Motorola VT1000v User guide

Motorola VT1000v User guide
VT1000User.book Page i Monday, November 3, 2003 4:19 PM
User Guide
Title
VT1000v Series
Voice Terminal
Important
This guide contains information related to
product warranty, regulatory matters, and
software licenses.
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page ii Monday, November 3, 2003 4:19 PM
Safety and Regulatory Information
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS DEVICE TO RAIN OR MOISTURE. THE DEVICE SHALL NOT
BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE DEVICE.
CAUTION: TO ENSURE REGULATORY AND SAFETY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES. TO
PREVENT ELECTRICAL SHOCK, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS
THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
CAUTION: DO NOT OPEN THE UNIT. DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE INSTALLATION AND
TROUBLESHOOTING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO. REFER ALL SERVICING TO QUALIFIED SERVICE
PERSONNEL.
It is recommended that the customer install an AC surge arrestor in the AC outlet to which this device is connected. This is to avoid damaging the
equipment by local lightning strikes and other electrical surges.
This product was qualified under test conditions that included the use of the supplied cable between system components. To be in
compliance with regulations, the user must use this cable and install it properly.
Different types of cord sets may be used for connections to the main supply circuit. Use only a main line cord that complies with all
applicable product safety requirements of the country of use.
Installation of this product must be in accordance with national wiring codes.
To prevent overheating, do not block the ventilation holes on the sides of the Motorola voice terminal.
Wipe the Motorola voice terminal with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray cleaners directly on the unit or
use forced air to remove dust.
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page iii Monday, November 3, 2003 4:19 PM
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
■
Re-orient or relocate the receiving antenna
■
Increase the separation between the equipment and receiver
■
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■
Consult the dealer or an experienced radio/TV technician for help.
Changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Canadian Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la
classe B respects toutes les exigences du Règlement sur le matériel brouilleur du Canada.
FCC Declaration of Conformity
According to 47CFR, Parts 2 and 15 for Class B Personal Computers and Peripherals; and/or CPU Boards and Power Supplies used with Class B
Personal Computers, Motorola BCS, 101 Tournament Drive, Horsham, PA 19044, 1-215-323-1000, declares under sole responsibility that the product
identifies with 47CFR Part 2 and 15 of the FCC Rules as a Class B digital device. Each product marketed is identical to the representative unit tested
and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within
the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR 2.909. Operation is subject to the
following condition: This device must accept any interference received, including interference that may cause undesired operation. The above
named party is responsible for ensuring that the equipment complies with the standards of 47CFR, Paragraph 15.101 to 15.109.
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page iv Monday, November 3, 2003 4:19 PM
International Declaration of Conformity
We, Motorola, Inc. Broadband Communications Sector
101 Tournament Drive
Horsham, PA, U.S.A.
declare under our sole responsibility that the:
Motorola VT1003v and VT1005v voice terminals
to which this declaration relates is in conformity with one or more of the following standards:
EN55022
EN55024
ETSI EN300 386 CISPR-22
EN60065
EN60825
EN60950
CISPR-24
IEC 60950
the following provisions of the Directive(s) of the Council of the European Union:
EMC Directive 89/336/EEC
Low Voltage Directive 73/23/EEC
Directive 93/68/EEC
Copyright © 2003 by Motorola, Inc.
All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as translation, transformation or adaptation)
without written permission from Motorola, Inc.
Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to provide notification of such revision or
change. Motorola provides this guide without warranty of any kind, either implied or expressed, including, but not limited to, the implied warranties of merchantability and fitness for a
particular purpose. Motorola may make improvements or changes in the product(s) described in this manual at any time.
MOTOROLA, the Stylized M Logo, and SURFboard are registered in the US Patent & Trademark Office. Microsoft, Windows, Windows Me and Windows XP are either registered trademarks
or trademarks of Microsoft Corporation in the United States and/or other countries. Microsoft Windows screen shots are used by permission of Microsoft Corporation. Macintosh is a
registered trademark of Apple Computer, Inc. Netscape Navigator is a registered trademark of Netscape Communications Corporation. UNIX is a registered trademark of the Open Group in
the United States and other countries. All other product or service names are the property of their respective owners. © Motorola, Inc. 2003.
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page vi Monday, November 3, 2003 4:19 PM
Contents
Introduction ..............................................................................................................................1
Sample Configuration Without A Home Network ............................................................................... 2
Sample Configuration With A Home Network .................................................................................... 3
Front and Rear Panel ......................................................................................................................... 4
Before You Begin .....................................................................................................................5
Precautions ........................................................................................................................................ 6
Signing Up for Service ....................................................................................................................... 6
Installation ................................................................................................................................ 7
Installation With A Single Computer .................................................................................................. 8
Installation With A Home Network ................................................................................................... 10
Connecting a Computer to Display the Configuration Pages ........................................................... 12
Basic Configuration .......................................................................................................................... 13
Advanced Configuration ................................................................................................................... 16
Status ............................................................................................................................................... 18
Help .................................................................................................................................................. 20
Troubleshooting ..................................................................................................................... 21
Contact Information ............................................................................................................... 21
Glossary .................................................................................................................................. 22
Software License and Warranty ............................................................................................ 24
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page vii Monday, November 3, 2003 4:19 PM
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page 1 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
Introduction
A Motorola® VT1000v series voice terminal adds Voice over Internet Protocol (VoIP)
connections for one or two telephones to any broadband Internet connection. The
connection can be through either:
■
A cable modem high-speed data service from a cable television company
■
A digital subscriber line (DSL) service from a telephone company
■
Other high-speed Internet connection
The VT1000v product line includes the following models, which collectively are referred
to as a “Motorola voice terminal” in this guide.
VT1003v
Provides one telephone line
VT1005v
Provides two telephone lines
You can use a Motorola voice terminal with any:
Downloaded from www.Manualslib.com manuals search engine
■
Cable modem or DSL modem (broadband modem)
■
Microsoft Windows®, Macintosh®, or UNIX® computer with a 10Base-T or
10/100Base-T Ethernet adapter
■
Ethernet router
1
VT1000User.book Page 2 Monday, November 3, 2003 4:19 PM
Sample Configuration Without A Home Network
You can connect a Motorola voice terminal to any cable modem or DSL modem:
Internet
For simplicity, not all cables are shown.
Broadband
modem
Motorola voice
terminal
Ethernet cables
2
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page 3 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
Sample Configuration With A Home Network
You can connect a Motorola voice terminal to any Ethernet router on a network having a
high-speed Internet connection:
Internet
Broadband
modem
Router
You may need to connect a computer to the
Motorola voice terminal rear panel to configure
the Motorola voice terminal. See “Connecting a
Computer to Display the Configuration Pages”
on page 12.
Motorola
voice terminal
Only if necessary
Downloaded from www.Manualslib.com manuals search engine
3
VT1000User.book Page 4 Monday, November 3, 2003 4:19 PM
Front and Rear Panel
The POWER light on the front panel lights solid green when the power is on.
The rear panel provides the following connectors:
Your Motorola voice terminal may appear slightly
different than in the illustrations in this guide. Some
models do not have every connector illustrated.
Item
Type
Connects To
LINE 2
RJ-11
Telephone line two (on the VT1005v only)
LINE 1
RJ-11
Telephone line one
POWER 12 V
An adapter that you plug into an AC power outlet
WAN
RJ-45
Ethernet connector to your broadband modem, router, switch, or hub.
(“WAN” means “wide area network”)
PC
RJ-45
Ethernet connector to a computer
The WAN and PC connectors each have two adjacent lights:
4
Downloaded from www.Manualslib.com manuals search engine
■
The green light is on when the Ethernet connection is available. It blinks during data
transfer over the port.
■
The yellow light is on if there is a 100Base-T link and off for a 10Base-T link.
VT1000User.book Page 5 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
Before You Begin
Before you begin the installation, check that you received the following items with your
Motorola voice terminal:
Item
Description
AC power adapter
and line cord
Connects the Motorola voice terminal to an AC
electrical outlet
Ethernet cable
Connects the Ethernet port on the Motorola voice
terminal to a computer, if necessary
You also need:
■
DSL, cable modem, broadband gateway, or other high-speed Internet connection
■
One or two touch-tone telephones
You may need an additional 10/100Base-T category 3 or better straight-through Ethernet
cable with RJ-45 terminators.
Downloaded from www.Manualslib.com manuals search engine
5
VT1000User.book Page 6 Monday, November 3, 2003 4:19 PM
Precautions
Caution!
Contact your VoIP provider before connecting your Motorola voice terminal
to your existing telephone wiring. Connect each LINE port to a telephone
only; never to a traditional telephone service.
Postpone installation until there is no risk of thunderstorm or lightning activity in the area.
To prevent overheating the Motorola voice terminal, do not block the ventilation holes on
its sides.
Do not open the Motorola voice terminal. Refer all service to your VoIP provider.
Wipe the Motorola voice terminal with a clean, dry cloth. Never use cleaning fluid or similar
chemicals. Do not spray cleaners directly on the unit or use forced air to remove dust.
Signing Up for Service
To activate voice service, you need to provide the MAC address printed on the bar code label
marked MTA MAC ID on the bottom of the Motorola voice terminal to your VoIP provider.
If you have a DSL modem, you need to obtain the Service Name, User Name, and
Password from your DSL provider.
6
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page 7 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
Installation
Depending on whether you have a single computer or a home network with multiple
computers and a broadband access router, perform one of the following:
■
Installation With A Single Computer
■
Installation With A Home Network
Caution!
To phone
To AC power
Contact your VoIP provider before connecting your Motorola voice terminal to
existing phone wiring. Connect each LINE port to a telephone only; never to a
traditional telephone service.
Be sure the LINE connectors are neither connected together nor connected to
wall jacks on the same network.
To computer
To modem, gateway,
or router
Downloaded from www.Manualslib.com manuals search engine
7
VT1000User.book Page 8 Monday, November 3, 2003 4:19 PM
Installation With A Single Computer
Broadband
Modem
1
Be sure the Motorola voice terminal is unplugged. Be sure power is off to your
broadband modem (cable or DSL) and computer.
2
Connect one end of an Ethernet cable (RJ-45) to the Ethernet connector on your
broadband modem. Connect the other end of this Ethernet cable to the WAN
connector on the Motorola voice terminal.
3
Connect one end of another Ethernet cable to the PC connector on the Motorola
voice terminal. Connect the other end of this Ethernet cable to the Ethernet
connector on the computer.
4
Connect a telephone to the LINE 1 connector using a phone wire (RJ-11). For a
VT1005v only, you can connect a second telephone to the LINE 2 connector.
5
Power on the broadband modem, following the instructions provided with your
modem. Wait about two minutes for it to boot.
6
Plug the AC power adapter to the POWER connector on your Motorola voice
terminal and the electrical outlet. This turns your Motorola voice terminal on. You do
not need to unplug it when not in use.
7
Check that the POWER light on your Motorola voice terminal turns on solid green.
Wait about two minutes for the Motorola voice terminal to boot.
Ethernet port
WAN
Motorola voice
terminal
LINE 1
PC
Ethernet port
Phone
8
Computer
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page 9 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
8
Power up your computer. If your broadband Internet service does not work as it did
before you installed your Motorola voice terminal, please refer to “Troubleshooting”
on page 21.
If you have a cable modem, skip to step 10.
9
If you have a DSL modem, enable PPPoE on your Motorola voice terminal as
described in “Basic Configuration” on page 13.
10 Pick up your telephone hand set and listen for a dial tone. If you hear a dial tone,
you can now call anyone as you would with any telephone.
If you have any problems, please refer to “Troubleshooting” on page 21 or call your
VoIP provider.
Downloaded from www.Manualslib.com manuals search engine
9
VT1000User.book Page 10 Monday, November 3, 2003 4:19 PM
Installation With A Home Network
Broadband
Modem
1
Be sure your Motorola voice terminal is unplugged. Be sure power is off to your
broadband modem (cable or DSL) and router.
2
Connect one end of an Ethernet cable (RJ-45) to an open Ethernet LAN port on
your router. Follow the instructions provided with your router. Connect the other end
of this Ethernet cable to the WAN connector on your Motorola voice terminal.
3
Connect a telephone to your LINE 1 connector using a phone wire (RJ-11). For a
VT1005v only, you can connect a second telephone to the LINE 2 connector.
4
Power on your broadband modem, following the instructions provided with the
modem. Wait about two minutes for it to boot.
5
Power on your router, following the instructions provided with the router. Wait about
two minutes for it to boot.
6
Plug the AC power adapter to the POWER connector on your Motorola voice
terminal and the electrical outlet. This turns your Motorola voice terminal on. You do
not need to unplug it when not in use.
7
Check that the POWER light on your Motorola voice terminal turns on solid green.
Wait about two minutes for the Motorola voice terminal to boot.
Router
LAN ports
WAN
Motorola
voice
terminal
Computer
LINE 1
Computer
PC
Ethernet port
Phone
Computer
(only if
necessary)
See “Connecting a Computer to
Display the Configuration Pages”
10
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page 11 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
8
Downloaded from www.Manualslib.com manuals search engine
Pick up the telephone hand set and listen for a dial tone
■
If you hear a dial tone, you can now call anyone as you normally would on any
telephone.
■
If you do not hear a dial tone, check that all connections described in this
procedure are correct. If you still do not hear a dial tone, you may need to
connect a computer to your Motorola voice terminal and perform Basic
Configuration. If after performing Basic Configuration, you still do not hear a dial
tone, see “Troubleshooting” on page 21 or call your VoIP provider.
11
VT1000User.book Page 12 Monday, November 3, 2003 4:19 PM
Connecting a Computer to Display the
Configuration Pages
For an Installation With A Home Network only, you need to connect a computer with
DHCP enabled to the Motorola voice terminal to display the configuration pages. For
information about enabling DHCP, refer to your operating system documentation.
If you performed an Installation With A Single Computer, a computer is already
connected to the Motorola voice terminal.
To connect a computer to the back of the Motorola voice terminal:
12
Downloaded from www.Manualslib.com manuals search engine
1
Connect one end of an Ethernet cable to the PC connector on the Motorola voice
terminal.
2
Connect the other end of the Ethernet cable to the Ethernet connector on a
computer.
3
Power up the computer.
VT1000User.book Page 13 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
Basic Configuration
To perform basic configuration:
1 On the computer connected to the voice terminal PC port, start a web browser such
as Microsoft® Internet Explorer or Netscape Navigator®.
2
3
In the Address or Location field, type http://192.168.102.1 and press ENTER to
display the Status page, which displays the Motorola voice terminal settings.
Click Basic Configuration to display the Basic Configuration window. Its fields are:
Obtain IP
Address
Dynamically
This setting is enabled by default. If either of the following is true, no
configuration on this page is required:
■ If you have a cable modem with no router and your cable provider
assigns IP addresses dynamically, the Motorola voice terminal
obtains its IP address dynamically from your cable provider.
■ If you have a router with DHCP enabled, the Motorola voice
terminal obtains its IP address dynamically from your router.
Specify Static
IP Address
If your broadband provider requires a static IP address, enable
Specify Static IP Address. Type the Static IP Address and IP
addresses for the Subnet Mask, Default Gateway they provide.
Enable PPPoE If you have a DSL modem and no router, enable PPPoE and type the
Service Name, User Name, and Password provided by your
DSL provider.
Downloaded from www.Manualslib.com manuals search engine
13
VT1000User.book Page 14 Monday, November 3, 2003 4:19 PM
Specify DNS
Servers
14
Downloaded from www.Manualslib.com manuals search engine
Enables you to specify Domain Name System (DNS) servers, if
necessary:
■ If Obtain IP Address Dynamically or Enable PPPoE are checked,
Specify DNS Servers is unchecked by default. If required by your
broadband provider only, check this box and type the DNS server
IP addresses provided by your broadband provider.
■ If Specify Static IP Address is checked, Specify DNS Servers is
checked by default. Because no DNS server is automatically
assigned, you need to type the DNS server IP addresses
provided by your broadband provider.
4
Verify that all fields are correctly filled in and click Save Changes. The message
This will require a reboot of the unit. Are you sure?
is displayed.
5
Click OK. Wait about two minutes. You cannot display the configuration pages while
the Motorola voice terminal reboots. After the Motorola voice terminal reboots, click
the web browser Refresh button to display the configuration pages.
6
Pick up the telephone hand set and listen for a dial tone. If you hear a dial tone, you
can now place a phone call as you would with any telephone.
VT1000User.book Page 15 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
If you cannot a hear a dial tone, try the following:
Downloaded from www.Manualslib.com manuals search engine
■
Check that all cabling is correctly connected as described in “Installation With A
Single Computer” on page 8 or “Installation With A Home Network” on page 10.
■
Repeat this Basic Configuration procedure. Be sure you enter the correct
information for your service.
■
Refer to “Troubleshooting” on page 21.
■
Contact your VoIP provider.
15
VT1000User.book Page 16 Monday, November 3, 2003 4:19 PM
Advanced Configuration
Do not change these settings unless you have the necessary expertise and the need to
do so.
Field or Button
Description
Enable DHCP/NAT
on LAN Port
If this is enabled, the Motorola voice terminal automatically distributes
an IP address to a computer connected to its PC port. It is enabled by
default.
Virtual Servers
Configures logical data ports for applications requiring multiple data
ports. Because NAT assumes that data sent through one port will
return to the same port, you may need to configure virtual servers to
run certain applications:
■
IP is the IP address of the computer connected to the Motorola
voice terminal
Port sets the port to open. The ports assigned to Motorola voice
terminal voice functions are displayed. If you forward any of
these ports, you may disrupt your voice service. The ports shown
in the illustration are examples only.
■
Transport sets the protocol — Disabled, TCP, IP, or UDP.
■
16
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page 17 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
Downloaded from www.Manualslib.com manuals search engine
Field or Button
Description
Host Name
Sets the host name, if required by your broadband service provider.
MAC Address
Override
If your broadband provider associates a particular service to a specific
device, such as your computer, type its MAC address here to use
instead of the Motorola voice terminal MAC address.
By default, the MAC address printed on the Motorola voice terminal is
displayed in this field.
Restore MAC
Address
If you type a value in the MAC Address Override field, click to use the
actual Motorola voice terminal MAC address instead.
Save Changes
After verifying that all fields are correctly filled in, click to save your
changes. The message This will require a reboot of
the unit. Are you sure? is displayed. Click OK.
Reboot
Click to restart the Motorola voice terminal. Rebooting takes about
two minutes.
17
VT1000User.book Page 18 Monday, November 3, 2003 4:19 PM
Status
The Status window displays the Motorola voice terminal configuration.
Field
Description
WAN IP Address
Assignment
Displays the method chosen on the Basic Configuration page —
Dynamic, Static, or PPPoE.
IP Address
Subnet Mask
Default Gateway
18
Downloaded from www.Manualslib.com manuals search engine
These fields display the Motorola voice terminal IP address, subnet
mask, and default gateway IP address:
■ For a cable modem with no router where the cable provider
assigns IP addresses dynamically, these are obtained
dynamically from the cable provider.
■ For static assignment, these are defined on the Basic
Configuration page.
DNS Servers
Displays the DNS servers assigned to your computer.
DHCP Server/NAT
Displays whether Enable DHCP/NAT on LAN Port is enabled on the
Advanced Configuration page.
VT1000User.book Page 19 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
Field
Description
WAN MAC Address Displays the Motorola voice terminal MAC address. By default, it
displays the MAC address written to read-only memory (ROM) at the
factory and printed in the MTA MAC ID field on the bottom of the unit.
If you use the MAC Address Override field on the Advanced
Configuration page, the MAC address you typed there is displayed in
this field.
User Phone
Number
Downloaded from www.Manualslib.com manuals search engine
Displays the telephone number(s) assigned by your VoIP provider.
19
VT1000User.book Page 20 Monday, November 3, 2003 4:19 PM
Help
The Help window displays:
20
Downloaded from www.Manualslib.com manuals search engine
■
Software, hardware, and VoIP provider configuration file versions
■
Brief descriptions of the Motorola voice terminal configuration pages
VT1000User.book Page 21 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
License
Troubleshooting
If the solutions listed here do not solve your problem, check your broadband modem user guide or contact your VoIP provider.
Problem
Possible Solutions
Green POWER light is off
Check that the AC power adapter is properly plugged into the electrical outlet and the Motorola voice terminal.
Check that the electrical outlet is working.
Cannot send or receive data Check whether the telephone line cord is connected to the Motorola voice terminal.
or calls; no dial tone
Check all other cabling between the modem, Motorola voice terminal, computer, and if applicable, routers. Be sure you
used the cables provided with the Motorola voice terminal. All Ethernet cables must be straight-through cables.
Check the lights on the modem front panel. For example, on the Motorola SURFBoard cable modem, the first light from
top to bottom that is off indicates the error. For information, see your broadband modem user guide.
To establish network connectivity, it is often helpful to follow the correct sequence. Be sure you complete the installation
steps in the order specified in “Installation With A Single Computer” on page 8 or “Installation With A Home Network” on
page 10.
Contact Information
For technical support, contact your VoIP provider.
For information about Motorola consumer broadband products, education, and support, visit http://broadband.motorola.com.
Downloaded from www.Manualslib.com manuals search engine
21
VT1000User.book Page 22 Monday, November 3, 2003 4:19 PM
License
Glossary
broadband
High-speed telecommunication over a wide range of frequencies, typically 256 Kbps or faster. Broadband enables more information to
be transmitted in less time. The most common broadband service types available to home and small-office users are cable modem or
DSL. Both cable modem and DSL are much faster than a traditional dial-up Internet connection.
broadband service If you have a cable modem, the cable company from which you subscribe to high-speed data service.
provider
If you have a DSL modem, the company from which you subscribe to DSL service.
cable modem
A device enabling a broadband connection to the Internet over cable television lines. It requires a subscription for high-speed data
service from your local broadband service provider.
coaxial cable
(coax)
A type of wire consisting of a center wire surrounded by insulation and a grounded shield of braided wire traditionally used mainly to
carry cable television signals. The shield minimizes electrical and radio frequency interference.
digital subscriber A device enabling a broadband connection to the Internet over traditional telephone lines that support DSL. It requires a subscription
line (DSL) modem for DSL service from your local telephone company.
Domain Name
System (DNS)
download
The DNS is the Internet system for converting domain names to IP addresses. A DNS server contains a table matching domain names
such as Internetname.com to IP addresses such as 192.169.9.1. When you access the world-wide web, a DNS server translates the
URL displayed on the browser to the destination website IP address. The DNS lookup table is a distributed Internet database; no one
DNS server lists all domain name to IP address matches.
To copy a file from one computer to another. You can use the Internet to download files from a server to your home computer.
downstream
In a cable data or DSL network, downstream describes the direction of data received by your computer from the Internet.
Dynamic Host
Configuration
Protocol (DHCP)
A DHCP server dynamically assigns IP addresses to client hosts on an IP network. DHCP eliminates the need to manually assign
static IP addresses by “leasing” an IP address and subnet mask to each client. It enables the automatic reuse of unused IP addresses.
22
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page 23 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
License
Ethernet
The most widely used type of local area network (LAN). The most commonly installed Ethernet networks are called 10Base-T.
10Base-T provides transmission speeds up to 10 megabits per second (Mbps), usually over twisted-pair wire. Fast Ethernet
(100Base-T) provides transmission speeds up to 100 Mbps.
IP address
An Internet Protocol address is an identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol route
messages based on the destination IP address. Your broadband service provider assigns your cable modem an IP address to provide
a continuous Internet connection.
MAC address
The Media Access Control address uniquely identifies each device that can be connected to an Ethernet network. It is permanently
written to read-only memory (ROM) at the factory and printed on your Motorola voice terminal.
MHz
Mega Hertz. A measure of radio frequency - millions of cycles per second. One MHz means one million cycles per second.
Network Address
Translation (NAT)
NAT is an Internet standard for a LAN to use one set of IP addresses for internal traffic and a second set of IP addresses for external
traffic.
port
PPPoE
On a computer or other electronic device, a port is a socket or plug used to physically connect it to the network or to other devices.
In TCP/IP, a port is a number from 0 to 65536 used logically by a client program to specify a server program. Ports 0 to 1024 are reserved.
Point-to-Point Protocol over Ethernet specification for connecting to the Internet with DSL modems.
RJ-11
The most common type of connector for household or office phones.
RJ-45
The most common type of connector for Ethernet networks.
TCP/IP
Transmission Control Protocol/Internet Protocol is a set of protocols that provides rules for communication between networks.
upstream
In a cable data or DSL network, upstream describes the direction of data sent from your computer to the Internet.
VoIP
Voice over Internet Protocol is a method to exchange voice, fax, and other information over the Internet. Voice and fax have
traditionally been carried over telephone lines using a dedicated circuit for each line. VoIP enables calls to travel as discrete data
packets on shared lines.
VoIP provider
The company from which you purchase VoIP telephone service. It may be different from your broadband service provider.
Downloaded from www.Manualslib.com manuals search engine
23
VT1000User.book Page 24 Monday, November 3, 2003 4:19 PM
License
Software License and Warranty
Motorola, Inc., Broadband Communications Sector (“Motorola”)
Cable Data Division
101 Tournament Drive
Horsham, PA 19044
License
IMPORTANT: PLEASE READ THIS SOFTWARE LICENSE (“LICENSE”) CAREFULLY BEFORE YOU INSTALL, DOWNLOAD OR USE ANY APPLICATION SOFTWARE, USB DRIVER
SOFTWARE, FIRMWARE AND RELATED DOCUMENTATION (“SOFTWARE”) PROVIDED WITH MOTOROLA’S CABLE DATA PRODUCT (THE “CABLE DATA PRODUCT”). BY USING
THE CABLE DATA PRODUCT AND/OR INSTALLING, DOWNLOADING OR USING ANY OF THE SOFTWARE, YOU INDICATE YOUR ACCEPTANCE OF EACH OF THE TERMS OF
THIS LICENSE. UPON ACCEPTANCE, THIS LICENSE WILL BE A LEGALLY BINDING AGREEMENT BETWEEN YOU AND MOTOROLA. THE TERMS OF THIS LICENSE APPLY TO
YOU AND TO ANY SUBSEQUENT USER OF THIS SOFTWARE.
IF YOU DO NOT AGREE TO ALL OF THE TERMS OF THIS LICENSE (I) DO NOT INSTALL OR USE THE SOFTWARE AND (II) RETURN THE CABLE DATA PRODUCT AND THE
SOFTWARE (COLLECTIVELY, “PRODUCT”), INCLUDING ALL COMPONENTS, DOCUMENTATION AND ANY OTHER MATERIALS PROVIDED WITH THE PRODUCT, TO YOUR
POINT OF PURCHASE OR SERVICE PROVIDER, AS THE CASE MAY BE, FOR A FULL REFUND. BY INSTALLING OR USING THE SOFTWARE, YOU AGREE TO BE BOUND BY THE
PROVISIONS OF THIS LICENSE AGREEMENT.
The Software includes associated media, any printed materials, and any “on-line” or electronic documentation. Software provided by 3rd parties may be subject to separate end-user
license agreements from the manufacturers of such Software.
The Software is never sold. Motorola licenses the Software to the original customer and to any subsequent licensee for personal use only on the terms of this License. Motorola and its 3rd
party licensors retain the ownership of the Software.
You may:
USE the Software only in connection with the operation of the Product.
TRANSFER the Software (including all component parts and printed materials) permanently to another person, but only if the person agrees to accept all of the terms of this License. If you
transfer the Software, you must at the same time transfer the Product and all copies of the Software (if applicable) to the same person or destroy any copies not transferred.
TERMINATE this License by destroying the original and all copies of the Software (if applicable) in whatever form.
You may not:
(1) Loan, distribute, rent, lease, give, sublicense or otherwise transfer the Software, in whole or in part, to any other person, except as permitted under the TRANSFER paragraph above.
(2) Copy or translate the User Guide included with the Software, other than for personal use. (3) Copy, alter, translate, decompile, disassemble or reverse engineer the Software, including
but not limited to, modifying the Software to make it operate on non-compatible hardware. (4) Remove, alter or cause not to be displayed, any copyright notices or startup message
contained in the Software programs or documentation. (5) Export the Software or the Product components in violation of any United States export laws.
The Product is not designed or intended for use in on-line control of aircraft, air traffic, aircraft navigation or aircraft communications; or in design, construction, operation or maintenance of any
nuclear facility. MOTOROLA AND ITS 3rd PARTY LICENSORS DISCLAIM ANY EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR SUCH USES. YOU REPRESENT AND
WARRANT THAT YOU SHALL NOT USE THE PRODUCT FOR SUCH PURPOSES.
24
Downloaded from www.Manualslib.com manuals search engine
VT1000User.book Page 25 Monday, November 3, 2003 4:19 PM
VT1000v Series Voice Terminal User Guide
License
Title to this Software, including the ownership of all copyrights, mask work rights, patents, trademarks and all other intellectual property rights subsisting in the foregoing, and all adaptations
to and modifications of the foregoing shall at all times remain with Motorola and its 3rd party licensors. Motorola retains all rights not expressly licensed under this License. The Software,
including any images, graphics, photographs, animation, video, audio, music and text incorporated therein is owned by Motorola or its 3rd party licensors and is protected by United States
copyright laws and international treaty provisions. Except as otherwise expressly provided in this License, the copying, reproduction, distribution or preparation of derivative works of the
Software, any portion of the Product or the documentation is strictly prohibited by such laws and treaty provisions. Nothing in this License constitutes a waiver of Motorola’s rights under
United States copyright law.
This License and your rights regarding any matter it addresses are governed by the laws of the Commonwealth of Pennsylvania, without reference to conflict of laws principles. THIS
LICENSE SHALL TERMINATE AUTOMATICALLY if you fail to comply with the terms of this License.
Motorola is not responsible for any 3rd party software provided as a bundled application, or otherwise, with the Software.
U.S. GOVERNMENT RESTRICTED RIGHTS
The Product and documentation is provided with RESTRICTED RIGHTS. The use, duplication or disclosure by the Government is subject to restrictions as set forth in subdivision (c)(1)(ii)
of The Rights in Technical Data and Computer Software clause at 52.227-7013. The contractor/manufacturer is Motorola, Inc., Broadband Communications Sector, 101 Tournament Drive,
Horsham, PA 19044.
Warranty Information
MOTOROLA DOES NOT EXTEND ANY WARRANTY DIRECTLY TO YOU, THE END USER, WITH RESPECT TO THIS PRODUCT. A LIMITED WARRANTY FOR THIS PRODUCT MAY
HAVE BEEN PROVIDED TO YOU BY YOUR SERVICE PROVIDER (“SERVICE PROVIDER”) FROM WHOM YOU OBTAINED THE PRODUCT. PLEASE CONTACT YOUR SERVICE
PROVIDER IF YOU EXPERIENCE PROBLEMS. MOTOROLA HEREBY EXPRESSLY DISCLAIMS THE APPLICATION OF ANY EXPRESS, IMPLIED OR STATUTORY WARRANTIES,
INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND/OR THE WARRANTY AGAINST
INFRINGEMENT PROVIDED IN THE UNIFORM COMMERCIAL CODE. MOTOROLA ALSO IS NOT RESPONSIBLE FOR, AND PROVIDES “AS IS” ANY SOFTWARE SUPPLIED BY 3rd
PARTIES.
IN NO EVENT SHALL MOTOROLA BE LIABLE TO YOU OR ANY OTHER PARTY FOR ANY DIRECT, INDIRECT, GENERAL, SPECIAL, INCIDENTAL, CONSEQUENTIAL, EXEMPLARY
OR OTHER DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, LOSS OF INFORMATION OR ANY OTHER PECUNIARY LOSS), OR FROM ANY BREACH OF WARRANTY, EVEN IF MOTOROLA HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES. MOTOROLA IS NOT RESPONSIBLE FOR PROBLEMS OR DAMAGE CAUSED BY THE INTERACTION OF THE PRODUCT WITH ANY
OTHER SOFTWARE OR HARDWARE.
THE REMEDIES DESCRIBED IN THIS DOCUMENT ARE YOUR SOLE AND EXCLUSIVE REMEDIES FOR ANY AND ALL CLAIMS THAT YOU MAY HAVE ARISING OUT OF OR IN
CONNECTION WITH THIS PRODUCT, WHETHER MADE OR SUFFERED BY YOU OR ANOTHER PERSON AND WHETHER BASED IN CONTRACT OR TORT.
These matters are governed by the laws of the Commonwealth of Pennsylvania, without regard to conflict of laws principles and excluding the provisions of the United Nations Convention
on Contracts for the International Sale of Goods.
Downloaded from www.Manualslib.com manuals search engine
25
VT1000User.book Page 26 Monday, November 3, 2003 4:19 PM
Visit our website at:
www.motorola.com
509766-001
11/03
MGBI
Downloaded from www.Manualslib.com manuals search engine
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement