SAMSUNG CLP 500 - CARTRIDGE REMANUFACTURING

SAMSUNG CLP 500 - CARTRIDGE REMANUFACTURING
AbsoluteCOLOR® • AbsoluteBLACK® • UniDrums • UniRollers • UniParts • UniCoatings
SAMSUNG CLP 500 - CARTRIDGE REMANUFACTURING INSTRUCTIONS
INCLUDING CARTRIDGE RESET SYSTEM FUSE INSTRUCTIONS
SAMSUNG CLP 500
COLOR LASER PRINTER
TONER CARTRIDGE
PAGE 2
www.uninetimaging.com
CARTRIDGE RESET SYSTEM INSTRUCTIONS
PAGE 4
USA
Ph: +310-280-9620
Fx: +310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
JAPAN
+81-3-44-55-2789
+310-838-7294
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
UNINET IMAGING INC. • SAMSUNG CLP 500 REMANUFACTURING INSTRUCTIONS
2
1
5
4
TABS
3
1. Remove the outer shell by first removing FIVE screws: FOUR
screws are located on the top of the cartridge as shown.
2. The FIFTH screw is located on the gear-side of the cartridge.
After removing the screws, unlock the bottom side of the shell by
pushing in the TABS shown using a flat-head screw driver.
3. Remove the cover as shown. You will notice a small adhesive
holding it in place, but it will not be affected if the cover is
removed.
REMOVING THE DEVELOPER ROLLER
4. Using a small flat-head screwdriver, remove the locking metal
CLIP located at each end of the developer roller axle. This clip
holds the axle gear in place. Push the clip out away from the axle
as shown.
NOTES:
www.uninetimaging.com
USA
Ph: +310-280-9620
Fx: +310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
JAPAN
+81-3-44-55-2789
+310-838-7294
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
UNINET IMAGING INC. • SAMSUNG CLP 500 REMANUFACTURING INSTRUCTIONS
5. Slide the developer roller gear off as shown.
6. Remove the locking metal clip and gear from the opposite end
of the axle in the same manner as in Step 4 and 5.
7. Using a small flat-head screwdriver, push out the metal washer-like ring that holds the axle in place near the toner fill plug
area. The other side should remain in place.
8. Slip the developer roller outward then slide it away toward the
side of the cartridge.
NOTES:
www.uninetimaging.com
USA
Ph: +310-280-9620
Fx: +310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
JAPAN
+81-3-44-55-2789
+310-838-7294
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
UNINET IMAGING INC. • SAMSUNG CLP 500 REMANUFACTURING INSTRUCTIONS
9. Remove the toner fill plug to begin the cleaning process. Use
a vacuum on easy areas making sure there is nothing that will
vent. Use air pressure for hard-to-reach and sensitive areas.
10. After thoroughly cleaning the cartridge and installing clean
components, you are now ready to install your after-market toner.
REPLACING THE CARTRIDGE RESET SYSTEM FUSE
Samsung CLP 500, 550 Smartchip BK/C/M/Y Fuse
(Uninet part #8172)
11. Locate the CONTACT ASSEMBLY on the gearless side of the
cartridge. Using a small flat-head screwdriver, carefully pry loose
the cartridge contacts assembly as shown.
NOTE: Electrical soldering is required for this section.
NOTES:
www.uninetimaging.com
USA
Ph: +310-280-9620
Fx: +310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
JAPAN
+81-3-44-55-2789
+310-838-7294
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
UNINET IMAGING INC. • SAMSUNG CLP 500 REMANUFACTURING INSTRUCTIONS
Remove
12. Locate the FUSE that is soldered to the two outer contact
tabs.
13. Use pliers to hold the FUSE while applying the heated solder
iron to the tab connected to it as shown. Carefully remove the
wire as the solder melts. Repeat the same on the other tab. DO
NOT OVERHEAT the tab as this may cause the housing to melt.
14. Use the solder iron to smooth out any solder material remaining on the outer contact tabs.
15. Solder the CARTRIDGE RESET SYSTEM FUSE onto the outer
contact tabs as shown. You can solder any side to either contact
as the tabs are not specific. Be careful not to overheat the tabs.
NOTES:
www.uninetimaging.com
USA
Ph: +310-280-9620
Fx: +310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
JAPAN
+81-3-44-55-2789
+310-838-7294
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
UNINET IMAGING INC. • SAMSUNG CLP 500 REMANUFACTURING INSTRUCTIONS
16. Insert the completed assembly back into the cartridge by lining up the tabs with the holes shown.
17. With the tabs in place, the assembly is now locked.
NOTES:
TESTING THE CARTRIDGE
18. Make sure the printer is turned OFF before installing and
testing the cartridge.
www.uninetimaging.com
USA
Ph: +310-280-9620
Fx: +310-838-7294
EUROPE
+34-93-757-1335
+34-93-741-4166
JAPAN
+81-3-44-55-2789
+310-838-7294
BRAZIL
+55-11-4822-3033
+55-11-4822-3353
ARGENTINA
+54-11-4571-2388
+54-11-4574-3706
11124 Washington Blvd., Culver City, California U.S.A. 90232 Ph: 310 280-9620 • Fx: 310 838-7294 • [email protected]
© 2006 Uninet Imaging Inc. All Trademark names are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
Uninet Imaging does not guarantee or warrant downloaded information.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement