Stream Flow Plus FP1 Water Filter User's Manual
Below you will find brief information for Water Filter Stream Flow Plus FP1. The Stream Flow Plus FP1 provides high-quality drinking water by filtering out contaminants and removing bad tastes and odors. This system is easy to install and maintain, and it can be connected to your sink or refrigerator for convenient access to clean water.
Advertisement
Advertisement
Logo Variation Tall
Logo Variation Horizontal tm
User’s Manu
al
Stream Flow Plus (FP1)
A-130317
Stream Drinking Water Systems
Thank you for choosing a Stream filtration system. It is our commitment to provide our valued customers the very best in water quality and we look forward to serving you for many years. Here’s how to connect
Stream and begin enjoying quality water for less.
Table of Contents
Sec.
01
General Information ..................................... 3
A. Operation & Maintenance
Specifications
B. Installation Overview & Parts
Preparing the Housing ................................. 5
A. Filter Cartridge Installation
Sec.
07
Connecting the
Drinking Water System .............................. 12
A. Adapter Connection
B. Tubing Connection
C. Ice Maker Connection
D. Placing Stream Flow Plus
Under the Sink
Start-up and Use ......................................... 14
A. Filter Life
Below the Sink Installation ........................ 6
A. Required Tool List
B. Attaching the Adapters to the Housing
C. Housing Assembly
Installing the Faucet ..................................... 8
A. Drill the Hole or Use Existing Hole
B. Mounting the Faucet
Connect to Plumbing ................................. 10
Performance Certification ......................... 15
Performance Data Sheets ......................... 16
A. Aesthetic Effects
B. Operational Specifications
C. California Certification
Troubleshooting & FAQs .......................... 20
A. Troubleshooting & FAQs
B. Maintenance Problems
Stream Laboratories, Inc.
2520 Shell Road Ste B
Georgetown, TX 78628
Phone: (888)-615-5733
StreamFilters.com
2
Table of Contents
A-130317
General Information
A. Operation & Maintenance Specifications
Model Number:
Replacement Filter Type:
Housing Composition:
Rubber Items:
Approximate Filter Capacity:
Approximate Flow Rate at 60 psi:
Maximum Working Pressure:
Minimum Working Pressure:
Maximum Operating Temperature:
Minimum Operating Temperature:
Inlet:
Outlet:
Particle Retention Size:
Certified by:
Stream Flow Plus (FP1)
Stream Flow Plus Cartridge Part (FC1)
Stainless Steel
Nitrile
750 gallons
0.75 gpm
100 psi / 8.8 kg/cm
2
30 psi / 2.1 kg/cm
2
100˚F / 38˚C for cold water use only
32˚F / 0˚C for cold water use only
1/4” NPTF x 1/4” tube
1/4” NPTF x 1/4” tube sub micron (0.5 micron)
NSF International , CA Dept. of Public Health : Cert: #13-2190
Notes
1. The Stream Flow Plus Drinking Water System is installed below the sink and connects to a separate faucet included in the installation materials.
2. Replacement filters can be purchased at StreamFilters.com.
Filter life will vary in proportion to the amount of water used and the level of impurities in the water being processed.
Replace the filter cartridge when the first of the following occurs:
(a) annually; (b) when the system’s rated capacity is reached;
(c) the flow rate diminishes; or (d) the filter becomes saturated with bad tastes and odors. The rated capacity of the filter cartridges is shown above.
3. This system is not intended to be used where the water is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the unit. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
4. Do not allow water to freeze in the unit. If unit is exposed to freezing temperatures, drain water from unit and remove filter.
5. Do not allow water to sit in unit for extended periods of time
(10 or more days) without being used. If unit is to be left unused for more than 10 days, drain all water from the system and remove the filter. Upon your return, reconnect the filter in the housing and continue use. In the event water does sit in the unit for 10 or more days, the system should be flushed by allowing water to flow to waste for about 3 minutes; then continue use as normal.
6. To dispose of the used filter, remove it from the housing and place the old filter in your normal refuse.
General Information
3
Sec.
01
B. Installation Overview & Parts
1
6
3
2
5
7
8
4
4
5
6
7
8
1
2
3
Faucet Assembly (with blue tubing attached*)
Wing Nut
Blue Tubing (connects outlet adapter to plumbing)
Clear Tubing (connects inlet adapter to plumbing)
Inlet and Outlet Adapters
Housing Top
Black Rubber Cushion (inside housing top)
Carbon Block Filter
9
10
V-band Knob
V-band
11
12
13
O-ring
Wall Bracket
Housing Bottom
14 Acrylic Sleeve
9
10
11
12
13
14
Stream Drinking Water Systems have been tested and certified, so you know that they will perform at the highest level possible. Please read this manual before installing your Stream Flow Plus System, as installation, operation, and maintenance will aid in your System’s performance. Not following these instructions carefully could lead to product failure or possible damage.
If you need help or assistance, contact us at StreamFilters.com or (888) 615-5733.
*Faucet is not included as part of the NSF Unit Certification
4
General Information
Preparing the Housing
Please prepare the housing as outlined in this section before moving on to Section 3. Be sure to gather all all recommended tools for the Stream Flow Plus below the sink installation before you begin.
Sec.
02
A. Filter Cartridge Installation
Top
V-band
Bottom
Turn to connect
The filter cartridge is shipped outside of the unit housing
(in most cases) to protect your filter and drinking water system from damage during shipping. Be sure to insert the filter cartridge into the drinking water system housing before proceeding with the installation.
First, remove the plastic wrapper and instruction wrap from around the filter.
1. With the housing positioned upright, open the unit by unscrewing the black knob on the locking v-band. Spread it apart and remove the v-band.
2. Separate the unit, leaving the black rubber o-ring in place on the housing.
3. . Screw the new filter (cartridge) in the housing top, turning it until firm. Filter needs to make 4-5 complete revolutions in order to ensure a firm seal. Be sure that the filter has been screwed in straight. DO NOT OVER TIGHTEN.
4. Reconnect the housing top with bottom and replace locking v-band; replace black knob and turn until tight. Be sure that the locking v-band is fastened tightly by: a. Checking the v-band to confirm that it is secured evenly around the housing top and bottom.
b. Hand-tightening the black knob on the v-band until it is as tight as possible.
Preparing the Housing
5
Sec.
03
Below the Sink Installation
A. Required Tool List
The following tools are required to install Stream Flow Plus Drinking Water System below the sink:
Installation of Faucet/Spigot
(Stainless Steel Sink):
• 3/8” Reversible electric drill
• 7/16” High speed steel drill bit
• Hammer
• Center punch
• 8” Adjustable wrench
• Pliers or vise grips
• 1/8” High speed drill bit
Adapt-a-Valve Installation:
• 8” Adjustable wrench
• Wire cutter or knife
Installation of Faucet/Spigot
(Ceramic/Porcelain Sink):
• 3/8” Reversible electric drill
• 7/16” High speed steel drill bit
• Hammer
• Center punch
• 8” Adjustable wrench
• Pliers or vise grips
B. Attaching the Adapters to the Housing
Stream Flow Plus models are shipped with all of the adapters and connectors needed for the filter system.
Here is how to connect them to the housing top:
To Connect Straight Adapters:
1. Connect the 1/4” outlet adapter to the outlet opening on the housing by turning it clockwise. You can tighten it by hand and then give it one to two more turns with a wrench.
2. Connect the 1/4” inlet adapter to the inlet opening on the housing by turning it clockwise. Again, tighten it by hand and then with a wrench.
6
Below the Sink Installation
C. Housing Assembly
Outlet Connector
Inlet Connector
Housing Top
Below Sink Installation Includes:
a
*
b
Rubber Cushion
V-Band a.
Stainless Steel
Faucet with blue
tubing attached b.
1/4” Inlet and
Outlet Connector
Filter
O-Ring
Wall Bracket
Adapt-a-Valve Assembly:
a b
Housing Bottom a.
Adapt-a-Valve b.
Threading
Adapter
Acrylic Sleeve
*Faucet is not included as part of the NSF Unit Certification
Below the Sink Installation
7
Sec.
04
Installing the Faucet
A. Drill the Hole or Use Existing Hole
Porcelain or Ceramic Surface
1. Choose and then mark the spot you’d like to mount the faucet on your sink top.
a. Make sure there aren’t any reinforcing ribs under the spot you’ve selected.
b. If you have an extra hole in your sink for a spray hose, you can disconnect that hose and use its hole for your drinking water faucet.
2. Make an indentation with the center punch by tapping gently with the hammer on the ceramic/porcelain where the hole will be drilled.
3. Use the 1/2” carbide tipped masonry drill bit to grind the porcelain down to the metal so that you won’t damage the porcelain when drilling.
4. Carefully use the 7/16” high speed steel drill bit to completely drill a hole through the metal sink. Make sure you don’t let the drill bit
“grab” the porcelain.
Stainless Steel or Metal Surface
Here you can simply follow the same first two steps listed above, then:
1. Use the 1/8” high speed steel drill bit to drill a pilot hole.
2. Use the 7/16” high speed steel drill bit to completely drill a hole through the stainless steel sink.
8
Installing the Faucet
B. Mounting the Faucet
*
Cover Plate
Small Black Washer
Large Black Washer
Counter top
Plastic Washer
Wing Nut
Lock Washer
Blue Tubing
1. Make sure the blue tubing is attached to the faucet.
2. From the sink/counter top, place the following over the faucet hole:
a. The larger soft black rubber washer
b. The cover plate
c. The smaller soft black rubber washer
d. The faucet with blue tubing attached
3. From under the sink, slide over the blue tubing:
a. The hard black plastic washer (with the small side up)
b. The lock washer
c. The wing nut
4. Hand tighten the wing nut to secure the faucet. Using vice grips, secure the wing nut and faucet below the sink.
*Faucet is not included as part of the NSF Unit Certification
Installing the Faucet
9
Sec.
05
Connect to Plumbing
The Adapt-a-Valve assembly includes an Adapt-a-Valve and adapter.
NOTE: When attaching the Adapt-a-Valve to straight pipe threads, use Teflon tape on the threads.
Wrap the tape around the pipe only once.
Before Included
1 2
Water supply line before installation
After
Choose the configuration (3/8” or 1/2”) that fits your plumbing.
A. Use the 3/8” configuration on a water supply line with a 3/8” slip joint.
A
Water supply line with Adapt-a-Valve in 3/8” configuration
10 Connect to Plumbing
B. Use the 1/2” configuration if you have a water supply line that either does not have a slip joint nut, or has a 1/2” slip joint nut at the angle stop valve.
B
Water supply line with Adapt-a-Valve in 1/2” configuration
Install on the cold water line only:
1. Turn the angle stop valve completely off to turn off the cold water supply.
2. Turn the slip joint nut counter clockwise with an 8” adjustable wrench to disconnect the cold water supply line. This will either be located at the angle stop valve or at your faucet pipe, depending on your plumbing.
3. With your wrench, connect the Adapta-a-Valve to the pipe where you removed the slip joint nut.
Make sure the rubber washer is in place, and then turn it clockwise until it is tight, but not over-tight!
4. Connect the plumbing/supply line to the Adapta-a-Valve with the slip joint nut. If necessary, you can trim the supply line before connecting to make sure the supply line doesn’t block the shut-off valve on the side.
5. Connect your 1/4” clear plastic tubing to the Adapta-a-Valve by inserting the tubing as far as it will go, through the same small hole in the adapter that you attached to the shut-off valve.
a. Cut (square cut) the tip ends off the tubing using a sharp knife. Do not use scissors.
b. Push the tubing through the small hole in the valve until you feel resistance—at this point, the tubing is still not fully inserted, so you’ll need to push firmly until the tubing is inserted as far as it will go. Ultimately, the 1/4” clear tubing should be inserted about 5/8”.
6. Make sure that the unit shut-off valve, attached to the Adapta-a-Valve, is off by turning the handle clockwise until it stops.
Connect to Plumbing
11
Sec.
06
Connect The Drinking Water System
Now that you have installed the filter, adapters, and faucet and connected the device to the plumbing you are ready to complete the installation of your Stream Flow Plus Drinking Water System.
A. Adapter Connection
If you have not already installed the adapters, see Section 3B on page 6.
B. Tubing Connection
Be sure to provide sufficient tubing for conveniently changing the filter when it is time to replace it.
1. Using wire cutters or a knife, cut the tips off of both the blue tube connected to the faucet and the clear tube you previously connected to the plumbing.
2. Insert the clear 1/4” plumbing tubing into the small hole in the inlet connector as far as it will go. Ultimately this 1/4” tubing should be inserted about 5/8”. Then pull to make sure that the tubing is secure.
Disconnecting the tubing: If you ever need to disconnect the tubing for maintenance, you should first make sure that the system is depressurized.
Push the collar against the face of the fitting; then you can remove the tubing.
C. Ice Maker Connection
Not only can you use your Stream Flow Plus Drinking Water System for quality water at the sink, but you can also connect that same unit to your refrigerator for quality ice. Here’s how:
Connecting to Your Unit:
1. Determine whether or not you have access to your refrigerator from your sink.
2. Cut 3” from the end of the blue faucet tubing.
3. Insert the tubing still connected to the faucet into the top of the ice maker tee. Make sure you insert the tubing all the way—even past the point of resistance, and then pull to make sure it is secure.
(Ultimately it should be inserted about 5/8”.)
4. Insert one end of the loose blue tubing into the bottom port of the icemaker tee. Again, make sure you insert the tubing all the way— even past the point of resistance, and then pull to make sure it is secure. (Ultimately it should be inserted about 5/8”.)
5. Connect the other end of the blue tubing to the outlet connector.
6. Connect a separate 1/4” poly tube (available through your dealer or a plumbing supplier) to the side port of the tee. Make sure you have enough tubing to reach your refrigerator and service unit.
12 Connect The Drinking Water System
D. Placing Stream Flow Plus Under the Sink
You can either set your Stream Flow Plus System on the cabinet floor or mount the unit on the cabinet wall with the bracket included in your kit. If you do mount the unit on the cabinet wall, make sure it can support the unit’s weight (about 7.5 with a dry filter and even more with a wet filter!).
Either way, be sure to provide enough tubing to conveniently change the filter when you need to.
1. Make sure you’ll have enough room to remove the stainless steel housing from the bracket to change the filter in the future, before beginning installation.
2. Position the bracket so that you will be able to get to it when needed. Hold the bracket in place and then fasten it there with only the top screws. (Don’t fasten the screws tight against the bracket—leave enough space to hang and later remove the bracket from the screws.)
3. Remove the bracket from the screws by lifting it straight up.
4. To install the bracket bands with worm screws, first unscrew the worm clamp by turning the screw with a slotted screwdriver counter clockwise until it is fully open.
5. Thread each band through the two slots on the bracket
(there will be one for the top and one for the bottom slot).
6. Install the bands around the housing top, above the v-band.
Position the slotted end of the band at the mouth of the worm clamp opening. Then turn the screw of the worm clamp clockwise; as you turn the screw, the band will close around the housing top until it is secured tightly. Repeat for the second band.
7. Attach the bracket and unit to the wall by “hanging” the bracket on the two screws you installed (Step 2).
Connect The Drinking Water System
13
Sec.
08
Start-up and Use
1. Dry off all the plumbing connections and the drinking water unit.
2. Make sure all of the connections are tight, but not over tight.
3. Turn on the shut-off valve under your sink where water enters your residence.
4. Turn the handle on the shut-off valve that you’ve installed (see Section 5) to turn on the water to your Drinking Water System.
5. Turn the operating lever to open the drinking water faucet.
6. Let the water run through the unit and faucet for about 10 minutes so that all air can escape.
7. Adjust the handle on the shut-off valve so that the water flow will be minimal (To be precise, it should not exceed 1.0 gpm. It takes about 15 seconds to fill a quart at 1.0 gallon per minute.)
8. Close the drinking water faucet and check for leaks.
a. Check the v-band to confirm that it is secured evenly around the housing top and bottom.
b. Hand-tighten the black knob on the v-band until it is as tight as possible.
9. Let the water run through the unit for about 30 minutes to flush any loose carbon fines.
10. Shut off the water and check for leaks.
The Stream Flow Plus Drinking Water System is now ready for use. You can enjoy having great tasting, high quality water for drinking, cooking, beverages, food preparation, and more.
A. Filter Life
Filter life will vary depending on the amount of water used and the amount of impurities being processed in your water. If your Stream Flow Plus clogs, it may be because it is protecting you from the contaminants and physical matter in your drinking water. If this happens, see Section I.A -
Operation and Maintenance Specifications.
For the best performance possible and to maintain your warranty, you should replace your filter when the first of the following occurs: (a) annually; (b) when you’ve reached the unit’s rated capacity;
(c) the flow rate slows or lessens; or (d) the filter starts to taste or smell bad.
14 Start-Up and Use
Performance Certification
MODEL - FP1
Stream Drinking Water Systems Product Performance Tested and Certified
Stream Drinking Water System Tested and Certified by NSF International to NSF/ANSI
Standards 42 and 53 for the reduction of claims specified below.
Standard 42, Aesthetic Effects Standard 53, Health Effects
• Chloramine
• Chlorine taste and odor
• Nominal Particulate Reduction,
Class I
• Asbestos
• Chlordane
• Cyst
• Lead
• Mercury
• MTBE
• PCB
• Toxaphene
• Turbidity
• VOC (listed below)
Sec.
08
Volatile Organic Chemicals (VOC) include:
Disinfection By-Products
• chloropicrin
• haloacetonitriles (HAN):
- bromochloroacetonitrile
- dibromoacetonitrile
- dichloroacetonitrile
- trichloroacetonitrile
• haloketones (HK):
- 1,1-dichloro-2-Propanone
- 1,1-trichloro-2-Propanone
• trihalomethanes (THMs; TTHMs):
- bromodichloromethane
- bromoform
- chloroform
- dibromochloromethane
• tribromoacetic acid
Pesticides
• carbofuran
• dibromochloropropane (DBCP)
• o-dichlorobenzene
• p-dichlorobenzene
• endrin
• ethylene dibromide (EDB)
• heptachlor
• heptachlor epoxide
• lindane
• methoxychlor
Herbicides
• alachlor
• atrazine
• 2,4-D
• dinoseb
• pentachlorophenol
• 2,4,5-TP (silvex)
Chemicals
• benzene
• carbon tetrachloride
• chlorobenzene
• 1,2-dichloroethane
• 1,1-dichloroethylene
• cis-1,2-dichloroethylene
• 1,2-dichloropropane
• cis-1,3-dichloropropylene
• ethylbenzene
• hexachlorobutadiene
• hexachlorocyclopentadiene
• simazine
• styrene
• 1,1,2,2-tetrachloroethane
• tetrachloroethylene
• toluene
• trans-1,2-dichloroethylene
• 1,2,4-trichlorobenzene
• 1,1,1-trichloroethane
• 1,1,2-trichloroethane
• trichloroethylene
• xylenes (total)
Performance Certification
15
Sec.
09
Performance Data Sheets
MODEL - FP1
Substance
Stream Drinking Water Systems have been tested according to NSF/ANSI Standard No. 53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 53
Health Effects.
Percent
Reduction
Influence
Challenge
Concentration
Maximum permissible product water concentration
ALACHLOR*
ASBESTOS*
ATRAZINE*
BENZENE*
BROMODICHLOROMETHANE (TTHM)*
BROMOFORM (TTHM)*
CARBOFURAN (Furadan)*
CARBON TETRACHLORIDE*
CHLORDANE
CHLOROBENZENE (Monochlorobenzene)
CHLOROPICRIN*
CHLOROFORM (TTHM)* (surrogate chemical)
Cryptosporidium (CYST)
CYST (Giardia; Cryptospordium; Entamoeba;
Toxoplasma)
2, 4-D*
DBCP (see Dibromochloropropane)*
1, 2-DCA (see 1, 2-DICHLOROETHANE)*
1, 1-DCE (see 1, 1-DICHLOROETHYLENE)*
DIBROMOCHLOROMETHANE (TTHM;
Chlorodibromomrthane)*
DIBROMOCHLOROPROPANE (DBCP)* o-DICHLOROBENZENE (1, 2 Dichlorobenzene)* p-DICHLOROBENZENE (para-Dichlorobenzene)*
1, 2-DICHLOROETHANE (1, 2-DCA)*
1, 1-DICHLOROETHYLENE (1, 2-DCE)*
CIS-1, 2-DICHLOROETHYLENE*
TRANS-1, 2-DICHLOROETHYLENE*
1, 2-DICHLOROPROPANE (Propylene Dichloride)*
CIS-1, 3-DICHLOROPROPYLENE*
DINOSEB*
EDB (see ETHYLENE DIBROMIDE)*
ENDRIN*
Entamoeba (see CYSTS)
ETHYLBENZENE*
ETHYLENE DIBROMIDE (EDB)*
Furadan (see CARBOFURAN)*
Giardia Lamblia (see CYST)
>98%
>99%
>97%
>99%
>99.8%
>99.8%
>99%
98%
>99.4%
>99%
99%
>99.8%
99.95%
99.95%
98%
>99%
95%
>99%
>99.8%
>99%
>99%
>98%
95%
>99%
>99%
>99%
>99%
>99%
99%
>99%
99%
99.95%
>99%
>99%
>99%
>99.95%
0.05
10
0.1
7
0.081
0.3
0.3
0.17
0.17
0.19
to 10
0.19
0.078
0.077
0.015
0.110
0.052
0.088
0.083
0.300
0.052
0.08
0.04
0.088
0.083
0.086
0.08
0.079
0.044
0.053
0.088
0.044
8 fibers/L
0.04 +/- 10%
0..300 +/- .30
minimum 50,000/ml minimum 50,000/ml minimum 50,000/ml minimum 50,000/ml
0.001
99% reduction requirement
0.003
0.001
0.015
0.015
0.001
0.0018
0.002
0.001
0.0002
0.015
99.95%
99.95%
0.0017
0.00002
0.0048
0.001
0.015
0.00002
0.001
0.001
0.0048
0.001
0.0005
0.001
0.001
0.001
0.0002
0.00002
0.00059
99.95%
0.001
0.00002
0.001
99.95%
** Percent reduction reflects actual performance of Stream product as specifically tested (at 200% of capacity). Percent reduction shown for VOCs* reflects the allowable claims for volatile organic chemicals/compounds as per tables. Chloroform was used as a surrogate for VOC reduction claims; the Stream Systems actual reduction rate of chloroform was >99.8% as tested.
16 Performance Data Sheets
MODEL - FP1
HALOACETONITRILES (HAN)*:
BROMOCHLOROACETONITRILE
DIBROMOACETONITRILE
DICHLOROACETONITRILE
TRICHLOROACETONITRILE
HALOKETONES (HK)*:
1, 1-DICHLORO-2-PROPANONE
1, 1, 1-TRICHLORO-2-PROPANONE
HEPTACHLOR*
HEPTACHLOREPOXIDE*
HEXACHLOROBUTADIENE (Perchlorobutadiene)*
HEXACHLOROCYCLOPENTADIENE*
LEAD (pH 6.5)
LEAD (pH 8.5)
LINDANE*
MERCURY (pH 6.5)
MERCURY (pH 8.5)
METHOXYCHLOR*
Methylbenzene (see TOLUENE)*
Monochlorobenzene (see CHLOROBENZENE)*
MTBE (methyl tert-butyl ether)
POLYCHLORINATED BIPHENYLS (PCB, Aroclor 1260)
PCE (see TETRACHLOROETHYLENE)*
PENTACHLOROPHENOL*
Perchlorobutadiene (see HEXACHLOROBUTADIENE)*
Propylene Dichloride (see 1, 2-DICHLOROPROPANE)*
SIMAZINE*
Silvex (see 2, 4, 5-TP)*
STYRENE (Vinylbenzene)*
1, 1, 1-TCA (see 1, 1, 1-TRICHLOROETHANE)*
TCE (see TRICHLOROETHYLENE)*
1, 1, 2, 2-TETRACHLOROETHANE*
TETRACHLOROETHYLENE*
TOLUENE (Methylbenzene)*
TOXAPHENE
Toxoplasma (see CYSTS)
2, 4, 5-TP (Silvex)*
TRIBROMOACETIC ACID*
1, 2, 4 TRICHLOROBENZENE*
1, 1, 1-TRICHLOROETHANE (1 ,1, 1-TCA)*
1, 1, 2-TRICHLOROETHANE*
TRICHLOROETHYLENE (TCE)*
TRIHALOMETHANES (TTHM) (Chloroform; bromoform; bromodichloromethane; dibromochloromethane)
TURBIDITY
Unsym-Trichlorobenzene*
Vinylbenzene (see STYRENE)*
XYLENES (TOTAL)*
98%
98%
98%
98%
96.6%
97.2%
>99%
>99%
>98%
>99%
>97%
99%
>99%
95%
>99%
>99%
>99%
>99%
>92.9%
99.95%
99%
99%
96%
>99%
98%
>98%
>99%
>99.3%
>99.3%
>99%
96.6%
96.8%
>99%
>99%
>99%
>99%
95%
>99%
>99%
>99.8%
98.8%
>99%
>99%
>99%
0.022
0.024
0.0096
0.015
0.0072
0.0082
0.025
0.0107
0.044
0.060
0.15 +/- 10%
0.15 +/- 10%
0.055
0.006 +/- 10%
0.006 +/- 10%
0.050
0.078
0.077
0.015 +/- 20%
0.01 +/- 10%
0.081
0.096
0.044
0.080
0.120
0.270
0.15
0.084
0.180
0.081
0.081
0.078
0.015 +/- 10% minimum 50,000/ml
0.270
0.042
0.160
0.084
0.150
0.180
0.300 +/- .30
11 +/- 1 NTU
0.160
0.150
0.070
0.0005
0.0006
0.0002
0.0003
0.5 NTU
0.0005
0.0005
0.001
Note: This addresses the U.S. Environmental Protection Agency (USEPA) Primary and Secondary Drinking Water Regulations in effect at its time of publication, as they relate to Stream’s performance in conformance to the industry performance criteria. These regulations are continually being updated at the Federal level. Accordingly, this list of MCLs will be reviewed and amended when appropriate.
Performance Data Sheets
17
0.0016
0.0005
0.0046
0.0010
0.001
0.001
0.001
0.003
99.95%
0.0016
0.001
0.0005
0.0046
0.0005
0.0010
0.0001
0.0003
0.00001
0.0002
0.001
0.000002
0.010
0.010
0.00001
0.002
0.002
0.0001
0.001
0.001
0.005
0.0005
0.001
0.001
0.001
0.001
0.004
0.015
A. NSF/ANSI 42 - AESTHETIC EFFECTS
The system has been tested according to NSF/ANSI 42 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42.
CHLORAMINE as Aesthetic Effect (As Monochloramine)
CHLORINE as Aesthetic Effect
PARTICULATE, (Normal Particulate Reduction, Class I,
Particles 0.5 TO <1 UM
>97%
>97%
Class I >99%
3.0 mg/L +/- 10%
2.0 mg/L +/- 10%
At Least 10,000 particles/mL
0.5 mg/L
> or = 75%*
> or = 85%*
1. Stream Drinking Water Systems have been certified by NSF International for compliance to NSF/ANSI
Standard Nos. 42 and 53. Stream Drinking Water Systems have been certified by the State of California
Department of Public Health for the reduction of specific contaminants listed herein.
2. Chloroform was used as a substitute for claims of reduction of VOCs, where the Stream System’s actual reduction rate of chloroform was greater than 99.8% when tested at 200% capacity.
3. Do not use with water that is microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
4. Stream’s housing is warranted for a lifetime (with annual cleaning); all exterior hoses and attachments to the System are warranted for one year. Please see the owner’s manual for complete product guarantee and warranty information.
5. Please see the Owner’s Manual for installation and operating procedures.
6. In compliance with New York law, New York residents should have their water supply tested to determine their actual water treatment needs before purchasing a water treatment system. Please compare the capabilities of the Stream unit with your actual water treatment needs.
7. While testing was performed under standard laboratory conditions, actual performance may vary.
8. The list of substances that this device reduces does not necessarily mean that they are present in your tap water.
B. Operational Specifications
Model Number:
Replacement Filter Type:
Approximate Filter Capacity:
Approximate Flow Rate at 60 psi:
Maximum Working Pressure:
Minimum Working Pressure:
Maximum Operating Temperature:
Minimum Operating Temperature:
Stream Flow Plus (FP1)
Stream Flow Cartridge (FC1)
750 gallons
0.75 gpm
100 psi / 8.8 kg/cm
2
30 psi / 2.1 kg/cm
2
100˚F / 38˚C for cold water use only
32˚F / 0˚C for cold water use only
18 Performance Data Sheets
C. California Certification Department of Public Health
California Department of Public Health Certification Number #13-2190. For conditions of use, health claims certified by the CA Department of Public Health, and replacement parts, see Product Data
Sheet / Owner’s Manual.
State of California Department of Public Health
Water Treatment Device
Certificate Number
Trademark/Model Designation
Stream Flow FL
Stream Flow Plus FPL
Manufacturer: Stream Laboratories, Inc.
13-2190
Date Issued: October 3, 2013
Replacement Elements
FC1
FC1
The water treatment device(s) listed on this certificate have met the testing requirements pursuant to
Section 116830 of the Health and Safety Code for the following health related contaminants:
Microbiological Contaminants and Turbidity
Cysts
Turbidity
Organic Contaminants
Atrazine
Benzene
Carbofuran
Carbon Tetrachloride
Chlorobenzene
Chloropicrin
2,4-D
DBCP o-Dichlorobenzene p-Dichlorobenzene
1,2-Dichloroethane
1,1-Dichloroethylene cis-1,2-Dichloroethylene trans-1,2-Dichloroethylene
1,2-Dichloropropane cis-1,3-Dichloropropylene
Dinoseb
Endrin
Lindane
Ethylbenzene
EDB
Haloacetonitriles
Bromochloroacetonitrile
Dichloroacetonitrile
Dibromoacetonitrile
Trichloroacetonitrile
Haloketones (HK)
1,1-Dichloro-2-Propanone
1,1,1-Trichloro-2-Propanone
Heptachlor
Heptachlor Epoxide
Hexachlorobutadiene
Hexachlorocyclopentadiene
Lindane
Methoxychlor
MTBE
Pentachlorophenol
PCB
Simazine
Styrene
1,1,2,2-Tetrachlorethane
Tetrachloroethylene
Toluene
Toxaphene
2,4,5-TP (Silvex)
Tribromoacetic Acid
1,2,4-Trichlorobenzene
1,1,1-Trichloroethane
1,1,2-Trichloroethane
Trichloroethylene
Trihalomethanes (THM’s)
Bromodochloromethane
Bromoform
Chloroform
Chlorodibromomethane
Xylenes
Rated Service Capacity: 750 gallons Rated Service Flow: 0.75 gpm
Conditions of Certification
Inorganic/Radiological Contaminants
Asbestos
Lead
Mercury
Do not use where water is microbiologically unsafe or with water of unknown quality, except that systems for cyst reduction may be used on disinfected waters that contain filterable cysts.
Stream Laboratories, Inc.
2520 Shell Road Ste B
Georgetown, TX 78628
Phone: (888)-615-5733
StreamFilters.com
Performance Data Sheets
19
Sec.
10
Troubleshooting & FAQs
A. Troubleshooting & FAQs
Question
When should I replace my filter cartridge?
Answer
You should replace your filter annually or when the capacity is reached, whichever occurs first (for rated capacity see
Section 1A).
Where do I get a replacement filter?
You can order replacement filters from your local water treatment dealer.
Comments
Filter life will vary depending on the amount of water used and the amount of impurities in the water.
N/A
Will low pH or acidic water affect the
Stream filter?
No
.
Mineral components expressed as acidity and alkalinity determines the pH.
Neutrality is 7; below 7 is acidity; and above 7 is alkalinity.
N/A
Does de-ionized water or soft water affect Stream water?
Can the Stream Flow Plus System be connected to an automatic ice maker?
What causes “white” particles to appear in Stream water when it is frozen or boiled?
No.
Yes, the below sink models can be connected to your sink, refrigerator, and/or any kind of water dispenser or ice maker.
To connect a single Drinking Water System to both your sink and refrigerator, request an “ice maker tee” from your dealer.
Can the Stream Flow Plus System be used during an emergency or when the water is turned off?
Yes, you can hand pump or siphon water through the Stream System during an emergency. But remember, the Stream
System isn’t meant to be used where the water is microbiologically unsafe or with water of unknown quality.
When water is frozen, the natural minerals solidify and they can appear as white flakes or specks when the ice melts.
If your water source might be contaminated, it should be disinfected before use. Add 1/4 tsp of household bleach per gallon of water; the Stream
System will remove this solution from the water. Hand pump kits are available from Stream.
Natural minerals are good for you in normal quantities, and so when you see them in your drinking water, don’t be alarmed.
Why does the Stream System reduce volatile organic compounds, but not natural minerals?
Minerals are totally dissolved in the solution and do not have an actual physical size, and so the minerals pass through the filter unchanged.
The materials used in Stream Drinking
Water Systems are specially designed to react with chemicals in the water, but not with natural minerals that are actually good for you.
Should I remove sediment with a standard filter before using Stream?
If you are in an area with excessive sedimentation in the water, pre-filtering can help extend the life and efficiency of your Stream cartridge, but in most areas this is not necessary.
The Stream System contains a triple filter. The outside material is a pre-filter that helps protect the solid carbon block surface from clogging with large sediment.
Why is the compressed activated carbon block filtration system more efficient than loose granular systems?
Stream’s solid carbon block filters are compacted into a dense structure so that every molecule of water will be forced through tiny pores of carbon. This reduces a wide range of hazardous contaminants, as well as tastes and odors, not typically removed by loose granular systems.
The Water Quality Association reports that “an activated carbon filter can reduce organics and solid particles, as well as offensive tastes and odors. Only pre-coat and solid carbon block filters are designed to provide 0.5 micron mechanical filtration with efficient adsorption on very fine sized activated carbon particles.”
20 Troubleshooting & FAQs
Troubleshooting & FAQs
Question
What is the difference between a
“water softener” and the Stream Drinking
Water System?
Answer
Softeners are not used to treat drinking water; they are used only to change the water’s “hardness.” They put sodium into the water in exchange for magnesium or calcium ions. Stream Drinking Water
Systems don’t remove dissolved minerals so the pH is not changed.
Can the Stream System be used on untreated water?
Comments
Soft water is good for bathing, laundering, and may extend the life of hot water heaters and boilers. However, soft water should not be used for watering plants or lawns. You should not use a water softener for drinking water.
If the water source is questionable, you should disinfect it before use. Just add 1/2 tsp of bleach per gallon of water; then the
Stream System will remove this solution from the water. Ask your nearest public water utility for assistance or guidelines on the proper treatment of untreated water.
Stream Systems are designed to be used on treated water systems; they are not meant to be used where the water is unsafe or with water of unknown quality without first disinfecting the water.
However, systems certified for cyst reduction can be used on water that may contain filterable cysts.
What should I do if my water starts to smell or taste bad?
Change your filter. The carbon block filter may adopt the tastes and odors that it is absorbing.
What does it mean if my water starts to smell like rotten eggs?
What does it mean if there is a “milky” color in my water?
This is typically a sign of hydrogen sulfide gas, which is not uncommon and can occur at any time.
You should keep 2 filters on hand. When one begins to smell, remove it and let it dry upside down on a paper towel. Once the sulfur smell dissipates, you can reuse the filter. Rotating filter cartridges like this will also help extend the life of your filters.
This milky color is actually just small bubbles, caused by a higher than normal water pressure flowing through the system. This won’t affect the performance of the System.
Just reduce the water pressure at the feed water adapter below the sink.
What do I do if the flow rate is too slow?
What should I do if my water is black?
The filter is designed to slow and restrict flow when the filter is clogged with contaminants. When the flow rate slows, it is time to change your filter.
You should replace your filters at least every twelve months, or when its capacity is reached, whichever comes first. You can also try turning up the water pressure or turning off other faucets or sprinklers that may be on.
Allow the water to run through the unit for about 30 minutes.
The black color is from carbon dust and is nothing to worry about.
Simply flush the system.
Troubleshooting & FAQs
21
B. Maintenance Problems
Flushing/Disinfecting the Unit Housing:
You should not let water sit for more than 10 days without being used. If you do, the System may need to be flushed or disinfected before you start using it again.
1. Make sure the water to the unit is turned off.
2. Lessen the water pressure (if below sink unit) by opening the unit faucet.
3. Remove and throw out the used filter.
4. Rinse out the inside of the unit’s housing.
5. Add 5 to 7 drops of bleach, like Clorox™ or Purex™, to the bottom canister.
6. Reconnect the housing top and bottom without the replacement filter.
7. Turn on the water and let the unit housing fill up with the water/bleach solution.
8. Let the unit soak for at least 30 minutes.
a. To disinfect the spout, remove it and put it in a container with 1 quart of water and 5 drops of bleach. Allow this to soak for 30 minutes.
9. After the housing has soaked for 30 minutes, disassemble the top and bottom and pour out the water/bleach solution; then rinse out the inside of the housing.
10. Replace the filter (cartridge).
11. Once the new filter is installed, follow the instructions to reconnect and flush your unit.
22 Troubleshooting & FAQs
Warranty
Stream believes in improving your water and your life, which is why we’ve tailored our warranty for you— to make your life just a little bit easier.
Stream will repair or replace any System at absolutely no charge (baring the transportation to Stream headquarters) during the warranty period. On top of that, all exterior hoses and attachments to the
System are warranted for defects in material and workmanship for one year, and your Drinking Water
System Housing is warranted for a lifetime, while you’re changing the filter once a year. That’s a lifetime of clean water.
The Stream solid carbon block filters are warranted for defects in material and workmanship under normal care.
Unless it is expressly stated above, Stream Corporation makes no warranties, expressed or implied, arising by law or otherwise. This includes the implied warranties of merchantability and fitness for a particular purpose, to any person. This limited warranty may not be changed or extended unless it is expressly executed by Stream Corporation. The repair or replacement as provided under this limited warranty is exclusive. In no event will Stream Corporation be liable for any consequential or incidental damages to any person, including in cases of manufacturer negligence. This includes, without limitation, damages of loss of use, cost of substitution, property damage, or other monetary loss.
The warranty is only valid if the Drinking Water System is operated within conditions listed herein.
Stream Laboratories, Inc.
2520 Shell Road Ste B
Georgetown, TX 78628
Phone: (888)-615-5733
StreamFilters.com

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Removes contaminants and bad tastes and odors
- Easy to install and maintain
- Connects to sink or refrigerator
- Certified by NSF International and CA Dept. of Public Health
- 750 gallons filter capacity