AlpicAir AWO-100HPS3C Sigma series Manual

PDF

Document

AIR CONDITIONER

REMOTE CONTROLLER ILLUSTRATION

The design and specifications are subject to change without prior notice for product improvement. Consult with the sales agency or manufacturer for details.

Thank you very much for purchasing our air conditioner.

Please read this owner's manual carefully before using your air conditioner.

Remote controller Specifications...................................................

Operation buttons .................. .........................................................

Indicators on LCD ..........................................................................

How to use the buttons ................................................................. 7

Auto operation.................................................................................

Cooling/Heating/Fan operation......................................................

Dehumidifying operation ...............................................................

Adjusting air flow direction............................................................

Timer operation...............................................................................

Handling the remote controller ......................................................

NOTE:

Buttons design is based on typical model and might be slightly different from the

actual one you purchased the actual shape shall prevail.

All the functions described are accomplished by the unit. If the unit has no this

feature, there is no corresponding operation happened when press the relative

button on the remote controller.

, ,

, , ,,

USER'S MANUAL on function description, the description of USER'S MANUAL

shall prevail.

Remote Controller Specifications

Model

Rated Voltage

Signal Receiving

Range

Environment

RG57A3/BGEF,RG57A2/BGEF,RG57B/BGE,RG57D/BGE

3.0V(Dry batteries R03/LR03 2)

ON/OFF

MODE

SHORT

CUT

TIMER

TEMP

FAN

TIMER

OFF

SLEEP FRESH

TURBO SELF CLEAN LED FOLLOW ME

ON/OFF

MODE

FAN

TEMP

SHORT

CUT

TIMER

OFF

SLEEP FRESH SWING DIRECT

TURBO LED

RG57A2/BGEF

(FRESH button is not available)

RG57A3/BGEF

RG57B/BGE

(FRESH button is not available)

RG57D/BGE

1 2

Operation of buttons

ON/OFF

MODE

FAN

TEMP

SHORT

CUT

TIMER

OFF

SLEEP FRESH

TURBO SELF CLEAN

LED FOLLOW ME

RG57A3/BGEF

1 ON/OFF Button

This button turns the air conditioner ON and OFF.

2 MODE Button

Press this button to modify the air conditioner mode in a sequence of following:

AUTO COOL DRY HEAT

FAN

NOTE Please do not select HEAT mode if the machine you purchased is cooling only type.

Heat mode is not supported by the cooling only appliance.

FAN Button

Used to select the fan speed in four steps:

AUTO LOW MED HIGH

NOTE: You can not switch the fan speed in

AUTO or DRY mode.

SLEEP Button

Active/Disable sleep function. It can maintain the most comfortable temperature and save energy. This function is available on COOL, HEAT or AUTO mode only .

, , ,,

USER S MANUAL.

NOTE: While the unit is running under SLEEP mode, it would be cancelled if MODE, FAN

SPEED or ON/OFF button is pressed.

5 FRESH Button ( applicable to RG57A3/BGEF and

RG57D/BGE )

Active/Disable FRESH function. When the

FRESH function is initiated, the Ionizer/

Plasma Dust Collector(depending on models) is energized and will help to remove pollen and impurities from the air.

TURBO Button

Active/Disable Turbo function. Turbo function enables the unit to reach the preset temperature at cooling or heating operation in the shortest time(if the indoor unit does not support this function, there is no corresponding operation happened when pressing this button.)

SELF CLEAN Button ( applicable to Rg57(A2)A3/BGEF

Active/Disable Self Clean function

)

Operation of buttons

ON/OFF

MODE

FAN

SLEEP

TURBO

TEMP

SHORT

CUT

TIMER

OFF

SWING DIRECT

LED

RG57B/BGE

UP Button( )

Push this button to increase the indoor

DOWN Button( )

Push this button to decrease the indoor o

NOTE Temperature contol is not available in Fan mode.

SHORTCUT Button

Used to restore the current settings or resume previous settings.

On the first time connecting to the power, if push the SHORTCUT button, the unit o speed is Auto.

Push this button when remote controller is on, the system will automatically revert back to the previous settings including operating mode, setting temperature, fan speed level and sleep feature(if activated).

If pushing more than 2 seconds, the system will automatically restore the current operation settings including operating mode, setting temperature, fan speed level and sleep feature(if activated ).

TIMER ON Button

Press this button to initiate the auto-on time sequence. Each press will increase the auto-timed setting in 30 minutes increments. When the setting time displays

10.0, each press will increase the autotimed setting 60 minutes increments.

To cancel the auto-timed program, simply adjust the auto-on time to 0.0.

TIMER OFF Button

Press this button to initiate the auto-off time sequence. Each press will increase the auto

-timed setting in 30 minutes increments.

When the setting time displays 10.0, each press will increase the auto-timed setting

60 minutes increments. To cancel the autotimed program, simply adjust the auto-off time to 0.0

Operation of buttons

ON/OFF

MODE

FAN

TEMP

SHORT

CUT

TIMER

OFF

SLEEP FRESH

TURBO SELF CLEAN LED FOLLOW ME

RG57A2/BGEF

ON/OFF

MODE

SHORT

CUT

TIMER

TEMP

FAN

TIMER

OFF

SLEEP FRESH SWING DIRECT

TURBO LED

RG57D/BGE

Swing Button ( applicable to RG57(A2)A3/BGEF )

Used to stop or start vertical louver movement and set the desired left/right air flow direction.

The vertical louver changes 6 degree in angle area of indoor unit displays for one second. If keep pushing more than 2 seconds, the vertical louver swing feature is activated.

IIII

, , swing feature is stopped, it displays LC and remains on for 3 seconds.

Swing Button ( applicable to RG57A3(A2)/BGEF )

Used to stop or start horizontal louver movement or set the desired up/down air flow direction. The louver changes 6 degree in angle for each press. If keep pushing more than 2 seconds, the louver will swing up and down automatically.

SWING Button ( applicable to RG57B/BGE )

Used to stop or start horizontal louver auto swing feature.

DIRECT Button ( applicable to RG57B/BGE )

Used to change the louver movement and set the desired up/down air flow direction.

13 FOLLOW ME Button

( applicable to Rg57(A2)A3/BGEF )

Push this button to initiate the Follow Me feature, the remote display is actual temperature at its location. The remote control will send this signal to the air conditioner every 3 minutes interval until press the Follow Me button again. The air conditioner will cancel the Follow Me feature automatically if it does not receive the signal during any 7 minutes interval.

LED Button

Disable/Active indoor screen Display. When pushing the button, the indoor screen display is cleared, press it again to light the display.

Indicators on LCD

Information are displayed when the remote controller is powered up.

Mode display

AUTO COOL DRY

HEAT FAN

Displayed when data transmitted.

Displayed when remote controller is ON.

Battery display(low battery detection)

Not available for this unit

Displayed when TIMER ON time is set.

Displayed when TIMER OFF time is set.

Show set temperature or room temperature, or time under TIMER setting.

Displayed in Sleep Mode operation.

Indicated that the air conditioner is operating in Follow me mode

Not available for this unit

Fan speed indication

Low speed

Medium speed

High speed

Auto fan speed

Note:

All indicators shown in the figure are for the purpose of clear presentation. But during the actual operation only the relative functional signs are shown on the display window.

How to use the buttons

ON/OFF

MODE

FAN

TEMP

SHORT

CUT

TIMER

OFF

SLEEP FRESH

TURBO SELF CLEAN LED FOLLOW ME

ON/OFF

MODE

TEMP

FAN

SLEEP FRESH

TURBO SELF CLEAN LED FOLLOW ME

SHORT

CUT

TIMER

OFF

Auto operation

Ensure the unit is plugged in and power is available. The OPERATION indicator on the display panel of the indoor unit starts flashing.

1. Press the MODE button to select Auto.

2. Press the UP/DOWN button to set the

desired temperature. The temperature can

O O

increments.

3. Press the ON/OFF button to start the air

conditioner.

NOTE

1. In the Auto mode, the air conditioner can logically

choose the mode of Cooling, Fan, and Heating

by sensing the difference between the actual

ambient room temperature and the setting

temperature on the remote controller.

2. In the Auto mode, you can not switch the fan speed.

It has already been automatically controlled.

3. If the Auto mode is not comfortable for you , the

desired mode can be selected manually.

Cooling /Heating/Fan operation

Ensure the unit is plugged in and power is available.

1. Press the MODE button to select COOL,

HEAT(cooling & heating models only) or

FAN mode.

2. Press the UP/DOWN buttons to set the

desired temperature. The temperature can

O O

increments.

3. Press the FAN button to select the fan speed

in four steps- Auto, Low, Med,or High.

4. Press the ON/OFF button to start the air

conditioner.

NOTE

In the FAN mode, the setting temperature is not

displayed in the remote controller and you are not

able to control the room temperature either. In this

case, only step 1, 3 and 4 may be performed.

How to use the buttons

Dehumidifying operation

Ensure the unit is plugged in and power is available. The OPERATION indicator on the display panel of the indoor unit starts flashing.

1. Press the MODE button to select DRY mode.

2. Press the UP/DOWN buttons to set the

desired temperature. The temperature

3. Press the ON/OFF button to start the air

conditioner.

NOTE

In the Dehumidifying mode, you can not switch the

fan speed. It has already been automatically controlled.

ON/OFF

MODE

TEMP

FAN

SLEEP FRESH

TURBO SELF CLEAN LED FOLLOW ME

SHORT

CUT

TIMER

OFF

Adjusting air flow direction

Use the SWING & button to adjust the desired airflow direction.

1. Up/Down direction can be adjusted with the

button on the remote controller. Each

time when you press the button, the louver

moves an angle of 6 degree. If pressing more

than 2 seconds ,the louver will swing up and

down automatically.

2. Left/Right direction can be adjusted with the

button on the remote controller. Each

time when you press the button, the louver

moves an angle of 6 degree. If pressing more

than 2 seconds ,the louver will swing up and

down automatically.

NOTE: When the louver swing or move to a

position which would affect the cooling

or heating effect of the air conditioner,

it would automatically change the

swing/moving direction.

ON/OFF

MODE

TEMP

FAN

SLEEP FRESH

TURBO SELF CLEAN LED FOLLOW ME

SHORT

CUT

TIMER

OFF

Timer operation

Press the TIMER ON button can set the auto-on time of the unit. Press the TIMER OFF button can set the auto-off time of the unit.

To set the Auto-on time.

1. Press the TIMER ON button. The remote

controller shows TIMER ON, the last Auto-on

setting time and the signal "H" will be shown on

the LCD display area. Now it is ready to reset

the Auto-on time to START the operation.

2. Push the TIMER ON button again to set desired

Auto-on time. Each time you press the button,

the time increases by half an hour between 0

and 10 hours and by one hour between 10 and

24 hours.

3. After setting the TIMER ON ,there will be a one

second delay before the remote controller

transmits the signal to the air conditioner. Then,

after approximately another 2 seconds, the

signal "h" will disappear and the set temperature

will re-appear on the LCD display window.

To set the Auto-off time.

1. Press the TIMER OFF button. The remote

controller shows TIMER OFF, the last Auto-off

setting time and the signal "H" will be shown on

the LCD display area. Now it is ready to reset

the Auto-off time to stop the operation.

2. Push the TIMER OFF button again to set

desired Auto-off time. Each time you press the

button, the time increases by half an hour

between 0 and 10 hours and by one hour

between 10 and 24 hours.

3. After setting the TIMER OFF ,there will be a

one second delay before the remote controller

transmits the signal to the air conditioner. Then,

after approximately another 2 seconds, the

signal "H " will disappear and the set temperature

will re-appear on the LCD display window.

CAUTION

When you select the timer operation, the remote controller automatically transmits the

timer signal to the indoor unit for the specified time. Therefore, keep the remote

controller in a location where it can transmit the signal to the indoor unit properly.

The effective operation time set by the remote controller for the timer function

is limited to the following settings: 0.5, 1.0, 1.5, 2.0, 2.5, 3.0, 3.5, 4.0, 4.5, 5.0,

5.5, 6.0, 6.5, 7.0, 7.5, 8.0, 8.5, 9.0, 9.5, 10, 11, 12, 13, 14, 15,16,17, 18, 19, 20,

21, 22, 23 and 24.

Example of timer setting

Set

Off

Start

6 hours later

TIMER ON

(Auto-on Operation)

The TIMER ON feature is useful when you want the unit to turn on automatically before you return home. The air conditioner will automatically start operating at the set time.

Example:

To start the air conditioner in 6 hours.

1. Press the TIMER ON button, the last setting

of starting operation time and the signal "H"

will show on the display area.

2. Press the TIMER ON button to display "6.0H "

on the TIMER ON display of the remote

controller.

3. Wait for 3 seconds and the digital display

area will show the temperature again. The

"TIMER ON" indicator remains on and this

function is activated.

Stop

Set 10 hours later

Start

Set 2 hours later after setting

Stop

10 hours later after setting

TIMER OFF

(Auto-off Operation)

The TIMER OFF feature is useful when you want the unit to turn off automatically after you go to bed. The air conditioner will stop automatically at the set time.

Example:

To stop the air conditioner in 10 hours.

1. Press the TIMER OFF button, the last setting of

stopping operation time and the signal "H" will

show on the display area.

2. Press the TIMER OFF button to display "10H " on

the TIMER OFF display of the remote controller.

3. Wait for 3 seconds and the digital display area

will show the temperature again. The "TIMER

OFF" indicator remains on and this function is

activated.

COMBINED TIMER

(Setting both ON and OFF timers simultaneously)

TIMER OFF TIMER ON

(On Stop Start operation)

This feature is useful when you want to stop the air conditioner after you go to bed, and start it again in the morning when you wake up or when you return home.

Example:

To stop the air conditioner 2 hours after setting and start it again 10 hours after setting.

1. Press the TIMER OFF button.

2. Press the TIMER OFF button again to display

2.0H on the TIMER OFF display.

3. Press the TIMER ON button.

4. Press the TIMER ON button again to display 10H

on the TIMER ON display .

5. Wait for 3 seconds and the digital display area

will show the temperature again. The "TIMER

ON OFF" indicator remains on and this function is

activated.

Off

Set

2 hours later after setting

Start

Stop

5 hours later after setting

TIMER ON TIMER OFF

(Off Start Stop operation)

This feature is useful when you want to start the air conditioner before you wake up and stop it after you leave the house.

Example:

To start the air conditioner 2 hours after setting, and stop it 5 hours after setting.

1. Press the TIMER ON button.

2. Press the TIMER ON button again to display

2.0H on the TIMER ON display.

3. Press the TIMER OFF button.

4. Press the TIMER OFF button again to display

5.0H on the TIMER OFF display .

5. Wait for 3 seconds and the digital display area

will show the temperature again. The "TIMER

ON & TIMER OFF" indicator remains on and

this function is activated.

Handling the remote controller

Location of the remote controller.

Use the remote controller within a distance of 8 meters from the appliance, pointing it towards the receiver. Reception is confirmed by a beep.

CAUTIONS

The air conditioner will not operate if curtains, doors or other materials block the signals from the remote controller to the indoor unit.

Prevent any liquid from falling into the remote controller. Do not expose the remote controller to direct sunlight or heat.

If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may not function properly. Use curtains to prevent the sunlight from falling on the receiver.

If other electrical appliances react to the remote controller, either move these appliances or consult your local dealer.

Do not drop the remote controller. Handle with care.

Do not place heavy objects on the remote controller, or step on it.

Using the remote controller holder(optional)

The remote controller can be attached to a wall or pillar by using a remote controller holder(not supplied, purchased separately).

Before installing the remote controller, check that the air conditioner receives the signals properly.

Install the remote controller with two screws.

For installing or removing the remote controller, move it up or down in the holder.

Replacing batteries

The following cases signify exhausted batteries.

Replace old batteries with new ones.

Receiving beep is not emitted when a signal

is transmitted.

Indicator fades away.

The remote controller is powed by two dry batteries (R03/LR03X2) housed in the back rear part and protected by a cover.

(1) Remove the cover in the rear part of the

remote controller.

(2) Remove the old batteries and insert the new

batteries,placing the(+) and (-) ends correctly.

(3) Install the cover back on.

NOTE: When the batteries are removed, the remote controller erases all programming. After inserting new batteries, the remote controller must be reprogrammed.

CAUTIONS

Do not mix old and new batteries or batteries of different types.

Do not leave the batteries in the remote controller if they are not going to be used for

2 or 3 months.

Do not dispose batteries as unsorted municipal waste. Collection of such waste separately for special treatment is necessary.

Hello! I am an AI chatbot specifically trained to assist you with the AlpicAir AWO-100HPS3C Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!