
49
Part 2 - Configuration
● Use Dual Track Recording: Set to record with the
video profile value (main stream) set in the schedule
and record with the profile 4 value (sub stream) at the
same time.
Stream II
• It displays as below when recording on a network
video recorder.
– The video profile (main stream) set in the
schedule is displayed. If the resolution
exceeds 8M in total, Profile 4 (sub-stream) is
displayed.
– If the total resolution exceeds 8M in 1+5,
1+7 screen layout, Profile 4 (sub-stream) is
displayed.
– If the total resolution does not exceed 8M,
it is displayed as follows. If the channel is
larger than 3x3 size on the screen layout, the
video profile (main stream) is displayed first
but otherwise the profile 4 (sub stream) is
displayed.
• This function is supported only for cameras
supporting dual recording function.
50
Configure the camera’s failover profile, intelligent codec
and MAT settings.
● Failover Profile: Select a video profile for the smart
failover recording.
● Intelligent Codec: Lower bitrate by using the
intelligent codec.
• Some camera models may not support the
Intelligent Codec function.
Part 2 - Configuration
● MAT Setup : Select the MAP Setup option to use the
MAT (Motion Adaptive Transmission) function during
video transmission and recording.
• When the MAT (Motion Adaptive Transmission)
function is active, the associated VA device may
not work properly.
• It is recommended that you do not use the MAT
function of the associated camera to increase the
accuracy of the image analysis.
Maintenance
When the USB search window appears, select the
corresponding upgrade package from the storage
device connected to the NVR’s USB port. After selecting
the upgrade package, select Apply to upgrade the
camera. Camera settings can be imported or exported.
• Some camera models may not support the MAT
function.
* MAT function(Motion Adaptive Transmission)
reduces bandwidth overload and saves storage
capacity by reducing the frame rate of the video
during periods of inactivity. The user can select the
period of sustained inactivity which triggers this
function by adjusting Inactivity Period.
• If an upgrade attempt fails, an upgrade failure
message will be displayed. Refer to Error Code
Types in the installation manual for more details.
• The camera will reboot after the upgrade and then
reconnect automatically.
● Sensitivity : Set the motion detection sensitivity.
Higher values will result in more sensitive motion
detection.
● Inactivity Period : Set the Inactivity Period. If motion
is not detected for the duration of time specified,
video is transmitted and recorded using the frame
rate designated below until movement is detected
again.
● Sensor Mode: Set the camera resolution to 16:9, 4:3.
Depending on the mode you have set, the resolution
that can be set in the stream section changes.
51
Part 2 - Configuration
Record Setup
Refer to the Menu Use on page 29 for basic
information on using the Setup menus.
General
Configure general recording settings.
● Limit Time-Lapse Recording: You can store event
recording data for longer. If you do not wish to use
Limit Time-Lapse Recording, select Never. This
function is activated when data has been stored for
longer than as configured because the recording
disk has sufficient capacity and saves new data by
overwriting Time Lapse Recording data that are
older than as specified under Recycle mode.
• If the recording stored on the disk is shorter than
the duration specified under Limit Time-Lapse
Recording, the older of Event Recording or Time
Recording data is deleted first.
• The system's recording time may change depending
on recording quality, resolution, motion, and other
configurations made by the user. The duration
specified under Limit Time-Lapse Recording may
not be guaranteed in certain situations.
● Recording Failover Service: When the network
error has recovered, images temporarily stored in the
camera's buffer memory can be recorded to NVR.
● Recycle: When the recording disks become full,
the system overwrites existing data with new data,
starting with the oldest first. If Recycle is disabled,
recording will simply stop when the recording disks
reach their maximum capacity.
● Event Record Dwell: If linked recording is designated
as an event-triggered action, recording takes place for
the duration specified under this setting.
● Auto Deletion: Configure this option to delete
recording data automatically after the specified
number of days has elapsed. Select between 1 day
and 999 days.
To disable Auto Deletion, select Never. If enabled,
recording data will be stored on the NVR for
the specified number of days and then deleted
automatically. Expired recording data are deleted
automatically at midnight and will be deleted even if
the system reboots or the Auto Deletion setting has
been changed.
52
● Use Panic Recording: Enable/disable Panic
Recording.
● Panic Recording Duration: Disable Panic Recording
automatically. Select between 5 mins and 1 hr. If you
do not wish to disable the feature automatically,
select No Limit.
● Video Profile: Select a recording profile value for
Panic Recording.
Part 2 - Configuration
Schedule
Simple Mode Options
● Mode: Select No Record, Time, Event, or Time &
Event.
No
Record
Time
<Simple Mode>
Unless the Panic Record button is
pressed, no recording will take place
during the scheduled time frames on the
scheduled days.
icon appears on the upper
The
icon
left corner of the screen. The
appears at scheduled times to indicate
recording is in progress.
icon appears on the upper
The
icon
left corner of the screen. The
appears when the specified event occurs
to indicate recording is in progress.
Event
<Advanced Mode>
Disabling Schedule On suspends schedule recording
regardless of the schedule and displays the
icon on
the upper left corner of each camera screen. Pressing
icon and
the Panic Record button displays the
commences panic recording.
Set Record Schedule mode as Simple Mode or
Advanced Mode. Advanced Mode allows you to
configure a unique recording schedule for each event.
Select the icon to delete a schedule.
• Changing the recording schedule mode suspends
all active event-linked actions.
Time &
Event
If Pre-Event is enabled, the
and
icons appear when recording is
not in progress, or the
and
icons appear when an event occurs
and recording is in progress.
icon appears on the upper left
The
corner of the screen and recording
commences as per the video profile
selected for time under Setup. When
an event occurs, the icon changes into
icon and recording commences as
per the video profile selected for events
under Setup.
● Channel: Select which cameras to apply the schedule
to.
● Settings: Select to configure default recording profile
values for Time Lapse and Event Recording modes.
• Select the + button on the bottom left of the screen
to add a schedule. Select Day to specify the Day
setting or select All. Select Scope to specify the
time frame.
53
Part 2 - Configuration
If a camera supporting the Dual Track Recording
function (Main and Sub stream) is in use, the following
icon will be displayed.
Recording both mainstream and substream
Advanced Mode Options
Select to configure event types and video profiles.
● Type: Event-specific and time recording icons are as
follows:
Recording one of the mainstream and
substream
Time Lapse
(Time)
Trip Zone
Failed to record both mainstream and
substream
Motion
Detection
Tampering
Video Loss
Recording Fail
PIR
Auto Tracking
● Video Profile: Configure the profile to use for
recording.
● Dwell: Specify how long to record for after a
corresponding event occurs.
• Upper-tier schedule's settings apply to
unconfigured channels.
• If multiple events take place on a specific channel
and different Video Profile and Dwell Time settings
apply, highest settings apply to all event-linked
recordings.
54
Part 2 - Configuration
Pre-Event
When an event occurs, enabling this option includes
the specified duration prior to the event in the eventtriggered recording.
Event Setup
Refer to the Menu Use on page 29 for basic
information on using the Setup menus.
System_Event
Use this option to configure system event settings.
● No.: Select which cameras to apply Pre-Event to.
● Video Profile: Select a video profile for the recording.
● Dwell: Specify the duration of pre-event recording
data.
• If no event mode schedule exists in the schedule, a
warning message prompting you to add an event
mode schedule will be displayed.
• The warning message will appear even in Time &
Event mode.
● Settings: Configure when and what the system
should monitor for.
● Actions: Configure notification (email, LAN1 through
5, push, HTTP, alert window) settings.
55
Part 2 - Configuration
Monitoring Options
System
Define monitoring times. If selfdiagnosis is not performed on a
regular basis, the system will assume
an error.
Bootup,
Restart,
Shutdown
Define bootup, restart and
shutdown actions.
Panic Record
Define panic recording actions.
The system will assume an error if
the system has been scheduled to
record normally but recording does
not take place during scheduled
intervals.
Check
Recording
Select Schedule On and then
configure the days of the week,
times, and monitoring interval.
Select the button on the
bottom left of the screen to add
a schedule. Select
icon to
delete the schedule.
Disk
S.M.A.R.T.
Monitors disks that support
S.M.A.R.T. and notifies the user if a
disk error is detected.
Disk Config
Change
It will be highlighted when the NVR
reboots after the hard disk drive has
been replaced.
No Storage
Found
It will be highlighted when no hard
disk drive has been connected.
Consecutive
Invalid PW
It will be highlighted when login
fails by entering a wrong password
for consecutive attempts.
• For system events, only an e-mail notification of
actions can be selected.
• In order to use the Notify(Callback) feature, the
NVR must be registered to the remote program on
the receiving PC's end.
Camera System
A list of events that occur in the camera except for video
analysis.
Disk Almost
Full
Generates an event if the disk
reaches the specified capacity (80%
to 99%).
Disk Full
Generates an event when all disks
reach their maximum capacity.
Disk Bad
Generates an event when the
specified percentage of the disk
becomes damaged. Set to between
10% and 90% in 10% intervals.
Disk
Temperature
Specify the threshold temperature.
Once any disk reaches this threshold,
the system will issue an alert.
56
Part 2 - Configuration
Camera System_Video Loss
Camera System_Recording Fail
● Activation Time: Specify how long video loss has
to last in order for it to be considered as an event.
When the video loss is not detected for the specified
duration of time, it will not be considered as an event.
● Activation Time: Specify how long recording fail has
to last in order for it to be considered as an event.
When the recording fail is not detected for the
● Actions: Specify which actions to take when a Video
Loss event occurs.
● Actions: Specify which actions to take when a
Recording Fail event occurs.
● an event.
– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
– Notify: Configure to be notified of events by Mail,
LAN1 through 5, Push, HTTP, and/or Alert Window.
– Notify: Configure to be notified of events by Mail,
LAN1 through 5, Push, HTTP, and/or Alert Window.
– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
– Event Monitoring: Selects the cameras to monitor
when an event occurs.
– Event Monitoring: Selects the cameras to monitor
when an event occurs.
In order to use the Callback feature, the NVR must be
registered on the remote program.
In order to use the Callback feature, the NVR must
be registered on the remote program.
57
Part 2 - Configuration
Camera System_PIR
This event occurs when the PIR sensor mounted on the
camera is used to sense motion. Since the PIR sensor
detects the temperature of the human, it can detect
motion even in dark places without light.
● No.: Select which cameras to apply PIR to.
● Sensitivity: Set sensitivity settings between 1 (Low)
and 5 (High).
● Reference Event: Set condition for event to occur
using the PIR sensor. A PIR event occurs when a
motion occurs after an event set as a reference event
has occurred. You can set Motion and Trip Zone as
● Ignore Condition
– Ignoring Interval: The system does not produce
event log entries or remote notifications for events
detected within a certain period of time after PIR
events of the camera channels are detected. Set the
value between 1 sec and 5 secs or choose Never.
Ignoring interval setting does not affect the
motion detection recording.
58
– Use Ignoring Time: Select Time Setup to specify
the PIR detection ignore time of camera channels.
PIR detection will be disabled during the specified
time frame.
● Actions: Specify which actions to take when a PIR
event occurs.
– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
– Notify: Configure to be notified of events by Mail,
LAN1 through 5, Push, FTP, and/or Alert Window.
– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
– Event Monitoring: Selects the cameras to monitor
when an event occurs.
Part 2 - Configuration
Video-Analytics
Event lists that occur through video analysis include
Motion, Tampering, PIR, TripZone, Face Detection and
Auto Tracking events..
button
From the zone selection screen, press the
on the remote control or right-click on the mouse to
open up the Zone Setup menu.
– Select: Confirm the block selection in the selection
window.
– Clear: Clear the block selection in the selection
window.
– Reverse: Clear the blocks selected within the
selection window and select all unselected blocks
within the selection window.
Video-Analytics_Motion
– Select All: Select all blocks.
– Clear All: Clear all block selections.
– Reverse All: Clear all selected blocks within the
screen and select all unselected blocks within the
screen.
– OK: Save the changes and exit the menu.
– Cancel: Exit the menu without saving the changes.
● Setup
● No.: Select which cameras to apply Motion Detection
to.
● Zone: Define the motion detection block.
– Sensitivity: Set daytime and nighttime sensitivity
settings between 1 (Low) and 5 (High).
– Min. Blocks: Motion needs to be detected in more
than the specified number of blocks in order to
trigger a Motion Detection event. You may select a
value between 1 and the number of blocks selected
under Zone for daytime and nighttime, each.
Use the remote control’s arrow buttons to move the
block selection window up, down, left, and right. The
selection window consists of 8 blocks per row. Select/
deselect individual blocks using the Camera buttons.
You can use the mouse to drag the zone and then select,
clear, or reverse the selection.
– Ignoring Interval: The system does not produce
event log entries or remote notifications for motion
detected within a certain period of time after the
motion of the camera channels is detected. Set the
value between 1 sec and 5 secs or choose Never.
Ignoring Interval does not affect motion detection
recording.
59
Part 2 - Configuration
– Daytime Setup: Specify when daytime starts
and ends. Adjust the time frame in 15-minute
increments. Times outside the specified range will
be assumed as nighttime by the system.
Video-Analytics_Trip Zone
● Actions: Specify which actions to take when motion
is detected.
– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
– Alarm-Out: Designate event-triggered alarm-out
channels (each for the NVR and camera) and beeps.
– Notify: Configure to be notified of events by Mail,
LAN1 through 5, Push, HTTP, FTP, and/or Alert
Window.
● No.: Select which cameras to apply Trip Zone to.
● Zone: Define the motion detection block.
– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
– Event Monitoring: Selects the cameras to monitor
when an event occurs.
In order to use the Callback feature, the NVR must be
registered on the remote program.
● Condition: When a specific event occurs, you can set
the condition that determines whether to operate
motion according to the status of other events.
– Reference Only: Set the event to be the subject of
a reference.
– Event: Set the reference event.
– Channel: Set the reference channel.
60
Use the remote control’s arrow buttons to move the
block selection window up, down, left, and right. The
selection window consists of 8 blocks per row. Select/
deselect individual blocks using the Camera buttons.
You can use the mouse to drag the zone and then select,
clear, or reverse the selection.
button
From the zone selection screen, press the
on the remote control or right-click on the mouse to
open up the Zone Setup menu.
Part 2 - Configuration
Trip Zone Ignoring Time does not affect Trip Zone
recording.
– Daytime Setup: Specify when daytime starts
and ends. Adjust the time frame in 15-minute
increments. Times outside the specified range will
be assumed as nighttime by the system.
● Actions: Specify which actions to take when Trip Zone
is detected.
– Select: Confirm the block selection in the selection
window.
– Clear: Clear the block selection in the selection
window.
– Reverse: Clear the blocks selected within the
selection window and select all unselected blocks
within the selection window.
– Select All: Select all blocks.
– Clear All: Clear all block selections.
– Reverse All: Clear all selected blocks within the
screen and select all unselected blocks within the
screen.
– Trip Direction: Define in which direction the
motion has to occur in order for it to be considered
an event. Select In for movements from outside the
selection area in or Out for movements from inside
the selection area out.
– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
– Notify: Configure to be notified of events by Mail,
LAN1 through 5, Push, FTP, and/or Alert Window.
– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
– Event Monitoring: Selects the cameras to monitor
when an event occurs.
In order to use the Callback feature, the NVR must be
registered on the remote program.
– OK: Save the changes and exit the menu.
– Cancel: Exit the menu without saving the changes.
● Setup
– Sensitivity: Set daytime and nighttime sensitivity
settings between 1 (Low) and 5 (High).
– Ignoring Interval: The system does not produce
event log entries or remote notifications for
events detected within a certain period of time
after Tripzone events of the camera channels are
detected. Set a value between 1 sec and 5 secs or
choose Never.
61
Part 2 - Configuration
Video-Analytics_Tampering
● Actions: Specify which actions to take when
Tampering is detected.
– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
– Notify: Configure to be notified of events by Mail,
LAN1 through 5, Push, and/or Alert Window.
– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
● No.: Select which cameras to apply Tampering to.
● Sensitivity: Set to between 1 (Low) and 5 (High).
● Activation Time: Specify how long tampering
detection needs to last in order for it to be considered
an event. Tampering detections that do not last for
the specified duration of time will not be considered
as events.
● Ignore Condition
– Use Ignoring Time: Select Time Setup to specify
the tampering detection ignore time of camera
channels. Tampering detection will be disabled
during the specified time frame.
62
– Event Monitoring: Selects the cameras to monitor
when an event occurs.
In order to use the Callback feature, the NVR must be
registered on the remote program.
● Use Ignoring Time: Select Time Setup to specify
the tampering detection ignore time. Tampering
detection will be disabled during the specified time
frame.
Part 2 - Configuration
Video-Analytics_Auto Tracking
When the PTZ camera detects a moving object, the
camera operates the PTZ to track the moving object.
Auto tracking event occur simultaneously when the PTZ
camera tracks an object.
● Actions: Specify which actions to take when Alarm-In
is detected.
– Record: Specify which cameras to begin linked
recording on when an event occurs. If the schedule
is set to Event or Time & Event mode, the selected
cameras will begin linked recording when an event
occurs.
– Notify: Configure to be notified of events by Mail,
LAN1 through 5, Push, FTP, and/or Alert Window.
– PTZ: Moves the PTZ camera to a specific preset
position when an event occurs.
– Event Monitoring: Selects the cameras to monitor
when an event occurs.
● No.: Select which cameras to apply Auto Tracking to.
● Using Zoom: When tracking an object, the PTZ zooms
in the object.
● Object Size: Set the zoom level when using auto
tracking. The larger the object size is set, the larger the
object will be displayed on the screen.
This setting is enabled only when the Zoom
function is on.
● Wait Time After Trace: After the object tracking is
completed, the camera monitors the end poistion for
a set period of time and then moves the PTZ to the
initial position.
• If you do not set this function, the PTZ will not
move to the initial position after auto tracking
ends.
• Only some PTZ cameras support this event.
Please contact the manufacturer for availability
of this event.
• When setting the PTZ with an linked action in the
Action tab, the camera where the event occurs
cannot be set to PTZ linked action camera. For
instance, when setting PTZ on the Auto TrackingActions(no.8) tab, you cannot set PTZ of no.8
camera.
63
Part 2 - Configuration
Network Setup
Refer to the Menu Use on page 29 for basic
information on using the Setup menus.
WAN
Designate the IP address type as IPv4_None, IPv4_
Manual, IPv4_DHCP, IPv6_None or IPv6_Link-local.
IPv4_None
General
Select None and then save to disable IPv4 mode.
● Enable SSL for Transferring Data: Applies SSL
(Secure Sockets Layer) protection on remote viewing
and recording data transmissions.
IPv4_Manual
• If using the SSL feature, it will not be possible to
connect to the NVR from a remote program or a
network keyboard that does not support SSL.
• Changing the SSL setting temporarily severs all
remote connections to the NVR in order to apply the
change.
• This product contains content developed by
OpenSSL Project for use in Open SSL Toolkit (http://
www.openssl.org/).
● Network Bandwidth Limit: Configure the network
bandwidth sent to the remote locale.
– Bitrate: Set the size of the bandwidth.
– Burst: Set the burst-byte or buffer byte size.
– Latency: Set the latency.
– MTU: Set the maximum transmission unit (MTU).
If you configured Network Bandwidth Limit, the live
video may not display smoothly in a remote program.
64
● Set Type to Manual.
Manual lets you configure related settings manually.
Configure IP Address, Gateway, and Subnet Mask
settings manually using virtual keyboard's arrow
buttons.
● DNS Server: Enter the DNS server’s IP address. The
IP address can also be entered using the virtual
keyboard.
● Remote Port: The port used by the remote program
to connect to the NVR. Choose a value between 1024
and 65535. The port number can also be entered
using the virtual keyboard.
Part 2 - Configuration
● Ping Test: Select to test the current WAN settings you
made.
● Trace Route Test: The NVR tries to trace a network
path to its destination.
1
Set the network address of the destination.
1
Enter the IP address of the NVR.
2
Set the maximum number of hops.
2
Adjust the frequency of the ping test.
3
Select Run to do the test. The test result is displayed.
3
Select Run to do the test. The test result is displayed.
4
Select Close to exit.
4
Select Close to exit.
• If using a firewall, select Change Port to change the
port number to one that is permitted by the firewall.
• Changing the port temporarily severs the NVR's
remote connection.
Remote point IP and port settings on the remote
program must also be changed in order for it to
connect to the NVR.
● To use the UPnP (Universal Plug and Play) feature,
select Use UPnP. If using an IP router (or NAT), UPnP
service allows the device to automatically forward the
port to the NVR.
• This port is used to access a port that has a private
IP address.
• In order to use the UPnP service, the IP router (or
NAT) must support UPnP port forwarding and have
the relevant options enabled.
• Port number cannot be changed with Use UPnP
selected.
● Status: Indicates the number of the port forwarded
by the IP router (or NAT) to the NVR via UPnP service.
65
Part 2 - Configuration
IPv4_DHCP
Select DHCP and then Save to retrieve IP address and
other network settings automatically from the DHCP
server. Once the network settings have been retrieved,
the NVR’s current IP address is displayed in the IP
Address field.
• It may not be possible to retrieve the IP address if
there is no DHCP server. If this is the case, contact
your network administrator.
• With DHCP, the NVR's IP address might change with
each startup.
There is a limit to the number of users allowed to
connect remotely at the same time. Contact the
service center for more information.
IPv6_Manual
• Manual lets you configure related settings
manually. Configure IP Address, Prefix Length,
Gateway, and DNS Server settings manually using
the remote control's arrow buttons or the virtual
keyboard.
• When registering NVR with the IDIS mobile
application, you can easily enter the IP address
using the QR code.
IPv6_Link-local
When registering nvr with the Idis mobile application,
you can easily enter the IP address by using the QR
code
IPv6_None
Configure the Link-local address. It is used by nodes
when communicating with neighboring nodes on the
same link.
Select None and then save to disable IPv6 mode.
66
Part 2 - Configuration
VIN
If the camera is networked but not scanned, use this
setup. This setup allows you to change the network
setting of the NVR’s VIDEO IN port which is camera’s
network environment. Check the camera’s network
setting first before you use this setup.
• Check the camera’s network setting first
before you use this setup.
• Make sure that this setting does not
conflict with the WAN setting.
● DHCP Client: Retrieves an IP address and other
network settings automatically from a DHCP server.
– Use NAT(ROUTER/VPN/ETC): Allows access to
other subnets. (It is not recommended to use this
function unless you are a network expert.)
● Link-local address: Indicates the default IP address of
VIDEO IN port.
● Manual: Allows you to enter the IP address and other
network settings manually.
● DHCP Server: It makes the NVR run as a DHCP
server. Check if there is another DHCP server on
the same network. If there is no DHCP server,
this option is enabled. The NVR allocates an IP
address automatically in the range of 10.10.0.128
to 10.10.254.254 by using DHCP to the camera
connected to the NVR’s VIDEO IN port.
When several NVRs exist in the same network,
only one of NVRs has to be run as a DHCP server. If
several DHCP servers are running, the redundant IP
may be allocated to the camera.
– Use NAT(ROUTER/VPN/ETC): Allows access to
other subnets. (It is not recommended to use this
function unless you are a network expert.)
67
Part 2 - Configuration
FEN
If using a dynamic IP address, FEN service makes it easy
to connect to the NVR from a remote program without
having to configure dynamic IP or router settings.
● Use FEN: Check if you wish to use FEN service.
● FEN Name: After entering the NVR name you wish
to register on the FEN server, check and register the
entered name. This is a unique NVR name that will be
registered on the FEN server.
• You will not be able to save FEN settings unless
you click on the Check button next to the NVR
Name field and check the entered name's
availability.
• You will be prompted with an error message
if you do not enter NVR name or enter a name
already registered to the FEN Server.
• If you leave the FEN name blank, it automatically
changes to the default name.
● FEN Server: Enter the FEN server’s IP address or
domain name.
If you have configured the DNS Server setting under
Network - WAN, you can enter the FEN server's
domain name instead of its IP address in the FEN
Server field.
● Port: Specify the FEN server’s port number.
If using an IP router (or NAT), port configuration and
other network functions will depend on the usage
method of the IP router (or NAT).
● Status: Used to check the status of the device being
registered to the FEN server.
Select Save after making changes to register the NVR’s
name to the FEN server.
If FEN has been configured correctly, the FEN server's
help desk information will be displayed in the Help
Desk field the next time you access the FEN Setup
screen.
68
When registering nvr with the Idis mobile application,
you can easily enter the IP address by using the QR
code.
Part 2 - Configuration
Firewall
Setting up a customized firewall rule set, it allows or
denies access such as specific MAC address, IP address
and receiving network port of the NVR.
Notification Setup
Schedule
Select the + icon at the lower left corner of the screen to
add a notification schedule.
Select Use Firewall to activate firewall function. Click
the + icon at the bottom of the list to set up a firewall
rule.
● Day: Add different schedules for different days of the
week.
● Range: Change the event notification time frame.
● Notify: Select which notifications to generate when
an event occurs. Select Mail, LAN 1 through 5, Push,
HTTP, and/or Summary.
● Title: Edit the name of the rule.
● Type: Set the IP address, the MAC address or the
network port.
● Action: Select which actions to apply this firewall rule
to.
– Drop: Discard the packet that matches all the
specified conditions.
• In order to use the Notification (Callback) feature,
the NVR must be registered on the remote program.
• Select the
icon to delete the existing schedule.
● Summary Email Interval: Transmit event summary
emails to a remote destination at specified intervals.
– Reject: Deny the packet that matches all the
specified conditions and send back an ACK packet
telling it that the "packet was dropped" to the
sender.
– Accept: Allow the packet that matches all the
specified conditions.
● Interface: Specify the ethernet interface. It refers to a
WAN (Network Client) or VIN (Video-In).
● Mac Address: If the rule is set to MAC address, enter
the sending MAC address
● IP: If the type of the rule is set to IPv4 or within the
IPv4 scope, enter the sending IP address.
● Port: If the type of the rule is set to port or within the
port scope, enter the receiving network port number
of NVR.
69
Part 2 - Configuration
Callback
Configure Callback settings.
Enter the IP address of the receiving server and set
Retry to between 1 and 10 in case of connection failure.
Select the Setup... button at the lower right corner of the
screen to configure Callback Retry Policy.
● Retry Policy: Configure a policy to retry a callback
event.
– Retry: Number of times to retry a callback event.
– Dwell: Wait time (in seconds) between retry
attempts
70
● Max. Queue Size : Determine the maximum number
that can be processing events. You can limit from 300
to 1000 queues. For more information on Callback
Retry Policy, refer to the graph below.
Part 2 - Configuration
Mail
SMTP Setup
Configure Mail settings.
● +Group: Add a recipient group and select the image
file format attached to an email.
Select SMTP Setup at the bottom right corner of the
screen to configure an SMTP server.
1
Select the SMTP server Type.
2
Enter the SMTP Server’s IP address or domain name
and then configure the Port and Sender settings.
Default SMTP server port number is 25. Select Test to
send out a test mail using the current settings.
Select SS/TLS or STARTTLS, depending a method of
supporting a secure connection.
A virtual keyboard appears allowing you to enter the
Group name. When selecting MP4, the NVR will attach
the event detected image file (MP4 format) to an email.
• If you have configured the DNS Server setting under
Network - WAN, you can enter the STMP server's
domain name instead of its IP address in the SMTP
Server field.
● +Mail: Add a mail recipient
Select the group name and then assign the Group to
Recipient. Enter the the recipient's e-mail address and
mail server provider. Select the icon to select the mail
server provider from a list ot registered SMTP mail server
providers.
The recipient's mail address must be in the correct
email format and contain the @ symbol.
Select the Attach Type to attach event recordings
to outgoing mails to an account that belongs to that
group.
Select the
group.
• Address entered under Sender must be in the
correct email format and include the @ symbol.
If user authentication is required by the SMTP server,
select Use and then enter the User and Password
information.
3
Select OK to apply and exit.
This product contains content developed by OpenSSL
Project for use in Open SSL Toolkit (http://www.
openssl.org/).
icon to remove the account and added
71
Part 2 - Configuration
Attach Type Setup
Push
Configure Push settings.
● Encoding (File name): Set the encoding for the name
of the attached files to BASE64 or PLAIN-TEXT.
● Priority: Set the stream video for email and FTP
attached files to Main Stream or Sub Stream.
● MP4 Clip: When sending an e-mail, event recordings
will be attached and you can set the time to record
MP4 clips.
Event recordings are attached only for the event
that the camera generates.
Select Push to use Push feature.
The Push feature sends out event-related messages to
mobile phone.
Enable to receive the event occured in NVR on the
mobile phone(Android, iOS). The NVR must be
registered and set in mobile phone.
HTTP
Notify or forward the events on remote HTTP servers.
The event and NVR information are sent to HTTP servers
in a JSON format.
Click the + icon at the bottom of the list to enter the
HTTP server information.
● Data Format: Set the data format of transmitted
messages.
● Title: Enter the name of the HTTP site.
72
Part 2 - Configuration
● Address: Enter the address of HTTP notifications.
● Path: Enter the path of HTTP server address.
● User / Password: Enter the user and password to
access the HTTP site.
HTTP Notification Setup
An attribute and parameters must be included when
sending the http requests. Click the Setup... icon at a
bottom right corner of the window. When the following
window appears, click the + button to set the HTTP
attributes such as the type, name and value.
● HTTP Request Parameters: Set a specific response
to an HTTP request.
– Timeout: Set the maximum time allowed for
connection.
– Retry: Set the number of times to reconnect when
a connection fails.
– Delay Time (Retry): Configure the time interval
between each retry attempt (initial delay between
retry attempts)
HTTP Notification Attribute
Display Setup
Refer to the Menu Use on page 29 for basic
information on using the Setup menus.
OSD
Show OSD (On Screen Display) information on the
bottom of the screen.
Status
● Date and Time: Displays the date and time.
● Network: Displays the icon when the unit is
connected to a network via Ethernet.
● Free Space: Displays whether or not the NVR is in
the recycle mode, and displays the available storage
space when not in the recycle mode.
● User Name: Displays the current user logged in.
● Background Panel: Displays background panel at the
bottom of the screen in black.
Camera
● No.: Displays the camera number on the upper left
corner of the camera screen.
● Title: Displays the camera name on the upper left
corner of the camera screen.
● Type: Select the corresponding type such as BOOL,
INT32, FLOAT32 and STRING.
● Record: Displays recording and schedule icons.
● Name: Enter the name of HTTP notification attribute.
● PTZ Zoom: Displays the zoom magnification (e.g. x2,
x3, etc.)
● Value: Enter the value of HTTP notification attribute.
● PTZ: Displays the
icon on PTZ cameras.
● Resolution: Displays the recording resolution.
● Codec: Displays the codec information.
● Zoom: Displays a zoomed in state.
73
Part 2 - Configuration
● Freeze & Sequence: Displays freeze and sequence
icons.
● Screen Group: Displays the current screen's group.
Main Monitor
Status Setup
Refer to the Menu Use on page 29 for basic
information on using the Setup menus.
Camera
Configure monitor-related settings.
This screen displays an overview of camera events.
When an event occurs, the corresponding channel
flashes for 5 seconds.
● Mode: Select Full Sequence or Cameo Sequence.
● Interval: Select between 3 secs and 2 mins. For more
information on Sequence, refer to the 7 Sequence on
page 23.
● Manual Configuration: Set the resolution manually
regardless of the resolution supported by the monitor.
● Resolution: Select from 1920 x 1200, 1920 x 1080,
1680 x 1050 and 1600 x 1200.
● Event Monitoring On: With Event Monitoring
enabled, the camera screen linking event monitoring
is shown. For more information on Event Monitoring,
refer to the Event Monitoring on page 26.
● Event Alert: With Event Alert selected, the red line
appears on the top of the camera screen linking event
monitoring when an event occurs.
• Supported resolutions may be restricted
depending on the monitor.
• We recommend using 1920 x 1080 resolution.
• If you use a VGA monitor as the main display, we
recommend that you use a resolution of 1920 x
1080 or below.
• HDMI deep color feature is not supported.
● Use BRP(Boost Remote Performance) mode : With
BRP mode on, the camera full screen does not display
in live mode and the network bandwidth can limit to
50Mbps.
● Priority : Select the camera's live stream priority,
either resolution or frame rate.
74
Event Types
Motion
Trip Zone
Tampering
Video Loss
PIR
Auto Tracking
Part 2 - Configuration
Device
System
This screen displays an overview of device events.
When an event occurs, the corresponding channel
flashes for 5 seconds.
This screen displays an overview of system events.
When an event occurs, the corresponding channel
flashes for 5 seconds.
Event Types
● Panic Record: Displays event status based on current
Panic Record status.
**Recording Fail of
Main Stream
**Recording Fail of
Sub Stream
** The two events are supported by some products
only.
● Check Recording: Displays event status based on
System Monitoring settings. For more information,
refer to the Self-Diagnosis on page 38.
● Disk Almost Full/Disk Full: If the storage device is
not in Recycle status, event status is displayed when
the amount of disk space specified under System
Monitoring is reached and when the disk becomes
100% full. For more information, refer to the SelfDiagnosis on page 38.
● Disk Config Change: It will be highlighted when
the NVR reboots after the hard disk drive has been
replaced.
● No Storage Found: It will be highlighted when no
recordable storage device has been found.
75
Part 2 - Configuration
Storage
Not
Formatted
Indicates each disk's status.
A disk that has never
been used before.
● Disk performing
normally.
Good
Disk Bad
Error
● If the HDD is partially
damaged, indicates
the bad sector
percentage.
● If the HDD's bad
sector ratio is higher
than as designated
by the user.
● Generates a system
event.
Configure Disk Bad and Disk Temperature settings under
Setup > System > Monitoring.
N/A
Unable to detect the
disk's temperature.
Good
Operating within
normal temperature
range.
Temperature
Bad
● Disk temperature
higher than as
designated by the
user.
● Generates a system
event.
N/A
A disk that does not
support S.M.A.R.T.
Good
A disk with normal
S.M.A.R.T. status.
Bad
A disk with abnormal
S.M.A.R.T. status.
Possibility of damage
within 24 hours.
S.M.A.R.T.
• Check each disk's data storage time information
under Recording Data.
• Clicking the temperature, S.M.A.R.T can check the
each HDD information.
76
Part 2 - Configuration
Network
This page provides a complete overview of the network
status in real-time.
Information shown include camera connection status,
LAN port link status, power consumption, number of
connected clients, and network connection info.
Camera
Connection
indicates the camera is
indicates the
connected.
camera is not connected. Clicking
the image displays the camera's
channel number. Clicking the
image displays status information
of the device connected to the
NVR.
indicates a network switch
is connected to the LAN port and
shows how many cameras are
connected. Clicking the image
Network Switch
displays the camera’s channel
number. Clicking the image displays
status information of the device
connected to the NVR.
Video Encoder
indicates a video encoder
is connected to the LAN port and
shows how many cameras are
connected. Clicking the image
displays the camera’s channel
number. Clicking the image displays
status information of the device
connected to the NVR.
LAN Port Link
indicates a camera or a
network switch is connected.
indicates neither is connected.
Power
Consumption
If receiving power from the NVR,
the actual amount of power
consumed by each camera is
indicated under each camera icon.
Total power consumption is shown
at the top of the screen.
[[Total PoE Power Consumption:
13.9W (Max 4ch : 30.0W, 8ch :
50.0W)]
Ports 1 through 4 in PoE-enabled
products support PoE.
(NETWORK CLIENT) ports
do not support PoE.
77
Part 2 - Configuration
Number of
Connected
Clients
Indicates whether there are clients
connected to the NVR via an
external network and how many
clients are connected.
indicates at least one client
indicates no
is connected.
client is connected.
Indicates network connection
statuses (connected, connecting,
disconnected, and connection
error) using following lines:
Network
Connection
Info
(WARNING: When PoE switch
is connected and network
bandwidth is less than 100Mbps)
(ERROR: When PoE switch
is connected and network
bandwidth is less than 10Mbps)
78
Part 3 - Search
Time-Lapse Search
Search by changing Time-Lapse Search and Event
Log Search.
While in Live mode, select the Search Mode
icon
and select Time-Lapse Search, or Event Log Search.
Search Menu
1
2
3
1
4 5
6 7 8
1 Layout
Used to change the screen layout to single screen,
1x2, corridor format or 2x2.
2
2 Previous/Next Group
Loads the previous/next screen group.
3 Display
● Full Screen On: Display the screen with a 16:
9 aspect ratio. When you place the mouse at
the bottom of the screen, the interface screen
related to playback will appear. Refer to detailed
explanations on the next page.
● Full Screen OFF: Display Time-Lapse Search
screen.
● Camera OSD On/Off: Enables/disables the camera
OSD feature.
● Status OSD On/Off: Enables/disables the status
OSD feature.
● Aspect Ratio On/Off: Setting On displays video on
the camera screen in its original ratio.
4 Database
● Record: Search recording data contained in the
main recording device.
● Other: Search data recorded while disks used in
other systems were connected.
5 Panic Record
Use the Panic Record feature.
6 Camera
Select a camera channel and display it as a single
screen.
7 Live Mode
Activates Live mode.
8 Search Mode
3
4
5
6
7
1 Bookmark
icon to add a bookmark to the current
Select the
playback position.
Select a bookmark from the Bookmark setup window on
the right side of the Time-Lapse Search mode screen to
move to the registered playback position.
icon to delete the
Select Bookmark list and then the
corresponding bookmark.
The maximum number of bookmarks that can be
saved is 12.
2 Playback Controls
Play and scan through video recordings.
● Jog Shuttle
Adjust the playback method and speed.
Jog shuttle’s vertical indicator indicates the current
playback direction and speed. Vertical indicator
placement to the right of the center means the
video is being played back in the forward direction.
Placement to the left means the opposite. Farther
away the vertical indicator from the center, faster the
playback speed. Click and drag the vertical indicator
79
Part 3 - Search
to adjust the playback speed. Releasing the mouse
button returns the vertical indicator to the center and
stops video playback.
● Slow Play
Search the playback screen at low speeds. Select the
desired playback speed (x1/2, x1/3, x1/4, x1/6, x1/8)
and then select Play.
3 Calendar Search
Use the calendar to search for video recordings by
specific dates.
Dates containing video recordings are highlighted in
light blue. Selecting a date containing video recording
data loads the earliest recording from that date (paused
state). Selected date is highlighted in orange.
4 Move
Search video recordings based on date and time. Specify
the date and time and then select Go to jump to the
corresponding video recording.
• Farther back the data is on the record table, the
more recent it is.
• If the system's clock is changed to a previous date
and time, it is possible for multiple recordings
with the identical time stamp to exist. Overlapped
segments are highlighted in yellow.
Select
(zoom-in) to compose recording data
(zoom-out)
in 1-minute segments and select
to compose recording data in 3-minute segments.
Selecting zoom-out displays more time in one screen
than zoom-in screen.
If recording from points in time prior or after the time
frame displayed on the screen is available, scrolls appear
on both ends of the date and time information line. With
a mouse, click and drag the vertical scroll bar to check
recording data.
Display the latest update recording information when
(Refresh).
selecting
Recording Data Bar Colors
Select a
(bookmark) button on the right side to move
to the saved bookmark position.
Blue
Time Lapse Recording
Purple
Event Recording
Yellow
Pre-Event Recording
Red
Panic Recording
Green
- Faulty recording due to a
temporary disruption in device
connection
5 Clip-Copy
● A-B Clip Copy: Designate a start point and an end
point and copy the data in between.
● Clip Copy: Opens up the Clip Copy Setup window for
designating points A and B.
6 Zoom
Zoom in.
7 Record Table
Display the current channel’s recording information.
Recording date and time are shown on the top of the
search window. The gray indicator line on Record Table
indicates the current playback position. Alternatively,
use the mouse to jump to the desired playback position.
80
Context Menu
Right-click on the Camera screen to access the context
menu.
● Zoom: Zoom in.
● Edit Group: Rearrange the split screen layout.
Part 3 - Search
Clip Copy
Clip Copy
Select Clip-Copy – Clip Copy from the Search menu
while in Live or Playback mode to open up the Clip
Copy setup window. Specify the From and To settings.
A-B Clip Copy
Designate a start point and an end point and copy the
data in between. Select Clip-Copy – A-B Clip Copy from
icon will appear
the Search menu to set point A. The
on the status indicator area on the upper right corner
of the screen. Select Clip-Copy – A-B Clip Copy once
again to set point B. The Clip Copy Setup window will
appear. Select A and B points are automatically applied
as From and To values.
● Use Site Info: Adds Site info to the Clip Copy file’s
name.
Special characters contained in the location info
(such as \, /, :, ;, *, ?, !, “, <, >, and |) will be replaced
with _ when the information is added to the file
name.
● Export Clipplayer: Enabling this option will save the
copied clip(.cbf ) as a clipplayer to be played.
Selecting Start displays a calculation on the size of the
data to be copied. Check the calculation and then select
Continue to proceed. While Clip Copy is in progress, you
can select Cancel to cancel the process or select Close
to allow the window to run in the background. Selecting
Close does not cancel Clip Copy. Once the process is
complete, you will be prompted with a confirmation
window.
Click Export ClipPlayer button to save the clipplayer.exe
file playing CBF files to USB.
• The NVR displays the volume as 30GB regardless of
the actual disk volume and the maximum size limit
on Clip Copy files is 30GB. Clip Copying a segment
that is more than 2GB in size produces multiple files
that are up to 2GB in size, each.
• Clip Copy files can be played back on Windows
systems. For more information, refer to the IDIS
Center operation manual.
• For USB flash memory devices, the NVR supports the
FAT32 file format only.
● Channels: Specify which channel to save the
recording to.
● Password: Enable password protection for the saved
video clip and assign a password.
● Dest.: Select which storage media to use.
● File name: Designate a name for the file. The name
may be up to 63 characters in length.
Special characters such as \, /, :, ;, *, ?, !, “, <, >, and |
are not permitted.
● Include ClipPlayer: Enabling this option will save the
video clip as an .exe file with clipplayer.
Do not disconnect the USB cable or power off the USB
device while USB Clip Copy is in progress. Doing so
can cause the NVR to malfunction or critically damage
the external USB device's file system. You may be
prompted with an error message when trying to back
up on the device. If so, you will need to restart the NVR.
If the USB hard disk's file system has been damaged,
restarting the NVR will not solve the problem and
the aforementioned error message will continue to
be displayed each time you attempt a backup. If this
is the case, you will need to format the HDD or use a
recovery program to repair the damage to the drive's
file system.
● Sub Stream First: If the video clip has dual recording
information, the sub stream is saved first.
81
Part 3 - Search
Event Log Search
Select Search Mode > Event Log Search to bring up
the Event Log Search window.
● Use event filters to include/exclude specific system
events such as Panic Record, Check Recording,
Disk Almost Full, Disk Bad, Disk Temperature, Disk
S.M.A.R.T., and Disk Config Change from the search.
Device Filter
● Motion: Select which channels to search motion
detection events in.
● Video Loss: Select which channels to search video
loss events in.
● Trip Zone: Select which channels to search trip zone
events in.
Select an eent to display the recording made on the
selected time and date (paused state). Select the Play
button in the middle of the screen to start playing back
the recording. Use the drop-down menu above to load
recordings from other cameras.
● Selecting the specific event displays the screen to be
button on the camera
stationary. By clicking the
right, you can copy the event.
● You can uncheck the First and Last options at the
top of the Event Log Search window and specify the
search time frame manually.
Select First for From and Last for To to select the entire
recording from start to end.
● If designating From or To settings manually, you will
be able to enable/disable the Check Time Overlap
option.
● Exceed the People Limit: Select which channels to
search Exceed the People Limit events in.
● Exceed the Time Limit: Select which channels to
search Exceed the Time Limit events in.
If the system's clock has been changed and the
designated From or To point exists at more than one
location, you will have to choose one. Only the events
that took place between the selected From and To
points will be searched. If Check Time Overlap has
not been selected, events from the entire From and To
range will be searched.
82
● Tampering: Select which channels to search
tampering events in.
● Record Channel: Select which record channels to
search events in.
● Recording Fail: Select which channels to search
recording fail events in.
● PIR: Select which channels to search PIR events in.
● Auto Tracking: Select which channels to search Auto
Tracking events in.
Selected record channels are searched for events with
at least one linked recording. If no camera is selected,
only the events with no linked recording camera are
searched.
Part 3 - Search
Overlapped Recording Search
If the system’s clock is changed to a point in the past,
overlapping recordings may be produced. Overlapped
recordings have to be searched in segments.
For example, making a recording from 1 o’clock to 5
o’clock, changing the system’s clock at 5 o’clock to 3
o’clock, and then continuing to record until 6 o’clock
produces two recordings that overlap between 3 o’clock
and 5 o’clock. This results in two segments for the period
between 3 and 5.
1:00
Segment 1
Segment 2
2:00
3:00
4:00
5:00
3:00
4:00
5:00
6:00
When searching overlapped video recordings, you
can choose a specific point in time or a time frame. If
you use the Go to the Date/Time option and select a
point within the overlapped time period (4 o’clock, for
example), you must specify 4 o’clock in which of the
two existing segments.
If you use the Event Log Search or Motion Detection
option and select a time frame within the overlapped
time period (4 o’clock to 5 o’clock, for example), you
must choose between the two redundant sets of From
and To values. Selectable search ranges are as follows:
● 4 o’clock in segment 1 to 5 o’clock in segment 1
● 4 o’clock in segment 1 to 5 o’clock in segment 2
● 4 o’clock in segment 2 to 5 o’clock in segment 2
83
Part 3 - Search
Memo
84
V8.2
IDIS Co., Ltd.
For more information, please visit at
www.idisglobal.com
">