2461-20 | User manual | Milwaukee SERVICE PARTS LIST

BULLETIN NO.
SERVICE PARTS LIST
54-26-2400
REVISED BULLETIN
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M12™ 1/4" SQUARE IMPACT WRENCH
00
FIG.
5
8
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
EXAMPLE:
0 Component Parts (Small #) Are Included
When Ordering The Assembly (Large #).
PART NO.
14-30-0130
45-88-2135
--------------02-02-1300
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
STARTING
SERIAL NO.
2461-20
CATALOG NO.
51(1x)
DATE
June 2013
WIRING INSTRUCTION
F04A
SEE PAGE 2
49(5x)
67
47 48
60 40
49 50 51
DESCRIPTION OF PART
NO. REQ.
Gearcase Assembly with Bushing
(1)
Nylon Ring
(1)
1/4" Square Anvil
(1)
5.0mm Steel Ball
(1)
Hammer
(1)
3.0mm Steel Ball
(27)
Washer
(1)
Compression Spring
(1)
Retaining Ring
(1)
50(1x)
Washer
(1)
Washer
(1)
Ball Bearing
(1)
Gear Housing
(1)
4.7mm Steel Ball
(1)
29 30 31
Cam Shaft
(1) 62 32 33
2nd Stage Planet Gear
(4)
32
2nd Stage Ring Gear
(1)
31
2nd Stage Sun Gear and Carriage
(1)
1st Stage Planet Gear
(4) 30
1st Stage Ring Gear
(1)
Washer
(1)
69
47
36
63 34
37 44
46
68
45
37
36
66 60
63
48
40
41
42
44
33
61 41
42
34
28
27
43
26
25
24
29
27
23
=51(1x)
=50(1x)
=49(5x)
22
21
20
Model
2462-20 Shown
13 14 15 16 17 18 19 20
59 12
21 22 23 24 25 26 27 28
NOTE: Impact Assembly
#59 comes completely
assembled and
16
lubricated.
15
14
13
12
38
19
18
11
17
10
52
53
52
65 10
53
8
5
39
FIG.
29
30
31
32
33
34
36
37
38
39
40
41
42
43
44
45
46
47
PART NO.
----------------------------------------------------------------------------------------------------------------06-65-0022
06-65-0502
------------------------------------------42-70-0055
--------------45-24-0077
40-50-1135
---------------
26(4x)
DESCRIPTION OF PART
Motor Pinion
M3.0 Screw
Lock Washer
Motor Mounting Bracket
Motor
Switch
Battery Contact Plate
PCBA
M2.5 x 30mm Pin
M2.5 x 36.7mm Pin
Left Handle Halve
Belt Clip
M3.0 Screw
Housing Clip
LED Lens
Forward/Reverse Shuttle
Spring Plate
Right Handle Halve
NO. REQ.
(1)
(2)
(2)
(1)
(1)
(1)
(1)
(1)
(2)
(2)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
(1)
IMPORTANT:
If during Motor
replacement the
gearing from the
Impact Assembly
becomes dislodged, it is to be
Etched
noted that the
Holes
Ring Gears #24
and #27 and the
Planet Gears #23 and #26 look the same but are
different! The 1st stage gearing (26 and 27) are
marked with etched holes as shown. The 2nd stage
gearing will not have these markings.
FIG.
48
49
50
51
52
53
59
60
61
62
63
65
66
67
68
69
PART NO.
31-01-0003
06-82-1080
06-82-6350
06-82-7336
34-40-1880
44-90-1070
14-29-0022
31-50-0005
42-70-0490
23-30-0430
23-66-0212
42-06-1035
31-50-0315
12-20-2485
10-20-2952
42-55-2461
DESCRIPTION OF PART
NO. REQ.
Light Pipe
(1)
M3 x 14mm Pan Hd. Plast. T-10 Screw (5)
M3 x 16mm Pan Hd. Plast. T-10 Screw (1)
M3 x 20mm Pan Hd. Plast. T-10 Screw (1)
O-Ring - 1/4" Square Anvil
(1)
Friction Ring - 1/4" Square Anvil
(1)
Impact Assembly
(1)
Handle Set
(1)
Belt Clip Assembly
(1)
Motor Assembly
(1)
Electronics Assembly
(1)
1/4" Square Anvil Assembly
(1)
Handle/Electronics Assembly
(1)
Service Nameplate
(1)
Warning Label
(1)
Carrying Case
(1)
FIG.
LUBRICATION
(Type 'J' Grease, No. 49-08-4220):
5
Coat inside of bushing inside front gearcase with grease.
10
Lightly coat front washer surface of anvil (10) with grease.
29
Coat pinion of motor assembly (62) with grease.
MILWAUKEE ELECTRIC TOOL CORPORATION
13135 W. Lisbon Road, Brookfield, WI 53005
Drwg. 4
NOTE:
When installing Motor Assembly #62, orient the motor
with the slot in the motor canister to the bottom
and the positive terminal (marked with a
red dot) to the inside of Left Handle
Halve #40. Solder the red wire from
the top left position of the switch
+
to the positive motor terminal.
Solder the black wire from the
top right position of the switch
to the negative terminal on motor.
Red switch
wire
Black switch wire
Slot
= WIRE TRAPS
or GUIDES
MOTOR
ASSEMBLY #62
PRINTED CIRCUIT
BOARD ASSEMBLY
(PCBA) #37
LED LENS #44
ON/OFF
SWITCH #34
BATTERY
CONTACT
PLATE #36
AS AN AID TO REASSEMBLY, TAKE NOTICE OF WIRE
ROUTING AND POSITION IN WIRE GUIDES AND
TRAPS WHILE DISMANTLING TOOL.
BE CAREFUL AND AVOID PINCHING WIRES
BETWEEN HANDLE HALVES WHEN ASSEMBLING.