Chicago Electric Owner's Manual & Safety Instructions Owner`s manual

Chicago Electric Owner's Manual & Safety Instructions Owner`s manual
Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the
manual near the assembly diagram (or month and year of purchase if product has no number). Keep this
manual and the receipt in a safe and dry place for future reference.
REV 14i
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2008 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product
described herein. Tools required for assembly and service may not be included.
Read this material before using
this product. Failure to do so
can result in serious injury.
SAVE THIS MANUAL.
Table of Contents
Safety..................................................3 Maintenance...................................... 13
Safety
Specifications...................................... 9 Parts List and Diagram...................... 14
Setup...................................................9 Warranty............................................16
Operation........................................... 11
WARNING SYMBOLS AND DEFINITIONS
Setup
This is the safety alert symbol. It is used to
alert you to potential personal injury hazards.
Obey all safety messages that follow this
symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
Operation
Indicates a hazardous situation
which, if not avoided, could result
in minor or moderate injury.
Addresses practices not related
to personal injury.
Maintenance
Page 2
For technical questions, please call 1-888-866-5797.
Item 97626
IMPORTANT SAFETY INFORMATION
Safety
General Power Tool Safety Warnings
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term ″power tool″ in the warnings refers to your
mains-operated (corded) power tool.
1. Keep work area clean and well lit. 3. Keep children and bystanders
Cluttered or dark areas
away while operating a
invite accidents.
power tool.
Distractions can cause
2. Do not operate power tools
you to lose control.
in explosive atmospheres,
Setup
Work area safety
such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which
may ignite the dust or fumes.
3. Do not abuse the cord. Never
use the cord for carrying, pulling
or unplugging the power tool.
Keep cord away from heat, oil,
sharp edges or moving parts.
Damaged or entangled cords
increase the risk of electric shock.
2. Do not expose power tools
to rain or wet conditions.
Water entering a power tool will
increase the risk of electric shock.
4. If operating a power tool in a
damp location is unavoidable,
use a Ground Fault Circuit
Interrupter (GFCI) protected
supply. Use of a GFCI reduces
the risk of electric shock.
Item 97626
For technical questions, please call 1-888-866-5797.
Page 3
Maintenance
1. Power tool plugs must match
the outlet. Never modify the
plug in any way. Do not use any
adapter plugs with grounded
power tools. Unmodified plugs
and matching outlets will
reduce risk of electric shock.
Operation
Electrical safety
Personal safety
Safety
Setup
Operation
1. Stay alert, watch what you are
5. Do not overreach. Keep proper
doing and use common sense
footing and balance at all times.
when operating a power tool.
This enables better control of the
Do not use a power tool while you
power tool in unexpected situations.
are tired or under the influence
6. Dress properly. Do not wear
of drugs, alcohol or medication.
loose clothing or jewelry.
A moment of inattention while
Keep your hair, clothing and
operating power tools may result
gloves away from moving parts.
in serious personal injury.
Loose clothes, jewelry or long hair
2. Use personal protective
can be caught in moving parts.
equipment. Always wear eye
7. If devices are provided for the
protection. Safety equipment
connection of dust extraction and
such as dust mask, non-skid
collection facilities, ensure these
safety shoes, hard hat, or
are connected and properly used.
hearing protection used for
Use of these devices can
appropriate conditions will
reduce dust‑related hazards.
reduce personal injuries.
8. Only use safety equipment
3. Prevent unintentional starting.
that has been approved by an
Ensure the switch is in the
appropriate standards agency.
off‑position before connecting
Unapproved safety equipment
to power source, picking up or
may not provide adequate
carrying the tool.
protection. Eye protection must be
Carrying power tools with your
ANSI‑approved and
finger on the switch or energizing
breathing protection must be
power tools that have the
NIOSH‑approved for the specific
switch on invites accidents.
hazards in the work area.
4. Remove any adjusting
key or wrench before
turning the power tool on.
A wrench or a key left attached to
a rotating part of the power tool
may result in personal injury.
Maintenance
Page 4
For technical questions, please call 1-888-866-5797.
Item 97626
5. Maintain power tools. Check
for misalignment or binding
of moving parts, breakage of
parts and any other condition
that may affect the power tool’s
operation. If damaged, have
the power tool repaired before
2. Do not use the power tool if the
use. Many accidents are caused
switch does not turn it on and off.
by poorly maintained power tools.
Any power tool that cannot be
controlled with the switch is
6. Keep cutting tools sharp and
dangerous and must be repaired.
clean. Properly maintained
cutting tools with sharp cutting
3. Disconnect the plug from
edges are less likely to bind
the power source before
and are easier to control.
making any adjustments,
4. Store idle power tools out of
the reach of children and do not
allow persons unfamiliar with the
power tool or these instructions
to operate the power tool.
Power tools are dangerous in
the hands of untrained users.
7. Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking
into account the working
conditions and the work to be
performed. Use of the power
tool for operations different from
those intended could result
in a hazardous situation.
Operation
changing accessories,
or storing power tools.
Such preventive safety measures
reduce the risk of starting the
power tool accidentally.
Setup
1. Do not force the power
tool. Use the correct power
tool for your application.
The correct power tool will do
the job better and safer at the
rate for which it was designed.
Safety
Power tool use and care
Service
Maintenance
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
Item 97626
For technical questions, please call 1-888-866-5797.
Page 5
Rotary Tool Safety Warnings
Safety
1. Maintain labels and nameplates
on the tool. These carry
important safety information.
If unreadable or missing,
contact Harbor Freight Tools
for a replacement.
2. Avoid unintentional starting.
Prepare to begin work before
turning on the tool.
Setup
3. Do not lay the tool down until it
has come to a complete stop.
Moving parts can grab the surface
and pull the tool out of your control.
4. When using a handheld power tool,
maintain a firm grip on the tool with
both hands to resist starting torque.
5. Do not depress the spindle lock
when starting or during operation.
Operation
6. Do not leave the tool unattended
when it is plugged into an
electrical outlet. Turn off the
tool, and unplug it from its
electrical outlet before leaving.
7. This product is not a toy.
Keep it out of reach of children.
• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures
varies, depending on how often
you do this type of work. To reduce
your exposure to these chemicals:
work in a well ventilated area,
and work with approved safety
equipment, such as those dust
masks that are specially designed
to filter out microscopic particles.
(California Health & Safety Code
§ 25249.5, et seq.)
9. WARNING: The cord of this
product contains lead and/
or di (2-ethylhexyl) phthalate
(DEHP), chemicals known to
the State of California to cause
cancer, and birth defects or other
reproductive harm. Wash hands
after handling. (California Health
& Safety Code § 25249.5, et seq.)
10.People with pacemakers should
consult their physician(s)
before use. Electromagnetic
fields in close proximity to heart
pacemaker could cause pacemaker
interference or pacemaker failure.
Maintenance
8. WARNING: Some dust created by
11.The warnings, precautions,
power sanding, sawing, grinding,
and instructions discussed in
drilling, and other construction
this instruction manual cannot
activities, contains chemicals known
cover all possible conditions and
to the State of California to cause
situations that may occur. It must
cancer and birth defects or other
be understood by the operator
reproductive harm. Some examples
that common sense and caution
of these chemicals are:
are factors which cannot be
• Lead from lead-based paints
built into this product, but must
• Crystalline silica from bricks and
be supplied by the operator.
cement or other masonry products
Page 6
For technical questions, please call 1-888-866-5797.
Item 97626
1. Anyone using vibrating tools
regularly or for an extended
period should first be examined
by a doctor and then have
regular medical check-ups to
ensure medical problems are
not being caused or worsened
from use. Pregnant women or
people who have impaired blood
circulation to the hand, past
hand injuries, nervous system
disorders, diabetes, or Raynaud’s
Disease should not use this tool.
If you feel any symptoms
related to vibration (such as
tingling, numbness, and white
or blue fingers), seek medical
advice as soon as possible.
2. Do not smoke during use.
Nicotine reduces the blood supply
to the hands and fingers, increasing
the risk of vibration-related injury.
3. Wear suitable gloves to reduce
the vibration effects on the user.
4. Use tools with the lowest vibration
when there is a choice.
5. Include vibration-free periods
each day of work.
Setup
This tool vibrates during use.
Repeated or long‑term exposure
to vibration may cause temporary
or permanent physical injury,
particularly to the hands, arms
and shoulders. To reduce the risk
of vibration-related injury:
Safety
Vibration Safety
6. Grip tool as lightly as possible
(while still keeping safe control of it).
Let the tool do the work.
Maintenance
SAVE THESE INSTRUCTIONS.
Operation
7. To reduce vibration, maintain
the tool as explained in this
manual. If any abnormal vibration
occurs, stop use immediately.
Item 97626
For technical questions, please call 1-888-866-5797.
Page 7
Grounding
Safety
TO PREVENT ELECTRIC SHOCK AND DEATH FROM
INCORRECT GROUNDING WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. Do not modify the power cord plug
provided with the tool. Do not use the tool if the power cord or plug is
damaged. If damaged, have it repaired by a service facility before use. If
the plug will not fit the outlet, have a proper outlet installed by a
qualified electrician.
Setup
This tool’s power adapter may
be used in either of the 120 volt
outlets shown in the preceding
illustration. (See Figure A.)
Figure A: Outlets for 2-Prong Plug
Operation
Extension Cords
Note: Extension cords must not be used with this item’s power adapter.
Symbology
Table A: Symbology
Double Insulated
Canadian Standards
Association
Underwriters
Laboratories, Inc.
Maintenance
V~
A
Volts Alternating Current
Amperes
n
0 No Load Revolutions
xxxx/
per Minute (RPM)
m i n .
Page 8
Table A: Symbology
WARNING marking
concerning Risk of Eye Injury.
Wear ANSI‑approved safety
goggles with side shields.
Read the manual before
set-up and/or use.
WARNING marking
concerning Risk of Fire.
Do not cover
ventilation ducts.
WARNING marking
concerning Risk of
Electric Shock.
Maintain Power cord properly.
For technical questions, please call 1-888-866-5797.
Item 97626
12VDC
Adapter Input
120V~ / 60Hz
Rotation Speed
16,000 RPM
Collet Size
1mm, 3mm, 3/32″,
and 1/8″
Setup
Tool Input
Safety
Specifications
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY
INFORMATION section at the beginning of this
manual including all text under subheadings
therein before set up or use of this product.
1/8″ Shank with
Buffing Wheel
Power Switch
Lock Button
Maintenance
Collar
Operation
Functions
Item 97626
For technical questions, please call 1-888-866-5797.
Page 9
Accessories
Safety
Note: Refer to “Parts List and
Diagram” on page 14 for
accessory illustrations.
• Use the Diamond Burr
Bits (4) to drill hard, brittle
materials, such as tile.
• Use the Mounted Stones (5)
for sharpening cutting tools,
screwdrivers etc, deburring metal
after cutting, and removing excess
material on metal and ceramics.
Setup
• Use the Sanding Drums (6)
to smooth out rough areas
on soft materials.
• Use the Cut-off Wheels (7)
for cutting, carving and
slotting materials.
• Use the Buffing Wheels (8)
for polishing.
• Use the Wire Wheels (9) to
clean dirty or rusted surfaces.
• Use the Whet Stone (10)
for sharpening.
• Use the Drill Bits (11) to
bore small holes.
• Mandrels are the shanks
with a threaded or screw
head. Use them with the
cut-off wheels, polishing
wheels, and sanding discs.
The shank without threads on the
end is for the felt polishing wheels.
Operation
Maintenance
Page 10
For technical questions, please call 1-888-866-5797.
Item 97626
Read the ENTIRE IMPORTANT SAFETY INFORMATION section
at the beginning of this manual including all text under
subheadings therein before set up or use of this product.
Tool Set Up
Safety
Operating Instructions
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool to its “OFF” position and unplug
the tool from its electrical outlet before installing accessories.
4. Place the Collar over the Collet,
but do not tighten yet.
2. Choose the right
Accessory for the job (see
“Accessories” on page 10)
and the Collet that matches
the Accessory’s shank.
5. Insert the Accessory’s
shank into the Collet.
3. Insert the Collet into the Rotary Tool.
Setup
1. Hold the Lock Button down
and unscrew the Collar.
6. Hold the Lock Button down,
and tighten the Collar.
7. Release the Lock Button. Pull on
the Shank to ensure that it is secure.
Maintenance
1. Designate a work area that is clean 3. Secure loose work pieces using
and well-lit. The work area must
a vise or clamps (not included) to
not allow access by children or pets
prevent movement while working.
to prevent distraction and injury.
4. There must not be objects, such
2. Route the power cord along a
as utility lines, nearby that will
safe route to reach the work area
present a hazard while working.
without creating a tripping hazard
or exposing the power cord to
possible damage. The power
cord must reach the work area
with enough extra length to allow
free movement while working.
Operation
Work Piece and Work Area Set Up
Item 97626
For technical questions, please call 1-888-866-5797.
Page 11
General Operating Instructions
Safety
1. Plug the Power Adapter
into a standard, grounded
120V electrical outlet.
2. Connect the Rotary Tool
to the Power Adapter.
3. Turn the Power Switch “ON” and
allow the Rotary Tool to come up to
full speed before beginning work.
4. Contact the material lightly.
Do not press hard on the tool
while working; allow the tool to
work at its own pace. It is better
to make several shallow passes
than to make one deep pass.
5. To prevent accidents, turn off
the tool and disconnect its
power supply after use. Clean,
then store the tool indoors
out of children’s reach.
Setup
Operation
Maintenance
Page 12
For technical questions, please call 1-888-866-5797.
Item 97626
User-Maintenance Instructions
Safety
Procedures not specifically explained in this manual
must be performed only by a qualified technician.
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Turn the Power Switch of the tool to its “OFF” position
and unplug the tool from its electrical outlet before any
inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration
occurs, have the problem corrected before further use.
Setup
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general condition of the
tool. Check for loose screws, misalignment or binding of moving
parts, cracked or broken parts, damaged electrical wiring, and
any other condition that may affect its safe operation.
2. AFTER USE, clean external surfaces of the tool with clean, moist cloth.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS
LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE
TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES
ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER
THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT,
OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE
PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS,
AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND
LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL
PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF
HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Item 97626
For technical questions, please call 1-888-866-5797.
Page 13
Operation
WARNING! If the supply cord of this power tool is damaged,
it must be replaced only by a qualified service technician.
Maintenance
3.
Parts List and Diagram
Safety
Parts List
Part
1
2
3
4
5
6
Description
Rotary Tool
Power Adapter
Collet
Diamond Burr Bit
(3/32″ Shank)
Mounted Stone
(3/32″ Shank)
Sanding Drum
(3/32″ Shank)
Qty
1
1
4
20
Part
7
8
9
10
10
2
11
Description
Cut-off Wheel
(1/8″ Shank)
Buffing Wheel
(1/8″ Shank)
Wire Wheel
(1/8″ Shank)
Whet Stone
Drill Bit (1mm,
3mm, 3/32″ & 1/8″)
Qty
25
4
2
1
4
Setup
Operation
Maintenance
Record Serial Number Here:
Note: If product has no serial
number, record month and
year of purchase instead.
Page 14
Note: Some parts are listed and
shown for illustration purposes
only, and are not available
individually as replacement parts.
For technical questions, please call 1-888-866-5797.
Item 97626
Assembly Diagram
Safety
1
7
8
3
Setup
2
9
4
Operation
10
5
11
Maintenance
6
Item 97626
For technical questions, please call 1-888-866-5797.
Page 15
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet
high quality and durability standards, and warrants to the original purchaser that
this product is free from defects in materials and workmanship for the period
of 90 days from the date of purchase. This warranty does not apply to damage
due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or
alterations outside our facilities, criminal activity, improper installation, normal
wear and tear, or to lack of maintenance. We shall in no event be liable for
death, injuries to persons or property, or for incidental, contingent, special or
consequential damages arising from the use of our product. Some states do
not allow the exclusion or limitation of incidental or consequential damages, so
the above limitation of exclusion may not apply to you. THIS WARRANTY IS
EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us
with transportation charges prepaid. Proof of purchase date and an explanation
of the complaint must accompany the merchandise. If our inspection verifies
the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you
with a replacement. We will return repaired products at our expense, but if we
determine there is no defect, or that the defect resulted from causes not within
the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may
also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement