USAGE RESTRICTIONS
BOX M 240
Operation is not guaranteed when installed in different equipment than the specified one.
THE USAGE INSTRUCTIONS OF THIS DEVICE SHALL BE HANDED TO THE USER, WHO WILL
HAVE THEM IN THEIR POSSESSION. IF THEY ARE MISLAID, THE USER CAN ASK FOR A COPY
OR DOWNLOAD IT DIRECTLY FROM WWW.SMINN.COM
The manufacturer reserves the right to change the specifications of these systems as well as
this manual without prior warning. The equipment must be manipulated only by specialized
and/or skilled personnel.
FOUR CHANNEL RECEIVER
INSTRUCTION MANUAL
WARRANTY
This product has undergone a complete TEST during its manufacturing process that guarantees
its reliability and proper operation. The manufacturer provides 24 months of warranty to the
product from the date printed in the product and against any anomaly that it may present in its
appearance or operation.
Any damage caused by third parties, natural causes (flooding, fire, lightning, etc), arising from
improper handling or installation, vandalism or any other cause non attributable to the
manufacturer will void the warranty. The warranty only covers repairs or replacement of the
damaged device.
Any expenses derived from assembling, travelling, transport, natural wear of parts, etc., and, in
general, any expenses that are not part of the repairs or replacement of the damaged element
of the system are excluded.
The installer/provider will ask the manufacturer for a RMA number or authorization for
transport of the system in warranty. Without this previous requisite, the manufacturer will not
be able neither to process nor provide warranty service.
WARNING
This product must be used in installations which has been conceived for, considering any other
as improper use. The packaging must not be dumped in the environment. Keep products,
packaging, wrapping, documentation, etc., out of the reach of children. Follow the current local,
national or European regulations. The information contained in this document may have some
mistakes that will be corrected in future editions. The manufacturer reserves the right to modify
the contents of this document or the product without any prior warning.
WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE)
In accordance with the European Directive 2002/96/EC about waste electrical and electronic
equipment (WEEE), the presence of this symbol (see symbol at the bottom of this text) in the
product or in the packaging, means that this article shall not be disposed in local non-classified
waste streams. It is the user’s responsibility to dispose this product taking it to a collection
point designed for waste recycling of electrical and electronic devices. The separate collection
of this product helps optimize the waste sorting and recycling of any recyclable material and
also decreases the impact on health and the environment. For more information about the
correct wasting of this product, please contact the local authority or the distributor where you
acquired this product.
innovative in electronics
CE DECLARATION OF CONFORMITY
The company
Declares
The product:
ELSON SISTEMAS, S.L
Pol. Torrelarragoiti, P6-A3-1ª
48170 Zamudio - Bizkaia (SPAIN)
DESCRIPTION
SMINN's four channels receivers are developed with state-ofthe-art electronic devices. They provide a high degree of
operating reliability and security.
They are designed to provide the activation and movement
order to SMINN motor controllers, alarms, access control and
home automation systems, etc.
They are suitable for industrial, commercial and/or residential
enviroments.
Four channel Receiver BOX M 240
Manufactures by
ELSON ELECTRÓNICA, S.A.
Under the trademark:
SMINN
For use in:
enviroments.
Residential, Commercial or light industry
This device meets the provisions contained in the article 3 of the
R&TTE1999/05/CE Regulation, as long as its usage is compilant to what
was envisaged, having applied the following regulations:
Telecommunications:
Electromagnetic
compatibility:
Low Voltage
EN 300 220-1 v1.3.1 (2000-09)
EN 300 220-1 v1.1.1 (2000-09)
These devices are built using high quality materials and
components and the latest technology. They are devices that
observe the current regulations for usage in residential,
commercial and light industry environments.
EN 301489-1 v1.3.1 (2001-09)
EN 301489-3 v1.3.1 (2001-11)
EN 60730-1:2000
2012-03-30 Zamudio
Jose Miguel Blanco Perez
Chief Technical Officer
innovative in electronics
T. +34 944 525 120
www. sminn.com
[email protected]
Pol. Torrelarragoiti, P6 - A3 - 1º
48170 Zamudio Bizkaia
SPAIN
Rev. 2114
Elson Sistemas
OPERATION
When a code from a SMINN emitter is recived, the receiver checks if it is already registered in any of
4 inserted memories. If it si registered and not blocked, the relay will activate.
ERASE MEMORY
The memory can only be erased using SMINN´s programming console and knowing its PIN,
avoiding accidental or malicious erasures.
BLOCKING A CODE IN THE MEMORY
A transmitter code cannot be simply erased from the memory, but it can be blocked so it won´t
work anymore. Blocking codes in the memory can only be done using a SMINN programming
console and knowing its PIN.
TRANSMITTER RECORDING
SMINN BOX M receivers can store up to 2000 transmitters in each of the inserted memories
(depending on memory capacity 500 / 1000 / 2000). Before recording any transmitter,
we must make sure that the memories are formatted and configured correctly with an SMIINN
programming console.
Security Level 1 (basic) .- Knowing the PIN it is possible to program a transmitter with the SMINN
programming console that will just record itself in the receiver memory.
Security Level 2 (medium) .- Only a transmitter that is already recorded can grant permission for
self-recording to transmitters with the same PIN.
Security Level 3 (high) .- Recording can only be done manually and with transmitters programmed
with the installation PIN.
TECHNICAL CHARACTERISTICS
433.92 MHz
868.3 MHz
433.92 MHz
868.3 MHz
BOX M 240
BOX M 280
BOX M 244
BOX M 284
RADIO
Sensibility
Radio
Encoding
Antenna
Min./Max. consumption at 12/24VDC
RECORDING VIA RADIO
Depending on the memory security level it is possible to record transmitters via radio
(permission grant or invite).
Recording via permission grant (Security levels 1 or 2)
• Press and hold the first and second buttons of a recorded transmitter (MASTER transmitter).
• Wait until the transmitter led powers on (5 seconds).
• Release the transmitter buttons (The led stays powered on, LEARNING MODE).
• Make sure you are close to the receiver (1 to 10m).
• Press and hold the first button of the MASTER transmitter.
• Wait for the validation beep (Memory open for 8 seconds).
• Press and hold the working channel button of the transmitter we want to record.
• Wait for the validation beep.
• Release the button of the new transmitter.
Recording via invite
A transmitter can be invited with an already recorded transmitter (security levels 1 and 2) or using
an SMINN programming console (security level 1).
To invite a transmitter follow these instructions:
• Press and hold the first and second buttons of a recorded transmitter (MASTER transmitter).
• Press and hold the first and second buttons of a new transmitter (it must have the same PIN).
• Wait until both trnasmitter leds power on (5 seconds).
• Release the transmitters buttons (leds stay powered on, LEARNING MODE).
• Place the MASTER transmitter close to the new transmitter, with its LED touching the
SYNC AREA of the new transmitter.
• Press and hold the first button of the MASTER transmitter.
• Wait until the new transmitter blinks slowly 5 times.
• Release the button of the MASTER transmitter.
• Make sure you are close to the receiver (1 to 10m).
• Press and hold the working channel button of the transmitter we want to record.
• Wait for the validation beep.
• Release the button of the new transmitter.
TRANSMITTER REPLACEMENT
With this function it is possible to replace a transmitter code from a memory with a new one.
This functon is useful in case of loss or breakage.
This function can only be performed using the SMINN programming console and knowing the PIN
of the installation and the code of the lost transmitter.
.
BACKUP COPY
Although the device is protected against power line disturbances and electrical surges, it is
important to keep a backup of the memory card in case of breakdown or damages caused by
external circumstances such as electric storms, theft, improper handling, etc.
INSTALLATION
SMINN´s receiver is designed to be easily fixed on a wall using the suplied wall plugs and screws.
Before connecting or operating the device, the power supply switch or differential shall be
disconnected. Specialized and/or skilled personnel will do the installation, using properly protected
cable of enough gauge. Take into account that devices permanently connected to the mains need
to have an accessible connection device (i.e. a magnetothermic switch). The wiring should be done
following the instructions printed in he serigraphy of the circuit board. Make sure that the memory
is inserted and properly configured. After programming and verifying the equipment, close the
case with the supplied top.
SMINNRECEIVERSARE EQUIPPED WITH A LED TO LET KNOW
IF THE DEVICES IS POWERED
Note: Reinforced concrete, metallic components and/or any other receiving device reduce
dramatically the radiofrequency signal, so installation close to these elements should be avoided..
< -115 dBm
Superheterodine
High security Crypto/Rolling
Internal helicoidal
20mA / 80mA
COMMON
Power suply
Code memorization
Power output
Memory expansion
500 / 1000 / 2000
Operation Temperature
Dimensions
-20ºC / +85º C
182 x 145 x 65 mm (antenna not included)
Watertight
IP54 - (IP65 with cable glands)
230VAC (125VAC / 24V AC/DC optional)
4 plug-in memories of 250 codes
+15 VDC
The first transmitter, which must be manually recorded, sets the working channel for the entire
memory. Other transmitters may be recorded manually or via radio, usng the same channel as the
first transmitter.
MANUAL RECORDING
To manually record transmitters using the PROG button follow these instructions:
• Power on the device and wait 5 seconds
• Press and hold the PROG button for the desired memory (PROG.1/4)
• Press and hold the desired channel button of the transmitter we want to record.
• Notice the blinking led (SCAN mode).
• Wait for the validation beeps.
• Release the transmitter button.
• Release the PROG button (PROG.1/4).
Repeat these steps for each transmitter you want to record manually.
230 VAC
230 VAC
12/24 VAC/DC
12/24 VAC/DC
1
Fig.1
2
2
3
4
11
5
6
10
7
9
8
COMPONENTS
1.
2.
3.
4.
5.
6.
ON Led
Radio Module
Memory card
RUN Led
Radio PROG button
Relays
7.
8.
9.
10.
11.
Terminal strip
Power connector
Buzzer
Fuse 0.3A
Transformer (Depends on model)
WIRING
Wiring is easy using the terminal block for three circuits.
Power input, power output and relays.
Term. Function
1
2
3
4
5-6
7-8
9-10
11-12
Note
Power
Power
Positive (+)
Negative (-)
Power input 230V AC / 24V AC/DC
N.O.
N.O.
N.O.
N.O.
Cannal 1 Relay
Cannal 2 Relay
Cannal 3 Relay
Cannal 4 Relay
Contact
Contact
Contact
Contact
Power output 15VDC - 200mA MAX
">