User Manual

Add to my manuals
24 Pages

advertisement

User Manual | Manualzz

AVS-HDB-WPTX

Video Extender - 4K HDMI, VGA, RS-232, Wallplate Transmitter with Audio

User Manual

Provides a wallplate interface for HDMI/VGA input sources.

Customer

Support

Information

Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)

FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax

724-746-0746 • www.blackbox.com • [email protected]

Trademarks Used in this Manual

Trademarks Used in this Manual

Black Box and the Double Diamond logo are registered trademarks of

BB Technologies, Inc.

Any other trademarks mentioned in this manual are acknowledged to be the property of the trademark owners.

Page 2 724-746-5500 | blackbox.com

FCC and IC RFI Statements/NOM Statement

FEDERAL COMMUNICATIONS COMMISSION AND

INDUSTRY CANADA RADIO FREQUENCY INTERFERENCE STATEMENTS

This equipment generates, uses, and can radiate radio-frequency energy, and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause inter ference to radio communication.

It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when the equipment is operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his own expense will be required to take whatever measures may be necessary to correct the interference.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This digital apparatus does not exceed the Class A limits for radio noise emis sion from digital apparatus set out in the Radio Interference Regulation of Industry Canada.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le

Règlement sur le brouillage radioélectrique publié par Industrie Canada.

Normas Oficiales Mexicanas (NOM)

Electrical Safety Statement

INSTRUCCIONES DE SEGURIDAD

1. Todas las instrucciones de seguridad y operación deberán ser leídas antes de que el aparato eléctrico sea operado.

2. Las instrucciones de seguridad y operación deberán ser guardadas para referencia futura.

3. Todas las advertencias en el aparato eléctrico y en sus instrucciones de operación deben ser respetadas.

4. Todas las instrucciones de operación y uso deben ser seguidas.

724-746-5500 | blackbox.com

Page 3

NOM Statement

4. Todas las instrucciones de operación y uso deben ser seguidas.

5. El aparato eléctrico no deberá ser usado cerca del agua—por ejemplo,

cerca de la tina de baño, lavabo, sótano mojado o cerca de una alberca,

etc..

6. El aparato eléctrico debe ser usado únicamente con carritos o pedestales

que sean recomendados por el fabricante.

7. El aparato eléctrico debe ser montado a la pared o al techo sólo como sea

recomendado por el fabricante.

8. Servicio—El usuario no debe intentar dar servicio al equipo eléctrico más allá

lo descrito en las instrucciones de operación. Todo otro servicio deberá ser

referido a personal de servicio calificado.

9. El aparato eléctrico debe ser situado de tal manera que su posición no

interfiera su uso. La colocación del aparato eléctrico sobre una cama, sofá,

alfombra o superficie similar puede bloquea la ventilación, no se debe

colocar en libreros o gabinetes que impidan el flujo de aire por los orificios

de ventilación.

10. El equipo eléctrico deber ser situado fuera del alcance de fuentes de calor

como radiadores, registros de calor, estufas u otros aparatos (incluyendo

amplificadores) que producen calor.

11. El aparato eléctrico deberá ser connectado a una fuente de poder sólo del

tipo descrito en el instructivo de operación, o como se indique en el

aparato.

12. Precaución debe ser tomada de tal manera que la tierra fisica y la

polarización del equipo no sea eliminada.

13. Los cables de la fuente de poder deben ser guiados de tal manera que no

sean pisados ni pellizcados por objetos colocados sobre o contra ellos,

poniendo particular atención a los contactos y receptáculos donde salen

del aparato.

14. El equipo eléctrico debe ser limpiado únicamente de acuerdo a las

recomendaciones del fabricante.

15. En caso de existir, una antena externa deberá ser localizada lejos de las

lineas de energia.

Page 4 724-746-5500 | blackbox.com

NOM Statement

16. El cable de corriente deberá ser desconectado del cuando el equipo no sea

usado por un largo periodo de tiempo.

17. Cuidado debe ser tomado de tal manera que objectos liquidos no sean

derramados sobre la cubierta u orificios de ventilación.

18. Servicio por personal calificado deberá ser provisto cuando:

A: El cable de poder o el contacto ha sido dañado; u

B: Objectos han caído o líquido ha sido derramado dentro del aparato; o

C: El aparato ha sido expuesto a la lluvia; o

D: El aparato parece no operar normalmente o muestra un cambio en su

desempeño; o

E: El aparato ha sido tirado o su cubierta ha sido dañada.

724-746-5500 | blackbox.com

Page 5

Safety Precautions

Safety Precautions

For reliable operation of the equipment and personnel safety, follow the guidelines below for installation, use, and maintenance of the device.

1. The system must be grounded properly. Do not use two-blade plugs and ensure the alternating power supply ranges from 100 to 240 VAC and 50 to 60 Hz.

2. Do not put the control panel in an environment that is not within the its temperature tolerance.

3. Because the switch’s power generates heat when running, be sure the working environment is properly ventilated to avoid damage caused by equipment overheating.

4. Turn off the general power switch in humid weather or when the control panel will be left unused for long time.

5. Before operating, be sure that the alternating current wire is pulled out of the power supply.

6. NEVER open the casing of the equipment, DO NOT repair it on your own. This might be harmful to persons or the equipment.

7. DO NOT splash any liquids on or around the equipment.

Page 6 724-746-5500 | blackbox.com

Table of Contents

Table of Contents

1. Specifications ..............................................................................................8

2. Overview .....................................................................................................9

2.1 Introduction .....................................................................................9

2.2 Features ...........................................................................................9

2.3 What's Included ..............................................................................10

2.4 Hardware Description .....................................................................10

2.4.1 Front Panel .............................................................................10

2.4.2 Side Panel ..............................................................................12

2.4.3 Back Panel .............................................................................12

3. System Connection ....................................................................................14

3.1 Usage Precautions...........................................................................14

3.2 Connection Procedure ....................................................................14

3.3 Powering On the Unit .....................................................................15

3.4 PoC Solution ...................................................................................15

3.5 Application .....................................................................................16

4. Operation ...................................................................................................17

4.1

4.2

Front-Panel Buttons ........................................................................17

RS-232 Communications Command ...............................................19

5. Troubleshooting and Maintenance .............................................................23

724-746-5500 | blackbox.com

Page 7

Chapter 1: Specifications

1. Specifications

Video

Input

Input Connector

Output

(1) HDMI, (1) VGA

(1) 19-pin Type A HDMI F, (1) 15-pin VGA

(1) HDBaseT

Output Connector

Transmission Mode

Audio

Input

Input Connector

Frequency Response

Impedance

(1) RJ-45

HDBaseT

(1) synchronous VGA audio

(1) 3.5-mm stereo jack

20 Hz–20 kHz

>10 ohms, ASNR, >85 dB @ 20 Hz–20 kHz

Control Ports

Control Ports (1) 3-pin RS-232 socket on front panel,

(1) 3-pin RS-232 socket on rear panel (shares the grounding pole with 12 V output)

General

Resolution VGA: 800 x 600, 1024 x 768, 1280 x 800,1280 x 1024,

1440 x 900,1600 x 1200,

1920 x 1080, 1920 x 1200;

HDMI: 4Kx2K, 1080p 3D, 1080P(HD)/1080i/720P/576P/576 i/480P/480i

Transmission Distance 1080P < or = 60 m (PoC)

4K x 2K < or = 40 m (PoC)

Bandwidth

HDMI Standard

Hardware

Chassis Style

10.2 Gbps

Support HDMI1.4 and HDCP

Dimensions

Weight

Decora-style wall-gang

4.1"H x 3.5"W x 1.7"D (10.4 x 8.9 x 4.4 cm)

0.63 lb. (0.29 kg)

Environmental

Operating Temperature -14 to 104° F (-10 to +40° C)

Operating Humidity 10–90%

Page 8 724-746-5500 | blackbox.com

Chapter 2: Overview

2. Overview

2.1 Introduction

The Video Extender —4K HDMI, VGA, RS-232, Wallplate Transmitter with Audio (AVS-

HDB-WPTX) is a Decora style transmitter that installs in a double-gang wall box to provide a convenient interface for HDMI/VGA input sources. It has (1) HDMI IN, (1) VGA IN and (1) HDBaseT OUT with PoC connector. It supports VGA as a full HD scale. HDMI 1.4 with 4k and 3D input signals support auto-switching and manual-switching. The

HDBaseT output supports 60-m UHD video transmission with PoC, and enables bi-directional RS-232 communication between the AVS-HDB-WPTX and the remote device.

Using PoC, AVS-HDB-WPTX can be powered via a far-end PoC receiver.

2.2 Features

• Selectable HDMI/VGA with audio input

• Supports VGA output resolution up to 1920x1200

• High bandwidth: 10.2 Gbps

• Built-in scaler, scales HDMI/VGA signals to match the native resolution of the display.

• Transmits HDMI signals up to 4K

• Compliant with HDMI 1.4, support 1080p 3D

• HDCP compliance, equipped with HDCP auto-tracking solution

• Provides auto-switching capability

• Supports multiple control methods including front-panel buttons, and RS-232. The extender supports bi-directional RS-232 passthrough control.

• Supports firmware upgrading via USB.

• Powered by a 12-VDC power output or PoC connection up to 60 m.

• Made of aluminum, so it cools faster.

724-746-5500 | blackbox.com

Page 9

Chapter 2: Overview

2.3 What's Included

Your package should include the following items. If anything is missing or damaged, contact Black Box Technical Support at 724-746-5500 or [email protected].

• (1) Video Extender —4K HDMI, VGA, RS-232, Wallplate Transmitter with Audio (AVS-

HDB-WPTX)

• (4) Screws (for AVS-HDB-WPTX)

• (3) Pluggable Terminal Blocks ([1] 2-pin block, [1] 3-pin block, and [1] 4-pin block)

• (1) Faceplate

• (4) Screws (for the faceplate)

• (1) Power Adapter (12-VDC, 2-A, selectable)

• This printed user manual

2.4 Hardware Description

2.4.1 Front Panel

7 8

1

2

3 6

4

5

9

Figure 2-1. Front panel.

Page 10 724-746-5500 | blackbox.com

Chapter 2: Overview

Table 2-1. Components.

8

9

Number Name

1 Power LED

2 SOURCE/AUTO button

3

4

5

6

7

RS-232 Serial port, 3-pin pluggable terminal block

VGA IN LED

AUDIO IN

HDMI IN

LINK and HDCP LED

RESET button

USB

Description

Lights red when power is on.

• Used as video source selection button (with backlight off): Press to select one source, press again to select next source, switching circularly between HDMI and VGA. The indicator of the selected input source will light green.

• Used as switching mode selection button (with backlight on):

Press and hold for 3 seconds or more to enter Auto-switching mode. The LED lights green when the unit is in auto-switching mode. Press and hold the button for 3 seconds or longer to enter in Manual-switching mode.

This connects to the control terminal to control the AVS-HDB-

WPTX, and supports bi-directional RS-232 control (send control signal from local or transmitter, send receive control signal from far-end devices).

Connects to VGA source device.

• Lights yellow when there is a VGA signal input.

• Lights green when the signal source is chosen as the input source.

• Off when there is no VGA input signal.

Connect with the audio output socket of VGA source device, deliver synchronous audio source with VGA signal source when choosing VGA as source signal.

Connect to HDMI source device.

• Lights yellow when there is an HDMI signal input.

• Lights green when the signal source is the input source.

• Off when there is no HDMI input signal.

LINK: Twisted Pair Link status indicator, lights green when successfully connected.

• HDCP: HDCP compliance indicator, lights green when the source signals is HDCP; blinks when it is not HDCP; and turns off when there is no source signal.

Press this button to reboot the AVS-HDB-WPTX.

Used for firmware update. Plug a flash disk or other storage device with update file (MERGE.bin), and send command

50698% to update the firmware.

724-746-5500 | blackbox.com

Page 11

Chapter 2: Overview

2.4.2 Side Panel

Figure 2-2. Side panel.

1. HDBaseT OUT: RJ-45 port, connect to a receiver via a CAT5e/6 cable to deliver

Audio/Video signals, supports PoC.

NOTE: AVS-HDB-WPTX supports unidirectional PoC. It can be powered the by far-end receiver but it can’t power the far-end receiver.

2.4.3 Back Panel

Figure 2-3. Back panel.

Page 12 724-746-5500 | blackbox.com

Chapter 2: Overview

2

3

Number Name

1 Power In

Power out

RS-232 serial port

Table 2-2. Back panel components.

Description

Power in port, 2-pin pluggable terminal block, connects to

12-VDC power adapter.

Power out port, connects to AVS-CTRL8 to power it with a

12-VDC power output.

Connects to a far-end receiver, supports bi-directional RS-232 control leads (sends the control signal from local devices or receives the control signal sent from far-end devices.

724-746-5500 | blackbox.com

Page 13

Chapter 3: System Connection

3. System Connection

3.1 Usage Precautions

1. Install the system in a clean environment that has a proper temperature and humidity.

2. Make sure that all the power switches, plugs, sockets, and power cords are insulated and safe.

3. Connect all devices before powering on.

AVS-HDB-RX

Blu-ray ™

Figure 3-1. Connections.

3.2 Connection Procedure

Step 1: Connect an HDMI source device (e.g. Blu-ray DVD) to the HDMI input port of the AVS-HDB-WPTX with HDMI cable. Connect a VGA source device (e.g. PC) to the VGA input port of the AVS-HDB-WPTX with VGA cable.

Step 2: Connect a AVS-HDB-RX to the HDBaseT port on the rear panel with twisted pair.

Step 3: Connect a HDMI display to the HDMI OUT port of AVS-HDB-RX.

Page 14 724-746-5500 | blackbox.com

Chapter 3: System Connection

Step 4: Connect a control terminal to the RS-232 port on the front panel of the

AVS-HDB-RX.

Step 5: Connect a control device (e.g. PC) to the RS-232 port of the AVS-HDB-WPTX or the AVS-HDB-RX (bi-directional RS-232 control, either is available).

Step 6: Connect the 24-VDC power adapter to the power port of the AVS-HDB-RX.

AVS-HDB-WPTX can get power from AVS-HDB-RX via PoC.

NOTE: AVS-HDB-WPTX supports unidirectional PoC, i.e, AVS-HDB-WPTX can get power from far-end PoC devices with PoC function, but it can’t power far-end PoC devices when the power supply is connected to the AVS-HDB-WPTX.

3.3 Powering On the Unit

AVS-HDB-WPTX has a 12-V power output port on the rear panel. Connect the 12-VDC power output port of the AVS-HDB-WPTX to the power port of the AVS-CTRL8 (refer to the following figure). AVS-HDB-WPTX can power the AVS-CTRL8.

AVS-CTRL8

Figure 3-2. Power connections.

3.4 PoC Solution

AVS-HDB-WPTX has a HDBaseT OUTPUT port on the rear panel, which can extend

HDMI/ VGA signals up to 60 m. It also supports PoC, which allows several terminals to share the same power supply and eliminates the need for an extra power supply at the remote nodes.

724-746-5500 | blackbox.com

Page 15

Chapter 3: System Connection

Connect a 24-VDC power adapter to the power port of AVS-HDB-RX. AVS-HDB-WPTX can be powered synchronously via PoC.

Figure 3-3. PoC connections.

3.5 Application

Use the AVS-HDB-WPTX for computer monitoring, conference rooms, large-screen displays, television, education applications and more.

Page 16 724-746-5500 | blackbox.com

Chapter 4: Operation

4. Operation

4.1 Front-Panel Buttons

AVS-HDB-WPTX has a channel switching button on the front panel, through which users can switch input source signals.

It supports both manual switching and auto switching. (The default setting is Auto switching.) Press and hold the switching button for 3 seconds or send command

“50770% “ and “50771%” to switch between the two modes.

Switching modes:

• Auto switching mode: In this mode, the indicator will light green, and

AVS-HDB-WPTX will recognize the last connected source device as the input source automatically.

• Disconnect the present source device, and it will deliver the other source signal (if there is an input signal on the other source).

• Manual switching mode: In this mode, the indicator will remain off. Press the switching button to select the input source, it will switch circularly between HDMI and

VGA. Or switch it by sending RS-232 commands. The indicator of the selected input source will light green.

4.2 RS-232 Control

RS-232 can be transmitted bi-directionally between AVS-HDB-WPTX and AVS-HDB-RX, so it can control a third-party RS-232 device locally or control an AVS-HDB-WPTX from remotely. To control a third-party RS-232 device, set the baud rate of this device to

2400, 4800, 9600, 19200, 38400, 57600, or 115200.

724-746-5500 | blackbox.com

Page 17

Chapter 4: Operation

Accessing through Serial

1. Using the client, select “serial” and enter “115200” for the speed (baud rate).

Figure 4-1. PuTTY configuration screen using serial.

2. No username or password is required. Just press enter.

Set the COM number, baud rate, data bit, stop bit, and parity bit correctly so you can send commands in the Command Sending Area of the screen.

NOTE: To control the AVS-HDB-WPTX via an RS-232 port, configure the communication protocol parameters as: Baud rate: 9600; Data bit: 8; Stop bit: 1; Parity bit: none.

Page 18 724-746-5500 | blackbox.com

Chapter 4: Operation

4.2 RS-232 Communication Commands

Table 4-1. RS-232 commands.

Switch Commands

Command Function

50701% Switch to HDMI input

Feedback Example

Switch to HDMI

50704% Switch to VGA input

50705% Change the horizontal polarity to the opposite.

Switch to VGA

Hpolarity:0/1

50706% Change the vertical polarity to the opposite. Vpolarity:0/1

50707% Check the present resolution and polarity.

1920 x 1080

Hpolarity:1

Vpolarity:0

50770% Enable auto-switching

50771% Disable auto-switching

Auto Switching

Manual Switching

Resolution Commands

Command Function

50619% Change the resolution to 1360 x 768 HD

Feedback Example

Resolution: 1360 x 768

50626% Change the resolution to 1024 x 768 XGA Resolution: 1024 x 768

50627% Change the resolution to 1280 x 720 720P Resolution: 1280 x 720

50628% Change the resolution to 1280 x 800

WXGA

Resolution: 1280 x 800

50629% Change the resolution to 1920 x 1080

1080P

50620% Change the resolution to 1920 x 1200

WUXGA

50621% Change the resolution to 1600 x 1200

UXGA

Resolution: 1920 x 1080

Resolution: 1920 x 1200

Resolution: 1600 x 1200

NOTE: Commands with grey background are for VGA sources only.

724-746-5500 | blackbox.com

Page 19

Chapter 4: Operation

Table 4-1 (continued). RS-232 commands.

Setup Commands

Command Function

502xx%

503xx%

504xx%

Set the brightness to xx. XX ranges from 00 to 99.

Set the contrast to xx. XX ranges from 00 to 99

Set the saturation to xx. XX ranges from 00 to 99.

Feedback Example

Brightness: xx

Contrast: xx

Saturation: xx

505xx%

50606%

50607%

50608%

50614%

Set the sharpness to xx. XX ranges from 00 to 99.

Auto-adjust the input parameter.

Adjust the color temperature.

Set the aspect ratio.

Set the picture mode.

50699% Check the system version.

50779% Switch to RS-232 mode 1, enable scaler to control far-end devices.

50780% Switch to RS-232 mode 2, enable far-end devices to control scaler.

50790% Set the HDCP status of the HDMI output socket to Active.

Sharpness: xx

VGA Input Auto

Color Temperature: xx (xx can be medium, warm, user, or cool)

Aspect Ratio: xx (xx can be

16:9, 4:3, or auto.)

Picture Mode: xx (xx can be dynamic, standard, mild, or user.)

Version Vx.x.x

RS-232 Mode 1: RS-232 Control

Scaler and Remote

RS-232 Mode 2: RS-232 and

Remote Control Scaler

HDCP Active

50791% Set the HDCP status of HDMI output socket to On.

HDCP On

50792% Set the HDCP status of HDMI output socket to Off.

HDCP Off

50698% Software update.

NOTE: Commands with grey background are for VGA sources only.

Page 20 724-746-5500 | blackbox.com

Chapter 4: Operation

Table 4-1 (continued). RS-232 commands.

Setup Commands (continued)

Command Function

50617% Reset to factory default.

Feedback Example

Inquire Commands

Command Function

50632%

50633%

50793%

Check the output resolution .

Check the picture mode.

Check HDCP status.

Feedback Example

Resolution: xx

Picture Mode: xx

HDCP Off

HDCP On

HDCP Active

50635% Check the image aspect ratio.

50636% Check the brightness.

50637% Check the contrast.

50638% Check the saturation.

Aspect Ratio: xx

Brightness: xx

Contrast: xx

Saturation: xx

50639% Check sharpness.

50640% Check the color temperature.

Sharpness: xx

Color Temperature: xx

Adjustment Commands

50678% Enable screen output adjusting. Enter Output Position Adjust

50679%

50670%

50671%

50672%

50673%

Disable screen output adjusting.

Move the image to left.

Move the image to right.

Move the image up.

Move the image down.

50674% Stretch left from left side (increase image width).

50675% Pull right from left side (decrease image width).

50676% Stretch upwards from bottom side

(decrease image height).

50677% Stretch downwards from bottom side.

Exit Output Position Adjust

Output Position Adjust X xx

Output Position Adjust X xx

Output Position Adjust Y xx

Output Position Adjust Y xx

Output Width Adjust xx

Output Width Adjust xx

Output Height Adjust xx

Output Height Adjust xx

(increase image height)

724-746-5500 | blackbox.com

Page 21

Chapter 4: Operation

Table 4-1 (continued). RS-232 commands.

EDID Commands

Command Function Feedback Example

50772% EDID passthrough

50773% Set EDID passthrough

EDID: bypass mode

EDID:1080P&PCM 2ch

50774% Set EDID data to 1080P Dolby 5.1

EDID:1080P&5.1ch

50775% Set EDID data to 1080P3D Dolby 5.1 EDID:1080P3d&5.1ch

50776% Set EDID data to 1080i PCM 2.0ch

EDID:1080i&PCM 2ch

50777% Set EDID data to 4K*2K PCM 2.0ch

EDID:4K&PCM 2ch

50778% Check EDID data

50799% Program EDID file, send EDID data within 10s

EDID:1080P&PCM 2ch

EDID:1080P&5.1ch

EDID:1080P3d&5.1ch

EDID:4K&PCM 2ch

Waiting for edid within 10 secs!

NOTES:

1. EDID commands are for HDMI sources only.

Page 22 724-746-5500 | blackbox.com

Chapter 5: Troubleshooting

5. Troubleshooting

Problems/Causes/Solutions

Table 5-1. Problems/Causes/Solutions.

Problems

Losing color or no video signal output in HDMI display.

No HDMI signal output in

AVS-HDB-4TX while local

HDMI input is in normal working state.

Output image has snowflake pattern.

Causes

The cables may not be connected correctly or may be broken.

The connecting cable’s quality is bad.

Failed or loose connection.

Solutions

Check whether the cables are connected correctly and are in working condition.

Try another high-quality cable.

Make sure the connection is good.

POWER indicator doesn’t work or does not respond to any operation.

Cannot control the device by control device (e.g. a PC) through RS-232 port.

Static becomes stronger when connecting the video connectors.

Cannot control the device through RS-232 port or frontpanel buttons.

Power cord connection failed.

Make sure the power cord connection is good.

Wrong RS-232 communication parameters.

Bad grounding.

Make sure the RS-232 communication parameters are correct.

Check the grounding and make sure it is connected well.

The unit might be broken. Contact Black Box

Technical Support at

724-746-5500 or [email protected].

If your problem persists after you follow the above troubleshooting steps,contact Black

Box Technical Support at 724-746-5500 or [email protected].

724-746-5500 | blackbox.com

Page 23

Black Box Tech Support: FREE! Live. 24/7.

Tech support the way it should be.

Great tech support is just 60 seconds away at

724-746-5500 or blackbox.com.

About Black Box

Black Box provides an extensive range of networking and infrastructure products. You’ll find everything from cabinets and racks and power and surge protection products to media converters and Ethernet switches all supported by free, live 24/7

Tech support available in 60 seconds or less.

© Copyright 2015. Black Box Corporation. All rights reserved. Black Box ® and the Double Diamond logo are registered trademarks of BB Technologies, Inc. Any third-party trademarks appearing in this manual are acknowledged to be the property of their respective owners.

AVS-HDB-WPTX, version 1

724-746-5500 | blackbox.com

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement