User manual M3

User manual M3
User manual M3
Standard signals 0/4-20 mA, 0-10 VDC
Technical features:
• red display of -19999…99999 digits (optional: green, orange or blue display)
• minimal installation depth: 120 mm without plug-in terminal
• min-/max memory
• 30 parameter driven setpoints
• optical threshold value indication at threshold value exceedance / undercut
• zero-key for triggering of HOLD, TARA
• permanent min-/max-value recording
• volume measurement (totaliser)
• arithmetic function
• zero point slowdown
• programming interlock via access code
• protection class IP65 at the front
• plug-in terminal
• option: sensor supply
• option: digital input
• option: 2 or 4 analog outputs
• option: 2 or 4 relay outputs or 8 PhotoMos outputs
• option: interface RS232 or RS485
M3_11GB.pdf
96x48
Identification
STANDARD TYPES
ORDER NUMBER
Direct current / direct voltage
Gehäusegröße: 96x48 mm
M3-1VR5B.0001.470AD
M3-1VR5B.0001.570AD
M3-1VR5B.0001.670AD
Options – breakdown of order code:
M 3- 1 V R 5 B. 0 0 0 1. 6 7 2 A D
Standard type M-line
Dimension
D physical unit
Installation depth
139 mm, incl. plug-in terminal 3
Housing size
96x48x120 mm (WxHxD)
1
Type if display
V, A
V
Display colour
Blue
Green
Red
Orange
B
G
R
Y
Number of digits
5-digit
Digital input
without
1 digital input
(without sensor supply)
Interface RS232
Interface RS485
Setpoints
0 no setpoints
2 2 relay outputs
4 4 relay outputs
Protection class
7 IP65 / plug-in Terminal
Supply voltage
4 115 VAC
5 230 VAC
6 10-30 VDC galv. insulated
5
Measuring input
1 Direct current, direct voltage
Digit height
14 mm
Version
A A
B
0
I
3
4
Analog output
0 without
X 1x 0-10 VDC, 0/4-20 mA
Y 2x 0-10 VDC, 0/4-20 mA
Sensor supply
0 without
2 10 VDC / 20 mA
(incl. digital input)
3 24 VDC / 50 mA
(incl. digital input)
Please state physical unit by order, e.g. m/min.
Contents
1.
Assembly
2
2.
Electrical connection
3
3.
Function and operation description
5
4.
Setting up the device
7
4.1. Switching on
7
4.2. Standard parametrisation (flat operation level)
7
4.3. Extended parametrisation (professional operation level)
11
4.3.1. Signal input parameters „INP“
11
4.3.2. General device parameters „FCT“
14
4.3.3. Safety parameters „COD“
18
4.3.4. Serial parameters „SER“
19
4.3.5. Analog output parameters 1 „Out“
20
4.3.6. Analog output parameters 2 „Out2“
22
4.3.7. Relay functions „rel“
24
4.3.8. Alarm parameter „AL1…AL8“
26
4.3.9. Totaliser (Volume metering) „tot“
28
4.3.10. Programming interlock „run“
29
4.4. Alarms / Relay
30
4.5. Interfaces RS232 / RS485
5.
Factory settings
31
5.1. Default values
31
5.2. Reset to default values
49
6.
Technical data
50
7.
Safety advice
52
8.
Error elimination
53
1
1. Assembly
1. Assembly
Please read the Safety advice on page 52 before installation and keep this user manual for
future reference.
M3
48,0
3,0
Se
alin
g
9,0
13
Gap for physical unit
1.
2.
3.
After removing the fixing elements, insert the device.
Check the seal to make sure it fits securely.
Click the fixing elements back into place and tighten the clamping screws by hand.
Then use a screwdriver to tighten them another half a turn.
CAUTION! The torque should not exceed 0.1 Nm!
The dimension symbols can be exchanged before installation via a channel on the side!
2
2. Electrical connection
2. Electrical connection
3
2. Electrical connection
Connection examples
Below please find some connection examples that show practical applications. For
devices with current respectivels voltage inputs, without sensor supply.
M3 devices
With current respectively voltage input in combination with a 24 VDC sensor supply.
4
3. Function and operation description
3. Function and operation description
Operation
The operation is divided into three different levels.
Menu level (delivery status)
This level is for the standard settings of the device. Only menu items which are sufficent to
set the device into operation are displayed. To get into the professional level, run through
the menu level and parameterise “prof“ under menu item RUN.
Menu group level (complete function volume)
Suited for complex applications as e.g. linkage of alarms, setpoint treatment, totaliser
function etc. In this level function groups which allow an extended parameterisation of the
standard settings are availabe. To leave the menu group level, run through this level and
parameterise „uloc„ under menu item RUN.
Parameterisation level:
Parameter deposited in the menu item can here be parameterised. Functions, that can be
changed or adjusted, are always signalised by a flashing of the display. Settings that are
made in the parameterisation level are confirmed with [P] and thus safed. By pressing the
„zero-key“ it leads to a break-off of the value input and to a change into the menu level. All
adjustments are safed automatically by the device and changes into operating mode, if no
further key operation is done within the next 10 seconds.
Level
Key
Description
Change to parameterisation level and deposited values.
Menu-level
Keys for up and down navigation in the menu level.
Change into operation mode.
To confirm the changes made at the parameterization level.
Parameterisationlevel
Adjustment of the value / the setting.
Change into menu level or break-off in value input.
Change to menu level.
Menu-group-level
Keys for up and down navigation in the menu group level.
Change into operation mode or back into menu level.
5
3. Function and operation description
Function chart:
6
4. Setting up the device
4. Setting up the device
4.1. Switching on
Once the installation is complete, you can start the device by applying the voltage supply.
Before, check once again that all electrical connections are correct.
Starting sequence
For 1 second during the switching-on process, the segment test (8 8 8 8 8) is displayed
followed by an indication of the software type and, after that, also for 1 second the software
version. After the starting sequence, the device switches to operation/display mode.
4.2. Standard parameterisation: (Flat operation level)
To parameterize the display, press the [P] key in operating mode for 1 second. The display
then changes to the menu level with the first menu item TYPE.
Menu level
Parameterisation level
Selection of the input signal, TYPE:
There are several measuring input options: 0/4-20 mA or 0-10 VDC signals as works
calibration (without application of the sensor signal) and SenSU (voltage) or SENSA
(current) as sensor calibration (with the sensor applied). Confirm the selection with [P]
and the display switches back to menu level.
Setting the measuring range end value, END:
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each
digit with [P]. A minus sign can only be parametrized on the highest value digit. After
the last digit, the display switches back to the menu level. If Sens was selected as
input option, you can only select between noca and cal. With noca, only the previously
set display value is taken over, and with cal, the device takes over both the display
value and the analogue input value.
Setting up the measuring range start/offset value, offs:
Enter the start/offset value from the smallest to the highest digit with [▲] [▼] and
confirm each digit with [P]. After the last digit the display switches back to the menu
level. If Sens was selected as input option, you can only select between noca and cal.
With noca, only the previously set display value is taken over, and with cal, the device
takes over both the display value and the analogue input value.
7
4. Setting up the device
Menu level
Parameterisation level
Setting the decimal point, dot:
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P].
The display then switches back to the menu level again.
Setting up the display time, SEC:
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 sec up
to 1 sec and in increments of 1.0 sec up to 10.0 sec. Confirm the selection by pressing
the [P] button. The display then switches back to the menu level again.
Selection of analog output, Out.rA:
Three output signals are available: 0-10 VDC, 0-20 mA and 4-20 mA, with this
function, the demanded signal is selected.
Setting up the final value of the analog output, Out.En:
The final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and
digit by digit confirmed with [P]. A minus sign can only be parametrised on the highest
digit. After the last digit, the device changes back into menu level.
Setting up the initial value of the analog output, Out.OF:
The final value is adjusted from the smallest digit to the highest digit with [▲] [▼] and
digit by digit confirmed with [P]. A minus sign can only be parametrised on the highest
digit. After the last digit, the device changes back into menu level.
Threshold values / Limits, LI-1:
This value defines the threshold, that activates/deactivates an alarm.
8
4. Setting up the device
Menu level
Parameterisation level
Hysteresis for limit values, HY-1:
The delayed reaction of the alarm is the difference to the threshold value, which is
defined by the hysteresis.
Function for threshold value undercut /exceedance, Fu-1:
A limit value undercut is selected with Louu (for LOW = lower limit value), a limit value
exceedance with High (for HIGH = higher limit value). If e.g. limit value 1 is on a
threshold level of 100 and allocated with function High, an alarm is activated by
reaching of the threshold level. If the threshold value was allocated to Low, an alarm
will be activated by undercutting the threshold value, as long as the hysteresis is zero.
The same applies to LI-1 to LI-2 !
User code (4-digit number-combination, free available), U.CodE:
If this code was set (>0000), all parameters are locked for the user, if LOC has been
selected before under menu item run. By pressing [P] for 3 seconds in operation
mode, the display shows COde. The U.Code needs to be entered to get to the reduced
number of parameter sets. The code has to be entered befor each parametrisation,
until the A.Code (Master code) unlocks all parameters again.
Master code (4-digit number-combination, free available), A.CodE:
All parameters can be unlocked with this code, after LOC has been activated under
menu item run. By pressing [P] for 3 seconds in operation mode, the display shows
COde and enables the user to reach all parametes by entering the A.codE. Under run the
parametrisation can be activated permanently by selecting ULOC or ProF, thus at an
anew pushing of [P] in operation mode, the code needs not to be entered again.
9
4. Setting up the device
Menu level
Parameterisation level
Activation / deactivation of the programming lock or completion of the standard
parameterization with change into menu group level (complete function range),
run:
With the navigation keys [▲] [▼], you can choose between the deactivated key lock
Uloc (works setting) and the activated key lock Loc, or the change into the menu group
level ProF. Confirm the selection with [P]. After this, the display confirms the settings
with "- - - - -", and automatically switches to operating mode. If Loc was selected, the
keyboard is locked. To get back into the menu level, press [P] for 3 seconds in
operating mode. Now enter the CODE (works setting 1 2 3 4) that appears using [▲] [▼]
plus [P] to unlock the keyboard. FAIL appears if the input is wrong. To parameterize
further functions ProF needs to be set. The device confirms this setting with „- - - - - „
and changes automatically in operation mode. By pressing [P] for approx. 3 seconds
in operation mode, the first menu group InP is shown in the display and thus confirms
the change into the extended parameterisation. It stays activated as long as ULOC or
LOC is entered in menu group RUN.
10
4. Setting up the device
4.3. Extended parametrisation (Professional operation level)
4.3.1. Signal input parameters
Menu group level
Menu level
Menu level
Parameterisation level
Selection of the input signal, TYPE:
There are several measuring input options: 0/4-20 mA or 0-10 VDC signals as works
calibration (without application of the sensor signal) and SenSU (voltage) or SENSA
(current) as sensor calibration (with the sensor applied). Confirm the selection with [P]
and the display switches back to menu level.
Setting the measuring range end value, END:
Set the end value from the smallest to the highest digit with [▲] [▼] and confirm each
digit with [P]. A minus sign can only be parametrized on the highest value digit. After
the last digit, the display switches back to the menu level. If Sens was selected as
input option, you can only select between noca and cal. With noca, only the previously
set display value is taken over, and with cal, the device takes over both the display
value and the analogue input value.
Setting up the measuring range start/offset value, offs:
Enter the start/offset value from the smallest to the highest digit with [▲] [▼] and
confirm each digit with [P]. After the last digit the display switches back to the menu
level. If Sens was selected as input option, you can only select between noca and cal.
With noca, only the previously set display value is taken over, and with cal, the device
takes over both the display value and the analogue input value.
11
4. Setting up the device
Menu level
Parameterisation level
Setting the decimal point, dot:
The decimal point on the display can be moved with [▲] [▼] and confirmed with [P].
The display then switches back to the menu level again.
Setting up the display time, SEC:
then
The display time is set with [▲] [▼]. The display moves up in increments of 0.1 sec up
to 1 sec and in increments of 1.0 sec up to 10.0 sec. Confirm the selection by pressing
the [P] button. The display then switches back to the menu level again.
Rescaling the measuring input values, EndA:
With this function, you can rescale the input value of e.g. 19.5 mA (works setting)
without applying a measuring signal. If sensor calibration has been selected, these
parameters are not available.
Rescaling the measuring input values, OFFA:
With this function, you can rescale the input value of e.g. 3.5 mA (works setting)
without applying a measuring signal. If sensor calibration has been selected, these
parameters are not available.
Setting up the tare/offset value, tArA:
The given value is added to the linerarized value. In this way, the characteristic line
can be shifted by the selected amount.
Setting up the physical unit, UnIt:
One can choose between the above shown physical units. It will be displayed on the
5th digit of the display.
12
4. Setting up the device
Menu level
Parameterisation level
Number of additional setpoints, SPCt:
30 additional setpoints can be defined to the initial- and final value, so linear sensor
values are not linearised. Only activated setpoint parameters are displayed.
Display values for setpoints, dIS.01 … dIS.30:
Under this parameter setpoints are defined according to their value. At the sensor
calibration, like at Endwert/Offset, one is asked at the end if a calibration shall be
activated.
Analog values for setpoints, InP.01 … InP.30:
The setpoints are allways set according to the selected input signal. The desired
analog values can be freely parametrised in ascending order.
Device undercut, dI.Und:
With this function the device undercut (_ _ _ _ _) can be defined on a definite value.
Exception is input type 4-20 mA, it already shows undercut at a signal <1 mA, so a
sensor failure is marked.
Display overflow, dI.OUE:
With this function the display overflow (
_____
) can be defined on a definite value.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „–INP-“.
13
4. Setting up the device
4.3.2. General device parameters
Menu group level
Menu level
Menu level
Parameterisation level
Display time, DISEC:
then
The display is set up with [▲] [▼]. Thereby it jumps until 1 second in increments of 0.1
seconds and until 10.0 seconds in increments of 1.0. With [P] the selection is
confirmed and the device changes into menu level.
Rounding of display values, round:
This function is for instable display values, where the display value is changed in
increments of 1-, 5-, 10- or 50. This does not affect the resolution of the optional
outputs. With [P] the selection is confirmed and the device changes into menu level.
Arithmetic, ArItH:
Root
extraction
Reciprocal
Square
With this function the calculated value, not the measuring value, is shown in the
display. With no, no calulation is deposited. With [P] the selection is confirmed and the
device changes into menu level.
Sliding average determination, AVG:
Here, the number of the meterings that need to be averaged is preset. The time of
averaging results of the product of measuring time SEC and the averaged metering AVG.
With the selection of AVG in the menu level DISPL, the result will be shown in the display
and evaluated via the alarms.
14
4. Setting up the device
Menu level
Parameterisation level
Zero point slowdown, ZErO:
At the zero point tranquilisation, a value range around the zero point can be preset, so
the display shows a zero. If e.g. a 10 is set, the display would show a zero in the
value range from -10 to +10; below continue with -11 and beyond with +11. The
maximum adjustable range of value is 99.
Display, dISPL:
With this function the current measuring value, Min-/Max value, totaliser value or the
process-controlled Hold-value can be allocated to the display. With [P] the selection is
confirmed and the device changes into menu level.
Display flashing, FLASH:
A display flashing can be added as additional alarm function either to single or to a
combination of off-limit condition. With no, no flashing is allocated.
Assignment (deposit) of key functions, tASt:
For the operation mode, special functions can be deposited on the navigation keys
[▲] [▼], in particular this function is made for devices in housing size 48x24 which do
not have a 4th key ([O] key). If the MIN-/MAX-memory is activated with EHtr, all
measured MIN/MAX-values are safed during operation and can be recalled via the
navigation keys. The values get lost by re-start of the device. If the threshold value
correction LI.12 or LI.34 is choosen, the values of the threshold can be changed during
operation without disturbing the operating procedure. With tArA the device is tared to
zero and safed permanently as offset. The device confirms the correct taring by
showing ooooo in the display. Set.tA switches into the offset value and can be changed
via the navigation keys [▲] [▼].
15
4. Setting up the device
Menu level
Parameterisation level
Assignment (deposit) of key functions, tASt :
Via totAL the current value of the totaliser can be displayed for approx.7 seconds, after
this the device jumps back on the parametrised display value. If tot.rE is deposited,
the totaliser can be set back by pressing of the navigation keys [▲] [▼], the device
acknowledges this with ooooo in the display. The configuration of EHt.rE deletes the
MIN/MAX-memory. Under ActuA the measuand is shown for approx. 7s, after this the
display returns to the parametrised display value. If AbS.UA (Absolute value) was
selected, the display shows the value that has been measured since voltage
connection, without consideration of a previous taring. If no is selected, the navigation
keys are without any function in the operation mode.
Special function [O]-key, tASt.4:
…
For the operation mode, special functions can be deposited on the [O]-Taste. This
function is activated by pressing the key. With tArA the device is set temporarily on a
parametrised value. The device acknowledges the correct taring with oo0oo in the
display. Set.tA adds a defined value on to the currently displayed value. Via totAL the
current value of the totaliser can be displayed for approx. 7 seconds, after this the
device jumps back on the parametrised display value. If tot.rE is deposited, the
totaliser can be set back by pressing of the navigation keys [▲] [▼], the device
acknowledges this with ooooo in the display. EHt.rE deletes the MIN/MAX-memory. If
HOLD has been selected, the moment can be hold constant by pressing the [O]-key,
and is updated by releasing the key. Advice: Hold is activated only, if HOLD is selected
under parameter DISPL. ActuA shows the measuring value for approx. 7 seconds, after
this the device switches back on the parametrised display value. The same goes for
AVG, here the sliding average values will be displayed. At AL-1…AL-4 an outout can be
set and therewith e.g. a setpoint adjustment can be done. If no is selected, the [O]-key
is without any function in the operation mode.
16
4. Menu group level
Menu level
Parameterisation level
Special function digital input, dIG.In:
…
In operation mode, the above shown parameter can be laid on the optional digital
input, too. Function description see tASt.4.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „– fct –“.
17
4. Setting up the device
4.3.3. Safety parameters
Menu group level
Menu level
Menu level
Parameterisation level
User code U.Code:
Via this code reduced sets of parameters can be set free. A change of the U.CodE can
be done via the correct input of the A.CodE (master code).
Master code, A.Code:
By entering A.CodE the device will be unlocked and all parameters are released.
Release/lock analog output parameter, Out.LE:
Analog output parameter can be locked or released for the user:
- At En-oF the initial or final value can be changed in operation mode.
- At Out.EO the output signal can be changed from e.g. 0-20mA to 4-20mA or 0-10VDC.
- At ALL analog output parameters are released.
- At no all analog output parameters are locked.
18
4. Setting up the device
Menu level
Parameterisation level
Release/lock alarm parameters, AL.LEU:
This parameter describes the user relase/user lock of the alarm.
- LIMIt, here only the range of value of the threshold values 1-4 can be changed.
- ALrM.L, here the range of value and the alarm trigger can be changed.
- ALL, all alarm parameters are released.
- no, all alarm parameters are locked.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „– COD –“.
4.3.4. Serial parameters
Menu group level
Menu level
Menu level
Parameterisation level
Device address, ADDR:
The device address is adjusted from the smallest to the largest digit with the
navigation keys [▲] [▼] and confirmed digit per digit with [P]. A device address up to
max. 250 is available.
ModBus operation type, b.mode:
19
4. Setting up the device
Menu level
Parameterisation level
Timeout, tIout:
The monitoring of the data transfer is parameterized in seconds up to max. 100
seconds; there is no monitoring with an input of 000. The timeout is adjusted from the
smallest to the largest digit with the navigation keys [▲] [▼] and confirmed digit per
digit with [P]. After the last digit the device changes back into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level
„– SER –“.
4.3.5. Analog output parameters for analog output 1
Menu group level
Menu level
Menu level
Parameterisation level
Selection reference of analog output, OutPt:
The analog output signal can refer to different functions, in detail these are the current
measurand, the min-value, the max-value or the totaliser-/sum function. If HoLd is
selected, the signal of the analog output will be kept. It can be continued processing
after a deactivation of Hold. With [P] the selection is confirmed and the device
changes into menu level.
Selection analog output, Out.rA:
Three output signals are available 0-10 VDC, 0-20 mA and 4-20 mA. Select the
desired signal with this function.
20
4. Setting up the device
Menu level
Parameterisation level
Setting the final value of the analog output, Out.En:
The final value is adjusted from the smallest to the highest digit with [▲] [▼] and
confirmed digit per digit with [P]. A minus sign can only be parameterized on the
highest digit. After the last digit the device changes back into menu level.
Setting the initial value of the analog output, Out.OF:
The initial value is adjusted from the smallest to the highest digit with [▲] [▼] and
confirmed digit per digit with [P]. A minus sign can only be parameterized on the
highest digit. After the last digit the device changes back into menu level.
Overflow behaviour, O.FLoU:
To recognise and evaluate faulty signals, e.g. by a controller, the overflow behaviour
of the analog output can be defined. As overflow can be seen either EdGE, that means
the analog output runs on the set limits e.g. 4 and 20 mA, or to.OFF (input value smaller
than initial value, analog output jumps on e.g. 4 mA), to.End (higher than final value,
analog output jumps on e.g. 20 mA). If to.MIn or to.MAX is set, the analog output jumps
on the smallest or highest possible binary value. This means that values of e.g. 0 mA,
0 VDC or values higher than 20 mA or 10 VDC can be reached. With [P] the selection
is confirmed and the device changes into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „– out –“.
21
4. Setting up the device
4.3.6. Analog output parameters for analog output 2
Menu group level
Menu level
Menu level
Parameterisation level
Selection reference of analog output, Ou2Pt:
The analog output signal can refer to different functions, in detail these are the current
measurand, the min-value, the max-value or the totaliser-/sum function. If HoLd is
selected, the signal of the analog output will be kept. It can be continued processing
after a deactivation of Hold. With [P] the selection is confirmed and the device
changes into menu level.
Selection analog output, Ou2.rA:
3 output signals are available 0-10 VDC, 0-20 mA and 4-20 mA. Select the desired
signal with this function.
Setting the final value of the analog output, Ou2.En:
The final value is adjusted from the smallest to the highest digit with [▲] [▼] and
confirmed digit per digit with [P]. A minus sign can only be parameterized on the
highest digit. After the last digit the device changes back into menu level.
22
4. Setting up the device
Menu level
Parameterisation level
Setting the initial value of the analog output, Ou2.En:
The initial value is adjusted from the smallest to the highest digit with [▲] [▼] and
confirmed digit per digit with [P]. A minus sign can only be parameterized on the
highest digit. After the last digit the device changes back into menu level.
Overflow behaviour, Ou2.fl:
To recognise and evaluate faulty signals, e.g. by a controller, the overflow behaviour
of the analog output can be defined. As overflow can be seen either EdGE, that means
the analog output runs on the set limits e.g. 4 and 20 mA, or to.OFF (input value smaller
than initial value, analog output jumps on e.g. 4 mA), to.End (higher than final value,
analog output jumps on e.g. 20 mA). If to.MIn or to.MAX is set, the analog output jumps
on the smallest or highest possible binary value. This means that values of e.g. 0 mA,
0 VDC or values higher than 20 mA or 10 VDC can be reached. With [P] the selection
is confirmed and the device changes into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–
ou2 –“.
23
4. Setting up the device
4.3.7. Relay functions
Menu group level
Menu level
Menu level
Parameterisation level
Alarm relay 1, rEL-1:
The same applies for relays 2-4
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be
inserted at activated alarms Al-1/4 or de-activated alarms Aln1/4. If LOGIC is selected,
logical links are available in the menu level Log-1 and Com-1. One can only get to these
two menu levels via LOGic, at all other selected functions, these two parameters are
overleaped. Via On/OFF the setpoints can be activated/de-activated, in this case the
output and the setpoint display are set/not set on the front of the device. With [P] the
selection is confirmed and the device changes into menu level.
Logic relay 1, Log-1
Here, the switching behaviour of the relay is defined via a logic link, the following
schema describes these functions with inclusion of AL-1 and AL-2:
A1 v A2
____ _ _
As soon as a selected alarm is activated, the
relay operates. Equates to operating current
principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms
are active.
____ _ _
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
With [P] the selection is confirmed and the device changes into menu level.
24
4. Setting up the device
Menu level
Parameterisation level
Alarms for relay 1, CoM-1:
….
The allocation of the alarms to relay 1 happens via this parameter, one alarm or a
group of alarms can be chosen. With [P] the selection is confirmed and the device
changes into menu level.
Alarm relay 5, reL-5:
The same applies for relays 6-8
….
….
Each setpoint (optional) can be linked up via 4 alarms (by default). This can either be
inserted at activated alarms AL1/4 or de-activated alarms ALN1/4. If LOGIC is selected,
logical links are available in the menu level LoG-1 and CoM-1. One can only get to these
two menu levels via LOGIC, at all other selected functions, these two parameters are
overleaped. Via On/OFF the setpoints can be activated/de-activated, in this case the
output and the setpoint display are set/not set on the front of the device. With [P] the
selection is confirmed and the device changes into menu level.
Logic relay 5, LoG-5:
Here, the switching behaviour of the relay is defined via a logic link, the following
schema describes these functions with inclusion of AL-1 and AL-2:
A1 v A2
____ _ _
As soon as a selected alarm is activated, the
relay operates. Equates to operating current
principle.
A1 v A2 = A1 Λ A2
The relay operates only, if no selected alarm is
active. Equates to quiescent current principle.
A1 Λ a2
The relay operates only, if all selected alarms
are active.
____ _ _
A1 Λ A2 = A1 v A2
As soon as a selected alarm is not activated, the
relay operates.
With [P] the selection is confirmed and the device changes into menu level.
25
4. Setting up the device
Menu level
Parameterisation level
Alarms for relay 5, CoM-5:
….
The allocation of the alarms to relay 5 happens via this parameter, one alarm or a
group of alarms can be chosen. With [P] the selection is confirmed and the device
changes into menu level.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–
rel –“.
4.3.8. Alarm parameters
Menu group level
Menu level
Menu level
Parameterisation level
Dependency alarm1, ALrM.1:
The dependency of alarm 1 can be related to special functions, in detail these are the
current measuring value, the MIN-value, the MAX-value or the totaliser-/sum-value. Is
Hold selected, then the alarm is hold and processed just after deactivation of HOLD.
EHtEr causes the dependency either by pressing the [O]-key on the front of the
housing or by an external signal via the digital input. With [P] the selection is
confirmed and the device changes into menu level.
26
4. Setting up the device
Menu level
Parameterisation level
Threshold values / Limit values, LI-1:
The limit value defines the threshold, that activates/deactivates an alarm.
Hysteresis for Threshold values, HY-1:
The delayed reaction of the alarm is the difference to the threshold value, which is
defined by the hysteresis.
Function for threshold value undercut /exceedance, Fu-1:
A limit value undercut is selected with Louu (for LOW = lower limit value), a limit value
exceedance with High (for HIGH = higher limit value). If e.g. limit value 1 is on a
threshold level of 100 and allocated with function High, an alarm is activated by
reaching of the threshold level. If the threshold value was allocated to Low, an alarm
will be activated by undercutting the threshold value, as long as the hysteresis is zero.
Switching-on delay, ton-1:
For limit value 1 one can preset a delayed switching-on of 0-100 seconds.
Switching-off delay, toF-1:
For limit value 1 one can preset a delayed switching-off of 0-100 seconds.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group level „–
Al1 –“.
The same applies for –Al2– to –Al8–.
27
4. Setting up the device
4.3.9. Totaliser (Volume metering)
Menu group level
Menu level
Menu level
Parameterisation level
Totaliser state, total:
The totaliser makes measurements on a time base of e.g. l/h possible, at this the
scaled input signal is integrated by a time and steadily (select Stead) or temporarily
(select temp) safed. If Off is selected, the function is de-activated. With [P] the
selection is confirmed and the device changes into menu level.
Time base, t.base:
Under this parameter the time base of the measurement can be preset in seconds,
minutes or hours.
Totaliser factor, Facto:
…
At this the factor (100…106) respectively the divisor for the internal calculation of the
measuring value is assigned.
Setting up the decimal point for the totaliser, tot.dt:
The decimal point of the device can be adjusted with the navigation keys [▲] [▼].
With [P] the selection is confirmed and the device changes into menu level.
28
4. Setting up the device
Menu level
Parameterisation level
Totaliser reset, tot.re:
The reset value is adjusted from the smallest to the highest digit with the navigation
keys [▲] [▼] and digit per digit confirmed with [P]. After the last digit, the display
switches back to the menu level. The activator for the reset is parameter driven via the
4th key or via the optional digital input.
Back to menu group level, rEt:
With [P] the selection is confirmed and the device changes into menu group
level „– tot –“ .
4.3.10. Programming interlock, run:
Menu group level
Description see page 11, menu level run
29
4. Setting up the device
4.4. Alarms / Relays
This device has 4 virtual alarms that can monitor one limit value in regard of an undercut or
exceedance. Each alarm can be allocated to an optional relay output S1-S2; furthermore
alarms can be controlled by events like e.g. Hold or Min-/Max-value.
Function principle of alarms / relays
Alarm / Relay x
Deactivated, instantaneous value, Min-/Max-value, Hold-value,
totaliser value
Switching threshold
Threshold / limit value of the change-over
Hysteresis
Broadness of the window between the switching thresholds
Working principle
Operating strom / Quiescent current
Operating current
By operating current the alarm S1-S2 is
off below the threshold and on on
reaching the threshold.
Quiescent current
By quiescent current the alarm S1-S2 is
on below the threshold and switched off
on reaching the threshold.
Switching-on delay
The switching-on delay is activated via
an alarm and e.g. switched 10 seconds
after reaching the switching threshold, a
short-term exceedance of the switching
value does not cause an alarm,
respectively does not cause a switching
operation of the relay. The switching-off
delay operates in the same way, keeps
the alarm / the relay switched longer for
the parametrised time.
30
5. Factory settings
5. Factory settings
5.1. Default values
Standard parametrization (flat operation level)
Parameter
Type of input
Menu items
0…10 V
Default values
0…20 mA
4…20 mA
Sensor
calibration V
Sensor
calibration A
Sensor
calibration V
to
Final value
to
Offset
to
Decimal point
to
Measuring
time
0.1 second
Analog output
range
0…10 V
0…20 mA
10.0 seconds
1.0 seconds
4…20 mA
4…20 mA
to
Analog output
final value
to
Analog output
initial value
to
Limit value 1
to
Hysteresis 1
Operation type
1
Undercut
Exceedance
Exceedance
to
Limit value 2
31
5. Factory settings
Parameter
Default values
Menu items
to
Hysteresis 2
Operation type
2
Undercut
Exceedance
Exceedance
to
User code
to
Master code
run
Standard
operation
Parameter
lock
Standard
operation
Professional
operation
Extended parametrisation (professional operation flat level)
Signal input parameters
Parameter
Type of input
Default values
Menu items
0…10 V
0…20 mA
4…20 mA
Sensor
calibration V
Sensor
calibration A
Sensor
calibration V
to
Final value
to
Offset
to
Decimal point
to
Measuring
time
0.1 seconds
10.0 Seconds
to
Analog
final value
32
1.0 seconds
5. Factory settings
Parameter
Default values
Menu items
to
Analog
final value
to
Display
offset
Display
unit
Exceedance
none
°C
°F
L
to
Number of
setpoints
to
Display value
1
to
Analog value
1
…
to
Display value
30
to
Analog value
30
to
Display
underflow
to
Display
overflow
33
A
U
t
none
5. Factory settings
General device parameters
Parameter
Default values
Menu items
to
Display time
0.1 seconds
10 seconds
1 second
Round a value
no rounding
in steps of 5
in steps of 10
in steps of 50
no rounding
Arithmetic
none
reciprocal
value
root extraction
squaring down
none
to
Sliding
average value
to
Zero point
tranquilisation
no
tranquilisation
Default display
Current
measurand
at x-digit
display = zero
no
tranquilisation
Minimum
Maximum
Totaliser
Hold
Current
measurand
no
Alarm 1
Alarm 2
Alarm 1 + 2
Alarm 3
no
Alarm 4
Alarm 3 + 4
Alarm 1…4
Sliding
average value
Flashing at
34
5. Factory settings
Parameter
Functions Up/Down-key
Special
function
4th key
Digital input
Default values
Menu items
no
Extremum
(min/max)
Alarm limit
1+2
Alarm limit
3+4
Tara function
Set tara value
Totaliser value
Totaliser reset
Extremum
reset
Display
measurand
no
Tara function
Set tara value
Totaliser value
Totaliser
reset
Extremum
reset
Display
measurand
Hold
Sliding
average value
Alarm 1
Alarm 2
Alarm 3
Alarm 4
no
Tara function
Set tara value
Totaliser value
Totaliser
reset
Extremum
reset
Display
measurand
Hold
Sliding
average value
Alarm 1
Alarm 3
Alarm 3
Alarm 4
35
no
no
no
5. Factory settings
Safety parameters
Parameter
Default values
Menu items
to
User code
to
Administrator
code
Analog output
level
Not
changeable
Range of
value
Alarm level
Not
changeable
Limit value
Range of
value &
source
Range of
value &
source
All parameters
All parameters
All
parameters
All
parameters
Serial parameters
Parameter
Default values
Menu items
to
Device
address
Communication mode
ASCII
rtu
ASCII
to
Timeout
No monitoring
X seconds no
traffic
36
No monitoring
5. Factory settings
Analog output parameters 1
Parameter
Source
Default values
Menu items
Current
measurand
Minimum
Maximum
Totaliser
0...20 mA
4...20 mA
x seconds
no traffic
Hold
Current
measurand
Sliding
average value
Output range
0...10 mA
4...20 mA
to
Final value
to
Initial value
Overflow
behaviour
Run to
threshold
value
Switch to final
value
Switch to start
37
Switch to
smallest value
Switch to
highest value
Run to
threshold
value
5. Factory settings
Analog output parameter 2
Parameter
Source
Default values
Menu items
Current
measurand
Minimum
Maximum
Totaliser
4...20 mA
x seconds
no traffic
Hold
Current
measurand
Sliding
average value
Output range
0...10 mA
0...20 mA
4...20 mA
to
Final value
to
Initial value
Overflow
behaviour
Run to
threshold
value
Switch to final
value
Switch to start
38
Switch to
smallest value
Switch to
highest value
Run to
threshold
value
5. Factory settings
Relay functions
Parameter
Menu items
Default values
to
Relay
function1
at alarm 1
at alarm 4
at alarm 1
to
not alarm 1
not alarm 4
via logic
declined
activated
Logic relay 1
active if at
least 1 alarm
active if no
alarm
active
if all alarms
active
if not at least 1
alarm
Alarm combination relay 1
Alarm 1
Alarm 2
Alarm 1 + 2
Alarm 3
etc. up to
Alarm
1+2+3+4
active if at
least 1 alarm
Alarm 1 + 3
Alarm 1
to
Relay function
2
at alarm 1
at alarm 4
at alarm 2
to
not alarm 1
not alarm 4
via logic
declined
activated
Logic relay 2
active if at
least 1 alarm
active if no
alarm
active
if all alarms
active
if at least 1
alarm not
Alarm combination relay 2
Alarm 1
Alarm 2
Alarm 1+2
Alarm 3
to
Alarm
1+2+3+4
39
active if at
least 1 alarm
Alarm 1+3
aktive if at
least 1 alarm
5. Factory settings
Parameter
Default values
Menu items
to
Relay function
3
at alarm 4
at alarm 1
at alarm 1
to
not alarm 4
not alarm 1
via logic
declined
activated
Logic relay 3
active if at
least 1 alarm
active if no
alarm
active
if all alarms
active
if not at least 1
alarm
Alarm combination relay 3
Alarm 1
Alarm 2
Alarm 1 + 2
Alarm 3
etc. up to
Alarm
1+2+3+4
active if at
least 1 alarm
Alarm 1 + 3
Alarm 1
to
Relay function
4
at alarm 4
at alarm 1
at alarm 3
to
not alarm 4
not alarm 1
via logic
declined
activated
Logic relay 4
active if at
least 1 alarm
active if no
alarm
active
if all alarms
active
if not at least 1
alarm
Alarm combination relay 4
Alarm 1
Alarm 2
Alarm 1 + 2
Alarm 3
etc. up to
Alarm
1+2+3+4
40
active if at
least 1 alarm
Alarm 1 + 3
Alarm 1
5. Factory settings
Parameter
Default values
Menu items
to
Relay function
5
at alarm 4
at alarm 1
at alarm 1
to
not alarm 4
not alarm 1
via logic
declined
activated
Logic relay 5
active if at
least 1 alarm
active if no
alarm
active
if all alarms
active
if not at least 1
alarm
Alarm combination relay 5
Alarm 1
Alarm 2
Alarm 1 + 2
Alarm 3
etc. up to
Alarm
1+2+3+4
active if at
least 1 alarm
Alarm 1 + 3
Alarm 1
to
Relay function
6
at alarm 4
at alarm 1
at alarm 3
to
not alarm 4
not alarm 1
via logic
declined
activated
Logic relay 6
active if at
least 1 alarm
active if no
alarm
active
if all alarms
active
if not at least 1
alarm
Alarm combination relay 6
Alarm 1
Alarm 2
Alarm 1 + 2
Alarm 3
etc. up to
Alarm
1+2+3+4
41
active if at
least 1 alarm
Alarm 1 + 3
Alarm 1
5. Factory settings
Parameter
Default values
Menu items
to
Relay function
7
at alarm 4
at alarm 1
at alarm 1
to
not alarm 4
not alarm 1
via logic
declined
activated
Logic relay 7
active if at
least 1 alarm
active if no
alarm
active
if all alarms
active
if not at least 1
alarm
Alarm combination relay 7
Alarm 1
Alarm 2
Alarm 1 + 2
Alarm 3
etc. up to
Alarm
1+2+3+4
active if at
least 1 alarm
Alarm 1 + 3
Alarm 1
to
Relay function
8
at alarm 4
at alarm 1
at alarm 3
to
not alarm 4
not alarm 1
via logic
declined
activated
Logic relay 8
active if at
least 1 alarm
active if no
alarm
active
if all alarms
active
if not at least 1
alarm
Alarm combination relay 8
Alarm 1
Alarm 2
Alarm 1 + 2
Alarm 3
etc. up to
Alarm
1+2+3+4
42
active if at
least 1 alarm
Alarm 1 + 3
Alarm 1
5. Factory settings
Alarm parameters
Parameter
Alarm source
1
Default values
Menu items
Current
measurand
Minimum
measurand
Sliding
average value
External input
(DigIn/Tast4)
Maximum
measurand
Totaliser
Hold
Current
measurand
to
Limit value 1
to
Hysteresis 1
Function 1
Undercut
Exceedance
Exceedance
to
Activation
delay 1
none
100 seconds
none
100 seconds
none
to
Deactivation
delay 1
none
43
5. Factory settings
Parameter
Alarm source
2
Default values
Menu items
Current
measurand
Minimum
measurand
Sliding
average value
External input
(DigIn/Tast4)
Maximum
measurand
Totaliser
Hold
Current
measurand
to
Limit value 2
to
Hysteresis 2
Function 2
Undercut
Exceedance
Exceedance
to
Activation
delay 2
none
100 seconds
none
100 seconds
none
to
Deactivation
delay 2
Parameter
Alarm source
3
none
Default values
Menu items
Current
measurand
Minimum
measurand
Sliding
average value
External input
(DigIn/Tast4)
Maximum
measurand
to
Limit value 3
to
Hysteresis 3
44
Totaliser
Hold
Current
measurand
5. Factory settings
Parameter
Function 3
Default values
Menu items
Undercut
Exceedance
Exceedance
to
Activation
delay 3
none
100 seconds
none
100 seconds
none
to
Deactivation
delay 3
Parameter
Alarm source
4
none
Default values
Menu items
Current
measurand
Minimum
measurand
Sliding
average value
External input
(DigIn/Tast4)
Maximum
measurand
Totaliser
Hold
Current
measurand
to
Limit value 4
to
Hysteresis 4
Function 4
Undercut
Exceedance
Exceedance
to
Activation
delay 4
none
100 seconds
none
100 seconds
none
to
Deactivation
delay 4
none
45
5. Factory settings
Alarm parameters
Parameter
Alarm source
5
Default values
Menu items
Current
measurand
Minimum
measurand
Sliding
average value
External input
(DigIn/Tast4)
Maximum
measurand
Totaliser
Hold
Current
measurand
to
Limit value 5
to
Hysteresis 5
Function 5
Undercut
Exceedance
Exceedance
to
Activation
delay 5
none
100 seconds
none
100 seconds
none
to
Deactivation
delay 5
none
46
5. Factory settings
Parameter
Alarm source
6
Default values
Menu items
Current
measurand
Minimum
measurand
Sliding
average value
External input
(DigIn/Tast4)
Maximum
measurand
Totaliser
Hold
Current
measurand
to
Limit value 6
to
Hysteresis 6
Function 6
Undercut
Exceedance
Exceedance
to
Activation
delay 6
none
100 seconds
none
100 seconds
none
to
Deactivation
delay 6
Parameter
Alarm source
7
none
Default values
Menu items
Current
measurand
Minimum
measurand
Sliding
average value
External input
(DigIn/Tast4)
Maximum
measurand
to
Limit value 7
to
Hysteresis 7
47
Totaliser
Hold
Current
measurand
5. Factory settings
Parameter
Function 7
Default values
Menu items
Undercut
Exceedance
Exceedance
to
Activation
delay 7
none
100 seconds
none
100 seconds
none
to
Deactivation
delay 7
Parameter
Alarm source
8
none
Default values
Menu items
Current
measurand
Minimum
measurand
Sliding
average value
External input
(DigIn/Tast4)
Maximum
measurand
Totaliser
Hold
Current
measurand
to
Limit value 8
to
Hysteresis 8
Function 8
Undercut
Exceedance
Exceedance
to
Activation
delay 8
none
100 seconds
none
100 seconds
none
to
Deactivation
delay 8
none
48
5. Factory settings
Totaliser (Volume metering)
Parameter
Default values
Menu items
Totaliser state
Off
Permanent
storage
Loose
storage
Off
Time base
Seconds
Minutes
Hours
Seconds
10^6
10^0=1
to
Divisor
10^0=1
to
Decimal
places
to
Totaliser
Reset
5.2. Reset to default values
To return the unit to a defined basic state, a reset can be carried out to the default values.
The following procedure should be used:
• Switch off the power supply
• Press button [P]
• Switch on voltage supply and press [P]-button until „- - - - -“ is shown in the display.
With reset, the default values of the program table are loaded and used for subsequent
operation. This puts the unit back to the state in which it was supplied.
Caution! All application-related data are lost.
49
6. Technical data
6. Technical data
Housing
Dimensions
96x48x120 mm (BxHxD)
96x48x139 mm (BxHxD) incl. plug-in terminal
Panel cut-out
92.0+0,8 x 45.0+0,6 mm
Wall thickness
to 15 mm
Fixing
screw elements
Material
PC Polycarbonate, black, UL94V-0
Sealing material
EPDM, 65 Shore, black
Protection class
standard IP65 (Front), IP00 (Back side)
Weight
approx. 300 g
Connection
plug-in terminal; wire cross section up to 2.5 mm2
Display
Digit height
14 mm
Segment colour
red (optional blue/green/orange)
Range of display
-19999 to 99999
Setpoints
one LED per setpoint
Overflow
horizontal bars at the top
Underflow
horizontal bars at the bottom
Display time
0.1 to 10.0 seconds
Input
Measuring range
Ri
Measuring error
Digit
min -22…max 24 mA
0/4-20 mA
100 Ω
0.1 % of measuring range
±1
min -12…max 12 VDC
0…10 VDC
100 kΩ
0.1 % of measuring range
±1
Digital input
< 2,4 V OFF, 10 V ON, max. 30 VDC
RI ~ 5 kΩ
Accuracy
Temperature drift
100 ppm / K
Measuring time
0.1…10.0 seconds
Measuring principle
U/F-converter
Resolution
approx. 18 Bit at 1s measuring time
50
6. Technical data
Output
Sensor supply
24 VDC / 50 mA; 10 VDC / 20 mA
Analog output
0/4-20 mA or 0-10 VDC 16 Bit switchable
Switching outputs
Relay with change-over contacts
Switching cycles
250 VAC / 5 AAC; 30 VDC / 5 ADC
30 x 103 at 5 AAC, 5 ADC ohm resistive load
10 x 106 mechanically
Diversity according to DIN EN50178
/ Characteristics according to DIN EN60255
PhotoMos outputs
8 normally open (NO) contacts 30 VDC/AC, 0,4 A
Power supply
230 VAC +/- 10 % max. 10 VA
10-30 VDC galv. insulated, max. 4 VA
Memory
EEPROM
Data life
≥ 100 years
Ambient conditions
Working temperature
0…50°C
Storing temperature
-20…80°C
Climatic density
relative humidity 0-80% on years average without dew
EMV
EN 61326
CE-sign
Conformity to directive 2004/108/EG
Safety standard
EN 61010; EN 60664-1
51
7. Safety advices
7. Safety advices
Please read the following safety advice and the assembly chapter 1 before installation
and keep it for future reference.
Proper use
The M3-device is designed for the evaluation and display of sensor signals.
Danger! Careless use or improper operation can result in
personal injury and/or damage to the equipment.
Control of the device
The panel meters are checked before dispatch and sent out in perfect condition. Should
there be any visible damage, we recommend close examination of the packaging. Please
inform the supplier immediately of any damage.
Installation
The M3-device must be installed by a suitably qualified specialist (e.g. with a
qualification in industrial electronics).
Notes on installation
• There must be no magnetic or electric fields in the vicinity of the device, e.g. due to
transformers, mobile phones or electrostatic discharge.
• The fuse rating of the supply voltage should not exceed a value of 6A N.B. fuse.
• Do not install inductive consumers (relays, solenoid valves etc.) near the device and
suppress any interference with the aid of RC spark extinguishing combinations or freewheeling diodes.
• Keep input, output and supply lines separate from one another and do not lay them
parallel with each other. Position “go” and “return lines” next to one another. Where
possible use twisted pair. So, you receive best measuring results.
• Screen off and twist sensor lines. Do not lay current-carrying lines in the vicinity. Connect
the screening on one side on a suitable potential equaliser (normally signal ground).
• The device is not suitable for installation in areas where there is a risk of explosion.
• Any electrical connection deviating from the connection diagram can endanger human life
and/or can destroy the equipment.
• The terminal area of the devices is part of the service. Here electrostatic discharge needs
to be avoided. Attention! High voltages can cause dangerous body currents.
• Galvanic insulated potentials within one complex need to be placed on a appropriate point
(normally earth or machines ground). So, a lower disturbance sensibility against impacted
energy can be reached and dangerous potentials, that can occur on long lines or due to
faulty wiring, can be avoided.
52
8. Error elimination
8. Error elimination
Error description
Measures
1.
The unit permanently indicates
overflow.
• The input has a very high measurement, check
the measuring circuit.
• With a selected input with a low voltage signal, it
is only connected on one side or the input is open.
• Not all of the activated setpoints are
parameterised. Check if the relevant parameters
are adjusted correctly.
2.
The unit permanently shows
underflow.
• The input has a very low measurement, check the
measuring circuit .
• With a selected input with a low voltage signal, it
is only connected on one side or the input is open.
• Not all of the activated setpoints are
parameterised. Check if the relevant parameters
are adjusted correctly.
3.
The word "HELP " lights up in the
7-segment display.
• The unit has found an error in the configuration
memory. Perform a reset on the default values
and re-configure the unit according to your
application.
4.
Program numbers for parameterising
of the input are not accessible.
• Programming lock is activated
• Enter correct code
5.
"Err1" lights up in the 7-segment
display
• Please contact the manufacturer if errors of this
kind occur.
6.
The device does not react as
expected.
• If you are not sure if the device has been
parameterised before, then follow the steps as
written in chapter 5.2. and set it back to its
delivery status.
53
M3_11GB.pdf
Stand: 13.07.2011
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement