Schneider Electric Sedna - Connected Universal Push-button Dimmer LED - Device User Guide

Add to My manuals
31 Pages

advertisement

Schneider Electric Sedna - Connected Universal Push-button Dimmer LED - Device User Guide | Manualzz

Sedna - Connected Universal Push-button

Dimmer LED

Device user guide

Information about features and functionality of the devices

02/2023

www.se.com

Legal Information

The Schneider Electric brand and any trademarks of Schneider Electric SE and its subsidiaries referred to in this guide are the property of Schneider Electric SE or its subsidiaries. All other brands may be trademarks of their respective owners.

This guide and its content are protected under applicable copyright laws and furnished for informational use only. No part of this guide may be reproduced or transmitted in any form or by any means (electronic, mechanical, photocopying, recording, or otherwise), for any purpose, without the prior written permission of

Schneider Electric.

Schneider Electric does not grant any right or license for commercial use of the guide or its content, except for a non-exclusive and personal license to consult it on an "as is" basis. Schneider Electric products and equipment should be installed, operated, serviced, and maintained only by qualified personnel.

As standards, specifications, and designs change from time to time, information contained in this guide may be subject to change without notice.

To the extent permitted by applicable law, no responsibility or liability is assumed by

Schneider Electric and its subsidiaries for any errors or omissions in the informational content of this material or consequences arising out of or resulting from the use of the information contained herein.

Table of Contents

Safety information

.......................................................................................4

Sedna - Connected Universal Push-button Dimmer LED

.....................5

For your safety ...........................................................................................5

About the device.........................................................................................6

Installing the device ....................................................................................6

Pairing the device .......................................................................................6

Pairing device manually.........................................................................7

Pairing device with auto scan.................................................................9

Configuring the device ..............................................................................10

Changing the device icon ....................................................................10

Renaming the device .......................................................................... 11

Changing the device location ............................................................... 11

Dimmer settings..................................................................................13

Removing the device ................................................................................16

Resetting the device .................................................................................17

Using the device .......................................................................................17

Switching/Dimming the device manually ...............................................18

Switching/Dimming the device using app ..............................................19

Creating a schedule ............................................................................20

Creating a moment .............................................................................21

Creating an automation .......................................................................23

LED Indication..........................................................................................27

Troubleshooting .......................................................................................28

Technical Data .........................................................................................28

DUG_Sedna Push-button Dimmer_WSE-00 3

4

Safety information

Safety information

Important information

Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it. The following special messages may appear throughout this manual or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

The addition of either symbol to a “Danger” or “Warning” safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that accompany this symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

Failure to follow these instructions will result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE

NOTICE is used to address practices not related to physical injury.

DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

Sedna - Connected Universal Push-button Dimmer

LED

SDD1xx381

For your safety

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

Safe electrical installation must be carried out only by skilled professionals.

Skilled professionals must prove profound knowledge in the following areas:

- Connecting to installation networks.

- Connecting several electrical devices.

- Laying electric cables.

- Safety standards, local wiring rules and regulations.

Failure to follow these instructions will result in death or serious injury.

DANGER

RISK OF FATAL INJURY FROM ELECTRIC SHOCK

The output may carry electric current even when the load is switched Off.

Disconnect the device from the supply by means of the fuse in the incoming circuit before working on the device.

Failure to follow these instructions will result in death or serious injury.

CAUTION

THE DEVICE MAY BE DAMAGED

Only connect dimmable load.

Failure to follow these instructions can result in injury or equipment damage.

DUG_Sedna Push-button Dimmer_WSE-00 5

Sedna - Connected Universal Push-button Dimmer LED

About the device

The Connected Multiwire Universal Push-button Dimmer LED (hereinafter referred to as Dimmer ) is a push-button device that can be used to switch and dim LED, ohmic, inductive or capacitive loads manually or remotely. It can detect the load automatically and provides thermal protection, overload-resistance and shortcircuit protection.

Control options

Home control : To control the dimmer through the Wiser app you will need the

Wiser Gateway.

Direct operation : The dimmer can always be controlled directly on-site. You can also connect any number of mechanical push-buttons to control the device.

Installing the device

Refer to the installation instruction supplied with this product.

See Connected Universal Push-button Dimmer LED .

Pairing the device

Using the Wiser app, first pair your device with the Gateway / Hub to access and control the device. You can either add the device manually or do an auto-scan to pair it.

6 DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

Pairing device manually

To pair the device manually:

1. On Home page, tap + .

2. Tap and select the required Wiser Hub on the slide-up menu.

3. Select an option to add the device (A):

– Add Device with Install Code

– Add Device without Install Code

Add Device

Install Code is Recommended device.

If you are unable to scan or type the install code, you can still add the device without it.

Add Device without Install Code

A

TIP: It is highly recommended to add the device with install code.

4. To pair the device with install code, tap Add Device with Install Code to display the slide-up menu. Select any one of the options (B):

– Scan Install Code - you can scan the device for the install code

– Enter Install Code Manually - you can manually enter the install code from the device

TIP: Install code is located on the rear side of the device.

After pairing the device with install code, proceed to Step 6 .

B

Cancel

5. To pair the device without install code, tap Add Device without Install Code .

DUG_Sedna Push-button Dimmer_WSE-00 7

8

Sedna - Connected Universal Push-button Dimmer LED

6. Short press upper part of the push-button 3 times (< 0,5 s).

3× < 0,5 s

The LED blinks amber.

7. In the app, select Confirm LED is blinking amber and tap Start configuration (C).

Cancel

How to pair device

Short-press upper part of switch 3 times.

3

C

After a few seconds, a solid green LED indicates that the device is successfully paired to the Gateway/Hub.

8. Once the device is added in the app, tap Done .

DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

Pairing device with auto scan

Pairing the device with auto scan automatically discovers the device when the corresponding device is powered on.

1. On the Home page, tap + .

2. Tap Auto scan > Confirm .

3. Enable permissions to Access location and Wi-Fi for scanning device and tap Start scanning .

NOTE: If you have multiple hubs, do Step 4 or proceed to Step 5.

4. Tap Select hub and select the Wiser hub from the slide-up menu.

5. Short press upper part of the push button 3 times (< 0,5 s) and wait for a few seconds until the device search is complete.

The LED blinks amber.

TIP: If you want to pair multiple devices at once, perform step 5 on each device and wait for a few seconds for them to be detected.

6. Tap Next (A) and select Push Button Dimmer .

Auto Scan

Push Button

Next

A

7. Once the device is added successfully, tap Done .

DUG_Sedna Push-button Dimmer_WSE-00 9

Sedna - Connected Universal Push-button Dimmer LED

Configuring the device

Changing the device icon

You can change the device icon using the Wiser app.

1. On the Home page, select the device for which you wish to change the icon.

2. At the top-right corner of the screen, tap .

3. Tap edit next to the device name.

4. Tap Icon to view the menu.

5. In the slide-up menu, select any one of the following (A) to change the device icon:

– Take photo - allows you to click a photo from the mobile camera.

– Select from Icon Library - allows you to select an icon from the app library.

– Select from Album - allows you to select a photo from the mobile gallery.

Icon

Name

Location

Take photo

Select from Icon Library

Select from album

Cancel

A

10 DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

Renaming the device

You can rename the device using the Wiser app.

1. On the Home page, select the device for which you wish to rename.

2. At the top-right corner of the screen, tap .

3. Tap edit next to the device name.

4. Tap Name , enter the new name (A) and then tap Save .

Icon

Name

Location

Cancel

Rename

Save

A

Changing the device location

You can change the device location using the Wiser app.

1. On the Home page, select the device for which you wish to change the location.

2. At the top-right corner of the screen, tap .

3. Tap edit next to the device name.

4. Tap Location .

5. Select the desired location from the list (A) and then tap Save .

Device location

Living Room

Master Bedroom

Kitchen

Dining Room

Study Room

Kids Room

Save

A

DUG_Sedna Push-button Dimmer_WSE-00 11

Sedna - Connected Universal Push-button Dimmer LED

Dimmer settings

Using The Wiser app, you can manage the Dimmer modes and settings.

To access the dimmer settings:

1. On the Home page, tap All devices > Push Button Dimmer .

2. On the device control panel page, tap Settings .

Dimming mode

You can change the dimming mode in the app if you have problems with light flickering. This improves the dimming quality.

Tap Dimming Mode (A) and select either of the following:

– Auto - When any other load is connected to the dimmer (e.g. filament bulb).

– Leading Edge - When a LED is connected to the dimmer. Only choose this mode if the LED is not working properly in Auto mode

NOTE: This mode uses 10 % of the nominal load to avoid overheating of the

Dimmer, refer to

technical data, page 28 .

A

Auto

DUG_Sedna Push-button Dimmer_WSE-00 13

Dimming range

Sedna - Connected Universal Push-button Dimmer LED

You can restrict the maximum and minimum brightness of the load connected to the device. This is done to avoid flickering and switching off the LED.

Tap Dimming Range (B) and do either or both of the following:

– Min Brightness - Drag the sliding bar to restrict the minimum brightness.

TIP: If you set the minimum brightness to the right most position on this sliding bar, then the load glows at the minimum brightness even if you drag the sliding bar to the lowest value in the

control panel, page 17 .

– Max Brightness - Drag the sliding bar to restrict the maximum brightness.

TIP: If you set the maximum brightness to the left most position on this sliding bar, then the load glows at the maximum brightness even if you drag the sliding bar to the highest value in the

control panel, page 17 .

14 DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

LED indicator mode

You can select the LED indicator mode for easy identification of the device status.

Tap Backlight Mode (C) and select any one of the following:

– Reverse With Load - The LED on the dimmer is On when the connected load is

Off.

– Consistent With Load - The LED on the dimmer is On when the connected load is On.

– Always Off - The LED on the dimmer is always Off.

– Always On - The LED on the dimmer is always On.

For information on LED color during each modes, refer to

LED indication, page 27

.

DUG_Sedna Push-button Dimmer_WSE-00 15

Sedna - Connected Universal Push-button Dimmer LED

Toggle mode setting

Using this setting, the device will remember the last state of the device.

Tap Toggle Mode Setting (D) and select any one of the following:

– 100% - The LED glows at maximum brightness every time it is turned on.

– Last Level (Memory Function) - The LED glows at the previously set brightness level whenever it is turned on.

Removing the device

Using the Wiser app, you can remove a device from the device list.

1. On the Home page, tap All devices > Push-button Dimmer .

2. Tap to display more details.

3. Tap Remove and Factory Reset Device (A).

More

Push-button Dimmer

Moment and Automation

Others

Add to home Screen

A

TIP: Alternatively, you can tap and hold the Push-button Dimmer on the

Home page to remove the device.

NOTE: By removing the device, you will reset the device. If you still have a problem with the reset, then refer to

resetting the device, page 17 .

16 DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

Resetting the device

You can reset the device to factory default manually.

Short press push button 3 times (< 0.5 s) and then long press the push button once (>10 s). after 10 s, LED starts blinking red then release the push button.

The LED stops blinking upon successful reset of the device.

The Push-button Dimmer restarts and blinks green for a few seconds.

NOTE: After reset, the LED turns amber indicating that it is ready for pairing.

3× < 0,5 s

Using the device

The Control Panel allows you to switch the Dimmer on/off, increase/decrease the brightness and control various settings.

On the Home page, tap All devices > Push Button Dimmer to access the control panel.

On the control panel page, you can see the following:

• The current state of the Dimmer (A)

• Sliding bar to adjust the brightness (B)

• The current brightness percentage (C)

Schedule, page 20

(D)

Settings, page 13

(E)

Push-button Dimmer

C

D

E

A

On

50%

B

DUG_Sedna Push-button Dimmer_WSE-00 17

Sedna - Connected Universal Push-button Dimmer LED

Switching/Dimming the device manually

You can turn on/off and increase/decrease the brightness of the dimmer manually.

The dimmer will provide power to the load connected to it.

Short press the push-button (< 0,5 s) once to switch on/off the dimmer.

< 0,5 s

Long press the push-button (> 0,5 s) on the device to increase/decrease the brightness of the dimmer.

> 0,5 s

18 DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

Switching/Dimming the device using app

Using the Wiser app, you can switch on/off and increase/decrease the brightness of the device.

Switch On/Off the device

1. On the Home page, tap the power button (A) to switch on/off the Dimmer.

2. Alternatively, you can navigate to the control panel of the device and tap icon to switch on/off the Dimmer.

NOTE: The control panel shows the current state of the Dimmer.

Adjusting the brightness of the device

To increase/decrease the brightness of the device:

1. In home page, next to device name,, tap ˅ (B) for common function and drag the slider to adjust the brightness of the Dimmer.

2. Alternatively. you can navigate to the control panel of the device and drag the sliding bar up/down to increase/decrease the brightness.

NOTE: The control panel shows the current brightness percentage of the

Dimmer.

DUG_Sedna Push-button Dimmer_WSE-00 19

Sedna - Connected Universal Push-button Dimmer LED

Creating a schedule

Using a schedule, you can control and trigger the dimmer. The system will follow the active schedule once it has been set. You can create or modify schedules at any time.

1. On the Home page, tap All devices > Push-button Dimmer .

2. Tap Schedule > Add schedule to add a schedule.

3. Set the time (A).

4. Tap Repeat (B) to select the days you want to set the schedule.

5. Tap Note (C), enter the note and tap Confirm .

6. Tap the toggle switch (D) to turn on the Notification for the schedule. The app will send a notification when the task is executed at the time of schedule.

7. In the Push-button Dimmer section, drag the sliding bar (E) to do one of the following:

– 100% : turns on the dimmer with maximum brightness on the scheduled time.

– Off : turns off the dimmer on the scheduled time.

– Drag the sliding bar anywhere in between to turn on the dimmer with a set brightness level on the scheduled time

Cancel Add Schedule

08 20

09 21

10 22 AM

11 23 PM

24

25

B

C

Repeat

Note

Save

Once

A

D

50% 100%

E

8. Tap Save .

20 DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

Creating a moment

A Moment allows you to group multiple actions that are usually done together.

Using the Wiser app, you can create moments based on your needs (such as movie night).

To create a moment:

1. On the Home page, tap .

2. Go to Moment > + to create a moment.

3. Tap Edit name , enter the name of the moment (A) and tap Save .

TIP : You can choose the cover image that represents your moment by tapping .

Edit name

A

Cancel

Edit name

Add Task

Save

4. In the Action section, tap Add task (B) to display the slide-up menu.

5. In the Add task menu, you can do either or all of the following actions (C):

– Run the device : select the devices that you want in a moment.

– Select Automation : select the automation that you want to enable or disable. For more info refer to

Automation, page 23 .

– Delay : set the delay time.

NOTE : You can add one or more actions using .

My settings

Show on Home Page

Add task

Select Automation

Delay

B

C

DUG_Sedna Push-button Dimmer_WSE-00 21

Sedna - Connected Universal Push-button Dimmer LED

6. Tap Run the device > Push-button Dimmer and select either or both the functions to add in the moment:

– Dimmer : turn the Dimmer on/off (D).

– Brightness : adjust the brightness level (E).

Select function Next

D

E

7. Once all the actions are set, tap Save .

Cancel Moment Settings Save

My Moment

Action (2/80)

Show on Home Page

Editing a moment

To edit a moment:

1. On the Moment tab, locate the moment you want to edit and tap .

2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings.

TIP:

• You can add one or more actions using .

• To delete an existing action, slide the each item towards left and tap

Delete .

Deleting a moment

To delete a moment:

1. On the Moment tab, locate the moment that you want to delete and then tap

.

2. Tap Delete and tap Ok .

NOTE: After deleting a moment, the device action can no longer be triggered.

22 DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

Creating an automation

An automation allows you to group multiple actions that are usually done together, triggered automatically or at scheduled times. By using the Wiser app, you can create automations based on your needs.

1. On the Home page, tap .

2. Go to Automation > + to create an automation.

3. Tap Edit name , enter the name of the automation (A) and tap Save .

TIP : You can choose the cover image that represents your automation by tapping .

My Automation

A

Cancel

Add Condition

4. Tap Any condition is met to select any one of the condition type (B):

– All conditions are met : the automation is triggered when all the conditions are met.

– Any condition is met : the automation is triggered when at least one condition is met.

My Automation

Select Condition type

All conditions are met

Any condition is met

Cancel

B

5. Tap Add Condition to display the slide-up menu.

DUG_Sedna Push-button Dimmer_WSE-00 23

24

Sedna - Connected Universal Push-button Dimmer LED

6. In the Add Condition menu, you can do either or all of the following options

(C):

– When weather changes : select the various weather settings.

– Schedule : set the time and day.

– When device status changes : select the device and it’s function.

Note: You can add one or more conditions using .

My Automation

Schedule

Add Condition

C

7. Tap When device status changes > Push-button Dimmer and select either or both the functions:

– Dimmer : turn the Dimmer On/Off (D)

– Brightness : adjust the brightness level (E)

Select function

Next

D

E

8. Tap Add task to open the slide-up menu.

DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

9. In the Add task menu, you can do either or all of the following options (F):

– Run the device : select the devices that you want to trigger.

– Moment or Automation : select the moment which you want to trigger or select the automation that you want to enable or disable.

– Send notification : turn on notification for the automation.

– Delay : set the delay time.

NOTE : You can add one or more actions using .

My Automation

Action

Add task

(Added 0/80)

Moment or Automation

All-Day

F

10. Tap on Effective period to set the time range for the automation. You can select any one of the following (G):

– All-day : 24 hours

– Daytime : From sunrise to sunset

– Night : From sunset to sunrise

– Custom : User defined time period

Next

24 hours

From sunrise to sunset

G From sunset to sunrise

Custom

Repeat

City

11. Once all the actions and conditions are set, tap Save .

Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.

Example of an automation

This demonstration shows you how to create an automation to switch on the light with 50% brightness level when a motion is detected.

NOTE: The Dimmer will not be switched off automatically when the Sensor sends the "Unoccupied" message. To switch off the dimmer when there is no more motion, you must create a new automation.

1. Go to Automation > + to create an automation.

DUG_Sedna Push-button Dimmer_WSE-00 25

26

Sedna - Connected Universal Push-button Dimmer LED

2. Tap Edit name , enter the name of the automation and tap Save .

TIP : You can choose the cover image that represents your automation by tapping .

3. Tap Add Condition > When device status changes > Motion Sensor .

4. Tap Motion State > Occupied (A).

A

Occupied

Unoccupied

Motion state

5. Tap Add task > Run the device > Push-button Dimmer .

6. Tap Brightness (B), adjust the brightness to 50% and tap Save .

TIP: Setting the brightness level turns on the light the light when the automation is triggered. You need not add a task to turn on the Dimmer separately.

7. Tap Next .

DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

8. In the Automation Settings page, tap Save .

Once the automation is saved, it is visible on the Automation tab. You can tap the toggle switch on the automation to enable it.

Editing an automation

To edit an automation:

1. On the Automation tab, locate the automation you want to edit and tap .

2. On the Edit page, you can tap each item (such as dimmer, shutter, delay, temperature, etc.) to change the settings.

TIP:

• You can add one or more actions using .

• To delete an existing condition or action, slide each item towards left and tap Delete .

Deleting an automation

To delete an automation:

1. On the Automation tab, locate the automation that you want to delete and then tap .

2. Tap Delete and tap Ok .

NOTE: After deleting an automation, the device action can no longer be triggered.

LED Indication

Pairing

User Action

Press the push-button 3 times

LED Indication

LED blinks amber per second.

Status

Pairing mode is active for 30 seconds.

When pairing is completed, LED glows green for some time before turning off.

DUG_Sedna Push-button Dimmer_WSE-00 27

Resetting

User Action

Press the push-button 3 times and hold it down once for > 10 s.

LED Indication

After 10 s, the LED blinks red.

Sedna - Connected Universal Push-button Dimmer LED

Status

The device is in reset mode. It is reset to the factory settings after 10 seconds. The device then restarts and the LED blinks green for a few seconds and then stays amber.

LED Indicator Mode/Backlight Mode

Load Status ON

Reverse with load No LED

Consistent with load

Always Off

Always On

No LED

OFF

No LED

No LED

Troubleshooting

Symptom

Dimming up not possible.

Switching On not possible.

Flickering at minimum brightness.

Flickering

Only slight dimming capability

The device is not ready to pair after the device is removed from the app.

Solution

• Reduce/increase load.

• Allow the Dimmer to cool in case of overheating.

• Change the load (if the load is incompatible with the Dimmer).

• Allow the Dimmer to cool in case of overheating.

• Reduce load.

• Change load.

• Check wiring between the push button and the Dimmer.

• Increase minimum brightness (if flickering still persists, install a 31LCDA load correction device).

• Change the load (if the minimum brightness is insufficient).

• Set to RL LED mode.

• Change load.

• Set to RL LED mode.

• Change dimming range.

• Set to RL LED mode.

• Change the load (if the load is incompatible with the Dimmer).

Reset to factory default settings, refer to

reset the device, page 17 .

Technical Data

Nominal voltage

Nominal power

AC 230 V ~, 50 Hz

Load type

LED

Load name

LED

Load value

7–100 VA

7–20 VA

RC

RL

28 DUG_Sedna Push-button Dimmer_WSE-00

Sedna - Connected Universal Push-button Dimmer LED

Iron core transformer

Incandescent lamp

Halogen lamp

Electronic step-down converter

Standby

Neutral conductor

Connecting Terminals

Extension unit

Fuse protection

Operating frequency

Max. radio-frequency power transmitted

Communication protocol

Max 0.4 W

Not required

Screw terminals for max. 2 x 2.5 mm², 0.5 Nm

Single Push-button, unlimited number, max. 50 m

16 A circuit breaker

2405 - 2480 MHz

< 10 mW

Zigbee 3.0 certified

14–150 VA

RL

14–200 W

R

14–150 W

R

14–150 VA

RC

DUG_Sedna Push-button Dimmer_WSE-00 29

Compliance

Compliance information for Green Premium products

Find and download comprehensive information about Green Premium products, including RoHS compliance and REACH declarations as well as Product

Environmental Profile (PEP) and End-of-Life instructions (EOLI).

General information about Green Premium products

Click the link below to read about Schneider Electric’s Green Premium product strategy.

https://www.schneider-electric.com/en/work/support/green-premium/

Find compliance information for a Green Premium product

Click the link below to search for a product’s compliance information (RoHS, REACH,

PEP and EOLI).

NOTE: You will need the product reference number or product range to perform the search.

https://www.reach.schneider-electric.com/CheckProduct.aspx?cskey= ot7n66yt63o1xblflyfj

Trademarks

This guide makes reference to system and brand names that are trademarks of their relevant owners.

• Zigbee ® is a registered trademark of the Connectivity Standards Alliance.

• Apple ® and App Store ® are brand names or registered trademarks of Apple Inc.

• Google Play™ Store and Android™ are brand names or registered trademarks of Google Inc.

• Wi-Fi ® is a registered trademark of Wi-Fi Alliance ® .

• Wiser™ is a trademark and the property of Schneider Electric, its subsidiaries and affiliated companies.

Other brands and registered trademarks are the property of their respective owners.

Schneider Electric

35 rue Joseph Monier

92500 Rueil Malmaison

France

+ 33 (0) 1 41 29 70 00 www.se.com

As standards, specifications, and design change from time to time, please ask for confirmation of the information given in this publication.

© 2023 – 2023 Schneider Electric . All rights reserved.

DUG_Sedna Push-button Dimmer_WSE-00

advertisement

Related manuals