HFX 100 Series Setup Guide

HFX 100 Series Setup Guide
HFX 100 Series • Setup Guide
The Extron HFX 100 Series consists of a transmitter (HFX 100 Tx) and receiver (HFX 100 Rx)
that use one multimode fiber optic cable to extend a HDMI signal up to 984 feet (300 m).
This guide provides basic instructions for an experienced installer to set up and operate the
HFX 100 Series extender (see the HFX 100 Series User Guide, at www.extron.com, for full
instructions).
Installation
Step 1 — Mounting
Mount the HFX 100 Tx close to the HDMI source and the HFX 100 Rx close to the HDMI display
device. See the HFX 100 Series User Guide for all mounting options. Follow the instructions
provided with the appropriate installation kit.
Step 2 — Cable Connections
HFX 100 Series Front Panel
HFX 100 Tx Rear Panel
b
d
a
POWER
POWER
12V
12V
0.3
0.3 A
A MAX
MAX
HFX
HFX 100
100 Tx
Tx
HFX 100 Rx Rear Panel
POWER
POWER
12V
12V
0.2
0.2 A
A MAX
MAX
HFX 100 Rx
OUTPUT
OUTPUT
INPUT
INPUT
INPUT
INPUT
OUTPUT
OUTPUT
Extron
c
b
f
e
1. Connect one of the provided 12 VDC power supplies to the front panel captive screw
connectors of the transimtter and the other to the receiver (b).
ATTENTION: Before connecting power to the HFX 100 Tx or Rx, see the attention
box in the “Power Supply” section of the HFX 100 Series User Guide for important
information about power supplies.
NOTES:
• When the units receive power but no input signals, the front panel LED (a) lights
amber.
• When the transmitter receives power and a HDMI input signal, the front panel LED
lights green
• When the receiver receives power and a fiber optic input signal, the front panel LED
lights green.
HFX 100 Series • Setup Guide (Continued)
2. Connect the HFX 100 Tx output (d) to the HFX 100 Rx input (f) using one multimode
fiber optic cable (not provided).
WARNING: Possible Damage to Eyesight. The HFX 100 Series extender outputs
continuous invisible light (Class 1 rated), which may be harmful and dangerous
to the eyes; use with caution. Do not look into the rear panel fiber optic cable
connector or into the fiber optic cable itself. Plug the attached dust cap into the
optical transceiver when the fiber optic cable is unplugged.
3. Connect the HDMI display to the HDMI output connector of the HFX 100 Rx (e). Power on
the display.
4. Connect the HDMI source to the HDMI input connector of the HFX 100 Tx (c). Power on
the HDMI source.
Application Diagram
Extron
HFX 100 Tx
Transmitter
00
X1
HF
Tx
WER
PO
V
12 MAX
A
--
UT
TP
OU
T
PU
IN
Up to 300m ( 984 ft )
on Multimode Fiber
HDMI
FL
SE
/CLO
OFF
Extron
HFX 100 Rx
Receiver
USB
OPEN
I
HDM
PQLS
BY/ON
STAND
Blu-ray Player
00
X1
HF
WER
PO
V
12 MAX
A
--
Rx
T
PU
IN
UT
TP
OU
HDMI
Flat Panel Display
Extron Headquarters
+800.633.9876 Inside (USA/Canada Only)
Extron USA - West
Extron USA - East
+1.714.491.1500+1.919.850.1000
FAX:
+1.714.491.1517+1.919.850.1001
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
FAX:
+31.33.453.4050
Extron Asia
+65.6383.4400
FAX:
+65.6383.4664
Extron Japan
+81.3.3511.7655
FAX:
+81.3.3511.7656
Extron China
+86.21.3760.1568
FAX:
+86.21.3760.1566
Extron Middle East
+971.4.299.1800
FAX:
+971.4.299.1880
© 2013 Extron Electronics All rights reserved. www.extron.com
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
FAX:
+91.80.3055.3737
Extron Korea
+82.2.3444.1571
FAX: +82.2.3444.1575
68-2260-50 Rev A 04 13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement