Compaq ProLiant 1600 Specifications

Compaq ProLiant 1600 Specifications
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
ProLiant 1600 and
ProLiant 1200 Servers
Maintenance and Service Guide
First Edition (October 1997)
Document Part Number 149036-001
Spares Part Number 298015-001
Compaq Computer Corporation
Notice
The information in this publication is subject to change without notice.
COMPAQ COMPUTER CORPORATION SHALL NOT BE LIABLE FOR TECHNICAL
OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN, NOR FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE
FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL. THIS
INFORMATION IS PROVIDED “AS IS” AND COMPAQ COMPUTER
CORPORATION DISCLAIMS ANY WARRANTIES, EXPRESS, IMPLIED OR
STATUTORY AND EXPRESSLY DISCLAIMS THE IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, GOOD TITLE AND
AGAINST INFRINGEMENT.
This publication contains information protected by copyright. No part of this publication
may be photocopied or reproduced in any form without prior written consent from Compaq
Computer Corporation.
 1997 Compaq Computer Corporation.
All rights reserved. Printed in the U.S.A.
The software described in this guide is furnished under a license agreement or
nondisclosure agreement. The software may be used or copied only in accordance with the
terms of the agreement.
Compaq, Compaq Insight Manager, QuickFind, registered United States Patent and
Trademark Office.
SoftPaq is a trademark and/or service mark of Compaq Computer Corporation.
Product names mentioned herein may be trademarks and/or registered trademarks of their
respective companies.
Compaq ProLiant 1600 and ProLiant 1200 Servers
Maintenance and Service Guide
First Edition (October 1997)
Document Part Number 149036-001
Spares Part Number 298015-001
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
iii
Contents
Preface
About This Guide
Symbols........................................................................................................................viii
Technician Notes..........................................................................................................viii
Where to Go for Help.....................................................................................................ix
Integrated Management Display .............................................................................ix
Electronic Services..................................................................................................ix
Compaq CDs ............................................................................................................x
Compaq Web Site ....................................................................................................x
Other Information Sources......................................................................................xi
Chapter 1
Illustrated Parts Catalog
Mechanical Parts Exploded View ............................................................................... 1-1
System Components Exploded View.......................................................................... 1-2
Spares Parts List.......................................................................................................... 1-3
Chapter 2
Removal and Replacement Procedures
Electrostatic Discharge Information ........................................................................... 2-1
Symbols in Equipment ................................................................................................ 2-2
Preparation Procedures ............................................................................................... 2-2
Rack Warnings ..................................................................................................... 2-3
Server Warnings and Precautions ........................................................................ 2-4
Front Bezel.................................................................................................................. 2-5
Feet.............................................................................................................................. 2-6
Left Side Access Panel................................................................................................ 2-7
Top Cover ................................................................................................................... 2-8
Right Side Access Panel.............................................................................................. 2-9
Mass Storage ............................................................................................................. 2-10
Hot-Plug Drive Cage.......................................................................................... 2-11
CD-ROM Drive.................................................................................................. 2-12
Diskette Drive .................................................................................................... 2-13
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
iv
Contents
Removal and Replacement Procedures (continued)
Cable Diagrams ......................................................................................................... 2-14
System I/O Board Cage............................................................................................. 2-16
I/O Fan ...................................................................................................................... 2-17
Power Switch............................................................................................................. 2-18
Processor Cage Assembly ......................................................................................... 2-20
Processor Cage................................................................................................... 2-20
Pentium II Adapter Board.................................................................................. 2-22
Terminator Board............................................................................................... 2-23
Processors .......................................................................................................... 2-24
Processor Power Module ................................................................................... 2-26
Memory Expansion Board ................................................................................. 2-28
Memory.............................................................................................................. 2-29
Power Supply ............................................................................................................ 2-33
Backplane Board ....................................................................................................... 2-34
External Replacement Battery .................................................................................. 2-35
Chapter 3
Diagnostic Tools
Utility Access .............................................................................................................. 3-2
Power-On Self-Test (POST) ....................................................................................... 3-4
Diagnostics Software................................................................................................. 3-17
Primary Processor Test Error Codes ................................................................. 3-18
Memory Test Error Codes ................................................................................. 3-19
Keyboard Test Error Codes ............................................................................... 3-20
Parallel Printer Test Error Codes....................................................................... 3-21
Video Display Unit Test Error Codes ................................................................ 3-21
Diskette Drive Test Error Codes........................................................................ 3-22
Monochrome Video Board Test Error Codes .................................................... 3-22
Serial Test Error Codes...................................................................................... 3-23
Modem Communications Test Error Codes ...................................................... 3-23
Fixed Disk Drive Test Error Codes.................................................................... 3-24
Tape Drive Test Error Codes ............................................................................. 3-25
Advanced VGA Board Test Error Codes........................................................... 3-26
Compaq Network Interface Cards Test Error Codes ......................................... 3-27
SCSI Fixed Disk Drive Test Error Codes .......................................................... 3-28
SCSI/IDE CD-ROM Drive Test Error Codes .................................................... 3-28
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
v
Diagnostic Tools (continued)
SCSI Tape Drive Test Error Codes.................................................................... 3-29
Server Manager/R Board Test Error Codes....................................................... 3-29
Pointing Device Interface Test Error Codes ...................................................... 3-30
Drive Array Advanced Diagnostics (DAAD)............................................................ 3-31
Integrated Management Log ..................................................................................... 3-42
Multiple Ways of Viewing the Log.................................................................... 3-42
Compaq Survey Utility....................................................................................... 3-43
List of Events ..................................................................................................... 3-44
Rapid Recovery Services........................................................................................... 3-46
Automatic Server Recovery-2............................................................................ 3-46
Server Health Logs............................................................................................. 3-55
Storage Fault Recovery Tracking....................................................................... 3-59
Storage Automatic Reconstruction .................................................................... 3-59
Network Interface Fault Recovery Tracking...................................................... 3-59
Memory Fault Recovery Tracking ..................................................................... 3-59
Remote Service Features........................................................................................... 3-60
ROMPaq.................................................................................................................... 3-61
Compaq Insight Manager.......................................................................................... 3-61
Features of Compaq Insight Management ......................................................... 3-61
Compaq Insight Management Software Architecture........................................ 3-62
Chapter 4
Connectors, Switches, and Jumpers
Compaq ProLiant 1600 Processor Board.................................................................... 4-1
Components ......................................................................................................... 4-1
Rear Connectors and LEDs.................................................................................. 4-2
SW1 - Bus/Core Ratio Settings............................................................................ 4-3
Compaq ProLiant 1200 Processor Board.................................................................... 4-4
Components ......................................................................................................... 4-4
Rear Connectors and LEDs.................................................................................. 4-5
SW1 - Bus/Core Ratio Settings............................................................................ 4-6
System I/O Board........................................................................................................ 4-7
Components ......................................................................................................... 4-7
Rear Connectors................................................................................................... 4-8
SW1 - System Maintenance Switch ..................................................................... 4-9
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
vi
Contents
Chapter 5
Physical and Operating Specifications
System Unit ................................................................................................................. 5-2
Power Supply .............................................................................................................. 5-3
Compaq ProLiant 1600 ........................................................................................ 5-3
Compaq ProLiant 1200 ........................................................................................ 5-4
Dual Inline Memory Modules (DIMMs) .................................................................... 5-4
1.44-MB Diskette Drive.............................................................................................. 5-5
16X CD-ROM Drive ................................................................................................... 5-6
Index
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
vii
Preface
About This Guide
This Maintenance and Service Guide is a troubleshooting guide that can be used for
reference when servicing Compaq ProLiant 1600 and ProLiant 1200 Servers.
WARNING: To reduce the risk of personal injury from
electrical shock and hazardous energy levels, only
authorized service technicians should attempt to repair this
equipment. Improper repairs could create conditions that
are hazardous.
IMPORTANT: The installation of options and the servicing of this
product shall be performed by individuals who are knowledgeable
of the procedures, precautions, and hazards associated with
equipment containing hazardous energy circuits.
Compaq Computer Corporation reserves the right to make changes to Compaq
ProLiant 1600 and ProLiant 1200 Servers without notice. This document contains the
following chapters:
■
Chapter 1 - Illustrated Parts Catalog
Contains Compaq ProLiant 1600 and ProLiant 1200 Servers exploded views and
spares parts list.
■
Chapter 2 - Removal and Replacement Procedures
Contains steps for removing and replacing Compaq ProLiant 1600 and ProLiant 1200
Servers spare parts.
■
Chapter 3 - Diagnostic Tools
Describes software and firmware diagnostic tools available for all Compaq
server products.
■
Chapter 4 - Connectors, Switches, and Jumpers
Provides connector, switch, and jumper information for the Compaq ProLiant 1600
and ProLiant 1200 Servers.
■
Chapter 5 - Physical and Operating Specifications
Provides the physical and operating specifications for the Compaq ProLiant 1600 and
ProLiant 1200 Servers.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
viii
About This Guide
Symbols
The following text and symbols mark special information throughout this guide:
WARNING: Text set off in this manner indicates that failure to
follow directions in the warning could result in bodily harm or
loss of life.
CAUTION: Text set off in this manner indicates that failure to
follow directions could result in damage to equipment or loss
of data.
IMPORTANT: Text set off in this manner presents clarifying
information or
specific instructions.
NOTE: Text set off in this manner presents commentary, sidelights,
or interesting points of information.
Technician Notes
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
ix
WARNING: To reduce the risk of personal injury from
electrical shock and hazardous energy levels, do not exceed
the level of repair specified in these procedures. Because of
the complexity of the individual boards and subassemblies,
do not attempt to make repairs at the component level or to
make modifications to any printed wiring board. Improper
repairs could create conditions that are hazardous.
WARNING: To reduce the risk of electric shock or damage
to the equipment:
■
If the system has multiple power supplies,
disconnect power from the system by
unplugging all power cords from the power
supplies.
■
Do not disable the power cord grounding plug.
The grounding plug is an important safety
feature.
■
Plug the power cord into a grounded (earthed)
electrical outlet that is easily accessible at all
times.
CAUTION: To properly ventilate your system, you must
provide at least
12 inches (30.5 cm) of clearance at the front and back of
the computer.
IMPORTANT: Any indication of repair at the component level or
modification of a printed wiring board may void any warranty.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
x
About This Guide
Where to Go for Help
Major sources of additional information are as follows:
■
Integrated Management Display
■
Electronic services
■
Compaq CDs
■
Compaq Web Site (http://www.compaq.com)
■
Other information sources
Integrated Management Display
The Compaq Integrated Management Display (IMD) is an integrated, 16x4 character
display mounted on the front of the server. This display provides easy-to-use, menu-driven
access to server information, including model number, LCD firmware revision, and POST
operations.
Electronic Services
Users can download drivers, patches, and Compaq service updates from the following
sources:
■
Internet: Questions can be submitted to Compaq Technical Support staff using the
electronic mail address: [email protected] Compaq files can be accessed
using the address: FTP.COMPAQ.COM. Enter "anonymous" for the user name at
the log-in prompt and enter your full Internet electronic mail address for the
password. You can access the Compaq World Wide Web site through the Uniform
Resource Locator (URL): http://www.compaq.com.
■
Other online services: CompuServe, Prodigy, and America Online, can be used if
you are a member. Use the keywords below to access Compaq materials:
■
❏
CompuServe - The keywords are “GO COMPAQ”.
❏
Prodigy - Choose the “Jump” navigation command, then enter the keyword
“COMPAQ”.
❏
America Online - Enter the keyword “COMPAQ”.
Compaq Download Facility: Call 1-281-518-1418
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
xi
Compaq CDs
Compaq offers the following CDs, which contain Compaq documentation and other
information.
Compaq Systems Reference Library CD
Compaq Systems Reference Library CD is located in the Reference Information pack and
includes the following online documents:
■
Diagnostics
■
Insight Manager documentation
■
Integration TechNotes
■
Part number lists
■
SCSI and other options guides
■
Security Management
■
Server Maintenance and Service Guides (MSGs)
■
Server reference guides
Compaq SmartStart and Support Software CD
Compaq SmartStart and Support Software CD is located in the Server Setup and
Management pack and contains:
■
System Configuration Utility software
■
ROMPaq
■
Drivers
Compaq Management CD
Compaq Management CD is located in the Server Setup and Management pack
and contains:
■
Insight Manager Utility software
■
Online Help for the Insight Manager Utility
Compaq Web Site
The latest product updates and Compaq information are available on the Internet at the
Compaq World Wide Web site. Access the site through the following address:
http://www.compaq.com
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
xii
About This Guide
Other Information Sources
In addition to this guide, the following information sources are available:
■
User Documentation
■
Compaq Service Quick Reference Guide
■
Service Training Guides
■
Compaq Service Advisories and Bulletins
■
Compaq QuickFind
■
Compaq Insight Manager
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
1-1
Chapter 1
Illustrated Parts Catalog
This chapter provides the illustrated parts breakdown and a spares parts list for the Compaq
ProLiant 1600 and ProLiant 1200 Servers. See Table 1-1 for the names of referenced spare
parts.
Mechanical Parts Exploded View
4
3
22 23
1
13
2
11
17 20
5
14 15
7
8
3
6
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
1-2
Illustrated Parts Catalog
Figure 1-1. Exploded View of the Compaq ProLiant 1600 and ProLiant 1200 Server Mechanical Parts
System Components Exploded View
12
9 10
22 23
1
2
29
30
25
20
8
27
19
24
17
24
16
18
1600
21
26
21
28
1200
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
1-3
Figure 1-2. Exploded View of the Compaq ProLiant 1600 and ProLiant 1200 Server System
Components
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
1-4
Illustrated Parts Catalog
Spares Parts List
Table 1-1
Spares Parts List - Compaq ProLiant 1600 and ProLiant 1200 Servers
Item
Description
CHASSIS
1
Chassis (ProLiant 1600 only)
Spares Part #
298011-001
2
Chassis (ProLiant 1200 only)
333560-001
3
Top Cover and Left Side Access Panel
271927-001
4
Right Side Access Panel
298013-001
5
Front Bezel
298012-001
6
Front Bezel Plate (Rack-Mountable model only)
271924-001
7
Feet (Tower model only)
333575-001
8
Hot-Plug Drive Cage, 3 x 1.6-inch
SYSTEM COMPONENTS
9
Power Supply, 280W (ProLiant 1200 only)
10 Power Supply, 325W with Bracket (ProLiant 1600 only)
11 Fan with bracket
12 4.5 V Battery Replacement
250909-001
333594-001
271916-001
281844-001
160274-001
13
Power Switch and Bracket
271929-001
14
Power Supply Rear Panel (ProLiant 1600 only)
270265-001
15
Power Supply Rear Panel (ProLiant 1200 only)
BOARDS
Processor with Heatsink, 233/66, 512KB (ProLiant 1200 only)
Processor Board, without Processor, with Cage and Fan
(ProLiant 1200 only)
333576-001
16
17
278262-001
149088-001
18
19
20
Processor, with Heat Sink 266/66 (ProLiant 1600 only)
333561-001
Processor Board, without Processor (ProLiant 1600 only)
149085-001
Processor Board, Dual SCSI, with Cage and Fan (ProLiant 1600 149089-001
only)
21
Memory Expansion Board
270183-001
22
System I/O Board, (PCI-P6), with cage (ProLiant 1200 only)
149039-001
23
System I/O Board, (PCI-P6), with cage (ProLiant 1600 only)
333570-001
24
Processor Power Module
299306-001
25
Backplane Board, PCI, Dual SCSI
149046-001
26
Processor Terminator Board
270119-001
Continued
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
1-5
Spares Parts List - Compaq ProLiant 1600 and ProLiant 1200 Servers
Continued
Item
27
28
Description
MEMORY
16-MB Dual Inline Memory Module (EDO, buffered, 60-ns)
32-MB Dual Inline Memory Module (EDO, buffered, 60-ns)
Spares Part #
289746-001
281857-001
MASS STORAGE DEVICES
29
3-Mode 1.44-MB Diskette Drive
333562-001
30
16X CD-ROM Drive
278791-001
CABLES
31
Diskette Cable
271928-001 *
32
Point to Point SCSI Cable
149097-001 *
33
IDE/CD Cable
271936-001 *
34
SCSI DAT/DLT Cable
300926-001 *
35
Parallel Cable
271938-001 *
36
Diskette/CD-ROM Power Cable
271939-001 *
37
SCSI Adapter Kit 50-to-68, Female
189638-001 *
MISCELLANEOUS
38
Country Kit (ProLiant 1200 only)
333569-001 *
39
Country Kit (ProLiant 1600 only)
333568-001 *
40
Country Kit (ProLiant 1600 Rack-Mountable model only)
333567-001 *
41
Return Kit
298017-001 *
42
Carton and Buns (International)
298017-002 *
43
Maintenance and Service Guide
298015-001 *
44
Illustrated Parts Map
298016-001 *
45
Slide Rail, 22-inch, Pair
165689-002 *
OPTIONS
46 64-MB Dual Inline Memory Module (EDO, buffered, 60-ns)
47 128-MB Dual Inline Memory Module (EDO, buffered, 60-ns)
48 Hot-Plug Drive Cage, 5 x 1.0-inch
281858-001 *
281859-001 *
250911-001 *
49
Duplexed Hot-Plug Drive Cage, 4 x 1.0-inch
271932-001 *
50
Rack Conversion Kit
333574-001 *
51
Integrated Management Display
271930-001 *
52
9.1-GB Non-Hot-Pluggable Wide Ultra 1.6-inch Hard Drive
199886-001 *
53
9.1-GB Hot-Pluggable Wide Ultra 1.6-inch Hard Drive
199888-001 *
54
9.1-GB Non-Hot-Pluggable Fast-SCSI-2 Hard Drive
199885-001 *
55
4.3-GB Hot-Pluggable Wide Ultra 1-inch Hard Drive
242622-001 *
56
4.3-GB Non-Hot-Pluggable Wide Ultra 1-inch Hard Drive
242606-001 *
57
4.3-GB Hot-Pluggable Fast-Wide SCSI-2 Hard Drive
199598-001 *
58
4.3-GB Non-Hot-Pluggable Fast-Wide SCSI-2 Hard Drive
199599-001 *
59
4.3-GB Hot-Pluggable Fast-SCSI-2 Hard Drive
199584-001 *
60
4.3-GB Non-Hot-Pluggable Fast-SCSI-2 Hard Drive
199585-001 *
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
1-6
Illustrated Parts Catalog
Spares Parts List - Compaq ProLiant 1600 and ProLiant 1200 Servers
Continued
Item
Description
Spares Part #
OPTIONS (continued)
61
2.1-GB Hot-Pluggable Wide Ultra 1-inch Hard Drive
242603-001 *
62
2.1-GB Non-Hot-Pluggable Wide Ultra 1-inch Hard Drive
242604-001 *
63
2.1-GB Hot-Pluggable Fast-Wide SCSI-2 1-inch Hard Drive
199878-001 *
64
2.1-GB Hot-Pluggable Fast-Wide SCSI-2 Hard Drive
199643-001 *
65
2.1-GB Non-Hot-Pluggable Fast-Wide SCSI-2 Hard Drive
199644-001 *
66
2.1-GB Hot-Pluggable Fast-Wide SCSI-2 Hard Drive
199428-001 *
67
2.1-GB Non-Hot-Pluggable Fast-SCSI-2 Hard Drive
142272-001 *
68
1.05-GB Hot-Pluggable Fast-SCSI-2 Hard Drive
146717-001 *
69
1.05-GB Non-Hot-Pluggable Fast-SCSI-2 Hard Drive
146799-001 *
70
1-inch Drive Tray SCA Connector
242801-001 *
71
1-inch Drive Tray, Fast-Wide Connector
199880-001 *
72
1-inch Drive Tray, Fast-SCSI-2 Connector
242593-001 *
73 1.6-inch Drive Tray, Fast-SCSI-2 Connector
* Not Shown
199656-001 *
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-1
Chapter 2
Removal and Replacement
Procedures
This chapter provides subassembly/module-level removal and replacement procedures for
the ProLiant 1600 and ProLiant 1200 Servers. After completing all necessary removal and
replacement procedures, run the Diagnostics program to verify that all components
operate properly.
To service Compaq ProLiant 1600 and ProLiant 1200 Servers, you might need
the following:
■
Torx T-15 screwdriver
■
From the Compaq SmartStart and Support Software CD:
❏
System Configuration Utility software
❏
Drive Array Advanced Diagnostics software
❏
Diagnostics software
Electrostatic Discharge Information
A discharge of static electricity can damage static-sensitive devices or microcircuitry.
Proper packaging and grounding techniques are necessary precautions to prevent damage.
To prevent electrostatic damage, observe the following precautions:
■
Transport products in static-safe containers such as conductive tubes, bags,
or boxes.
■
Keep electrostatic-sensitive parts in their containers until they arrive at static-free
stations.
■
Cover work stations with approved static-dissipating material. Provide a wrist strap
connected to the work surface and properly grounded tools and equipment.
■
Keep work area free of non-conductive materials such as ordinary plastic assembly
aids and foam packing.
■
Make sure you are always properly grounded when touching a static-sensitive
component or assembly.
■
Avoid touching pins, leads, or circuitry.
■
Always place drives PCB assembly side down.
■
Use conductive field service tools.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-2
Removal and Replacement Procedures
Symbols in Equipment
WARNING: Any surface or area of the equipment
marked with these symbols indicates the presence
of a hot surface or hot component. If this surface
is contacted, the potential for injury exists. To
reduce the risk of injury from a hot component,
allow the surface to cool before touching.
WARNING: Any surface or area of the equipment
marked with these symbols indicates the presence
of electrical shock hazards. The enclosed area
contains no operator serviceable parts. To reduce
the risk of injury from electrical shock hazards, do
not open this enclosure.
WARNING: Any RJ-45 receptacle marked with
these symbols indicates a Network Interface
Connection. To reduce the risk of electrical shock,
fire, or damage to the equipment, do not plug
telephone or telecommunications connectors into
this receptacle.
CLASS 1 LASER PRODUCT
WARNING: This label or equivalent is located on
the surface of your CD-ROM drive. This label
indicates that the product is classified as a CLASS
1 LASER PRODUCT.
Preparation Procedures
Before beginning any of the removal and replacement procedures for non-hot-plug devices:
1.
Turn off the server.
2.
Disconnect the AC power cord from the AC outlet, then from the server.
3.
Disconnect all external peripheral devices from the server.
4.
For some removal and replacement procedures, you must remove the server from
the rack and place it on a sturdy table or workbench. Refer to the ProLiant 1600 and
ProLiant 1200 Servers Setup and Installation Guide for instructions.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-3
WARNING: Because the rack allows you to stack computer
components on a vertical rather than horizontal plane, you
must take precautions to provide for rack stability and safety.
It is important that you follow these precautions to provide
for rack stability and safety, and to protect both personnel
and property. Heed all cautions and warnings throughout
the installation instructions that came with the server.
CAUTION: Electrostatic discharge can damage electronic
components. Be sure you are properly grounded before
beginning any installation procedure. See the section titled
“ Electrostatic Discharge Information” in this chapter, for
more information.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-4
Removal and Replacement Procedures
Rack Warnings
WARNING: To reduce the risk of personal injury, make sure
that the rack is adequately stabilized before extending a
component outside the rack. A rack may become unstable
if more than one component is extended for any reason.
Extend only one component at a time.
WARNING: To reduce the risk of personal injury or damage
to the equipment, be sure that:
■
The leveling jacks are extended to the floor.
■
The full weight of the rack rests on the leveling jacks.
■
The stabilizers are attached to the rack if it is a single rack
installation.
■
The racks are coupled together in multiple rack
installations.
WARNING: To reduce the risk of electric shock or damage
to the equipment:
■
Do not disable the power cord grounding plug. The
grounding plug is an important safety feature.
■
Plug the power cord into a grounded (earthed) electrical
outlet that is easily accessible at all times.
■
Install the power supply before connecting the power
cord to the power supply.
■
Unplug the power cord before removing the power
supply from the server.
■
If the system has multiple power supplies, disconnect
power from the system by unplugging all power cords
from the power supplies.
CAUTION: The Compaq ProLiant Server must always be
operated with the system unit cover on. Proper cooling will
not be achieved if the system unit cover is removed.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-5
Server Warnings and Precautions
WARNING: To reduce the risk of personal injury from hot
surfaces, allow the internal system components to cool
before touching.
WARNING: To reduce the risk of electric shock or damage
to the equipment:
■
Do not disable the power cord grounding plug. The
grounding plug is an important safety feature.
■
Plug the power cord into a grounded (earthed) electrical
outlet that is easily accessible at all times.
■
Disconnect power from the server by unplugging the
power cord from either the electrical outlet or the server.
CAUTION: Protect the server from power fluctuations and
temporary interruptions with a regulating uninterruptible
power supply (UPS). This device protects the hardware from
damage caused by power surges and voltage spikes and
keeps the system in operation during a power failure.
CAUTION: The ProLiant 1600 and ProLiant 1200 Servers must
always be operated with the system unit cover on. Proper
cooling will not be achieved if the system unit cover is
removed.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-6
Removal and Replacement Procedures
Front Bezel
To remove the front bezel:
1.
Unlock the front bezel keylock.
2.
Open the front bezel.
3.
Lift up the front bezel and pull it away from the chassis.
Figure 2-1. Removing the Front Bezel
Reverse steps 1 through 3 to replace the front bezel.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-7
Feet
To remove the feet from the chassis, one at a time:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the front bezel. See page 2-6.
3.
Place the server on its left side.
4.
Remove the T-15 screw from each foot ➊.
5.
Pivot each foot down ➋, and pull it off the base of the chassis ➌.
3
2
1
Figure 2-2. Removing the Feet From the Chassis
Reverse steps 1 through 5 to replace the feet. Make sure each foot snaps securely
in its holders.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-8
Removal and Replacement Procedures
Left Side Access Panel
Remove the top cover to service the hot-plug drive cage, CD-ROM drive, power supply,
and backplane board. To remove the left side access panel:
WARNING: To reduce the risk of personal injury from hot
surfaces, allow the internal system components to cool
before touching them.
1.
Perform the preparation procedures. See page 2-2.
2.
Open the front bezel.
3.
Loosen the two thumbscrews attaching the left side access panel to the front of
the chassis.
4.
Slide the left side access panel back and pull it away from the chassis.
Figure 2-3. Removing the Left Side Access Panel
Reverse steps 1 through 4 to replace the left side access panel.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-9
Top Cover
Remove the top cover to service the PCI and EISA boards, system switches, signal cables,
I/O fan, Integrated Management Display (if installed), and the power switch.
WARNING: To reduce the risk of personal injury from hot
surfaces, allow the internal system components to cool
before touching them.
To remove the top cover:
1.
Perform the preparation procedures. See page 2-2.
2.
Open the front bezel.
3.
Loosen the thumbscrew attaching the top cover to the chassis ➊.
4.
Slide the top cover back and out ➋.
5.
Lift the top cover from the chassis.
2
1
Figure 2-4. Removing the Top Cover
Reverse steps 1 through 5 to replace the top cover.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-10
Removal and Replacement Procedures
Right Side Access Panel
Remove the right side access panel to convert from tower to rack or to replace a damaged
panel. To remove the right side access panel from the chassis:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the front bezel. See page 2-6.
3.
Remove the feet on the base of the right side access panel. See page 2-7.
4.
Remove the two T-15 screws securing the right side access panel to the front
of the chassis.
5.
Pull the right side access panel back and away from the chassis.
Figure 2-5. Removing the Right Side Access Panel
Reverse steps 1 through 5 to replace the right side access panel.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-11
Mass Storage
Compaq ProLiant 1600 and ProLiant 1200 Servers ship standard with a hot-plug drive cage
containing three 1.6-inch hot-plug drive bays. Four removable media bays contain one
third-height diskette drive and one half-height IDE CD-ROM drive. Two bays can contain a
second CD-ROM, tape drives, hard drives, or any SCSI device.
The Compaq ProLiant 1600 and ProLiant 1200 Servers support up to seven mass storage
devices. The following table and illustration describe the drive configurations.
6
5
4
3
2
Removable
Media
Area
1
0
Hot-Pluggable
Hard Drive
Bays
Hot-Pluggable
Figure 2-6. Server Drive Positions
Table 2-1
Description of Drive Bays
Drive
Position
0
Configuration
Hot-Plug Drive Bay
1
Hot-Plug Drive Bay
2
Hot-Plug Drive Bay
3
Media Slot
4
Media Slot
5
CD-ROM Drive
6
Diskette Drive
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-12
Removal and Replacement Procedures
Hot-Plug Drive Cage
To remove the hot-plug drive cage:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the front bezel. See page 2-6.
3.
Remove the left side access panel. See page 2-8.
4.
Disconnect all cables from the hot-plug drive cage.
5.
Remove the four T-15 screws.
6.
Slide the hot-plug drive cage out the front of the chassis.
Figure 2-7. Removing the Hot-Plug Drive Cage
CAUTION: Make sure that all power and signal cables to
the hot-plug drive cage have been reseated properly.
Reverse steps 1 through 6 to replace the hot-plug drive cage.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-13
CD-ROM Drive
To remove the CD-ROM drive:
1.
Perform the preparation procedures. See page 2-2.
2.
Open the front bezel.
3.
Remove the left side access panel. See page 2-8.
4.
Remove the two T-15 screws and washers from the front of the drive.
5.
Disconnect the CD-ROM cable.
6.
Slide the CD-ROM drive out the front of the chassis.
7.
Disconnect the power cable.
Figure 2-8. Removing the CD-ROM Drive
Reverse steps 1 through 7 to replace the CD-ROM drive.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-14
Removal and Replacement Procedures
Diskette Drive
To remove the diskette drive:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the front bezel. See page 2-6.
3.
Remove the top cover. See page 2-9.
4.
Disconnect all cables from the diskette drive.
5.
Remove the two T-15 screws and washers from the front of the drive.
6.
Slide the diskette drive out the front of the chassis.
Figure 2-9. Removing the Diskette Drive
Reverse steps 1 through 6 to replace the diskette drive.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-15
Cable Diagrams
Figure 2-10. IDE CD-ROM Drive Cable Diagram
Figure 2-11. Diskette Drive Cable Diagram
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-16
Removal and Replacement Procedures
Figure 2-12. Hot-Plug Drive Cage Cable Folding and Routing Diagram (ProLiant 1600)
Figure 2-13. Hot-Plug Drive Cage Cable Folding and Routing Diagram (ProLiant 1200)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-17
System I/O Board Cage
The system I/O board cage contains the system I/O board with PCI slots, system switches,
EISA slots, and the battery. Four slots are PCI/EISA; two are PCI only, for a total of six
slots.
To remove the system I/O board cage:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the top cover. See page 2-9.
3.
Disconnect all cables from the system I/O board cage.
4.
Remove any installed boards. Place them on a non-conductive work surface. You
will install them on the replacement system I/O board cage.
5.
Remove the two security screws (if installed).
6.
Push down on the cage ejector lever ➊, and pull out ➋.
7.
Pull the system I/O board cage out the back of the chassis ➌.
1
2
3
Figure 2-14. Removing the System I/O Board Cage
Reverse steps 1 through 7 to replace the system I/O board cage. Install any boards removed
in step 4 onto the replacement system I/O board cage.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-18
Removal and Replacement Procedures
I/O Fan
To remove the I/O fan:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the top cover. See page 2-9.
3.
Loosen the single thumbscrew attaching the I/O fan to the chassis ➊.
4.
Tilt the top of the I/O fan forward and away from the chassis ➋.
5.
Disconnect the I/O fan cable and slide it out of the clip ➌.
6.
Lift the I/O fan away from the chassis.
1
2
3
Figure 2-15. Removing the I/O Fan
Reverse steps 1 through 6 to replace the I/O fan.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-19
Power Switch
To remove the power switch and cable assembly:
1.
Perform the preparation procedures. See page 2-2.
WARNING: Any surface or area of the equipment
marked with these symbols indicates the presence
of electrical shock hazards. The enclosed area
contains no operator-serviceable parts. To reduce
the risk of injury from electrical shock hazards, do
not open this enclosure.
2. Remove the front bezel. See page 2-6.
3. Remove the top cover. See page 2-9.
4. Remove the single T-15 screw ➊.
5. Slide the power switch housing back ➋ and lift it out of the chassis ➌.
2
3
1
Figure 2-16. Removing the Power Switch Housing
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-20
Removal and Replacement Procedures
6. Unwind the power supply cables and LED cables from the strain-relief casing and
disconnect them from the power switch.
Power
SCSI
Activity
Figure 2-17. Disconnecting the Power Switch Cables
Reverse steps 1 through 6 to replace the power switch and cable assembly.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-21
Processor Cage Assembly
The processor cage assembly contains the processor cage, processor board, Pentium II
adapter board (ProLiant 1600 only), processor, processor power module, terminator board,
memory expansion board, and memory. See Chapter 1, “Illustrated Parts Catalog,” for the
spares parts numbers for these items.
Processor Cage
To remove the processor cage:
1.
Perform the preparation procedures. See page 2-2.
2.
Disconnect all cables from the processor cage assembly.
3.
Remove the two security screws (if installed).
4.
Push down on the processor cage ejector lever ➊, and pull out ➋.
2
1
Figure 2-18. Pulling Out the Processor Cage Lever
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-22
Removal and Replacement Procedures
5. Pull the processor cage out through the back of the chassis.
Figure 2-19. Removing the Processor Cage
Reverse steps 1 through 5 to replace the processor cage.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-23
Pentium II Adapter Board
The Pentium II adapter board ships standard in Compaq ProLiant 1600 only. To remove
the Pentium II adapter board:
IMPORTANT: If a single processor is installed, a terminator board
must be installed (Compaq ProLiant 1600 only).
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the processor cage (see page 2-21) and open the cage door.
3.
Lift up two levers on each end ➊ of the Pentium II adapter board.
4.
Lift the Pentium II adapter board from the processor cage ➋.
1
1
2
Figure 2-20. Removing the Pentium II Adapter Board
Reverse steps 1 through 4 to replace the Pentium II adapter board.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-24
Removal and Replacement Procedures
Terminator Board
IMPORTANT: If a single processor is installed, a terminator board
must be installed (Compaq ProLiant 1600 only).
To remove the terminator board from the Compaq ProLiant 1600:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the processor cage (see page 2-21) and open the cage door.
3.
Lift up two levers on each end of the terminator board ➊.
4.
Lift the terminator board from the processor cage ➋.
1
1
2
Figure 2-21. Removing the Terminator Board
Reverse steps 1 through 4 to replace the terminator board.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-25
Processors
Compaq ProLiant 1600
To remove the Compaq ProLiant 1600 processor:
IMPORTANT: If a single processor is installed, a terminator board
must be installed (Compaq ProLiant 1600 only).
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the processor cage (see page 2-21) and open the cage door.
3.
Remove the Pentium II adapter board and place it on a non-conductive work
surface. See page 2-23.
4.
Push in the latches on each side of the processor until you hear two clicks ➊. This
locks the tabs in the open position.
5.
Slide the processor from the Pentium II adapter board ➋.
1
2
1
Figure 2-22. Removing the Processor from the Compaq ProLiant 1600 Server
Reverse steps 1 through 5 to replace the Compaq ProLiant 1600 processor.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-26
Removal and Replacement Procedures
Compaq ProLiant 1200
To remove the Compaq ProLiant 1200 processor:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the processor cage (see page 2-21) and open the cage door.
3.
Push in the latches on each side of the processor until you hear two clicks ➊. This
locks the tabs in the open position.
4.
Lift the processor from the processor board ➋.
1
1
1
2
Figure 2-23. Removing the Processor from the Compaq ProLiant 1200 Server
Reverse steps 1 through 4 to replace the Compaq ProLiant 1200 processor.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-27
Processor Power Module
Compaq ProLiant 1600
To remove the processor power module from a Compaq ProLiant 1600 Server:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the processor cage (see page 2-21) and open the cage door.
3.
Remove the Pentium II adapter board and place it on a non-conductive work
surface. See page 2-23.
4.
Pull out the clips on each end of the processor power module ➊.
5.
Slide the processor power module from the Pentium II adapter board ➋.
1
2
Figure 2-24. Removing the Processor Power Module from the Compaq ProLiant 1600
Server
Reverse steps 1 through 5 to replace a processor power module in the Compaq ProLiant
1600 Server. The clips on the processor power module will snap into a locked position
automatically when the processor power module is pushed into the slot.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-28
Removal and Replacement Procedures
Compaq ProLiant 1200
To remove a processor power module from a Compaq ProLiant 1200 Server:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the processor cage (see page 2-21) and open the cage door.
3.
Remove the processor. See page 2-26.
4.
Pull out the clips on each end of the processor power module ➊.
5.
Lift the processor power module from the processor board ➋.
1
2
Figure 2-25. Removing the Processor Power Module from the Compaq ProLiant 1200
Server
Reverse steps 1 through 5 to replace a processor power module in the Compaq ProLiant
1200 Server. The clips on the processor power module will snap into a locked position
automatically when the processor power module is pushed into the slot.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-29
Memory Expansion Board
To remove the memory expansion board:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the processor cage. See page 2-21.
3.
Lift up the locking levers on each side of the memory board ➊.
4.
Lift up the memory expansion board to unplug it from the processor board slot ➋.
1
2
Figure 2-26. Removing the Memory Expansion Board
Reverse steps 1 through 4 to replace the memory expansion board.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-30
Removal and Replacement Procedures
Memory
Compaq ProLiant 1600 Servers ship standard with 64 megabytes of memory (two 32-MB
DIMMs) installed on the processor board. Memory is expandable to 512 megabytes.
Compaq ProLiant 1200 Servers ship standard with 32 megabytes of memory (two 16-MB
DIMMs) installed on the memory board. Memory is expandable to 512 megabytes.
J4
J3
J2
J1
Figure 2-27. DIMM Sockets on the Processor Board (Compaq ProLiant 1600 only)
J12
Bank 6
J11
J10
Bank 5
J9
Bank 4
J8
J7
Bank 3
J6
J5
Note: Both slots in a bank must be populated.
Figure 2-28. DIMM Sockets on the Memory Expansion Board
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-31
The following guidelines MUST be followed when installing or replacing memory:
■
Use 60-ns or faster; 16-, 32-, 64-, or 128-MB; EDO 4-K refresh DIMMs.
■
DIMMs must be installed in matched pairs that are identical in size and speed.
However, each pair of DIMMs need not be of the same size. For example, two
16-MB DIMMs can be installed in sockets 1 and 2, and two 32-MB DIMMs can be
installed in sockets 3 and 4.
■
To optimize system performance, fill the DIMM sockets in the following order,
keeping in mind that some sockets may already be filled or are not included in your
model:
❏
Bank 1: DIMM sockets 1 and 2 on the processor board (ProLiant 1600 only)
❏
Bank 3: DIMM sockets 5 and 6 on the memory expansion board
❏
Bank 2: DIMM sockets 3 and 4 on the processor board (ProLiant 1600 only)
❏
Bank 4: DIMM sockets 7 and 8 on the memory expansion board
❏
Bank 5: DIMM sockets 9 and 10 on the memory expansion board
❏
Bank 6: DIMM sockets 11 and 12 on the memory expansion board
CAUTION: Use only Compaq DIMMs. DIMMs from other
sources may adversely affect data integrity. Power-On SelfTest (POST) will warn of non-supported DIMMs.
To remove a DIMM:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the processor cage and place it on a non-conductive work surface. See page
2-21. Open the cage door.
3.
Locate the appropriate DIMM socket on the processor board or the memory
expansion board. If necessary, remove the memory expansion board and place it on
a non-conductive work surface. See page 2-29.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-32
Removal and Replacement Procedures
4.
Push the levers on each end of the memory module ➊.
5.
Pull the module from the board ➋.
1
2
1
Figure 2-29. Removing a DIMM from the Processor Board (ProLiant 1600 only)
2
1
1
Figure 2-30. Removing a DIMM from the Memory Expansion Board
Reverse steps 1 through 5 to replace the DIMM. The DIMM can be installed in only one
way. Match the notch on the module with the tab on the memory socket. Push the module
down into the socket, making sure that the module is fully inserted and properly seated.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-33
The following tables show possible memory upgrade configurations for Compaq ProLiant
1600 and 1200 Servers.
Table 2-2
Examples of DIMM Upgrade Combinations Compaq ProLiant 1600
Total
Memory
Bank 1
Bank 2
Bank 3
64 MB
2 x 32 MB
128 MB
2 x 32 MB
256 MB
2 x 32 MB
2 x 32 MB
2 x 32 MB
256 MB
2 x 32 MB
2 x 64 MB
2 x 32 MB
256 MB
2 x 32 MB
2 x 16 MB
2 x 32 MB
512 MB
2 x 128 MB
512 MB
2 x 32 MB
Bank 4
Bank 5
Bank 6
2 x 16 MB
2 x 16 MB
2 x 16 MB
2 x 32 MB
2 x 32 MB
2 x 32 MB
2 x 32 MB
2 x 32 MB
2 x 128 MB
2 x 64 MB
2 x 64 MB
Table 2-3
Examples of DIMM Upgrade Combinations Compaq ProLiant 1200
Total Memory
Bank 1
Bank 2
Bank 3
Bank 4
32 MB
2 x 16 MB
64 MB
2 x 16 MB
64 MB
2 x 32 MB
128 MB
2 x 16 MB
2 x 16 MB
2 x 16 MB
2 x 16 MB
128 MB
2 x 32 MB
2 x 32 MB
128 MB
2 x 64 MB
128 MB
2 x 16 MB
2 x 16 MB
2 x 32 MB
2 x 16 MB
256MB
2 x 16 MB
2 x 16 MB
2 x 32 MB
2 x 64 MB
256 MB
2 x 32 MB
2 x 32 MB
2 x 32 MB
2 x 32 MB
256 MB
2 x 32 MB
2 x 32 MB
2 x 64 MB
256 MB
2 x 64 MB
2 x 64 MB
256 MB
2 x 128 MB
512 MB
2 x 64 MB
2 x 64 MB
2 x 64 MB
512 MB
2 x 64 MB
2 x 64 MB
2 x 128 MB
512 MB
2 x 128 MB
2 x 128 MB
2 x 64 MB
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-34
Removal and Replacement Procedures
Power Supply
To remove the power supply:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the left side access panel. See page 2-8.
3.
Remove the processor cage. See page 2-21.
4.
(Compaq ProLiant 1600 only) Slide the hot-plug drive cage out slightly ➊.
5.
(Compaq ProLiant 1600 only) Remove the processor baffle by detaching the velcro
holding it to the power supply.
6.
(Compaq ProLiant 1600 only) Disconnect the power supply cable from the power
switch.
7.
Disconnect all other power supply cables.
8.
Remove four T-15 screws securing the power supply to the back of the chassis ➋.
9.
Pull the power supply out the side of the chassis ➌.
1
3
2
Figure 2-31. Removing the Power Supply
Reverse steps 1 through 9 to replace the power supply.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-35
Backplane Board
The Compaq ProLiant 1600 backplane board has two SCSI connectors. The Compaq
ProLiant 1200 backplane board has one SCSI connector
To remove the backplane board:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the top cover. See page 2-9.
3.
Remove the left side access panel. See page 2-8.
4.
Remove the system I/O board cage. See page 2-17.
5.
Remove the processor cage. See page 2-21.
6.
Disconnect all cables from the backplane board.
7.
Remove the three T-15 screws from the backplane board.
8.
Slide the backplane board down slightly and pull it from its mounting posts.
Figure 2-32. Removing the Backplane Board
Reverse steps 1 through 8 to replace the backplane board.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
2-36
Removal and Replacement Procedures
External Replacement Battery
CAUTION: Do not remove the lithium battery from the
system I/O board or permanent damage may occur. If the
battery fails, use the external replacement battery.
To install the external replacement battery:
1.
Perform the preparation procedures. See page 2-2.
2.
Remove the top cover. See page 2-9.
3.
Connect the replacement battery to the battery header on the system I/O board.
4.
Move the jumper on connector E2 from pins 1 and 2 to pins 2 and 3.
Figure 2-33. Installing the External Replacement Battery
5. Remove the adhesive backing from the hook-and-loop fastener strip. Place the
battery and the hook-and-loop fastener strip as indicated in the following illustration.
6. Place the sticker included with your battery kit on the back of your server above the
power connector.
7. Run the System Configuration utility to reconfigure the server.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-1
Chapter 3
Diagnostic Tools
This chapter describes software and firmware diagnostic tools available for Compaq server
products. The sections in this chapter are:
■
Utility Access
■
Power-On Self-Test (POST)
■
Diagnostics Software
■
Drive Array Advanced Diagnostics (DAAD)
■
Integrated Management Log
■
Rapid Recovery Services
■
Remote Service Features
■
ROMPaq
■
Compaq Insight Manager
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-2 Diagnostic Tools
Utility Access
The Compaq SmartStart and Support Software CD contains the SmartStart program and
many of the Compaq utilities needed to maintain your system, including:
■
System Configuration Utility
■
Array Configuration Utility
■
Drive Array Advanced Diagnostics Utility
■
ROMPaq Firmware Upgrade Utilities
CAUTION: Do not select the Erase Utility when running the
SmartStart and Support Software CD. This will result in data
loss to the entire system.
There are several ways to access these utilities:
■
Run the Utilities on the system partition.
If the system was installed using SmartStart, the Compaq utilities are automatically
available on the system partition. The system partition could also have been created
during a manual system installation.
To run the utilities on the system partition, boot the system and press F10 when you
see the following message: “Press F10 for system partition utilities.” Then select the
utilities from the menu.
❏
System Configuration Utility is available under System Configuration menu.
❏
Array Configuration Utility is available under the System Configuration menu.
❏
Drive Array Advanced Diagnostics Utility is available under the Diagnostics
and Utilities menu.
❏
ROMPaq Firmware Upgrade Utility is available under the Diagnostics and
Utilities menu.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-3
■
Run the Utilities from diskette.
You can run the utilities from their individual diskettes. If you have a utility diskette
newer than the version on the SmartStart and Support Software CD, use that
diskette.
You can also create a diskette version of the utility from the SmartStart and Support
Software CD. To create diskette versions of the utilities from the CD:
■
1.
Boot the Compaq SmartStart and Support Software CD.
2.
From the Compaq System Utilities screen, select Create Support Software and
select Next.
3.
Select the diskette you would like to create from the list and follow the
instructions on the screen.
Run the Utilities from the Compaq SmartStart and Support Software CD.
IMPORTANT: Only the System Configuration Utility and the Array
Configuration Utility can be executed from the Compaq
SmartStart and Support Software CD. All other utilities can be
executed only from the system partition or from diskette.
To run these utilities directly from the Compaq SmartStart and Support Software CD:
1.
Boot the Compaq SmartStart and Support Software CD.
2.
From the Compaq System Utilities screen, select the utility you wish to run and
select Next.
❏
To execute the System Configuration Utility, select Run System
Configuration Utility.
❏
To execute the Array Configuration Utility, select Run Array
Configuration Utility.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-4 Diagnostic Tools
Power-On Self-Test (POST)
POST is a series of diagnostic tests that runs automatically on Compaq computers when the
system is turned on. POST checks the following assemblies to ensure that the computer
system is functioning properly:
■
Keyboard
■
Power supply
■
System board
■
Memory
■
Memory expansion boards
■
Controllers
■
Diskette drives
■
Hard drives
If POST finds an error in the system, an error condition is indicated by an audible and/or
visual message. If an error code is displayed on the screen during POST or after resetting
the system, follow the instructions in Table 3-1. The error messages and codes listed in
Table 3-1 include all codes generated by Compaq products. Your system generates only
those codes that are applicable to your configuration and options.
Table 3-1
POST Error Messages
Error Code
Audible
Beeps
L=Long
S=Short
Probable Source of
Problem
Action
A Critical Error
occurred prior
to this powerup
None
A catastrophic system
error, which caused
the server to crash,
has been logged.
Run Diagnostics.
Replace failed
assembly as indicated.
101-ROM Error
1L,1S
System ROM
checksum.
Run Diagnostics.
Replace failed
assembly as indicated.
101-I/O ROM
Error
None
Options ROM
checksum.
Run Diagnostics.
Replace failed
assembly as indicated.
102-System
Board Failure
None
DMA, timers, etc.
Replace the system
board. Run the
Compaq System
Configuration Utility.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-5
104-ASR-2
Timer Failure
None
System board failure.
Run Diagnostics.
Replace failed
assembly as indicated.
162-System
Options Not
Set
2S
Configuration
incorrect.
Run the System
Configuration Utility and
correct.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-6 Diagnostic Tools
POST Error Messages
Continued
Audible
Beeps
L=Long
S=Short
Error Code
Probable Source of
Problem
Action
163-Time &
Date Not Set
2S
Invalid time or date in
configuration
memory.
Run the System
Configuration Utility and
correct.
164-Memory
Size Error
2S
Configuration
memory incorrect.
Run the System
Configuration Utility and
correct.
170- Expansion
Device Not
Responding
None
EISA or PCI expansion
board failure.
Check board for secure
installation. Replace
the failed board if
necessary.
172Configuration
Nonvolatile
Memory
Invalid
None
Nonvolatile
configuration corrupt
or jumper installed.
Run the System
Configuration Utility and
correct.
172-1
Configuration
Nonvolatile
Memory
Invalid
None
Nonvolatile
configuration corrupt.
Run the System
Configuration Utility and
correct.
173- Slot ID
Mismatch
None
Board replaced,
configuration not
updated.
Run the System
Configuration Utility and
correct.
174Configuration/
Slot Mismatch
Device Not
Found
None
EISA or PCI board not
found.
Run the System
Configuration Utility and
correct.
175Configuration/
Slot Mismatch
Device Found
None
EISA or PCI board
added, configuration
not updated.
Run the System
Configuration Utility and
correct.
176-Slot with
Not Readable
ID Yields
Valid ID
None
EISA or PCI board in
slot that should
contain an ISA board.
Run the System
Configuration Utility and
correct.
177Configuration
Not Complete
None
Incomplete System
Configuration.
Run the System
Configuration Utility and
correct.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-7
178-Processor
Configuration
Invalid
None
Processor type or step
does not match
configuration
memory.
Run the System
Configuration Utility and
correct.
179-System
Revision
Mismatch
None
A board was installed
that has a different
revision date.
Run the System
Configuration Utility and
correct.
180-Log
Reinitialized
None
201-Memory
Error
None
RAM failure.
Run Diagnostics.
Replace failed
assembly as indicated.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-8 Diagnostic Tools
POST Error Messages
Continued
Audible
Beeps
L=Long
S=Short
Error Code
Probable Source of
Problem
Action
203-Memory
Address Error
None
RAM failure.
Run Diagnostics.
Replace failed
assembly as indicated.
205-Cache
Memory Error
None
Cache memory error.
Replace the processor
board in the slot
indicated.
205-Option
Cache
Memory Error
None
Option cache
memory error.
Replace the option
cache board.
206-Cache
Controller Error
None
Cache controller
failure.
Run Diagnostics.
Replace failed
assembly as indicated.
207-Invalid
Memory
Configuration Check DIMM
[SIMM]
Installation
None
Memory module
installed incorrectly.
Verify placement of
memory modules.
208-Invalid
Memory
Speed - Check
DIMM [SIMM]
Installation
1L, 1S
The speed of the
memory is too slow,
where:
xx00 = expansion
board SIMMs are too
slow, or
00yy = system board
SIMMs are too slow.
xx and yy have
corresponding bit set.
The speed of the
memory modules must
be 60 ns. Verify the
speed of the memory
modules installed and
replace.
211-Cache
Switch Set
Incorrectly
None
Switch not set
properly during
installation or
upgrade.
Verify switch settings.
212-System
Processor
Failed/Mappe
d out
1S
Processor in slot x
failed.
Run Diagnostics and
replace failed
processor.
213-Cache
Size Error
None
Invalid optional
cache size.
Replace cache with
256K cache.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-9
213-System
Processor Not
Installed
1S
System processor
configured for slot
indicated is missing.
Install processor in the
slot indicated or run the
System Configuration
Utility to remove the
processor from the
.CFG file.
214-DC-DC
Converter
Failed
None
PowerSafe Module
(DC-DC Converter)
failed.
Run Diagnostics.
Replace failed
assembly as indicated.
301-Keyboard
Error
None
Keyboard failure.
Turn off the computer,
then reconnect the
keyboard.
301-Keyboard
Error or Test
Fixture Installed
None
Keyboard failure.
Replace the keyboard.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-10 Diagnostic Tools
POST Error Messages
Continued
Audible
Beeps
L=Long
S=Short
Error Code
Probable Source of
Problem
Action
ZZ-301Keyboard Error
None
Keyboard failure. (ZZ
represents the
Keyboard Scan
Code.)
1. A key is stuck. Try to
free it.
2. Replace the
keyboard.
303-Keyboard
Controller Error
None
System board,
keyboard, or mouse
controller failure.
1. Run Diagnostics.
2. Replace failed
assembly as
indicated.
304-Keyboard
or System Unit
Error
None
Keyboard, keyboard
cable, or system
board failure.
1. Make sure the
keyboard is
attached.
2. Run Diagnostics to
determine which is in
error.
3. Replace the part
indicated.
40X-Parallel
Port X Address
Assignment
Conflict
2S
Both external and
internal ports are
assigned to parallel
port X.
Run the System
Configuration Utility and
correct.
402Monochrome
Adapter
Failure
1L, 2S
Monochrome display
controller.
Replace the
monochrome display
controller.
501-Display
Adapter
Failure
1L, 2S
Video display
controller.
Replace the video
board.
601-Diskette
Controller Error
None
Diskette controller
circuitry failure.
1. Make sure the
diskette drive cables
are attached.
2. Replace the diskette
drive and/or cable.
3. Replace the system
board.
605-Diskette
Drive
Type Error
2S
Mismatch in drive
type.
Run the System
Configuration Utility to
set diskette type
correctly.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-11
702-A
coprocessor
has been
detected that
was not
reported by
CMOS
None
Installed coprocessor
not configured.
Run the System
Configuration Utility and
correct.
703-CMOS
reports a
coprocessor
that has not
been
detected
2S
Coprocessor or
configuration error.
1. Run the System
Configuration Utility
and correct.
2. Replace the
coprocessor.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-12 Diagnostic Tools
POST Error Messages
Continued
Audible
Beeps
L=Long
S=Short
Error Code
Probable Source of
Problem
Action
1151-Com Port
1 Address
Assignment
Conflict
2S
Both external and
internal serial ports
are assigned to
COM1.
Run the System
Configuration Utility and
correct.
1152-Com Port
2, 3, or 4
Address
Assignment
Conflict
2S
Both external and
internal serial ports
are assigned to
COM2, COM3 or
COM4.
Run the System
Configuration Utility and
correct.
1600-Server
Manager/R
Failure
None
Server Manager/R
board failure. Error
code displays after
error message.
Run Diagnostics.
Replace failed
assembly as indicated.
1610Temperature
violation
detected.
Waiting for
system
to cool
2S
Ambient system
temperature too hot.
Check fan in system
environment.
1611-Fan
failure
detected
2S
Required fan not
installed or spinning.
Check fans.
1612-Primary
power supply
failure
2S
Primary power supply
has failed.
Replace power supply
as soon as possible.
1613-Low
System Battery
None
Real time clock
system battery is
running low on
power.
Run Diagnostics.
Replace failed
assembly as indicated.
1614Redundant fan
failure
detected
None
1701-SCSI
Controller
failure
None
A test on the Fast
SCSI-2 Controller
failed.
Run Diagnostics.
Replace failed
assembly as indicated.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-13
1702-SCSI
cable error
detected.
System halted.
None
Incorrect cabling.
1. For integrated SCSI
Controllers, ensure
that the internal
connector has SCSI
termination
attached.
2. For option card SCSI
controllers, ensure
that only one of the
two internal
connectors has
termination
attached.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-14 Diagnostic Tools
POST Error Messages
Error Code
Continued
Audible
Beeps
L=Long
S=Short
Probable Source of
Problem
Action
1703-SCSI
cable error
detected.
Internal SCSI
cable not
attached to
system board
connector.
System halted.
None
Incorrect cabling.
Ensure that the
integrated SCSI
controller has SCSI
termination attached.
1704Unsupported
Virtual Mode
Disk Operation.
DOS Driver
Required.
System halted.
None
System attempted to
perform a virtual
mode disk operation
without virtual mode
memory services.
Use fixed-disk device
driver that supports
virtual mode memory
services.
1705-Locked
SCSI Bus
Detected.
System halted.
None
SCSI bus failure.
Run Diagnostics.
Replace failed
assembly as indicated.
1730-Fixed Disk
0 does not
support DMA
Mode.
None
Fixed disk drive error.
Run the System
Configuration Utility and
correct.
1731-Fixed Disk
1 does not
support DMA
Mode.
None
Fixed disk drive error.
Run the System
Configuration Utility and
correct.
1740-Fixed Disk
0 failed Set
Block Mode
command
None
Fixed disk drive error.
Run the System
Configuration Utility and
correct.
1741-Fixed Disk
1 failed Set
Block Mode
command
None
Fixed disk drive error.
Run the System
Configuration Utility and
correct.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-15
1750-Fixed Disk
0 failed
Identify
command
None
Fixed disk drive error.
Run the System
Configuration Utility and
correct.
1751-Fixed Disk
1 failed
Identify
command
None
Fixed disk drive error.
Run the System
Configuration Utility and
correct.
1760-Fixed Disk
0 does not
support Block
Mode
None
Fixed disk drive error.
Run the System
Configuration Utility and
correct.
1761-Fixed Disk
1 does not
support Block
Mode
None
Fixed disk drive error.
Run the System
Configuration Utility and
correct.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-16 Diagnostic Tools
POST Error Messages
Error Code
Continued
Audible
Beeps
L=Long
S=Short
Probable Source of
Problem
Action
1764-Slot x Drive Array - Capacity Expansion Process is
temporarily disabled (followed by one of the following):
Expansion will resume when Array Accelerator has been
reattached.
Expansion will resume when Array Accelerator has been
replaced.
Expansion will resume when Array Accelerator RAM
allocation is successful.
Expansion will resume when Array Accelerator battery
reaches full charge.
Expansion will resume when automatic data recovery
has been completed.
Reattach or replace
Array Accelerator, wait
until the Array
Accelerator batteries
have charged, or for
Automatic Data
Recovery to complete,
as indicated.
1765-Slot x Drive Array Option ROM Appears to Conflict
With an ISA Card. ISA cards with 16-bit memory cannot
be configured in memory range C0000 to DFFFF along
with the SMART-2/E 8-bit Option ROM due to EISA bus
limitations. Please remove or reconfigure your ISA card.
Remove or reconfigure
conflicting ISA cards.
Disable “ shared
memory” on any ISA
network cards that may
be installed.
1766-Slot x Drive Array requires System ROM Upgrade.
Run Systems ROMPaq Utility.
Run the latest Systems
ROMPaq Utility to
upgrade your System
ROMs.
1767-Slot x Drive Array Option ROM is Not Programmed
Correctly or may Conflict with the Memory Address
Range of an ISA Card. Check the Memory Address
Configuration of installed ISA Card(s) or run Options
ROMPaq Utility to attempt SMART-2/E Option ROM
Reprogramming.
Remove or reconfigure
conflicting ISA cards,
especially any cards
that are not recognized
by the System
Configuration Utility. Try
reprogramming the
SMART-2/E Controller’s
ROMs using the latest
Options ROMPaq
(version 2.29 or higher).
1768-Slot x
Drive Array Resuming
logical drive
expansion
process.
No action required.
Appears whenever a
controller reset or
power cycle occurs
while array expansion is
in progress.
None
SMART-2 Controller
error.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-17
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-18 Diagnostic Tools
POST Error Messages
Error Code
Continued
Audible
Beeps
L=Long
S=Short
Probable Source of
Problem
Action
1769-Slot x
Drive Array Drive(s)
disabled due
to failure
during
expand. Select
F1 to continue
with logical
drives
disabled.
Select F2 to
accept data
loss and to reenable logical
drives.
None
SMART-2 Controller
error.
Data has been lost
while expanding the
array, therefore the
drives have been
temporarily disabled.
Press F2 to accept the
data loss and re-enable
the logical drives.
Restore data from
backup.
1771-Primary
Disk Port
Address
Assignment
Conflict
None
Internal and external
hard drive controllers
are both assigned to
the primary address.
Run the System
Configuration Utility and
correct.
1772Secondary Disk
Port Address
Assignment
Conflict
None
Address Assignment
Conflict. Internal and
external hard drive
controllers are both
assigned to the
secondary address.
Run the System
Configuration Utility and
correct.
1773-Primary
Fixed Disk Port
Assignment
Conflict
None
Fixed disk drive error.
Run the System
Configuration Utility and
correct.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-19
1774-Slot x
Drive Array Obsolete data
found in Array
Accelerator.
Select F1 to
discard
contents of
Array
Accelerator.
Select F2 to
write contents
of Array
Accelerator to
drives.
None
SMART-2 Controller
error
Data found in Array
Accelerator is older
than data found on
drives. Press F1 to
discard the older data
in the Array Accelerator
and retain the newer
data on the drives.
1776-Drive
Array - SCSI
Port
Termination
Error
None
External and internal
SCSI drives are both
configured to Port 1.
Reconfigure drives.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-20 Diagnostic Tools
POST Error Messages
Error Code
Continued
Audible
Beeps
L=Long
S=Short
Probable Source of
Problem
Action
1777-Drive
Array External
Drive
Subsystem Error
None
Cooling fan failure,
internal temperature
alert or open side
panel.
Inspect for cooling fan
failure or open side
panel.
1778-Drive
Array resuming
Automatic
Data Recovery
process
None
This message appears
whenever a controller
reset or power cycle
occurs while
Automatic Data
Recovery is in
progress.
No action necessary.
1779-Drive
Array
Controller
detects
replacement
drives
None
Intermittent drive
failure and/or possible
loss of data.
If this message appears
and drive X has not
been replaced, this
indicates an
intermittent drive failure.
This message also
appears once
immediately following
drive replacement
whenever data must be
restored from backup.
1780-Disk 0
Failure
None
Hard drive/format
error.
Run Diagnostics.
Replace failed
assembly as indicated.
1781-Disk 1
Failure
None
Hard drive/format
error.
Run Diagnostics.
Replace failed
assembly as indicated.
1782-Disk
Controller
Failure
None
Hard disk drive
circuitry error.
Run Diagnostics.
Replace failed
assembly as indicated.
1784-Drive
Array Drive
Failure,
Physical Drive
None
Defective drive
and/or cables.
Check for loose cables.
Replace defective drive
X and/or cable(s).
1785-Drive
Array not
Configured
None
Configuration error.
Run the System
Configuration Utility and
correct.
Continued
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-21
POST Error Messages
Error Code
Continued
Audible
Beeps
L=Long
S=Short
Probable Source of
Problem
Action
1786-Drive Array
Recovery
Needed
The following
drive(s) need
Automatic Data
Recovery: Drive X.
Select "F1" to
continue with
recovery of data
to drive(s).
Select "F2" to
continue without
recovery of data
to drive(s).
None
Interim Data
Recovery
mode. Data has not
been recovered yet.
Press F1 key to allow
Automatic Data
Recovery to begin.
Data will automatically
be restored to drive X
now that the drive has
been replaced or now
seems to be working.
-OrPress the F2 key and
the system will
continue to operate in
the Interim Data
Recovery mode.
1787-Drive Array
Operating in
Interim Recovery
Mode.
Physical drive
replacement
needed: Drive X
None
Hard drive X failed or
cable is loose or
defective. Following
a system restart, this
message reminds
you that drive X is
defective and fault
tolerance is being
used.
1. Replace drive X as
soon as possible.
2. Check loose cables.
3. Replace defective
cables.
*1788-Incorrect
Drive Replaced:
Drive X Drive(s)
were incorrectly
replaced: Drive Y
Select "F1" to
continue - drive
array will remain
disabled.
Select "F2" to reset
configuration - all
data will be lost.
None
Drives are not
installed in their
original positions, so
the drives have
been disabled. See
note below.
Reinstall the drives
correctly as indicated.
Press F1 to restart the
computer with the
drive array disabled.
-OrPress F2 to use the
drives as configured
and lose all the data
on them.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-22 Diagnostic Tools
*NOTE: The 1788 error message might also be displayed inadvertently due to a bad
power cable connection to the drive or by noise on the data cable. If this
message was due to a bad power cable connection, but not because of an
incorrect drive replacement, repair the connection and press F2.
-OrIf this message was not due to a bad power cable connection, and no drive
replacement took place, this could indicate noise on the data cable. Check
cable for proper routing.
Continued
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-23
POST Error Messages
Error Code
Continued
Audible
Beeps
L=Long
S=Short
Probable Source of
Problem
Action
1789-Drive Not
Responding,
Physical Drive
Check cables
or replace
physical drive
X.
Select "F1" to
continue drive array will
remain
disabled.
Select "F2" to
fail drive(s)
that are not
responding Interim
Recovery
Mode will be
enabled if
configured for
fault
tolerance.
None
Cable or hard drive
failure.
1. Check the cable
connections.
2. If cables are
connected, replace
the drive.
3. If you do not want to
replace the drives
now, press F2.
1790-Disk 0
Configuration
Error
None
Hard drive error or
wrong drive type.
Run the System
Configuration Utility and
Diagnostics and
correct.
1791-Disk 1
Error
None
Hard drive error or
wrong drive type.
Run the System
Configuration Utility and
Diagnostics and
correct.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-24 Diagnostic Tools
1792-Drive
Array Reports
Valid Data
Found in Array
Accelerator.
Data will
automatically
be written to
drive array.
None
This indicates that
while the system was
in use, power was
interrupted while
data was in the Array
Accelerator memory.
Power was then
restored within eight
to ten days, and the
data in the Array
Accelerator was
flushed to the drive
array.
No action necessary; no
data has been lost.
Perform orderly system
shutdowns to avoid
data remaining in the
Array Accelerator.
Continued
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-25
POST Error Messages
Error Code
Continued
Audible
Beeps
L=Long
S=Short
Probable Source of
Problem
Action
1793-Drive
Array - Array
Accelerator
Battery
Depleted Data Lost
(Error message
1794 also
displays.)
None
This indicates that
while the system was
in use, power was
interrupted while
data was in the Array
Accelerator memory.
Array Accelerator
batteries failed. Data
in Array Accelerator
has been lost.
Power was not restored
within eight to ten days.
Perform orderly system
shutdowns to avoid
data remaining in the
Array Accelerator.
1794-Drive
Array - Array
Accelerator
Battery
Charge Low.
Array
Accelerator is
temporarily
disabled.
Array
Accelerator
will be reenabled when
battery
reaches full
charge.
None
This is a warning that
the battery charge is
below 75%. Posted
writes are disabled.
Replace the Array
Accelerator board if
batteries do not
recharge within 36
power-on hours.
1795-Drive
Array - Array
Accelerator
Configuration
Error.
Data does not
correspond to
this drive array.
Array
Accelerator is
temporarily
disabled.
None
This indicates that
while the system was
in use, power was
interrupted while
data was in the Array
Accelerator memory.
The data stored in the
Array Accelerator
does not correspond
to this drive array.
Match the Array
Accelerator to the
correct drive array, or
run the System
Configuration Utility to
clear the data in the
Array Accelerator.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-26 Diagnostic Tools
1796-Drive
Array - Array
Accelerator
Not
Responding.
Array
Accelerator is
temporarily
disabled.
None
Array Accelerator is
defective or has
been removed.
1. Check that the Array
Accelerator is
properly seated.
2. Run the System
Configuration Utility
to reconfigure the
Compaq IDA-2
without the Array
Accelerator.
Continued
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-27
POST Error Messages
Error Code
Continued
Audible
Beeps
L=Long
S=Short
Probable Source of
Problem
Action
1797-Drive
Array - Array
Accelerator
Read Error
Occurred.
Data in Array
Accelerator
has been lost.
Array
Accelerator is
disabled.
None
Hard parity error while
reading data from
posted writes
memory.
Enable Array
Accelerator.
1798-Drive
Array - Array
Accelerator
Write Error
Occurred.
Array
Accelerator is
disabled.
None
Hard parity error while
writing data to posted
writes memory.
Enable Array
Accelerator.
1799-Drive
Array - Drive(s)
Disabled due
to Array
Accelerator
Data Loss.
Select "F1" to
continue with
logical drives
disabled.
Select "F2" to
accept data
loss and to reenable logical
drives.
None
Volume failed due to
loss of data in postedwrites memory.
Press F1 to continue
with logical drives
disabled or F2 to
accept data loss and
re-enable logical drive.
Beeps only: 2
Long + 2 Short
2L, 2S
Power is cycled.
Temperature too hot.
Processor fan not
installed or spinning.
Check fans.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-28 Diagnostic Tools
(Run System
Configuration
Utility - F10 key)
None
A configuration error
occurred during POST.
Press F10 to run System
Configuration Utility.
(RESUME - F1
KEY)
None
As indicated to
continue.
Press the F1 key.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-29
Diagnostics Software
The error messages and codes listed in Table 3-2 include all codes generated by Compaq
products. Your system generates only those codes that are applicable to your configuration
and options.
When you select Diagnostics and Utilities from the System Configuration Utility main
menu, the utility prompts you to test, inspect, upgrade, and diagnose the server.
Diagnostics and Utilities are located on the system partition on the hard drive and must be
accessed when a system configuration error is detected during the Power-On Self-Test
(POST). Compaq Diagnostics software is also available on the Compaq SmartStart and
Support Software CD. You can create a Diagnostics diskette from the SmartStart CD, and
run Diagnostics from diskette.
The following options are available from the Diagnostics and Utilities menu:
■
Test Computer
■
Inspect Computer
■
Upgrade Firmware
■
Remote Utilities
■
Diagnose Drive Array
Diagnostic error codes are generated when the Diagnostics software recognizes a problem.
These error codes help identify possible defective subassemblies. Tables 3-2 through 3-17
list possible error codes, a description of the error condition, and the action required to
resolve the error condition.
In each case, the Recommended Action column lists the steps necessary to correct the
problem. After completing each step, run the Diagnostics program to verify whether the
error condition has been corrected. If the error code reappears, perform the next step, then
run the Diagnostics program again. Follow this procedure until the Diagnostics program no
longer detects an error condition.
If you encounter an error condition, complete the following steps before starting problem
isolation procedures:
1. Be sure that there is proper ventilation. The computer should have approximately
12 inches (30.5 cm) clearance at the front and back of the system unit.
2. Turn off the computer and peripheral devices.
3. Disconnect any peripheral devices not required for testing. Do not disconnect the
printer if you want to test it or use it to log error messages.
4. Turn on the computer.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-30 Diagnostic Tools
5. Delete the power-on password, if set. You will know that the power-on password is
set when a key icon appears on the screen when POST completes. If this occurs, you
must enter the password to continue. To delete the password, type the current
password, a forward slash ( / ), and press the Enter key.
6. If you do not have access to the password, you must disable the power-on password
by using the Password Disable switch on the system board.
7. When required by Diagnostics, install a loopback plug (Part Number 142054-001).
8. Run the latest version of Diagnostics.
Primary Processor Test Error Codes
The 100 series of Diagnostic error codes identifies failures with processor and system
board functions. Corrective action may require replacement of system boards or processor
assemblies (either processor boards or system boards that include the processor).
Table 3-2
Primary Processor Test Error Codes
Error Code
Description
Recommended Action
101-xx
CPU test failed.
Replace the processor board and
retest.
103-xx
104-xx
105-xx
106-xx
DMA page registers test failed.
Interrupt controller master test
failed.
Port 61 error.
Keyboard controller self-test failed.
For error codes 103-xx through
106-xx, replace the processor
board and retest.
107-xx
108-xx
109-xx
CMOS RAM test failed.
CMOS interrupt test failed.
CMOS clock load data test failed.
The following steps apply to error
codes 107-xx through 109-xx.
1. Replace the battery/clock
module and retest.
2. Replace the system board and
retest.
110-xx
111-xx
112-xx
113-xx
Programmable timer load data test For error codes 110-xx through
failed.
113-xx, replace the system board
and retest.
Refresh detect test failed.
Speed test slow mode out of range.
Protected mode test failed.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-31
114-xx
Speaker test failed.
1. Verify the speaker connection
and retest.
2. Replace the speaker and
retest.
3. Replace the system board and
retest.
116-xx
Cache test failed.
Replace the system board and
retest.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-32 Diagnostic Tools
Primary Processor Test Error Codes
Error Code
122-xx
123-xx
Continued
Description
Recommended Action
Multiprocessor Dispatch test failed. 1. Check the system configuration
Interprocessor Communication test
and
failed.
retest.
2. Replace the processor board
and retest.
3. Replace the system board and
retest.
199-xx
Installed devices test failed.
1. Check the system configuration
and retest.
2. Verify cable connections and
retest.
3. Check switch and/or jumper
settings and retest.
4. Run the Configuration utility
and retest.
5. Replace the processor board
and retest.
6. Replace the system board and
retest.
Memory Test Error Codes
The 200 series of Diagnostic error codes identifies failures with the memory subsystem.
Corrective action may require replacement of the memory expansion board, the memory
modules, or the processor assembly.
Table 3-3
Memory Test Error Codes
Error Code
Description
Recommended Action
200-xx
Invalid memory configuration.
Reinsert memory modules in
correct location and retest.
201-xx
202-xx
Memory machine ID test failed.
Memory system ROM checksum
failed.
The following steps apply to error
codes 201-xx and 202-xx:
1. Replace the system ROM and
retest.
2. Replace the processor board
and retest.
3. Replace the memory
expansion board and retest.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-33
203-xx
204-xx
205-xx
206-xx
Memory write/read test failed.
Memory address test failed.
Walking I/O test failed.
Increment pattern test failed.
The following steps apply to error
codes 203-xx through 210-xx:
1. Replace the memory module
and retest.
2. Replace the processor board
and retest.
3. Replace the memory
expansion board
and retest.
207-xx
Invalid memory configuration-check Replace DIMMs.
DIMM installation. DIMMs installed
have 8K refresh.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-34 Diagnostic Tools
Memory Test Error Codes
Error Code
Continued
Description
Recommended Action
208-xx
Invalid memory speed detected Replace DIMMs with timing
check DIMM installation. Slow DIMMs greater than
may cause data loss.
60 ns.
210-xx
Random pattern test failed.
The following steps apply to error
code
210-xx:
1. Replace the memory module
and retest.
2. Replace the processor board
and retest.
3. Replace the memory
expansion board and retest.
215
Non-functioning DC-DC converter
for
processor X.
Replace the DC-DC converter
(processor power module).
Keyboard Test Error Codes
The 300 series of Diagnostic error codes identifies failures with keyboard and system board
functions. Corrective action may require replacement of the keyboard or the system board
assembly.
Table 3-4
Keyboard Test Error Codes
Error Code
301-xx
302-xx
303-xx
304-xx
Description
Keyboard short test, 8042 self-test
failed.
Keyboard long test failed.
Keyboard LED test, 8042 self-test
failed.
Keyboard typematic test failed.
Recommended Action
The following steps apply to error
codes 301-xx through 304-xx:
1. Check the keyboard
connection. If disconnected,
turn off the computer and
connect the keyboard and
retest.
2. Replace the keyboard and
retest.
3. Replace the system board and
retest.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-35
Parallel Printer Test Error Codes
The 400 series of Diagnostic error codes identifies failures with parallel printer interface
card or system board functions. Corrective action may require replacement of the
serial/parallel interface board or the system board assembly.
Table 3-5
Parallel Printer Test Error Codes
Error Code
401-xx
402-xx
403-xx
498-xx
Description
Printer failed or not connected.
Printer data register failed.
Printer pattern test failed.
Printer failed or not connected.
Recommended Action
The following steps apply to error
codes 401-xx through 498-xx:
1. Connect the printer and retest.
2. Check the power to the printer
and retest.
3. Install the loopback connector
and retest.
4. Check the switch on the
Serial/Parallel Interface board
(if applicable) and retest.
5. Replace the Serial/Parallel
Interface board (if applicable)
and retest.
6. Replace the system board and
retest.
Video Display Unit Test Error Codes
The 500 series of Diagnostic error codes identifies failures with video or system board
functions. Corrective action may require replacement of the video board or the system
board assembly.
Table 3-6
Video Display Unit Test Error Codes
Error Code
Description
Recommended Action
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-36 Diagnostic Tools
501-xx
502-xx
503-xx
504-xx
505-xx
506-xx
507-xx
508-xx
509-xx
510-xx
511-xx
512-xx
514-xx
516-xx
Video controller test failed.
Video memory test failed.
Video attribute test failed.
Video character set test failed.
Video 80 x 25 mode 9 x 14 character cell
test failed.
Video 80 x 25 mode 8 x 8 character cell test
failed.
Video 40 x 25 mode test failed.
Video 320 x 200 mode color set 0 test failed.
Video 320 x 200 mode color set 1 test failed.
Video 640 x 200 mode test failed.
Video screen memory page test failed.
Video gray scale test failed.
Video white screen test failed.
Video noise pattern test failed.
The following steps apply to
error codes 501-xx through
516-xx:
1. Replace the monitor and
retest.
2. Replace the Advanced
VGA board and retest.
3. Replace the system
board and retest.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-37
Diskette Drive Test Error Codes
The 600 series of Diagnostic error codes identifies failures with diskette, diskette drive, or
system board functions. Corrective action may require replacement of the diskette, the
diskette drive, or the system board assembly.
Table 3-7
Diskette Drive Test Error Codes
Error Code
Description
Recommended Action
600-xx
601-xx
602-xx
603-xx
604-xx
605-xx
606-xx
607-xx
608-xx
609-xx
610-xx
694-xx
697-xx
698-xx
Diskette ID drive types test failed.
Diskette format failed.
Diskette read test failed.
Diskette write/read/compute test
failed.
Diskette random seek test failed.
Diskette ID media failed.
Diskette speed test failed.
Diskette wrap test failed.
Diskette write protect test failed.
Diskette reset controller test failed.
Diskette change line test failed.
Pin 34 is not cut on 360 KB diskette
drive.
Diskette type error.
Diskette drive speed not within limits.
The following steps apply to error
codes 600-xx through 698-xx:
1. Replace the diskette and
retest.
2. Check and/or replace the
diskette power and signal
cables and retest.
3. Replace the diskette drive
and retest.
4. Replace the system board
and retest.
699-xx
Diskette drive/media ID error.
The following steps apply to 699xx error codes:
1. Replace the media and
retest.
2. Run the Configuration utility
and retest.
Monochrome Video Board Test Error Codes
The 800 series of Diagnostic error codes identifies failures with monochrome video boards
or system board functions. Corrective action may require replacement of a monochrome
video board or the system board assembly.
Table 3-8
Monochrome Video Board Test Error Codes
Error Code
Description
Recommended Action
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-38 Diagnostic Tools
802-xx
824-xx
Video memory test failed. The following steps apply to error codes 802-xx
Monochrome video text and 824-xx:
mode
1. Replace monitor and retest.
test failed.
2. Replace the Advanced VGA board and
retest.
3. Replace monochrome board and retest.
4. Replace the system board and retest.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-39
Serial Test Error Codes
The 1100 series of Diagnostic error codes identifies failures with serial/parallel interface
board or system board functions. Corrective action may require replacement of the
serial/parallel interface board or the system board assembly.
Table 3-9
Serial Test Error Codes
Error Code
1101-xx
1109-xx
Description
Serial port test failed.
Clock register test failed.
Recommended Action
The following steps apply to error
codes 1101-xx and 1109-xx:
1. Check the switch settings on
the Serial/Parallel Interface
board (if applicable) and
retest.
2. Replace the Serial/Parallel
Interface board (if applicable)
and retest.
3. Replace the system board
and retest.
Modem Communications Test Error Codes
The 1200 series of Diagnostic error codes identifies failures with the modem. Corrective
action may require replacement of the modem.
Table 3-10
Modem Communications Test Error Codes
Error Code
1201-xx
1202-xx
1203-xx
1204-xx
1206-xx
1210-xx
Description
Recommended Action
Modem internal loopback test failed. The following steps apply to error
Modem time-out test failed.
codes 1201-xx through 1210-xx:
Modem external termination test failed. 1. Refer to the modem
Modem auto originate test failed.
documentation for correct
Dial multi-frequency tone test failed.
setup procedures and retest.
Modem direct connect test failed.
2. Check the modem line and
retest.
3. Replace the modem and
retest.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-40 Diagnostic Tools
Fixed Disk Drive Test Error Codes
The 1700 series of Diagnostic error codes identifies failures with fixed disk drives, fixed
disk drive controller boards, fixed disk drive cabling, and system board functions.
Corrective action may require replacement of the fixed disk drive cables, fixed disk drive
controller, fixed disk, or system board assembly. If your system uses a drive array
controller, see the section for Drive Array Advanced Diagnostics (DAAD).
Table 3-11
Fixed Disk Drive Test Error Codes
Error Code
1700-xx
1701-xx
1702-xx
1703-xx
1704-xx
1705-xx
1708-xx
1709-xx
1710-xx
1715-xx
1716-xx
1717-xx
1719-xx
1736-xx
1799-xx
Description
Recommended Action
Fixed disk ID drive types test failed. The following steps apply to error
Fixed disk format test failed.
codes 1700-xx through 1799-xx:
Fixed disk read test failed.
1. Run the System Configuration
Fixed disk write/read/compare test Utility and
failed.
verify the drive type.
Fixed disk random seek test failed. 2. Replace the fixed disk drive
Fixed disk controller test failed.
signal and power cables and
Fixed disk format bad track test
retest.
failed.
3. Replace the fixed disk drive
Fixed disk reset controller test failed. controller
Fixed disk park head test failed.
and retest.
Fixed disk head select test failed.
4. Replace the fixed disk drive and
Fixed disk conditional format test
retest.
failed.
5. Replace the system board and
Fixed disk ECC* test failed.
retest.
Fixed disk drive power mode test
failed.
Drive Monitoring failed.
Invalid fixed disk drive type failed.
* Error Checking and Correcting
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-41
Tape Drive Test Error Codes
The 1900 series of Diagnostic error codes identifies failures with tape cartridge, tape drive,
tape drive cabling, adapter board, or system board assembly. Corrective action may require
replacement of the tape cartridge, tape drive cabling, adapter board, tape drive, or system
board assembly.
Table 3-12
Tape Drive Test Error Codes
Error Code
1900-xx
1901-xx
1902-xx
1903-xx
1904-xx
1905-xx
1906-xx
Description
Tape ID failed.
Tape servo write failed.
Tape format failed.
Tape drive sensor test failed.
Tape BOT/EOT test failed.
Tape read test failed.
Tape write/read/compare test failed.
Recommended Action
The following steps apply to error
codes 1900-xx through 1906-xx:
1. Replace the tape cartridge
and retest.
2. Check and/or replace the
signal cable and retest.
3. Check the switch settings on
the adapter board (if
applicable).
4. Replace the tape adapter
board (if applicable) and
retest.
5. Replace the tape drive and
retest.
6. Replace the system board
and retest.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-42 Diagnostic Tools
Advanced VGA Board Test Error Codes
The 2400 series of Diagnostic error codes identifies failures with the video board, monitor,
or system board assembly. Corrective action may require replacement of the monitor, video
board, or system board assembly.
Table 3-13
Advanced VGA Board Test Error Codes
Error Code
Description
Recommended Action
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-43
2402-xx
2403-xx
2404-xx
2405-xx
2406-xx
2407-xx
2408-xx
2409-xx
2410-xx
2411-xx
2412-xx
2414-xx
2416-xx
2417-xx
2418-xx
2419-xx
2420-xx
2421-xx
2422-xx
2423-xx
2424-xx
2425-xx
2431-xx
2432-xx
2448-xx
2451-xx
2456-xx
Video memory test failed.
Video attribute test failed.
Video character set test failed.
Video 80 x 25 mode 9 x 14 character
cell
test failed.
Video 80 x 25 mode 8 x 8 character
cell
test failed.
Video 40 x 25 mode test failed.
Video 320 x 320 mode color set 0 test
failed.
Video 320 x 320 mode color set 1 test
failed.
Video 640 x 200 mode test failed.
Video screen memory page test
failed.
Video gray scale test failed.
Video white screen test failed.
Video noise pattern test failed.
Lightpen text mode test failed, no
response.
ECG/VGC memory test failed.
ECG/VGC ROM checksum test failed.
ECG/VGC attribute test failed.
ECG/VGC 640 x 200 graphics mode
test failed.
ECG/VGC 640 x 350 16-color set test
failed.
ECG/VGC 640 x 350 64-color test
failed.
ECG/VGC monochrome text mode
test failed.
ECG/VGC monochrome graphics
mode test failed.
640 x 480 graphics test failure.
320 x 200 graphics (256-color mode)
test failed.
Advanced VGA Controller test failed.
132-column Advanced VGA test
failed.
Advanced VGA 256-Color test failed.
The following steps apply to error
codes 2402-xx through 2456-xx:
1. Run the System Configuration
Utility.
2. Replace the monitor and
retest.
3. Replace the Advanced VGA
board or other video board
and retest.
4. Replace the system board
and retest.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-44 Diagnostic Tools
2458-xx
2468-xx
2477-xx
2480-xx
Advanced VGA Bit BLT Test
Advanced VGA DAC Test
Advanced VGA Data Path Test
Advanced VGA DAC Test
The following steps apply to error
codes 2458-xx through 2480-xx:
1. Run Setup.
2. Replace the system board
and retest.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-45
Compaq Network Interface Cards
Test Error Codes
The 6000 series of Diagnostic error codes identifies failures with
32-bit DualSpeed NetFlex-2/Token Ring Controllers. Corrective action may require
replacement of the 32-bit DualSpeed NetFlex-2/Token Ring Controller.
Table 3-14
Compaq Network Interface Cards
Test Error Codes
Error Code
6000-xx
6001-xx
6002-xx
6014-xx
6016-xx
6028-xx
6029-xx
6089-xx
6090-xx
6091-xx
6092-xx
Description
Recommended Action
The following steps apply to error
Network card ID failed.
codes 6000-xx through 6089-xx:
Network card setup failed.
Network card transmit failed.
1. Check the controller
installation in the EISA slot.
Network card configuration failed.
2. Check the interrupt type and
Network card reset failed.
Network card internal failed.
number setting.
3. Check the media connection
Network card external failed.
at the controller and
Network card open failed.
Network card initialization failed.
Multistation Access Unit
Network card Internal loopback failed.
(MAU)*.
Network card external loopback
4. Check the media speed
(4/16 ) and type Unshielded
failed.
Twisted Pair/Shielded Twisted
Pair (UTP/STP) settings.
5. Check the MAU, cabling, or
other network components.
6. Replace the controller.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-46 Diagnostic Tools
SCSI Fixed Disk Drive Test Error Codes
The 6500 series of Diagnostic error codes identifies failures with SCSI fixed disk drives,
SCSI fixed disk drive controller boards, SCSI fixed disk drive cabling, and system board
functions. Corrective action may require replacement of the fixed disk drive cables, fixed
disk drive controller, fixed disk, or system board assembly. If your system uses a drive
array controller, see the section for Drive Array Advanced Diagnostics (DAAD).
Table 3-15
SCSI Fixed Disk Drive Test Error Codes
Error Code
6500-xx
6502-xx
6505-xx
6506-xx
6509-xx
6523-xx
6528-xx
Description
Recommended Action
SCSI Disk ID drive types test failed.
SCSI Disk Unconditional Format test
failed.
SCSI Disk Read Test Failed.
SCSI Disk SA/Media test failed.
SCSI Disk Erase tape test failed.
SCSI Disk Random Read test failed.
Media load/unload test failed.
The following steps apply to error
codes 6500-xx through 6599-xx:
1. Run the System Configuration
Utility and verify the drive type.
2. Replace the SCSI disk drive
signal and power cables and
retest.
3. Replace the SCSI controller and
retest.
4. Replace the SCSI disk drive and
retest.
5. Replace the system board and
retest.
SCSI/IDE CD-ROM Drive Test Error Codes
The 6600 series of Diagnostic error codes identifies failures with the CD-ROM cabling,
CD-ROM drive, adapter board, or system board assembly. Corrective action may require
replacement of the CD-ROM cabling, CD-ROM drive, adapter board, or system
board assembly.
Table 3-16
SCSI/IDE CD-ROM Drive Test Error Codes
Error Code
Description
Recommended Action
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-47
6600-xx
6605-xx
CD-ROM ID failed.
CD-ROM Read failed.
The following steps apply to error
codes 6600-xx through 6605-xx:
1. Replace the CD-ROM media
and retest.
2. Check and/or replace the
signal cable and retest.
3. Check the switch settings on
the adapter board (if
applicable).
4. Replace the SCSI controller (if
applicable) and retest.
5. Replace the CD-ROM drive and
retest.
6. Replace the system board and
retest.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-48 Diagnostic Tools
SCSI Tape Drive Test Error Codes
The 6700 series of Diagnostic error codes identifies failures with tape cartridge, tape drive,
media changer, tape drive cabling, adapter board, or system board assembly. Corrective
action may require replacement of the tape cartridge, tape drive, media changer, tape drive
cabling, adapter board, or system board assembly.
Table 3-17
SCSI Tape Drive Test Error Codes
Error Code
6700-xx
6706-xx
6709-xx
6728-xx
Description
SCSI Tape ID drive types test failed.
SCSI Disk SA/Media test failed.
SCSI Disk Erase tape test failed.
Media load/unload test failed.
Recommended Action
The following steps apply to error
codes 6700-xx through 6799-xx:
1. Run the System Configuration
Utility and verify the drive
type.
2. Replace the SCSI Tape drive
signal and power cables and
retest.
3. Replace the SCSI controller
and retest.
4. Replace the SCSI Tape drive
and retest.
5. Replace the system board
and retest.
Server Manager/R Board Test Error Codes
The 7000 series of Diagnostic error codes identifies failures with the Server Manager/R
board. Corrective action may require replacement of the Server Manager/R board, the
Integrated 2400-baud modem, voice ROM, or battery on the Server Manager/R board.
Table 3-18
Server Manager/R Board Test Error Codes
Error Code
Description
Recommended Action
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-49
7000-11
7000-12
7000-13
7000-14
7000-15
7000-21
7000-22
7000-23
7000-24
Processor (80186 Timer)
Processor (80186 Registers)
Processor (Watch Dog Timer)
Processor (8570 RAM)
Processor (8570 RTC)
Memory
Memory Write/Read
Memory Address
Memory Refresh Alert
For error codes 7000-11 through
7000-46, replace the Server
Manager/R board and retest.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-50 Diagnostic Tools
Server Manager/R Board Test Error Codes Continued
Error Code
Description
Recommended Action
7000-25
7000-26
7000-27
7000-28
7000-33
7000-34
7000-35
7000-41
7000-42
7000-43
7000-44
7000-45
7000-46
Memory Increment Memory Random For error codes 7000-11 through
Data
7000-46, replace the Server
Manager/R board and retest.
Memory Disturb Address
Memory HBM
HBM IO
HBM BMIC
HBM Video
ser_int
ser_int
ser_ext
ser_ext
ser_ext_int
ser_ext_int
7000-51
7000-52
7000-53
7000-54
7000-55
7000-56
7000-57
mdm_int
mdm_int
mdm_ext
mdm_ext
mdm_ext_int
mdm_ext_int
mdm\c\analog
For error codes 7000-51 through
7000-57, replace the Server
Manager/R board Enhanced
2400-Baud Integrated Modem
and retest.
7000-61
7000-62
Voice/DTMF Internal Loopback
Voice/DTMF Internal Loopback
For 7000-61 and 7000-62 error
codes, replace the Server
Manager/R board Voice ROM.
7000-78
7000-79
Host ADC Measurements
Battery
For 7000-78 and 7000-79 error
codes, replace the Server
Manager/R board battery.
Pointing Device Interface Test Error Codes
The 8600 Diagnostic error codes identifies failures with the pointing device (mouse,
trackball, and so forth) or the system board assembly. Corrective action may require
replacement of the pointing device or the system board assembly.
Table 3-19
Pointing Device Interface Test Error Codes
Error Code
Description
Recommended Action
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-51
8601-xx
Pointing Device Interface test
failed.
The following steps apply for the
8601-xx error codes:
1. Replace with a working
pointing device and retest.
2. Replace the system board
and retest.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-52 Diagnostic Tools
Drive Array Advanced Diagnostics
(DAAD)
Drive Array Advanced Diagnostics (DAAD) is a DOS-based tool designed to run on all
Compaq products that contain a Compaq Drive Array Controller. The error messages and
codes listed include all codes generated by Compaq products. Your system generates only
codes applicable to your configuration and options. The two main functions of DAAD are
to collect all possible information about the array controllers in the system and to offer a
list of all detected problems.
NOTE: Refer to the Drive Array Advanced Diagnostics User Guide
for complete details and procedures about this diagnostic tool.
DAAD works by issuing multiple commands to the array controllers to determine if a
problem exists. This data can then be saved to a file and, in severe situations, sent to
Compaq for analysis. In most cases, DAAD provides enough information to initiate
problem resolution immediately.
NOTE: DAAD does not write to the drives or destroy data. It does
not change or remove configuration information.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-53
Starting DAAD
To start DAAD:
1.
Insert the DAAD diskette into drive A.
2.
Reboot the system - OR - if you are at the DOS prompt, enter the following:
A:DAAD
NOTE: To generate a DAAD report without starting the interactive
portion of the utility, enter the following at the DOS prompt:
DAAD filename
where filename is the name of the file or report.
3. A dialog box is displayed, indicating the version of DAAD installed. Press the Enter
(or ‘C’) key to continue, or press the Esc (or ‘E’) key to exit without continuing.
4.
If you continue, a Please Wait panel is displayed, indicating that DAAD is
identifying the system parameters.
DAAD gathers all the information it can from all of the array controllers in the
system. The time it takes to gather this information depends on the size of your
system.
A second Please Wait panel may be displayed to indicate that the utility is identifying
the ROM version of an array controller in the system.
CAUTION: Do not cycle the power; the utility must perform
low-level operations that, if interrupted, could cause the
controller to revert to a previous level of firmware if the
firmware was soft-upgraded.
When the information gathering process is complete, the main DAAD screen is displayed.
NOTE: To generate a DAAD report without starting the interactive
portion of the utility, enter the following at the DOS prompt:
DAAD filename
where filename is the name of the file or report.
Table 3-20 lists DAAD diagnostic messages in alphabetical order.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-54 Diagnostic Tools
Table 3-20
DAAD Diagnostic Messages
Message
Description
Recommended Action
Accelerator board
not detected
Array controller did not
detect a configured array
accelerator board.
Install array accelerator
board on array controller. If
an array accelerator board
is installed, check for proper
seating on the array
controller board. You may
need to run the System
Configuration Utility and
disable the array
accelerator board to get
this message off the screen.
Accelerator error
log
List of the last 32 parity errors
on transfers to or from
memory on the array
accelerator board. Displays
starting memory address,
transfer count, and operation
(read and write).
If there are many parity
errors, you may need to
replace the array
accelerator board.
Accelerator parity
read errors: n
Number of times that read
memory parity errors were
detected during transfers
from memory on array
accelerator board.
If there are many parity
errors, you may need to
replace the array
accelerator board.
Accelerator parity
write errors: n
Number of times that write
memory parity errors were
detected during transfers to
memory on the array
accelerator board.
If there are many parity
errors, you may need to
replace the array
accelerator board.
Accelerator status:
Permanently
disabled
Array accelerator board has
been permanently disabled. It
will remain disabled until it is
reinitialized using the System
Configuration Utility.
Check the Disable Code
field. Run the System
Configuration Utility to
reinitialize the array
accelerator board.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-55
Accelerator status:
Possible data loss
in cache
Possible data loss detected
during power-up due to all
batteries being below
sufficient voltage level and no
presence of the identification
signatures on the array
accelerator board.
There is no way to
determine if dirty or bad
data was in the cache and
is now lost.
Accelerator status:
Temporarily
disabled
Array accelerator board has
been temporarily disabled.
Check the Disable Code
field.
Accelerator status:
Unrecognized
status
A status returned from the
array accelerator board that
DAAD does not recognize.
Obtain the latest version of
DAAD.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-56 Diagnostic Tools
DAAD Diagnostic Messages
Message
Continued
Description
Recommended Action
Accelerator
status: Valid
data found at
reset
Valid data was found in posted
write memory at reinitialization.
Data will be flushed to disk.
Not an error or data loss
condition. No action needs
to be taken.
Accelerator
status: Warranty
alert
Catastrophic problem with
array accelerator board. Refer
to other messages on
Diagnostics screen for exact
meaning of this message.
Replace the array
accelerator board.
Adapter/NVRAM
ID mismatch
EISA nonvolatile RAM has an ID
for a different controller from
the one physically present in
the slot.
Run the System
Configuration Utility.
Battery pack X
below reference
voltage
Battery pack on the array
accelerator is below the
required voltage levels.
Allow enough time for
batteries to recharge (36
hours). If batteries have not
recharged after 36 hours,
replace the array
accelerator board.
Battery X not
fully charged
Battery is not fully charged.
If 75% of the batteries
present are fully charged,
the array accelerator is fully
operational. If more than
75% of the batteries are not
fully charged, allow 36 hours
to recharge them.
Board not
attached
Array controller configured for
use with array accelerator
board, but one is not attached.
Attach array accelerator
board to array controller.
NVRAM
configuration
present,
controller not
detected
EISA nonvolatile RAM has a
configuration for an array
controller but there is no board
in this slot. Either a board has
been removed from the system
or a board has been placed in
the wrong slot.
Place the array controller in
the proper slot or run the
System Configuration Utility
to reconfigure nonvolatile
RAM to reflect the removal
or new position.
Compatibility
port problem
detected
Compatibility port configured
for this IDA controller. When
DAAD was verifying this
interface, a serious problem
was detected.
A hardware problem has
occurred; replace the IDA
controller.
Configuration
DAAD detected that
Run the latest version of
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-57
signature is zero
nonvolatile RAM contains a
configuration signature that is
zero. Old versions of the System
Configuration Utility could
cause this.
System Configuration Utility
to configure the controller
and nonvolatile RAM.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-58 Diagnostic Tools
DAAD Diagnostic Messages
Message
Continued
Description
Recommended Action
Configuration
signature
mismatch
Array accelerator board
configured for a different array
controller board.
Configuration signature on
array accelerator board does
not match the one stored on
the array controller board.
To recognize the array
accelerator board, run the
System Configuration Utility.
Controller
communication
failure occurred
Controller communication
failure occurred.
DAAD was unable to
successfully issue
commands to the
controller in this slot.
Controller
detected. NVRAM
configuration not
present
EISA nonvolatile RAM does not
contain a configuration for this
controller.
Run the System
Configuration Utility to
configure the nonvolatile
RAM.
Controller firmware
needs upgrading
Controller firmware is below
the latest recommended
version.
Run Options ROMPaq to
upgrade the controller to
the latest firmware revision.
Controller firmware
needs upgrading
(DAAD Error 102)
Controller is correct, however,
IDA firmware version should be
greater than 1.26.
Obtain the latest firmware.
Controller is
located in special
“ video” slot
Controller is installed in slot for
special video control signals. If
controller is used in this slot,
LED indicators on front panel
may not function properly.
Install the controller in a
different slot and run the
System Configuration Utility
to configure the controller
and nonvolatile RAM.
Controller is not
configured
Controller is not configured. If
controller was previously
configured and you change
drive locations, there may be
a problem with placement of
the drives. DAAD examines
each physical drive and looks
for drives that have been
moved to a different drive
bay.
Look for messages
indicating which drives
have been moved. If none
appear and drive
swapping did not occur,
run the System
Configuration Utility to
configure the controller
and nonvolatile RAM. Do
not run the System
Configuration Utility if you
believe drive swapping has
occurred.
Controller needs
replacing (DAAD
Error 102)
IDA firmware is less than
version 0.96.
Replace the controller as
soon as possible.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-59
Controller needs
replacing (DAAD
Error 104)
The Intelligent Array Expansion
System firmware is less than
version 1.14.
Replace the controller as
soon as possible.
Controller
reported POST
error.
Error Code: x
The controller returned an
error from its internal Power-On
Self Tests.
Replace the controller.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-60 Diagnostic Tools
DAAD Diagnostic Messages
Message
Continued
Description
Recommended Action
Controller
restarted with a
signature of zero
DAAD did not find a valid
configuration signature to use
to get the data. Nonvolatile
RAM may not be present
(unconfigured) or the
signature present in
nonvolatile RAM may not
match the signature on the
controller.
Run the System
Configuration Utility to
configure the controller and
nonvolatile RAM.
DAAD recorded
errors attempting
to access: X
DAAD found errors while
attempting to access physical
drive X, believed to be
operational. Message
followed by specific
information about the error.
Replace the drive, or
correct the condition that
caused the error.
Disable command
issued
Posted writes have been
disabled by the issuing of the
Accelerator Disable
command. This occurred
because of an operating
system device driver.
Restart the system. Run the
System Configuration Utility
to reinitialize the array
accelerator board.
Drive (bay) X
needs replacing
(DAAD Error 102)
The 210-megabyte hard drive
has firmware version 2.30 or
2.31.
Replace the drive.
Drive Monitoring
features are
unobtainable
DAAD unable to get monitor
and performance data due
to fatal command problem
such as drive time-out, or
unable to get data due to
these features not supported
on the controller.
Check for other errors (timeouts, etc.). If no other errors
occur, upgrade the
firmware to a version that
supports monitor and
performance, if desired.
Drive Monitoring is
NOT enabled for
drive bay X
The monitor and performance
features have not been
enabled.
Run the System
Configuration Utility to
initialize the monitor and
performance features.
Drive time-out
occurred on
physical drive bay
X
DAAD issued a command to a
physical drive and the
command was never
acknowledged.
The drive or cable may be
bad. Check the other error
messages on the
Diagnostics screen to
determine resolution.
Drive (bay) X
firmware needs
Firmware on this physical drive
is below the latest
Run the Options ROMPaq
Utility to upgrade the drive
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-61
upgrading
recommended version.
firmware to the latest
revision.
Drive (bay) X has
invalid M&P stamp
Physical drive has invalid
monitor and performance
data.
Run the System
Configuration Utility to
properly initialize this drive.
Drive X indicates
position Y
Message indicates which
physical drive appears to be
scrambled or in a drive bay
other than the one for which it
was originally configured.
Examine the graphical drive
representation on DAAD to
determine proper drive
locations. Remove drive X
and place it in drive position
Y. Rearrange the drives
according to the DAAD
instructions.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-62 Diagnostic Tools
DAAD Diagnostic Messages
Message
Continued
Description
Recommended Action
Drive (bay) X RIS
copy mismatch
The copies of the RIS on this
drive do not match.
This drive may need to be
replaced. Check for other
errors.
Drive (bay) X
upload code not
readable
An error occurred while DAAD
was trying to read the upload
code information from this
drive.
If there were multiple errors,
this drive may need to be
replaced.
Duplicate write
memory error
Data could not be written to
the array accelerator board in
duplicate due to the
detection of parity errors. This
is not a data loss situation.
Replace the array
accelerator board.
Error occurred
reading RIS copy
from drive (bay) X
An error occurred while DAAD
was trying to read the RIS from
this drive.
If there were multiple errors,
this drive may need to be
replaced.
FYI: Drive (bay) X is
non-Compaq
supplied
The installed drive was not
supplied by Compaq.
If problems exist with this
drive, replace it with a
Compaq drive.
Identify controller
data did not
match with
NVRAM
The identify controller data
from the array controller did
not match with the
information stored in
nonvolatile RAM. This could
occur if new, previously
configured drives have been
placed in a system that has
also been previously
configured. It could also
occur if the firmware on the
controller has been upgraded
and the System Configuration
Utility was not run.
Check the identify
controller data under the
Inspect Utility. If the
firmware version field is the
only thing different
between the controller and
nonvolatile RAM data, this is
not a problem. Otherwise
run the System
Configuration Utility.
Identify logical
drive data did not
match with
NVRAM
The identify unit data from the
array controller did not match
with the information stored in
nonvolatile RAM. This could
occur if new, previously
configured drives have been
placed in a system that has
also been previously
configured.
Run the System
Configuration Utility to
configure the controller and
nonvolatile RAM.
Insufficient
The adapter does not have
Operate the system without
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-63
adapter resources
sufficient resources to perform
operations to the array
accelerator board. Drive
rebuild may be occurring.
the array accelerator board
until the drive rebuild
completes.
Less than 75%
batteries at
sufficient voltage
The operation of the array
accelerator board has been
disabled due to less than 75%
of the battery packs being at
the sufficient voltage level.
Allow sufficient time for the
batteries to recharge (36
hours). If the batteries have
not recharged after 36
hours, replace the array
accelerator board.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-64 Diagnostic Tools
DAAD Diagnostic Messages
Message
Continued
Description
Recommended Action
Logical drive X
failed due to
cache error
This logical drive failed due to
a catastrophic cache error.
Replace the array
accelerator board and
reconfigure using the
System Configuration Utility.
Logical Drive X
status = FAILED
This status could be issued for
several reasons. If this logical
drive is configured for No Fault
Tolerance and one or more
drives fail, this status will occur.
If mirroring is enabled, and
any two mirrored drives fail,
this status will occur. If Data
Guarding is enabled, and two
or more drives fail in this unit,
this status will occur. This status
may also occur if another
configured logical drive is in
the WRONG DRIVE REPLACED
or LOOSE CABLE DETECTED
state.
Check for drive failures,
wrong drive replaced, or
loose cable messages. If
there was a drive failure,
replace the failed drive(s)
and then restore the data
for this logical drive from the
tape backup. Otherwise,
follow the wrong drive
replaced or loose cable
detected procedures.
Logical Drive X
status = INTERIM
RECOVERY
A physical drive in this logical
drive has failed. The logical
drive is operating in interim
recovery mode and is
vulnerable.
Replace the failed drive as
soon as possible.
Logical Drive X
status = LOOSE
CABLE DETECTED
A physical drive has a cabling
problem.
Turn the system off and
attempt to reattach the
cable onto the drive. If this
does not work, replace the
cable.
Logical Drive X
status = NEEDS
RECOVER
A physical drive in this logical
drive has failed and has now
been replaced. This drive
needs to be rebuilt from the
mirror drive or the parity data.
When booting up the
system, select the "F1 rebuild drive" option to
rebuild the replaced drive.
Logical Drive X
status =
OVERHEATED
The temperature of the
Intelligent Array Expansion
System drives is beyond safe
operating levels and it has
shut down to avoid damage.
Check the fans and the
operating environment.
Logical Drive X
status =
The temperature of the
Intelligent Array Expansion
Check the fans and the
operating environment.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-65
OVERHEATING
System drives is beyond safe
operating levels.
Logical Drive X
status =
RECOVERING
A physical drive in this logical
drive has failed and has now
been replaced. The replaced
drive is rebuilding from the
mirror drive or the parity data.
Nothing needs to be done.
Normal operations can
occur.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-66 Diagnostic Tools
DAAD Diagnostic Messages
Message
Continued
Description
Recommended Action
Logical Drive X
status = WRONG
DRIVE REPLACED
A physical drive in this logical
drive has failed. The incorrect
drive was replaced.
Replace the drive that was
incorrectly replaced. Then,
replace the original drive
that failed with a new drive.
Do not run the System
Configuration Utility to
reconfigure; you will lose
data on the drive.
Loose cable
detected - logical
drives may be
marked FAILED
until corrected
Controller unable to
communicate with one or
more physical drives, probably
because of a cabling
problem. Logical drives may
be in a FAILED state until the
condition is corrected,
preventing access to data on
the controller.
Check all controller and
drive cable connections.
Mirror data
miscompare
Data was found at
reinitialization in the posted
write memory; however, the
mirror data compare test
failed resulting in data being
marked as invalid. Data loss is
possible.
Replace the array
accelerator board.
Mirrored memory
location errors
Soft errors occurred when
attempting to read the same
data from both sides of the
mirrored memory. Data loss
will occur.
Replace the array
accelerator board.
No configuration
for Accelerator
Board
The array accelerator board
has not been configured.
If the array accelerator
board is present, run the
System Configuration Utility
to configure the board, if
desired.
Drive (bay) X has
loose cable
The array controller could not
communicate with this drive
at power-up. This drive has not
previously failed.
Check all cable
connections first. The cables
could be bad, loose, or
disconnected. Turn on the
system and attempt to
reconnect data/power
cable to the drive. If this
does not work, replace the
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-67
cable. If that does not work,
the drive may need to be
replaced.
Drive (bay) X is a
replacement drive
This drive has been replaced.
This message displays if a drive
is replaced in a fault tolerant
logical volume.
If the replacement was
intentional, allow the drive
to rebuild.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-68 Diagnostic Tools
DAAD Diagnostic Messages
Message
Continued
Description
Recommended Action
Drive (bay) X is a
replacement drive
marked OK
This drive has been replaced
and marked OK by the
firmware. This may occur if a
drive has an intermittent
failure (for example, if a drive
has previously failed, then
when DAAD is run, the drive
starts working again).
Replace the drive.
Drive (bay) X is
failed
The indicated physical drive
has failed.
Replace this drive.
Drive (bay) X has
insufficient
capacity for its
configuration
Drive has insufficient capacity
to be used in this logical drive
configuration.
Replace this drive with a
larger capacity drive.
Drive (bay) X is
undergoing drive
recovery
This drive is being rebuilt from
the corresponding mirror or
parity data.
Normal operations should
occur.
Drive (bay) X was
inadvertently
replaced
The physical drive was
incorrectly replaced after
another drive failed.
Replace the drive that was
incorrectly replaced and
replace the original drive
that failed. Do not run the
System Configuration Utility
and try to reconfigure; data
will be lost.
SCSI port X, drive
ID Y firmware
needs upgrading
Drive’s firmware may cause
problems and should be
upgraded.
Run Options ROMPaq to
upgrade the drive’s
firmware to a later revision.
Set configuration
command issued
The configuration of the array
controller has been updated.
The array accelerator board
may remain disabled until it is
reinitialized.
Run the System
Configuration Utility to
reinitialize the array
accelerator board.
Soft Firmware
Upgrade required
DAAD has determined that
your controller is running
firmware that has been soft
upgraded by the Compaq
Upgrade Utility. However, the
firmware running is not
present on all drives. This
could be caused by the
addition of new drives in the
system.
Run the Compaq Upgrade
Utility to place the latest
firmware on all drives.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-69
Threshold for drive
(bay) X violated
This message indicates that a
monitor and performance
threshold for this drive has
been violated.
Check for the particular
threshold that has been
violated.
Threshold
violations for drive
(bay) X
This is a list of the individual
thresholds that have been
violated for this drive.
The drive may need to be
replaced. Run the Compaq
Diagnostics Utility to
determine if the drive has
been initialized and the
threshold violation warrants
drive replacement.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-70 Diagnostic Tools
DAAD Diagnostic Messages
Message
Continued
Description
Recommended Action
Unknown disable
code
A code was returned from the
array accelerator board that
DAAD does not recognize.
Obtain the latest version of
DAAD.
Warning bit
detected
A monitor and performance
threshold violation may have
occurred. The status of a
logical drive may not be OK.
Check the other error
messages for an indication
of the problem.
WARNING - Drive
Write Cache is
enabled on X
Drive has its internal write
cache enabled. The drive
may be a third-party drive or
the drive’s operating
parameters may have been
altered. Condition may cause
data corruption if power to
the drive is interrupted.
Replace the drive with a
Compaq supplied drive, or
restore the drive’s operating
parameters.
Wrong
Accelerator
This could mean that either
the board was replaced in
the wrong slot or placed in a
system that was previously
configured with another
board type. Included with this
message is a message
indicating the type of
adapter sensed by DAAD and
a message indicating the
type of adapter last
configured in EISA nonvolatile
RAM.
Check the diagnosis screen
for other error messages.
Run the System
Configuration Utility to
update the system
configuration.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-71
Integrated Management Log
On servers supporting the Integrated Management Display, Compaq Integrated
Management Display Log replaces the Critical Error Log and Correctable Memory Logs,
recording system events and storing them in an easily viewable form. It marks each event
with a time-stamp with one-minute granularity.
Events listed in the Integrated Management Log are categorized as one of four event
severity levels:
■
Status--indicates that the message is informational only.
■
Repaired--indicates that corrective action has been taken.
■
Caution--indicates a non-fatal error condition.
■
Critical--indicates a component failure.
The Integrated Management Log requires Compaq Operating System-dependent drivers.
Refer to the Compaq Support Software CD for instructions on installing the appropriate
drivers.
Multiple Ways of Viewing the Log
You can view an event in the Integrated Management Log in several ways:
■
On the Integrated Management Display
■
From within Compaq Insight Manager
■
From within Compaq Survey Utility
■
IML Management Utility
Integrated Management Display
The Integrated Management Display is an LCD display panel that presents information
directly at the server, assisting in diagnosing and servicing the server without a keyboard
and monitor.
Compaq Insight Manager
Compaq Insight Manager is a server management tool that provides in-depth fault
configuration and performance monitoring of hundreds of Compaq servers from a single
management console. System parameters that are monitored describe the status of all key
server components. By being able to view the events that may occur to these components,
you can take immediate action. You can view and print the event list from within Insight
Manager by following the instructions below. You can also mark a critical or caution event
as repaired after the affected component has been replaced, for example, if a fan that has
failed has been replaced. By marking as repaired, you can lower the severity of the event.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-72 Diagnostic Tools
Viewing the Event List
1.
From Compaq Insight Manager, select the appropriate server, then select View
Device Data.
The selected server is displayed with buttons around its perimeter.
2.
Select the Recovery button.
3.
Select Integrated Management Log.
NOTE: You can only view the list from the Recovery/Integrated
Management screen. To print the list, follow the instructions below.
4.
If a failed component has been replaced, select the event from the list, then select
Mark Repaired.
Printing the Event List
NOTE: You can only view the list from the Recovery/Integrated
Management Log screen as described above. To print the list,
follow the instructions below.
1.
From the Insight Manager, select the appropriate server.
2.
Select the Configuration button.
3.
Select the Recovery button.
4.
Select Print.
Compaq Survey Utility
The Compaq Survey Utility is a serviceability tool available from Windows NT and Novell
NetWare that delivers online-configuration capture and comparison to maximize server
availability. It is delivered on the Compaq Management CD in the SmartStart package or is
available on the Compaq web site. Refer to the Compaq Management CD for information
on installing and running the Survey Utility.
After running the Survey Utility, you can view the Integrated Management Log by loading
the output of the utility (typically called “survey.txt”) into a text viewer such as Notepad.
The event list follows the system slot information. Once you have opened the text file, you
can print it using the print feature of the viewer.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-73
List of Events
The event list displays the affected components and the associated error messages. Though
the same basic information is displayed, the format of the list may be different, depending
on how you are viewing it: on the Integrated Management Display, from within Compaq
Insight Manager, or from within the Compaq Survey Utility. An example of the format of
an event as displayed on the Integrated Management Display is as follows:
**001 of 010**
---caution--03/19/1997
12:54 PM
FAN INSERTED
Main System
Location:
System Board
Fan ID: 03
**END OF EVENT**
Table 3-21
Event Messages
Event Type
Machine Environment
Fan Failure
Fan Inserted
Fan Removed
Fans Not Redundant
Overheat Condition
Main Memory
Correctable Error threshold
exceeded
Uncorrectable Error
Processor
Correctable Error Threshold
exceeded
Uncorrectable Error
Host Bus Error
Event Message
System Fan Failure (Fan X, Location)
System Fan Inserted (Fan X, Location)
System Fan Removed (Fan X, Location)
System Fans Not Redundant
System Overheating (Zone X, Location)
Corrected Memory Error threshold passed (Slot X,
Memory Module X)
Corrected Memory Error threshold passed (System
Memory)
Corrected Memory Error threshold passed (Memory
Module unknown)
Uncorrectable Memory Error (Slot X, Memory Module
X)
Uncorrectable Memory Error (System Memory)
Uncorrectable Memory Error (Memory Module
unknown)
Processor Correctable error Threshold passed (Slot X,
Socket X)
Processor Uncorrectable internal error (Slot X, Socket
X)
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-74 Diagnostic Tools
Unrecoverable Host Bus Data Parity Error
Unrecoverable Host Bus Address Parity Error
EISA Bus
EISA Expansion Bus Master Timeout (Slot X)
EISA Expansion Bus Slave Timeout
EISA Expansion Board Error (Slot X)
EISA Expansion Bus Arbitration Error
Continued
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-75
Event Messages
Continued
Event Message
Event Message
PCI Bus Error (Slot X, Bus X, Device X, Function X)
PCI Bus Error
Power Subsystem
Power Supply Failure
Power Supply Inserted
Power Supply Removed
Power Supply Not
Redundant
System Configuration Battery
Low
Power Module Failure
Power Modules Not
Redundant
AC Voltage Problem
Power AC Overload
System Power Supply Failure (Power Supply X)
System Power Supply Inserted (Power Supply X)
System Power Supply Removed (Power Supply X)
System Power Supplies Hot Redundant
Real-Time Clock Battery Failing
A CPU Power Module (System Board, Socket X)
A CPU Power Module (Slot X, Socket X)
System Power Modules Not Redundant
System AC Power Problem (Power Supply X)
System AC Power Overload (Power Supply X)
Automatic Server Recovery
System Lockup
ASR Lockup Detected: Cause
Operating System
System Crash
Automatic OS Shutdown
Blue Screen Trap: Cause [NT]
Kernel Panic: Cause [UNIX]
Abnormal Program Termination: Cause [NetWare]
Automatic Operating System Shutdown Initiated Due
to Fan Failure
Automatic Operating System Shutdown Initiated Due
to Overheat Condition
Fatal Exception (Number X, Cause)
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-76 Diagnostic Tools
Rapid Recovery Services
Compaq servers provide rapid recovery services for diagnosing and recovering from errors.
These tools are available for local and remote diagnosis and recovery.
Rapid recovery means fast identification and resolution of complex faults. The Rapid
Recovery Engine and Insight Management Agents notify the system administrator when a
failure occurs, ensuring that the server experiences minimal downtime. You enable these
features through the System Configuration Utility. These integrated server management
features are:
■
Automatic Server Recovery-2 (ASR-2)
■
Server Health Logs (on servers not supporting Integrated Management
Display Logs)
■
Storage Fault Recovery Tracking
■
Storage Automatic Reconstruction
■
Network Interface Fault Recovery Tracking
■
Memory Fault Recovery Tracking (with option upgrade kit)
These are discussed in more detail on the Systems Reference Library CD (SRL).
Automatic Server Recovery-2
Automatic Server Recovery-2 (ASR-2) lets the server restart automatically from the
operating system or the Compaq Utilities. To use this feature, you must use the System
Configuration Utility to install Compaq Utilities in the system partition.
You can tell ASR-2 to restart your server after a critical hardware or software error occurs.
Using the Compaq System Configuration Utility, configure the system for either automatic
recovery or for attended local or remote access to diagnostic and configuration tools.
You can also configure ASR-2 to page an administrator when the system restarts. ASR-2
depends on the application and driver that routinely notify the ASR-2 hardware of proper
system operations. If the time between ASR-2 notifications exceeds the specified period,
ASR-2 assumes a fault has occurred and initiates the recovery process.
To configure ASR-2, follow this procedure:
1.
Execute the System Configuration Utility.
2.
Select View and Edit Details.
3.
Set the software error recovery status to Enabled.
4.
Set the software error recovery time-out.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-77
The available recovery features are:
■
Software Error Recovery – automatically restarts the server after a softwareinduced server failure
■
Environmental Recovery – allows the server to restart when temperature, fan, or
AC power conditions return to normal
Unattended Recovery
For unattended recovery, ASR-2 logs the error information to the Critical Error Log, resets
the server, pages you (if a modem is present and you selected paging), and tries to restart
the operating system. Often the server restarts successfully, making unattended recovery
the ideal choice for remote locations where trained service personnel are not immediately
available.
ASR-2 tries to restart the server up to 10 times. If ASR-2 cannot restart the server within 10
attempts, it places a critical error in the Critical Error Log, starts the server into Compaq
Utilities, and enables remote access (if you configured remote access).
To use this level of ASR-2, you must configure ASR-2 to load the operating system after
restart.
Attended Recovery
For attended recovery, ASR-2 performs the following actions:
■
Logs the error information to the Critical Error Log
■
Resets the server
■
Pages you (if a modem is present and you selected Paging)
■
Starts Compaq Utilities from the hard drive
■
Enables remote access
During system configuration, these utilities are placed on the system utilities partition of
the hard drive.
If you have configured for dial-in access and have a modem with an auto-answer feature
installed, you can dial in and remotely diagnose or reconfigure the server.
If you have configured the Compaq Utilities for network access, you can access the utilities
over the network. You can use Compaq Insight Manager for dial-in or network access.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-78 Diagnostic Tools
Hardware Requirements
To use this level of ASR-2 over a modem, you need the following:
■
Compaq modem or optional Hayes modem
■
System Configuration Utility and Diagnostics Utility installed on the system
partition of the hard drive
■
ASR-2 configured to load Compaq Utilities after restart
You can also run Compaq Utilities remotely over an IPX or IP network using the Network
feature:
■
To use Compaq Utilities on an IPX network, you must have Compaq Insight
Manager 2.0 or later or an NVT (Novell Virtual Terminal) Terminal Emulator with
VT100 or ANSI terminal capabilities.
■
To use Compaq Utilities on an IP network, you must have Compaq Insight Manager
2.10 or later, or a Telnet Terminal Emulator with VT100 or ANSI capabilities.
If you are notified that ASR-2 restarted the server and you have restarted to Compaq
Utilities, use the Inspect Utility or Compaq Insight Manager to view the critical error in the
Critical Error Log. Run Diagnostics to diagnose and resolve the problem.
You can configure ASR-2 to restart the server into Compaq Utilities to diagnose the critical
error, or to start the operating system to return the server to operational status as rapidly as
possible.
When you enable ASR-2 to start the operating system, the server tries to start from the
primary partition. In this mode, ASR-2 can page you if a critical error occurs, but you
cannot access Compaq Utilities.
When you enable ASR-2 to start Compaq Utilities, your server restarts after a critical error
and loads Compaq Utilities from the system partition on the hard drive.
You can configure your server to start Compaq Utilities in four different ways:
■
Without remote console support; for example, to run Compaq Utilities from the
server console only
■
With remote console support using modems for dial-in access
■
With remote console support using a modem to dial a predetermined telephone
number
■
With remote console support through a network connection (IP or IPX)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-79
Compaq Integrated Remote Console
The standard Compaq Integrated Remote Console performs a wide range of configuration
activities. Some of the console’s features include:
■
Accessible using ANSI terminal
■
Operates independently of the operating system
■
Provides for remote server reboot
■
Provides access to system configuration
■
Uses out-of-band communication with dedicated management modem installed in
the server
For more information, see the Integrated Remote Console User Guide.
IMPORTANT: Before configuring ASR-2, verify that the System
Configuration Utility and Diagnostics software are installed on the
system partition. ASR-2 must have this to start Compaq Utilities after
a system restart. Compaq recommends this even if you configure
ASR-2 to start the operating system.
Compaq Health Driver
The Compaq Health Driver continually resets the ASR-2 timer according to the frequency
you specified in the System Configuration Utility (for example, 10 minutes). If the ASR-2
timer counts down to zero before being reset, due to an operating system crash, or a server
lock-up, ASR-2 restarts the server into either Compaq Utilities or the operating system (as
indicated by the System Configuration parameters). The default value is 10 minutes. The
allowable settings are 5, 10, 20, and 30 minutes
For remote and off-site (unattended) servers, setting the software error recovery time-out
for 5 minutes reduces the server downtime and allows the server to recover quickly. For
local (attended) servers located onsite, you can set the software error recovery time-out for
20 or 30 minutes, giving you time to arrive at the server if you wish to manually diagnose
the problem.
The Compaq Health Driver is independent of the ASR-2 timer. You should load it enabling
the ASR-2 timer. This allows the driver to detect and log information about numerous
hardware and software errors in the Integrated Management Log. However, you cannot
enable the ASR-2 timer without loading the Compaq Health Driver.
Before ASR-2 restarts the server, it will record any information available about the
condition of the operating system in the Critical Error Log, or the Integrated Management
Log depending on the server support. This information can be used to diagnose an
operating system crash or server lock-up, while still allowing the server to be restarted.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-80 Diagnostic Tools
The following ASR-2 flow chart shows you the sequence of events after a hardware or
software error occurs:
Hardware/Software error occurs
|
Error records in the Server Health Log or
in the Integrated Management Log,
depending on the server
|
Operating System halts normal operation
|
ASR Timer expires
|
Server is reset
|
If a modem is installed and paging
is enabled, the Server Failure Notification
pager alert is sent to
the Server Administrator
|
Unattended server boots the
---Or--Server boots the Compaq Utilities
Operating System
on the system partition on the hard
drive

|
If the server continues experiencing
If a modem is installed, ASR puts
hardware/software errors and the
the modem on auto answer so that
number of ASR cycles exceed the
the Server Administrator can dial in
specified number of recovery
using third party terminal emulator
attempts, the server will log an error
software to remotely run the
to the Server Health Log or the
Compaq Utilities to identify the
Integrated Management Log and
source of the fault
boot the Compaq Utilities from the
system partition on the hard drive
|
Or
|
Local Server Administrator runs
Compaq Utilities from server
console to identify the source of the
fault
Figure 3-1. ASR-2 Flow Chart
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-81
Booting into Compaq Utilities
When you enable ASR-2 to start into Compaq Utilities and a critical error occurs, the
operating system-specific Health Driver logs the error information in the Critical Error Log
and the ASR-2 feature restarts the server. When the system reinitializes, the system pages
the designated administrator (if enabled), and starts Compaq Utilities from the hard drive.
If Dial-In status is enabled, the modem is placed in auto-answer mode. If you enable DialOut status, you are automatically enabled for Dial-In.
If Network Status is enabled, the appropriate network support software is loaded,
depending on the network protocol, IP or IPX. This allows remote access via the network.
IMPORTANT: Compaq Utilities are loaded from a specially created
system partition on the hard drive. This partition was configured
during server configuration.
You can access the server and view the Server Health Logs in servers not supporting the
Integrated Management Display Log, remotely by modem, in-band over the network, or
directly from the server. For modem access, you must have either Compaq Insight Manager
2.0 or above or have a VT100 or ANSI terminal type device. You may use a standard CRT
with VT100 or ANSI emulation capability, or you may use a PC with a VT100 or ANSI
terminal emulation package. The communication parameters must be set for 8 data bits, no
parity, and 1 stop bit.
You can also enable ASR-2 to allow network access using the Network Status feature in the
System Configuration Utility. You must have either Compaq Insight Manager 2.0 or greater
or a Novell Virtual Terminal (NVT) emulator on an IPX network to use this feature. You
must also have version 2.24 or later of the System Configuration Utility. For IP access, you
must have either Compaq Insight Manager 2.10 or later, or a Telnet Terminal emulator to
use this feature. You also must have version 2.24 or later of the System Configuration
Utility.
The System Configuration Utility settings should resemble the settings in the following
table when you enable ASR-2 to start into Compaq Utilities.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-82 Diagnostic Tools
Table 3-22
Compaq System Configuration Utility Pager Settings
for Booting into Compaq Utilities
Pager
Data
Setting
Description
Pager
status
Enabled
Indicates if the pager feature is enabled or disabled.
Pager
dial string
ATDT 5555555
Indicates the pager dial string and delay before the
pager message. Pagers typically use one of the
following formats:
Local pagers: ATDT 555-5555
Wide area pagers: ATDT 1-800-555-5555,1234567#
Pager
message
1234567#
Represents a unique number (maximum seven digits,
numeric only) that you must designate to identify the
server on your pager display. The ROM adds a threedigit code to the front of this number. The first two
indicate the subsystem and the third indicates the
severity of the error that caused the alert. The # symbol
usually terminates the message. If no message is
required, delete the # symbol.
Pager
test
Select to
test
pager
setup
Use this to test the current pager settings. Press Enter to
dial the pager number, and the pager message (if
present) displays. You must configure the computer
before testing the pager and the Pager Status must be
set to Enabled. Do not test the pager if you are running
remotely and are using only one modem.
Serial
interface
COM1
Select the communications port for the modem used by
the pager and the remote ASR-2 functions. The options
are COM1 and COM2.
Dial-in
status
Enabled
Set Dial-In Status to Enabled. Be sure the Reset Boot
option is set to Boot Compaq Utilities. When the system
starts because of an ASR reset, it starts to the Compaq
Utilities, sets the Management Modem to auto-answer,
and waits for the administrator to dial in and run the
Compaq Utilities.
You automatically disable this option when you
configure the software error recovery start option to
Boot Operating System. When ASR pages you, you
cannot dial in unless ASR-2 exceeds 10, the threshold
number of server restart retries. When this happens, ASR2 restarts the server into the Compaq Utilities and places
the modem in auto-answer mode.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-83
Dial-out
status
Enabled
Allows ASR-2 to dial out to a remote workstation. If you
selected this option, Dial In Status is automatically
selected.
To use the dial-out feature, set Dial-Out Status to
Enabled and set the Dial-Out String to the correct
phone number. You must also set the Reset Boot option
to Boot Compaq Utilities. When the system restarts
because of an ASR reset, the administrator is paged via
Pager Status and Pager Dial String, the system restarts to
the Compaq Utilities, and dials out to the phone
number provided in the Dial-Out string. The dial-out
number will be tried five times. If it fails to connect after
five attempts, the modem is put in auto-answer mode.
Continued
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-84 Diagnostic Tools
Compaq System Configuration Utility Pager Settings
for Booting into Compaq Utilities Continued
Pager
Data
Setting
Dial-out
string
555-1234
Enter the dial string followed by the remote computer's
telephone number.
Network
status
Enabled
To allow network access to Compaq Utilities, set
Network Status to Enabled and make sure the Reset
Boot option is set to Boot Compaq Utilities.
Network
protocol
Description
To use IPX network access, set Network Protocol to IPX.
When the system restarts to the Compaq Utilities
because of an ASR reset, it loads IPX network support.
This enables remote access via NVT.
To use IP network access, set Network protocol to IP.
Also make sure to set Network IP address, Network IP net
mask, and Network IP router address. When the system
restarts to the Compaq Utilities because of an ASR reset,
it loads IP network support. This enables remote access
via Telnet.
NOTE: The Network Status must be set to Enabled for
network access.
Network
controller
Compaq
For all Compaq Standard Network Controllers.
Network
host
name
CPQHOU
Enter the network name of the server. Use underscores
instead of spaces within the name, for example,
Compaq_Server. If you are using IPX network access to
the Compaq Utilities, this server name is used to
advertise NVT host services. This server name displays in
the Compaq Insight Manager server list when it
determines it can communicate via NVT. Set this name
to be the same as the server name you assign when the
host OS is running.
Network
card slot
Slot #
Select the slot number of the network interface card
you wish to use for network access to Compaq Utilities.
Network
frame
type
ETHERNET
_I I
Select the frame type for your network. Selections
include both Ethernet and Token Ring topologies.
Network
IP address
Enter the IP address for this server in standard dot
notation.
NOTE: This is not used if you select Custom for Network
controller. You must enter your IP address in the NET.
CFG file that you load into the system partition.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-85
Network
IP net
mask
Enter the net mask for this server in standard dot
notation.
NOTE: This is not used if you select Custom for network
controller. You must enter your IP address in the NET.
CFG file that you load into the system partition.
Network
IP router
address
Enter the router to be used for this server in standard dot
notation.
NOTE: This is not used if you select Custom for network
controller. You must enter your IP address in the NET.
CFG file that you load into the system partition.
If you configure the server to boot into Compaq Utilities, it prepares for remote
communications. You can remotely run Diagnostics software, Inspect Utility, or System
Configuration Utility using a workstation running terminal emulation software, such as
Compaq Insight Manager or PC Anywhere.
Booting into the Operating System
When you enable ASR-2 to restart into the operating system and a critical error occurs,
ASR-2 logs the error in the Critical Error Log and restarts the server. The system ROM
pages the designated administrator, and executes the normal restart process.
IMPORTANT: When you enable ASR-2 to restart into the operating
system, Modem Dial-In Status, Network Status, and Modem Dial-Out
Status are automatically disabled. In this mode, ASR-2 can page
you if a critical error occurs, but you cannot access the server, and
the server cannot dial out to a remote workstation.
During the recovery process, the ASR-2 feature tries to restart the server up to 10 times. If
the ASR-2 feature cannot restart the server within 10 attempts, it logs a critical error in the
Critical Error Log, restarts the server into the Compaq Utilities, and puts the modem into
auto-answer mode.
Your System Configuration Utility setting should resemble the following when you enable
ASR to restart into the operating system:
■
Serial interface
COM1
■
Dial-in status
Disabled
■
Dial-out status
Disabled
■
Dial-out string
555-1234
■
Network status
Disabled
■
Network protocol
IPX
■
Network controller
Compaq
■
Network host name
CPQHOU
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-86 Diagnostic Tools
■
Network card slot
Slot #
■
Network frame type
ETHERNET_II
■
Network IP address
xxx.xxx.xxx.xxx
■
Network IP net mask
xxx.xxx.xxx.xxx
■
Network IP router
address
xxx.xxx.xxx.xxx
ASR-2 Security
The standard Compaq password features function differently during ASR-2 than during a
typical system startup.
During ASR-2, the system does not prompt for the Power-On Password. This allows the
ASR-2 to restart the operating system or Compaq Utilities without user intervention.
To maintain system security, set the server to boot in Network Server Mode (an option in
the System Configuration Utility). This option ensures that the server keyboard is locked
until you enter the Keyboard Password.
Select an Administrator Password (an option in the System Configuration Utility). During
attended ASR-2 (local or remote), you must enter this Administrator Password before any
modifications can be made to the server configuration.
Server Health Logs
In some servers, Server Health Logs are replaced by the Integrated Management Log, if it
is supported. See “Integrated Management Display” in this chapter for more information.
The Server Health Logs contain information to help identify and correct any server failures
and correlate hardware changes with server failure. The Server Health Logs are stored in
nonvolatile RAM and consist of the Critical Error Log and the Revision History Table.
If errors occur, information about the errors is automatically stored in the Critical Error
Log.
Whenever boards or components (that support revision tracking) are updated to a new
revision, the Revision History Table will be updated.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-87
Critical Error Log
The Critical Error Log records memory errors, as well as catastrophic hardware and
software errors that cause the system to fail. This information helps you quickly identify
and correct the problem, thus minimizing downtime.
You can view the Critical Error Log through the Compaq Insight Manager. The Diagnostics
Utility either resolves the error or suggests corrective action in systems that do not support
event logs.
The Critical Error Log identifies and records all the following errors. Each error type is
briefly explained below.
Table 3-23
Critical Error Log Messages
Message
Description
Abnormal Program
Termination
The operating system has encountered an abnormal situation
that has caused a system failure.
ASR-2 detected by
ROM
An ASR-2 activity has been detected and logged by the
system ROM.
ASR-2 Test Event
The System Configuration Utility generated a test alert.
Automatic Server
Recovery Base
Memory Parity Error
The system detected a data error in base memory following a
reset due to the Automatic Server Recovery-2 (ASR-2) timer
expiration.
Automatic Server
The system detected a data error in extended memory
Recovery Extended following a reset due to the ASR-2 timer expiration.
Memory Parity Error
Automatic Server
Recovery Memory
Parity Error
The system ROM was unable to allocate enough memory to
create a stack. Then, it was unable to put a message on the
screen or continue booting the server.
Automatic Server
Recovery Reset
Limit Reached
The maximum number of system resets due to ASR-2 timer
expiration has been reached, resulting in the loading of
Compaq Utilities.
Battery Failing
Low system battery warning. Replace battery within 7 days to
prevent loss of nonvolatile configuration memory. Failure of
the battery supporting the system’s nonvolatile RAM is
imminent.
Caution:
Temperature
Exceeded
The operating system has detected that the temperature of
the system has exceeded the caution level. Accompanying
data in the log notes if an auto-shutdown sequence has been
invoked by the operating system.
Diagnostic Error
An error was detected by the Diagnostics Utility. See the
specific error code in this chapter for a detailed explanation.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-88 Diagnostic Tools
Error Detected On
Boot Up
The server detected an error during the Power-On Self-Test
(POST).
Processor Prefailure
A CPU has passed an internal corrected error threshold;
excessive internal ECC cache errors .
Continued
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-89
Critical Error Log Messages
Message
Continued
Description
NMI - PCI Bus Parity
Error
A parity error was detected on the PCI bus.
NMI - Expansion
Board Error
A board on the expansion bus indicated an error condition,
resulting in a server failure.
NMI - Expansion Bus
Master Time-Out
A bus master expansion board in the indicated slot did not
release the bus after its maximum time, resulting in a server
failure.
NMI - Expansion Bus
Slave Time-Out
A board on the expansion bus delayed a bus cycle beyond
the maximum time, resulting in a server failure.
NMI - Fail-Safe Timer Software was unable to reset the system fail-safe timer,
Expiration
resulting in a server failure.
Processor Exception The indicated processor exception occurred.
NMI - Processor
Parity Error
The processor detected a data error, resulting in a server
failure.
Server Manager
Failure
An error occurred with the Server Manager/R.
NMI - Software
Software indicated a system error, resulting in a server failure.
Generated Interrupt
Detected Error
Caution:
Temperature
Exceeded
The operating system has detected that the temperature of
the system has exceeded the caution level. Accompanying
data in the log notes if an auto-shutdown sequence has been
invoked by the operating system.
Abnormal Program
Termination
The operating system has encountered an abnormal situation
that has caused a system failure.
ASR-2 Test Event
The System Configuration Utility generated a test alert.
NMI- Automatic
Server Recovery
Timer Expiration
The operating system has received notice of an impending
ASR-2 timer expiration.
Required System
Fan Failure
The required system fan has failed. Accompanying data in the
log notes if an auto-shutdown sequence has been invoked by
the operating system.
UPS A/C Line Failure The UPS notified the operating system that the AC power line
Shutdown or Battery has failed. Accompanying data indicates if an auto-shutdown
Low
sequence has been invoked or if the battery has been nearly
depleted.
ASR-2 detected by
ROM
An ASR-2 activity has been detected and logged by the
system ROM.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-90 Diagnostic Tools
Revision History Table
Some errors can be resolved by reviewing changes to the server’s configuration. The server
has an Automatic Revision Tracking (ART) feature that helps you review recent changes to
the server’s configuration.
One ART feature is the Revision History Table, which contains the hardware version
number of the system board and any other system boards providing ART-compatible
revision information. This feature lets you determine the level of functionality of an
assembly in a system without opening or powering down the unit.
Table 3-24
Revision History Format
Current Revisions
Data
10/31/95
System Board Revision
03
Assembly Version
1
Functional Revision
Level
C
Processor 01 Revision
01
Assembly Version
Functional Revision
Level
1
A
Previous Revisions
Date
9/21/95
System Board Revision
03
Assembly Version
1
Functional Revision
Level
C
Processor 01 Revision
01
Assembly Version
Functional Revision
Level
1
A
The Revision History Table is stored in nonvolatile RAM and is accessed through Inspect
Utility and Compaq Insight Manager.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-91
Storage Fault Recovery Tracking
This feature tracks over 12 failure-indication parameters, such as time-outs, spin-up and
self-test errors of SCSI drives. You can use these parameters to pinpoint failed storage
subsystem components and to recover from controller or hard drive failure.
Storage Automatic Reconstruction
This feature automatically reconstructs data to an online spare or to a replaced drive if a
drive fails. To use the reconstruction feature, you must configure your server for drive
mirroring or data guarding. The reconstruction decreases system downtime by allowing
rapid recovery to full system operation if a drive fails.
Network Interface Fault Recovery Tracking
This feature tracks over 20 failure indication parameters, such as alignment errors, lost
frames, and frame copy errors, of Ethernet and Token Ring network interfaces. It decreases
network downtime by enabling diagnosis of actual network interface failures.
Memory Fault Recovery Tracking
This feature inspects the operation of the memory subsystem looking for uncorrectable
memory errors.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-92 Diagnostic Tools
Remote Service Features
Compaq servers have the following management features that you can access by modem or
network:
Table 3-25
Compaq Servers Remote Management Features
Feature
Description
Service Session
Provides remote access to all the utilities on the system partition,
including Diagnostics utilities, Inspect, ROMPaq, Drive Array
Advanced Diagnostics (DAAD), and the System Configuration
Utility. Also provides the capability for remote file transfer services
to and from the system partition.
Disk-Based
Diagnostics
Provides remote diagnostic capability after you configure ASR-2
and the reset restart option to restart from Compaq Utilities. Also
allows you to view Health Logs. Disk-based diagnostics can also
be run locally. Press F10 during the restart process when the cursor
moves to the upper-right corner of the monitor.
Server Restart
Provides the ability to restart the server remotely from Compaq
Insight Manager while the operating system is running. Allows the
server to restart back to the operating system or restart to the
system partition. Provides a complete system reset to all
peripherals. If you select Boot to Compaq Utilities from Compaq
Insight Manager, Compaq Utilities loads the appropriate remote
services so that remote access is available. If network status is
enabled, network support is loaded. If Dial-In status is enabled,
the modem is set to auto-answer.
Configuration
Utility
Allows you to run the System Configuration Utility remotely. You
can also run the remote configuration utility locally. Press F10
during the restart process when the cursor moves to the upperright corner of the monitor.
Firmware
Updates
Allows you to update the server's firmware remotely. Uses
firmware images on the system partition that might have been
previously uploaded with the file transfer services.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-93
ROMPaq
Using flash ROM in Compaq servers allows the firmware (BIOS) to be upgraded with
system or option ROMPaq utilities. To upgrade the ROM:
■
Run the ROMPaq utility from the system partition, or
■
Insert a ROMPaq diskette into drive A and cold boot the system.
The ROMPaq utility then checks the system and provides a choice (if more than one exists)
of ROM revisions to which the system can be upgraded. This procedure is the same for
both system and option ROMPaq utilities.
CAUTION: Do not turn the power off during a firmware
upgrade. A loss of
power during upgrade may corrupt the firmware and
prevent the system from booting.
Compaq Insight Manager
Compaq Insight Manager is the Compaq application for easily managing network devices.
Compaq Insight Manager delivers intelligent monitoring and alerting as well as visual
control of your servers.
Features of Compaq Insight Management
Compaq Insight Management features include:
■
Comprehensive Fault Management - For all major subsystems, including pre-failure
alerting for disks, memory, and Pentium Pro processors.
■
Integration Management - In conjunction with SmartStart, allows you to effectively
deploy and manage configurations throughout the enterprise using the Integration
Server and Insight Version Control.
■
Performance Management - Sets performance and capacity thresholds for
management variables related to CPU and bus utilization, NIC throughput, logical
disk capacity, and so on.
■
Workstation Management - Monitors and manages Compaq Professional
Workstations.
■
Client Management - Manages faults and assets on Compaq Deskpro computers.
■
Netelligent Management - Receives alarms from Netelligent devices. Full
management of Netelligent devices is supported through integration with Compaq
Netelligent Management Software.
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-94 Diagnostic Tools
■
Asset Management - Exports asset information from the Compaq Insight Manager
database to leading database and spreadsheet applications.
■
Remote Management - Manages in-band or out-of-band devices, online or offline,
from anywhere.
■
Reporting - Using Automatic Data Collection, gathers historic performance
information for graphing or export purposes.
■
Integration with Enterprise Management Platforms - Provides integration with
leading management platforms including HP OpenView, IBM NetView, SunNet
Manager, and Microsoft Systems Management Server.
Compaq Insight Management Software
Architecture
The Compaq Insight Management software architecture is typical of other network
management solutions. It has a client/server architecture and is composed of agent software
(Compaq Insight Management Agents) and the management application software (Compaq
Insight Manager).
Insight Management Agents
Insight Agents operate on Compaq systems (such as servers and workstations), performing
in-depth monitoring of the system's state by collecting and measuring system parameters.
These parameters indicate the current state of subsystems by counting the occurrence of
particular events (for example, the number of read operations performed on a disk drive) or
monitoring the state of a critical function (such as whether or not the cooling fan is
operating).
Insight Desktop Agents operate on Compaq Deskpro computers monitoring functions that
include temperature sensing and disk pre-failure alerting.
Insight Agents provide information to management applications such as Compaq Insight
Manager, and can generate alarm notifications if significant changes occur in the fault or
performance aspects of system operation. Information is delivered to and from the Insight
Agents by the industry-standard Simple Network Management Protocol or SNMP.
Compaq Insight Manager
Compaq Insight Manager delivers intelligent monitoring and alerting as well as visual
control of your Compaq hardware. In the unlikely event of hardware failures, Compaq
Insight Manager also provides a full complement of remote maintenance and control
facilities.
For additional information, refer to the online Compaq Insight Manager User Guide on the
Systems Reference Library CD that accompanied your server.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
3-95
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
4-1
Chapter 4
Connectors, Switches, and Jumpers
This chapter provides connector, switch, and jumper information for the Compaq
ProLiant 1600 and ProLiant 1200 Servers.
Compaq ProLiant 1600 Processor Board
Components
See Table 4-1 for the names of the Compaq ProLiant 1600 processor board components.
1
2
5
3
4
6
Figure 4-1. Compaq ProLiant 1600 Processor Board Components
Table 4-1
Compaq ProLiant 1600
Processor Board Components
Reference
Component
➊
Fan connector
➋
Memory expansion board slot
➌
Secondary processor board
slot/terminator board slot
➍
SW1 - Core/Bus Ratio switch
➎
Primary processor board slot
➏
DIMM slots 1 - 4
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
4-2
Connectors, Switches, and Jumpers
Rear Connectors and LEDs
See Table 4-2 for the names of the Compaq ProLiant 1600 processor board connectors and
LEDs.
1
2
3
4
5
7
6
Figure 4-2. Compaq ProLiant 1600 Processor Board External Connectors and LEDs
Table 4-2
Compaq ProLiant 1600
Processor Board External Connectors and LEDs
Reference
Connector/LED
➊
Video connector
➋
AUI Ethernet connector
➌
RJ-45 connector
➍
NIC Active LED
➎
NIC Link LED
➏
NIC 10/100 Speed LED
➐
SCSI External Bus A connector
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
4-3
SW1 - Bus/Core Ratio Settings
The bus/core frequency ratio switch is located on the Compaq ProLiant 1600 processor
board.
Table 4-3
SW1 - Bus/Core Ratio Settings
Bus/Core
Ratio
Switch 1
1
2
3
Bit 4
66/266 MHz
OFF
ON
ON
OFF
66/300 MHz
OFF
OFF
ON
OFF
66/333 MHz
OFF
ON
OFF
OFF
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
4-4
Connectors, Switches, and Jumpers
Compaq ProLiant 1200 Processor Board
Components
See Table 4-4 for the names of the Compaq ProLiant 1200 processor board components.
2
1
4
5
3
6
Figure 4-3. Compaq ProLiant 1200 Processor Board Components
Table 4-4
Compaq ProLiant 1200
Processor Board Components
Reference
Component
➊
Fan connector
➋
Memory expansion board slot
➌
SW1 - Core/Bus Ratio switch
➍
Pentium II Processor
➎
Processor Power LED
➏
Processor Power Module
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
4-5
Rear Connectors and LEDs
See Table 4-5 for the names of the Compaq ProLiant 1200 processor board connectors and
LEDs.
1
2
4
3
5
6
7
Figure 4-4. Compaq ProLiant 1200 Processor Board External Connectors and LEDs
Table 4-5
Compaq ProLiant 1200
Processor Board External Connectors and LEDs
Reference
Connector/LED
➊
Video connector
➋
AUI Ethernet connector
➌
RJ-45 connector
➍
NIC Active LED
➎
NIC Link LED
➏
NIC 10/100 Speed LED
➐
SCSI External Bus A connector
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
4-6
Connectors, Switches, and Jumpers
SW1 - Bus/Core Ratio Settings
The bus/core frequency ratio switch is located on the Compaq ProLiant 1200 processor
board.
Table 4-6
SW1 - Bus/Core Ratio Settings
Bus/Core
Ratio
Switch 1
1
2
3
Bit 4
66/233 MHz
OFF
OFF
OFF
ON
66/266 MHz
OFF
ON
ON
OFF
66/300 MHz
OFF
OFF
ON
OFF
66/333 MHz
OFF
ON
OFF
OFF
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
4-7
System I/O Board
The Compaq ProLiant 1600 and ProLiant 1200 support the same system I/O board;
however, the boards contain different ROM code. The components, connectors, and switch
settings are the same for the Compaq ProLiant 1600 and ProLiant 1200.
Components
See Table 4-7 for the names of the Compaq ProLiant 1600 and ProLiant 1200 system I/O
board components.
1
2
3
4
5
6
7
8
9
10
11
13
12
Figure 4-5. System I/O Board Components
Table 4-7
System I/O Board Components
Reference
Component
1
Parallel Adapter Cable
2
I2O Connector
3
Replacement Battery Connector
4
Replacement Battery Jumper
5
External Speaker Connector
6
7 - 12
13
System Battery
PCI/EISA Expansion Slots
SW1 Configuration Switch
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
4-8
Connectors, Switches, and Jumpers
Rear Connectors
See Table 4-8 for the names of the Compaq ProLiant 1600 and ProLiant 1200 expansion
system board connectors.
1
3
2
4
Figure 4-6. Expansion System Board Connectors
Table 4-8
Expansion System Board Connectors
Reference
Component
1
Parallel connector
2
Serial A and B connectors
3
Mouse connector
4
Keyboard connector
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
4-9
SW1 - System Maintenance Switch
The following table defines the function for each SW1 switch setting on the Compaq
ProLiant 1600 and ProLiant 1200 system I/O board. The default positions are indicated
below. See Figure 4-5 and Table 4-7 for the location of the switch.
Table 4-9
SW1 - System Maintenance Switch Settings
Switch
Function
ON
OFF
1
Disable On-Board
Video
On-board video is disabled.
Default
2
Lock configuration
information
You cannot change
configuration information.
Default
3
Tower-to-Rack
Conversion
Converts the unit to a rack
configuration.
Default (Tower
model)
4
Disable Diskette Boot
System booting from the
diskette drive is disabled.
Default
5
Disable Password
Clears passwords.
Default
6
Clear NVRAM
Clears NVRAM.
Default
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
5-1
Chapter 5
Physical and Operating
Specifications
This section provides operating and performance specifications for Compaq ProLiant 1600
and ProLiant 1200 Servers.
■
System Unit
■
Power Supply
■
Dual Inline Memory Modules
■
Diskette Drive
■
CD-ROM Drive
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
5-2
Physical and Operating Specifications
System Unit
Table 5-1
Compaq ProLiant 1600 and ProLiant 1200
System Unit Specifications
U.S.
International
Dimensions
Height
18.63 in
47.32 cm
Depth
22.67 in
57.58 cm
Width
Weight (no hard drive installed)
10.63 in
27 cm
63 lb
29 kg
Input Requirements
Rated Input Voltage
100-240 VAC
Rated Input Frequency
50-60 Hz
Rated Input Current
6-3 A
Temperature Range
Operating
50°-95 °F
10° -35°C
Non-operating
-22°-122 °F
-30° -50°C
Relative Humidity (noncondensing)
Operating
8% to 90%
Nonoperating
5% to 95%
Maximum Wet Bulb Temperature
101.7 °F
38.7°C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
5-3
Power Supply
Compaq ProLiant 1600
Table 5-2
Compaq ProLiant 1600 Power Supply Specifications
U.S.
International
Input Specifications
Nominal Line Voltage
115 VAC
230 VAC
Range Input Line
90 VAC - 132 VAC
180 VAC - 264 VAC
Frequency Range
47Hz - 63Hz
47Hz - 63Hz
Power Factor
.98
.98
Input Current
6A
3A
Inrush Current
N/A
N/A
Holdup Time
20ms
20ms
General Specifications
Full Output Rating
325 W
325 W
Minimum Load
+5V/3A
+5V/3A
Operating
41°F - 113°F
5°C- 45°C
Storage
-40°F - 185°F
-40° - 85°C
Ambient Temperature Range
Dielectric Voltage Withstand
Input to Output
2150 VDC
Input to Ground
Common and Differential +/- 2kV
Mode (superimposed on
AC line) Differential Mode
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
5-4
Physical and Operating Specifications
Compaq ProLiant 1200
Table 5-3
Compaq ProLiant 1200 Power Supply Specifications
U.S.
International
Input Specifications
Nominal Line Voltage
115 VAC
230 VAC
Range Input Line
90-132 VAC
180-264 VAC
Frequency Range
47-63 VAC
47-63 VAC
Power Factor
.98
.98
Input Current
6 ARMS MAX
3 ARMS MAX
Holdup Time
20 ms
20 ms
Full Output Rating
280 W
280 W
Minimum Load
+5 V/3 A
+5 V/3 A
Operating
41°F - 113°F
5°C - 45°C
Storage
-40°F - 185°F
-40-85°C
General Specifications
Ambient Temperature Range
Dielectric Voltage Withstand
Input to Output
2150 VAC/min
Input to Ground
2150 VAC/min
Input Transient Susceptibility:
Common and Differential +/- 2kV
Mode (superimposed on
AC line) Differential Mode
Dual Inline Memory Modules (DIMMs)
Table 5-4
DIMM Specifications
Size
16, 32, 64, 128 MB
Speed
60 ns or faster
Upgrade Requirement
Matched pairs identical in size and speed
NOTE: Use only 16-, 32-, 64-, or 128-MB; EDO - gold-connector; 4-K refresh DIMMs.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
5-5
1.44-MB Diskette Drive
Table 5-5
1.44-MB Diskette Drive Specifications
Size
3 1/2 in
LED Indicators (front panel)
Green
Read/Write Capacity per Diskette (high/low density) 1.44 MB/720 KB
Drive Supported
One
Drive Height
One-third
Drive Rotation
300 rpm
Transfer Rate (high/low)
500K bits/sec /250K bits/sec
Bytes/Sector
512
Sectors/Track (high/low)
18/9
Tracks/Side (high/low)
80/80
Access Times:
Track-to-Track (high/low)
3 ms/6 ms
Average (high/low)
169/94 ms
Settling Time
15 ms
Latency Average
100 ms
Cylinders (high/low)
80/80
Read/Write Heads
Two
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
5-6
Physical and Operating Specifications
16X CD-ROM Drive drive
Table 5-6
16X CD-ROM Drive Specifications
Applicable Disk
CD-ROM (Mode 1 and 2)
CD-DA, CD-XA; Photo CD (single and multi-session)
Mixed Mode (audio and data combined)
Capacity
540 MB (Mode 1, 12 cm)
630 MB (Mode 2, 12 cm)
180 MB (8 cm)
Block Size
2048 bytes (Mode 1)
2340, 2336, bytes (Mode 2)
2352 bytes (CD-DA)
2328 bytes (CD-XA)
Dimensions
Height
1.68 in
42.9 mm
Depth
5.85 in
150.1 mm
8.11 in
208.0 mm
2.09 lb
.950 g
Width
Weight
Data Transfer Rate
Sustained
150 KB/s (sustained 1X),
1200 KB/s (sustained 8X)
Burst
4.0 MB/s
Access Times (typical)
Full Stroke
350 ms
Random
150 ms
Diameter
4.7 in, 3.15 in
12 cm, 8 cm
Thickness
.05 in
1.2 mm
Track pitch
1.6 µm
Cache/Buffer
128 KB
Startup Time
<7s
Stop Time
< 4 s (single); <30 s (multi-session)
Laser Parameters
Type
Semiconductor Laser GaA1As
Wave Length
790 +/- 25 nm
Divergence Angle
53.5o +/- 1.5o
Output Power
0.14 mW
Operating Conditions
Temperature
41° to 113°F
5° to 45°C
Humidity
10% to 80%
5% to 90%
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
I-1
Index
ProLiant 1600 4-3
A
Access panel
left side
removing and replacing 2-7
spares part number 1-3
right side
removing and replacing 2-9
spares part number 1-3
Advanced VGA board, test error codes 3-26
Automatic Server Recovery-2 3-46
C
Cables
folding and routing diagrams 2-14
spares part numbers 1-4
Carton and buns, spares part number 1-4
CD-ROM drive
cable folding and routing diagram 2-14
removing and replacing 2-12
spares part number 1-4
specifications 5-6
Chassis, spares part number 1-3
Compaq Insight Manager 3-61
Compaq Survey Utility 3-43
Components, exploded view 1-2
Connectors
ProLiant 1200 4-5
ProLiant 1600 4-2
Country kits, spares part numbers 1-4
Critical error log messages 3-56
B
Backplane board
removing and replacing 2-34
spares part number 1-3
Battery
installing 2-35
spares part number 1-3
Bezel
plate, spares part number 1-3
removing and replacing 2-5
spares part number 1-3
Boards
backplane
removing and replacing 2-34
spares part number 1-3
memory expansion
removing and replacing 2-28
spares part number 1-3
Pentium II adapter
removing and replacing 2-22
spares part number 1-3
system I/O
components 4-7
removing and replacing 2-16
spares part number 1-3
terminator
removing and replacing 2-23
spares part number 1-3
Bus/Core ratio settings
ProLiant 1200 4-6
D
Diagnostics (DIAGS)
software 3-17
test error codes 3-18
DIMMs
expansion board sockets 2-29
removing and replacing 2-30
specifications 5-4
upgrade combinations
ProLiant 1200 2-32
ProLiant 1600 2-32
Diskette drive
cable folding and routing diagram 2-14
removing and replacing 2-13
specifications 5-5
test error codes 3-22
Drive Array Advanced Diagnostics (DAAD)
diagnostic messages 3-33
starting 3-32
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . .
I-2
Index
Drive cage
cable folding and routing diagrams 2-15
duplexed, spares part number 1-4
removing and replacing 2-11
spares part numbers 1-3, 1-4
Drive trays, spares part numbers 1-5
Integrated Management Log 3-42
K
Keyboards, test error codes 3-20
L
E
Electrostatic discharge information 2-1
Event list 3-43
Exploded views
mechanical 1-1
system components 1-2
External replacement battery
installing 2-35
spares part number 1-3
Left side access panel
removing and replacing 2-7
spares part number 1-3
M
Maintenance and Service Guide, spares part
number 1-4
Mass storage
removing and replacing 2-10
server drive positions 2-10
spares part numbers 1-4
Mechanical parts, exploded view 1-1
Memory
expansion board
removing and replacing 2-28
spares part number 1-3
modules, spares part numbers 1-4
removing and replacing 2-30
specifications 5-4
test error codes 3-19
upgrade combinations
ProLiant 1200 2-32
ProLiant 1600 2-32
Modem communications, test error
codes 3-23
F
Fan, I/O
removing and replacing 2-17
spares part number 1-3
Feet
removing and replacing 2-6
spares part number 1-3
Front bezel
plate, spares part number 1-3
removing and replacing 2-5
spares part number 1-3
H
Hard drives
removing and replacing 2-10
spares part number 1-4, 1-5
N
NetFlex-2 controller, test error codes 3-27
I
I/O fan
removing and replacing 2-17
spares part number 1-3
Illustrated Parts Map, spares part
number 1-4
Integrated management display, spares part
number 1-4
O
Operating specifications 5-1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
I-3
conversion kit, spares part number 1-4
warnings 2-3
Rapid Recovery Services 3-46
Remote service features 3-60
Return kit, spares part number 1-4
Revision history table 3-58
Right side access panel
removing and replacing 2-9
spares part number 1-3
ROMPaq 3-61
P
Pentium II adapter board
removing and replacing 2-22
spares part number 1-3
Physical specifications 5-1
Pointing device interface, test error
codes 3-30
POST See Power-On Self-Test
Power module
removing and replacing
ProLiant 1200 2-27
ProLiant 1600 2-26
spares part number 1-3
Power supply
rear panel, spares part number 1-3
removing and replacing 2-33
spares part number 1-3
specifications 5-3
Power switch
removing and replacing 2-18
spares part number 1-3
Power-On Self-Test (POST)
description 3-4
error messages 3-4 to 3-16
Preparation procedures 2-2
Processor
board
dual SCSI, spares part number 1-3
without processor, spares part
number 1-3
cage, removing and replacing 2-20
components
ProLiant 1200 4-4
ProLiant 1600 4-1
power module
removing and replacing 2-26
spares part number 1-3
removing and replacing
ProLiant 1200 2-25
ProLiant 1600 2-24
with heatsink, spares part number 1-3
R
Rack
S
Safety warnings 2-4
SCSI
fixed disk drive, test error codes 3-28
tape drive, test error codes 3-29
Slide rail, spares part number 1-4
SmartStart and Support Software
CD-ROM 2-1, 3-2
Spares Parts List 1-3
Specifications
CD-ROM drive 5-6
DIMMs 5-4
diskette drive 5-5
power supply
ProLiant 1200 5-4
ProLiant 1600 5-3
system unit 5-2
Static electricity 2-1
Switch settings 4-9
Symbols in equipment 2-2
System Configuration Utility 2-1, 3-2
System I/O board
cage, removing and replacing 2-16
components 4-7
rear connectors 4-8
spares part number 1-3
system maintenance switch 4-9
System unit, specifications 5-2
T
Terminator board
removing and replacing 2-23
spares part number 1-3
Compaq ProLiant 1600 and ProLiant 1200 Servers Maintenance and Service Guide
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . .
I-4
Index
Top cover
removing and replacing 2-8
spares part number 1-3
U
Utilities 3-2
V
Video monochrome board, test error
codes 3-22
W
Warnings
rack 2-3
safety 2-4
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement