BMW Multi Tool User Manual

BMW Multi Tool User Manual
BMW Multi Tool User Manual
X-Horse Electronics Co., Ltd.
http://www.obdchina.com/
BMW Multi Tool User Manual
Table of Contents
1.
2.
3.
4.
5.
6.
Safety Precautions and Warnings ................................................................................ 3
General Information ...................................................................................................... 4
Hardware Overview ...................................................................................................... 5
3.1. Tool Description ................................................................................................. 5
3.2. Specifications..................................................................................................... 6
3.3. System Requirements ....................................................................................... 7
Software Overview ....................................................................................................... 8
4.1. Overview ............................................................................................................ 8
4.2. Function ........................................................................................................... 11
Troubleshooting .......................................................................................................... 30
5.1. “Device not connected”Error ........................................................................... 30
Warranty and Service ................................................................................................. 31
6.1. Limited One Year Warranty ............................................................................. 31
6.2. Service Procedures ......................................................................................... 31
2
http://www.obdchina.com/
BMW Multi Tool User Manual
1. Safety Precautions and Warnings
To prevent personal injury or damage to vehicles and/or the tool, read
this instruction manual first and observe the following safety
precautions at a minimum whenever working on a vehicle:










Always perform automotive testing in a safe environment.
Wear safety eye protection that meets ANSI standards.
Keep clothing, hair, hands, tools, test equipment, etc. away from all moving
or hot engine parts.
Operate the vehicle in a well ventilated work area: Exhaust gases are
poisonous.
Put blocks in front of the drive wheels and never leave the vehicle
unattended while running tests.
Use extreme caution when working around the ignition coil, distributor cap,
ignition wires and spark plugs. These components create hazardous
voltages when the engine is running.
Put the transmission in PARK (for automatic transmission) or NEUTRAL
(for manual transmission) and make sure the parking brake is engaged.
Keep a fire extinguisher suitable for gasoline/chemical/electrical fires
nearby.
Don’t connect or disconnect any test equipment while the ignition is on or
the engine is running.
Keep the tool dry, clean, free from oil/water or grease. Use a mild
detergent on a clean cloth to clean the outside of the scan tool, when
necessary.
3
http://www.obdchina.com/
BMW Multi Tool User Manual
2. General Information
Thank you for choosing BMW Multi Tool.
This manual includes the use of equipment notes, please read this manual
carefully before use so that you can correctly use it.
X-Horse Electronics, 2011
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form, or by any means, mechanical, electronic,
photocopying, recording, or otherwise, without the prior written permission of X-Horse
Electronics.
All copyright and trademarks acknowledged.
No patent liability is assumed with respect to the use of the information contained
herein. Moreover, because X-Horse Electronics is constantly striving to improve its
high-quality products, the information contained in this manual is subject to change
without notice. Every precaution has been taken in the preparation of this manual.
Nevertheless, X-Horse Electronics assumes no responsibility for errors or omissions.
Neither is any liability assumed for damages resulting from the use of the information
contained in this publication.
4
http://www.obdchina.com/
BMW Multi Tool User Manual
3. Hardware Overview
3.1. Tool Description
ITEM
Description
❶
OBD II CONNECTOR
❷
Dongle
❸
USB CONNECTOR
❹
Programmer
❺
Programmer Female Pin
❻
Programmer Male Pin
Connects the tool to the vehicle’s Data Link connector (DLC).
USB dongle.
Connects the tool to the PC/Laptop through USB Cable.
Program keys.
Connects programmer to device.
Connects programmer to device.
5
http://www.obdchina.com/
BMW Multi Tool User Manual
3.2. Specifications
ITEM
Description
Operating Temperature
-20 to 70 °C
( -4 to 158 °F )
Storage Temperature
-40 to 85 °C
( -40 to 185 °F )
Diagnostic Interface
16 PIN
USB Interface
USB 2.0
Power
DC 5 V - 12 V
Consumption
1W
Dimensions
Length
95 mm(3.74″)
Net Weight
85 g
Gross Weight
223 g
Width
49 mm(1.93″)
6
http://www.obdchina.com/
Height
28 mm(1.10″)
BMW Multi Tool User Manual
3.3. System Requirements
PC/Laptop Minimum Specification
Minimum Specification
CPU
Pentium 3/1GHz or above
Memory(RAM) 512M or above
Recommended Specification
Pentium 4/1.6GHz or above
1G or above
HDD
40G or above
60G or above
Display
800 x 600 or above
1024 x 768 or above
OS
Win98/2000/XP/Vista
WinXP
Port
USB
USB
7
http://www.obdchina.com/
BMW Multi Tool User Manual
4. Software Overview
4.1. Overview
BMW Multi Tool includes forth parts, hardware device, dongle, programmer,
software. Before running software you must connect dongle and hardware
device to computer.
1. OBD II: BMW Multi Tool connects to car directly.
2. CAS PLUG: Connect CAN line manually, support 12V. Detail method followed in next
page.
3. Support EEPROM dump: get EEPROM dump with programmer.
8
http://www.obdchina.com/
BMW Multi Tool User Manual
1. 7 Series CAS1/CAS2 pin method:
2. CAS2(While Box)/CAS3/CAS3+ pin method:
9
http://www.obdchina.com/
BMW Multi Tool User Manual
3. Device pin method:
10
http://www.obdchina.com/
BMW Multi Tool User Manual
4.2. Function
Main window follows:
i.
Menu
Tool: you can choose language here, support “English” and “Chinese
Simplified” Restart software to apply your settings.
File Make Key: you can prepare dealer key with EWS and CAS EEPROM dump.
Help: Device update. You can get your device and dongle id version and update
it.
Unlock Key: Key make by this software can be unlocked with the original
EEPROM dump or key file.
File Change KM: KM stored in CAS EEPROM and instrument dashboard
(M35080) can be changed here.
11
http://www.obdchina.com/
BMW Multi Tool User Manual
ii.
Protocal type:
Now BMT support there type of protocol: KWP-CAN BUS 100Kbps, KWP-CAN
BUS 500Kbps, KWP-2000. “Auto Detect ” function can help you to choose the
right protocol. After choose protocol okay, then press “Connect”. If connected
success. All CAS info will display in CAS Identification. Include CAS number,
VIN, production date, etc. see the picture follows:
12
http://www.obdchina.com/
BMW Multi Tool User Manual
iii.
EEPROM Function: Read EEPROM,Write EEPROM,Save File,Load File…
1. You should backup the CAS EEPROM before prepare dealer key. After
succeed read EEPROM, please save it as back file. This step is very
important.
2. Now can’t read the whole EEPROM for cas3 system. But the main
section is contained. It should be saved. When you read CAS EEPROM, it
will give tips as follow(Press ok to continue):
13
http://www.obdchina.com/
BMW Multi Tool User Manual
3. After success read it, you will get:
4. Write EEPROM function is only support CAS1, CAS2 system. Doesn’t
support write to CAS3 system. (Write EEPROM to CAS1/CAS2 system
need CAS PLUG).
14
http://www.obdchina.com/
BMW Multi Tool User Manual
iv.
Odometer: Support read and change KM stored in CAS system. Don’t
support to change KM in instrument. If you want to change the KM display in
instrument. You should change KM in CAS system first. Then modify the KM
in instrument manually. Read KM :
When you try to write KM to CAS system, you will get the following tips: Press
OK to continue.
15
http://www.obdchina.com/
BMW Multi Tool User Manual
16
http://www.obdchina.com/
BMW Multi Tool User Manual
17
http://www.obdchina.com/
BMW Multi Tool User Manual
v.
Synchronization Codes:
1、 CAS3 code-DME 、CAS3code-EGS: Read and write DME and EGS code
stored in CAS3 system.
2、 Synchronize DME and CAS— this function will be useful while prepare
dealer key or any other operation which cause can’t start the engine.
3、 Synchronize CAS and ELV — this function can help clear wheel errors.
4、 Once lost all working key, please don’t run this function.
18
http://www.obdchina.com/
BMW Multi Tool User Manual
vi.
Key Learn
Function introduction:
1. Get Key Info: With this function you can get the key cutting, remote
frequency, and key data.
2. Save Key Info: Save the read key info.
3. Load Key Info: Load the saved key info. To see the key data and prepare
for write key info.
4. Write Key Info: Write the loaded key info into CAS system.
5. Make Dealer Key: You can prepare dealer key after you get key info
successfully. Also you should choose the key position.
6. Add key: Add the new dealer key into CAS system. Some CAS system
needs this step to start the engine.
7. Enable Key: Insert a working key, choose the key position which you
want to disable. The key position can’t be same with the key in ignition.
8. Disable Key: Insert a working key, choose the key position which you
want to enable. The key position can’t be same with the key in ignition.
9. Clear DTC: Before prepare dealer key and after it you can use this
function to clear DTC.
10. Clear Shadow:Before prepare dealer key and after it you can use this
function to clear Shadow.
19
http://www.obdchina.com/
BMW Multi Tool User Manual
vii.
File Make Key
1. Choose CAS or EWS type. It will tips you:
20
http://www.obdchina.com/
BMW Multi Tool User Manual
2. Load the choose EEPROM file you will get the make dealer key window:
21
http://www.obdchina.com/
BMW Multi Tool User Manual
3. Choose key position and press “Make Dealer Key” button. Flow the
given tips to prepare dealer key. After succeed you can save the new
EEPROM dump file.
For EWS1, EWS2, EWS3, EWS4, CAS1, CAS2, CAS3 type the prepared dealer
key can start the engine directly.
For some CA3+ type you need to write back the new dump file into car.
4. CAS3 encrypt data, only OBDII prepare make key is support for CAS3 encrypt
data.
22
http://www.obdchina.com/
BMW Multi Tool User Manual
viii.
Device Update
Open this window after connect to internet. You can see the latest software
version, firmware version, dongle version. You can go to our website for further
information. After succeeded update device firmware, must reconnect the
hardware to computer.
1. Device Info: Get dongle and hardware SN and version.
23
http://www.obdchina.com/
BMW Multi Tool User Manual
2. Device Update: This function can update the dongle and device.
24
http://www.obdchina.com/
BMW Multi Tool User Manual
Process to prepare dealer key:
1. On main window choose “Connect” to auto detect the current car protocol
and get the CAS info.
2. On main window choose “Read EEPROM” to read the CAS EEPROM file and
save it.
3. On main window choose “Key Learn” button to get key learn window.
4. On Key Learn window choose “Get Key Info” to get the key info stored in
CAS system.(picture 2).
5. Choose “Save Key Info” button to save the read key info for backup.
6. Check the connection between programmer and device. Keep connection
while make key process.
7. Put new blank key into the center of programmer.
8. Choose the position where you want to suit the key.
9. Press “Make Dealer Key” to prepare dealer key. After succeed you will get
(picture 3)
“Key make okay and locked. Please use it start the car. If can’t start engine,
use “Add Key” function add the new dealer key to CAS system.” Once can start
the engine, go to step 13.
10. Put the new dealer key into programmer. Use “Add Key” function to add the
key to CAS system. After that you will get (picture 4):”New dealer key
success written to CAS system. You can start engine with the new key now.
If can’t please use the original working key first.”
11. Please return to main widow and use function “Synch DME-CAS” to
synchronize DME (ECU) with CAS.
12. Use “Synch CAS-ELV” to clear wheel errors.
13. Enter to key learn window use “Clear DTC” and “Clear Shadow” function
clear all error sin CAS system.
While prepare dealer key process. Once you get the tips like picture 1, remove
the key from ignition switch, if key has keyless, take the key out of car.
25
http://www.obdchina.com/
BMW Multi Tool User Manual
Picture 1:
26
http://www.obdchina.com/
BMW Multi Tool User Manual
Picture 2:
27
http://www.obdchina.com/
BMW Multi Tool User Manual
Picture 3:
28
http://www.obdchina.com/
BMW Multi Tool User Manual
Picture 4:
Warning: Make sure connect dongle to compute before run the software.
29
http://www.obdchina.com/
BMW Multi Tool User Manual
5. Troubleshooting
5.1. “Device not connected”Error
Information: Hardware not connected to PC with USB port.
Solution: Plug device to USB.
30
http://www.obdchina.com/
BMW Multi Tool User Manual
6. Warranty and Service
6.1. Limited One Year Warranty
X-Horse warrants to its customers that this product will be free from all defects
in materials and workmanship for a period of one(1) year from the date of the
original purchase, subject to the following terms and conditions:



This warranty does not apply to damages caused by improper use,
accident, flood, lightning, or if the product was altered or repaired by
anyone other than the Manufacturer’s Service Center.
X-Horse shall not be liable for any incidental or consequential damages
arising from the use, misuse, or mounting of the tool. Some states do not
allow limitations on how long an implied warranty lasts, so the above
limitations may not apply to you.
All information in this manual is based on the latest information available at
the time of publication and no warranty can be made for its accuracy or
completeness. X-Horse reserves the right to make changes at any time
without notice.
6.2. Service Procedures
If you have any questions, please post at http://www.x-horses.com/forum/
31
http://www.obdchina.com/
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement