Dacor MRWD30 Specifications
ERWD, EWD, IWD, MRWD, MWDV, MWDH,
OWD and PWD
Document # PG02 - 002
Revised 11/19/09
24”, 27”, 30”, 36”,
Wide Warming Drawers
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
ERWD
EWD
3 1/2"
(89 mm)
3 7/16"
(87 mm)
1 1/8"
(29 mm)
1"
(25 mm)
PLANNING
GUIDE
Electrical Circuit Required
Total Connected Load
120 Vac, 60 Hz, 15 Amps.
grounded, dedicated circuit
4.0 Amps.
@ 120 Vac, 60 Hz
MRWD30B
(only)
1 7/16"
(37 mm)
1"
(25mm)
All other
MRWD series
Page 1/3
10 1/8"
(257 mm)
MWDH/V
3 1/4"
(83 mm)
1"
(25 mm)
PWD
2 1/4"
(57 mm)
A
1"
(25 mm)
Handle Dimensions - side view
Drawer Face Dimensions
(MWD Series Shown)
B
C
Chassis
Mounting
Hole 9 Places
40" (1016 mm)
3 prong
120 Vac power cord
9"
(229 mm)
1/2"
(13 mm)
23 3/8"
(594 mm)
10"
(254 mm)
Chassis without
drawer inserted
5/64"
(2mm)
Drawer open
1/2"
(13 mm)
23 13/16
(605 mm)
Chassis Dimensions
(A) Drawer Face
Width
(B) Chassis Face
Width
(C) Chassis
Width
ERWD30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
EWD24
24” (610 mm)
23 5/8” (600 mm)
22 1/4” (565 mm)
EWD27
27” (686 mm)
26 5/8” (676 mm)
25 1/4” (641 mm)
EWD30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
EWD36
36” (914 mm)
35 5/8” (905 mm)
34 1/4” (870 mm)
MRWD27
27” (686 mm)
26 5/8” (676 mm)
25 1/4” (641 mm)
MRWD30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
MWDH27
27” (686 mm)
26 5/8” (676 mm)
25 1/4” (641 mm)
MWDH30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
MWDV27
27” (686 mm)
26 5/8” (676 mm)
25 1/4” (641 mm)
MWDV30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
PWD27
27” (686 mm)
26 5/8” (676 mm)
25 1/4” (641 mm)
PWD30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
Model
Overall Dimensions - Top View
(EWD Series Shown)
For PWD series models:
The Dacor color palette has been developed and implemented
throughout our product offerings in order to provide designers
and customers with a coordinating suite of products. All of our
Dacor Preference products compliment the design aesthetic
of today's kitchens as well as one another. Due to the inherent
nature of color rendition, the variation of materials used to
assemble these handcrafted products and manufacturing
production tolerances, variation based upon ambient and natural
lighting conditions as well as surrounding surface color and
texture may cause noticeable variation in saturation. These
Dacor products are intended to coordinate with one another and
noticeable differentiation may be apparent if units are installed
directly adjacent to one another.
www.Dacor.com
Phone: (800) 793-0093
Warming Drawer Overall Dimensions
Specifications are subject to change without notice.
See installation instructions for additional details.
2.1
ERWD, EWD, IWD, MRWD, MWDV, MWDH,
OWD and PWD
Document # PG02 - 002
Revised 11/19/09
24”, 27”, 30”, 36”,
Wide Warming Drawers
Product tolerances: ±1/16” (±1.6 mm) unless otherwise stated
C
B
Page 2/3
PLANNING
GUIDE
Electrical Circuit Required
Total Connected Load
120 Vac, 60 Hz, 15 Amps.
grounded, dedicated circuit
4.0 Amps.
@ 120 Vac, 60 Hz
E
Chassis
5/16”
(8 mm)
D
A
Drawer open
Drawer Face Dimensions
(IWD/OWD Series Shown)
F
40" (1016 mm)
3 prong
120 Vac power cord
Mounting hole,
9 places
Overall Dimensions - IWD/OWD Series
Top View
**
**
**
**
G
Chassis without
drawer installed
** = OWD24 mounting holes
Chassis Dimensions
(IWD/OWD Shown)
Model
(A) Dimension
Drawer Face Width
(B) Dimension
Chassis Width
(C) Dimension
Chassis Face
Width
IWD24
22 5/16” (567 mm)
22 1/4” (565 mm)
22 3/8” (568 mm)
IWD27
25 5/16” (643 mm)
25 1/4” (641 mm)
25 3/8” (645 mm)
IWD30
28 5/16” (719 mm)
28 1/4” (718 mm)
28 3/8” (721 mm)
OWD24
22 1/2” (571 mm)
22 1/2” (571 mm)
22 1/2” (571 mm)
www.Dacor.com
Phone: (800) 793-0093
(D)
Dimension
Drawer Face
Height
(E)
Dimension
Chassis
Depth
(F)
Dimension
Drawer
Depth
(G)
Dimension
Chassis
Height
8 15/16”
(227 mm)
23 3/8”
(594 mm)
23 13/16”
(605 mm)
9 1/16”
(230 mm)
11 7/8”
(302 mm)
20”
(508 mm)
18”
(457 mm)
11 7/8”
(302 mm)
Specifications are subject to change without notice.
See installation instructions for additional details.
2.2
ERWD, EWD, IWD, MRWD, MWDV, MWDH,
OWD and PWD
Document # PG02 - 002
Revised 11/19/09
24”, 27”, 30”, 36”
Wide Warming Drawers
Cabinet/countertop tolerances: +1/16” (+1.6 mm) -0 unless otherwise stated
Warming drawer
36" Typ.
(914 mm)
Warming drawer
C
PLANNING
GUIDE
warning
•
Observe all governing codes and ordinances
during planning and installation. Contact your
local building department for further information.
•
This appliance must be installed in accordance
with the accompanying installation instructions.
3/4" Min.*
(19 mm)
D
120 Vac
electrical
outlet
Page 3/3
C
3/4" Min.*
(19 mm)
Mounting platform must be 3/4" (19 mm) thick
and support 100 lbs.
A
B
27"/30"/36"
Dacor
single oven
1 1/2" (38 mm)
Typical countertop
Cooktop
D
Warming drawer 120 Vac
elect.
Warming drawer
C
D
Warming drawer 120 Vac
elect.
Toe kick
A
Model
ERWD30
EWD24
EWD27
EWD30
EWD36****
IWD24****
IWD27****
IWD30****
MRWD27
MRWD30
MWDH27
MWDH30
MWDV27
MWDV30
OWD24*****
PWD27
PWD30
36" Typ.
(914 mm)
C
A
B
C
3/4” Min.*
(19 mm)
120 Vac
electrical
outlet
3/4" Min.*
(19 mm)
(A) Cutout Width
28 1/2” (724 mm)
22 1/2” (572 mm)
25 1/2” (648 mm)
28 1/2” (724 mm)
34 1/2” (876 mm)
22 1/2” (572 mm)
25 1/2” (648 mm)
28 1/2” (724 mm)
25 1/2” (648 mm)
28 1/2” (724 mm)
25 1/2” (648 mm)
28 1/2” (724 mm)
25 1/2” (648 mm)
28 1/2” (724 mm)
22 5/8” (575 mm)
25 1/2” (648 mm)
28 1/2” (724 mm)
(B) Min. Width to
Adjacent Doors/
Drawers
30 1/4” (768 mm)*
24 1/4” (616 mm)*
27 1/4” (692 mm)*
30 1/4” (768 mm)*
36 1/4” (921 mm)*
**
**
**
27 1/4” (692 mm)*
30 1/4” (768 mm)*
27 1/4” (692 mm)*
30 1/4” (768 mm)*
27 1/4” (692 mm)*
30 1/4” (768 mm)*
24 1/4” (616 mm)***
27 1/4” (692 mm)*
30 1/4” (768 mm)*
(C) Cutout Height
(D) Min. Vertical Gap
Between Cutouts
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
11 15/16” (303 mm)
9 1/8” (232 mm)
9 1/8” (232 mm)
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
NA
NA
NA
NA
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
1 1/4” (32 mm)*
NA
1 1/4” (32 mm)*
1 1/4” (32 mm)*
Min. Cutout Depth
24” (610 mm)
20 1/8” (511 mm)
24” (610 mm)
* Bare minimum spacing to allow for ventilation and avoid scraping on EWD, MW and PWD series models.
** On IWD series models or OWD24 without the optional front panel kit: The chassis and the drawer faceplate are smaller than the cutout.
The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must exceed the appropriate cutout
dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom and sides from the custom front panel
edge to prevent scraping against adjacent doors, drawers and the countertop.
*** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and below cutout is 3/4”
minimum. See ** above for OWD24 with custom front panel.
**** This model cannot be installed above or below another warming drawer (any type).
***** Model OWD24 cannot be installed above, below or adjacent to a wall oven or warming drawer (any type).
www.Dacor.com
Phone: (800) 793-0093
Specifications are subject to change without notice.
See installation instructions for additional details.
2.3
Installation Instructions
Warming Drawer
Models:
Part No. 102345 Rev. L
ERWD30, EWD24, EWD27, EWD30, EWD36, IWD24,
IWD27, IWD30, MRWD27, MRWD30, MWDH27,
MWDH30, MWDV27, MWDV30, OWD24, PWD27,
PWD30
All specifications are subject to change without notice. Dacor ® assumes no liability for changes to specifications.
© 2007 Dacor, all rights reserved.
Table of Contents
Before You Begin............................................................... 1
Important Safety Instructions........................................... 1
General Safety Precautions.............................................. 2
Installation Specifications................................................. 3
Verifying the Package Contents........................................ 3
Installation Planning.......................................................... 3
Install a Support Platform in the Cabinet.......................... 6
Electrical Power Supply Requirements............................. 6
Installation Instructions..................................................... 7
Remove the Drawer ......................................................... 7
Installing the Chassis........................................................ 7
Re-installing the Drawer.................................................... 8
Verifying the Warming Drawer Operation......................... 8
Installation Checklist......................................................... 8
Before You Begin...
Important:
Installer: In the interest of safety and to minimize problems, read these installation instructions completely and carefully
before you begin the installation process. Leave these installation instructions with the customer.
Customer: Keep these installation instructions for future reference and the local electrical inspector’s use.
If you have questions or problems with installation, contact
your Dacor dealer or the Dacor Customer Service Team.
For repairs to Dacor appliances under warranty call the
Dacor Distinctive Service line. Whenever you call, have
the complete model and serial number for your appliance
available. The numbers are found on the product data label
located on back of the drawer front.
The data label also contains the product electrical
requirements
Dacor Customer Service
Phone: (800) 793-0093 (U.S.A. and Canada)
Monday — Friday 6:00 a.m. to 5:00 p.m. Pacific Time
Web site:
www.Dacor.com
Dacor Distinctive Service (repairs under warranty only)
Phone: (877) 337-3226 (U.S.A. and Canada)
Monday — Friday 6:00 a.m. to 4:00 p.m. Pacific Time
Product data label
on back for drawer
front
Important Safety Instructions
Important Information About
Safety Instructions
•
•
The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or
operating this or any other appliance.
Always contact the Dacor Customer Service Team
about problems and conditions that you don’t
understand.
Safety Symbols and Labels
DANGER
Immediate hazards that WILL result in severe personal
injury or death.
warning
Hazards or unsafe practices that COULD result in severe
personal injury or death.
caution
Hazards or unsafe practices that COULD result in minor
personal injury or property damage.
1
Important Safety Instructions
General Safety Precautions
To reduce risk of fire, electric shock, serious injury or death when using your appliance, follow basic precautions, including
the following:
warning
warning
•
•
Use this appliance only for its intended use as
described in this manual. Use it only to warm food
and heat plates and utensils. It is not designed for
commercial, industrial or laboratory use.
Only model OWD24 is approved for use in outdoor
installations and near water (bathrooms). Do not
use, store or install warming drawer models other
than OWD24 near water, for example, near sinks,
swimming pools or in a wet basement.
•
Model OWD24, when installed as a towel warmer,
must have the supplied wire rack installed in the
drawer bottom according to these instructions.
•
Do not install or operate a product that is
damaged, has a damaged power cord or plug,
or is malfunctioning in any manner. Return the
appliance to the nearest authorized service facility
for examination, repair or adjustment.
•
Make sure that the appliance has been properly
installed and grounded by a qualified installer
according to the accompanying installation
instructions. Have the installer show you the
location of the electrical outlet so that you know
where to disconnect power to the appliance.
•
Do not repair or replace any part of the warming
drawer unless specifically recommended in the
literature accompanying it. All other service should
be done by a qualified technician.
•
Use of accessory attachments not recommended by
the appliance manufacturer may cause injuries.
•
Before cleaning or performing any type of service,
make sure that the power plug is disconnected from
the electrical outlet and that the unit is cool.
•
•
DO NOT TOUCH ANY HOT SURFACES IN OR
ON THE WARMING DRAWER DURING OR
IMMEDIATELY AFTER USE. Use the handle
instead. After use, make sure these surfaces have
had sufficient time to cool before touching them.
Heating elements may be hot, even though they are
dark in color.
To avoid the possibility of fire or burns, do not allow
clothing, potholders, towels or rags to come into
contact with any part of the warming drawer during
and immediately after use. Do not wear loose or
hanging apparel while using the appliance.
•
Clean the warming drawer thoroughly before
operating it for the first time.
•
To reduce the risk of fire in the warming drawer, do
not overcook food. Do not leave it unattended with
paper, plastic or other combustible materials inside.
•
If materials inside the warming drawer should ignite,
keep the drawer closed and shut off the power at
the circuit breaker panel or fuse box.
•
Exercise caution when opening the warming drawer.
Let hot air or steam escape before looking or
reaching into the warming drawer.
•
Use only dry pot holders when removing food and
cookware from the warming drawer. Wet pot holders
can cause steam burns.
•
Do not put items like whole eggs, sealed containers
or closed glass jars in the drawer. They may
explode when heated, causing injury.
•
When the warming drawer is on in continuous
mode (∞), it will remain on until turned off manually.
Exercise caution when operating the unit in
continuous mode.
•
Do not place more than 50 pounds in the drawer.
•
Properly clean and maintain the unit regularly as
instructed in the use and care manual. Clean only
those parts listed, in the manner specified.
•
Do not use abrasive scrubbers or abrasive/caustic
cleaners or detergents on this appliance. They
may permanently damage the finishes. Do not use
aerosol cleaners, because they may be flammable
or cause corrosion of metal parts.
•
Make sure the warming drawer is used only by
those individuals who are able to operate it properly.
•
Do not tamper with the controls.
•
Never allow anyone, including children to sit, stand
or climb on any part of the appliance, including
the drawer. Doing so may cause tipping, damage,
serious injury or death.
•
Do not leave children unattended in the area around
the appliance. Do not allow children to operate it,
play with the controls, pull on the handle or touch
other parts. Do not store items of interest to children
above the warming drawer. Children could be
burned or injured while climbing on the appliance.
Read and save these instructions
2
Installation Specifications
Verifying the Package Contents
•
Use and care manual
•
Mounting screws
•
Wire rack with mounting hardware (OWD24 only)
C
B
Installation Planning
E
•
A qualified technician must complete the installation of this builtin appliance. Proper installation is the customer's responsibility.
•
Carefully check the location where the drawer is to be installed.
The drawer should be placed for convenient access. Make
certain that electrical power can be provided in the selected
location. Install the warming drawer in wood cabinets only.
•
Plan the installation so that all minimum clearances are met or
exceeded. Dimensions shown provide minimum clearances,
unless otherwise noted. Be certain that proper clearance is
provided for the drawer door when it is in the open position.
•
The specified minimum cabinet depth and width must be
provided. The cabinet depth and width must completely enclose
the recessed portion of the drawer.
•
Cabinet cutout dimensions must be used as indicated. All
contact surfaces between the appliance and the cabinet must
be solid and level. The drawer support platform must be flush
with the bottom edge of the cabinet cutout.
•
Chassis
5/16”
(8 mm)
Drawer open
Overall Dimensions - IWD/OWD Series
Top View
Make certain that you have everything necessary to ensure a
proper installation before proceeding.
•
A custom front panel is required for IWD
series models and optional for OWD24.
•
An optional Epicure® style front panel kit is
available for model OWD24.
**
F
40" (1016 mm)
3 prong
120 Vac power cord
Mounting hole,
9 places
**
**
**
G
D
Chassis without
drawer installed
A
** = OWD24 mounting holes
Drawer Face Dimensions
(IWD/OWD Series)
Warming
Drawer
Model No.
(A) Dimension
Drawer Face
Width
Chassis Dimensions
(IWD/OWD Series)
(B) Dimension
Chassis Width
(C) Dimension
Chassis Face
Width
IWD24
22 5/16” (567 mm) 22 1/4” (565 mm)
22 3/8” (568 mm)
IWD27
25 5/16” (643 mm) 25 1/4” (641 mm)
25 3/8” (645 mm)
IWD30
28 5/16” (719 mm) 28 1/4” (718 mm)
28 3/8” (721 mm)
OWD24
22 1/2” (571 mm)
22 1/2” (571 mm)
22 1/2” (571 mm)
(D)
(E)
(F)
(G)
Dimension Dimension Dimension Dimension
Drawer
Chassis
Drawer
Chassis
Face Height
Depth
Depth
Height
8 15/16”
(227 mm)
23 3/8”
(594 mm)
23 13/16”
(605 mm)
9 1/16”
(230 mm)
11 7/8”
(302 mm)
20”
(508 mm)
18”
(457 mm)
11 7/8”
(302 mm)
See following page for chassis dimensions for other models
3
Installation Specifications
10 1/8"
(257 mm)
A
Drawer Face Dimensions
(MWDH series shown)
Model
(A) Drawer Face
Width
(B) Chassis Face
Width
(C) Chassis Width
ERWD30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
EWD24
24” (610 mm)
23 5/8” (600 mm)
22 1/4” (565 mm)
EWD27
27” (686 mm)
26 5/8” (676 mm)
25 1/4” (641 mm)
EWD30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
EWD36
36” (914 mm)
35 5/8” (905 mm)
34 1/4” (870 mm)
MRWD27
27” (686 mm)
26 5/8” (676 mm)
25 1/4” (641 mm)
MRWD30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
MWDH27
27” (686 mm)
26 5/8” (676 mm)
25 1/4” (641 mm)
MWDH30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
MWDV27
27” (686 mm)
26 5/8” (676 mm)
25 1/4” (641 mm)
MWDV30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
PWD27
27” (686 mm)
26 5/8” (676 mm)
25 1/4” (641 mm)
PWD30
30” (762 mm)
29 5/8” (752 mm)
28 1/4” (718 mm)
Warming Drawer Overall Dimensions
See page 3 for IWD and OWD series chassis dimensions
ERWD
3 1/2"
(89 mm)
B
1 1/8"
(29 mm)
C
1"
(25 mm)
23 3/8"
(594 mm)
MRWD30B
(only)
1 7/16"
(37 mm)
1"
(25mm)
All other
MRWD series
Chassis
EWD
3 7/16"
(87 mm)
MWDH/V
3 1/4"
(83 mm)
PWD
2 1/4"
(57 mm)
1"
(25 mm)
1"
(25 mm)
Handle Dimensions
Mounting
Hole 9 Places
5/64"
(2mm)
Drawer open
23 13/16
(605 mm)
1/2"
(13 mm)
10"
(254 mm)
Chassis without
drawer inserted
Overall Dimensions
Top View
(EWD series shown)
1/2"
(13 mm)
Chassis Dimensions
4
40" (1016 mm)
3 prong
120 Vac power cord
9"
(229 mm)
Installation Specifications
Warming drawer
36" Typ.
(914 mm)
Warming drawer
C
27"/30"/36"
Dacor
single oven
3/4" Min.*
(19 mm)
D
D
120 Vac
electrical
outlet
Warming drawer 120 Vac
elect.
C
D
3/4" Min.*
(19 mm)
A
B
Warming drawer 120 Vac
elect.
1 1/2" (38 mm)
Typical countertop
Cooktop
Warming drawer
C
C
Toe kick
3/4" Min.*
(19 mm)
A
3/4” Min.*
(19 mm)
C
Cutouts Dimensions
NOTES:
36" Typ.
(914 mm)
A
B
120 Vac
electrical
outlet
•
Models EWD36, OWD24 and IWD series
models cannot be installed above or
below another warming drawer (any type).
•
Model OWD24 is not approved for
installation above, below or adjacent to a
wall oven or a warming drawer, including
the same model.
Model
(A) Cutout Width
(B) Min. Width to
Adjacent Doors/
Drawers
(C) Cutout Height
(D) Min. Vertical Gap
Between Cutouts
ERWD30
28 1/2” (724 mm)
30 1/4” (768 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
EWD24
22 1/2” (572 mm)
24 1/4” (616 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
EWD27
25 1/2” (648 mm)
27 1/4” (692 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
EWD30
28 1/2” (724 mm)
30 1/4” (768 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
EWD36
34 1/2” (876 mm)
36 1/4” (921 mm)*
9 1/8” (232 mm)
NA
IWD24
22 1/2” (572 mm)
**
9 1/8” (232 mm)
NA
IWD27
25 1/2” (648 mm)
**
9 1/8” (232 mm)
NA
IWD30
28 1/2” (724 mm)
**
9 1/8” (232 mm)
NA
MRWD27
25 1/2” (648 mm)
27 1/4” (692 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
MRWD30
28 1/2” (724 mm)
30 1/4” (768 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
MWDH27
25 1/2” (648 mm)
27 1/4” (692 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
MWDH30
28 1/2” (724 mm)
30 1/4” (768 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
MWDV27
25 1/2” (648 mm)
27 1/4” (692 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
MWDV30
28 1/2” (724 mm)
30 1/4” (768 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
OWD24
22 5/8” (575 mm) 24 1/4” (616 mm)*** 11 15/16” (303 mm)
PWD27
25 1/2” (648 mm)
27 1/4” (692 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
PWD30
28 1/2” (724 mm)
30 1/4” (768 mm)*
9 1/8” (232 mm)
1 1/4” (32 mm)*
NA
Min. Cutout
Depth
24” (610 mm)
20 1/8” (511 mm)
24” (610 mm)
* Bare minimum spacing to allow for ventilation and avoid scraping on EWD, MW and PWD series models.
** On IWD series models or OWD24 without the optional front panel kit: The chassis and the drawer faceplate are smaller
than the cutout. The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel
must exceed the appropriate cutout dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space
on the top, bottom and sides from the custom front panel edge to prevent scraping against adjacent doors, drawers and
the countertop.
*** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and
below cutout is 3/4” minimum. See ** above for OWD24 with custom front panel.
5
Installation Specifications
Install a Support Platform in the
Cabinet
Chassis
face
Provide a platform (100 lb. load capacity) within the cabinet
upon which the warming drawer will be supported. The
platform must be installed level and straight. The top edge
of the platform must be flush with the cutout at the front of
the cabinet. There are no provisions to level the warming
drawer after it has been installed. 3/4” (19 mm) thick
plywood is recommended.
Support
platform
NOTE: If the drawer is not installed in a level fashion, the
drawer may slide open on its own or may not seal tightly,
allowing heat to escape and resulting in poor warming
drawer performance.
Electrical Power Supply
Requirements
warning
IMPORTANT: This appliance is equipped with a three
prong grounding electric plug for protection against
possible electric shock hazards. It must be plugged into
a dedicated, grounded, electrical outlet. If only a two
prong electrical outlet is available, it is the responsibility
of the customer to have it replaced with a dedicated,
properly grounded three prong electrical outlet. To
avoid an electric shock hazard, do not under any
circumstances:
•
Cut or remove the third (ground) prong from the
power cord.
•
Use an adapter plug.
•
Use a power cord that is frayed or damaged.
•
Immerse the power cord or plug in water or other
liquid.
•
Connect the appliance to an extension cord.
NOTE: Use of a ground fault interrupter (GFI) is not
recommended.
Three prong
Three prong plug grounded outlet
6
•
The correct voltage, frequency and amperage must be
supplied to the electrical outlet from a grounded, single
phase circuit that is protected by a properly sized circuit
breaker or time-delay fuse.
•
The required voltage, frequency and amperage ratings
are listed on the product data label. See page 1 for
location.
Nominal Electrical Supply Requirements
120 Vac, 60 Hz, 15 Amp., dedicated circuit
The warming drawer is supplied with a 40” (1016 mm)
power cord with a three prong grounded plug.
Total Connected Load
0.5 kW (4 Amp.)
•
The power supply requirements shown above are for
reference only. If they do not agree with those listed
on the product data label, use the requirements on the
product data label.
•
It is the owner’s responsibility to ensure that the
electrical outlet is installed by a qualified electrician.
The electrical installation must comply with the latest
revision of the National Electric Code ANSI/NFPA 70
and local codes and ordinances.
•
If the electrical service provided does not meet the
product specification, or does not conform to the NEC
or local standards, do not proceed with the installation.
Call a licensed electrician to correct the electrical
service before proceeding.
•
Be certain to locate the electrical outlet in an
accessible location, so that the warming drawer may
be easily unplugged in the event that service becomes
necessary.
•
Keep the electrical cord away from hot surfaces.
Installation Instructions
warning
•
o avoid personal injury caused by the appliance
T
falling forward when the drawer is opened, secure
the chassis to the cabinet and support platform as
instructed.
•
Be certain that the power plug is disconnected from
the electrical outlet before installation.
•
Verify that the electrical supply matches the ratings
found on the appliance data plate and the installation
specifications before proceeding.
Remove the Drawer
emove the drawer from the appliance to allow access
R
to the mounting holes during installation, and to reduce
weight:
1. Pull the drawer out to the fully open position.
2. Push in on the locking tab on one side as you pull the
drawer up.
Installing the Chassis
1. Grasp the warming drawer chassis on opposite
sides and slide it partially into the cabinet opening.
Temporarily support the chassis in place so that it will
not tilt or fall.
2. From an adjoining cabinet, reach in behind the drawer
and pull the power cord until the plug is next to the
electrical outlet. Do not plug in the power cord at this
time.
3. After positioning the power cord and plug, slide the
chassis completely into the cabinet until the front frame
is positioned flush against the cabinet face.
4. Use the screws provided to secure the warming drawer
chassis to the cabinet and support platform, insert them
into the mounting holes and tighten into place. You may
want to drill pilot holes prior to installing the mounting
screws.
Mounting hole, 9 places
3. When the drawer comes loose from the slide, repeat
the same process on the opposite side.
4. Grip the drawer on both sides and pull it free.
5. For safety, push both drawer slides into the drawer
opening.
STEP 2: Push
locking tab
Mounting Hole Locations - ERWD, EWD, IWD, MRWD,
MWDH, MWDV and PWD Series Models
(IWD series models do not have a flange around
the edge of the faceplate)
Mounting hole, 4 places
STEP 3: Pull up on
front of drawer
Mounting Hole Locations OWD24
Continued...
Style varies, EWD 27 shown
7
Installation Instructions
Re-installing the Drawer
Towel Rack Installation
1. Pull the drawer slides all the way out of the drawer
opening.
(OWD24 Only)
2. Gently lower the drawer between the extended slides
until it is suspended by them.
3. Slide the back of the drawer mounting brackets under
the drawer mounting clips on the slides.
Model OWD24 is designed so that it can be used as a
towel warmer if desired. Other models are not equipped for
this application. To use model OWD24 as a towel warmer,
you must install the towel rack included with the unit in the
bottom of the drawer.
4. Push one side of the drawer down onto its locking tab,
until the tab locks into place.
To install the towel rack:
5. Repeat the same process on the opposite side.
2. Insert the towel rack into the drawer in the orientation
shown below.
6. Gently open and close the drawer to make sure that it
is properly installed.
1. Open the drawer completely.
STEP 3: Slide mounting
bracket under clip on slide
Clip on slide
Slide
STEP 4: Push front
of drawer down until
tabs lock into place
8
3. Use the clip and screw included with the rack to attach
it to the back of the drawer face as shown below. There
is a hole for the screw in the back of the face plate
near the bottom.
Installation Instructions
Warming Drawer Control Panel Layout
Verify Warming Drawer
Operation
1. Connect power plug to the electrical outlet.
2. Open the drawer and press the ON/OFF key on the
control panel.
3. Press the PROOF, LOW, MED and HIGH keys each
in turn. When you press each key, the indicator directly
above it should light. Leave the control panel set to
HIGH.
Installation Checklist
warning
•
To ensure a safe and proper installation, the
following checklist should be completed by the
installer to ensure that no part of the installation has
been overlooked.
•
Proper installation is the responsibility of the
homeowner. The importance of proper installation of
your warming drawer cannot be overemphasized.
4. Press the SELECT key. The 1 HOUR indicator should
light. Press and release the SELECT key three (3)
more times. Each time you press the SELECT key, the
2 HOUR, 3 HOUR and 4 HOUR indicator lights should
come on. All lights should be on after pressing the
SELECT key the third time.
□□
Mounting platform been installed according to the
instructions on page 6.
□□
Properly grounded, dedicated, three prong electrical
outlet been has been installed for the appliance by a
licensed electrician. See page 6.
5. Press the "∞" key. The indicator light above it
should come on and the 1, 2 ,3 and 4 HOUR
lights should go out.
□□
6. The warming drawer should begin to heat.
You should begin to feel the inside of the
drawer begin to heat within five (5) to ten (10)
minutes.
The chassis has been properly fastened to the
mounting platform and sides of the cabinet.
See page 7.
□□
□□
The drawer has been properly installed. See page 8.
7. When you have determined that the heating
element is working, press the ON/OFF key.
□□
□□
Proper operation has been verified?
□□
Save these instructions for future reference.
If the warming drawer does not operate properly, follow
these troubleshooting steps:
•
Verify that the circuit breaker for the electrical outlet
is on and not tripped. Make sure the power plug is
connected.
•
Repeat the above tests.
•
If the appliance still does not work, contact Dacor
Distinctive Service at (877) 337-3226. Do not attempt
to repair the appliance yourself. Be sure to have the
model and serial numbers available when you call. See
page 1 for model/serial number location.
Model OWD24 for use as towel warmer: The towel rack
has been installed. See page 8.
The warranty has been activated on-line or the
warranty card filled out completely and mailed?
Dacor is not responsible for the cost of correcting problems
caused by a faulty installation.
9
Dacor ● Phone: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.com
Warming Drawer
Use and Care Manual
Models: ERWD30, EWD24, EWD27, EWD30, EWD36,
IWD24, IWD27, IWD30, MRWD27, MRWD30,
MWDH27, MWDH30, MWDV27, MWDV30,
OWD24, PWD27, PWD30
Style varies, model EWD27 shown
Ta b l e o f C o n t e n t s
Important Safety Instructions................................. 1
Getting to Know Your Warming Drawer..................... 3
Operating Instructions............................................ 4
Care and Cleaning................................................. 6
Before You Call for Service...................................... 7
Warranty and Service............................................. 8
Warranty Card.........................................Back Cover
Part No. 102344 Rev. J
© 2007 Dacor, all rights reserved
Important Safety Instructions
Installer: Leave these instructions with the
appliance.
danger
Customer: Read this use and care manual completely
before using your warming drawer. Save it for future
reference. It contains important use and care information. Keep your sales receipt or canceled check
in a safe place. Proof of original purchase date is
required for warranty service.
IMPORTANT: To avoid the possibility of explosion or
fire, do not store or use flammable or explosive vapors
and liquids (such as gasoline) inside or in the vicinity
of this or any other appliance. Keep items that could
explode, such as aerosol cans away from the appliance.
Do not store flammable or explosive materials in
adjacent cabinets or areas.
For service and warranty information see page 8.
If you have any questions (other than warranty questions), call:
warning
Dacor Customer Service
NEVER use this appliance as a space heater to heat or
warm the room.
(800) 793-0093 (U.S.A. and Canada)
Monday — Friday 6:00 a.m. to 5:00 p.m. Pacific Time
Web site: www.Dacor.com
warning
When you call, have the complete model and serial
number for your appliance available. The numbers are
found on the product data label located on back of the
drawer front. See page 3 for label location. Write these
numbers below for future reference.
Do not use water on grease fires – smother fire or flame
or use dry chemical or foam-type extinguisher.
WARNING
Model Number __________________________________
IMPORTANT: This appliance is equipped with a three
prong grounding electric plug for protection against
possible electric shock hazards. It must be plugged into
a dedicated, grounded, electrical outlet. If only a two
prong electrical outlet is available, it is the responsibility
of the customer to have it replaced with a dedicated,
properly grounded three prong electrical outlet. To
avoid an electric shock hazard, do not under any
circumstances:
Serial Number __________________________________
Date of Purchase ________________________________
Since Dacor continuously improves the quality and performance of our products, we may need to make changes to
the appliance without updating this manual.
Important Information About
Safety Instructions
The Important Safety Instructions and warnings in
this manual can not cover all possible problems and conditions that can occur. Use common sense and caution when
installing, maintaining or operating this appliance.
Safety Symbols and Labels
•
Cut or remove the third (ground) prong from the
power cord.
•
Use an adapter plug.
•
Use a power cord that is frayed or damaged.
•
Immerse the power cord or plug in water or other
liquid.
•
Connect the appliance to an extension cord.
NOTE: Use of a ground fault interrupter (GFI) is not
recommended.
danger
Immediate hazards that WILL result in severe personal
injury or death.
warning
Hazards or unsafe actions that COULD result in severe
personal injury or death.
caution
Power supply cord Grounded type electrical
with three-prong outlet (ground fault circuit
grounding plug
not recommended)
Hazards or unsafe actions that COULD result in minor
personal injury or property damage.
1
Important Safety Instructions
General Safety Precautions
To reduce risk of fire, electric shock, serious injury or death when using this appliance, follow basic precautions, including the following:
warning
•
Read this manual completely before operating this
appliance.
•
Use this appliance only for its intended use as
described in this manual. Use it only to warm food
and heat plates and utensils. It is not designed for
commercial, industrial or laboratory use.
•
Only model OWD24 is approved for use in outdoor
installations and near water (bathrooms). Do not
use, store or install warming drawer models other
than OWD24 near water, for example, near sinks,
swimming pools or in a wet basement.
•
Model OWD24, when installed as a towel warmer,
must have the supplied wire rack installed in the
drawer bottom. Secure the rack with the screw and
clip supplied. See the installation instructions.
•
Do not install or operate a product that is
damaged, has a damaged power cord or plug, or is
malfunctioning in any manner. Return the appliance
to the nearest authorized service facility for
examination, repair or adjustment.
•
•
•
•
Make sure that this appliance has been properly
installed and grounded by a qualified installer
according to the accompanying installation
instructions. Have the installer show you the
location of the electrical outlet so that you know
where to disconnect power to the appliance.
Do not repair or replace any part of the warming
drawer unless specifically recommended in the
literature accompanying it. All other service should
be done by a qualified technician.
Use of accessory attachments not recommended by
the appliance manufacturer may cause injuries.
Before cleaning or performing any type of service,
make sure that the power plug is disconnected from
the electrical outlet and that the unit is cool.
•
Keep the electrical cord away from heated surfaces.
•
DO NOT TOUCH ANY HOT SURFACES IN OR ON
THE WARMING DRAWER DURING OR IMMEDIATELY
AFTER USE. Use the handle instead. After use,
make sure these surfaces have had sufficient time
to cool before touching them. Heating elements may
be hot, even though they are dark in color.
•
warning
To reduce the risk of fire in the warming drawer, do
not overcook food. Do not leave it unattended with
paper, plastic or other combustible materials inside.
2
•
To avoid the possibility of fire or burns, do not allow
clothing, pot holders, towels or rags to come into
contact with any part of the warming drawer during
and immediately after use. Do not wear loose or
hanging apparel while using this appliance.
•
If materials inside the warming drawer should
ignite, keep the drawer closed and shut off the
power at the circuit breaker panel or fuse box.
•
Exercise caution when opening the drawer. Let hot
air or steam escape before looking or reaching into
the warming drawer.
•
Use only dry pot holders when removing food and
cookware from the warming drawer. Wet pot holders
can cause steam burns.
•
Do not put items like whole eggs, sealed containers
or closed glass jars in the warming drawer. They
may explode when heated, causing injury.
•
Do not place more than 50 pounds in the drawer.
•
Properly clean and maintain the unit regularly as
instructed in this manual. Clean only those parts
listed in this manual, in the manner specified.
•
Do not use abrasive scrubbers or abrasive/caustic
cleaners or detergents on this appliance. They
may permanently damage the finishes. Do not use
aerosol cleaners, because they may be flammable or
cause corrosion of metal parts.
•
Clean the appliance thoroughly before operating it
for the first time.
•
Make sure the warming drawer is used only by
those individuals who are able to operate it properly.
•
Do not tamper with the controls.
•
Preheat the warming drawer before use.
•
Never allow anyone, including children to sit, stand
or climb on any part of the appliance, including
the drawer. Doing so may cause tipping, damage,
serious injury or death.
•
Do not leave children alone or unattended in the
area around the appliance. Do not allow children to
operate it, play with the controls, pull on the handle
or touch other parts.
•
Do not store items of interest to children above the
warming drawer. Children could be burned or injured
while climbing on the appliance.
•
Save this manual for future use.
Getting to Know Your Warming Drawer
Gasket
Drawer
Control panel
Product data label on back of
drawer front
Drawer slide
Drawer front:
Style and size varies with model
Drawer capacity: 50 pounds
Drawer dimensions:
Back of Drawer Front
Model IWD24: 5”H x 20”W x 22¾”D
Model OWD24:
6½”H x 20¼”W x 17 7/8”D
27” models: 5”H x 23”W x 22¾”D
Humidity vents
30” models: 5”H x 26”W x 22¾”D
36” models: 5”H x 32”W x 22¾”D
Humidity vents
Humidity control
Models IWD24, IWD27, IWD30 and OWD24 are
not equipped with the humidity control or vents
3
Operating Instructions
Operation
warning
•
When the warming drawer is on in continuous mode
(∞), it will remain on until turned off manually. To
avoid a fire hazard or burns, exercise caution when
operating the unit in continuous mode.
•
Do not block the humidity vents on the back of the
drawer front and along the left and right sides of the
drawer. Excessive heat buildup can occur.
•
The warming drawer is equipped with four temperature
settings and a timer that can be set for one, two, three
or four hours. The warming drawer can also be set for
continuous operation. See the table on the facing page for
suggested settings for different foods.
To turn the unit on:
1. Select the humidity level. Slide the lever located on
the back of the drawer face to the desired position.
To increase humidity inside the drawer, slide the lever
closer to the MOIST symbol. To decrease humidity
inside the drawer, slide the lever closer to the CRISP
symbol. The lever can also be positioned anywhere
between the MOIST and CRISP settings.
Food safety is an important consideration when
using a warming drawer. In the PROOF and LOW
temperature settings, bacteria growth may occur.
Use the MED and HIGH settings if holding certain
foods for more than two to three hours.
Things to Know Before You Start
2. Push the ON/OFF key.
3. Push the key for the desired temperature setting.
Preheating
• For best results, preheat your warming drawer for
about 20 minutes before use. If you put hot food into
a cool, confined area, any steam that is present will
condense. If you preheat your warming drawer, there
will be less chance of water due to condensation.
Preheat times vary depending on the temperature setting.
Setting
Temperature*
PROOF
100 °F (38 °C)
LOW
140 °F (60 °C)
MED
175 °F (80 °C)
HIGH
200 °F (93 °C)
* Temperatures are approximate
Humidity Control
4. Select the amount of time you want
the warming drawer to be on: Push the
SELECT key until the desired number
of hours lights up on the control panel.
• The warming drawer has two distinct humidity modes.
The “MOIST” setting seals the food’s moisture in the
warming chamber, maintaining the water content of
the food. The “CRISP” setting allows the moisture to
vent out of the sides of the warming drawer, retaining the crispness of other food types. The MOIST •
CRISP lever opens and closes vents located on the
inside of the drawer front.
or
Push the continuous key (∞) to keep
the unit on constantly. Push the ON/
OFF key to turn the warming drawer
off, when done.
• Do not block the humidity vents any time you operate
your warming drawer.
Back of drawer front
Warming Serving Containers
Lever
• To warm plates, and other serving containers:
• Place them carefully into the warming drawer and set
the temperature to PROOF or LOW, depending upon
your personal preference. Do not drag plates across
the drawer. They may scratch the drawer surface.
• Before using any delicate dinnerware in the warming drawer, determine its maximum recommended
usage temperature from the plate manufacturer. It is
not necessary to preheat the warming drawer when
warming serving dishes.
Vents
Models IWD24, IWD27,
IWD30 and OWD24 do
not have this feature
MOIST
• You can also use plastic wrapping on plates to keep
foods hot and moist.
CRISP
4
Operating Instructions
Control Panel
Temperature and Humidity Control Setting Guidelines
FOOD ITEMS
TEMPERATURE
SETTINGS
MOIST-CRISP
SELECTION
COVERED/
UNCOVERED
Bacon
HIGH
Crisp
Uncovered
Beef - rare
LOW
Moist
Covered
Bread - hard rolls
LOW
Crisp
Uncovered
Bread - proofing
PROOF
Moist
Damp towel
Casseroles
LOW
Moist
Uncovered
Coffee cake
LOW
Moist
Uncovered
Cooked cereals
LOW
Moist
Uncovered
Dinner
MED
Moist
Uncovered
Eggs
LOW
Moist
Covered
Enchiladas
LOW-MED
Moist
Uncovered
Fish/seafood
LOW
Moist
Covered
Fried food
HIGH
Crisp
Uncovered
Gravy, cream sauces
LOW
Moist
Covered
Ham
LOW
Moist
Covered
Hors D’ oeuvres
LOW-MED
Crisp
Uncovered
Lamb
LOW
Moist
Uncovered
Pancakes
LOW-MED
Moist
Covered
Pies - single crust
LOW
Moist
Uncovered
Pizza
LOW-MED
Moist
Covered
Potatoes - baked
HIGH
Crisp
Uncovered
Poultry
HIGH
Moist
Uncovered
Vegetables
LOW
Moist
Covered
Waffles - crisp
HIGH
Moist
Uncovered
5
Care and Cleaning
Painted Surfaces
caution
•
To prevent permanent damage to the appliance
surfaces, do not use abrasive cleaners or scrubbers.
•
Do not allow acids (citrus juices, tomato sauces,
etc.) to remain on the warming drawer’s surfaces.
The finish may stain.
•
Do not try to remove heavy spills with a sharp object
such as a knife or metal spatula. Sharp objects may
scratch the surfaces.
•
Always wipe stainless steel surfaces in the direction
of the grain.
For the front face of warming drawers with a painted
finish, clean with a solution of mild detergent and hot
water. Rinse and dry with a soft cloth. Do not use abrasive
cleaners or scrubbers. They may permanently damage the
finish.
Gasket
The gasket is located around the edge of the drawer
opening, below the control panel.
Gently clean the gasket with a solution of mild detergent
and hot water. Rinse and dry with a soft cloth. The gasket
material is soft, so be careful not to crush or damage
it. Damaging the gasket will cause a poor heat seal and
result in poor warming drawer performance.
Control Panel
Clean the control panel with a soft cloth soaked with a
solution of mild detergent and hot water. Rinse and dry
with a soft cloth. Exercise caution to avoid introduction of
liquids into the area behind the control panel. Do not use
abrasive cleaners or scrubbers. They may permanently
damage the finish or scrap off the letters and graphics.
Drawer Slides
The warming drawer has slides positioned on each side
of the drawer. They allow the drawer to slide in and out
smoothly. Remove the drawer from the slides to make
cleaning easy or to access the serial number plate. The
drawer slides themselves do not require maintenance.
Moist • Crisp Control
Clean the Moist • Crisp lever with a solution of mild detergent and hot water. Rinse and dry with a soft cloth.
Removing the Drawer from the
Appliance
Drawer Handle
Allow the drawer to cool before attempting to remove it.
Clean the drawer handle with a solution of mild detergent
and hot water. Rinse and dry with a soft cloth.
1. Pull the drawer out to the fully open position.
2. Push in on the locking tab on one side as you pull the
drawer up. See the facing page.
You may also use Dacor Stainless Steel Cleaner. It is
available from your Dacor dealer. Use it according to the
directions on the package.
3. When the drawer comes loose from the slide, repeat
the same process on the opposite side.
Always wipe stainless steel surfaces in the direction of the
grain.
4. Grip the drawer on both sides and pull it free.
Glass Surfaces
5. For safety, push both drawer slides into the drawer
opening.
Clean all glass surfaces with a solution of mild detergent
and hot water. You may also use a mild glass cleaner to
remove fingerprints or smears. Dry completely with a soft,
lint-free cloth.
Reinstalling The Drawer
Brass and Chrome Surfaces
2. Gently lower the drawer between the extended slides
until it is suspended by them.
1. Pull the drawer slides all the way out of the drawer
opening.
Clean brass and chrome surfaces with a solution of mild
detergent and warm water. Rinse, dry and polish with a
soft, lint-free cloth.
3. Slide the back of the drawer mounting brackets under
the clips on the slides. See the facing page.
4. Push one side of the drawer down onto its locking tab,
until the tab locks into place.
You may also use Dacor Stainless Steel Cleaner. It is
available from your Dacor dealer. Use it according to the
directions on the package.
5. Repeat the same process on the opposite side.
6. Gently open and close the drawer to make sure that it
is properly installed.
6
Care and Cleaning
Slide mounting bracket
under clip on slide
Push in on tab
Clip on slide
Slide
Pull up on
drawer front
Push drawer front
down until tab locks
in place
Drawer Installation
Drawer Removal
Before You Call for Service
Problem Solution Guide
problem
Nothing works
may be caused by
Power plug disconnected
Connect plug to a dedicated, grounded, threeprong electrical outlet
Timer is not set
Select time duration according to the
Operating Instructions section
Warming drawer is not connected
to power
Plug the warming drawer into a 120 Vac,
15 Amp., dedicated electrical outlet
Tripped circuit breaker or blown
fuse
Check the house circuit breaker or fuse for
the circuit that supplies power to the warming
drawer
Drawer does not slide smoothly Drawer is incorrectly mounted into
or drags
slide mechanism
Excessive condensation.
One or more of the indicator
lights on the control panel blink
on and off (one second on, one
second off)
what to DO
Remount drawer into slide, per instructions
above
Drawer is over-loaded or the load
is unbalanced
Reduce the weight to less than 50 pounds.
Redistribute drawer contents
Warming drawer not preheated
Preheat the warming drawer before each use
Incorrect humidity control setting
Set humidity control to CRISP to allow moisture to vent
The control panel computer has
detected an error:
#1 - Temperature error
#2 - Sensor error
#3 - Key pad error
#4 - Control error
Try resetting the computer. Disconnect the
power cord, wait 20 seconds, then reconnect
it. Check the control panel. If the indicator
light still flashes, call for service. See page 8
7
Warranty and Service
If You Need Service...
OUTSIDE THE FIFTY STATES OF THE U.S.A., THE
DISTRICT OF COLUMBIA, AND CANADA:
Before you request service, please review the Before
You Call for Service section of this manual on page 7. If
you have performed the checks in the Problem Solution
Guide and the problem has not been remedied, please
contact us at one of the numbers below. Prior to requesting service, it is helpful to be familiar with the terms and
conditions in the Warranty section on this page.
LIMITED FIRST YEAR WARRANTY
For warranty repairs, call:
If your DACOR product fails to function within one year of
the original date of purchase, due to a defect in material
or workmanship, DACOR will furnish a new part, F.O.B.
factory, to replace the defective part. All delivery, installation, and labor costs are the responsibility of the purchaser. The owner must provide proof of purchase, upon
request, and have the appliance accessible for service.
Dacor Distinctive Service
What Is Not Covered
Phone: (877) 337-3226 (U.S.A. and Canada)
Monday — Friday 6:00 a.m. - 4:00 p.m. Pacific Time
• Service calls to educate the customer in the proper
use and care of the product.
For a list of Dacor service agents for non-warranty
repairs:
Dacor Customer Service
• Failure of the product when used for commercial,
business, rental or any application other than for residential consumer use.
Phone: (800) 793-0093
Business Hours: 6:00 a.m. - 5:00 p.m. Pacific Time
• Replacement of house fuses or fuse boxes, or resetting of circuit breakers.
Contact us through our web site at:
• Breakage, discoloration or damage to glass, metal
surfaces, plastic components, trim, paint or other
cosmetic finish, caused by improper usage or care,
abuse, or neglect.
www.Dacor.com
At Dacor, we believe that our quality of service equals
that of our product. Should your experience with our service network or product be different, please contact our
Customer Service Team and share your encounter with
us. We will do our utmost to resolve the situation for you
and deliver on our Dacor promise.
• Damage due to installation or operation in damp or
wet environments (except for models specified for
such use).
• Damage to the product caused by accident, fire, flood
or other acts of God.
If you need anything clarified, just let us know.
FULL ONE-YEAR WARRANTY
THE REMEDIES PROVIDED FOR IN THE ABOVE EXPRESS WARRANTIES ARE THE SOLE AND EXCLUSIVE REMEDIES. THEREFORE, NO OTHER EXPRESS WARRANTIES ARE MADE, AND
OUTSIDE THE FIFTY STATES OF THE UNITED STATES, THE DISTRICT OF COLUMBIA, AND CANADA, ALL IMPLIED WARRANTIES,
INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR USE OR
PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE
DATE OF ORIGINAL PURCHASE. IN NO EVENT SHALL DACOR BE
LIABLE FOR INCIDENTAL EXPENSE OR CONSEQUENTIAL DAMAGES. NO WARRANTIES, EXPRESS OR IMPLIED, ARE MADE TO
ANY BUYER FOR RESALE.
If your DACOR product fails to function within one year of
the original date of purchase, due to a defect in material
or workmanship, DACOR will remedy the defect without
charge to you or subsequent users. The owner must provide proof of purchase upon request, and have the appliance accessible for service.
Some states do not allow limitations on how long an
implied warranty lasts, or do not allow the exclusion or
limitation of inconsequential damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have
other rights that vary from state to state.
Warranty
What Is Covered
CERTIFICATE OF WARRANTIES: DACOR WARMING
DRAWERS
WITHIN THE FIFTY STATES OF THE U.S.A., THE DISTRICT OF COLUMBIA, AND CANADA*:
Warranty is null and void if non-CSA approved product is
transported from the U.S.
8
fold here
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
BUSINESS REPLY MAIL
FIRST-CLASS MAIL
PERMIT NO. 4507
DIAMOND BAR CA
POSTAGE WILL BE PAID BY ADDRESSEE
DACOR
ATTN: WARRANTY PROCESSING DEPT
PO BOX 6532
DIAMOND BAR CA 91765-9861
Please visit www.Dacor.com to activate your warranty online.
WARRANTY INFORMATION
IMPORTANT:
Please rest assured that under no conditions will Dacor sell your name or any of the information on this form for mailing list purposes. We
are very grateful that you have chosen Dacor products for your home and do not consider the sale of such information to be a proper way
of expressing our gratitude!
Owner’s Name:
Street:
Last (Please Print or Type)
First
City:
Middle
State:
Purchase Date:
Email:
cut here
Your warranty will not be activated until you activate it online or return this form to Dacor. If you have purchased more
than one Dacor product, please return all forms in one envelope or activate the warranty for each product online.
Zip:
Telephone:
Dealer:
City:
State:
Zip:
Your willingness to take a few seconds to fill in the section below will be sincerely appreciated. Thank you.
1. How were you first exposed to Dacor products? (Please check one only.)
 A. T.V. Cooking Show
 F Builder
 B. Magazine
 G. Architect/Designer
 C. Appliance Dealer Showroom
 H. Another Dacor Owner
 D. Kitchen Dealer Showroom
 I. Model Home
 E. Home Show
 J. Other
2. Where did you buy your Dacor appliances?
 A. Appliance Dealer
 B. Kitchen Dealer
 C. Builder Supplier
 D. Builder
 E. Other
3. For what purpose was the product purchased?
 A. Replacement only
 B. Part of a Remodel
 C. New Home
 D. Other
4. What is your household income?
 A. Under $75,000
 B. $75,000 – $100,000
 C. $100,000 – $150,000
 D. $150,000 – $200,000
 E. $200,000 – $250,000
 F. Over $250,000
6. Would you buy or recommend another Dacor product?
 Yes
Comments:
cut here
5. What other brands of appliances do you have in your kitchen?
A. Cooktop
C. Dishwasher
B. Oven
D. Refrigerator
 No
Thank you very much for your assistance. The information you have
provided will be extremely valuable in helping us plan for the future
and giving you the support you deserve.
Place Serial Number Label Here
Web site:
Corporate phone:
www.Dacor.com
(800) 793-0093
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement