KOM300M Industrial Media Converter Hardware Installation Manual

KOM300M Industrial Media Converter Hardware Installation Manual
KOM300M User’s Manual 201110 KOM300M
Industrial Media Converter
Hardware Installation Manual
Kyland Technology Co., LTD.
Publication Date: Oct. 2011
Version: V1.0
Customer Service Hotline: (+8610) 88796676
FAX: (+8610) 88796678
Website: http://www.kyland.cn
E-mail: [email protected]
No.: 1.12.02.2009-0
1
KOM300M User’s Manual 201110 KOM300M Industrial Media Converter
Hardware Installation Manual
Disclaimer: Kyland Technology Co., Ltd. tries to keep the content in this manual as accurate and
as up-to-date as possible. This document is not guaranteed to be error-free, and we reserve the
right to amend it without notice to users.
Copyright © 2011 KYLAND Technology CO., LTD.
All rights reserved.
No part of this documentation may be excerpted, reproduced, translated, annotated or duplicated,
in any form or by any means without the prior written permission of KYLAND Corporation.
2
KOM300M User’s Manual 201110 Notice for Safety Operation
This product performs reliably as long as it is used according to the guidance. Artificial
damage or destruction of the equipment should be avoided.
z
Read this manual carefully and keep it for future reference;
z
Do not place the equipment near water sources or damp areas;
z
Do not place anything on power cable or put the cable in unreachable places;
z
Do not tie or wrap the cable, which may cause a fire risk.
z
Power connectors and other equipment connectors should be firmly interconnected
and checked frequently.
z
Do not repair the equipment by yourself, unless it is clearly specified in the manual.
z
Please keep the equipment clean; if necessary, wipe the equipment with soft cotton cloth.
In the following cases, please immediately remove power and contact your Kyland
representative:
z
Water gets into the equipment;
z
Equipment damage or shell breakage;
z
Equipment operation or performance has abnormally changed;
z
The equipment emits odor, smoke or abnormal noise.
3
KOM300M User’s Manual 201110 Contents
1.
Packing List .............................................................................................................................. 5
2.
Product Overview ..................................................................................................................... 5
3.
Structure and Interface ............................................................................................................. 5
3.1 Front Panel ........................................................................................................................ 5
3.2 Top Panel........................................................................................................................... 6
4.
Mounting .................................................................................................................................. 6
4.1 Dimension Drawing ........................................................................................................... 6
4.2 Mounting Steps.................................................................................................................. 8
5.
Cable Connection................................................................................................................... 10
5.1 10/100Base-T(X) Ethernet port........................................................................................ 11
5.2 100Base-FX Ethernet Port............................................................................................... 12
5.3 Power .............................................................................................................................. 13
5.4 Grounding ........................................................................................................................ 14
6.
LED Indicators........................................................................................................................ 15
7.
Management
access ........................................................................................................... 16
7.1 Connected through Ethernet cable .................................................................................. 16
7.2 Web interface .................................................................................................................. 18
8.
Product Models ...................................................................................................................... 18
9.
Basic Features and Specifications .........................................................................................19
4
KOM300M User’s Manual 201110 1.
Packing List
KOM300M Industrial Media Converter
1
Hardware Installation Manual
1
Certificate of Quality (including Warranty Card)
1
Note: After unpacking, please check the accessories and the appearance of the equipment. If
anything is missing or damaged, please contact us.
2.
Product Overview
KOM300M is a series of green low power consumption DIN-Rail industrial media
converter that can be applied extensively in wind power, distribution network
automation, subway PIS, power SCADA, wastewater treatment, metallurgy,
intelligent transportation, rail transit and many other industries.
KOM300M support telnet and web management methods, Kyvision centralized
management, FTP/TFTP upgrade, and support SNMPv1/v2/v3, LLDP, HTTP,
Modbus and TCP.
KOM300M industrial media converter supports DIN-Rail and panel mounting, and
supports IP40 protection class. It provides one 100Base-FX port and two
10/100Base-T(X) RJ45 ports in the front panel.
3.
Structure and Interface
3.1 Front Panel
5
KOM300M User’s Manual 201110 1: PWR1 -- Power 1 LED
2: PWR2 -- Power 2 LED
3: 1 -- 100Base-FX port LED
4: Run-Run LED
5: 1 -- 100Base-FX port
6: (2,3)-- two 10/100Base-T(X) RJ45 ports
7:RJ45 port Speed LED
8:RJ45 port Link/ACT LED
Figure 1 Front Panel
3.2 Top Panel
1: Terminal block for power input
2: Screw for grounding
Figure 2 Top Panel
4.
Mounting
4.1 Dimension Drawing
6
KOM300M User’s Manual 201110 z Dimension Drawing for DIN-Rail Mounting (Unit: mm)
Figure 3 DIN-Rail Mounting Dimension Drawing
z Dimension Drawing for Panel Mounting (Unit: mm)
Figure 4 Panel Mounting Dimension Drawing
Note: The switch housing is a part of the heat dissipation system, which becomes hot during
operation. Please be careful when handling the device during operation.
7
KOM300M User’s Manual 201110 4.2 Mounting Steps
z KOM300M DIN-Rail Mounting
The specific steps are as follows:
Step 1: Select the mounting position for KOM300M and ensure that there is
adequate space.
Step 2: Insert the top of the DIN-Rail into the slot of the DIN-Rail connecting
seat in the rear panel of KOM300M as seen in Figure 5; move the device in
the direction of arrow 2 to put the whole Din-Rail into the seat; verify the
KOM300M is firmly mounted on the DIN-Rail, as shown in Figure 5.
Figure 5 DIN-Rail Mounting
z Remove KOM300M from DIN-Rail
The specific steps are as follows:
Step 1: Insert the screwdriver into the hole at the bottom of spring locking
plate; press the plate down to loosen the connection of DIN-Rail and switch,
as shown in arrow 1
Step 2: Pull the KOM300M up in the direction of arrow 2; meanwhile remove
the device from the DIN-Rail along the direction of arrow 3.
8
KOM300M User’s Manual 201110 Figure 6 DIN-Rail Dismounting
z KOM300M Panel Mounting
The specific steps are as follows:
Step 1: Select the mounting position for KOM300M on the wall or in cabinet;
ensure that there is adequate space for the switch.
Step 2: Drill 4 holes on the selected position according to the panel mounting
dimension drawings; use a cross-screwdriver to screw 4 cross-slot screws
(M3×10) into holes. Don’t tighten the screws completely; leave about 5mm of
space between.
Step 3: Aim 4 mounting holes on KOM300M mounting plate at 4 fixed screws;
pass the screws through 4 holes with the diameter of 6.5mm (Ф6.5); then slide
down KOM300M as seen in arrow 2; finally screw 4 screws tightly. Now the
KOM300M should be firmly fixed to the wall or cabinet.
9
KOM300M User’s Manual 201110 Figure 7 Panel Mounting
z Remove KOM300M from wall or cabinet
The specific steps are as follows:
Step 1: Use a screwdriver to loosen 4 screws; move the device up to let
screws into 4 holes with the diameter of 6.5mm (Ф6.5) as seen in arrow 1.
Step 2: Unscrew the screws from wall or cabinet; remove the device from wall
or cabinet
Figure 8 Panel Dismounting
5.
Cable Connection
10
KOM300M User’s Manual 201110 5.1 10/100Base-T(X) Ethernet port
10/100Base-T(X) Ethernet RJ45 port can be connected to terminal equipment and
network devices with straight-through cables or crossover cables. RJ45
connectors must be equipped at both ends of cable.
z Pin definition of 10/100Base-T(X) RJ45 port
Pin number of 10/100Base-T(X) RJ45 port is shown in Figure 9
8 7 6 5 4 3 2 1
Figure 9 RJ45 Port
Pin definition of 10/100Base-T(X) RJ45 port is shown in Table 1
Table 1 Pin Definition of 10/100Base-T(X) RJ45 Port
Pin
1
MDI-X signal name
Receiving data+(RD+)
MDI signal name
Output data+(TD+)
2
3
Receiving data-(RD-)
Output data+(TD+)
Output data-(TD-)
Receiving data+(RD+)
6
4, 5, 7, 8
Output data-(TD-)
Receiving data-(RD-)
Unused
Unused
Note: “+”“-”means level polarity.
z
Wiring Sequence
Figure 10
10/100M Straight-through Cable Wiring
11
KOM300M User’s Manual 201110 Figure 11
10/100M Cross-over Cable Wiring
5.2 100Base-FX Ethernet Port
100Base-FX Ethernet port is equipped with FC/ST/SC connector, and each port
consists of TX (transmit) port and RX (receive) port, as seen on the left in Figure
12.
100Base-FX port wiring is shown on the right in Figure 12 (Take SC port as
example; ST/FC wiring method is the same with SC). Connect the TX (transmit)
port of device A to the RX (receive) port of device B, and the RX (receive) port of
device A to the TX (transmit) port of device in order to transmit data between
device A and device B.
Figure 12 100Base-FX Port Wiring
12
KOM300M User’s Manual 201110 Note: A laser is used to transmit signals in fiber cables. The laser meets the requirements of
level 1 laser products. Routine operation is not harmful to your eyes, but do not look directly at
the fiber port or fiber connector when the switch is powered on.
5.3 Power
According to the power input requirements, use a 5.08mm-spacing terminal block
to connect power cable.
Note: The cross section area of power cable is required to be greater than 0.75mm2 and less
than 2.5mm2. The grounding resistance requirement: <5Ω.
z
5 pin 5.08mm power terminal block
Figure 13 5-pin 5.08mm-spacing Plug-in Terminal Block
5 pin 5.08mm power terminal block contact definition
Table 2 Contact Definition
Contact number
DC wiring definition
AC wiring definition
1
PWR1: +
PWR1: L
2
PWR1: -
PWR1: N
3
Protection Ground
Protection Ground
4
PWR2: -
PWR2: N
13
KOM300M User’s Manual 201110 5
z
PWR2: +
PWR2: L
Wiring and mounting
Step 1: Take the power terminal block off KOM300M
Step 2: Insert the power cable into the terminal block and fix the power cable
Step 3: Put the terminal block back to KOM300M with the connected cable
5.4 Grounding
z
Chassis grounding and power terminal grounding
Figure 14 Chassis Grounding and Power Terminal Grounding
There is a grounding screw on the top panel of the KOM300M, which is for
chassis grounding. One end of the chassis grounding cable is connected with
the grounding screw and the other end of the cable is reliably grounded. (The
cross section area of chassis grounding cable should be more than 2.5mm2.
The grounding resistance requirement: <5Ω)
The grounding part in the 5.08mm power terminal block is called surge
grounding.
It is required to connect the chassis grounding part with the surge grounding
part by an 18#AWG yellow-green line as seen below
z
18#AWG yellow-green line
(Unit: mm)
14
KOM300M User’s Manual 201110 Figure 15 18#AWG Yellow-green Line
Note: If KOM300M needs to perform a dielectric voltage withstand test, in order to avoid test
failure, please disconnect the 18#AWG yellow-green line to disable surge protection circuit,
which connects to surge grounding.
Figure 16 Disconnect 18#AWG Yellow-green Line
6.
LED Indicators
Table 3 KOM300M LED Indicators
LED
State
Description
Power LEDs
15
KOM300M User’s Manual 201110 PWR1
PWR2
ON
Power 1 connects and operates normally.
OFF
Power 1 disconnects or operates abnormally.
ON
Power 2 connects and operates normally.
OFF
Power2 disconnects or operates abnormally.
Run LED
Run
Blinking
CPU is running normally at 1 Hz.
ON
CPU is running abnormally or the device is starting.
OFF
CPU is not started up.
10/100Base-T(X) RJ45 port LEDs
Speed
(Yellow)
Link/Act
(Green)
ON
100M working state
OFF
10M working state or no connection
ON
Effective network connection in the port
Blinking
Network activities in the port
OFF
No effective network connection in the port
100Base-FX port LED
LINK/ACT
7.
On
Effective network connection in the port
Blinking
Network activities in the port
Off
No effective network connection in the port
Management
access
Access the switch through the following two ways
7.1 Connected through Ethernet cable
First, connect any port of the device with the Ethernet port of a personal computer
through an RJ45 cable.
Second, open the Run window from the start menu, then input “telnet + ‘IP
address’”. Click “OK” to enter the Telnet interface. The default IP address is
192.168.0.2
16
KOM300M User’s Manual 201110 Figure 17 Enter Telnet
Third, click “OK”, and input a default user name “admin” and password “123” to
enter the Telnet configuration interface, see Figure 18.Type in a CLI command from
Table 4
Figure 18 Telnet Configuration Interface
Table 4 CLI Command
17
KOM300M User’s Manual 201110 View
Command
Description
User View
SWITCH>enable
Enter management view
Management View
SWITCH#show interface
Show the IP address of current device
Management View
SWITCH#show version
Show hardware and software versions
Management View
SWITCH#reboot
Reboot
Management View
SWITCH#load default
Reload factory default settings
Management View
SWITCH#config terminal
Enter configuration view
7.2 Web interface
First, connect the Ethernet port on the PC to any RJ45 port on the device.
Second, input the IP address of the current device in web browser , default IP is
192.168.0.2. The Web interface access screen will appear as shown below in
Figure 19, login with default user name “admin” and password “123”. Figure 19 Access Web Interface
8.
Product Models
The specific configuration models of KOM300M are shown in below table;
Table 5 KOM300M Configuration Table
Model
Description
Power
18
KOM300M User’s Manual 201110 1 100Base-FX port, SM/MM
12VDC, 24VAC/DC, dual
ports, FC/SC/ST connector;
KOM300M-1S/M-2T
redundant power inputs
2 10/100Base-T(X) RJ45 ports
The optional accessories of KOM300M are shown in below table;
Table 6 KOM300M Optional Accessories
9.
Model
Description
DT-BGAZ-01
Panel mounting kit
DT-FCZ-RJ45-01
RJ45 dustproof shield
Basic Features and Specifications
z
Power Requirements
Power input: 12VDC (9~18VDC), 24VAC/DC (18~72VDC, 18~50VAC)
Power terminal: 5-pin 5.08mm-spacing plug-in terminal block
Power consumption: full load: 2.6W(MAX)
z
Physical Characteristics
Housing:Metal,fanless
Installation: DIN-Rail or Panel mounting
Dimensions (W×H×D): 30mm×115mm×91.5mm
Weight: 0.3Kg
z
Environment Limits
Operating Temperature: -40℃ to 85℃
Storage Temperature: -40℃ to 85℃
Ambient Relative Humidity: 5% to 95% (non-condensing)
z
MTBF: 462741hrs
z
Warranty: 5 years
19
KOM300M User’s Manual 201110 For more information about KYLAND products, please visit our website:
http://www.kyland.cn/
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement