User Manual Of LSLA1000 Series

User Manual Of LSLA1000 Series
User Manual
PL10/ML10
Version: 1.0
1
Note
1. New lock is configured to grant ANY fingerprint access to unlock.
2. The lock is equipped with mechanical keys for manual unlocking. Remove mechanical keys from
the package and keep them in a safe place.
3. To power on the lock, four alkaline AA batteries (not included) are required. Non-alkaline and
rechargeable batteries ARE NOT RECOMMENDED.
4. Please avoid strong light direct to the fingerprint holder, otherwise the infrared sensor might be
disturbed.
5. The operation of setting lock has a stand-by time limit of 10 seconds; Without any activity, lock will
shut off after 10 seconds.
6. Keep your fingers clean when using this lock.
1
Appearance
1
2
3
4
5
2
1
Infrared sensor hole
2
LED
3
Fingerprint Sensor
4
Handle
5
Mechanical key hole
6
Battery box cover
7
Battery Area
8
Button
/ Temporary User
9
Button
/ Admin user
10
Back LED
11
Button
/ Delete user
12
Button
/ Add user
13
Reset Button
14
Button
15
9V Emergency battery interface
/ Normal User
6
7
8
9
10
11
12
13
14
15
Profile
User Introduction
User Type
Admin user
Capacity
10
Privilege
Add/delete fingerprint; Enable Normal
Open; Unlock the door
Normal user
60
Unlock the door; Enable Normal Open
Temporary user
20
Unlock the door; Enable Normal Open
Button Definition
Buttons
Function
Other functions
Add Users
Delete Users
Admin User Group
Normal User Group
Temporary User Group
3
Enable Normal Open
Lock Status Indication
Lock Status
Indication
Operation success
1 Beep and LED blinks green
Operation failure:
2 Beep and LED blinks red
Low battery:
7 Beep and LED blinks red 7 times
Unlocking:
1 Beep and electric engine makes a rolling sound for the first
time, which indicates that the door is open.
Locking:
Electric engine makes a rolling sound for the second time,
which indicates that the door is closed.
4
Initialize Lock
Method 1
Operating Steps
Method 2
Indication of the lock
Press the "Reset" button with
a pin.
Touch the infrared sensor hole
to power on the lock
Fingerprint sensor is
power on LED blinks
green
Loosen the pin.
Press the button of "+", "1",
"2", "3" , "-".in order
One beep for each
pressing, back LED
blinks green
Initialization succeed
A long beep, LED blinks
green for 1 second
Operating Steps
Delete all Temporary
Users.
Please see “Delete
Temporary Users”.
Delete all Normal Users
Please see “Delete
Normal Users”.
Delete all Admin Users..
Please see “Delete
Admin Users”.
Reset successfully
Note: The lock will be restored to factory defaults after initialization, and the door can be opened with
any fingerprint.
5
How to use mechanical key?
Hexagon Screw
How to use 9V emergency battery?
6
Register First Admin
Operation Guide
Operating Steps
Indication of the lock
Touch the infrared sensor hole
to power on lock
Fingerprint sensor is power
on, LED blinks green
Press button "+"
One beep
Place one finger 3 times on
the fingerprint sensor
Registration succeed
One Beep for the first two
fingerprints; A long beep
and LED blinks green 1
second for the third
fingerprint.
Note: 1.The first user will be the first Admin automatically at default.
2. Admin group supports 10 users; you can still register 9 new Admins in next step.
7
Register Other Admin
Operation
Guide
Operating Steps
Indication of the lock
Touch the infrared sensor hole
to power on lock
Press button "+"
Fingerprint sensor is power
on, LED blinks green
One beep
Place any admin finger 1 time to
verify Admin
One beep
Press button "1" to select Admin
group
One beep
Place one finger 3 times on the
fingerprint sensor
One Beep for the first two
fingerprints; A long beep and
LED blinks green 1 second
for the third fingerprint.
Registration Succeed
Place one new finger 3 times on
fingerprint sensor to continue
register NEW admin
Note: Admin group supports 10 users; you can still register 9 new Admin in this step.
8
Register Normal User
Operating Steps
Indication of the lock
Touch the infrared sensor hole to power
on the lock
Fingerprint sensor is power
on, LED blinks green
Press button "+"
One beep
Place any admin finger 1 time to verify
Admin
One beep
Press button "2" to select normal user
group
One beep
Place one finger 3 times on the
fingerprint sensor
Registration Succeed
One Beep for the first two
fingerprints; A long beep and
LED blinks green 1 second
for the third fingerprint.
Place one new finger 3 times on
fingerprint sensor to continue register
NEW normal user
Note: Normal User group supports 60 users.
9
Register Temporary User
Operating Steps
Indication of the lock
Touch the infrared sensor hole to
power on the lock
Fingerprint sensor is power
on, LED blinks green
Press button "+"
One beep
Place any admin finger 1 time to
verify Admin
One beep
Press button "3" to select Temporary
user group
One beep
Place one finger 3 times on the
fingerprint sensor
One Beep for the first two
fingerprints; A long beep and
LED blinks green 1 second
for the third fingerprint.
Registration Succeed
Place one new finger 3 times on
fingerprint sensor to continue register
NEW temporary user
Note: Temporary User group supports 20 users.
10
Delete Temporary User Group
Operating Steps
Indication of the lock
Touch the infrared sensor hole
to power on the lock
Fingerprint sensor is power
on, LED blinks green
Press button "-"
One beep
Place any admin finger 1 time
to verify Admin
One beep
Long-press button "3" to delete
Temporary user group
A long beep, LED blinks
green for 1 second
Delete Succeed
Note: All delete operation is only valid for group.
11
Delete Normal User Group
Operating Steps
Indication of the lock
Touch the infrared sensor hole
to power on the lock
Fingerprint sensor is power
on, LED blinks green
Press button "-"
One beep
Place any admin finger 1 time
to verify Admin
One beep
Long-press button "2" to delete
Normal user group
A long beep, LED blinks
green for 1 second
Delete Succeed
Note: All delete operation is only valid for group.
12
Delete Admin Group
Operating Steps
Touch the infrared sensor hole
to power on the lock
Indication of the lock
Fingerprint sensor is power
on, LED blinks green
Press button "-"
One beep
Place any admin finger 1 time
to verify Admin
One beep
Long-press button "1" to delete
Admin group
A long beep, LED blinks
green for 1 second
Delete Succeed
Note: All delete operation is only valid for group.
13
Enable And Disable Normal Open
Enable Normal Open:
Operating Steps
Indication of the lock
Place any registered finger
once to do verification
Fingerprint sensor is power
on, LED blinks green
Long-press "1" button
3 seconds
A long beep, LED blinks
green for 1 second
Disable Normal Open:
Place any registered finger 1 time to disable.
14
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement