Ultra chef UC475SB Instruction manual

Ultra chef UC475SB Instruction manual
This gas grill must be used only outdoors in a well-ventilated space and must not be used inside a
building, garage, screened-in porch, gazebo or any other enclosed area.
APPLY SERIAL NUMBER LABEL FROM CARTON
Serial No.
XXXXXX000000
MODEL NO.
ULTRA CHEF 485
L485, L485RB, L485SB,
L485SIB, L485RSB, L485RSIB
WARNING
DANGER
IF YOU SMELL GAS:
• Shut off gas to the appliance.
• Extinguish any open flame.
• Open lid.
• If odor continues, keep away from the
appliance and immediately call your gas
supplier or fire department.
Do not try to light this appliance without
reading the “LIGHTING” instructions section of
this manual.
Do not store or use gasoline or other flammable
liquids or vapors in the vicinity of this or any
other appliance. An L.P. cylinder not connected
for use must not be stored in the vicinity of
this or any other appliance. If the information
in these instructions is not followed exactly, a
fire or explosion may result, causing property
damage, personal injury or death.
Notice to Installer: Leave these instructions with the grill owner for future reference.
3194571
NAC
214 Bayview Dr., Barrie, Ontario, Canada L4N 4Y8 Phone: (705)726-4278
Fax: (705)725-2564 email: [email protected] web site: www.ultrachefgrills.com
N415-0220UC SEPT 17/10
2
ULTRA CHEF® products are designed with superior components and materials, and are
assembled by trained craftsmen who take great pride in their work. The burner and valve
assembly are leak tested and test-fired at a quality test station, and thoroughly inspected
by a qualified technician before packaging and shipping to ensure that you, the customer,
receive the quality product you expect from Napoleon Appliance Corporation.
ULTRA CHEF® GAS GRILL LIMITED WARRANTY
NAPOLEON APPLIANCE CORPORATION warrants the following materials and workmanship
in your new ULTRA CHEF® gas grill against defects for 10years. This covers aluminum castings
(excluding paint), side shelves (excluding paint), stainless steel control panel (excluding
screen printing), stainless steel burners, stainless steel or porcelain lid and base inserts, and
lid handles, subject to the following conditions: During the first five years NAPOLEON APPLIANCE
CORPORATION will provide replacement parts at our option free of charge. From the sixth
year to the tenth year, NAPOLEON APPLIANCE CORPORATION will provide replacement
parts at 50% of the current retail price.
Components such as stainless steel or porcelain sear plates, stainless steel or cast iron
cooking grids, valves with ignition system, temperature gauges, knobs, and ceramic infrared
burners (excluding screens) are covered and NAPOLEON APPLIANCE CORPORATION will
provide parts free of charge during the first two years of the limited warranty.
All other components including regulators, casters, warming racks, hoses and connectors,
I-GLOW™, fasteners and accessories are covered and NAPOLEON APPLIANCE CORPORATION
will provide parts free of charge during the first year of the limited warranty.
NAPOLEON APPLIANCE CORPORATION shall not be liable for any transportation charges,
labor costs or export duties.
Conditions And Limitations
“Napoleon Appliance Corporation” warrants its products against manufacturing defects to the original purchaser only, provided that the purchase was made
through an authorized ULTRA CHEF® dealer and is subject to the following conditions and limitations:”
This factory warranty is non-transferable and may not be extended what so ever by any of our representatives.
The gas grill must be installed by a licenced, authorized service technician or contractor. Installation must be done in accordance with the installation
instructions included with the product and all local and national building and fire codes.
This limited warranty does not cover damages caused by misuse, lack of maintenance, grease fires, hostile environments, accident, alterations, abuse or
neglect and parts installed from other manufacturers will nullify this warranty.
This limited warranty further does not cover any scratches, dents, painted finishes, corrosion or discolouring by heat, abrasive and chemical cleaners, nor
chipping on porcelain enamel parts, nor any components used in the installation of the gas grill.
Should deterioration of parts occur to the degree of non-performance within the duration of the warranted coverage, a replacement part will be provided.
In the first year only, this warranty extends to the replacement of warranted parts, which are defective in material or workmanship provided that the product
has been operated in accordance with the operation instructions and under normal conditions.
After the first year, with respect to this President’s Limited Lifetime Warranty, Napoleon Appliance Corporation may, at its discretion, fully discharge all obligations
with respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but defective part(s).
Napoleon Appliance Corporation will not be responsible for the installation, labour or any other costs or expenses related to the re-installation of a warranted
part, and such expenses are not covered by this warranty.
Notwithstanding any provision contained in this President’s Limited Lifetime Warranty Napoleon Appliance Corporation ‘s responsibility under this warranty
is defined as above and it shall not in any event extend to any incidental, consequential, or indirect damages.
This warranty defines the obligation and liability of Napoleon Appliance Corporation with respect to the ULTRA CHEF® gas grill and any other warranties
expressed or implied with respect to this product, its components or accessories are excluded.
Napoleon Appliance Corporation neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this
product. Napoleon Appliance Corporation will not be responsible for: over firing, blow outs caused by environmental conditions such as strong winds, or
inadequate ventilation.
Any damages to the gas grill due to weather damage, hail, rough handling, damaging chemicals or cleaners will not be the responsibility of Napoleon Appliance
Corporation.
The bill of sale or a copy will be required together with a serial number and a model number when making any warranty claims from Napoleon Appliance
Corporation.
Napoleon Appliance Corporation reserves the right to have its representative inspect any product or part prior to honouring any warranty claim.
Napoleon Appliance Corporation shall not be liable for any transportation charges, labour costs, or export duties.
www.ultrachefgrills.com
3
WARNING! Failure to follow these instructions could result in property damage, personal injury or
death. Read and follow all warnings and instructions in this manual prior to operating grill.
Safe Operating Practices
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
This gas grill must be assembled exactly according to the instructions in the manual. If the grill was store
assembled, you must review the assembly instructions to confirm correct assembly and perform the
required leak tests before operating the grill.
Read the entire instruction manual before operating the gas grill.
Under no circumstance should this gas grill be modified.
Follow lighting instructions carefully when operating grill.
Gas must be turned off at the propane cylinder or at the natural gas supply valve when the gas grill is not
in use.
Keep children and pets away from hot grill, DO NOT allow children to climb inside cabinet.
Do not leave the grill unattended while in use.
Do not move grill when hot or operating.
This gas grill must not be installed in or on recreational vehicles and/or boats.
This gas grill must only be stored outdoors in a well-ventilated area and must not be used inside a building,
garage, screened -in porch or any other enclosed area.
Maintain proper clearance to combustibles (16” to rear of unit 7” to sides). Additional clearance (24”) is
recommended near vinyl siding or panes of glass.
At all times keep the ventilation openings of the cylinder enclosure free and clear from debris.
Do not operate unit under any combustible construction.
Do not locate in windy settings. High winds adversely affect the cooking performance of the gas grill.
When the gas grill is stored indoors, the propane cylinder must be disconnected from the grill and stored
outdoors in a well-ventilated area, disconnected cylinders must not be stored in a building, garage or other
enclosed area. Natural gas units must be disconnected from the supply when being stored indoors.
Inspect the gas line hose before each use. If there is evidence of excessive abrasion or wear, it must be
replaced before using the gas grill, with a replacement hose assembly specified by the grill manufacturer.
Never store a spare LP gas cylinder under or near this grill.
Never fill the cylinder beyond 80 % full.
Do not attempt to use a cylinder, which is not equipped with a QCC1 type connection.
Leak test all connections before initial use, even if the grill was purchased fully assembled, annually or
whenever any gas component has been replaced.
Never use natural gas in a unit designed for liquid propane gas.
Never use lighter fluid in a gas grill.
Use charcoal briquettes only with a Napoleon charcoal tray designed for this unit.
Burner controls must be off when turning supply cylinder on.
Do not light burners with lid closed.
Do not operate rear burner with main burners operating.
The lid is to be closed during the preheat period.
Do not route hose underneath drip pan-proper hose clearance to bottom of unit must be maintained.
Clean grease tray and sear plates regularly to avoid build-up, which may lead to grease fires.
Remove warming rack before lighting rear burner. The extreme heat will damage the warming rack.
Ensure sear plates are positioned properly according to sear plate installation instructions. Do not use side shelves to store lighters, matches or any other combustibles.
Keep gas line away from heated surfaces
Keep any electrical supply cord away from water or heated surfaces.
Inspect infrared burner venturi tube for spider webs and other obstructions periodically. Clean the tubes
completely if you find any such obstructions.
The outdoor cooking gas grill and its individual shutoff valve must be disconnected from the gas supply
piping system during any pressure testing of that system at test pressures in excess of 0.5psi (3.5kPa).
The outdoor cooking gas grill must be isolated from the gas supply piping system by closing its individual
manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to
or less than 1/2 psi (3.5 kPa).
www.ultrachefgrills.com
4
Electrical Precautions
WARNING! Failure to follow these instructions could result in property damage, personal injury or
death.
•
To protect against electric shock, do not immerse cord or plugs in water or other liquid.
•
Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking
off parts.
•
Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance
malfunctions or has been damaged in any manner. Contact the manufacturer for repair.
•
Do not let the cord hang over the edge of a table or touch hot surfaces.
•
Do not use an outdoor cooking gas appliance for purposes other than intended.
•
When connecting, first connect plug to the outdoor cooking gas appliance then plug appliance into the
outlet.
•
Use only a Ground Fault Interrupter (GFI) protected circuit with this outdoor cooking gas appliance.
•
Never remove the grounding plug or use with an adapter of 2 prongs.
•
Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and approved
for outdoor use with a W-A marking.
Cylinder Specification/Gas Hook Up
This gas barbecue is certified under Canadian and American National Standards, CSA 1.6-2008 and ANSI
Z21.58a -2008 respectively for outdoor gas grills and should be installed to conform with local codes. In
absence of local codes, install to the current CAN/CSA-B149.1 Propane Installation Code in Canada or to the
National Fuel Gas Code, ANSI Z223.1 in the United States.
When installed, the unit must be electrically grounded in accordance with local codes or, in absence of local
codes, with the current CSA C22.1 Canadian electrical code in Canada or the National Electrical Code,
ANSI/NFPA 70 in the United States.
If a rotisserie motor is used, it must be electrically grounded in accordance with local codes or, in absence of
local codes, with the current CSA C22.1 Canadian electrical code in Canada or the National Electrical Code,
ANSI/NFPA 70 in the United States.
California Proposition 65: The burning of gas fuel creates by-products, some of which are on the list as
substances known by the State of California to cause cancer or reproductive harm. When cooking with gas,
always ensure adequate ventilation to the unit, to minimize exposure to such substances.
Propane Cylinder Specifications
WARNING! If these instructions are not followed exactly, a fire causing death or serious injury may
occur.
A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never use a
cylinder with a damaged valve. Use only a propane supply cylinder constructed and marked in accordance
with the specifications for LP-gas cylinders of the National Standard of Canada, CAN/CSA-b339, Cylinders,
Spheres and Tubes for Transportation of Dangerous Goods; and Commission, as applicable or the Specifications
for LP-Gas Cylinders of the U.S. Department of Transportation (D.O.T.). This appliance has been designed for
use with a 20 lb. (9.1 kg) size propane cylinder only (not supplied).
The propane cylinder must be provided with a cylinder connection device compatible with the connection
for outdoor cooking appliances. The propane cylinder must be provided with a shut-off valve terminating in
a propane cylinder valve type QCC1, and a safety relief device having direct communication with the vapor
space of the cylinder. The cylinder supply system must be arranged for vapor withdrawal and the cylinder shall
include a collar to protect the cylinder valve. The cylinder shall incorporate a listed OPD (overfill protection
device). Do not store a spare LP-gas cylinder under or near this appliance. Never fill the cylinder beyond 80
percent full.
www.ultrachefgrills.com
5
Propane Cylinder Installation
Cylinder Connection: Ensure that the gas regulator hose is kink free. Remove the cap or plug from the cylinder
fuel valve. Insert the black QCC1 regulator nipple onto the QCC1 fuel valve. Hand tighten clockwise. Do not use
tools. Leak test all joints prior to using the barbecue. A leak test must be performed annually, and each time a
cylinder is hooked up, or if a part of the gas system is replaced.
•
Check that the cylinder valve is closed by turning the knob clockwise.
•
Check that the grill’s burner knobs are in the off position.
•
Open cabinet doors.
•
Place the cylinder into the tank holder in bottom of shelf.
•
Position the cylinder so that the valve faces toward the front of the unit.
•
Attach regulator hose.
WARNING! Use only the pressure regulator and hose assembly provided with this barbecue. Replacement
pressure regulators and hose assemblies must be specified by the manufacturer. Do not store a spare
propane cylinder on the shelf beneath the barbecue. The regulator must be attached so that no part of the
hose touches the underside of the grill or drippan. A fire will result if these directions are ignored.
The regulator supplies a pressure of 11 inches. water column to the gas grill and has a QCC1 type fitting. Cylinders
to be used with this unit must be supplied with a QCC1 cylinder valve. A QCC1 cylinder has a positive seating
connection, which will not allow gas flow until a positive seal has been achieved. It is also equipped with an
excess flow device. In order to attain full flow to the grill, the valves must be in the off position when the cylinder
valve is turned on.
Natural Gas Hook-Up
This natural gas grill is supplied with a 10ft supply hose (complete with a quick disconnect) designed for natural
gas and certified for outdoor use. The gas grill is designed to operate at an inlet pressure of 7 inches water
column. Piping and valves upstream of the quick disconnect are not supplied. The installation must comply
with CAN B149.1 Natural Gas and Propane installation code in Canada, or to the National Fuel Gas Code,
ANSI Z223.1 in the United States. The gas supply pipe must be sufficiently sized to supply the BTU/h specified
on the rating plate, based on the length of the piping run. The quick disconnect must not be installed in an
upward direction and a readily accessible manual shut-off valve must be installed upstream of, and as close to,
the quick disconnect as is feasible. The flared end of the hose must be connected to the fitting on the end of
the flex tube as illustrated in the Natural Gas Hose Attachment diagram. Tighten using two wrenches. (Do not
use thread sealer/pipe dope.) These connections must be made by a licensed gas installer. Leak test all joints
prior to using the gas grill.
WARNING!
•
The installation must be performed by a licensed gas fitter, and all connections must be leak tested before
operating the grill.
•
Do not route hose underneath drip pan.
•
Do not route hose between space in bottom shelf and back panel.
•
Do not route hose over top of back panel.
•
Ensure all hose connections are tightened using two wrenches. Do not use teflon tape or pipe dope on
any hose connection.
•
Ensure the hose does not contact any high temperature surfaces, or it may melt and leak causing a fire.
•
Do not use enclosure to store excess hose, as there is a greater chance of the hose contacting a hot surface,
it may melt and leak causing a fire.
•
Leak test all the connections using a soap and water solution, as per the leak testing instructions found in
the this manual.
www.ultrachefgrills.com
6
Leak Testing Instructions
WARNING! A leak test must be performed annually and each time a cylinder is hooked up or if a part
of the gas system is replaced.
Warning! Never use an open flame to check for gas leaks. Be certain no sparks or open flames are
in the area while you check for leaks. Sparks or open flames will result in a fire or explosion, damage to
property, serious bodily injury, or death.
Leak testing: This must be done before initial use, annually, and whenever any gas components are replaced
or serviced. Do not smoke while performing this test, and remove all sources of ignition. See Leak Testing
Diagram for areas to check. Turn all burner controls to the off position. Turn gas supply valve on.
Brush a half-and-half solution of liquid soap and water onto all joints and connections of the regulator, hose,
manifolds and valves.
Bubbles will indicate a gas leak. Either tighten the loose joint or have the part replaced with one recommended
by the Napoleon Customer Care department and have the grill inspected by a certified gas installer.
If the leak cannot be stopped, immediately shut off the gas supply, disconnect it, and have the grill inspected
by a certified gas installer or dealer. Do not use the grill until the leak has been corrected.
www.ultrachefgrills.com
7
Lighting Instructions
Side Burner
Lights Left Burner Rear Burner Centre Burner Right Burner
Side Burner Igniter
Off Position
WARNING! Open lid
WARNING! Ensure all burner controls are in the off position. Turn on the gas supply valve.
Main Tube Burner
Lighting
Rear Burner Lighting
(If equipped)
Side Burner Lighting
(If equipped)
1. Open grill lid.
1. Open grill lid.
1. Open/Remove side burner cover.
2. Push and turn any main burner
knob slowly to the ’hi’ position. This
action will ignite the pilot flame which
will in turn light the selected burner. If
the pilot lights, continue to push down
on the control knob until the burner
lights and then release.
2. Remove the warming rack
2. Push and turn side burner control
to high position.
3. If the pilot does not ignite, then
immediately turn the control knob
back to the ‘off position and repeat
step 1 several times.
.
3. Clip a match into the supplied
lighting rod. Hold a lit match to
right end ports of rear burner. Turn
rear burner to high.
3. Press and hold
igniter button until burner lights, or
light by match
4. If the pilot and burner will not
ignite within 5 seconds, turn the
control knob to the ‘off’ position and
wait 5 minutes for any excess gas to
dissipate. Either repeat steps 1 and 2
or light with a match.
4. If the burner will not ignite within
5 seconds, turn the control knob to
the ‘off’ position and wait 5 minutes
for any excess gas to dissipate. Either
repeat steps 2 and 3 or light with a
match.
WARNING! The propane cylinder is equipped with an excess flow device.
Unless all burners
are turned off prior to turning the cylinder on, only small flames and low heat will
be achievable.
WARNING! Do not use the rear burner (rotisserie burner) with the main burners operating.
WARNING! If lighting the unit with a match, clip the match into the supplied lighting rod.
Hold the lit match down through the grill and sear plate while turning the
corresponding burner valve to high.
www.ultrachefgrills.com
8
Operating The Grill
Initial Lighting: When lit for the first time, the gas grill emits a slight odor. This is a normal temporary condition
caused by the “burn-in” of internal paints and lubricants used in the manufacturing process and does not occur
again. Simply run the main burners on high for approximately one-half hour.
Main Burner Use: When searing foods, we recommend preheating the grill by operating all main burners
in the high position with the lid closed for approximately 10 minutes. Food cooked for short periods of time
(fish, vegetables) can be grilled with the lid open. Cooking with the lid closed will ensure higher, more even
temperatures that can reduce cooking time and cook meat more evenly. Food that has a cooking time longer
than 30 minutes, such as roasts, can be cooked indirectly (with the burner lit opposite to the food placement).
When cooking very lean meats, such as chicken breasts or lean pork, the grids can be oiled before pre-heating
to reduce sticking. Cooking meat with a high degree of fat content can create flare-ups. Either trim the fat or
reduce temperatures to inhibit this. Should a flare-up occur, move food away from the flames and reduce the
heat. Leave the lid open. See Your All Season Grill cookbook by Napoleon for more detailed instructions.
Direct Cooking: Place food to be cooked on the grill directly over the heat. This method is generally used for
searing or for foods that do not require prolonged cooking times such as hamburgers, steaks, chicken pieces,
or vegetables. The food is first seared to trap-in the juices and flavor, and then the temperature is lowered to
finish cooking the food to your preference.
Indirect Cooking: With one or more burners operating, place food to be cooked on the grill over a burner that
is not operating. The heat circulates around the food, cooking slowly and evenly. Cooking with this method is
much the same as cooking in your oven and is generally used for larger cuts of meats such as roasts, chickens
or turkeys, but can also be used for cooking foods that are prone to flare-ups or for smoking foods. Lower
temperatures and slower cooking times result in tender foods.
Rear Burner Use (If Equipped): Remove the warming rack prior to use. Cooking grids should also be removed
if they interfere with the rotisserie. The rear burner is designed to be used in conjunction with the rotisserie
kit (included with most rear burner units) available from your dealer. See the rotisserie kit assembly instructions.
To use the counterbalance - remove the rotisserie motor from the gas grill. Place the spit with meat being
cooked across the hangers inside the grill. The meat will naturally hang with the heavy side down. Tighten
the counterbalance arm and weight so the arm is facing up. Slide the counterweight in or out to balance the
load and tighten in place. Re-install the motor and begin cooking. Place a metal dish underneath the meat to
collect drippings for basting and naturally delicious gravy. Basting liquid may be added as required. To seal in
juices, first operate rear burner on high until brown, then reduce the heat to thoroughly cook foods. Keep the
lid closed for best results. Your roasts and fowl will brown perfectly on the outside and stay moist and tender
on the inside. For example, a 3 pound chicken on the rotisserie will be done in approximately 1½ hours on
medium to high. See ‘Your all Season Grill’ cookbook by Napoleon for more detailed instructions.
WARNING! Barbecue sauce and salt can be corrosive and will cause rapid deterioration of the gas grill
components unless cleaned regularly. When finished cooking disassemble rotisserie components, wash
thoroughly with warm soapy water and store indoors.
Flame Side Burner Use (if equipped): The side burner can be used like any stove top burner, for gravies, soups
etc. For best performance, the gas grill should be located with the side burner protected from the wind.
WARNING! Never grill food directly on the side burner grate.
It is designed for use with pots and pans
only.
Infrared Side Burner Use(if equipped): The gas grill should be located so that the side burner is protected from
the wind, because the wind will adversely affect its performance. The side burner lid needs to be removed
when cooking. Place the lid in the enclosure door.
The side burner is equipped with a cast iron cooking grid which can be positioned at two different heights. The
lower position can be used like any range top burner, for gravies, soups, etc. The higher position is for searing
meats. (see instructions located on side burner lid).
WARNING! Do not close the side burner lid while it is operating or hot.
WARNING! Do not adjust cooking grid while hot or operating.
WARNING! Do not use side burner to deep fry foods as cooking with oil can create a dangerous situation.
www.ultrachefgrills.com
9
1. Follow the infrared side burner lighting instructions and operate on high for 5 minutes with the lid opened
or until the ceramic burners glow red.
2. Place food on grills and cook according to times listed in the Infrared Grilling Chart.
3. Depending upon your taste, continue cooking over infrared burners on high, medium or low, turning food
frequently, or place food on the main burner area of the grill, close lid, and allow oven temperature to slowly
finish cooking your food.
CAUTION! Due to the intense heat the infrared burners provide, food left unattended over burners will
burn quickly. Keep the lid open when cooking with the infrared burners on high. The intense heat ensures
adequate searing temperatures even with the lid open. This also allows observation of the food, so as to
prevent burning.
Protection Of Your Infra Red Burners: The infrared burners of your grill are designed to provide a long service
life. However, there are steps you must take to prevent cracking of their ceramic surfaces, which will cause the
burners to malfunction.
•
Never let water come in direct contact with your ceramic burner.
•
Do not allow hard objects to impact the infra red burner.
•
Do not allow cold water (rain, sprinkler, hose, etc.) to come in contact with hot ceramic burners. A large
temperature differential can cause cracking of the ceramic tile.
•
Damage caused by failure to follow these steps is not covered by your grill warranty.
Replacement Screen N565-0002
Infrared Heat
Most people don’t realize that the heat source we are most familiar with, our sun, warms the earth using
mainly infrared energy. This is a form of electro-magnetic energy with a wavelength just greater than the red
end of the visible light spectrum but less than a radio wave. This energy was discovered in 1800 by Sir William
Herschel who dispersed sunlight into its component colors using a prism. He showed that most of the heat in
the beam fell into the spectral region just beyond the red end of the spectrum, where no visible light existed.
Most materials readily absorb infrared energy in a wide range of wavelengths, causing an increase in its
temperature. The same phenomenon causes us to feel warmth when we are exposed to sunlight. The infrared
rays from the sun travel through the vacuum of space, through the atmosphere, and penetrate our skin. This
causes increased molecular activity in the skin, which creates internal friction and generates heat, allowing us
to feel warmth.
Foods cooked over infrared heat sources are heated by the same principle. Charcoal grilling is our most familiar
choice for infrared cooking. The glowing briquettes emit infrared energy to the food being cooked with very
little drying effect. Any juices or oils that escape from the food drip onto the charcoal and vaporize into smoke
giving the food its delicious grilled taste. The Napoleon infrared burner cooks in the same way. In each burner,
10,000 ports – each with its own tiny flame – cause the surface of the ceramic tile to glow red. This glow emits
the same type of infrared heat to the food as charcoal, without its hassle or mess. Infrared burners
also provide a more consistently heated area that is far easier to regulate than a charcoal fire. For instant
searing, the burners can be set to high, yet they can also be turned down for slower cooking. We all know how
difficult that is on a charcoal fire. Traditional gas burners heat the food in a different way. The air surrounding
the burner is heated by the combustion process and then rises to the food being cooked. This generates
lower grill temperatures that are ideal for more delicate cuisine such as seafood or vegetables, whereas
Napoleon’s infrared burners produce searing heat for juicier, tastier steaks, hamburgers and other meats. For
cooking times and tips refer to the Infrared Grilling Chart.
www.ultrachefgrills.com
10
Infrared Grilling Chart
Food
Control Setting
Cooking Time
Helpful Suggestions
Steak
High setting 2 min. each side.
4 min. – Rare
1 in. thick
High setting 2 min. each side
6 min. – Medium
When selecting meat for grilling,
ask for marbled fat distribution.
The fat acts as a natural tenderizer
while cooking and keeps it moist
and juicy.
then medium setting.
High setting 2 min. each side
8 min. – Well done
then medium setting.
Hamburger
High setting 2 min. each side.
4 min. – Rare
1/2 in. thick
High setting 2 1/2 min. each
side.
5 min. – Medium
6 min. – Well done
High setting 3 min. each side.
Chicken pieces
High setting 2 min. each side.
20-25 min.
The joint connecting the thigh
and the leg from the skinless side
should be sliced 3/4 of the way
though for the meat to lay flatter
on the grill. This helps it to cook
faster and more evenly. To add a
trademark taste to your cooking,
try adding mesquite-flavoured
woodchips to your Napoleon
woodchip smoker.
then medium-low to low setting.
Pork chops
Medium
6 min. per side
Trim off the excess fat before
grilling. Choose thicker chops for
more tender results.
Spare ribs
High setting for 5 minutes
20 min. per side
low to finish
turn often
Choose ribs that are lean and
meaty. Grill until meat easily pulls
away from the bone.
High setting for 5 minutes
15 min. per side
Trim off the excess fat before grilling.
Choose extra thick chops for more
tender results.
4-6 min.
Select the larger size wieners. Slit
the skin lengthwise before grilling.
Lamb chops
medium to finish
Hot dogs
www.ultrachefgrills.com
Preparing hamburgers to order
is made easier by varying the
thickness of your patties. To add
an exotic taste to your meat, try
adding hickory-flavored woodchips
to Napoleon’s woodchip smoker.
Medium - Low
11
Maintenance / Cleaning Instructions
We recommend this gas grill be thoroughly inspected and serviced annually by a qualified service person.
Warning! Always wear protective gloves and safety glasses when cleaning your grill.
Warning! To avoid the possibility of burns, maintenance should be done only when the grill is cool.
Avoid unprotected contact with hot surfaces. Ensure all burners are turned off. Clean grill in an area where
cleaning solutions will not harm decks, lawns, or patios. Do not use oven cleaner to clean any part of this
gas grill. Do not use a self-cleaning oven to clean cooking grids or any other parts of the gas grill.
Barbecue sauce and salt can be corrosive and will cause rapid deterioration of the gas grill components
unless cleaned regularly.
Note: Stainless steel tends to oxidize or stain in the presence of chlorides and sulfides, particularly in coastal
areas and other harsh environments, such as the warm, highly humid atmosphere around pools and hot tubs.
These stains could be perceived as rust, but can be easily removed or prevented. To provide stain prevention
and removal, wash all stainless steel surfaces every 3-4 weeks or as often as required with fresh water and/or
stainless steel cleaner.
WARNING! Turn off the gas at the source and disconnect the unit before servicing. To avoid the
possibility of burns, maintenance should be done only when the grill is cool. A leak test must be performed
annually and whenever any component of the gas train is replaced or gas smell is present.
Combustion Air Adjustment: (This must be done by a qualified gas installer.) The air shutter is factory set and
should not need adjusting under normal conditions. Under extreme field conditions, adjustments might be
required. When the air shutter is adjusted correctly the flames will be dark blue, tipped with light blue and
occasionally yellow.
•
With too little air flow to the burner, the flames are lazy yellow and can produce soot.
•
With too much air flow, the flames lift erratically and can cause difficulties when lighting.
Adjusting the air shutter:
1. Remove cooking grids and sear plates and leave lid open.
2. Loosen air-shutter lock screw located at the mouth of the burner and open or close air shutter as required.
The normal opening settings are:
Main Tube Burner Propane 5/32” (4mm)
Natural 5/32” (4mm)
*Infra-Red burners have no air adjustment.
3. Light the burners and set to high. Visually inspect burner flames. When the shutters are set correctly, turn
burners off, tighten locking screws, and replace removed parts. Ensure that the insect screens are installed.
Light Blue
Burner
Burner Port
Yellow Tipping
Dark Blue
Approximately
1/2” (13mm)
www.ultrachefgrills.com
12
Grids And Warming Rack: The grids and warming rack are best cleaned with a brass wire brush during the
pre-heating period. Steel wool can be used for stubborn stains. It is normal that stainless grids (if equipped)
will discolor permanently from regular usage due to the high temperature of the cooking surface.
Cast Iron Cooking Grids: The cast iron cooking grids supplied with your new grill offer superior heat retention
and distribution. By regularly seasoning your grids you are adding a protective coating, which will aid in resisting
corrosion and increase your grids non-stick capabilities.
First Time Use: Wash the cooking grids by hand with mild dish soap and water to remove any residue from
the manufacturing process (never wash in a dish washer). Rinse thoroughly with hot water and dry completely
with a soft cloth. This is important to avoid moisture from entering the cast iron.
Seasoning: Using a soft cloth, spread VEGETABLE SHORTENING over the entire grid surface ensuring all grooves
and corners are covered. Do not use salted fats such as butter or margarine. Pre-heat your grill for 15 minutes,
then place the seasoned cooking grids in the grill. Turn the burner control knobs to medium with the lid
closed. Allow the cooking grids to heat for approximately one-half hour. Turn all the burners to the “OFF”
position and turn the gas off at the source. Let the cooking grids stand until cool. This procedure should be
repeated several times throughout the season, although it is not required for daily use (follow daily usage
procedure below).
Daily Usage: Before pre-heating, and cleaning with a brass wire grill brush, coat the entire top surface of the
cooking grids with VEGETABLE SHORTENING. Pre-heat the grill and then brush away any unwanted residue
with a brass wire brush.
Stainless Steel Cooking Grids: (upgrade kit available - see replacement parts list). Stainless steel cooking grids
are durable and corrosion resistant. They require less seasoning and maintenance then cast iron cooking grids.
It is recommended that you follow the daily usage procedure listed above although you may find pre-heating
and cleaning your grids with a wire brush is sufficient for your grilling needs.
Control Panel: The control panel text is printed directly on the stainless steel and with proper maintenance
will remain dark and legible. To clean the panel, use only warm soapy water or Continental brand stainless
steel cleaner available from your Ultra Chef dealer. Never apply abrasive cleaners on any stainless surfaces,
especially the printed portion of the control panel or the printing will gradually rub off.
Cleaning Inside The Gas Grill: Remove the cooking grids. Use a brass wire brush to clean loose debris from
the casting sides and underneath the lid. Scrape the sear plates with a putty knife or scraper, and use a wire
brush to remove the ash. Remove the sear plates and brush debris from the burners with the brass wire brush.
Sweep all debris from inside the gas grill into the drip pan.
Lights: To remove the lens from the light housing, insert a flat screwdriver tip between the lens and the housing
and rock it gently. Do not touch the halogen bulb. The oil from your fingertips will reduce the life of the bulb.
To clean the lens, first soak it in hot soapy water, then clean with a rag and non abrasive cleaner. To reinstall
the lens, simply snap it back into the housing.
Drip Pan: Accumulated grease is a fire hazard. Clean the drip pan frequently (every 4 – 5 uses or as often as
required) to avoid grease buildup. Grease and excess drippings pass through to the drip pan, located beneath
the gas grill and accumulate in the disposable grease tray below the drip pan. To access the disposable grease
tray or to clean the drip pan, slide the drip pan free of the grill. Never line the drip pan with aluminum foil,
sand or any other material as this could prevent the grease from flowing properly. The pan should be scraped
out with a putty knife or scraper. Replace the disposable grease tray every 2 – 4 weeks, depending on gas grill
usage. For supplies, see your Napoleon Gas Grill dealer.
Cleaning The Outer Grill Surface: Do not use abrasive cleaners or steel wool on any painted, porcelain or stainless
steel parts of your Napoleon Grill. Doing so will scratch the finish. Exterior grill surfaces should be cleaned with
warm soapy water while the metal is still warm to the touch. To clean stainless surfaces, use a stainless steel or
a non-abrasive cleaner. Always wipe in the direction of the grain. Over time, stainless steel parts discolor when
heated, usually to a golden or brown hue. This discoloration is normal and does not affect the performance of
the grill. Porcelain enamel components must be handled with additional care. The baked-on enamel finish is
glass-like, and will chip if struck. Touch-up enamel is available from your Napoleon Grill dealer.
WARNING! Hose: Check for abrasions, melting, cuts, and cracks in the hose. If any of these conditions
exist, do not use the gas grill. Have the part replaced by your Napoleon Gas Grill dealer or qualified gas
installer.
Tube Burner: The burners are made from heavy wall 304 stainless steel, but extreme heat and a corrosive
environment can cause surface corrosion to occur. This can be removed with a brass wire brush.
CAUTION! Beware of Spiders.
Spiders and insects are attracted to the smell of propane and natural gas. The burner is equipped with an
insect screen on the air shutter, which reduces the likelihood of insects building nests inside the burner but
www.ultrachefgrills.com
13
does not entirely eliminate the problem. A nest or web can cause the burner to burn with a soft yellow or
orange flame or cause a fire (flashback) at the air shutter beneath the control panel. To clean the inside of the
burner, it must be removed from the gas grill: Remove the screw that attaches the burner to the back wall.
Slide the burner back and upwards to remove. Cleaning: Use a flexible venturi tube brush to clean the inside
of the burner. Shake any loose debris from the burner through the gas inlet. Check the burner ports and valve
orifices for blockages. Burner ports can close over time due to cooking debris and corrosion, use an opened paperclip
or the supplied port maintenance bit to clean them. Drill out blocked ports using this drill bit in a small cordless
drill. The ports are easier to clean if the burner is removed from the grill, but it can also be done with the
burner installed. Do not flex the drill bit when drilling the ports, as this will cause the drill bit to break. This drill
is for burner ports only, not for the brass orifices (jets) which regulate the flow into the burner. Take care not to
enlarge the holes. Ensure the insect screen is clean, tight, and free of any lint or other debris.
Reinstallation: Reverse the procedure to reinstall the burner. Check that the valve enters the burner when
installing.
Warning! When reinstalling the burner after cleaning it is very
important that the valve/orifice enters the burner tube before lighting your
gas grill. If the valve is not inside the burner tube a fire or explosion could
occur.
Aluminum Castings: Clean castings periodically with warm soapy water. Aluminum will not rust, but high
temperatures and weathering can cause oxidation to occur on aluminum surfaces. This appears as white spots
on the castings. To refinish these areas, clean first and sand lightly with fine sandpaper. Wipe the surface to
remove any residue and paint with high temperature barbecue paint. Protect surrounding areas from over-spray.
Follow the manufacture’s directions for curing.
Troubleshooting
Problem
Possible Causes
Solution
Low heat / Low flame
when valve turned to
high.
For propane - improper lighting procedure.
Ensure lighting procedure is followed
carefully. All gas grill valves must be in the
off position when the tank valve is turned
on. Turn tank on slowly to allow pressure
to equalize. See lighting instructions.
For natural gas - undersized supply line.
Pipe must be sized according to
installation code.
For both gases - improper preheating.
Preheat grill with both main burners on
high for 10 to 15 minutes.
Sear plates installed incorrectly.
Ensure sear plates are installed with the
holes towards the front and the slots on
the bottom. See assembly instructions.
Improper preheating.
Preheat grill with both main burners on
high for 10 to 15 minutes.
Excessive grease and ash build on sear plates
and in drip pan.
Clean sear plates and drip pan regularly.
Do not line pan with aluminum foil. Refer
to cleaning instructions.
Excessive flare-ups/
uneven heat.
www.ultrachefgrills.com
14
Problem
Possible Causes
Solution
Burners burn with yellow
flame, accompanied by
the smell of gas.
Possible spider web or other debris, or
improper air shutter adjustment.
Thoroughly clean burner by removing.
See general maintenance instructions.
Open air shutter slightly according to
combustion air adjustment instructions.
(This must be done by a qualified gas
installer.)
Flames lift away from
burner, accompanied
by the smell of gas, and
possibly difficulties in
lighting.
Improper air shutter adjustment.
Close air shutter slightly according to
combustion air adjustment instructions.
(This must be done by a qualified gas
installer.)
Humming regulator.
Normal occurrence on hot days.
This is not a defect. It is caused by internal
vibrations in the regulator and does not
affect the performance or safety of the
gas grill. Humming regulators will not be
replaced.
Burners will not cross
light each other.
Plugged ports at back of burner.
Clean burner ports. See burner
maintenance instructions.
“Paint” appears to be
Grease build-up on inside surfaces.
peeling inside lid or hood.
This is not a defect. The finish on the lid
and hood is porcelain, and will not peel.
The peeling is caused by hardened grease,
which dries into paint-like shards, that
flake off. Regular cleaning will prevent this.
See cleaning instructions.
Infrared burner (if
equipped) flashes back
(during operation the
burner abruptly makes
a loud “whoosh” sound,
followed by a continuous
blow-torch type sound
and grows dim.)
Ceramic tiles overloaded with grease drippings
and build-up. Ports are clogged.
Turn burner off and allow to cool for at
least two minutes. Relight burner and
burn on high for at least five minutes or
until the ceramic tiles are evenly glowing
red.
Burner overheated due to inadequate
ventilation (too much grill surface covered by
griddle or pan.)
Ensure that no more than 75% of the
grill surface is covered by objects or
accessories. Turn burner off and allow to
cool for at least two minutes, then relight.
Cracked ceramic tile.
Allow burner to cool and inspect very
closely for cracks. If any cracks are found,
contact your authorized Napoleon dealer
to order a replacement burner assembly.
Leaking gasket surrounding the ceramic tile, or
a weld failure in the burner housing.
Contact your authorized Napoleon dealer
for instructions on ordering a replacement
burner assembly.
www.ultrachefgrills.com
15
KEEP YOUR RECEIPT AS PROOF OF PURCHASE TO VALIDATE YOUR WARRANTY.
Ordering Replacement Parts
Warranty Information
MODEL:
DATE OF PURCHASE:
SERIAL NUMBER:
(Record information here for easy reference)
Before contacting the Customer Care Department, check the NAC Website for more extensive cleaning, maintenance,
troubleshooting and parts replacement instructions at www. ultrachefgrills.com. Contact the factory directly
for replacement parts and warranty claims. Our Customer Care Department is available between 9 AM and
5 PM (Eastern Standard Time) at 1-866-820-8686 or fax at 1-705-727-4282. To process a claim, we must be
provided with the following information:
1. Model and serial number of the unit.
2. Part number and description.
3. A concise description of the problem (‘broken’ is not sufficient).
4. Proof of purchase (photocopy of the invoice).
In some cases the Customer Care Representative could request to have the parts returned to the factory for
inspection before providing replacement parts. These parts must be shipped prepaid to the attention of the
Customer Care Department with the following information enclosed:
1. Model and serial number of the unit.
2. A concise description of the problem (‘broken’ is not sufficient).
3. Proof of purchase (photocopy of the invoice).
4. Return Authorization Number - provided by the Customer Care Representative.
Before contacting customer care, please note that the following items are not covered by the warranty:
Costs for transportation, brokerage or export duties.
Labor costs for removal and reinstallation.
Costs for service calls to diagnose problems.
Discoloration of stainless steel parts.
Part failure due to lack of cleaning and maintenance, or use of improper cleaners (oven cleaner).
www.ultrachefgrills.com
16
Caution! During unpacking and assembly we recommended you wear work gloves and safety glasses
for your protection. Although we make every effort to make the assembly process as problem free and
safe as possible, it is characteristic of fabricated steel parts that the edges and corners might be sharp and
could cause cuts if handled incorrectly.
Getting Started
1. Remove all cart panels, hardware, and grill head from carton. Raise lid and remove any components
packed inside. Use the parts list to ensure all necessary parts are included.
2. Do not destroy packaging until the grill has been fully assembled and operates to your satisfaction.
3. Assemble the grill where it is to be used, lay down cardboard or a towel to protect parts from being lost or
damaged while assembling.
4. Most stainless steel parts are supplied with a protective plastic coating that must be removed prior to
using grill.
5. Follow all instructions in the order that they are laid out in this manual.
6. Two people are required to lift the grill head onto the assembled cart.
If you have any questions about assembly or grill operation, or if there are damaged or missing parts please
call our Customer Care Department at 1-866-820-8686 between 9 AM and 5 PM (Eastern Standard Time).
TOOLS REQUIRED FOR ASSEMBLY (tools not included)
3/8 (10mm)
Wrench,
ratchet or driver
www.ultrachefgrills.com
Flat and Philips
screwdrivers
Pliers
Hammer
17
1 X N430-0002
1. Magnet Installation
Snap magnet into slot in front of bottom shelf.
16 X N570-0073 (1/4-20 X 3/8”)
16 X N450-0027 (1/4-20)
3/8”(10mm) 7/16”(11mm)
2. Caster/Bracket Installation
Attach (4) casters, using (4) ¼ -20 x 3/8” screws and (4) ¼ -20 lock nuts for each caster. Attach brackets under front casters
as illustrated. Tighten securely.
non relvolving caster- left side
www.ultrachefgrills.com
18
Propane Only
3. Propane Tank Ring Installation
Insert propane tank ring into slots in bottom of shelf as shown. Fold tabs over to secure in place.
4 x N570-0080 (#14 x 1/2”)
3/8”(10mm)
4. Left and Right Cart Panel Installation
Install end cart panels ensuring slots in panel are to the top, rest panel on bottom shelf and line up holes. Fasten using
(4) #14 x 1/2” screws.
www.ultrachefgrills.com
19
6 x N570-0080 (#14 x 1/2”)
6 x N570-0078 (M4 X 8mm)
6 x N450-0032 (M4 LOCK NUTS)
3/8”(10mm)
5. Transformer/Rear Cart Panel Installation
Install the transformer and the power bar onto the rear panel as illustrated using (6) M4 x 8mm screws and (6) M4 lock nuts.
Route the power cord through the rubber grommet in the rear panel.
Fit the rear cart panel between the two end panels; ensure the large holes in the rear panel are to the bottom of cart as
illustrated. Fasten using (6) #14 x 1/2” screws, three on each side.
485RSIB MODEL
Ensure power
bar is installed
with covers to
the top.
www.ultrachefgrills.com
20
1 x N570-0080 (#14 x 1/2”)
3/8”(10mm)
6. Tank Inhibitor Bracket / Propane Tank Mount Installation
Insert tank inhibitor bracket into slot in rear panel as illustrated. Fasten to bottom panel using (1) #14 x 1/2” screw. Clip top
propane tank mount into slots in back panel. Insert one end at a time, gently bending wire. (When not in use tank mount
will lay flat against back panel).
Propane Only
www.ultrachefgrills.com
21
4 x N570-0080 (#14 x 1/2”) 1 X N430-0002
3/8”(10mm)
7. Front Cabinet Support Installation
Fasten top rail assembly to the front of side panels using (4) #14 x 1/2” screws. For ease of installation start all screws
before tightening completely. Snap magnet into place as shown.
4 x N570-0080 (#14 x 1/2”)
3/8”(10mm)
8. Heat Shield Installation
Attach heat shield above propane tank ring using (4) #14 x 1/2» screws. Attach one end under lip of back panel and other
end to underside of front cabinet support.
www.ultrachefgrills.com
22
4 x N570-0091 (1/4-20 X 1/2”)
3/8”(10mm)
9. Grill Head Installation
L485RSIB MODELS - Are equipped with internal lights. To avoid assembly difficulties, prior to mounting grill head
remove the zip tie holding the wire connectors in place. (Take care when removing the tie not to damage the wires).
Ensure the wires drop inside the cart and do not become pinched between the grill head and the cabinet when mounting
the grill head.
PROPANE ONLY - To avoid assembly difficulties, prior to mounting the grill head, remove zip tie holding regulator
up under control panel. This was installed at the factory to protect the regulator hose during shipping and is no longer
required. (Take care when removing the tie not to damage the hose). Ensure the regulator drops into the small opening,
between the tank heat shield and the right side of the cabinet.
Lift grill head and place on assembled cart, lining up holes in top of side cart panels with holes in bottom of base. Fasten
from inside using (4) 1/4-20 x 1/2” screws, two per side.
Two people are required for this step.
Correct Assembly
www.ultrachefgrills.com
Incorrect Assembly
23
2 x N570-0073 (1/4-20 X 3/8”)
1 x N640-0001
3/8”(10mm)
10. Transformer / Rotisserie Mount Installation (RSIB MODEL)
Connect the two wire connectors from the lights to the two wire connectors coming from the transformer. Install rotisserie
mount bracket to left side of barbecue as shown using (2) 1/4 – 20 x 3/8” screws.
Battery Pack / Rotisserie Mount Installation (RSB MODEL)
Install battery pack below vent slots on left hand panel using magnet supplied with battery pack. Plug wire from LED
(lights) located underneath control panel into wire from battery pack. Install rotisserie mount bracket to left side of
barbecue as shown using (2) 1/4 – 20 x 3/8” screws.
Clip wires from lights
to side panel using
retainer clip supplied.
485RSIB MODEL
www.ultrachefgrills.com
24
4 x N570-0080 (#14 x 1/2”)
4 x N570-0088 (10-24 X 1/2”)
4 x N735-0007 (1/4”)
3/8”(10mm)
485/485RSB MODEL
11. Assembling Handles to Side Shelf
Peel protective coating from side shelf. Attach a handle to the front of each side shelf as shown using (2) #14 X 1/2” screws.
Fasten the supplied tool pegs to the side of each side shelf using (2) 10-24 X 1/2” screws and (2) 1/4” washers.
WARNING! Do not over tighten screws, as this will cause the handle to crack.
8 x N570-0073 (1/4-20 X 3/8”)
3/8”(10mm)
485RSIB MODEL
11. Assembling Handles to Side Shelf
Peel protective coating from side shelf. Attach handles to side shelf as shown using (8) 1/4-20 x 3/8” screws.
Tabs located on either side of ice bucket
must engage notches in side shelf.
www.ultrachefgrills.com
25
4 x N570-0082 (1/4-20 X 5/8”)
4 x N735-0001 (insulated washer)
3/8”(10mm)
12. Side Shelf Installation
Insert (4) ¼-20 x 5/8” screws through the washers into the threaded holes in the side of the base; do not tighten all the way.
Slide the assembled side shelf over the screw heads and finish tightening.
4 x N570-0082 (1/4-20 X 5/8”)
4 x N735-0001 (insulated washer)
1 x N160-0016 (clip)
3/8”(10mm)
13. Side Burner Installation
Insert (4) ¼-20 x 5/8” screws through the washers into the threaded holes in the side of the base; do not tighten all the way.
Slide the assembled side burner over the screw heads and finish tightening. Fit the orifice into the burner tube and secure
with the hose retainer clip supplied. Attach the wire from the manifold to the side burner electrode.
485RSIB MODEL
Fit orifice into burner
tube and secure with hose
retainer clip supplied.
WARNING! The Infrared side burner
is supplied with a drip pan which holds
only a minimal amount of grease. To
prevent grease fires, the pan must be
cleaned after each use.
www.ultrachefgrills.com
26
4 x N570-0082 (1/4-20 X 5/8”)
4 x N735-0001 (insulated washer)
1 x N160-0016 (clip)
3/8”(10mm)
13. Side Burner Installation
Insert (4) ¼-20 x 5/8” screws through the washers into the threaded holes in the side of the base; do not tighten all
the way. Slide the assembled side burner over the screw heads and finish tightening. Fit the orifice into the burner
tube and secure with the hose retainer clip supplied. Attach the wire from the manifold to the side burner electrode.
485RSB MODEL
Fit orifice into burner
tube and secure with hose
retainer clip supplied.
www.ultrachefgrills.com
27
4 x N570-0080 (#14 x 1/2”)
2 x N105-0011 (door bushing)
3/8”(10mm)
14. Cabinet Door Installation
Install door handle onto front of door using (2) #14 x 1/2” screws per door.
Insert pivot rod through hole on inside top of door. Holding door in one hand, direct pivot rod into hole in underside of
front cabinet support. Once secure, let rod slide down and through hole in bottom of door and into bushing in bottom shelf.
Warning! Do not over tighten screws, as this will cause the handle to crack.
Bushing
www.ultrachefgrills.com
28
15. Sear Plate Installation
Insert sear plates into base, position one over each tube burner with slots down to allow drippings to travel through.
16. Grids and Warming Rack Installation
Position grids and warming rack into base as shown. Rest warming rack on brackets inside hood and grids on front and back
lip of base.
www.ultrachefgrills.com
29
17. Grease Tray and Holder Installation
Clip the wire grease tray holder into the two holes located in the center of the back panel. Place the aluminum grease
tray into the grease tray holder.
disposable grease tray
18. Drip Pan Installation
Slide drip pan into rear of base as shown. Ensure dip pan rides along rails on bottom of base.
www.ultrachefgrills.com
30
Rotisserie Kit Assembly Instruction
(rotisserie kit is optional)
Assemble rotisserie kit components as shown.
Ensure stop bushing is
tightened on the inside
of hood casting.
www.ultrachefgrills.com
31
Providing Power To Your Grill
(485RSIB MODEL ONLY)
CAUTION! To ensure protection against electric shock, use only a Ground Fault Interrupter (GFI)
protected circuit with this outdoor gas cooking appliance.
To provide power to your grill, plug a grounded electrical cord into the electrical box installed in the rear panel
of your grill as shown.
•
Ensure the cord is approved and marked for OUTDOOR USE.
•
Do not immerse cord or plugs in water or other liquid.
•
Keep electrical cords out of pathways.
•
Do not let the cord hang over the edge of a table or touch hot surfaces.
To provide power to the internal lights, plug the transformer cord into the electrical box installed in the rear
panel of your gill as shown. The light switch located on the control panel allows you to easily turn the internal
lights on and off.
To provide power to the optional rotisserie kit, plug the rotisserie motor into the electrical box installed in the
rear panel of your grill as shown.
To Rotisserie Motor
To Transformer
Power Supply
www.ultrachefgrills.com
32
1 x N640-0001
Propane Only – Proper Hose Connection
Ensure the regulator drops into the
small opening, between the tank heat
shield and the right side of the cabinet.
Clip hose to side
panel using hose
retainer clip supplied.
Propane Only – Improper Hose Connection
WARNING – FIRE HAZARD
The regulator must be attached so that no
part of the hose touches the underside of
the grill or drip pan. A fire will result if these
directions are ignored.
www.ultrachefgrills.com
33
3/4”(19mm)
1 x N640-0001
Natural Gas Only – Proper Hose Connection
WARNING! The installation must be performed by a licensed gas fitter, and all connections must be
leak tested before operating the grill. Do not use pipe dope or teflon tape on this connection.
Clip hose to side
panel using hose
retainer clip supplied.
Bushing is pre-installed at factory.
www.ultrachefgrills.com
34
Natural Gas Only – Improper Hose Connection
WARNING – FIRE HAZARD
WARNING! Do not route hose underneath drip pan.
WARNING! Do not route hose over top of rear panel.
WARNING! Ensure the hose does not contact any high temperature surfaces, or it may melt and leak
causing a fire.
www.ultrachefgrills.com
35
Leak Testing Instructions
WARNING! A leak test must be performed annually and each time a cylinder is hooked up or if a part
of the gas system is replaced.
Warning! Never use an open flame to check for gas leaks. Be certain no sparks or open flames are in
the area while you check for leaks. Sparks or open flames will result in a fire or explosion, damage to property,
serious bodily injury, or death.
Leak testing: This must be done before initial use, annually, and whenever any gas components are replaced
or serviced. Do not smoke while performing this test, and remove all sources of ignition. See Leak Testing
Diagram for areas to check. Turn all burner controls to the off position. Turn gas supply valve on.
Brush a half-and-half solution of liquid soap and water onto all joints and connections of the regulator, hose,
manifolds and valves.
Bubbles will indicate a gas leak. Either tighten the loose joint or have the part replaced with one recommended
by the Napoleon Customer Care department and have the grill inspected by a certified gas installer.
If the leak cannot be stopped, immediately shut off the gas supply, disconnect it, and have the grill inspected
by a certified gas installer or dealer. Do not use the grill until the leak has been corrected.
www.ultrachefgrills.com
36
485 Parts List
Item
Part #
Description
485
1
N135-0030G
lid side casting left
x
2
N135-0031G
lid side casting right
x
3
N335-0061K
black lid insert
x
N335-0060
stainless steel lid insert
x
4
N585-0066
lid heat shield - stainless steel only
x
5
N510-0010
black silicone lid bumper
x
6
N685-0007
temperature gauge
x
9
N010-0652
lid handle
x
10
N080-0252G
lid handle cover
x
11
N570-0015
lid pivot screw
x
12
N570-0073
1/4-20 x 3/8" screw
x
13
N735-0003
1/4" lockwasher
x
14
N570-0080
#14 x 1/2" screw
x
15
N570-0013
#8 x 5/8" screw
x
16
N520-0028K
warming rack
x
17
N475-0270K
base insert right
x
18
N035-0101
base side right
x
19
N570-0093
screw M4 x 8mm"
x
20
N450-0032
M4 lock nut
x
21
N035-0102K
base insert rear
x
22
N200-0093S
rear corner cover base
x
23
N570-0008
#8 x 1/2" screw
x
24
N475-0269K
base insert left
x
25
N035-0100
base side left
x
26
N475-0267
rotisserie mount
x
27
N305-0063
cooking grids - cast iron
x
N370-0597
cooking grids - stainless steel upgrade kit
ac
28
N305-0057K
sear plate
x
29
N080-0250
main burner support
x
30
N100-0036
main burner
x
31
N215-0008
grease deflector base
x
32
N010-0501-M08
drip pan
x
33
N735-0001
insulated washer
x
34
N570-0082
1/4-20 x 5/8" screw
x
35
N010-0643S
side shelf left
x
36
N340-0006
tool hook side shelf
x
37
N570-0088
screw 10-24 x 1/2"
x
N735-0007
1/4" washer
x
38
N380-0016R
control knob
x
39
N051-0006
control knob bezel
x
40
N010-0542
manifold assembly c/w valves
P
N010-0543
manifold assembly c/w valves
n
41
N120-0011
end cap control panel left
x
42
N585-0065
base heat shield
x
43
N035-0103K
base insert front
x
44
N120-0012
end cap control panel right
x
www.ultrachefgrills.com
37
485 Parts List
Item
Part #
Description
485
45
N325-0062
side shelf handle
x
46
N475-0265
control panel
x
47
N655-0124S
front cabinet support
x
48
N475-0183S
left/right side panel cabinet enclosure
x
49
N160-0014
grease tray holder
x
50
N185-0001
grease tray foil
x
N710-0062
grease tray aluminium
ac
52
N475-0271S
rear cart panel
x
53
N160-0015
propane tank clip
p
54
N080-0254S
propane tank inhibitor bracket
p
55
N555-0036
door pivot rod
x
56
N010-0637S
cart door assembly
x
57
N105-0011
door bushings
x
58
N570-0080
#14 x 1/2" screw
x
59
N570-0073
1/4-20 x 3/8" screw
x
60
N450-0027
locking nut 1/4-20
x
61
N080-0212S
stabilizer brackets
x
62
N130-0013
non revolving caster
x
63
N130-0012
revolving caster
x
64
N585-0064P
heat shield
x
65
N590-0147S
bottom shelf
x
66
N430-0002
magnetic catch
x
67
N255-0027
union fitting 3/8" - 3/8"
x
68
N720-0044
manifold flex connector
x
69
N655-0094P
tank ring support
p
71
N010-0647S
side shelf right
x
72
N530-0003
1-outlet regulator
p
N345-0001
10ft n/g hose c/w quick disconnect
n
73
N640-0001
hose retainer clip
x
74
N105-0013
bushing
x
75
N725-0034
main burner valve c/w #56 orifice
p
N725-0035
main burner valve c/w 1.65mm orifice
n
76
N570-0091
1/4-20 x 1/2" screw -sharp
x
77
N570-0092
screw 10-24 x 1/4"
x
N370-0585
main assembly blister pack
x
64485
rotisserie kit
ac
63488
vinyl cover
ac
56018
stainless steel griddle
ac
67731
charcoal tray
ac
62007
replacement grease trays foil (5 pieces)
ac
p - propane units only
x - standard
n - natural gas units only ac - accessory
www.ultrachefgrills.com
38
485 PARTS DIAGRAM
www.ultrachefgrills.com
39
485RSB Parts List
Item
Part #
Description
485RSB
1
N135-0030G
lid side casting left
x
2
N135-0031G
lid side casting right
x
3
N335-0061K
black lid insert
x
N335-0060
stainless steel lid insert
x
4
N585-0066
lid heat shield - stainless steel only
x
5
N510-0010
black silicone lid bumper
x
6
N685-0007
temperature gauge
x
9
N010-0652
lid handle
x
10
N080-0252G
lid handle cover
x
11
N570-0015
lid pivot screw
x
12
N570-0073
1/4-20 x 3/8" screw
x
13
N735-0003
1/4" lockwasher
x
14
N570-0080
#14 x 1/2" screw
x
15
N570-0013
#8 x 5/8" screw
x
16
N520-0028K
warming rack
x
17
N475-0270K
base insert right
x
18
N035-0101
base side right
x
19
N570-0093
screw M4 x 8mm
x
20
N450-0032
M4 lock nut
x
21
N035-0104K
base insert rear
x
22
N200-0093S
rear corner cover base
x
23
N570-0008
#8 x 1/2" screw
x
24
N475-0269K
base insert left
x
25
N035-0100
base side left
x
26
N475-0267
rotisserie mount
x
27
N305-0063
cooking grids - cast iron
x
N370-0597
cooking grids - stainless steel upgrade kit
ac
28
N305-0057K
sear plate
x
29
N080-0250
main burner support
x
30
N100-0036
main burner
x
31
N215-0008
grease deflector base right
x
32
N010-0501-M08
drip pan
x
33
N735-0001
insulated washer
x
34
N570-0082
1/4-20 x 5/8" screw
x
35
N010-0643-M06
side shelf left
x
36
N340-0006
tool hook side shelf
x
37
N570-0088
screw 10-24 x 1/2"
x
N735-0007
1/4" washer
x
38
N380-0016
control knob
x
39
N051-0006
control knob bezel
x
40
N010-0644
manifold assembly c/w valves
P
N010-0645
manifold assembly c/w valves
n
41
N120-0011
end cap control panel left
x
42
N585-0065
base heat shield
x
43
N035-0103K
base insert front
x
44
N120-0012
end cap control panel right
x
www.ultrachefgrills.com
40
485RSB Parts List
Item
Part #
Description
485RSB
45
N325-0062
side shelf handle
x
46
N475-0266
control panel
x
47
N655-0124S
front cabinet support
x
48
N475-0183S
left/right side panel cabinet enclosure
x
49
N160-0014
grease tray holder
x
50
N185-0001
grease tray foil
x
N710-0062
grease tray aluminium
ac
52
N475-0271S
rear cart panel
x
53
N160-0015
propane tank clip
p
54
N080-0254S
propane tank inhibitor bracket
p
55
N555-0036
door pivot rod
x
56
N010-0637-M06
cart door assembly
x
57
N105-0011
door bushings
x
58
N570-0080
#14 x 1/2" screw
x
59
N570-0073
1/4-20 x 3/8" screw
x
60
N450-0027
locking nut 1/4-20
x
61
N080-0212S
stabilizer brackets
x
62
N130-0013
non revolving caster
x
63
N130-0012
revolving caster
x
64
N585-0064P
heat shield
x
65
N590-0147S
bottom shelf
x
66
N430-0002
magnetic catch
x
67
N255-0027
union fitting 3/8" - 3/8"
x
68
N720-0044
manifold flex connector
x
69
N655-0094P
tank ring support
p
71
N010-0642-M06
side shelf right
x
72
N530-0003
1-outlet regulator
p
N345-0001
10ft n/g hose c/w quick disconnect
n
73
N640-0001
hose retainer clip
x
74
N105-0013
bushing
x
75
N725-0034
main burner valve c/w #56 orifice
p
N725-0035
main burner valve c/w 1.65mm orifice
n
76
N725-0040
rear burner valve
p
N725-0041
rear burner valve
n
77
N660-0002
switch light
x
78
N357-0013
side burner igniter
x
79
N500-0041K
side burner plate
x
80
N570-0092
screw 10-24 x 1/4"
x
82
N100-0037
side burner
x
N720-0055
side burner supply tube
x
N750-0016
side burner igniter lead
x
83
N305-0059
side burner grate
x
84
N485-0009
push pin
x
85
N335-0048-M06
side burner lid
x
86
N105-0001
bushing 7/8"
x
87
N455-0062
side burner orifice #60
p
www.ultrachefgrills.com
41
485RSB Parts List
Item
Part #
Description
485RSB
N455-0063
side burner orifice 1.45 mm
n
N725-0040
side burner valve
p
N725-0041
side burner valve
n
88
N160-0016
side burner hose/orifice retainer clip
x
89
N570-0091
1/4-20 x 1/2" screw -sharp
x
90
N190-0001
battery pack
x
W043-0002
battery "AA'
x
91
N750-0020B
wiring harness led
x
92
N010-0660P
infra red rear burner
p
N010-0660N
infra red rear burner
n
N455-0054
rear burner orifice #59
p
N455-0053
rear burner orifice #53
n
N720-0053
rear burner supply tube
x
N010-0651
grease deflector base left
x
93
94
N585-0068
rear burner rain shield
x
N370-0585
main assembly blister pack
x
64485
rotisserie kit
ac
63488
vinyl cover
ac
56018
stainless steel griddle
ac
67731
charcoal tray
ac
62007
replacement grease trays foil (5 pieces)
ac
p - propane units only
n - natural gas units only x - standard
ac - accessory
www.ultrachefgrills.com
42
485RSB PARTS DIAGRAM
www.ultrachefgrills.com
43
485RSIB Parts List
Item
Part #
Description
485RSIB
1
N135-0030G
lid side casting left
x
2
N135-0031G
lid side casting right
x
3
N335-0061K
black lid insert
x
N335-0060
stainless steel lid insert
x
4
N585-0066
lid heat shield - stainless steel only
x
5
N510-0010
black silicone lid bumper
x
6
N685-0007
temperature gauge
x
9
N010-0652
lid handle
x
10
N080-0252G
lid handle cover
x
11
N570-0015
lid pivot screw
x
12
N570-0073
1/4-20 x 3/8" screw
x
13
N735-0003
1/4" lockwasher
x
14
N570-0080
#14 x 1/2" screw
x
15
N570-0013
#8 x 5/8" screw
x
16
N520-0028K
warming rack
x
17
N475-0270K
base insert right
x
18
N035-0101
base side right
x
19
N570-0093
screw M4 x 8mm
x
20
N450-0032
lock nut M4
x
21
N035-0105K
base insert rear
x
22
N200-0092S
rear cover base
x
23
N570-0008
#8 x 1/2" screw
x
24
N475-0269K
base insert left
x
25
N035-0100
base side left
x
26
N475-0267
rotisserie mount
x
27
N305-0063
cooking grids - cast iron
x
N370-0597
cooking grids - stainless steel upgrade kit
ac
28
N305-0057-M05
sear plate
x
29
N080-0250
main burner support
x
30
N100-0036
main burner
x
31
N215-0008
grease deflector base right
x
32
N010-0501-M08
drip pan
x
33
N735-0001
insulated washer
x
34
N570-0082
1/4-20 x 5/8" screw
x
35
N010-0641-M06
side shelf left
x
36
N340-0006
tool hook side shelf
x
37
N570-0073
1/4-20 x 3/8" screw
x
38
N380-0016
control knob
x
39
N051-0006
control knob bezel
x
40
N010-0644
manifold assembly c/w valves
P
N010-0645
manifold assembly c/w valves
n
41
N120-0011
end cap control panel left
x
42
N585-0065
base heat shield
x
43
N035-0103K
base insert front
x
44
N120-0012
end cap control panel right
x
45
N325-0062
door handle
x
www.ultrachefgrills.com
44
485RSIB Parts List
Item
Part #
Description
485RSIB
46
N475-0283
control panel
x
47
N655-0124S
front cabinet support
x
48
N475-0183S
left/right side panel cabinet enclosure
x
49
N160-0014
grease tray holder
x
50
N185-0001
grease tray foil
x
N710-0062
grease tray aluminium
ac
52
N475-0271S
rear cart panel
x
53
N160-0015
propane tank clip
p
54
N080-0254S
propane tank inhibitor bracket
p
55
N555-0036
door pivot rod
x
56
N010-0637-M06
cart door assembly
x
57
N105-0011
door bushings
x
58
N570-0080
#14 x 1/2" screw
x
59
N570-0073
1/4-20 x 3/8" screw
x
60
N450-0027
locking nut 1/4-20
x
61
N080-0212S
stabilizer brackets
x
62
N130-0013
non revolving caster
x
63
N130-0012
revolving caster
x
64
N585-0064P
heat shield
x
65
N590-0147S
bottom shelf
x
66
N430-0002
magnetic catch
x
67
N255-0027
union fitting 3/8" - 3/8"
x
68
N720-0044
manifold flex connector
x
69
N655-0094P
tank ring support
p
71
N010-0642-M06
side shelf right
x
72
N530-0003
1-outlet regulator
p
N345-0001
10ft n/g hose c/w quick disconnect
n
73
N640-0001
hose retainer clip
x
74
N105-0013
bushing
x
75
N725-0034
main burner valve c/w #56 orifice
p
N725-0035
main burner valve c/w 1.65mm orifice
n
N725-0040
rear burner valve
p
76
N725-0041
rear burner valve
n
77
N660-0002
switch light
x
78
N357-0013
side burner igniter
x
79
N010-0618
side burner plate
x
80
N570-0081
screw 10-24 x 3/8"
x
N240-0026
side burner electrode
x
N010-0659
side burner
x
N565-0002
infra red burner screen
x
N720-0055
side burner supply tube
x
N750-0016
side burner igniter lead
x
83
N305-0072
side burner grate
x
84
N485-0009
push pin
x
85
N335-0048-M06
side burner lid
x
86
N105-0001
bushing 7/8"
x
82
www.ultrachefgrills.com
45
485RSIB Parts List
Item
Part #
Description
485RSIB
87
N455-0062
side burner orifice #60
p
N455-0063
side burner orifice 1.45 mm
n
N725-0040
side burner valve
P
N725-0041
side burner valve
n
88
N160-0016
side burner hose/orifice retainer clip
x
89
N707-0003
transformer lights
x
N175-0002
electrical connector
x
N460-0002
receptacle
x
90
N750-0024
wiring harness transformer
x
91
N750-0023B
wiring harness led
x
92
N010-0660P
infra red rear burner
p
N010-0660N
infra red rear burner
n
N455-0054
rear burner orifice #59
p
N455-0053
rear burner orifice #53
n
N720-0053
rear burner supply tube
x
93
N010-0651
grease deflector base left
x
94
N185-0003
ice bucket
x
95
N325-0059
side shelf handle (side)
x
96
N325-0060
side shelf handle (front)
x
97
N570-0088
screw 10-24 x 1/2"
x
N735-0007
1/4" lockwasher
x
98
N570-0092
screw 10-24 x 1/4"
x
99
N570-0091
screw 1/4-20 x 1/2" -sharp
x
100
N710-0063
side burner drip pan
x
101
N402-0011
light hi-temp left
x
102
N402-0012
light hi-temp right
x
103
N585-0068
rear burner rain shield
x
N370-0585
main assembly blister pack
x
64485
rotisserie kit
ac
63488
vinyl cover
ac
56018
stainless steel griddle
ac
67731
charcoal tray
ac
62007
replacement grease trays foil (5 pieces)
ac
p - propane units only
n - natural gas units only x - standard
ac - accessory
www.ultrachefgrills.com
46
485RSIB PARTS DIAGRAM
www.ultrachefgrills.com
47
ELECTRICAL CIRCUIT DIAGRAM
(FOR MODELS WITH INTERNAL LIGHTS ONLY)
www.ultrachefgrills.com
48
FAX TO: 705 727 4282
ACCESSORIES & PARTS ORDER FORM
PLEASE PRINT CLEARLY
CONTACT NAME:______________________________________________________________________
SHIP TO :_____________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
TEL :_________________________________
FAX :______________________________
EMAIL: __________________________________________________________________
VISA OR MASTERCARD # :_______________________________________ EXPIRY DATE: _____________
SIGNATURE:_____________________________________________________________________________
QUANTITY
PART NUMBER
DESCRIPTION
TAXES MAY APPLY
SHIPPING EXTRA
IF CONFIRMATION IS REQUIRED PLEASE INCLUDE A FAX NUMBER OR EMAIL ADDRESS
www.ultrachefgrills.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement