SDC25/26 Single Loop Controller User`s Manual

SDC25/26 Single Loop Controller User`s Manual
•
WARNING
(unit: mm)
Note that incorrect wiring of the SDC25/26 can damage the
SDC25/26 and lead to other hazards.
Check that the SDC25/26 has been correctly wired before turning
the power ON.
Before wiring, or removing/mounting the SDC25/26, be sure to
turn the power OFF.
Failure to do so might cause electric shock or faulty operation.
Do not touch electrically charged parts such as the power
terminals. Doing so might cause electric shock.
Do not disassemble the SDC25/26.
Doing so might cause electric shock or faulty operation.
ev2
ev3
sp
■ Unpacking
Check the following items when removing the SDC25/26 from its package:
Name
Part No.
Q'ty
Remarks
Mounting Bracket
81409654-001
2
User's Manual
CP-UM-5288E
1
This Manual
SAFETY PRECAUTIONS
Warnings are indicated when mishandling
WARNING this product might result in death or serious
injury to the user.
■ Location
Install the controller in the following locations:
· Common mode voltages for I/O except power supply and relay contact
output: The voltage to ground is 33Vr.m.s max., 46.7V peak max., and
70Vdc max.
· Not high or low temperature / humidity.
· Free from sulfide gas or corrosive gas.
· Less dust or soot.
· Appropriately processed locations to prevent direct sunlight, wind or rain.
· Less mechanical vibration and shock.
· Not close to the high voltage line, welding machine or electrical noise
generating source.
· The minimum 15 meters away from the high voltage ignition device for a
boiler.
· Less effect by the magnetic field.
· No flammable liquid or gas.
■ Mounting Procedure
· The mounting must be horizontal within 10 degrees tilted in back side
lowering or within 10 degrees tilted in back side rising.
· The mounting panel should be used with a thickness of less than 9 mm of
firm board.
■ External Dimensions
•
C25
(unit: mm)
5
Cautions are indicated when mishandling
this product might result in minor injury to
the user, or only physical damage to this
product.
48
enter
Handling Precautions
To fasten this controller onto the panel, tighten a mounting
bracket screws, and turn one more half turn when there is no
play between the bracket and panel. Excessively tightening the
screws may deform the controller case.
■ Panel Cutout Dimensions
(unit: mm)
SDC25
sp
out
man
mode
ev1
ev2
ev3
ot1
ot2
display
enter
para
1
● Connection of C25/26
Power supply
Stand-alone mounting
+0.5
0
(48xN–4)
92
44
+0.5
0
30 min.
Gang-mounting
+0.5
0
+0.5
0
1
AC power supply
100 to 240Vac
2
13
14
15
2
Event outputs
Relay
• C26
Gang-mounting
Stand-alone mounting
(96xN–4) +0.5
0
+0.5
0
92 +0.5
0
92
30 min.
Control outputs
1
DC power supply
24Vac/24Vdc
(non polar)
Relay
(independent
contact)
Current
Transformer
inputs
3
1
13
2
2
14
3
15
4
16
5
17
6
18
7
19
8
20
Inputs
9
21
7
8
9
10
22
11
23
12
24
3
4
5
6
1
COM
3
4
5
6
2
1
CT1
CT2
Handling Precautions
• When three or more units are gang-mounted horizontally, the
maximum allowable ambient temperature is 40°C.
+
C
A
Wiring
Be sure to provide a switch within operator reach for shutting OFF the main
power supply to the controller in the main supply wiring.
Also, in case of AC power supply models, the main supply wiring also requires
a time-lagged type (T) fuse (rated current: 0.5A, rated voltage: 250 V).
(IEC127)
The following table shows the meaning of the symbols in the terminal wiring
label on the controller side:
Symbols
Meaning
AC power supply
DC power supply
Caution, fear of electric shock
Caution
mA
Voltage
V
Voltage pulse
2+
Current/Voltage pulse
13
14
13
14
15
Voltage pulse
+
1–
+
–
Current
Current
+
–
2+
1
Current
Auxiliary output
+
–
4
3
2
1
COM
Current
18
19
Digital input
20
21
Communication
+
Current
13
14
15
+
–
DI
10
11
12
B
RTD
Relay
NC
13
14
10
11
12
–
Thermocouple
NO
16
17
PV inputs
Handling Precautions
• Before wiring the SDC25/26, verify the controller's model No.
and terminal Nos. written on the label on the side of the body.
Inspect all wiring once wiring work for the SCD25/26 has been
completed.
• Use M3 crimp-type terminal lugs for wiring to terminal.
• Provide a distance of at least 50cm between I/O lead wires or
communications lead wires and power lead wires. Also, do not
pass these lead wires through the same piping or wiring duct.
Terminal screw
M3
• Be careful not to allow any crimp-type terminal lugs to touch
adjacent terminals.
• Prepare a heater current conductor to send a heater current
through the current transformer.
Do not use a heater current that exceeds the specified
permissible current as this may damage the controller.
• The current transformer input cannot be used for phase
control.
• There is no isolation provided between control output 1 and
control output 2.
Install an isolator as required.
• Do not connect a terminating resistor to either end of the RS485 communications line.
Doing so may interfere with communication.
• Regarding a device or equipment which is connected to this
controller, use a model to which the basic insulation meeting
with the power supply voltage and the maximum operating
voltage of the I/O units is provided.
• The controller requires maximum 6 seconds to start up once
the power is turned ON.
The controller can be used once it has started up. However, it
is recommended to allow a warm-up time of at least 30
minutes to attain the specified accuracy.
• C25
65
Mounting bracket
(Accessory)
pv
96
CAUTION
display
para
30 min.
This manual explains the handling precautions, mounting, wiring, PV
range type, list of parameters and main specifications only. See the
separate "Installation & Configurations" manual listed below for the detail
handling procedures and the setting methods, etc. These manuals also
contain information on using various functions. Please read if necessary.
SDC25/26 Single Loop Controller User's Manual for
Installation & Configuration CP-SP-1149E
SLP-C35 Smart Loader Package for SDC15/25/26/35/36 Single Loop
Controller User's Manual CP-UM-5290E
mode
Mounting
108
2003 Yamatake Corporation ALL RIGHTS RESERVED
out
ot2
+0.5
0
Ensure that this User's Manual is handed over to the user before the
product is used.
Copying or duplicating this User's Manual in part or in whole is forbidden.
The information and specifications in this User's Manual are subject to
change without notice.
Considerable effort has been made to ensure that this User's Manual is
free from inaccuracies and omissions.
If you should find any inaccuracies or omissions, please contact
Yamatake Corporation.
In no event is Yamatake Corporation liable to anyone for any indirect,
special or consequential damages as a result of using this product.
108
ot1
92
REQUEST
pv
ev1
Use the SDC25/26 within the operating ranges recommended in
the specifications (temperature, humidity, voltage, vibration,
shock, mounting direction, atmosphere, etc.).
Failure to do so might cause fire or faulty operation.
Do not block ventilation holes.
Doing so might cause fire or faulty operation.
Wire the SDC25/26 properly according to predetermined
standards. Also wire the SDC25/26 using specified power leads
according to recognized installation methods.
Failure to do so might cause electric shock, fire or faulty operation.
Do not allow lead clippings, chips or water to enter the controller case.
Doing so might cause fire or faulty operation.
Firmly tighten the terminal screws at the torque listed in the
specifications. Insufficient tightening of terminal screws might
cause electric shock or fire.
Do not use unused terminals on the SDC25/26 as relay terminals.
Doing so might cause electric shock, fire or faulty operation.
We recommend attaching the terminal cover (sold separately)
after wiring the SDC25/26.
Failure to do so might cause electric shock.
Use the relays within the recommended service life.
Failure to do so might cause fire or faulty operation.
Use Yamatake Corporation's "SURGENON" if there is the risk of
power surges caused by lightning.
Doing so might cause fire or faulty operation.
Do not operate the keys with a propelling pencil or sharp-tipped
object. Doing so might cause faulty operation.
This product has been designed, developed and manufactured for
general-purpose application in machinery and equipment.
Accordingly, when used in applications outlined below, special care
should be taken to implement a fail-safe and/or redundant design
concept as well as a periodic maintenance program.
• Safety devices for plant worker protection
• Start/stop control devices for transportation and material
handling machines
• Aeronautical/aerospace machines
• Control devices for nuclear reactors
Never use this product in applications where human safety may be
put at risk.
Terminal screw
M3
SDC26
man
CAUTION
RESTRICTIONS ON USE
65
Mounting bracket
(Accessory)
92
Thank you for purchasing the SDC25/26.
Before operating this product described in this User's Manual, please
take note of the following points regarding safety.
Be sure to keep this manual nearby for handy reference.
5
96
96
SDC25/26
Single Loop Controller
User's Manual
for Installation
C26
30 min.
CP-UM-5288E
10
–
11
+ 12
DA
DB
SG
22
23 RS-485
24
● I/O isolation
Power supply
PV input
Current transfomer input 1
Current transfomer input 2
Loader communication
Digital input 1
Digital input 2
Digital input 3
Digital input 4
RS-485 communication
Control output 1
Control output 2
Auxiliary output
Internal circuit
Event output 1 (Note 1)
Event output 2 (Note 1)
Event output 3
Items surrounded by solid lines are insulated from other signals.
Availability of input or output is based on a model number.
Note 1 In case of independent contact, the part between the event output
1 and the event output 2 is isolated.
Part names and functions
Key operation and setting
The following shows the flow of key operation:
(1)
man
pv
Display when the power is turned ON.
pv
man
ev1
ev3
ev2
OFF
ot1
ev1
ev2
ev3
ot1
ot2
(3)
(4)
sp
(6) (5)
(9)
enter
OFF
(2)
out
mode
display
para
enter
ot2
mode
display
mode
(5)
sp
out
ot2
ev3
man
ot1
The mode indicators are lit sequentially form the left
during a period of 5 to 6 sec after the power has been
turned ON while both the upper display and lower
display are OFF. When all mode indicators have been
lit, the display is changed to the operation display.
SDC26
pv
ev1
ev2
(2)
sp
out
Cleaning :
When wiping out the SDC25/26, use the soft and dried cloth.
Parts replacement: Do not replace the parts.
Fuse replacement: When replacing the fuse for the power supply wires, make
sure that the replacement fuse complies with all applicable
safety standards.
Standard IEC127, Cutoff Speed Delayed operation type (T),
Rated Voltage 250V, Rated Current 0.5A
SDC26
SDC25
display
para
(6)
para
Keep the
key
pressed for 2 sec.
or longer.
enter
(9)
(10)
para
(10)
No key operation for
3 minutes or more.
display
enter
Press the
or Press the
or
mode
Bank selection display
Operation display
No key operation for
3 minutes or more.
display
Press the
< key.
key.
Optional unit Model No.:
QN212A (800 turns, hole diameter: 12mm)
Maintenance
or
mode
key.
(7)
<
<
C25
key.
Temperature unit setup
Press the
or
key.
Press the
Press the
Press the
para
Panel mounting type
key.
Press the
key.
Press the
or
R0
Relay contact
output NO
Relay contact
output NC
V0
Voltage pulse output
(for SSR drive)
–
VC
Voltage pulse output Current output
(for SSR drive)
VV
Voltage pulse output Voltage pulse output
(for SSR drive) (for SSR drive)
key.
Other banks (Operate
the [para], [ ] and [ ]
keys repeatedly.)
para
key.
or
or
<
Press the
key
key.
<
Other banks (Operate
the [para], [ ] and [ ]
keys repeatedly.)
Other display and
setup (Operate the
[display] key)
display
para
key.
para
Keep the
key
pressed for 2 seconds or longer.
The display and setup status shown above are examples for explanation. Therefore, some
displays or settings are not shown actually according to the model and/or setup contents.
C0
Current output
CC
Current output Current output
U
There are the standard type and special type in the data setup method.
Here, the method is explained in the standard type.
<
AC model (100 to 240Vac) 50/60Hz
D
Display the C0 1 on the upper display in the bank setup mode for the setup bank.
When the [enter] key is pressed, the numerical value on the lower display
will start to flash.
Move the digit or increase/decrease the numeric value by pressing the [<]
[ ] [ ] keys.
When the [enter] key is pressed at the desired numeric value, the flashing
will stop and the data will be set.
–
Universal
A
● Setting example of the PV range type
DC model (24Vac/24Vdc)
1
Event relay output: 3 points
2
Event relay output: 3 points,
Auxiliary output (current output)
(Note 2)
4
Event relay output: 2 points,
(independent contact)
(Note 2)
5
Event relay output: 2 points
(independent contact)
Auxiliary output (current output)
–
(Note 1)
1
Current transformer input: 2 points
Digital input: 4 points
Display the SP- 1 on the upper display in the bank setup mode of the setup
bank.
When the [enter] key is pressed, the numerical value on the lower display
will start to flash.
Move the digit or increase/decrease the numeric value by pressing the [<]
[ ] [ ] keys.
When the [enter] key is pressed at the desired numeric value, the flashing
will stop and the data will be set.
For details of the handling and setting methods, refer to the following user's
manual:
Single Loop Controller SDC25/26 User's Manual "Installation &
Configurations" CP-SP-1149E
(Note 1)
2
Current transformer input: 2 points
Digital input: 4 points
RS-485 communication
<
0
● Setting example of the SP1
Note 1. Current transformer is sold separately .
Note 2. Can not be selected for DC model.
Alarm code table
Failure name
PV input failure
(over range)
AL02
PV input failure
(under range)
AL03
CJ failure
PV input failure
AL1 1
AL70
AL95
CT input failure
(over-range)
(CT input 1 or 2,
or both)
A/D conversion
failure
Parameter failure
AL96
Adjustment data
failure
AL97
Parameter failure
(RAM area)
Adjustment data
failure
(RAM area)
ROM failure
AL98
AL99
Cause
Sensor line break, incorrect
wiring, incorrect PV range
type setting
Sensor line break, incorrect
wiring, incorrect PV range
type setting
Terminal temperature is
faulty (thermocouple).
Sensor line break, incorrect
wiring (RTD)
A current exceeding the upper
limit of the display range was
measured. The number of CT
turns or the number of CT
power wire loops is incorrectly
set, or wiring is incorrect.
Defective A/D converter
0
No additional treatment
D
Inspection certificate provided
T
Tropicalization treatment applied
K
Anti-sulfide treatment applied
B
Tropicalization treatment applied
and Inspection certificate provided
L
Anti-sulfide treatment applied and
Inspection certificate provided
Y
Complying with the traceability
certificate
0
IP65 inapplicable
Specifications
This table shows the alarm display and measures for the abnormal operation of
this controller.
Alarm code
AL0 1
Checking the ambient
temperature.
Checking wiring.
Use a CT with the correct
number of turns for the
display range, reset the
number of CT turns, reset
the number of CT power
wire loops, and/or check
the wiring.
Replace unit.
Re-start the system.
Reset data or replace
unit.
(AL95/97: setting data,
AL96/98: tuning data)
ROM (memory) error
Re-start the system.
Replace unit.
● PV input
Thermocouple:
Corrective action
Checking wiring or
reset PV range type.
• Power turned OFF during
fixing data
• Data corrupted due to noise,
etc.
• Power turned OFF during
fixing data
• Data corrupted due to noise, etc.
Data corrupted due to noise,
etc.
Data corrupted due to noise,etc.
Allowable measured
current:
70.0Aac (800 turns, 1 time)
Formula; Number of turns ÷ (16 x number of
power wire loops) x 1.4
0.0Aac
70.0Aac (800 turns, 1 time)
Formula; Number of turns ÷ (16 x number of
power wire loops) x 1.4
±5%FS
0.1Aac
Display accuracy:
Display resolution:
96 x 96 size model
<
Press the
key.
<
para
<
Press the
key
SP bank selection
Press the
<
display
50.0Aac (800 turns, 1 time)
Formula; Number of turns ÷ (16 x number of
power wire loops)
Display range lower limit:
Display range upper limit:
Specifications
Control output 1 Control output 2
MV display
Current measurement
upper limit:
48 x 96 size model
C26
T
<
Handling Precautions
C01
Sensor
Range
· The accuracy is ±0.3%FS±1 Set value
type
digit, and ±0.6%FS±1 digit for 81
0 to 10mV
The scaling and the decimal
a negative area of the
82 -10 to +10mV point position can be
thermocouple.
83
0 to 100mV
changed variably in a range
The accuracy varies
84
0 to 1V
of -1999 to +9999.
according to the range:
86
1 to 5V
The accuracy of the No.17
87
0 to 5V
(sensor type B) is ±4.0%FS 88
0 to 10V
for a range of 260°C or less, 89
0 to 20mA
±0.4%FS for 260 to 800°C. 90
4 to 20mA
The PV values under 20°C
are not shown.
The accuracy of the No.23 (sensor type PR40-20) is ±2.5%FS
for 0 to 300°C, and ±1.5%FS for 300 to 800°C, ±0.5%FS for 800
to 1900°C.
The accuracy of the No.26 (sensor type gold iron chromel) is
±1.5K.
The accuracy of the No.19 (sensor type PLII) in the range of 0 to
32˚F does not meet the indication accuracy.
· The ranges with a decimal point show figures under decimal point.
or
<
-300 to +900°F
-300 to +900°F
-300 to +400°F
-300 to +400°F
-150 to +500°F
-150 to +500°F
-150 to +400°F
-150 to +400°F
-150 to +300°F
-150 to +300°F
-50 to +400°F
-50 to +400°F
-50 to +200°F
-50 to +200°F
-60 to +100°F
-60 to +100°F
-40 to +140°F
-40 to +140°F
-10 to +140°F
-10 to +140°F
0 to 200°F
0 to 200°F
0 to 400°F
0 to 400°F
0 to 500°F
0 to 500°F
0 to 900°F
0 to 900°F
key.
out
<
-200.0 to +500.0°C
-200.0 to +500.0°C
-200.0 to +200.0°C
-200.0 to +200.0°C
-100.0 to +300.0°C
-100.0 to +300.0°C
-100.0 to +200.0°C
-100.0 to +200.0°C
-100.0 to +150.0°C
-100.0 to +150.0°C
-50.0 to +200.0°C
-50.0 to +200.0°C
-50.0 to +100.0°C
-50.0 to +100.0°C
-60.0 to +40.0°C
-60.0 to +40.0°C
-40.0 to +60.0°C
-40.0 to +60.0°C
-10.00 to +60.00°C
-10.00 to +60.00°C
0.0 to 100.0°C
0.0 to 100.0°C
0.0 to 200.0°C
0.0 to 200.0°C
0.0 to 300.0°C
0.0 to 300.0°C
0.0 to 500.0°C
0.0 to 500.0°C
Press the
or
<
-300 to +2200°F
0 to 2200°F
0 to 1500°F
0 to 1100°F
0 to 700°F
-300 to +700°F
-300 to +400°F
0 to 2200°F
0 to 1500°F
0 to 1100°F
-300 to +700°F
0 to 1500°F
0 to 1100°F
-300 to +700°F
0 to 3000°F
0 to 3000°F
0 to 3300°F
0 to 2300°F
0 to 2300°F
0 to 2400°F
0 to 4200°F
0 to 2300°F
0 to 3400°F
-300 to +700°F
-150 to +1500°F
0.0 to 360.0K
Range
PV range type setup
para
Press the
key.
Press the
Power Option 1 Option 2 Additions Additions
supply
1
2
<
-200 to +1200°C
0 to 1200°C
0.0 to 800.0°C
0.0 to 600.0°C
0.0 to 400.0°C
-200.0 to +400.0°C
-200.0 to +200.0°C
0 to 1200°C
0.0 to 800.0°C
0.0 to 600.0°C
-200.0 to +400.0°C
0.0 to 800.0°C
0.0 to 600.0°C
-200.0 to +400.0°C
0 to 1600°C
0 to 1600°C
0 to 1800°C
0 to 1300°C
0 to 1300°C
0 to 1400°C
0 to 2300°C
0 to 1300°C
0 to 1900°C
-200.0 to +400.0°C
-100.0 to +800.0°C
0.0K to 360.0K
C01 Sensor
Set value type
41 Pt100
42 JPt100
43 Pt100
44 JPt100
45 Pt100
46 JPt100
47 Pt100
48 JPt100
49 Pt100
50 JPt100
51 Pt100
52 JPt100
53 Pt100
54 JPt100
55 Pt100
56 JPt100
57 Pt100
58 JPt100
59 Pt100
60 JPt100
61 Pt100
62 JPt100
63 Pt100
64 JPt100
65 Pt100
66 JPt100
67 Pt100
68 JPt100
Mode bank selection
para
Press the
key.
<
Range
display
PV
input
<
PV range table
PV / SP display
Press the
key
<
<
Displays PV values (present temperature, etc.) or setup
items.
(2) Lower display: Displays SP values (set temperature, etc.) and other
parameter values. When the lower display shows the SP
value, the "sp" lamp lights up. When the display shows
the manipulated variable (MV), the "out" lamp lights up.
(3) Mode indicator man:
Lights when MANUAL (manual mode).
ev1 to ev3: Lights when event relays are ON.
ot1, ot2:
Lights when the control output is ON.
(4) Multi-status indicator:
In the combination of the lighting condition and the
lighting status as a group, the priority 3 groups can be set.
(5) [mode] key:
The operation which has been set beforehand can be done
by pushing the key for 1s or more.
(6) [display] key:
Used to change the display contents in the operation
display mode. Display is returned from bank setup display
to operation display.
(7) < , , key:
Used for incrementing numeric values and performing
arithmetic shift operations.
(8) [para] key:
Switches the display.
(9) [enter] keys:
Used to set the setup values at the start of change and
during the change.
(10) Loader connector: Connects to a personal computer by using a dedicated
cable supplied with the Smart Loader Package.
<
(1) Upper display:
C01 Sensor
Set value type
1
K
2
K
3
K
4
K
5
K
6
K
7
K
8
J
9
J
10
J
11
J
12
E
13
E
14
T
15
R
16
S
17
B
18
N
19 PLII
20 Wre5-26
21 Wre5-26
22 Ni-NiMo
23 PR40-20
24 DIN U
25 DIN L
26 Gold iron
chromel
Basic Mounting Control
model No.
output
sp
<
(8)
<
(7)
0.4Aac (800 turns, 1 time)
Formula; Number of turns ÷ (2000 x number of
power wire loops)
Model selection table
Bank setup display
pv
(8)
Current measurement
lower limit:
K,J,E,T,R,S,B,N (JIS C1602-1995)
PL II (Engelhard Industries Data (ITS90))
WRe5-26 (ASTM E988-96(Reapproved 2002))
Ni-NiMo (ASTM E1751-00)
PR40-20 (Johnson Matthey Data)
DIN U,DIN L (DIN 43710-1985)
Gold iron chromel (Hayashidenko Data)
Resistance temperature detector (RTD):
Pt100 (JIS C1604-1997)
JPt100 (JIS C1604-1989)
DC voltage:
0 to 10mV, -10 to +10mV, 0 to 100mV,
0 to 1V, 1 to 5V, 0 to 5V, 0 to 10V
DC current:
0 to 20mA, 4 to 20mA
Sampling cycle:
300ms
Indication accuracy:
±0.3%FS±1digit,
±0.6%FS±1digit for a negative area of the
thermocouple (at ambient temperature 23±2°C)
● Digital input
Input type:
Allowable ON contact
resistance:
Allowable OFF contact
resistance:
Allowable ON residual
voltage:
Terminal current (ON):
Dry contact or open collector
2
• Relay output
Contact rating:
NO side
250Vac/30Vdc, 3A (resistive load)
NC side
250Vac/30Vdc, 1A (resistive load)
Life:
NO side Min. 50,000 operations
NC side Min. 100,000 operations
Min. switching specifications: 5V, 100mA
Min. open time / close times:
250ms
• Voltage pulse output (for SSR drive)
Open circuit voltage:
19Vdc±15%
Internal resistance:
82Ω±0.5%
Allowable current:
Max. 24mAdc
Min OFF time / ON time:
1ms when the time proportional cycle time is
less than 10s.
250ms when the time proportional cycle time is
more than 10s.
• Current output
Output type:
0 to 20mAdc or 4 to 20mAdc
Allowable load resistance:
Max.600Ω
Output accuracy:
±0.1%FS (at ambient temperature 23±2°C)
±1%FS at 0 to 1mA
● Auxiliary output
Output type:
Allowable load resistance:
Output accuracy:
0 to 20mAdc or 4 to 20mAdc
Max.600Ω
±0.3%FS (at ambient temperature 23±2°C)
±1%FS at 0 to 1mA
● Event relay outputs (ev1 to ev3)
Output rating:
Life:
Min. switching specifications:
250Vac/30Vdc 2A (resistive load)
Min. 100,000 operations
5V, 10mA (reference value)
● RS-485 communication
Transmission line:
Transmission speed:
Communication protocol:
Terminating resistor:
3-wire system
4800, 9600, 19200, 38400bps
CPL and MODBUS conforming
Do not connect a terminating resistor.
● Environmental condition
• Operating conditions
Ambient temperature:
Ambient humidity:
Rated power supply voltage:
0 to 50°C (Gang-mounting: 0 to 40°C)
10 to 90%RH (non-condensing)
AC model 100 to 240Vac, 50/60Hz
DC model 24Vac 50/60Hz, 24Vdc
AC model 85 to 264Vac, 50/60±2Hz
DC model 21.6 to 26.4Vac, 50/60±2Hz
21.6 to 26.4Vdc
Power supply voltage range:
• Transport conditions
Ambient temperature:
Ambient humidity:
-20 to +70°C
10 to 95%RH (non-condensing)
● Other specifications
Power consumption:
Non-detected failure time:
Altitude:
Mass:
Terminal screw tightening torque:
Applicable standards:
Over-voltage category:
Allowable pollution degree:
Max.250Ω
Max. 12VA for AC model
Max. 12VA for DC model at 24Vac
Max. 8W for DC model at 24Vdc
Max. 20ms (AC model)
No power failure allowed (DC model)
2000m or less
C25 Approx.250g (with mounting bracket)
C26 Approx.300g (with mounting bracket)
0.4 to 0.6 N·m Max.
EN61010-1, EN61326
Category II (IEC60364-4-443, IEC60664-1)
Pollution degree 2
Accessories and optional parts
Min.100kΩ
Max.1.0V
Approx.7.5mA (in case of short circuit).
Approx.5.0mA (in case of contact resistance 250Ω)
Minimum hold time:
600ms or more
● Current transformer input
Number of input points:
Input object:
● Control output
2 points
Current transformer with 100 to 4,000 turns
(availability is by 100-turn units)
Optional unit Model No.:
QN206A (800 turns, hole diameter: 5.8 mm)
Name
Mounting bracket
Current transformer
Hard cover
Soft cover
Terminal cover
Model No.
81409654-001(Accessory)
QN206A(5.8mm hole dia.)
QN212A(12mm hole dia.)
81446915-001(for C25)
81446916-001(for C26)
81441121-001(for C25)
81441122-001(for C26)
81446912-001(for C25)
81446913-001(for C26)
0: Display in basic/standard/high function,
1: Display in standard/high function,
2: Display in high function.
Initial value may vary depending on model No.
[List of Operation Displays]
■ Operation Displays
Display
Upper display: PV
Lower display: SP
LSP 1
(Display example)
Lower display:
LSP
Upper display: PV
Lower display: MV
HEAt
COOL
Upper display: PV
At 1
(Display example)
Ct 1
Ct2
E1
E 1. Sb
t 1. -(Display example)
E2
E2. Sb
Item
Display
Initial
value
0
User
level
0
LSP No. (1st digit: 1 to LSP system group (C30 Max. 4)
Value at the
right end digit)
1
0
MV (Manipulated
Variable)
—
SP (Target value)
Heat MV
(Manipulated
Variable)
Cool MV
(Manipulated
Variable)
AT progress
display (1st digit
= Numeric value
at right end digit)
CT (Current
transformer)
current value 1
CT (Current
transformer)
current value 2
Internal event 1
main setting
Internal event 1
sub-setting
Timer remaining
time 1
Internal event 2
main setting
Internal event 2
sub-setting
t2. -(Display example)
Timer remaining
time 2
E3
E3. Sb
Internal event 3
main setting
Internal event 3
sub-setting
t3. -(Display example)
Timer remaining
time 3
Contents
SP low limit (C07) to SP high limit (C08)
–10.0 to +110.0%
Setting is disabled in AUTO mode.
(Numeric value does not flash.)
Setting is enabled in MANUAL mode.
(Numeric value flashes.)
Setting is disabled
–10.0 to +110.0%
—
—
0
0
0
A--M
r--r
Setting is disabled.
Except for 0: During execution of AT
(Value is decreased.)
0: Completion of AT
Setting is disabled.
—
0
—
0
Setting is disabled.
—
0
Setting range is different depending on the internal
event operation type.
–1999 to +9999U: Except below.
0 to 9999U: Setting value is an absolute value.
–199.9 to +999.9%: For MV.
Setting is disabled.
Upper display: The distinction by ON delay or OFF
delay is displayed at the side location of [t1.].
Lower display: Displayed by the unit (either one of
0.1s, s, or min) based on the internal event 1 delay
time unit (E1. the 3rd digit of C3).
Setting range is different depending on the internal
event operation type.
–1999 to +9999U: Except below.
0 to 9999U: Setting value is an absolute value.
–199.9 to +999.9%: For MV.
Setting is disabled.
Upper display: The distinction by ON delay or OFF
delay is displayed at the side location of [t2.].
Lower display: Displayed by the unit (either one of
0.1s, s, or min) based on the internal event 2 delay
time unit (E2. the 3rd digit of C3).
Setting range is different depending on the internal
event operation type.
–1999 to +9999U: Except below.
0 to 9999U: Setting value is an absolute value.
–199.9 to +999.9%: For MV.
Setting is disabled.
Upper display: The distinction by ON delay or OFF
delay is displayed at the side location of [t3.].
Lower display: Displayed by the unit (either one of
0.1s, s, or min) based on the internal event 3 delay
time unit(E3. the 3rd digit of C3).
At
do Lt
C. dI 1
Item
AUTO/MANUAL
mode selection
RUN/READY
mode selection
AT Stop/Start
selection
Release all DO
latches
Communication
DI 1
0
0
0
0
—
0
0
0
0
0
—
0
SP- 1 to
SP-4
Contents
AUTO : AUTO mode
MAN : MANUAL mode
RUN : RUN mode
RDY : READY mode
At. OF : AT Stop
At. ON : AT Start
Lt. ON : Latch continue
Lt. OF : Latch release
dI. OF : OFF
dI. On : ON
PId. 1 to
PId. 4
Item
SP of LSP1 group
to SP of LSP4
group
PID group No
(for LSP1 to 4)
Item
E 1 to
E5
E 1. Sb to
E5. Sb
E 1. Hy to
E5. Hy
Internal event 1 to
5, main setting
Internal event 1 to
5, sub-setting
Internal event 1 to
5, hysteresis
E 1. On to
E5. On
E 1. OF to
E5. OF
Internal event 1 to
5, ON delay
Internal event 1 to
5, OFF delay
Contents
–1999 to +9999
The decimal point position varies by meeting the
internal event operation type.
0 to 9999 for some operation type.
0 to 9999
The decimal point position varies by meeting the
internal event operation type.
0.0 to 999.9
(For the delay time unit 0.1s)
0 to 9999
(Except for the delay time unit 0.1s)
Initial
value
0
User
level
0
0
0
5
0
0
2
0
2
C 02
C 03
C 04
C 05
Contents
SP low limit (C07) to SP high limit (C08)
1 to 4
■ PID bank
Bank selection: PId
Display
P- 1 to
P-4
I- 1 to
I-4
d- 1 to
d-4
rE- 1 to
rE-4
OL- 1 to
OL-4
OH- 1 to
OH-4
P- 1 C to
P-4 C
I- 1 C to
I-4 C
d- 1 C to
d-4 C
OL. 1 C to
OL.4 C
0
0
0
0
—
0
OH. 1 C to
OH.4 C
Item
Proportional band
(PID1 to 4 group)
Integration time
(PID1 to 4 group)
Derivative time
(PID1 to 4 group)
Manual reset
(PID1 to 4 group)
MV low limit
(PID1 to 4 group)
MV high limit
(PID1 to 4 group)
Cool-side
proportional band
(PID1 to 4 group)
Cool-side
integration time
(PID1 to 4 group)
Cool-side
derivative time
(PID1 to 4 group)
Cool-side MV low
limit (PID1 to 4
group)
Cool-side MV high
limit (PID1 to 4
group)
Contents
0.1 to 999.9%
0
0
–10.0 to +110.0%
0.0
1
–10.0 to +110.0%
C 14
C 15
C 16
C 17
100.0
1
C 18
5.0
0
C 19
0 to 9999s or 0.0 to 999.9s
(0: No integral control action)
120
0
0 to 9999s or 0.0 to 999.9s
(0: No derivative control action)
30
0
–10.0 to +110.0%
0.0
1
–10.0 to +110.0%
100.0
1
C 20
C21
C 24
C 26
C 27
C 28
C 29
CtrL
Control method
At. OL
At. OH
dIFF
OFFS
MV low limit at AT
MV high limit at AT
ON/OFF control differential
ON/OFF control operating
point offset
PV filter
PV ratio
PV bias
Time proportional cycle unit 1
FL
rA
bI
CyU
C 30
Item
Cy
Time proportional cycle1
AT Stop
0
CyU2
Time proportional cycle unit 2
Latch
continue
OFF
0
1
C 07
C 08
C 09
0.1 to 999.9%
0
1
0
30
RUN
User
level
0
120
50.0
User
level
0
Initial
value
0
User
level
0
0 to 9999s or 0.0 to 999.9s
(0: No integral control action)
0 to 9999s or 0.0 to 999.9s
(0: No derivative control action)
–10.0 to +110.0%
Initial
value
AUTO
0
Initial
value
5.0
■ Parameter bank
Bank selection: PArA
Display
■ SP bank
Bank selection: SP
Display
C01
C 06
[List of Parameter Setting Displays]
■ Mode bank
Bank selection: MOdE
Display
■ Event bank
Bank selection: Ev
Display
Cy2
Time proportional cycle 2
tP. ty
Time proportional operation
type
SPU
SPd
SP ramp-up
SP ramp-down
Contents
0: ON/OFF control
1: PID fixed
–10.0 to +110.0%
–10.0 to +110.0%
0 to 9999U
–1999 to 9999U
0.0 to 120.0s
0.001 to 9.999
–1999 to +9999U
0: 1s unit
1: 0.5s fixed (Cycle time is disabled.)
2: 0.2s fixed (Cycle time is disabled.)
3: 0.1s fixed (Cycle time is disabled.)
5 to 120s (*1)
1 to 120s (*2)
0: 1s unit
1: 0.5s fixed (Cycle time is disabled.)
2: 0.2s fixed (Cycle time is disabled.)
3: 0.1s fixed (Cycle time is disabled.)
5 to 120s (*1)
1 to 120s (*2)
0: Controllability aiming type
1: Actuator life aiming type
(Only one ON/OFF operation within time
proportional cycle time)
0.0 to 999.9U (0.0: No ramp)
C 32
Initial
value
0 or 1
User
level
0
0.0
100.0
5
0
0
0
0
2
C 37
0.0
1.000
0
0
0
1
0
2
C 38
10 or 2
0
C 42
0
2
10 or 2
0
0 or 1
2
0.0
0.0
2
2
C 36
C 39
C 40
C41
C 43
C 44
*1 When the output includes the relay ouput.
*2 When the output does not include the relay output.
C 45
C 46
■ Extension tuning bank
Bank selection: Et
Display
At. ty
JF. bd
SP. LG
At-P
At-I
At-d
Ctr. A
JF. Ov
Item
AT type
Just-FiTTER setting band
SP lag constant
AT proportional band tuning
factor
AT integration time tuning
factor
AT derivative time tuning
factor
Control algorithm
Just-FiTTER overshoot
suppression factor
C 47
Contents
0: Normal (Standard control characteristcis)
1: Immediate response (Control
characteristcis immediately responding
to the external disturbance.)
2: Stable (Control characteristics with less
up/down function of PV)
0.00 to 10.00
0.0 to 999.9
0.00 to 99.99
Initial
value
1
C 48
User
level
0
C 49
C 50
C51
0.30
0.0
1.00
2
2
2
C 52
0.00 to 99.99
1.00
2
C 54
0.00 to 99.99
1.00
2
C 55
0
1
C 56
0
1
C 64
0: PID (conventional PID)
1: RationaLOOP (high performance type)
0 to 100
CP-UM-5288E
[List of Setup Setting Displays]
■ Setup bank
Bank selection: StUP
User level details
SDC25/26 List of Parameters
C 53
3
Item
PV input range
type
Contents
Initial
value
88
Thermocouple: 1 to 26
RTD: 41 to 68
DC current/voltage: 81 to 84, 86 to 90
Temperature unit 0: Centigrade (°C)
0
1: Fahrenheit (°F)
Cold junction
0: Cold junction compensation is performed. (Internal)
0
compensation
1: Cold junction compensation is not performed.
(T/C)
(External)
Decimal point
0: No decimal point
0
position
1: One digit after decimal point
2: Two digits after decimal point
3: Three digits after decimal point
(Select ‘0’ or ‘1’ for the thermocouple/RTD range
with decimal point)
PV range low limit When the PV input range type is thermocouple or
0
RTD, the setting is disabled although range low limit is
displayed. –1999 to +9999U when the PV input range
type is DC voltage/current.
PV range high limit When the PV input range type is thermocouple or
1000
RTD, the setting is disabled although range high limit
is displayed. –1999 to +9999U when the PV input
range type is DC voltage/current.
SP low limit
PV input range low limit to PV input range high limit
0
SP high limit
1000
Square root
0.0 to 100.0%
0.0
extraction dropout (0.0: No square root extraction)
Control action
0: Heat control (reverse action)
0
(direct/reverse)
1: Cool control (direct action)
Selection of MV
0: Control operation is continued.
0
at PV alarm
1: MV at PV alarm occurrence is outputted.
occurrence
MV at PV alarm
–10.0 to +110.0%
0.0
occurrence
MV at READY (at –10.0 to +110.0%
0.0
heat-side for
heat/cool control)
MV at READY (at –10.0 to +110.0%
0.0
cool-side)
Operation at
0: Bump-less
0
MANUAL change 1: Preset
Preset MANUAL
–10.0 to +110.0%
0.0 or
value
(Used even at MANUAL mode when power is ON.)
50.0
PID operation
0: Automatic
0
initialization
1: Not initialized
function selection 2: Initialized (when SP value different from current
value is inputted.)
Zone PID action
0: Disabled
0
selection
1: Selection by SP
2: Selection by PV
Heat/cool control 0: Disabled.
0
selection
1: Enabled.
Heal/cool selection 0: Normal
0
1: Energy saving
Dead zone
–100.0 to +100.0%
0.0
Heal/cool control
–10.0 to +110.0%
50.0
selection point
LSP setting
1 to 4
1
system
SP ramp unit
0: 0.1U/s
1
1: 0.1U/min
2: 0.1U/h
CT1 operation
0: Heater burnout detection
0
type
1: Current value measurement
CT1 output
0: Control output 1
0
1: Control output 2
2: Event output 1
3: Event output 2
4: Event output 3
CT1 measurement 30 to 300ms
30
wait time
CT2 operation
Same as CT1.
0
type
CT2 output
Same as CT1.
0
CT2 measurement Same as CT1.
30
wait time
Control output 1
Current output:
1
range
1: 4 to 2mA
2: 0 to 20mA
Control output 1
0: MV
0
type
1: Heat MV (for heat/cool control)
2: Cool MV (for heat/cool control)
3: PV
4: PV before ratio bias filter
5: SP
6: Deviation (PV-SP)
7: CT1 current value
8: CT2 current value
9: MFB (Invalid on SDC25/26)
10: SP+MV
11: PV+MV
Control output 1
–1999 to +9999
0.0
scaling low limit
(The decimal point position and unit may vary
Control output 1
depending on the control output 1 type.)
100.0
scaling high limit
Control output 1
0 to 9999
200
MV scalable bandwidth (Available when control output 1 type is 10 or 11.)
Control output 2
Same as control output 1.
1
range
Control output 2
3
type
Control output 2
–1999 to +9999
0
scaling low limit
(The decimal point position and unit may vary
Control output 2
depending on the control output 2 type.)
1000
scaling high limit
Control output 2
0 to 9999
200
MV scalable bandwidth (Available when control output 2 type is 10 or 11.)
Auxiliary output
Same as control output 1
1
range
Auxiliary output
3
type
Auxiliary output
–1999 to +9999
0
scaling low limit
(The decimal point position and unit may vary
Auxiliary output
depending on the auxiliary output type.)
1000
scaling high limit
Auxiliary output
0 to 9999
200
MV scalable bandwidth (Available when auxiliary output type is 10 or 11.)
Communication
0: CPL
0
type
1: MODBUS ASCII format
2: MODBUS RTU format
User
level
0
Display
Item
C 65
Station address
C 66
Transmission
speed
C 67
Data format (data
length)
Data format
(parity)
0
2
0
C 68
C 69
C 70
0
C71
0
C 72
1
1
2
0
C 73
2
2
1
1
1
1
2
C 74
2
0
1
C 75
0
2
0
2
0
C 76
0
0
0
C 77
0
0
0
0
C 78
C 79
0
0
0
0
0
0
0
0
0
0
0
0
0
0
C 80
Data format (stop
bits)
Communication
minimum response
time
Key operation
mode/type
Mode key
function
Contents
0 to 127
(Communication is disabled when "0" is set.)
0: 4800bps
1: 9600bps
2: 19200bps
3: 38400bps
0: 7bit
1: 8bit
0: Even parity
1: Odd parity
2: No parity
0: 1bit
1: 2bits
1 to 250ms
0: Standard type
1: Special type
0: Invalid
1: AUTO/MANUAL selection
2: RUN/READY selection
3: AT Stop/Start
4: LSP group selection
5: Release of all DO latches
6: Invalid
7: Communication DI1 selection
8: Invalid
Mode display
Whether the mode bank setup display is enabled or
setup
disabled is determined by the sum of the following
weighting:
Bit 0: AUTO/MANUAL display
0: Disabled, +1: Enabled
Bit 1: RUN/READY display
0: Disabled, +2: Enabled
Bit 2: LSP/RSP display
0: Disabled, +4: Enabled
Bit 3: AT stop/start display
0: Disabled, +8: Enabled
Bit 4: DO latch release
0: Disabled, +16: Enabled
Bit 5: Communication DI1 ON/OFF display
0: Disabled, +32: Enabled
Other invalid setup: 0, +64, +128
PV/SP value
Whether the basic display is enabled or
display setup
disabled is determined by the sum of the
following weighting:
Bit 0: PV display
0: Disabled, +1: Enabled
Bit 1: SP display
0: Disabled, +2: Enabled
Bit 2: LSP group No. display
0: Disabled, +4: Enabled
Other invalid setup: 0, +8
MV display setup Whether the basic display is enabled or disabled is
determined by the sum of the following weighting:
Bit 0: MV display
0: Disabled, +1: Enabled
Bit 1: Heat MV/cool MV display
0: Disabled, +2: Enabled
Bit 2: MFB display
0: Disabled, +4: Enabled
Bit 3: AT progress display
0: Disabled, +8: Enabled
Event setting value 0: In the operation display mode, the internal event
display setup
setting value is not displayed.
1: In the operation display mode, the internal event 1
setting value is displayed.
2: In the operation display mode, the internal event 1
to 2 setting value is displayed.
3: In the operation display mode, the internal event 1
to 3 setting value is displayed.
Event remaining
0: In the operation display mode, the ON/OFF delay
time display setup
remaining time of the internal event is not
displayed.
1: In the operation display mode, the ON/OFF delay
remaining time of the internal event 1 is displayed.
2: In the operation display mode, the ON/OFF delay
remaining time of the internal event 1 to 2 is
displayed.
3: In the operation display mode, the ON/OFF delay
remaining time of the internal event 1 to 3 is
displayed.
CT input current
0: In the operation display mode, the CT current
value display
value is not displayed.
setup
1: In the operation display mode, the CT1 current
value is displayed.
2: In the operation display mode, the CT1 to 2
current value is displayed.
User level
0: Basic configuration
1: Standard configuration
2: High function configuration
LED monitor
0: Disabled
1: Flashing at RS-485 communication signal
transmission
2: Flashing at RS-485 communication signal
receiving
3: OR (logical sum) of all DI status
4: Flashing at READY
Initial
value
0
User
level
0
2
0
1
0
0
0
0
0
3
2
0
2
1
0
255
1
15
1
15
1
0
1
0
1
0
1
1
0
0
2
(continued on back page)
■ Event assignment bank
Bank selection: EvCF
Display
C81
C 82
C 83
C 84
C 85
C 86
C 87
C 88
C 89
C 90
C91
C 92
C 93
Item
Contents
MS indicating
0: Normally open (Normally OFF=0)
lamp ON condition 1: Normally close (Normally ON=1)
(1st priority)
2 to 6: Internal event 1 to 5
7 to 9: Internal event 6 to 8 (Invalid in this unit)
10 to 13: Undefined
14: MV1 (ON/OFF, time proportional 1, heat-side,
OPEN-side output)
15: MV2 (time proportional 2, cool-side, CLOSE-side
output)
16 to 17: Undefined
18 to 21: DI1 to DI4
22 to 25: Undefined
26 to 30: Internal contact 1 to 5
31 to 33: Undefined
34 to 37: Communication DI1 to DI4
38: MANUAL
39: READY
40: RSP
41: AT
42: During ramp
43: Undefined
44: Alarm
45: PV alarm
46: Undefined
47: Mode key function selection status
48: Event output 1 status
49: Control output 1 status
MS indicating
0: Lit
lamp ON status
1: Slow flashing
(1st priority)
2: 2 times flashing
3: Fast flashing
4: Left → Right
5: Right → Left
6: Right to left going and returning
7: Deviation OK
8: Deviation graph
9: MV graph
10: Heat-side MV graph
11: Cool-side MV graph
12: MFB graph
13: DI monitor
14: Internal contact monitor
15: Internal event monitor
MS indicating
Same as MS indicating lamp ON condition
lamp ON condition (1st priority)
(2nd priority)
MS indicating
Same as MS indicating lamp ON status (1st priority)
lamp ON status
(2nd priority)
MS indicating
Same as MS indicating lamp ON condition
lamp ON condition (1st priority)
(3rd priority)
MS indicating
Same as MS indicating lamp ON status (1st priority)
lamp ON status
(3rd priority)
MS indicating
0 to 9999U
lamp deviation
range
Special function
0 to 15
(0 at power supply ON.)
Zener barrier
Rewriting by adjustment is enabled.
adjustment
Numerical value inputting manually is disabled
CT1 number of
0: 800 turns
winding
1 to 40: Setting value multiplied by one hundred
becomes number of winding.
CT1 number of
0: 1time
power wire loops 1 to 6: number of times
CT2 number of
0: 800 turns
winding
1 to 40: Setting value multiplied by one hundred
becomes number of winding.
CT2 number of
0: 1time
power wire loops 1 to 6: number of times
Initial
value
39
1
User
level
2
Display
E 1. C 1 to
E5. C 1
2
E 1. C2 to
E5. C2
44
6
2
2
E 1. C3 to
E5. C3
1
Item
Operation type of
internal event 1 to
5
Configuration 1
Operation type
2
9
2
5
2
0
2
0.00
2
8
2
1
2
8
2
1
2
Internal event 1 to
5
Configuration 2
1st digit:
Direct /Reverse
2nd digit:
Stand-by
3rd digit:
EVENT state at
READY
4th digit:
Undefined
Internal event 1 to
5
Configuration 3
1st digit:
Alarm OR
2nd digit:
Special OFF
3rd digit:
Delay time unit
4th digit:
Undefined
Contents
0: No event
1: PV high limit
2: PV low limit
3: PV high/low limit
4: Deviation high limit
5: Deviation low limit
6: Deviation high/low limit
7: Deviation high limit (Final SP reference)
8: Deviation low limit (Final SP reference)
9: Deviation high/low limit (Final SP reference)
10: SP high limit
11: SP low limit
12: SP high/low limit
13: MV high limit
14: MV low limit
15: MV high/low limit
16: CT1 heater burnout/over-current
17: CT1 heater short-circuit
18: CT2 heater burnout/over-current
19: CT2 heater short-circuit
20: Loop diagnosis 1
21: Loop diagnosis 2
22: Loop diagnosis 3
23: Alarm (status)
24: READY (status)
25: MANUAL (status)
26: Invalid
27: During AT execution (status)
28: During SP ramp (status)
29: Control direct action (status)
30: Invalid
31: Invalid
32: Timer (status)
33: MFB high/low limit
Digits are called as 1st digit, 2nd digit, 3rd digit and
4th digit from the right end digit.
0: Direct
1: Reverse
0: None
1: Standby
2: Standby + Standby at SP change
0: Continue
1: Forced OFF
0
Initial
value
0
Display
User
level
0
dI 1. 3 to
dI5. 3
dI 1. 4 to
dI5. 4
dI 1. 5 to
dI5. 5
dI 1. 6 to
dI5. 6
dI 1. 7 to
dI5. 7
0000
0
0
0
0
dI 1. 8 to
dI5. 8
dI 1. 9 to
dI5. 9
0
Digits are called as 1st digit, 2nd digit, 3rd digit and
4th digit from the right end digit.
0: No event
1: Alarm direct + OR operation
2: Alarm direct + AND operation
3: Alarm reverse + OR operation
4: Alarm reverse + AND operation
0: As normal execution
1: Event OFF at the event setting value (main)=0
0: 0.1s
1: 1s
2: 1min
0
0000
2
0
Item
dI 1. 1 to
dI5. 1
dI 1. 2 to
dI5. 2
Item
Internal contact 1
to 5
Operation type
Internal contact 1
to 5
Input bit operation
Contents
0: No function
1: LSP group selection (0/+1)
2: LSP group selection (0/+2)
3: LSP group selection (0/+4)
4: PID group selection (0/+1)
5: PID group selection (0/+2)
6: PID group selection (0/+4)
7: RUN/READY selection
8: AUTO/MANUAL selection
9: Invalid
10: AT Stop/Start
11: Invalid
12: Control action direct/reverse selection (As per
setting/opposite operation of setting)
13: SP ramp Enabled/Disabled
14: PV Hold (No-hold/Hold)
15: PV maximum value hold (No-hold/Hold)
16: PV minimum value hold (No-hold/Hold)
17: Timer Stop/Start
18: Release of all DO latches (Continue/Release)
19: Invalid
20: Invalid
0: Disabled. (Input of default)
1: Function 1 ((A and B) or (C and D))
2: Function 2 ((A or B) and (C or D))
3: Function 3 (A or B or C or D)
4: Function 4 (A and B and C and D)
Initial
value
2 to 5
or 0
0
User
level
2
Display
Ot 1. 6 to
Ot2. 6
Ev 1. 6 to
Ev3. 6
2
0
2
0
2
Ot 1. 7
Ot2. 7
Ev 1. 7
Ev3. 7
Ot 1. 8
Ot2. 8
Ev 1. 8
Ev3. 8
to
to
to
to
Display
2
UF-3
0
UF-4
0
UF-5
0
UF-6
UF-7
0
UF-8
0
2
0
2
0
Display
0
Ot 1. 1 to
Ot2. 1
Ev 1. 1 to
Ev3. 1
Item
Control output 1
to 2, event output
1 to 3
Operation type
Initial
value
0
Ot 1. 2 to
Ot2. 2
Ev 1. 2 to
Ev3. 2
User
level
0
Ot 1. 3 to
Ot2. 3
Ev 1. 3 to
Ev3. 3
Ot 1. 4 to
Ot2. 4
Ev 1. 4 to
Ev3. 4
0
Control output 1
to 2, event output
1 to 3
Output assignment A
Control output 1
to 2, event output
1 to 3
Output assignment B
Control output 1
to 2, event output
1 to 3
Output assignment C
2
Ot 1. 5 to
Ot2. 5
Ev 1. 5 to
Ev3. 5
Control output 1
to 2, event output
1 to 3
Output assignment D
Contents
0: Input of default
1: MV1 (ON/OFF control output, time proportional
output, heat-side proportional output of heat/cool
control)
2: MV2 (cool-side proportional output of heat/cool
control)
3: Function 1 ((A and B) or (C and D))
4: Function 2 ((A or B) and (C or D))
5: Function 3 (A or B or C or D)
6: Function 4 (A and B and C and D)
0: Normally open (OFF, 0)
1: Normally close (ON, 1)
2: Internal event 1
3: Internal event 2
4: Internal event 3
5: Internal event 4
6: Internal event 5
7 to 13: Undefined
14: MV1
15: MV2
16 to 17: Undefined
18: DI1
19: DI2
20: DI3
21: DI4
22 to 25: Undefined
26: Internal contact 1
27: Internal contact 2
28: Internal contact 3
29: Internal contact 4
30: Internal contact 5
31 to 33: Undefined
34: Communication DI1
35: Communication DI2
36: Communication DI3
37: Communication DI4
38: MANUAL mode
39: READY mode
40: Undefined
41: During AT execution
42: During SP ramp
43: Undefined
44: Alarm is enabled.
45: PV alarm is enabled.
46: Undefined
47: Mode key function selection status
48: Event output 1 status
49: Control output 1 status
Initial
value
0000
User
level
2
0
0
0
0
0
2
0
2
Contents
Initial
value
User
level
This is the display in upper display. The setup
exception is as follows:
---- : Yet to be registered.
P-- : Proportional band of the PID group in use
I-- :
Integration time of the PID group in use
d-- : Derivative time of the PID group in use
rE-- : Manual reset of the PID group in use
OL-- : MV low limit of the PID group in use
OH-- : MV high limit of the PID group in use
P--C : Cool-side proportional band of the PID
group in use
I--C : Cool-side integration time of the PID group
in use
d--C : Cool-side derivative time of the PID group
in use
Ol.-C : Cool-side MV low limit of the PID group in
use
Oh.-C : Cool-side of MV high limit of the PID group
in use
----
1
----
1
----
1
----
1
----
1
----
1
----
1
----
1
Initial
value
0
User
level
0
0: Direct
1: Reverse
0: Direct
1: Reverse
0: Disabled
1: Enabled (Latch at ON)
2: Enabled (Latch at OFF, except at the time of
initialization after power ON)
■ Lock bank
Bank selection: LOC
Display
0
Contents
Digits are called as 1st digit, 2nd digit, 3rd digit and
4th digit from the right end digit.
Item
User function
definition 1
User function
definition 2
User function
definition 3
User function
definition 4
User function
definition 5
User function
definition 6
User function
definition 7
User function
definition 8
UF-2
0000
Item
Control output 1
to 2, event output
1 to 2
Polarity A to D
1st digit: Polarity A
2nd digit: Polarity B
3rd digit: Polarity C
4th digit: Polarity D
Control output 1
to 2, event output
1 to 3
Polarity
Control output 1
to 2, event output
1 to 3
Latch
■ User function bank
Bank selection: UF
UF- 1
■ DO assignment bank
Bank selection: dO
■ DI assignment bank
Bank selection: dI
Display
Contents
Internal contact
0: Normally open (OFF, 0)
1 to 5
1: Normally close (ON, 1)
Input assignment A 2: DI1
3: DI2
4: DI3
5: DI4
6 to 9: Undefined
Internal contact
10: Internal event 1
1 to 5
11: Internal event 2
Input assignment B 12: Internal event 3
13: Internal event 4
14: Internal event 5
15 to 17: Undefined
18: Communication DI1
Internal contact
19: Communication DI2
1 to 5
20: Communication DI3
Input assignment C 21: Communication DI4
22: MANUAL mode
23: READY mode
24: Undefined
25: During AT execution
26: During SP ramp
Internal contact
27: Undefined
1 to 5
28: Alarm is enabled.
Input assignment D 29: PV alarm is enabled.
30: Undefined
31: Mode key function selection status
32: Event output 1 status
33: Control output 1 status
Internal contact
Digits are called as 1st digit, 2nd digit, 3rd digit and
1 to 5
4th digit from the right end digit.
Polarity A to D
1st digit: Polarity A 0: Direct
(Polarity of input
1: Reverse
assignment A)
2nd digit: Polarity B
(Polarity of input
assignment B)
3rd digit: Polarity C
(Polarity of input
assignment C)
4th digit: Polarity D
(Polarity of input
assignment D)
Internal contact
0: Direct
1 to 5 Polarity
1: Reverse
Internal contact
0: Every internal event
1 to 5
1 to 5: Internal event number
Internal event
No.assignment
Initial
value
0
14 to 15
or
2 to 4
User
level
2
2
Item
LOC
Key lock
C. LOC
L. LOC
Communication
lock
Loader lock
PASS
Password display
PS 1A
PS2A
PS 1b
PS2b
Password 1A
Password 2A
Password 1B
Password 2B
Contents
0: All settings are enabled.
1: Mode, event, operation display, SP, UF, lock,
manual MV, and mode key can be set.
2: Operation display, SP, UF, lock, manual MV, and
mode key can be set.
3: UF, lock, manual MV, and mode key can be set.
0: RS-485 communication read/write is enabled.
1: RS-485 communication read/write is disabled.
0: Loader communication read/write is enabled.
1: Loader communication read/write is disabled.
0 to 15
5: Password 1A to 2B display
0000 to FFFF (hexadecimal value)
0000 to FFFF (hexadecimal value)
0000 to FFFF (hexadecimal value)
0000 to FFFF (hexadecimal value)
0
2
0
2
0
0
0000
0000
0000
0000
0
0
0
0
Initial
value
-------------
User
level
2
2
2
2
----
2
----
2
----
2
----
2
■ Instrument information bank
Bank selection: Id
Display
0
2
Id0 1
Id02
Id03
Id04
Id05
Id06
0
2
Id07
Id08
0
Item
ROM ID
ROM version 1
ROM version 2
SLP support
Information
EST support
version
Manufacturing
date code (year)
Manufacturing
date code (month,
day)
Serial No.
Contents
1 fixed
XX. XX (2 digits after decimal point)
XX. XX (2 digits after decimal point)
Year - 2000.
Ex.: “3” means the year 2003.
Month + Day ÷ 100.
Ex.: “12.01” means the 1st day of December
2
Specifications are subject to change without notice.
Advanced Automation Company
1-12-2 Kawana, Fujisawa
Kanagawa 251-8522 Japan
Printed in Japan.
1st Edition: Issued in Oct. 2003 (A)
9th Edition: Issued in Nov. 2006 (W)
URL: http://www.azbil.com
Printed on recycled paper.
4
(07)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement