IBJECT12K10A & IBJECT12K10B

IBJECT12K10A & IBJECT12K10B
IBJECT12K10A &
IBJECT12K10B
User Manual
Manufactured by
Italy
File Name:
IBJECT12K10A_IBJECT12K10B_ING_1.0.indb
Version:
1.0
Date:
06/02/2009
Revision History
Date
Version
06/02/2009 1.0
Reason
First Edition
Editor
J. H. Berti
IBJECT12K10A & IBJECT12K10B - User Manual
Version 1.0
© Copyright 2009
R.V.R. Elettronica SpA
Via del Fonditore 2/2c - 40138 - Bologna (Italia)
Telephone: +39 051 6010506
Fax: +39 051 6011104
Email:
[email protected]
Web:
www.rvr.it
All rights reserved
Printed and bound in Italy. No part of this manual may be reproduced,
memorized or transmitted in any form or by any means, electronic
or mechanic, including photocopying, recording or by any information storage and retrieval system, without written permission of the
copyright owner.
HD Radio™ Technology Manufactured Under License From iBiquity
Digital Corp. U.S. and Foreign Patents. The HD Radio™ and HD
Radio logo are proprietary trademarks of iBiquity Digital Corp.
IBJECT12K10A & IBJECT12K10B
Table of Contents
1.
2.
3.
3.1
3.2
4.
4.1
5.
5.1
6.
6.1
7.
Preliminary Instructions
Warranty
First Aid
Treatment of electrical shocks
Treatment of electrical Burns
Unpacking
General Description
Installation and configuration procedure
Preparation
External Description
Front Panel
Technical Specifications
User Manual
Rev. 1.0 - 06/02/09
1
1
2
2
2
3
3
4
4
7
6
7
IBJECT12K10A & IBJECT12K10B
This page was intentionally left blank
ii
Rev. 1.0 - 06/02/09
User Manual
IBJECT12K10A & IBJECT12K10B
IMPORTANT
The symbol of lightning inside a triangle placed on the product, evidences the operations for
which is necessary gave it full attention to avoid risk of electric shocks.
The symbol of exclamation mark inside a triangle placed on the product, informs the user
about the presence of instructions inside the manual that accompanies the equipment, important for the efficacy and the maintenance (repairs).
1. Preliminary Instructions
WIRING: This device has a connection to ground
on the power cord and on the chassis. Check that they
are correctly connected.
• General foreword
Operate with this device in a residential ambient can cause
radio disturbs; in this case, it can be demanded to the user
to take adequate measures.
The equipment in object is to considering for uses,
installation and maintenance from “trained” or “qualified”
staff, they conscious of the risks connected to operate
on electronic and electrical circuits electrical. The “trained” definition means staff with technical
knowledge about the use of the equipment and with
responsibility regarding the own safety and the other
not qualified staff safety place under his directed
surveillance in case of works on the equipment. The “qualified” definition means staff with instruction and
experience about the use of the equipment and with
responsibility regarding the own safety and the other not
qualified staff safety place under his directed surveillance
in case of works on the equipment.
Specifications and informations contained in this manual
are furnished for information only, and are subject to change
at any time without notice, and should not be construed
as a commitment by R.V.R. Elettronica SpA.
The R.V.R. Elettronica SpA assumes no responsability or
liability for any errors or inaccuracies that may appear in
this manual, including the products and software described
in it;and it reserves the right to modify the design and/or
the technical specifications of the product and this manual
without notice.
• Warning regarding the use designated and the use
limitations of the product.
WARNING: The machine can be equipped with
an ON/OFF switch which could not remove completely
voltages inside the machine. It is necessary to
have disconnected the feeding cord, or to have
switched off the control panel, before to execute
technical operations, making sure himself that the
safety connection to ground is connected.
The technical interventions that expect the equipment
inspection with circuits under voltage must be carry out
from trained and qualified staff in presence of a
second trained person that it is ready to intervene
removing voltage in case of need.
R.V.R. Elettronica SpA doesn’t assume responsibility for
injury or damage resulting from improper procedures or
practices by untrained/unqualified personnel in the handling
of this unit.
This product is an transmitter radio indicated
for the audio broadcasting service in frequency
modulation. It uses working frequencies that are not
harmonized in the states of designated user.
The user of this product must obtain from the Authority
for spectrum management in the state of designated
user the appropriate authorization to use the radio
spectrum, before putting in exercise this equipment.
The working frequency, the transmitter power, let alone
other specifications of the transmission system are subject
to limitation and definited in the authorization obtained.
2. Warranty
R.V.R. Electronics S.P.A. guarantees absence of
manufacturing defect and the good operation for the
products, within the provided terms and conditions.
WARNING: The equipment is not water resistant
and an infiltration could seriously compromise
its correct operation. In order to prevent fires or
electric shocks, do not expose the equipment to rain,
infiltrations or humidity.
Please read the terms carefully, because the purchase of
the product or acceptance of order confirmation, constitutes
acceptance of the terms and conditions.
Please observe all local codes and fire protection standards
during installation and use of this unit.
Warranty will be void in cases of opened products, physical
damage, misuse, modification, repair by unauthorised
persons, carelessness and using the product for other
purpose than its intended use.
WARNING: The equipment has to its inside
exposed parts to risk of electric shock, always
disconnect power before opening covers or removing
any part of this unit.
Fissures and holes are supplied for the ventilation in order
to assure a reliable efficacy of the product that for protect
itself from excessive heating, these fissures do not have
to be obstructed or to be covered. The fissures doesn’t be
obstructed in no case. The product must not be incorporated
in a rack, unless it is supplied with a suitable ventilation or
that the manufacturer’s instructions are been followed.
WIRING: This equipment can irradiate radio
frequency energyand if it’s not installed following
the instructions contained in the manual and local
regulations it could generate interferences in radio
communications.
User Manual
For the last legal terms and conditions, please visit our web
site (WWW.RVR.IT) wich may also be changed, removed
or updated for any reason without prior notice.
In case of defect, proceed like described in the following:
1 Contact the dealer or distributor where you purchased
the unit. Describe the problem and, so that a possible
easy solution can be detected.
Dealers and Distributors are supplied with all the information
about problems that may occur and usually they can repair
the unit quicker than what the manufacturer could do. Very
often installing errors are discovered by dealers.
2 If your dealer cannot help you, contact R.V.R. Elettronica
and explain the problem. If it is decided to return the
unit to the factory, R.V.R. Elettronica will mail you a
regular authorization with all the necessary instructions
to send back the goods;
3 When you receive the authorization, you can return the
unit. Pack it carefully for the shipment, preferably using
the original packing and seal the package perfectly.
The customer always assumes the risks of loss (i.e.,
Rev. 1.0 - 06/02/09
/8
IBJECT12K10A & IBJECT12K10B
R.V.R. is never responsible for damage or loss), until
the package reaches R.V.R. premises. For this reason,
we suggest you to insure the goods for the whole value.
Shipment must be effected C.I.F. (PREPAID) to the
address specified by R.V.R.’s service manager on the
authorization
DO NOT RETURN UNITS WITHOUT OUR
AUTHORIZATION AS THEY WILL BE REFUSED
4 Be sure to enclose a written technical report where
mention all the problems found and a copy of your
original invoice establishing the starting date of the
warranty.
Figure 5
Replacement and warranty parts may be ordered from
the following address. Be sure to include the equipment
model and serial number as well as part description and
part number.
R.V.R. Elettronica SpA
Via del Fonditore, 2/2c
40138 BOLOGNA ITALY
Tel. +39 051 6010506
3. First Aid
3.1.2
•
In case of only one rescuer, 15 compressions
alternated to two breaths.
•
If there are two rescuers, the rythm shall be of
one brath each 5 compressions.
•
Do not interrupt the rythm of compressions
when the second person is giving breath.
•
Call for medical assistance as soon as possible.
If victim is responsive
•
Keep them warm.
The personnel employed in the installation, use and
maintenance of the device, shall be familiar with theory and
practice of first aid.
•
Keep them as quiet as possible.
•
Loosen their clothing (a reclining position is
recommended).
3.1
•
Call for medical help as soon as possible.
3.1.1
Treatment of electrical shocks
If the victim is not responsive
Follow the A-B-C’s of basic life support.
•
Place victim flat on his backon a hard
surface.
•
Open airway: lift up neck, push forehead back
3.2
3.2.1
(Figure 1).
Treatment of electrical Burns
Extensive burned and broken skin
•
Cover area with clean sheet or cloth.
•
Do not break blisters, remove tissue, remove
adhered particles of clothing, or apply any salve
or ointment.
•
Treat victim for shock as required.
•
Arrange transportation to a hospital as quickly
as possible.
•
If arms or legs are affected keep them
elevated.
If medical help will not be available within an hour and
the victim is conscious and not vomiting, give him a weak
solution of salt and soda: 1 level teaspoonful of salt and
1/2 level teaspoonful of baking soda to each quart of water
(neither hot or cold).
Figure 1
•
clear out mouth if necessary and observe for
breathing
•
if not breathing, begin artificial breathing
(Figure 2): tilt head, pinch nostrils, make airtight
seal, four quick full breaths. Remember mouth
to mouth resuscitation must be commenced as
soon as possible.
Allow victim to sip slowly about 4 ounces (half a glass) over
a period of 15 minutes.
Discontinue fluid if vomiting occurs.
DO NOT give alcohol.
3.2.2 Less severe burns
Figure 2
•
Check carotid pulse (Figure 3); if pulse is
absent, begin artificial circulation (Figure 4)
depressing sternum (Figure 5).
Figure 3
/8
•
Apply cool (not ice cold) compresses using the
cleansed available cloth article.
•
Do not break blisters, remove tissue, remove
adhered particles of clothing, or apply salve or
ointment.
•
Apply clean dry dressing if necessary.
•
Treat victim for shock as required.
•
Arrange transportation to a hospital as quickly
as possible.
•
If arms or legs are affected keep them
elevated.
Figure 4
Rev. 1.0 - 06/02/09
User Manual
IBJECT12K10A & IBJECT12K10B
4. Unpacking
The package contains:
1 IBJECT12K10A o IBJECT12K10B
1 User Manual
The following accessories are also available from Your R.V.R. Dealer:
• Accessories, spare parts and cables
4.1 General Description
The IBJECT12K10A and IBJECT12K10B, henceforth to commonly named
IBJECT12K10, manufactured by R.V.R. Elettronica SpA, are injectors able to mix a
digital signal (maximum power 2.5 kW) to an existing FM analog signal (maximum
power 12.5 kW), using the same system of antenna and power cord.
It meets all HD RADIO™ standards and, according to RVR’s philosophy, it has
been made with rugged designs.
The injector has been designed to perform an easy installation.
User Manual
Rev. 1.0 - 06/02/09
/8
IBJECT12K10A & IBJECT12K10B
5. Installation and configuration procedure
This section provides a step-by-step description of equipment installation and
configuration procedure. Follow these procedures closely upon first power-on
and each time any change is made to general configuration, such as when a new
transmission station is added or the injector is replaced.
Once the desired configuration has been set up, no more settings are required
for normal operation.
The topics covered in this section are discussed at greater length in the next
sections, with detailed descriptions of all hardware features and capabilities. Please
see the relevant sections for additional details.
IMPORTANT: When configuring and testing the injector in which the equipment is
integrated, be sure to have the Final Test Table supplied with the equipment ready
at hand throughout the whole procedure; the Final Test Table lists all operating
parameters as set and tested at the factory.
5.1 Preparation
5.1.1 Preliminary checks
Unpack the IBJECT12K10 and immediately inspect it for transport damage. Ensure
that all connectors are in perfect condition.
Provide for the following (applicable to operating tests and putting into service):
√ Connection cable kit including:
• Cables, with connector 1+5/8“ (not included), between IBJECT12K10 and
sources of FM analog transmission, and between IBJECT12K10 and output
in antenna.
• Cables, with connector 7/16 DIN (not included), between IBJECT12K10A and
sources of IBOC digital transmission, and between IBJECT12K10A and output
in dummy load. If you are using the IBJECT12K10B version, use cable with
connector 7/8 EIA.
The IBJECT12K10 must be installed on a rack that includes an anti-strap device
to prevent the possibility of accidental disconnection of feeding conductors.
/8
Warning: Disconnect mains power supply before beginning these
procedure.
Rev. 1.0 - 06/02/09
User Manual
IBJECT12K10A & IBJECT12K10B
An example of connection is represented in the figure below:
HD RADIO SIGNAL GENERATOR
HD RADIO DRIVER
& AMPLIFIER
TDX-IBOC001
E2X LINK EXPORTER
DJ50
DJ1000
ANALOG - DIGITAL COMBINER / INJECTOR
ANALOGIC FM
TRANSMITTING SOURCE
IBJECT12K10
RVR’s transmitting Equipment used:
● PTX-DDSFamily
● PTX-LCDFamily
● TEX-LCDFamily
DUMMY LOAD
Figure 5.1: High level mixed signal
NOTE with the addition in a system of IBJECT12K10 the analogic output is
downgraded of 10% and the digital output of 90%. For example, an analog 10kW
will provide in a antenna 9kW and a digital 1000W will supply 100W.
User Manual
Rev. 1.0 - 06/02/09
/8
IBJECT12K10A & IBJECT12K10B
6. External Description
This section describes the components present on equipment.
6.1 Front Panel
Figure 6.1
[1] ANALOG IN
[2] REJECTED OUT
[3] DIGITAL IN
[4] ANTENNA OUT
/8
RF input connector for analog FM source, 1+5/8” type.
RF ouput connector of rejected power for dummy load, 7/16 DIN
type (IBJECT12K10A version) or 7/8 EIA type (IBJECT12K10B
version).
RF input connector for digital IBOC source, 7/16 DIN type
(IBJECT12K10A version) or 7/8 EIA type (IBJECT12K10B version).
RF output connector for antenna, 1+5/8” type.
Rev. 1.0 - 06/02/09
User Manual
IBJECT12K10A & IBJECT12K10B
7. Technical Specifications
Parameters
Conditions
IBJECT12K10A
IBJECT12K10B
U.M.
Value
Value
Notes
MHz
W
kg
°C
dB
dB
dB
87.5 ÷ 108
12.5 kW Analog and 2.5 kW Digital
About 7 kg
-50 to + 70
At least 38
10
At least 26
87.5 ÷ 108
12.5 kW Analog and 2.5 kW Digital
About 7 kg
-50 to + 70
At least 38
10
At least 26
Whithout condensing
1+5/8" EIA
50
7/16 DIN
50
1+5/8" EIA
50
7/8 EIA
50
1+5/8" EIA
50
7/16 DIN
50
1+5/8" EIA
50
7/8 EIA
50
GENERALS
Frequency range
Rated output power
Weight
Ambient working temperature
Isolation
Coupling
Return Loss
INPUTS
Analog Intput
Digital Input
Connector
Impedance
Connector
Impedance
OUTPUTS
Antenna Output
Rejected output
User Manual
Connector
Impedance
Connector
Impedance
Ohm
Ohm
Ohm
Ohm
Rev. 1.0 - 06/02/09
/8
IBJECT12K10A & IBJECT12K10B
This page was intentionally left blank
/8
Rev. 1.0 - 06/02/09
User Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement