E N G L IS H 2in/2out telephone dialer with vocal messages

E N G L IS H 2in/2out telephone dialer with vocal messages
ENGLISH
2in/2out telephone dialer with vocal messages
USER MANUAL
EMC 89/336 73/23 CEE
2in/2out telephone dialer with vocal messages - User Manual
1
Introduction
1.1 Operating features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Technical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2
Installation
2.1 Clamps..................... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Connection example. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3
Programming
3.1 Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1.1
Insertion and elimination of telephone numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1.2
Visualization of telephone numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.2 Channel messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.2.1
Recording / reproduction of channel messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
3.3 State messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.3.1
Recording / reproduction of state messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3.4 Operation inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.5 Operation outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
3.6 Temporizations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.7 Operation parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.8 Modification access code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4
Operating
4.1 Operation general description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.2 Local and remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Appendix A: Values of default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
2
Introduction
1
Introduction
1.1
Operating features
!
!
!
!
!
!
!
!
!
!
!
2 inputs of activation alarm, everyone with a vocal message of alarm of 16 seconds
2 outputs with relè controlling by telephone by DTMF, or by keypad.
Monitoring of the condition of inputs and outputs from remote.
Vocal directory fo 16 numbers.
Listening ambient from remote.
Delays on the programming inputs singularly.
Inputs programming in way impulse or state, conditioned to the logical input “INT”.
Outputs programming in way impulse or state, conditioned to inputs.
Possibility to link together every telephone number to one channel or to both.
Number of repetition message and cycles of programming call.
Tamper antiopening (TD92 and TM92P).
3
2in/2out telephone dialer with vocal messages - User Manual
1.2
!
!
!
!
!
!
!
4
Technical specifications
Operating voltage: 13Vcc ±5%
Absorption: 25mA in St/by
Inputs: 2 + 1 “INT” of condition
Outputs relè to exchange: 2
Vocal messages: 2 (of 16 sec.), one for each channel; 10 (of 2 sec.), for the condition of every
inputs and outputs, in whichever conditions.
Voice directory: 16 numbers
Dimensions: 9 modules DIN (ALADIN2C)
178x115x38mm (TD92)
285x95x17mm (TM92P)
Installation
2
Installation
2.1
Clamps
1
1-2
3-4
5-6-7
8 - 9 - 10
11 - 12 - 13
14
15 - 16
17 - 18
2
3
4
(TD92 and
TM92P)
5
6 7
8 9 10
11 12 13
14 15 16 17 18
Power supply 12Vcc
Tamper antiopening (solo nel TD92 e TM92P)
Inputs commandos +12Vcc:
!
INT: activation to call
!
K1: activation channel 1
!
K2: activation channel 2
Output relè 1
Output relè 2
Ground connection
Input telephone line
Output telephone line
5
2in/2out telephone dialer with vocal messages - User Manual
2.2
Connection example
IN2
IN1
In order to use
outputs ‘+ Sir’ e ‘+ Int.’
The negative of the two
devices must
be in common
INT
Burglar
central unit
Telephone
Line
If only present
positive +Int.
inputs 1 and 2
will be operating
(see
Programming).
Electronic
Key
+ Sir.
+ Int.
6
This connection "to exchange" allows
the insertion and the stop
both at a distance, both by the
implementing of the electronic key
of burglar central unit.
Programming
3
Programming
In order to work, mobile telephone dialer needs at least a telephone number in
Directory and that at least it is recorded a Message. To do this it is necessary to
approach to programming.
In st/by condition mobile telephone dialer visualizes on display a lightning
hyphen:
St/by
Code (default):
1 - 2 - 3 - 4
Local control
!
!
!
!
!
!
!
Press access code(default: "1234").
Mobile telephone dialer emit three "beep", and the written "L"appears who
lightning alternative to the hyphen, to indicate the modality of local
control.This condition persists for appoximately a minute, during which it is
possible follow next step to enter in programming, otherwise will be exited
automatically from local control.
Press "#8" to enter in programming: three horizontal hyphens appear to
indicate main menù of programming.
It is possible to enter in the several operations of programming brought
back pressing the relative number.
In whichever moment it is possible press "*" to return to main menù.
After about an inactive minute it exits from the programming without to
bring modifications.
Exiting from the programming it carries out the reset of outputs.
--
--
After 1 min.
Ignited
# - 8
Menù of
programming
After 1 min.
7
2in/2out telephone dialer with vocal messages - User Manual
From programming menù it is possible to approach to:
1.
2.
3.
4.
5.
6.
7.
8.
8
Directory
10 telephone numbers to which will be forward the Messages of Channels subsequently at the
activation of the 2 channels K1 and K2.
Alarm messages
2 vocal messages (of 15 seconds) relative to the activations of channels K1 and K2.
State messages
10 vocal messages (of 2 seconds) relative at several states of the channels of input and output that could
be interrogated upon request, calling mobile telephone dialer from remote and after having wait for its
answer, or also after having received a calling of alarm from mobile telephone dialer. So they are divided:
!
2 messages for the state of input INT:
INT:OFF / INT:ON
!
4 messages for the state of each input:
K1:OFF / K1:ON / K2:OFF / K2:ON
!
4 messages for the state of each output:
RELE1:OFF / RELE1:ON / RELE2:OFF / RELE2:ON
Inputs operation
Set up of inputs and of the conditions and the delays of activation.
Output operation
Set up of relay of output.
Timer
Set up of the delays of activation of the cycles of call and of outputs.
Parameters
Set up of the general parameters of operation.
Access codes
Set up of access codes "MASTER" and "OPERATOR”.
Programming
3.1
Directory
From main menù , pressing "1" it approach to Directory. Here it is possible memorize numbers of
telephone of mobiles or fixed net towards which will be send vocal messages of alarm.
After about an inactivity minute it exits from the programming without to bring modifications. In any
moments it is possible press "*" to return to main menù.
3.1.1
1.
2.
3.
After the access to the Directory it visualizes a "n"; press a number from "0" to "9" correspondent to the
position of directory to modify: lightning keyboarded number appears (if the position is empty) or fixed (if
it is full).
Press "#" to qualify modification.
It visualizes a "C" followed from "-" in attended that the channel to active to send the call to the present
telephone number ; press:
!
!
!
4.
5.
Insertion and elimination of telephone numbers
"1" to the activation of channel K1
"2" to the activation of channel K2
"0" to the activation of both channels K1 e K2.
After having qualified the channel, wait for the appearence of "-" lightning, and it is now possible to insert
the telephone number ; NOTE: key "*" can be used to put in a pause inside of the telephone number.
At the end of the input of the telephone number press "#" to confirm; mobile telephone dialer visualizes
again the present position of directory.
9
2in/2out telephone dialer with vocal messages - User Manual
6.
7.
Pressing again "#" it re enter in the modification of the position and it return to point 3. If in point 3. viene o
press still"#" appesrs "E" for a moment and it eliminates the number from the position; the number of the
position lightne to indicate that it is empty.
Press "*" to return to main menù.
3.1.2
1.
2.
3.
4.
10
Visualization of telephone numbers
After the access to the Directory it visualizes a "n"; press a number from "0" to "9" correspondent to the
position of directory to modify: lightning keyboarded number appears (if the position is empty) or fixed (if
it is full).
Press again the number of the selected position to qualify the visualization of the assigned channel and
of the telephone number ; for example it will be visualized:
C2-081123456
to indicate that number 081123456 of the present position will be called in case of activation of the
channel 2.
At the end of the sequence of the telephone number mobile telephone dialer executes a pause of about a
second and then visualizes again the present position of directory.
Press "*" to return to main menù.
Programming
3.2
Alarm messages
From main menù , pressing "2" it approach to Messages of Channel. In this phase it is possible to
manage the two vocal messagges (of 15 seconds) relative to the activation of the two channels.After about
an inactivity minute it exits from the programming without to bring modifications. In any moments it is
possible press "*" to return to main menù.
3.2.1
1.
2.
3.
4.
5.
6.
Recording / reproduction of channel messages
After the access to Alarm Messages it visualizes a "n": press "1" or "2" to select the relative messagges
to channel 1 or 2.
Una volta selezionato il canale è possibile effettuare la registrazione del messaggio mantenendo
premuto il tasto "#": compare un trattino in movimento.
At the end of the messagge leave again key "#" to stop recording. For every channel it is possible record
a messagge of the maximum duration of about 15 seconds, so the recording interrupt automatically.
After the recording, the messagge will be play back automatically; during the reproduction of the
messagge it will be visualized the number of the lightning channel on display.
At the end of the reproduction it will be visualized the number of the channel. Pressing again the number
of the channel the reproduction of message leave again.
Press "*" to return to main menù.
11
2in/2out telephone dialer with vocal messages - User Manual
3.3
State messages
From main menù , pressing "3” it approach to State Messages. In this phase it is possible to 10 vocal
messages (of 2 seconds) relative to several states of the channels of input and output that could be
interrogated upon request, calling from remote the number where the mobile telephone dialer is built in, and
after having wait for its replay, or also after having received a call of alarm from mobile telephone dialer.
After about an inactivity minute it exits from the programming without to bring modifications. In any
moments it is possible press "*" to return to main menù.
3.3.1
1.
After the access to State Messages it visualizes a "n"; press:
!
!
!
!
!
!
!
!
!
!
12
Recording / reproduction of state messages
"0" to programm the message INT:OFF
"1" to programm the message INT:ON
"2" to programm the message K1:OFF
"3”to programm the message K1:ON
"4" to programm the message K2:OFF
"5" to programm the message K2:ON
"6" to programm the message RELE1:OFF
"7" to programm the message RELE1:ON
"8" to programm the message RELE2:OFF
“9" to programm the message RELE2:ON
Programming
2.
3.
4.
5.
6.
Once selected the position is possible carry out the recording of the message pressing key "#".For the
entire time of the recording, an hyphen in motion appearce on display.
At the end of the messagge leave again key "#" to stop recording. For every positions it is possible
record a messagge of the maximum duration of about 2 seconds , so the recording interrupt
automatically.
After the recording, the messagge will be play back automatically; during the reproduction of the
messagge it will be visualized the number of the lightning channel on display.
At the end of the reproduction it will be visualized the number of the position. Pressing again the number
of the position the reproduction of message leave again.
Press "*" to return to main menù.
13
2in/2out telephone dialer with vocal messages - User Manual
3.4
Inputs operation
From main menù , pressing "4" it approach to the Inputs Operation. In this phase it is possible to manage
the two inputs K1and K2 relative to the activation of the two channels.
After about an inactivity minute it exits from programming without to bring modifications. In any moments
it is possible press "*" to return to main menù.
1.
2.
3.
After the access to Inputs Operation it visualizes a "n": press "1" o "2" to select input K1 or K2.
Press again the number of the channel to visualize present modality of operation input, or press "#" to
modify the set up.
It visualizes "-"; press the number of the modality to programm:
!
!
!
"0" = Not active
Channel will be not qualified.
"1" = Impulse NA
Channel is activated from the presence of a positive 12Vcc of the
duration at least of 0,1 seconds; the cycle of calls is started and
effectuated till the end,if it is not interrupted by commandos.
"2" = Impulse NC
Channel is activated from the absence of a positive 12Vcc of the
duration at least of 0,5 seconds; the cycle of calls is started and
effectuated till the end,if it is not interrupted by commandos.
12V
0,1sec min.
0
Impulso NA
12V
0,1sec min.
0
Impulso NC
14
Programming
!
!
!
!
!
4.
5.
"3" = LevelNA
12V
Channel is activate at the presence of a positive 12Vcc; the cycle of is
started and effectuated till the end,if it is not interrupted by commandos
or by the absence of the positive 12Vcc on input.
0
"4" = Level NC
Livello NA
Channel is active at the absence of the positive 12Vcc;the cycle calls
isstarted and effectuated till the end,if it is not interrupted by
12V
commandos or by te the restoration of the positive 12Vcc on input.
"5" = Impulse NA with INT
As Impulse NA but also conditionated from the presence of a positive
0
12Vccon input INT
Livello NC
"6" = Impulse NC with INT
As Impulse NC but also conditionated from the presence of a positive
12Vccon input INT
"7" = Level NA with INT
As Livello NA but also conditionated from the presence of a positive 12Vccon input INT
"8" = Level NC with INT
As Livello NC but also conditionated from the presence of a positive 12Vccon input INT
After selecting the modality, the number of programmed modality appears on display for few minutes,
then the number of the channel appears again.
Press "*" to return to main menù.
15
2in/2out telephone dialer with vocal messages - User Manual
3.5
Outputs operation
From main menù , pressing "5" it approach to the outputs Operation. In this phase it is possible to
manage the operation of the two outputs relè.
After about an inactivity minute it exits from programming without to bring modifications. In any moments
it is possible press "*" to return to main menù..
1.
2.
3.
After the access to outputs Operation it visualizes a "n": press "1" o "2" to selecte output relè 1 or 2.
Press again the number of the channel to visualize present modality of operation of the output,or press
"#" to modify the set up.
It visualizes "-"; press the number of the modality to programm:
!
!
16
"0" = ON/OFF
Commando "ON" actives the relè of output (contacts closure C/NA); commando "OFF" does not
active the relè of output (contacts opening C/NA).
"1" = ON/OFF with input INT
Commando "ON" actives the relè of output (contacts closure C/NA) if tension is only absent on
input INT (for example.: burglar central unit not inserted) and it has not effect if tension is present
on input INT (for example.: burglar central unit already inserited)
Commando "OFF" disactives the relè of output (contacts opening C/NA)if tension is only present
on input INT (for example.: burglar central unit inserited) and it has not effect if tension is absent on
input INT (for example.: burglar central unit already not inserted).
This option is used with whichever centrals with insertion at mechanical key that, for the insertion,
needs the closing of the connections "ON/OFF" in clamps.
Programmazione
!
!
!
!
!
!
!
!
"2" = ON/OFF with input K1
As ON/OFF with input INT but conditionated from input K1.
"3" = ON/OFF with input K2
As ON/OFF with input INT but conditionated from input K2.
"4" = PULSE
Commandos "ON" and "OFF" active the relè of output (contacts closure C/NA for the time set up in
programming).
"5" = PULSE with input INT
Commando "ON" active the relè of output (contacts closure C/NA for the time set up in
programming) if tension is only absent on input INT (for example.: burglar central unit not inserted)
and it has not effect if tension is present on input INT (for example.: burglar central unit already
inserited).
Commando "OFF" reactives the relè of output (contacts closure C/NA for the time set up in
programming) if tension is only present on inpu INT (for example.: burglar central unit inserted) and
it has not effect if tension is absent on input INT (for example.: burglar central unit already not
inserted).
This option is used with whichever centrals with electronic insertion, for example central TM600P,
that, for the insertion, needs an impulse of closing of the connections "ON/OFF" in clamps.
"6" = PULSE with input K1
As PULSE with input INT but conditionated from input K1
"7" = PULSE with input K2
As PULSE with input INT but conditionated from input K2
"8" = Toggle
Commandos "ON" and "OFF" invert the state of the relè of output.
17
2in/2out telephone dialer with vocal messages - User Manual
4.
5.
After selecting the modality, the number of programmed modality appears on display for few minutes,
then the number of the channel appears again.
Press "*" to return to main menù.
WARNING: When it exit from setup outputs reset.
18
Programmazione
3.6
Temporizations
From main menù , pressing "6" it approach at the regulation of the temporizations. In this phase it is
possible to regulate some temporizations that elapse, for example, between the activation of an input and the
effective activation of the cycles of calls.
After about an inactivity minute it exits from programming without to bring modifications. In any moments
it is possible press "*" to return to main menù.
1.
After the access to the Temporizations it visualizes a "n"; press the number of the temporization to
programm:
"1" = duration in seconds between the activation of the channel 1and the start of the cycle of calls;
"2" = duration in seconds between the activation of the channel 2and the start of the cycle of calls;
"3" = duration in tenths of seconds of activation of the relè output 1 (if programmed in
"PULSE"modalities;
!
"4" = duration in tenths of seconds of activation of the relè output 1 (if programmed in
"PULSE"modalities;
Press again the number of the temporization to visualize present set up.
It visualizes on display one for time the four figures of the number of seconds or tenths of seconds that
are loaded in the timer, spaced out from a short pause. At the end of the visualization display shows the
number of the selected and it return in the phase of selection of timer.
To modify set up value, press key "#".
It visualizes "-"; press in sequece the four figures of the number of seconds (or of tenths of seconds) to
set up. NOTE:It is always necessary to press the four figures of the number to set up.
19
!
!
!
2.
3.
4.
5.
2in/2out telephone dialer with vocal messages - User Manual
6.
7.
20
If for example it wants to set up at 3,5 seconds the timer for the temporization of the impulse on output 2,
after having selected the timer 4 press "#0035".
On display appears the number of the selected timer and it returns at point 1.
Press "*" to return to main menù.
Programming
3.7
Operation parameters
From main menù , pressing "7" to approach to the Operation parameters.
After about an inactivity minute it exits from programming without to bring modifications. In any moments it is
possible press "*" to return to main menù. On displaycharacter "n” flash in attend of the selection of the
parameter to visualize or to modify:
1.
2.
Number of repetition cycles:
Telephone selection:
3.
4.
Number of repetition of the message:
Visualization of the number during the composing:
5.
Number of blasts before the answer:
from 1to 5
0=decadica (at impulses)
1=DTMF (at tones)
from 1 to 5.
0=visualize
1=not visualize
from 1 to 9
0=not answer.
NOTE: other telephone equipment at automatic answer connected to the output of the mobile telephone
dialer (for example.: A telephone secretariat ) can be programmed so as to answer ot an inferior number
of blasts regarding the mobile telephone dialer; in this way, if we mean make us answer from mobile
telephone dialer is sufficient carry out a single blast before, and following (after minimum 8 seconds and
maximum 30 seconds) a second blast to which mobile telephone dialer wil answer iimediately.
Press again the selected parameter to visualize the set up: ondisplay the set up value appears for a
second and then returns to the selection modality parameter.
21
2in/2out telephone dialer with vocal messages - User Manual
To modify the set up value press before "#" so an hyphen appears on display and then press the wished
value . After a moment the number of selected parameter appears again on display and return in phase
parameter selection.
3.8
Modification access codes
From set up menù press "8" :on display character "n" appears.
Press 1 for Master code or 2 for Operator code.
Press key "#" - on display appears the hyphen.
Press the four numbers of the code display visualizes pressed numbers and then return to the modality of
selection of the code.
It is not possible to visualize a memorized code, but only replace it with a new code.
With the operator code it is possible to stop the calls, command or to query the outputs and the inputs and
active alive voice operation, but it is not possible to modify the setup or put mobile telephone dialer in the
modality "out of order”.
22
Operating
4
Operating
4.1
Operation general description
The activation of a channel by relative input generates one or more cycles of calls in sequence towards
telephones of fixed net or mobiles memorized in the Directory and associated to the channel. It follows the
forwarding of the Message of channel relative repeated more times. After having received the call of allarm of
mobile telephone dialer it is possible, by DTMF (keyboard of the remote telephone), to check out the state of
inputs and outputs listening to the state Messages, and moreover it is possible command the outputs; this
functionality is also possible calling in any moments mobile telephone dialer and after having attended the
automatic answer (see 3 Programming - 3.7 Parameters - Point 5 a pag 20), or from local keyboard .
NOTE:
Command "##" effetuated from a remote telephone excludes the call to that number from
thefollowing repetitions of the cycle of calls in course. This commando is accepted from mobile
telephone dialer also without have pressed an access code to the commandos. So it is possible
insert at the end of the Message of channel the following caption:"... Press twice cancelletto to
not receive more this message”.
23
2in/2out telephone dialer with vocal messages - User Manual
4.2
Commandos
To approach to the commandos it is necessary press:
! Master code (1234) to approach to all commandos, comprised the programming;
! Operator code (5678) to approach only to a part of the commandos.
On display appears a "L" lightning if the control is effectuated from local keyboard, or "E" if the control is
effectuated from a telephone at tones (DTMF) connected in remote; three beep of confirmation will be
emitted.
In remote control can happen to press the code while it listen to the message of allarm. So the code will
not be recognized from mobile telephone dialer ( three beep of confirmation will not be emitted) so it is
necessary press "*"and repeats the access code to commandos.
In local control mobile telephone dialer finishes at the same time all the operations of calls in course, so
the three of the following commandos will be available only in the remote control :
#0
It finishes call in course (only in the remote control)
After three beep of confirmation, mobile telephone dialer finishes the call and continues with
eventual other calls of the cycle in course.
#1
It finishes the cycle of calls (only in the remote control)
After three beep of confirmation, mobile telephone dialer finishesil cycle of calls in course, and
continues eventual other cycles of calls bound torether to the other channel.
#2
24
It finishes all the cycles in execution (only in the remote control)
Dopo una serie di beep di conferma il combinatore termina tutti i cicli di chiamata in corso.
Operating
#3
Commando and interrogation state output
After three beep of confirmation, it is possible use this commando from the local keyboard or from a
connected telephone in remote both during a call of allarm both calling directly mobile telephone
dialer. Select one of the two outputs with keys "1" or "2" and press:
!
the number of selected channel again ("1" or "2") to know the state of the channel
!
"7" to give a commando of ON
!
"9" to give a commando of OFF
Mobile telephone dialer executes the commando according to the modality of operation of the
outputs (par. 3.5 to pag. 16). In the remote control, at every commandos it is possible listen by the
telephone receiver the relative message to the state of the commanded output or eventuallyof the
input to which makes reference.
#4
Interrogazione stato inputs
After three beep of confirmation, it is possible use this commando from the local keyboard or from
a connected telephone in remote both during a call of allarm both calling directly mobile telephone
dialer. Press:
!
"1" to interrugate the state of the input K1
!
"2" to interrugate the state of the input K2
!
"3" to interrugate the state of the input INT
#5
Activation vocal comunication
During a connection with a remote telephone, active the modality commandos inserting a code and
press "#5". In this way it is possible listen to the sounds that are picked up to the microphone of
mobile telephone dialer. With key "9" is possible to speack on the receiver and get listen by the
25
2in/2out telephone dialer with vocal messages - User Manual
speaker on mobile telephone dialer, while with key "7" is possible return in hearing modality . Vocal
comunication lasts about 15 seconds; if it wishes to extend this time is necessary press a number on
the telephone keyboard to leave again the temporization. In any case it cannot listen and speack at
the same time.
26
#6
Out of order (only Master code)
From commandos modality press "#6". Mobile telephone dialer does not active itself carrying itself
out of order and indicating with 6 beeps . In this condition the activation of an input generates any
cycle of calls. The condition is marked on display from the letter "H" lightning. But mobile telephone
dialer continues to answer to eventual external calls to accept other commandos.
#7
In of order(only Master code)
After having activated commandos modality , press "#7" to carry mobile telephone dialer in full
activity.
#8
Programming (only Master code)
With commando "#8" it approach to the programming come sopra illustrato.
#9
Test calling (only Master code)
From commandos modality press "#9". So choose the memorized number to test pressing directly
relative figure of the directory. Immediately the call will start in monitor modality (live speaker) and
will be executed a regular cycle of calls. To break the call before the natural completion of the cycle
press still MASTER code.
Appendice A
Appendix A
Values of default
Modality operation channel 1
Modality operation channel 2
Modality output K1
Modality output K2
5
3
1
0
Timer delay channel 1
Timer delay channel 2
0
0
Duration Pulse Output K1
Duration Pulse Output K2
10
10
MASTER code
OPERATOR code
1234
5678
Parameter 1
Parameter 2
Parameter 3
Parameter 4
Parameter 5
3
1
3
0
7
Impulse NA with INT
Level NA
ON-OFF with input INT
ON-OFF
Repetition cycles
Modality DTMF
Repetition messages
Visualization called number qualified
Squilli per risposta automatica
27
2in/2out telephone dialer with vocal messages - User Manual
Other temporization of system
Duration attended to recall for function Bypass Fax-Secretariat
Maximum duration . Attended recall after first timing
Pause Duration
Break between end selection and sending message
Max durata attended commandos after sending message
Break between sending message
Break between calls
Duration sensibility key SETUP
28
8 seconds
20 seconds
2 seconds
5 seconds
5 seconds
2 seconds
5 seconds
5 seconds
406BDE-1.01
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement