BR2-900
2 Relay Logic Module with Built-In
900 MHz Wireless Technology
(US version)
DESCRIPTION
8
9
10
11
12
1 C
2
1. Power input
2. Relay outputs
3. Day/Night input
4. AUX input
HAND-HELD TRANSMITTERS
3
4
5
6
7
5. Learn buttons
6. DIP-switches
7. Potentiometers
8. Radio frequency LED (red)
9. Relay 2 LED (white)
10. Relay 1 LED (blue)
11. Tri-color signal strength LED
12. Antenna
10TD900HH1: 1-button transmitter 10TD900HH2: 2-button transmitter 10TD900HH3: 3-button transmitter 10TD900HH4: 4-button transmitter
10TD900PB: Push Plate transmitter
10TD900TR: Touchless Retrofit transmitter
10TD900HH1U: 1-button
Universal transmitter
75.5886.03 BR2-900 20230411 Page 1 of 8
PRECAUTIONS
Shut off all power going to header before attempting any wiring procedures.
Maintain a clean and safe environment when working in public areas.
Constantly be aware of pedestrian traffic around the door area.
Always stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door.
ESD (electrostatic discharge): Circuit boards are vulnerable to damage by electrostatic discharge.
Before handling any board, ensure you dissipate your body’s ESD charge.
Always check placement of all wiring before powering up to ensure that moving door parts will not catch any wires and cause damage to equipment.
Ensure compliance with all applicable safety standards (e.g. ANSI A156.10) upon completion of installation.
DO NOT attempt any internal repair of the components. All repairs and/or component replacements must be performed by BEA, Inc. Unauthorized disassembly or repair may:
1. jeopardize personal safety and may expose one to the risk of electrical shock.
2. adversely affect the safe and reliable performance of the product resulting in a voided warranty.
INSTALLATION
Wiring
POWER
Br2-900
RoHS Compliant
2 Relay Logic Module
900 MHz Wireless
RELAYS INPUTS
D/N AUX
LEARN HOLD TIME
12 to 24
VAC/VDC
+/- 10%
Locking device
Activation circuit of door control
‘DRY’ contact activation device
Keyswitch or other ‘DRY’ contact device
Relays 1 and 2 are DPDT: relays 1A and 1B fire simultaneously and relays 2A and 2B fire simultaneously.
Relays 1B and 2B are commonly used in applications with two (2) locking devices and/or with two (2) independent door controls.
INPUT D/N (DAY/NIGHT mode) when open, allows transmitters learned in both SECURE mode and UNSECURE mode to function when closed, only allows transmitters learned in UNSECURE mode to function
INPUT AUX functions regardless of learn, DIP switch, or potentiometer settings.
Page 2 of 8 75.5886.03 BR2-900 20230411
USER INTERFACE
DIP-Switches
DIP switches can be set to achieve desired functionality based upon specific application requirements.
DIP
1
STATUS
STD
UNI 1
FUNCTION standard mode universal mode 2
DESCRIPTION allows only learned/programmed transmitters to function allows learned/programmed and "universal transmitters" to function
2
STD
EH standard mode extended hold pressing/holding or pressing/releasing transmitter activates and holds relay according to HOLD TIME POTs (single shot) pressing/holding transmitter holds relay as long as transmitter is pressed/ held – once released, relay acts according to HOLD TIME POTs
NOTES:
1. Day/Night mode does not function when DIP-switch 1 is set to UNI.
2. See Universal Mode in SET-UP section (page 5).
Learn Buttons
900 MHz wireless transmitters can be programmed (or "learned") as either UNSECURE or SECURE transmitters.
Any combination of up to 75 transmitters may be programmed.
BUTTON
UNSECURE
SECURE
FUNCTION DESCRIPTION unsecure transmitters learned transmitter functions when INPUT D/N is open or closed secure transmitters learned transmitter only functions when INPUT D/N is open
Potentiometers
Potentiometers control output relay functionality.
POT
HOLD 1
HOLD 2
DELAY
FUNCTION relay 1 hold time relay 2 hold time delay between relay 1 and relay 2
DESCRIPTION
0.5 – 10 seconds
0.5 – 10 seconds
0 – 30 seconds
Signal Strength Indicator
Pressing and holding transmitter button for three (3) seconds activates signal strength LED on Br2-900.
LED COLOR
GREEN
YELLOW
RED
DESCRIPTION strong wireless signal moderate wireless signal weak wireless signal
75.5886.03 BR2-900 20230411 Page 3 of 8
SET-UP
Hand-Held Configuration
1 2 3
Set DIP-switches as desired.
For DIP-switch settings, please refer to table on page 3.
4
R1 see hub image on page 1
R2 DELAY
4
D
Press and release desired Learn button (red LED on Br2-900 will illuminate).
Press transmitter twice (white and blue LEDs on receiver will illuminate).
3 2 1
D
Adjust POTs as desired.
See page 3 for descriptions.
C
Push Plate Configuration
1
B
2
[
1.36"
34.43
mm]
[
4.5"
114.30
mm]
3
C
B
A
Connect transmitter 1 to push into box.
3 2
BEA, INC.
TITLE:
100 ENTERPRISE DRIVE
PITTSBURGH, PA 15275
(800) 523-2462
4.5" Square Text Only Pushplate
A
PART NUMBER: 10PBS45
DRAWING NUMBER:
DRAWN BY: kjgierl
RELEASED:
Follow steps 1 – 4 in
CHECKED BY:
Hand-Held
Configuration above.
NOTES:
1. 10TD900PB required for push plates.
Universal Mode
Universal transmitters (10TD900HH1U) do not need programmed (or "learned") to the Br2-900. Their unique serial number is automatically recognized by the Br2-900.
During the Hand-Held Configuration or the Push Plate Configuration steps (above), standard transmitters must be programmed/learned as either "Secure" or "Unsecure" transmitters. When set to Universal, learned, standard transmitters will function as programmed/learned.
Page 4 of 8 75.5886.03 BR2-900 20230411
SET-UP (CONT.)
Vestibule Configuration
Vestibule applications may be installed and programmed so that either door 1 and door 2 open simultaneously or door 1 opens first and door 2 opens after a delay (set by HOLD TIME potentiometers).
For 2-way traffic, two (2) Br2-900 modules are required.
1-Way Traffic (simultaneous)
Door 1 and Door 2 will open simultaneously.
POWER
Br2-900
RELAYS
2 Relay Logic Module
900 MHz Wireless
INPUTS
D/N AUX
LEARN HOLD TIME
1-Way Traffic (lock + simultaneous)
Lock(s) will unlock and then Door 1 and
Door 2 will open simultaneously.
12 to 24
VAC/VDC
+/- 10%
Door 1 Door 2
POWER
Br2-900
RoHS Compliant
2 Relay Logic Module
900 MHz Wireless
RELAYS INPUTS
D/N AUX
LEARN HOLD TIME
1-Way Traffic (sequence)
Door 1 will open and then Door 2 will open after a delay set by DELAY POT.
12 to 24
VAC/VDC
+/- 10%
Lock Door 1 Door 2
POWER
Br2-900
2 Relay Logic Module
900 MHz Wireless
RELAYS INPUTS
D/N AUX
LEARN HOLD TIME
2-Way Traffic
POWER
Br2-900
2 Relay Logic Module
900 MHz Wireless
RELAYS INPUTS
D/N AUX
LEARN HOLD TIME
12 to 24
VAC/VDC
+/- 10%
MAG
1
MAG
2
Door 1 Door 2
POWER
Br2-900
2 Relay Logic Module
900 MHz Wireless
RELAYS INPUTS
D/N AUX
LEARN HOLD TIME
12 to 24
VAC/VDC
+/- 10%
MAG
1
MAG
2
Door 1 Door 2
Door 1 will open and then Door 2 will open after a delay set by DELAY POT.
75.5886.03 BR2-900 20230411
Door 1 Door 2
12 to 24
VAC/VDC
+/- 10%
Door 2 will open and then Door 1 will open after a delay set by DELAY POT.
Page 5 of 8
REMOVING TRANSMITTERS
Single Transmitter
1 2 x2
Press transmitter TWICE within
10 seconds.
Press BOTH learn buttons until red LED flashes once (~2 s).
All Transmitters
1
Press BOTH Learn buttons until blue LED illuminates (~10 s).
BATTERY REPLACEMENT
Hand-held (TD900HHx)
1
Remove back screws and disassemble.
Push Plate (TD900PB)
1
2
3 V
Replace 3 volt (CR2032) battery observing polarity and reassemble.
Replace 2 AAA batteries observing polarity.
Low Battery Indicator: After transmitter button is pressed, low battery is indicated by three (3) transmitter red LED blinks.
Page 6 of 8 75.5886.03 BR2-900 20230411
TROUBLESHOOTING
Br2-900 will not react to any inputs
Br2-900 has no output
Red LED on receiver flickering; unable to program
Weak signal
Incorrect power
Not programmed
Incorrect wiring
Defective Br2-900
Incorrect output devices
Incorrect wiring
Incorrect settings
Defective Br2-900
Push Plate is stuck
Faulty transmitter
Antenna positioned poorly
Verify power supply of 12 – 24 VAC/VDC
±10% is wired to correct terminals.
Ensure a Br2-900 is programmed with wireless transmitter.
Verify wiring.
Replace Br2-900.
Ensure proper devices are connected to outputs.
Verify wiring.
Verify programming and potentiometer settings.
Replace Br2-900.
Disconnect push plates to determine which one is stuck (LED should go out).
If LED does not go out, remove transmitter batteries to determine which is faulty, replace transmitter.
Position antenna outside of door header.
TECHNICAL SPECIFICATIONS
Supply voltage:
Current consumption:
Frequency:
Emitted radio power:
Power consumption:
Transmitter capacity (per receiver):
Programmable (standard):
Universal:
Temperature rating:
Input
Day / Night (24hr)
AUX
Contact rating:
Relay 1 DPDT / Relay 2 DPDT:
LEDs:
12 – 24 VAC / VDC ±10%
45 mA DC
75 mA AC
908 – 918 MHz (frequency hopping)
-25 dBm (TX)
0.5 – 1.5 W
75 unlimited
-22 – 158 ° F (-30
DRY contact
DRY contact
– 70 ° C)
Certification:
Dimensions:
Housing:
2 A @ 30 VDC or 2 A @ 24 VAC blue (relay 1 activation) white (relay 2 activation) red (radio frequency / learn) tri-color (signal strength)
FCC, IC
5.2" (W) x 1" (H) x 2.2" (D)
(133 mm x 25 mm x 55 mm)
ABS (white translucent)
Specifications are subject to change without prior notice.
All values measured in specific conditions.
75.5886.03 BR2-900 20230411 Page 7 of 8
FCC / IC
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”
Changes or modifications not expressly approved by BEA Incorporated could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
FCC ID: 2ABWS-10BR2900
FCC ID: 2ABWS-10TD900PB
FCC ID: 2ABWS-10TD900HH4
FCC ID: 2ABWS-10TD900HH4
FCC ID: 2ABWS-10TD900HH4
FCC ID: 2ABWS-10TD900HH4
FCC ID: 2ABWS-10TD900HH1U
IC: 4680A-10BR2900
IC: 4680A-10TD900PB
IC: 4680A-10TD900HH4
IC: 4680A-10TD900HH4
IC: 4680A-10TD900HH4
IC: 4680A-10TD900HH4
IC: 4680A-10TD900HH1U
MODEL: 10BR2900
MODEL: 10TD900PB
MODEL: 10TD900HH1
MODEL: 10TD900HH2
MODEL: 10TD900HH3
MODEL: 10TD900HH4
MODEL: 10TD900HH1U
BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device; therefore, BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose.
BEA, Inc. strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/ gates, and factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor/device system performance is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label (e.g.
ANSI/DASMA 102, ANSI/DASMA 107, UL294, UL325, and International Building Code).
Verify that all appropriate industry signage, warning labels, and placards are in place.
Page 8 of 8
Tech Support & Customer Service: 1-800-523-2462
General Tech Questions: [email protected] | Tech Docs: www.BEAsensors.com
75.5886.03 BR2-900 20230411
