User Manual
User Manual
PVS7989
8 in. Dual Screen Mobile DVD Player
Safety Precautions
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DO NOT PLACE OBJECTS
FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.
The lightning flash with an arrowhead
CAUTION
symbol, within the equilateral triangle, is
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
intended to alert the user to the presence
of
uninsulated
“dangerous
voltage”
within the product’s enclosure that may
be of sufficient magnitude to cause an
electric shock.
PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE.
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO
The
exclamation
point
within
the
WIDE SLOT OF POWER OUTLET, THEN FULLY INSERT.
equilateral triangle is intended to alert
THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADIAN
the user to the presence of important
ICES-003.
operating and maintenance (servicing)
instructions in this owner’s manual.
* SEE BOTTOM OF UNIT FOR GRAPHIC
SYMBOLS*
CAUTION
INVISIBLE LASER RADIATION WHEN
This product contains a
low power laser device.
OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
On Placement
•
•
Do not use the unit in places that are extremely hot, cold, dusty, or humid, use it in moderate climates.
Do not restrict the ventilation openings of the unit by covering it with items such as newspaper, tablecloths,
curtains, etc.
On Safety
•
When connecting or disconnecting the AC adapter, grip the plug and not the cord itself. Pulling the cord may
damage it and create a hazard.
•
When you are not going to use the unit for a long period of time, disconnect the AC adapter.
•
No un-covered flame sources such as lighted candles should be placed on the AC adapter or the unit.
On Condensation
•
When left in a heated room where it is warm and damp, water droplets or condensation may form inside the
unit. When there is condensation inside the unit, the unit may not function normally. Let the unit stand for 1 to
2 hours before turning the power on, or gradually heat the room and let the unit dry before use.
Rating Plate Location
•
The rating plate is located on the bottom of unit.
FCC Statements
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
GB - 1
Safety Precautions
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
•
Should any trouble occur, disconnect the AC adapter and refer servicing to a qualified
technician.
•
•
WARNING
No objects filled with liquids, such as vases, shall be placed on the unit.
The AC adapter is used as the disconnect device and it shall remain readily operable and should
not be obstructed during intended use. In order to disconnect the apparatus from the supply
mains, the AC adapter should be disconnected from the mains socket outlet.
Notes on Copyright
It is forbidden by law to copy, broadcast, show, broadcast on cable, play in public, or rent copyrighted material
without permission.
Apparatus Claims of U.S. Patent Nos. 6,836,549; 6,381,747; 7,050,698; 6,516,132; and 5,583,936 licensed for limited
viewing uses only.
This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual
property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering
or disassembly is prohibited.
Important Safety Instructions
1.Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. When the provided plug does not fit into your AC power
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the AC power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the apparatus. When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13.Unplug this apparatus during lightning storms or when unused for long periods of
Portable Cart Warning
time.
14.Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as the AC power cord or plug is damaged, liquid has spilled or
objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
GB - 2
Table of Contents
Safety Precautions...................................... 1
locating a desired section....................17
Locating a Specific Title.........................................................17
Important Safety
Locating a Specific Chapter..................................................17
Instructions..................................................... 2
Locating a Specific Time........................................................17
Table of Contents.......................................... 3
DVD PROGRAMMABLE MEMORY................18
DISC FORMATS..................................................... 4
Repeat PLAYBACK ...........................................18
Repeating a Chapter/Title ...................................................18
ACCESSORIES........................................................ 5
Repeating a Single Track/ Whole Disc..............................18
Repeating a Specific Section...............................................18
Using the Remote Control....................... 5
control reference guide.......................... 6
Viewing JPG Files ..........................................19
Remote Control.......................................................................... 6
PLAY ModeS for CD or JPEG
DVD UNIT / MONITOR............................................................... 7
Disc........................................................................19
POWER SUPPLY.................................................... 8
A. Using the AC Power Adapter............................................. 8
B. Using the Car Power Adapter............................................ 9
CUSTOMIZING THE FUNCTION
SETTINGS..............................................................20
Language setup........................................................................20
CONNECtions....................................................10
Video setup................................................................................21
Misc setup...................................................................................21
A. Watching a DVD on the Main Unit and
the Monitor...........................................................................10
B. Connecting a TV (for the Main Unit Only)...................10
MAINTENANCE...................................................22
Cleaning the Disc.....................................................................22
C. Listening a Stereo Receiver or Amplifier
Cleaning the Unit.....................................................................22
on Main unit.........................................................................11
Important Note.........................................................................22
D. Connecting Game Systems/Video Equipment (for
the Monitor Only)...............................................................11
E. Using the Monitor with Other Equipment
Troubleshooting guide...........................22
while Playing DVD on the Main Unit...........................12
F. Using Headphones/Earphones.......................................12
PLACEMENT.........................................................13
A. Mounting in the Vehicle....................................................13
B. Using the Stand....................................................................13
SOUND system................................................14
Unit operation...............................................14
Playing a Disc.................................................15
Playing a Disc.............................................................................15
Pausing Playback (Still Mode)..............................................15
Stopping Playback...................................................................15
Fast Forward / Fast Reverse .................................................15
Skip (Forward / Reverse)........................................................15
Audio Selection........................................................................15
Subtitle Selection.....................................................................16
Angle Selection.........................................................................16
Display Function.......................................................................16
Adjust the LCD Screen............................................................16
GB - 3
DISC FORMATS
This unit can playback discs bearing any of the following marks:
DVDs
[8cm(3")/12cm(5") disc]
Compatible
Audio CDs
[8cm(3")12cm(5") disc]
Region Management Information
Region Management Information: This unit is designed and manufactured to respond to the Region Management
Information that is encoded on DVDs. If the region number printed on the DVD does not correspond to the region
number of this unit, this unit cannot play that disc.
The region number of this unit is 1.
Disc Function or Operation that is Not Available
When the
symbol appears on the TV screen, it indicates that the function or operation attempted is not available
at that time. This occurs because the DVD manufacturer determines the specific functions. Certain functions may
not be available on some discs. Be sure to read the documentation provided with the disc.
Icons Used on DVDs
Language selections for audio
Sample lcons
Language selections for subtitles
Screen aspect ratio
Multiple camera angles
Region code indicator
Note:
•
When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic
images will not be shown.
Title, Chapter and Tracks
•
DVDs are divided into “titles” and “chapters”. If the disc
has more than one movie on it, each movie would be a
separate “title”.“Chapters” are sections of titles.
•
Audio CDs are divided into “tracks”. A “track” is usually
one song on an Audio CD.
Note:
•
Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on them, but
some do not.
Notes on Unauthorized Discs
You may not be able to play back some DVDs on this unit if they were purchased from outside your geographic
area or made for business purposes.
GB - 4
ACCESSORIES
Please check and identify the supplied accessories.
Remote Control (with battery)...................................................................................................................................................... x 1
AC Power Adapter............................................................................................................................................................................. x 1
Car Power Adapter ........................................................................................................................................................................... x 1
DC-AV cable......................................................................................................................................................................................... x 1
Straps..................................................................................................................................................................................................... x 2
remote control
Using the Remote Control
Take out the PVC sheet before operating the
• Point the remote control at the REMOTE SENSOR
Remote Control.
located on the unit.
• When there is a strong ambient light source, the
perform­ance of the infrared REMOTE SENSOR may be
degraded, causing unreliable operation.
• The recommended effective distance for remote
operation is about 16 feet (5 meters).
To Change Remote Battery
2.Insert one CR2025 (3V) size battery.
1.Open the battery door.
BATTERY REPLACEMENT
When battery becomes weak, the operating distance of the Remote Control will greatly reduced and you will need
to replace the battery.
Note:
• If the Remote Control is not to be used for a long time, remove the battery to avoid damage caused by battery
leakage corrosion.
CAUTION
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent
type.
WARNING
Do not dispose of battery in fire, battery may explode or leak.
Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
GB - 5
control reference guide
Remote Control
1) Video Mode button
9) SUBTITLE button
Adjusts Brightness, Contrast or Colour of the LCD
screen.
2)
PREV button
Moves back through titles, chapters or tracks on a
menu of a DVD.
/
SEARCH: Fast reverse playback.
SEARCH: Fast forward playback.
SEARCH buttons
10) AUDIO button
output mode on a CD.
11) ANGLE button
Skips directly to a location on a DVD.
5) Cursor (
,
,
,
) buttons
Use to move between selections on a menu screen
with multiple camera angles.
ENTER button
12) DISPLAY button
Confirms selections on a menu screen.
6) MEMORY button
13)
In STOP mode, sets titles/chapters in a favourite
order.
7) Number (0 - 9) buttons
Use when creating programs, entering parental
control password or locating a title/chapter/track
or specific time.
14)
8) REPEAT A-B button
Performs point-to-point repeat playback on a DVD
STOP button
Stops playing a disc.
PLAY button
Starts or resumes playback of a disc.
PAUSE button
Pause playback and frame advance.
NEXT button
Moves forward through titles, chapters or tracks on
a disc.
15) MENU button
REPEAT DISC button
Enters and exits the main DVD menu.
Repeats a CD track or the entire disc.
Shows status information on the screen.
or CD.
Repeats a DVD chapter or title.
Switches between multiple camera angles when
the DVD you are playing has been programmed
and adjust certain settings.
Selects one of the audio sound tracks on a DVD
(if more than one is available) or select the audio
4) GOTO button
RETURN button
Returns to normal operation after using the SETUP
disc.
3)
Selects one of the subtitle languages programmed
on a DVD (if available).
SETUP button
When a DVD is stopped, brings up the unit’s SETUP
menu.
GB - 6
control reference guide
DVD UNIT
MONITOR
1) Remote Sensor
1) VOLUME Control
Receives the remote control signal.
2)
2) Headphone Jack
3)
Button
Press the button and hold the front panel to open
3) AUDIO/VIDEO IN jacks
the disc door.
4) DC IN 9V-12V jack
SEARCH Button
5) LCD Screen
6) COLOR Control
Press to perform fast reverse playback.
SEARCH Button
PREV Button
8) Screen Switch:
NEXT Button
WIDE: Wide Screen
Press to select next title, chapters or tracks on a
NORMAL: Pan Scan
disc.
9) ON/OFF Switch
STOP Button
10) DC IN 9V-12V jack
11) POWER ON Indicator
Stops playing a disc.
PAUSE Button
Pauses playback of a disc and frame advance.
Starts or resumes playback of a disc.
DC IN 9-12V Jack
When the STANDBY / ON switch is in the ON
position, the green light will illuminate.
PLAY Button
12) Stand
4) STANDBY(power off ) / ON Switch
5) LCD Screen
6) Headphone Jack
7) VOLUME Control
Adjusts the volume.
8) AUDIO/VIDEO OUT jacks
9) DC IN 9V-12V jack
10) POWER ON Indicator
Adjusts the relative lightness or darkness of a
screen. Press to select previous chapters or tracks on a
Adjusts the color intensity.
7) BRIGHTNESS Control
Press to perform fast forward playback.
disc.
Adjusts the volume.
When the STANDBY / ON switch is in the ON
position, the green light will illuminate.
11) Stand
GB - 7
POWER SUPPLY
A. Using the AC Power Adapter
The supplied AC power adapter operates on AC between 100V and 240V.
Using the Main unit and the monitor together
4 TO AC outlet
MONITOR left side
UNIT - right side
right side
DC-AV cable
(included)
AC ADAPTER
3 TO DC IN 9V-12V jack
1
TO A/V OUT &
DC IN 9V-12V
jacks
2
TO A/V IN &
DC OUT 9V12V jacks
Using the Main unit or the monitor separately
UNIT - right side
MONITOR - right side
2
2
TO AC outlet
TO AC outlet
AC ADAPTER
AC ADAPTER
IN 9V-12V
1 DC
jack
1 jack
DC IN 9V-12V
Cautions:
•
•
The AC power adapter included with this unit is for
•
apparatus is not completely disconnected from
When the unit is not going to be used for long
the main power supply, even when the power is
time, disconnect the AC power adapter from the
AC power outlet.
•
When the AC power adapter is plugged in, the
its use only. Do not use it with other equipment.
turned off.
•
Be sure to use it near the wall outlet and easily
Turn off the unit before unplugging the AC power
accessible. If a malfunction occurs, disconnect the
adapter from the unit to avoid the unit being
plug from the wall outlet at once.
damaged.
GB - 8
POWER SUPPLY
B. Using the Car Power Adapter
The 12V car power adapter allows the unit to be used with vehicles that have a 12V, negative ground electrical
system.
Using the Main unit and the Monitor together
UNIT - right side
MONITOR -
left side
right side
4
DC-AV cable
(included)
To the
cigarette
lighter socket
CAR POWER
ADAPTER
3 TO DC IN 9V-12V jack
1DC IN 9V-12V
TO A/V OUT &
jacks
2
TO A/V IN &
DC OUT 9V12V jacks
Using the Main unit or the monitor separately
MONITOR - right side
UNIT - right side
CAR POWER
ADAPTER
CAR POWER
ADAPTER
To the
cigarette
2
cigarette
To the
2
lighter socket
lighter socket
IN 9V-12V
1 DC
jack
1 jack
DC IN 9V-12V
WARNING:
IMPORTANT
Disconnect the car power adapter when
This car adapter is for use with 12 volt
not in use. Not for use in 24V vehicles.
batteries only.
Cautions:
•
•
Use the provided 12V car power adapter only. Use
with other car power adapters could damage the
unit.
•
of an accident.
•
When the inside of the cigarette lighter socket
The 12V car power adapter included with this
is dirty with ashes or dust, the plug section may
unit is for its use only. Do not use it with other
become hot due to poor contact. Be sure to clean
equipment.
•
Make sure the unit is securely fastened to prevent
it from falling or flying through the air in the event
the cigarette lighter socket before use.
In the interest of traffic safety, do not operate this
•
unit or view videos while driving a vehicle.
After use, disconnect the 12V car power adapter
from both the unit and cigarette lighter socket.
GB - 9
CONNECtions
A. Watching a DVD on the Main Unit and the Monitor
You can watch the same DVD on the main unit and the monitor.
MONITOR UNIT - right side
left side
right side
DC-AV cable
(included)
TO A/V OUT
& DC IN 9V12V jacks
TO A/V IN &
DC OUT 9V12V jacks
Watching on the Main Unit and the Monitor
1.Connect the main unit and the monitor using the included DC-AV Cable.
2.Turn on the main unit and the monitor.
3. Play a DVD on the main unit; the monitor will play at the same time by AV IN.
Note: You can also use the included AC power adaptor to supply power.
B. Connecting a TV (for the Main Unit Only)
If your TV has Audio/Video inputs, you can connect the main unit to your TV using a standard AV cable (not
included).
UNIT - right side
AV cable
(not included)
TV
TO A/V IN
TO A/V OUT
jacks
jacks
Watching a DVD on your TV
1. Connect your TV to the main unit using a standard AV cable (not included).
2. Turn on the main unit.
3.Turn on the TV and follow the instructions included with it to play the DVD.
Notes:
• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause a weak signal.
• If your TV does not have Audio/Video inputs, you will need to purchase an RF modulator (sold separately) and
follow the instructions included with it to connect the unit to your TV.
GB - 10
CONNECtions
C. Listening a Stereo Receiver or Amplifier on Main unit
The main unit can play two channels Dolby Digital.
Listening on External Audio Equipment
1. Connect the main unit to the left/right Audio In jacks on the other equipment using a standard Audio cable (not
included).
2. Turn on the main unit.
3.Turn on your audio equipment and follow the instructions provided with it to select the AUDIO IN function.
UNIT - right side
Audio cable
Notes:
(not included)
• Make sure to use the correct Audio cable. Connecting
TO A/V IN
jacks
the plugs incorrectly may cause a weak signal.
• If you have a stereo VCR, make sure you set it to
stereo mode.
• Due to copyright protection, DVD movies cannot be
Stereo Receiver
copied. If you copy a DVD movie onto a videotape,
/ Amplifier
the resulting copy will be unclear, with poor sound
quality. This is NOT caused by a defective DVD
TO A/V OUT
system.
jacks
D. Connecting Game Systems/Video Equipment (for the Monitor Only)
You can connect game systems or other video equipment for playback through the monitor only. You cannot
connect these systems to the main unit.
Watching video equipment
1.Connect the other equipment to the monitor using a standard AV Cable (not included).
2.Turn on the monitor.
3.Turn on the video equipment and follow the instructions provided with it to playback.
Notes:
• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause a weak signal.
• If you have a mono VCR, the volume level from the speakers will be low.
MONITOR left side
Game System /
Video equipment
AV cable
(not included)
TO A/V OUT
jacks
TO A/V IN
jacks
GB - 11
right side
CONNECtions
E. Using the Monitor with Other Equipment while Playing DVD on the Main Unit
You can use a game console or other video equipment on the monitor while playing a DVD on the main unit.
MONITOR left side
AV cable
(not included)
right side
UNIT - right side
TO AV IN
jacks
Game system/
Video equipment
TO DC IN
9V-12V
jacks
TO DC OUT 9V-12V jack
TO AV OUT
jacks
DC-AV cable
(included)
Watching Video Equipment on the Monitor while Playing DVD on the Main Unit
1.Connect only the power connector between the main unit and the monitor. Do not connect the Audio/Video
portion of the DC-AV cable.
2.Connect the monitor to the other equipment using a standard AV cable (not included).
3.Turn on the main unit, the monitor and the other equipment.
4. Play a DVD on the main unit.
5.Use the monitor for the other equipment.
Notes:
• You can also use the included AC power adaptor to supply power.
• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause a weak signal.
• If you have a mono VCR, the volume level from the speakers will be low.
F. Using Headphones/Earphones
Turn
down
the
volume
before
connecting
the
headphones/earphones. Slowly raise the volume with the
Headphones/Earphones
(1/8" (3.5mm) diameter
plug)
headphones/earphones on until you reach your desired
volume. When headphones/earphones are connected,
the speaker is automatically disabled.
Caution:
Avoid listening to sound at excessive levels which
could be harmful to your ears.
MONITOR - left side
GB - 12
UNIT - right side
PLACEMENT
A. Mounting in the Vehicle
Use the supplied mounting strap to install the main unit and monitor on the back of the vehicle's headrests. Tightly
wrap the mounting strap around the headrest.
Mounting the Main unit
Mounting the Monitor
SAFETY WARNING!
•
•
This unit should never be used by the vehicle's driver or left unsecured in the vehicle while driving.
If this unit is being used in your vehicle, be sure that it is secured or held safely, and does not obstruct any
safety device, including air bags or seat belts.
•
All passengers should wear seat belots when using this unit in a moving vehicle.
•
If in doubt, please contact your vehicle manufacturer for further advice.
B. Using the Stand
You can stand the main unit/monitor up on a desk or
table using the stand on the back.
GB - 13
SOUND system
Dolby Digital
Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can
reproduce from one to 5.1 discrete channels of excellent quality audio.
The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for twochannel listening. An additional Dolby Digital decoder is required for reproduction of the discrete multi-channel
soundtracks available on many DVDs.
Manufactured under license from Dolby Laboratories.
'Dolby' and the double-D symbol
are trademarks of Dolby Laboratories.
Unit operation
Turning on the unit
1.
Slide the STANDBY / ON switch of the main unit and ON / OFF switch on the
monitor to the ON position.
2.The DVD logo (start-up picture) will appear on the screen.
3.After use, slide the STANDBY / ON switch to the STANDBY (power off ) position of
the main unit and ON / OFF switch to the OFF position of the monitor.
GB - 14
Playing a Disc
Basic playback
This owner’s manual explains the basic instructions
specific DVD in question for more information about
for operating this unit. Some DVDs are produced in
the options available on that DVD.
a manner that allows specific or limited operation
during playback. Therefore, this unit may not respond
“
to all operating commands. THIS IS NOT A DEFECT.
Please refer to the instructions accompanying the
1. Slide the STANDBY / ON switch to the ON position.
(Slide the ON / OFF switch on the monitor to the ON
position.)
See CUSTOMIZING THE FUNCTION SETTINGS before
proceeding to step 2.
2. Press the
by the unit or disc.
2. Press the
Playing a Disc
” may appear on the screen during operation. A “
” means that the desired operation is not permitted
PLAY button when you reach the desired
point to resume normal playback.
Notes:
• The DVD player mutes sound and subtitles during
reverse and forward scan of DVDs.
• The fast playback speed may differ depending on
the disc.
OPEN button and hold the front panel to
open the disc door.
3. Hold the disc by its sides and gently push it onto the
spindle with label side facing towards you until you
Skip (Forward / Reverse)
hear a “click”.
• Press the
4. Gently push the disc door closed. It takes a short
while for your unit to load the disc. After loading,
• Press the
for most DVDs, the unit will automatically take you
tracks.
main menu or start playing. If the unit does not
PREV button to go back to current or
previous chapters/tracks.
NEXT button to advance chapters/
• For audio CDs, use the number buttons on the
automatically start playing the DVD, press the
remote control to jump immediately to the desired
PLAY button.
track number.
Pausing Playback (Still Mode)
Press the
press the
PAUSE button. To resume normal playback,
PLAY button.
Each time you press the
PAUSE button, the picture
On some DVDs, the sound is recorded in two or more
formats. Follow the directions below to select the
advances one frame.
preferred language and sound system.
Stopping Playback
Press the
Audio Selection
STOP button at the location where you
want to interrupt playback. To resume playback at the
position where the disc was stopped, press the
PLAY
button.
1. While a disc is playing, press the AUDIO button to
If you press the
STOP button twice, the unit’s memory
will be cleared and pressing the
PLAY button will
show the current audio format number.
2. Press the AUDIO button repeatedly to select the
reset the disc to the beginning.
desired audio format.
Notes:
Fast Forward / Fast Reverse
1. Press the SEARCH
or
SEARCH button when a
disc is playing. Each time you press the SEARCH
or
SEARCH button, the playback speed changes
• If only one audio format is recorded on the DVD, the
number does not change.
• Some DVDs allow you to change audio selections
only via the disc menu. If this is the case, press the
in the following sequence:
MENU button and choose the appropriate language
on the disc menu.
• You can select different audio channels (Stereo, Left
or Right) on an Audio CD by pressing the AUDIO
button repeatedly.
GB - 15
Playing a Disc
Basic playback
Notes:
Subtitle Selection
1. While a DVD is playing, press the SUBTITLE button to
• This function can only be used for discs on which
scenes
display the current language setting, as shown in the
example.
from
multiple
angles
• If only one angle is recorded, “
2. Press the SUBTITLE button repeatedly to select the
desired subtitle language. You can turn subtitles off
by pressing the SUBTITLE button repeatedly until
the “
shot
” is displayed.
have
been
recorded.
” is displayed.
Display Function
While the disc is playing, press the DISPLAY button
repeatedly to display information on operation status.
Notes:
• Some DVDs are set to display subtitles automatically,
and you cannot turn them off even if you set the
subtitle function to off.
• During some scenes, the subtitles may not appear
immediately after you select your desired scene.
• The number of subtitle languages recorded differs
depending on the disc. If only one language is
recorded, the language does not change.
• This function can only be used for discs on which
Elapsed Time:Elapsed time from the beginning of
the title which is currently playing.
subtitles have been recorded in multiple languages.
• Some DVDs allow you to change subtitles only via
the disc menu. If this is the case, press the MENU
Remain Time:Remaining time of the title which is
currently playing.
button and choose the appropriate subtitle on the
disc menu.
Adjust the LCD Screen
Angle Selection
Some DVDs contain scenes which have been shot
from a number of different angles. For these discs, the
same scene can be viewed from each of these different
angles.
1. While you are playing a DVD with different angles
recorded, press the ANGLE button to view the
number of current angles available.
You can adjust Brightness, Contrast or Colour of the
LCD screen.
1. Press the VIDEO MODE button.
2. Press the
3.Then press the
scene to the next recorded angle.
from the new angle you selected.
• If no button is pressed within 10 seconds, playback
continues without changing the current angle.
button to select Brightness, Contrast
/
button to change the setting.
4. Press the VIDEO MODE button again to exit the
menu.
2. Press the ANGLE button repeatedly to change the
• After approx. two seconds, playback will continue
/
or Colour.
Note:
For the monitor, you can adjust the LCD screen by
the BRIGHTNESS control, COLOUR control and Screen
(WIDE / NORMAL) switch on the monitor.
Sequence of angle shots
(Example)
GB - 16
locating a desired section
Locating a Specific Title
If a DVD contains title numbers, you can locate a specific title by directly selecting its title number.
1. Press the GOTO button.
2. Press the corresponding number button(s) for the title you want.
3. Press the ENTER button to confirm. Playback starts from the selected section.
Notes:
• If the title numbers you entered is not permited by the DVD, after you press the ENTER button, it will restore to - - -.
You should re-enter correct numbers.
• Some discs may not respond to this process.
• This method of locating a title is available only on a DVD that contains title numbers.
Locating a Specific Chapter
If you know the chapter number for the chapter that you want to play, you can locate it by directly selecting that
number.
1. Press the GOTO button.
2. Press
or
button to display Chapter and press the corresponding number button(s) for the chapter you
want.
3. Press the ENTER button to confirm. Playback starts from the selected section.
Notes:
• If the chapter numbers you entered is not permited by the DVD, after you press the ENTER button, it will restore
to - - -. You should re-enter correct numbers.
• Some discs may not respond to this process.
• This method of locating a chapter is available only on a DVD that contains chapter numbers.
Locating a Specific Time
You can move to a specific location by entering its corresponding time (hours, minutes, seconds).
1. Press the GOTO button.
2. Press
or
button to display Time and press the corresponding number buttons for the setting point you
want.
3. Press the ENTER button to confirm. Playback starts from the selected section.
Notes:
• If the time numbers you entered is not permited by the DVD, after you press the ENTER button, it will restore to
- - : - - : - -. You should re-enter correct numbers.
• Some discs may not respond to this process.
• Some scenes may not be located as precisely as you specified.
• This method for accessing specific locations is available only within the current title of the DVD.
GB - 17
DVD PROGRAMMABLE MEMORY
Playing TItles/Chapters in a Favourite Order
button. The DVD player starts memory playback.
You can combine your favourite titles/chapters and
4.To resume normal playback from memory playback
play them in the order you determine.
1).Press the MEMORY button in stop mode.
1. When a DVD is stopped, press the MEMORY button,
2).Press the Cursor buttons (
,
,
,
) to move the
highlighted bar to “Clear All”, then press the ENTER
the following display appears.
button. All the input programs will be cleared.
3).Press the
PLAY button to resume normal
playback.
Notes:
• If the title or chapter numbers you entered is not
permited by the DVD, after you press the ENTER
button, it will restore to - - -. You should re-enter
correct numbers.
• Some discs may not permit memory playback
operation.
2. Select the items in the order you want by pressing
the number buttons.Each time you press the Cursor
buttons (
,
,
,
• If you select repeat during memory playback, the
DVD player repeats the current memory playback.
), the space is highlighted.
Highlight where you want to enter, then press the
• If you press the MEMORY button while the display
appears on the TV screen, the display disappears.
corresponding number buttons.
3. Press the Cursor buttons (
,
,
,
) to move the
• The programmed selections will be cleared when
you open the disc tray or turn off the DVD player.
highlighted bar to Play Memory, then press the ENTER
REPEAT PLAYBACK
You can play a specific title or chapter repeatedly. (Title
repeat, chapter repeat, A-B repeat)
To Resume Normal Playback
3. Press the REPEAT DISC button until the “
Repeating a Chapter
” indicator displays on the screen.
1. While the DVD is playing, press the REPEAT DISC
button
until
the
“
”
indicator
displays on the screen. The current chapter is played
repeatedly.
Repeating a Specific Section
You can play a specific section repeatedly.
1. While the disc is playing, press the REPEAT A-B
button at the beginning of the section (“
Repeating a Title
2. While the DVD is playing, press the REPEAT DISC
button until the “
2. Press the REPEAT A-B button again at the end of the
section (“
” indicator displays on
selection.
To Resume Normal Playback
3. While the DVD is playing, press the REPEAT DISC
” indicator displays on
To Resume Normal Playback
4. While the disc is playing, press the REPEAT A-B
button until the “
the screen.
Notes:
repeatedly.
• Some discs may not permit A-B repeat operation.
Repeating a Single Track
• You cannot set the A-B repeat function for a segment
1. While the CD disc is playing, press the REPEAT DISC
” indicator displays
that includes multiple camera angles.
• You can specify a segment only within the current
title or track.
on the screen. The current track is played repeatedly.
• There may be a slight difference between point A
Repeating a Whole Disc
and the location where playback actually resumes
2. While the CD disc is playing, press the REPEAT DISC
button until the “
” indicator displays on
the screen.
You can play a single track or the whole disc
button until the “
” is displayed).
3.The Unit will immediately begin replaying your
the screen. The current title is played repeatedly.
button until the “
”
is displayed) you want to play repeatedly.
” indicator displays on
the screen. The whole disc is played repeatedly.
GB - 18
depending on the disc.
VIEWING JPG FILES
This unit can play JPG files recorded on a CD-R or CD-ROM disc (CD-RW is not recommendable).
Viewing JPG Files
1. Open the disc door.
2. Hold a JPG file disc by its edge and gently push it onto the spindle with the label side
facing up until you hear a “click”.
3.Close the disc door. A list of folders/files will appear on the screen.
4. Press the
or
button to select your desired file, the selected picture will appear at
the lower right corner. Press the
PLAY button to start playback. Press the
button
to display a folder list.
Notes:
• You can press the
PAUSE button to interrupt playback. Press the
• You can press the
STOP button to quit playback.
• You can press the
PREV or
PLAY button to resume playback.
NEXT button to change the picture.
• You can press the ANGLE button to rotate direction of the picture by 90°.
• Some discs may not permit this operation.
PLAY ModeS for CD or JPEG Disc
When play CD / JPG discs, you can modify the Play Modes through the Toolkit which appears on the right of below
picture on the screen. Press the
/
button to navigate between the windows and the
/
button to select
files/tracks or play mode items. Then press the ENTER button.
1.In Stop mode, press the Cursor buttons (
2.Use the Cursor buttons (
,
,
,
,
,
,
) to select "Edit mode" then press the ENTER button.
) to select tracks/files shown on the left hand side of the window. Press the
ENTER button to confirm the selected tracks/files. "
" will appear in front of the selected tracks/files.
3. Select "Add to program", then press the ENTER button. "
" will disappear from the screen. It means that the
tracks/files you have selected are added into the "Program view".
4. Select "Program view" to view programmed files. To add more files by "Browser view" follow above steps.
5. Press the
PLAY button to start the program playback.
The Toolkit has the following play mode items:
• Repeat ( Off / Single / All ):
Off: Resumes normal playback.
Single: Repeats the current track/file.
All: Repeats all files on the current folder or all tracks on the disc.
• Mode ( Normal / Shuffle / Music intro ):
Normal: Resumes normal playback.
Shuffle: Playbacks track/file in random order.
Music intro (for Audio CD only): Only playbacks the first 10 seconds of all the tracks on the current folder/disc.
• Edit mode: Program operation works only when "Edit mode" is selected.
• Program view: To view tracks/files in the "Program view" list. It is disabled when the "Program view" list is
empty.
• Add to program: Add files/tracks to the "Program view" list. It is disabled if the "Edit mode" is not selected.
• Browser view: To view files/tracks in the original view list.
• Clear program: Delete the files/tracks in the "Program view" list.
Select a file/track or more you want to delete in complete stop mode (press the
STOP button twice). "
" will
appear beside the deleted file/track. Select "Clear program" and then press the ENTER button. It is disabled if the
"Edit mode" is not selected.
Note: The program will be deleted if the
STOP button is pressed twice, the disc door is opened, or selected files
are deleted by selecting "Clear program".
GB - 19
CUSTOMIZING THE FUNCTION SETTINGS
Language
OSD Language
1. Press the SETUP button in stop mode.
2. Press the
button to select OSD Language.
3. Press the ENTER button, then the
/
button to shift and
change the Language.
4. Press the ENTER button.
5. Press the SETUP button or RETURN button to exit the menu.
Subtitle
1. Press the SETUP button in stop mode.
2. Press the
button, then the
/
button to select Subtitle.
3. Press the ENTER button, then the
/
button to shift and
change the Language.
4. Press the ENTER button.
5. Press the SETUP button or RETURN button to exit the menu.
Notes:
• Some DVD video discs may be set to display subtitles in a
different language other than the ones you selected. A prior
subtitle language may be programmed on the disc.
• Some DVD video discs allow you to change subtitle selections
only via the disc menu. If this is the case,
press the MENU
button and choose the appropriate subtitle language from the
selection on the disc menu.
Audio
1. Press the SETUP button in stop mode.
2. Press the
button, then the
/
button to select Audio.
3. Press the ENTER button, then the
/
button until your
preferred Audio is displayed.
4. Press the ENTER button.
5. Press the SETUP button or RETURN button to exit the menu.
Note:
• Some DVD video discs may not be played in the language you
selected. A prior language may be programmed on the disc.
DVD Menu
1. Press the SETUP button in stop mode.
2. Press the
button, then the
/
button to select DVD Menu.
3. Press the ENTER button, then the
/
button until your
preferred DVD Menu language is displayed.
4. Press the ENTER button.
5. Press the SETUP button or RETURN button to exit the menu.
Note:
• Some DVD video discs may not include your pre-selected
language. In this case, the DVD player automatically displays
disc menus consistent with the disc's initial language setting.
GB - 20
CUSTOMIZING THE FUNCTION SETTINGS
Video
Aspect Ratio
1. Press the SETUP button in stop mode.
2. Press the
/
3. Press the
button, then the
button to select Video.
/
button to select Aspect Ratio.
4. Press the ENTER button, then the
/
button to shift and change the
aspect ratio.
5. Press the ENTER button.
6. Press the SETUP button or RETURN button to exit the menu.
Notes:
• The displayable picture size is preset on the DVD video disc. Therefore, the playback picture of some DVD video
discs may not conform to the picture size you select.
• When you play DVD video discs recorded in the 4:3 picture size only, the playback picture always appears in the
4:3 picture size regardless of the Aspect Ratio setting.
• Select 16:9 to conform to the LCD screen on the unit. Always be sure that your Aspect Ratio conforms to the
actual TV in use if you connect the unit to a TV.
View Mode
1. Press the SETUP button in stop mode.
2. Press the
/
3. Press the
button, then the
button to select Video.
/
button to select View Mode.
4. Press the ENTER button, then the
/
button to shift and change
the View Mode.
5. Press the ENTER button.
6. Press the SETUP button or RETURN button to exit the menu.
FillFill the screen with decoded image.
Original
Display image as it’s original size.
Auto FitAutomatically fit the decoded image on screen without distortion. Black bars will be present on top/
bottom or left/right of screen.
Pan Scan
Select when a standard 4:3 TV is connected. Displays pictures cropped to fill your TV screen. Sides of
the picture are cut off.
Note:
• Depending on the DVD video discs, you may not be able to view the mode as selected.
Misc
Use Default Settings
1. Press the SETUP button in stop mode.
2. Press the
/
3. Press the
button, then press the
button to select Misc.
/
button to select “Use Default
Settings” dialogue box.
4. Press the ENTER button, then press the
/
button to select “Yes”. Press
the ENTER button and the original setting will be restored. The unit will exit
setting menu automatically and re-load the disc in the disc tray.
Note: It will take 3-5 seconds to reset the DVD player to the factory default.
Screen Saver
1. Press the SETUP button in stop mode.
2. Press the
/
3. Press the
button, then press the
button to select Misc.
/
4. Press the ENTER button, then press the
button to select Screen Saver.
/
button to change the On/
Off mode.
5. Press the ENTER button.
6. Press the SETUP button or RETURN button to exit the menu.
GB - 21
MAINTENANCE
heart shaped, octagonal, etc.). They may cause
Cleaning the Disc
malfunctions.
A defective or soiled disc inserted into the unit can
cause sound to drop out during playback.
Cleaning the Unit
Handle the disc by holding its inner and outer edges.
•
•
Do NOT touch the surface of the unlabeled side of
the disc.
•
•
•
are extremely dirty, wipe clean with a cloth that has
the surface.
been dipped in a weak soap-and-water solution
Do NOT expose the disc to
and wrung out thoroughly. Then wipe with a dry
cloth.
heat.
•
•
Never use alcohol, benzine, thinner, cleaning fluid
Clean the disc before playback. Wipe the disc from
or other chemicals. Do NOT use compressed air to
the center outward with a cleaning cloth.
remove dust.
NEVER use solvents such as benzine or alcohol to
clean the disc.
•
Wipe the unit with a dry soft cloth. If the surfaces
Do NOT stick paper or tape on
direct sunlight or excessive
•
Be sure to turn the unit off and disconnect the car
power adapter before maintaining the unit.
Do NOT use irregular shaped discs (example:
Important Note
•
Before transporting the unit, remove any disc from
the disc compartment.
TROUBLESHOOTING GUIDE
SYMPTOM
CAUSE (AND REMEDY)
No power.
• Ensure the AC power adapter or car power adapter is connected.
• Make sure that the unit is turned on.
The remote does not
• Remove any obstacles between the remote and the unit.
function.
• Use the remote near the unit.
• Point the remote at the remote sensor on the unit.
• Replace all the battery in the remote with new ones.
Very little or no sound
• Make sure that you select ON mode.
is coming from a DVD.
• Make sure the unit is not paused. Press the
PLAY button.
• Make sure the unit is not in fast-forward or fast-reverse mode. Press the
PLAY
button.
• Make sure the AUDIO/VIDEO input/output connections are correct.
• The DTS DVD cannot be decoded to have speaker output.
• The unit has overheated. Shut it off for 30 minutes to allow it to cool down.
No picture.
• The region number of the disc doesn't match the region number of this unit.
The picture is not clear.
• The DVD is dirty. Gently clean the disc.
• The disc is scratched.
• Please adjust the LCD's brightness, contrast and colour using the VIDEO MODE
button on the remote control for the main unit and the brightness, colour control on
the monitor.
Loud hum or noise is
heard.
• The plugs and jacks are dirty. Wipe them with a cloth slightly moistened with
alcohol.
• Clean the disc.
The disc does not play.
• There is no disc inside the unit ("No Disc" appears on the screen).
• Insert the disc correctly with the graphics facing up.
• Clean the disc.
• A non-NTSC disc has been inserted, or the disc region number does not match the
region number of the unit.
• Condensation may have formed inside the unit due to a sudden change in
temperature. Wait about an hour for it to clear and try again.
Specifications and external appearance are subject to change without notice.
GB - 22
GFM Guarantee
GFM Guarantee
If you are not totally satisfied with this GFM product, you may return it to any Meijer store for a full refund within
6 months (180 days) of purchase when accompanied by a receipt.
For customer support please call (866) 845-9436 or go to www.gfmproducts.com
Dist. by Wholesale Merchandisers, Inc.,
2929 Walker, NW
Grand Rapids, MI 49544
Made in China
Printed in China
811-798991W010
GB - 23
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement