Clayton WGX-215G-1 Operation & Maintenance Manual

Safety – Operation – Maintenance
Keep this document in a safe place
Read and understand this manual before operating your air tool
WartHog WGX Power Head
Electric HEPA Industrial Vacuum
Models: WGX‑107G‑0, WGX‑107G‑1, WGX‑115G‑0,WGX‑115G‑1, WGX‑205G‑0, WGX‑205G‑1, WGX‑215G‑0, WGX‑215G‑1
• Designed for general cleanup and housekeeping
• Dry Recovery Only
Scan this QR code for
online instructions and
documentation, or visit
www.ClaytonHowTo.com
WGX-0_cover
WARNING
SAFETY LEGEND
WARNING
Read and understand operator’s manual before
using this equipment.
WARNING
Hearing protection is recommended when
operating this equipment.
WARNING
Eye protection is required when operating this
equipment.
WARNING
Respiratory protection is recommended
operating this equipment.
• A HEPA Filter must be installed in this vacuum at all times.
• If this vacuum is used to collect hazardous material, appropriate personal protective equipment may be required.
• Any alteration to this equipment by a third party will nullify its warranty.
WGX-0
October 06, 2022
TABLE OF CONTENTS
Important Safety Instructions................................................................................................3
Applications & Environments................................................................................................4
What’s In the Box.................................................................................................................4
Specifications & Requirements............................................................................................4
Getting Started.....................................................................................................................5
Before Each Use..................................................................................................................7
Bag Filter Change................................................................................................................7
Pre‑Filter Change.................................................................................................................8
HEPA Filter Change..............................................................................................................9
Illustrated Parts Breakdown...............................................................................................10
Limited Lifetime Warranty Terms And Conditions...............................................................14
EC Declaration of Conformity.............................................................................................15
Repair or Warranty Contact
WGX-0
Page 2
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
When using an electrical appliance, basic precautions should always be followed, including the following:
WARNING
To reduce the risk of fire, electric shock, or injury:
• Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing.
• This unit is to be used only indoors and in a dry location.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors,
or dropped into water, return it to a service center.
• Handle provided on power head is used only for removal of power head during maintenance.
• Before separation of power head from tank, users must disengage draw latches on tank.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners.
• Do not run appliance over cord. Keep cord away from heated surfaces.
• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
• Do not handle plug or appliance with wet hands.
• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may
reduce air flow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Turn off all controls before unplugging.
• Do not use to pick up flammable or combustible liquids, such as gasoline, or use in areas where they may be present.
• Connect to a properly grounded outlet only. Refer to “EARTHING/GROUNDING INSTRUCTIONS” on page 3.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
• Do not use without all filters in place.
• Do not allow to be used as a toy. Close attention necessary when used by or near children.
• Use extra care when cleaning on stairs
SAVE THESE INSTRUCTIONS
EARTHING/GROUNDING INSTRUCTIONS
This appliance must be earthed/grounded. If it should malfunction or breakdown, earthing/grounding provides a path of least resistance
for electric current to reduce the risk of electric shock. This appliance is equipped with a cord having an equipment-earthing/grounding
conductor and earthing/grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and earthed/grounded in
accordance with all local codes and ordinances.
WARNING – Improper connection of the equipment-earthing/grounding conductor can result in a risk of electric shock. Check with a qualified
electrician or service person if you are in doubt as to whether the outlet is properly earthed/grounded. Do not modify the plug provided with the
appliance – if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
Refer to Name Plate for electrical requirements.
• USA 120 V
This appliance has a earthing/grounding attachment plug that looks like the
plug illustrated in Figure 1. Make sure that the appliance is connected to an
outlet having the same configuration as the plug. No adapter should be used
with this appliance.
• International 120 V
This appliance has an IEC 60309 120 V earthing/grounding attachment plug.
Make sure that the appliance is connected to an outlet having the same
configuration as the plug. No adapter should be used with this appliance.
• International 220 V – 240 V
This appliance has an IEC 60309 250 V earthing/grounding attachment plug.
Make sure that the appliance is connected to an outlet having the same
configuration as the plug. No adapter should be used with this appliance.
Repair or Warranty Contact
WGX-0
Grounded Outlet
GL_002
Grounded
Outlet Box
Grounding Pin
Figure 1: Earthed/Grounded Outlet and Plug
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
Page 3
APPLICATIONS & ENVIRONMENTS
• Designed for general cleanup and housekeeping.
• Dry recovery only.
Do not use this equipment for cleaning or extracting fuel residues from any vehicle or equipment.
Do not use this equipment for cleaning or extracting live sparks or burning embers.
Do not use this equipment in combustible dust or gas atmospheres.
WHAT’S IN THE BOX
WGX-0_001
WartHog WGX Power Head
NOTE:
Clayton vacuum tanks ship in their own box and include bags, filters, and other components. These instructions assume you have
both a power head and an appropriate Clayton vacuum tank. Refer to the instruction manual included with the vacuum tank for
additional information.
SPECIFICATIONS & REQUIREMENTS
PHYSICAL:
Weight.....................................................................................................................................................................................TBD lbs (TBD kg)
Dimensions (Diameter x Height)........................................................................................................................... 17.5 x 12 in (44.5 x 30.5 cm)
Sound Level............................................................................................................................................................................................ 67 dBA
POWER CONSUMPTION:
Power Rating...............................................................................................................................................................................................2 hp
Power Consumption............................................................................................................................................................... 12.5 A @ 120 Vac
7.5 A @ 220 – 240 Vac
FILTRATION:
HEPA Filter Efficiency................................................................................................................................................99.995% @ 0.3 μm (H14)
Filter Bag Efficiency.............................................................................................................................................................. 95% @ 0.5 micron
PERFORMANCE:
120 Vac
Vacuum Flow........................................................................................................................................................... 120 CFM (204 SCMH)
Vacuum Suction...........................................................................................................................................................120 inH2O (30 kPa)
220 – 240 Vac
Vacuum Flow........................................................................................................................................................... 115 CFM (196 SCMH)
Vacuum Suction.......................................................................................................................................................... 115 inH2O (29 kPa)
Repair or Warranty Contact
WGX-0
Page 4
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
GETTING STARTED
1. The vacuum power head and the vacuum tank ship in separate boxes.
2. Unbox the vacuum power head.
3. Visually inspect the power head to verify that no parts are missing or damaged.
4. Familiarize yourself with the power head.
Power Switch
Power Cord
WGX-0_002
HEPA Wire Lock
Hex Standoff
Filter Adapter
HEPA Wire Lock
Hex Standoff
5. Power Head Vents:
• NEVER BLOCK THE POWER HEAD VENTS.
• NEVER WRAP THE POWER CORD AROUND THE POWER HEAD VENTS.
Power Head
Vents
WGX-0_003
Repair or Warranty Contact
WGX-0
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
Page 5
GETTING STARTED
Prepare the vacuum for use.
1. Install a filter bag on the tank.
• Unfold and fluff a new filter bag.
• Push the inlet tube into the hole on the cardboard collar of the filter bag.
• Grasp the sides of the cardboard collar and push it all the way onto the inlet tube.
• Verify the bottom of the collar is past the opening on the underside of the inlet tube.
Tank Wall
Filter Bag
Bottom and top of
Cardboard Bag Collar
must be flush to tank
Tank Wall
GL_005
Push Cardboard Bag Collar
past this point
2. Unbox a new HEPA filter.
• Remove the Clayton HEPA timer card from the box and set aside.
• Remove the HEPA cable lock from the box and set aside.
• Remove the HEPA filter from the box and remove from plastic bag.
3. Install a new HEPA filter.
• Holding the power head on its side, screw the new HEPA filter onto the filter adapter.
• Verify the white inner ring of the HEPA filter is fully seated against the underside of the power head.
– If it is not, rotate it clockwise until fully seated.
• Refer to the instructions included with the HEPA cable lock to install the cable lock.
4. Attach the power head.
• Position the power head on the tank.
• Rotate the power head so that the power switch on the power head is aligned with
the inlet port on the vacuum tank.
• Latch the power head to the tank.
5. Activate the HEPA filter timer.
• Attach the new HEPA timer card with a zip tie (included) to the top handle of the
vacuum.
• Follow the directions on timer card to activate it.
Repair or Warranty Contact
WGX-0
Page 6
Power Switch …
aligned with …
WGX-0_004
Inlet Port
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
BEFORE EACH USE
1. Attach the vacuum hose.
• Open the Inlet Port on the vacuum tank.
• Insert the metal sleeve of the vacuum hose into the Inlet Port on the vacuum tank.
2. Plug the power head/vacuum into an appropriate outlet.
3. Activate the vacuum.
• Toggle the power switch to the ON position.
BAG FILTER CHANGE
If this vacuum is used to collect hazardous material, appropriate personal protective equipment may be required.
The bag filter should be replaced when ¾ full.
1. Safe the vacuum.
• Disconnect the vacuum from power source.
• Remove all hoses from the vacuum.
2. Remove the power head.
• Unlatch the power head from the tank.
• Lift the power head and the attached HEPA filter off the tank using the top handle.
• Carefully place the power head on the floor – avoid damaging the HEPA filter.
3. Remove the filter bag.
• Grasp the cardboard collar of the bag filter and slide it off the inlet port on the vacuum tank.
• Holding your hand over the opening on the bag, lift the bag out of the tank.
• Dispose of the bag according to company policy.
4. Install a new filter bag.
• Unfold and fluff a new filter bag.
• Push the inlet tube into the hole on the cardboard collar of the filter bag.
• Grasp the sides of the cardboard collar and push it all the way onto the inlet tube.
• Verify the bottom of the collar is past the opening on the underside of the inlet tube.
Tank Wall
Filter Bag
Bottom and top of
cardboard bag collar
must be flush to tank
Tank Wall
GL_005
Push cardboard bag
collar past this point
continued on next page
Repair or Warranty Contact
WGX-0
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
Page 7
BAG FILTER CHANGE
5. Verify the HEPA filter is seated.
• Holding the power head on its side, examine the HEPA Filter.
• Verify the white inner ring of the HEPA filter is fully seated against the underside of the power head.
– If it is not, rotate it clockwise until fully seated.
6. Replace the power head.
• Position the power head on the tank.
• Rotate the power head so that the power switch on the power head is aligned with the inlet port on the vacuum tank.
• Latch the power head to the tank.
PRE‑FILTER CHANGE
If this vacuum is used to collect hazardous material, appropriate personal protective equipment may be required.
Replace the pre‑filter every five (5) bag filter changes or when it becomes visibly dirty.
1. Safe the vacuum.
• Disconnect the vacuum from the power source.
• Remove all hoses from the vacuum.
2. Remove the power head.
• Unlatch the power head from the tank.
• Lift the power head and the attached HEPA filter off the tank using the top handle.
• Carefully place the power head on the floor – avoid damaging the HEPA filter.
3. Remove the pre‑filter.
• The pre‑filter is wrapped around the HEPA filter and secured with Velcro.
• Find the seam and carefully peel the Velcro apart.
• Dispose of the pre‑filter according to company policy.
4. Install a new pre‑filter.
• Unfold a new pre‑filter and remove the thin Velcro cover strip from the Velcro hooks.
• Wrap the pre‑filter tightly around the HEPA filter.
• Secure the pre‑filter by adhering the Velcro hooks to the side of the pre‑filter.
5. Verify the HEPA filter is seated.
• Holding the power head on its side, examine the HEPA Filter.
• Verify the white inner ring of the HEPA filter is fully seated against the underside of the power head.
– If it is not, rotate it clockwise until fully seated.
6. Replace the power head.
• Position the power head on the vacuum tank.
• Rotate the power head so that the power switch on the power head is aligned with the inlet port on the vacuum tank.
• Latch the power head to the tank.
Repair or Warranty Contact
WGX-0
Page 8
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
HEPA FILTER CHANGE
If this vacuum is used to collect hazardous material, appropriate personal protective equipment may be required.
The HEPA filter should be replaced when it is damaged, clogged, or when the HEPA timer card has reached 12 months. Never attempt to clean
the HEPA filter as this will damage it.
1. Safe the vacuum.
• Disconnect the vacuum from the power source.
• Remove all hoses from the vacuum.
2. Remove the power head.
• Unlatch the power head from the vacuum tank.
• Lift the power head and the attached HEPA filter off the tank using the top handle.
• Carefully place the power head on the floor – avoid damaging the HEPA filter.
3. Unbox a new HEPA filter.
• Remove the Clayton HEPA timer card from the box and set aside.
• Remove the HEPA cable lock from the box and set aside.
• Remove the HEPA filter from the box and remove it from the plastic bag.
4. Remove the old HEPA filter.
• Holding the power head on its side cut the HEPA cable lock and remove it.
• Unscrew the HEPA filter from the filter adapter.
• Dispose of the HEPA filter according to company policy.
5. Install a new HEPA Filter.
• Holding the power head on its side, screw the new HEPA filter onto the threaded filter adapter.
• Verify the white inner ring of the HEPA filter is fully seated against the underside of the power head.
– If it is not, rotate it clockwise until fully seated.
• Refer to the instructions included with the HEPA cable lock to install the cable lock.
6. Replace the power head.
• Carefully position the power head on the vacuum tank.
• Rotate the power head so that the power switch on the power head is aligned with the inlet port on the vacuum tank.
• Latch the power head to the vacuum tank.
7. Activate the HEPA filter timer.
• Remove the old HEPA timer card from the power head.
• Attach the new HEPA timer card with a zip tie (included) to the top handle of the vacuum.
• Follow the directions on the timer card to activate.
Repair or Warranty Contact
WGX-0
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
Page 9
Illustrated
Parts Breakdown
Illustrated
Parts
Breakdown
603‑WGX‑0/603‑WGX‑1 (Sheet 1 of 4)
Seq
1
2
3
4
5A
5B
6
7
8
9
10
11
12
13
14
15
16
Item No
350-023
605-310A
605-310D
605-311E
900-143N515P-30
900-153H000X-30
900-M14R3
900-M14S
900-SW-SPDT-01
930-027
FE103212-HZSM-Z
NE10320608-HNSZ
RE0620-SDSSS-Z
SE103206-XPSM-Z
WE133203-RFS-Z
WE481803-RZSZ
945-HSN08X2BK
Description
Gasket, Filter Adapter
HH Vac Head Handle Cap SS Black
HH Vac Head Exhaust Baffle SS Black
WGX Vac Enclosure Cleanup 120V SS Black
Cord 14/3 15A Cord Lock Plug 30ft Yel
Cord 1.5MM 3 Conductor H05VVF 30ft Black
Molex Receptacle, 14 ga, 3 Position
Molex Socket Terminal, 14 ga
Switch Rocker Rect 20A 120V SPDT On-Off-On Black
Handle, Carry, Flex Rubber
Hex Standoff, 10-32 MF x 3/4 in SS
Nut 10-32 Nylon Lock SS Short
Rivet Blind 3/16 x 0.625 Sealed SS (.251-.375)
Screw 10-32 x 3/8in SS TORX
Washer .203ID x .500OD .047H Round Stainless Steel
Shim .750 ID x 1.125 OD x .048 Round Stainless
Heat Shrink 2 to 1 for Power Cord
9
14
5B
12
For 220 V
13
16
2
6
10
7
5A
For 120 V
WGX-0_008
3
10
15
6
7
1
4
8
Repair or Warranty Contact
WGX-0
Page 10
11
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
Illustrated Parts Breakdown
603‑WGX‑0/603‑WGX‑1 (Sheet 2 of 4)
Seq
1
2
3
4
5
6
6
6
Item No
911-803-1
911-803-2
911-803-3
911-803-4
911-803-5
911-803-6
911-803-7
911-803-8
Description
Handle Cap Sound Control Foam
Exhaust Baffle Sound Control Foam
Enclosure Top Sound Control Foam
Base Ring Sound Control Foam
Motor Plate Sound Control Foam
Enclosure Foam 1 Sound Control
Enclosure Foam 2 Sound Control
Enclosure Foam 3 Sound Control
1
2
3
6
5
4
WGX-0_009
Repair or Warranty Contact
WGX-0
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
Page 11
Illustrated
Parts Breakdown
Illustrated
Parts
Breakdown
603‑WGX‑0/603‑WGX‑1 (Sheet 3 of 4)
Seq
1A
1B
2
3
4
5
6
7
8
9
10
11
12
13
14
Item No
600-A108-120
600-A108-220
600-WF-1364F
601-021
601-121
605-310B16
911-011
911-Q6600-220T
FE103208-HZSM-B
NE10320615-HNSZ
NE16201420-HNSZ
SE162005-PPSM-Z
SE162064-HHSM-Z
900-WH003
NE10320608-HNSZ
Description
Motor Assembly 120V
Motor Assembly 220V
Washer Fiber 13/64 ID x 3/8OD
Filter Adapter, WartHog
Mesh Disc, 3 in Diameter
HH Vac Head Base 16in SS Black
Gasket, Filter Adapter
Conical Motor Gasket Silica Gel
Hex Standoff, 10-32 MF x 1/2 SS With Bore
Nut, 10-32 Nylon Lock, SS, High
Nut 1/4-20 Hex Lock SS
Screw, 1/4-20 x 5/16 PH, SS
Screw 1/4-20 x 4in SS Hex
Wiring Harness, WGX General
Nut 10-32 Nylon Lock SS Short
10
1B
1A
WGX-0_005
For 120 V
For 220 V
7
4
14
11
5
WGX-0_006
13
9
12
6
Wiring Harness is Representative
Actual Harness May Differ in Appearance
3
8
Repair or Warranty Contact
WGX-0
Page 12
2
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
Illustrated Parts Breakdown
603‑WGX‑0/603‑WGX‑1 (Sheet 4 of 4)
Seq
1A
1B
2
3
4
5
6
Item No
600-Q6600-220T
600-Q6600-223T
605-310C
911-04G08
911-803-5
SE101212-PPSS-Z
WE133203-RFS-Z
Description
Motor Bypass 120V 13.5A 2HP 120CFM
Motor Bypass 220-240V 7.5A 2.3HP 120CFM
HH Vac Head Motor Collar SS
Grommet 7/32 ID, 1/2 OD
Motor Plate Sound Control Foam
Screw, Sheet Metal, #10 X .750, Phillips, SS
Washer .203ID X .500OD .047H Round Stainless Steel
4
5
6
2
3
1B
1A
For 220 V
For 120 V
WGX-0_007
Repair or Warranty Contact
WGX-0
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
Page 13
LIMITED LIFETIME WARRANTY TERMS AND CONDITIONS
Warranty Terms
Clayton Associates, Inc. guarantees its manufactured products against defects in materials or workmanship and will either repair or replace
all parts that prove defective under normal use during the lifetime of the products. The warranty period shall commence from the date of paid
invoice.
This warranty does not cover (a) repairs due to normal wear, accident, neglect, misuse, or use other than as indicated in the instruction booklet
(b) products manufactured by third parties and distributed by Clayton (c) wear items such as bearings, rotor blades, regulators, valve stems,
levers, shrouds, guards, O-rings, seals, gaskets, motor brushes, and other wearable parts.
Repair within the Continental US
During the first 90 days of the warranty period, Clayton will provide parts and labor to the customer’s site at no charge or pay freight costs
associated with returning the products for repair to a Clayton selected service location and repair the product at no charge. Clayton personnel
will determine the best way to repair the product.
Past 90 days, Clayton will provide parts to the customer’s site at no charge or the customer may ship the product to a Clayton selected service
location at customer’s expense and Clayton will repair the product at no charge and provide return shipping.
Repair Outside the Continental US
Clayton will provide parts to the customer’s site at no charge or the customer may ship the product to a Clayton selected service location at
customer’s expense and Clayton will repair the product at no charge and provide return shipping.
Limitation of Liability
Clayton shall not in any event be liable for any damages, loss of production time or profits, whether based on contract, warranty, negligence,
strict liability or otherwise, including without limitation any consequential, incidental or special damages, arising with respect to the equipment
or its failure to operate.
Clayton Associates, Inc. makes no other warranty or representation of any kind, except that of title, and all other warranties, express or implied,
including warranties of merchantability or fitness for any particular purpose, are hereby expressly disclaimed.
Repair or Warranty Contact
WGX-0
Page 14
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
EC Declaration of Conformity
Clayton Associates, Inc. of 1650 Oak Street, Lakewood New Jersey 08701 U.S.A. declare on our own responsibility that the
following equipment:
Industrial HEPA Filtered, Electrically Powered Vacuum Cleaners and Accessories for Dry Recovery
• Vacuum Models (where XXXX is the Tank Model):
WGX-XXXX-0, WGP-XXXX-0, WTX-XXXX-0, WTP-XXXX-0
WGX-XXXX-1, WGP-XXXX-1, WTX-XXXX-1, WTP-XXXX-1
• Tank Models: 107G, 107T, 115G, 115T, 205G, 205T, 215G, 215T
• With serial numbers ranging from WH0000001 through WH9999999
Are designed and manufactured in compliance with the essential requirements and other relevant provisions of the following
applicable directives:
• Machinery Directive 2006/42/EC
• The Electromagnetic Compatibility Directive 2004/108/EC
Compliance has been obtained by application of the following standards:
• EN ISO 12100:2010-11
• EN 60335-1:2012/A13 excluding 25.6
• EN 60335-2-69:2012 specifically Annex AA: Requirements for vacuum cleaners and dust extractors for the
collection of hazardous dusts
• EN 55014-1:2017
• EN 55014-2:2015
The legally authorized entity, established in the EU for compiling the technical file is ExVeritas Limited, Unit 16-18, Abenbury
Way, Wrexham Industrial Estate, Wrexham, LL13 9UZ, United Kingdom.
File Number: 18FILE0423
Subject to use for the purpose for which it was designed in accordance with relevant standards and with the manufacturer’s
recommendations. We hereby declare that the equipment specified above conforms to the listed Directives and Standards.
Brad Clayton
President
Clayton Associates, Inc.
Place of Issue: Lakewood, New Jersey, USA November 23, 2018
Repair or Warranty Contact
WGX-0
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
Page 15
EC Declaration of Conformity
Clayton Associates, Inc. of 1650 Oak Street, Lakewood New Jersey 08701 U.S.A. declare on our own responsibility that the
following equipment:
Industrial HEPA Filtered, Electrically Powered Vacuum Cleaners
• Vacuum Models (where XXXX is the Tank Model):
WGX-XXXX-0, WGP-XXXX-0, WTX-XXXX-0, WTP-XXXX-0
WGX-XXXX-1, WGP-XXXX-1, WTX-XXXX-1, WTP-XXXX-1
• Tank Models: 107G, 107T, 115G, 115T, 205G, 205T, 215G, 215T
• With serial numbers ranging from WH0000001 through WH9999999
Were tested to verify the integrity of the HEPA filter and the assembled machine.
Test Procedure:
• The test was performed using an aerosol generator and a photometer.
• The system was challenged with 18 microliters/mᶟ Poly Alfa Olefin (PAO).
• The system was fitted with a HEPA filter, part number 627-12H having a certified minimum efficiency of 99.995%.
Test Results:
• The filtration efficiency of the assembled WartHog vacuum was 99.9978%
• Test performed at: 740 Driving Park Avenue, Rochester NY 14613 USA
Declaration:
• The assembled unit meets the standard for US HEPA filtration and EU H14.
Brad Clayton
President
Clayton Associates, Inc.
Place of Issue: Lakewood, New Jersey, USA November 23, 2018
Repair or Warranty Contact
WGX-0
Page 16
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]
THIS PAGE IS INTENTIONALLY BLANK
Clayton products are proudly made in the USA
Repair or Warranty Contact
Clayton Associates, Inc. • 1650 Oak Street • Lakewood, New Jersey 08701 • P.+1-732-363-2100 F.+1-732-364-6084
www.DustlessMadeSimple.com • [email protected]