Target 14483887, 14484166 Assembly Instructions Manual

windham
one door accent cabinet
style # WNCBNT1DBL (teal)
dpci # 249-16-0731
tcin # 14484166
style # WNCBNT1DWB (blue)
dpci # 249-17-0830
tcin # 53546448
style # WNCBNT1DRD (red)
dpci # 249-16-0730
tcin # 14484167
style # WNCBNT1DOV (overcast)
dpci # 249-16-4304
tcin # 50077027
style # WNCBNT1DBK (black)
dpci # 249-16-0734
tcin # 14484139
style # WNCBNT1DGY (gray)
dpci # 249-16-0735
tcin # 14483887
style # WNCBNT1DWH (shell)
dpci # 249-16-0733
tcin # 14484164
style # WNCBNT1DPK (blush)
dpci # 249-17-0828
tcin # 53546442
style # WNCBNT1DSG (green)
dpci # 249-17-0829
tcin # 53546447
>> assembly instructions
© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your
room in no time. Good luck—though we’re confident you won’t need it.
before you begin
1.
2.
3.
4.
Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
Use the carton as a working surface to prevent product damage during assembly.
Read through and review assembly steps.
Gather all tools prior to assembly.
tools needed
2
table of contents
introduction
hardware
parts list
how to use the cam lock system
assembly
2
4
5
6
7-14
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and dpci number ready when calling.
3
hardware
4
(H1) x 8
wooden dowel
(H2) x 4
cam bolt
(H3) x 4
cam
(H4) x 15
short pan-head screw
(H5) x 4
short flat-head screw
(H6) x 4
shelf support
(H7) x 1
knob
(H8) x 1
knob bolt
(H9) x 4
allen head bolt
(H10) x 1
magnet
(H11) x 1
wall screw
(H12) x 1
wall anchor
(H13) x 1
wall strap
(H14) x 1
long pan-head screw
(H15) x 4
lock washer
(H16) x 6
washer
(H17) x 1
allen wrench
exploded diagram
ITEM
DESCRIPTION QUANTITY
1
top panel
1
2
left side frame
1
3
right side frame
1
4
bottom panel
1
5
shelf panel
1
6
door
1
7
back panel
1
5
how to use the cam lock system
2.
1.
Screw cam bolt into panel
3.
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
4.
6
Rotate cam(s) clockwise 180° to
lock panels together
Push cam into panel - arrow feature
on cam top points to panel edge
5.
Panels should be tight against each
other and connection should be rigid
step 1: attach right side frame to bottom panel
(H1) x 2
(H2) x 2
wooden dowel cam bolt
(H3) x 2
cam
1.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
1.2. Screw-In cam bolts must be screwed down flush.
1.3. Refer to page 6 for instructions on how to use the cam lock system.
7
step 2: attach left side frame
(H1) x 2
(H2) x 2
wooden dowel cam bolt
(H3) x 2
cam
2.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
2.2. Screw-In cam bolts must be screwed down flush.
2.3. Refer to page 6 for instructions on how to use the cam lock system.
8
step 3: attach magnet then attach top panel
If planning to install the door
opening to the right, use right side
pre-drilled holes for magnet.
If planning to install the door,
opening to the left, use left
side pre-drilled holes for magnet.
(H9) x 4
(H1) x 4
(H4) x 2
wooden dowel short pan-head allen bolt
screw
door opens to the left
door opens to the right
(H10) x 1
magnet
(H15) x 4
lock washer
(H16) x 4
washer
(H17) x 1
allen wrench
3.1. Carefully tap small wooden dowels into place. Leave 1/2” of the dowels sticking out.
3.2. Align bolts with pre-drilled holes.
3.3. Do not over tighten bolts or screws.
9
step 4: attach back panel
**FAILURE TO FOLLOW ALL DIRECTIONS ON THIS PAGE MAY RESULT IN UNEVEN DOOR ALIGNMENT**
hole for anti-tip strap
pre-drilled holes
Begin by installing all of the screws along one
edge of the back panel. Next, using a square
or tape measure, make sure that the cabinet is
square. (If using a tape measure, the distance
from one corner, diagonally to the other corner
should be the same in both directions.) If not,
apply gentle pressure to the diagonally opposite
corners to shift case into alignment. Re-measure
to ensure equal distances. Install the remaining
screws, starting with the corners.
(H4) x 13
short pan-head screw
4.1. Make sure the screws go through the pre-drilled holes properly.
4.2. Do not over tighten screws.
10
step 5: attach knob to door
(H7) x 1
knob
(H8) x 1
knob bolt
5.1. Align bolt with pre-drilled hole.
5.2. Do not over tighten bolt.
11
step 6: attach door
If planning to install the door
opening to the right, use right
side pre-drilled holes for hinges.
If planning to install the door,
opening to the left, use left
side pre-drilled holes for hinges.
(H5) x 4
short flat-head screw
6.1. Align screws with pre-drilled holes.
6.2. Do not over tighten screws.
12
step 7: install shelf panel
(H6) x 4
shelf support
7.1. Insert shelf supports into desired hole. Different holes accomodate different shelf heights.
7.2. Angle shelves to fit between the rails and set on top of shelf supports.
13
step 8: install anti-tip kit
(H16)
(H13)
Position against wall
(H14)
(H12)
Mark position of strap hole on
wall
Drill 1/4’’ hole
Tap in wall anchor
Fasten anti-tip strap
with flat-head screw provided
(H13) x 1
(H14) x 1
long pan head screw wall strap
14
(H16) x 2
washer
(H12) x 1
wall anchor
(H11) x 1
wall screw
(H11)
(H16)
WARNING
Serious or fatal crushing injuries can occur
from furniture tip-over. To help prevent
tip-over:
50 lb
s.
• Install tip-over restraint provided.
• Place heaviest items in the lowest drawers.
• Do not set TV's or other heavy objects on top
of this product, unless the product is
specifically designed to accommodate them.
• Never allow children to climb or hang on drawers,
doors, or shelves.
• Never open more than one drawer at a time.
(OR)
• Do not defeat or remove the drawer interlock
system .
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
This is a permanent label. Do not remove.
inner
shelf
weig
ht lim
it is 2
5 lbs
.
1. This unit has been designed for the weight shown. Exceeding this recommended weight could result in
excessive “sagging” of the top. Extreme overloading can cause failure of the top and possible injury.
2. Furniture Care Instructions: Dust with a clean, lint-free cloth. Use a spray furniture polish as needed.
QUESTIONS? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
15
© 2019 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.