5. Operating the Network Camera

5. Operating the Network Camera
Network Camera User’s Guide
To prevent fire or shock hazard, do not expose the unit to rain or
moisture.
For AC Adaptor to avoid electrical shock, do not open the cabinet. Refer
servicing to qualified personnel only.
Notice: The changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment.
For customers in the U.S.A.
This equipment has been tested and found to comply with the limits for a digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:




Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this manual
could void your authority to operate this equipment.
The shielded interface cable recommended in this manual must be used with this
equipment in order to comply with the limits for a digital device pursuant to Subpart B of
Part 15 of FCC Rules.
2/65
Network Camera User’s Guide
Declaration of Conformity
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1)
(2)
this device may not cause harmful interference, and
this device must accept any interference received, including interference that may
cause undesired operation.
IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no
change to the antenna or the device is permitted. Any change to the antenna or the device
could result in the device exceeding the RF exposure requirements and void user’s authority
to operate the device.
NOTICE TO USERS
© 2006~12 All rights reserved. This manual or the software described herein, in whole or in
part, may not be reproduced, translated or reduced to any machine readable form without
prior written approval.
WE PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL, THE SOFTWARE OR
OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY
PARTICULAR PURPOSE WITH REGARD TO THIS MANUAL, THE SOFTWARE OR SUCH
OTHER INFORMATION. IN NO EVENT SHALL WE BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL OR SPECIAL DAMAGES, WHETHER BASED ON TORT, CONTRACT,
OR OTHERWISE, ARISING OUT OF OR IN CONNECTION WITH THIS MANUAL, THE
SOFTWARE OR OTHER INFORMATION CONTAINED HEREIN OR THE USE THEREOF.
We reserve the right to make any modification to this manual or the information contained
herein at any time without notice. The software described herein may also be governed by the
terms of a separate user license agreement.
3/65
Network Camera User’s Guide
Table of Contents
Overview ........................................................................................................................ 6
Introduction ............................................................................................................ 6
Features .................................................................................................................. 6
Minimum System Requirements............................................................................ 6
1. Package Contents ................................................................................................... 7
2. Physical Description .............................................................................................. 8
2.1 Front View ....................................................................................................... 8
2.2 Bottom View .................................................................................................... 8
3. Hardware Installation ........................................................................................... 10
4. Preparation ........................................................................................................... 12
4.1 Search and Set up by IPWizard II .................................................................. 12
4.1.1 Search ................................................................................................. 12
4.1.2 View .................................................................................................... 13
4.1.3 LAN .................................................................................................... 13
4.2 UPnP of Windows® XP, Vista or 7................................................................ 15
4.3 Install the Device behind a NAT Router ........................................................ 15
4.4 Access the device from the Internet Explorer for the first time .................... 16
4.5 Logging in as an User .................................................................................... 17
4.6 Logging in as an Administrator ..................................................................... 17
5. Operating the Network Camera ........................................................................... 17
5.1 Monitor Image Section .................................................................................. 18
5.2 Video Profile .................................................................................................. 18
5.3 Streaming Protocol ........................................................................................ 18
5.4 Language........................................................................................................ 18
5.5 2-Way Audio .................................................................................................. 19
5.6 Full Screen ..................................................................................................... 19
5.7 ActiveX Control............................................................................................. 19
5.7.1 Digital Zoom ....................................................................................... 20
5.7.2 Snapshot .............................................................................................. 20
5.7.3 Record ................................................................................................. 21
5.7.4 Volume ................................................................................................ 21
5.7.5 About ................................................................................................... 22
6. Administrating the Device ................................................................................... 23
6.1 System Setting ............................................................................................... 23
6.1.1 Network: Configure Network settings ................................................ 23
6.1.1.1 Network.................................................................................... 24
6.1.1.2 IPv6 .......................................................................................... 25
6.1.1.3 HTTPS ..................................................................................... 25
6.1.1.4 DDNS service .......................................................................... 26
6.1.1.5 PPPoE ...................................................................................... 27
6.1.1.6 Streaming ................................................................................. 28
6.1.7 UPnP ........................................................................................... 29
6.1.1.8 Bonjour .................................................................................... 30
6.1.1.9 ONVIF ..................................................................................... 30
6.1.1.10 IP Filter .................................................................................. 31
6.1.1.11 IP Notification ........................................................................ 32
6.1.2 Camera: Adjust Camera parameters.................................................... 34
6.1.2.1 Picture ...................................................................................... 34
4/65
Network Camera User’s Guide
6.1.2.2 Privacy Mask ........................................................................... 36
6.1.3 System: Configure and maintain system............................................. 37
6.1.3.1 System: ..................................................................................... 37
6.1.3.2 Date & Time ............................................................................. 38
6.1.3.3 Maintenance ............................................................................. 39
6.1.4 Video: Configure profile ..................................................................... 42
6.1.4.1 Common................................................................................... 42
6.1.4.2 Video Profile ............................................................................ 43
6.1.4.3 ROI........................................................................................... 44
6.1.5 Audio: Audio parameters .................................................................... 45
6.1.6 User: Manage user name, password and login privilege .................... 46
6.1.7 E-Mail: Setup E-Mail configuration ................................................... 47
6.1.8 Motion detection: Setup motion detection .......................................... 48
6.1.9 Audio detection: Setup audio detection .............................................. 49
6.1.10 Storage: Status and configuration of SD card ................................... 49
6.1.10.1 SD Card .................................................................................. 49
6.1.10.2 SAMBA Server ...................................................................... 51
6.1.11 Continuous Recording: ..................................................................... 52
6.1.12 Recording List: Files list inside the SD Card.................................... 53
6.1.12.1 Recording List ........................................................................ 53
6.1.12.2 Continuous Recording List .................................................... 53
6.1.13 Event Server: Setup FTP/TCP/HTTP/SAMBA server configuration
...................................................................................................................... 54
6.1.13.1 FTP Server ............................................................................. 54
6.1.13.2 TCP Server ............................................................................. 54
6.1.13.3 HTTP Server .......................................................................... 56
6.1.13.4 SAMBA Server ...................................................................... 56
6.1.14 Event Schedule: Configure the event schedule ................................. 58
6.1.14.1 Setting .................................................................................... 58
6.1.14.2 Record .................................................................................... 61
7. Using VLC Player to Access RTSP Streaming ........................................................ 62
8. Specification ............................................................................................................ 64
5/65
Network Camera User’s Guide
Overview
The user’s guide explains how to operate this camera from a computer. User should read this
manual completely and carefully before you operate the device.
Introduction
The device is accessible via the LAN or Internet connection. Connect your device directly to a
local area network or xDSL modem, and with Microsoft® Internet Explorer you get instant, on
demand video streams. Within minutes you can set up the device to capture a video
sequence to a PC.
Features




















ONVIF compliant
Easy installation with setup wizard (IP Wizard II)
UPnP device discovery and NAT router transversal for easy installation
Dynamic IP Service, DIPS® , to search your IP camera from Internet easily
H.264 and MJPEG multi-profile compression simultaneously
1.3 Mega-pixel resolution
1.3 Mega-pixel or 720P mode selectable
8-profile encoder simultaneously
UDP / TCP / HTTP / HTTPS protocols selectable
Digital zoom
Built-in microphone
Audio line out
Two-way audio
Micro SD slot
Intelligent motion detection up to 10 zones
Voice alerting while event triggered
Privacy masks
3D de-noise to improve picture quality at low lux.
Image transmission using an FTP or e-mail for event
DDNS and PPPoE
Minimum System Requirements






Microsoft Internet Explorer 6.0 or later
Microsoft Media Player 11.0 or later (to playback recorded file)
VGA Monitor resolution 1280 x 1024 or higher
Pentium-4 3.6 GHz or higher
Memory Size: 1GB or more
Windows XP, Vista, 7
6/65
Network Camera User’s Guide
1. Package Contents
■
■
■
■
■
Cube Network Camera
CD-ROM (User manual and IP utility)
Quick Start Guide
Camera mounting kit
Power adapter (DC12V)
If any of the above items are missing, please contact your dealer immediately.
Note: Using a power supply with a different voltage than the one included with the Network
Camera will cause damage and void the warranty for this product.
7/65
Network Camera User’s Guide
2. Physical Description
2.1 Front View
Microphone
Lens & focus ring
Micro-SD
Lens & focus ring
User could use this ring to adjust focus manually.
Microphone
The Camera has built-in an internal microphone. This microphone is hidden in the pinhole located
on the front panel.
Micro SD Card Slot
User can insert a micro SD card into this slot for event recording.
2.2 Bottom View
Audio Output Jack
Audio-out Jack allows this device to output audio or alerting sound.
DC Power Jack
The input power is 12VDC. Note that supply the power to the Camera with the power adapter
included in package. Otherwise, the improper power adapter may damage the unit and result in
danger.
Power LED
LAN LED
DC Power Jack
Audio Output Jack
LAN Socket
Factory Default Reset
Factory Default Reset
This button is hidden in the pinhole. This button is used to restore the all factory default settings.
Sometimes restarting the camera will make the system back to a normal state. If the system still
8/65
Network Camera User’s Guide
got problems after restart, user can restore the factory default settings and install it again. To
restore the device, please follow the steps below:
1. Make sure the Camera is ready first. Insert the paper clip or other tool and press and hold the
button down continuously.
2. Hold it at least 5 seconds and release the tool while the Camera is operating. Then the device
has been restored to default settings and reboot again.
Note: Restoring the factory default setting will lose the all previous settings included IP address
forever. User needs to run the IPWizard II program to search the device and configure it to let the
device work properly again.
LAN Socket
The LAN socket is a RJ-45 connector for connections to 10Base-T Ethernet or 100Base-TX Fast
Ethernet cabling. This Ethernet port built N-Way protocol can detect or negotiate the transmission
speed of the network automatically. Please use Category 5 cable to connect the Network Camera
to a 100Mbps Fast Ethernet network switch or hub.
LAN LED (green color)
This LED will be flashing while network accessing via Ethernet.
Power
This LED is used to indicate whether the camera is ready or not.
9/65
Network Camera User’s Guide
3. Hardware Installation
1. Attach the Camera with the included stand
2. Place the Camera on the table or fix it onto ceiling or wall
Use three screws to fix the Network Camera onto the ceiling or wall. You could also put the
Network Camera on the table directly.
Fixed it by
Screws
3. Plug an Ethernet cable into the Camera
Connect an Ethernet cable to the LAN socket located on the Network Camera’s bottom and
attach it to the network.
Ethernet Cable
10/65
Network Camera User’s Guide
4. Connect the external power supply to Camera
Connect the attached power adapter to the DC power jack of the Network Camera. Note: Use the
power adapter, 12VDC, included in the package and connect it to wall outlet for AC power.
Power Cable
Once you have installed the camera well and powered it on, the Power LED (orange) will turn on
later. Once the Power LED turned on, it means the system is booting up successfully.
Furthermore, if you have a proper network connection, and access to the camera, the LAN LED
(green) will flash green under wired mode.
11/65
Network Camera User’s Guide
4. Preparation
4.1 Search and Set up by IPWizard II
When you installed the Camera on a LAN environment, you have two easy ways to search your
Cameras by IPWizard II or UPnP™ discovery. Here is the way to execute IPWizard II to discover
Camera’s IP address and set up related parameter in a Camera.
4.1.1 Search
When launch the IP Wizard II, a searching window will pop up. IP Wizard II is starting to search
Network Cameras on the LAN. The existed devices will be listed as below.
12/65
Network Camera User’s Guide
4.1.2 View
If IP Wizard II finds network devices, View button will be available. Please select the device you
want to view and click the View button. Then you could see the video from camera directly.
Furthermore you could double click the left button of mouse to link to the network device by
browser.
4.1.3 LAN
In case you want to change the IP related parameters of wired interface, please select the device
you want to configure and click the LAN button. Relative settings will be carried out as below.
You could modify the relative settings of the selected device. Click “<<” button will quit the LAN
13/65
Network Camera User’s Guide
setting procedure and click “>>” button will move to next page as below.
In case, you do not want to change username and/or password, then just click “Submit” button to
perform your setting accordingly. Click “<<” button will go back to previous page.
If you like to change username and/or password of the device, just click the check button. Then,
the related fields will show up as below.
After keying in new username and password, click “Submit” button to perform your setting
accordingly. Click “<<” button will go back to previous page.
14/65
Network Camera User’s Guide
4.2 UPnP of Windows® XP, Vista or 7
UPnP™ is short for Universal Plug and Play, which is a networking architecture that provides
compatibility among networking equipment, software, and peripherals. This device is an UPnP
enabled device. If the operating system, Windows XP, Vista or 7, of your PC is UPnP enabled,
the Network Camera will be very easy to be found.
Please make sure to enable UPnP settings first if your operating system of PC is running
Windows XP.
Note: Windows 2000 does not support UPnP feature.
To discover your device, go to your Desktop and click My Network Places.
Click the targeted Device. Then Internet Explorer will connect to this Network Camera
automatically.
4.3 Install the Device behind a NAT Router
Once installed, the device is accessible on your LAN. To access the device from the Internet you
must configure your broadband router to allow incoming data traffic to the device. If the device is
installed on the LAN with a router, then it may get a dynamic IP address from the DHCP server.
However, if the device wants to be accessed from the WAN, its IP address needs to be setup as
fixed IP, also the port forwarding or Virtual Server function of router needs to be setup.
However, if your NAT router supports UPnP feature, it can be very easy to achieve NAT traversal
automatically. To do this, enable the NAT-traversal feature, which will attempt to automatically
configure the router to allow access to the camera.
Installing the device with an UPnP router on your network is an easy 3–step procedure:
(1) Enable UPnP option of your NAT router
(2) Enable UPnP NAT traversal option of the Network Camera (default)
(3) Access your Network Camera by DIPS
(1) Enable UPnP option of your NAT router
15/65
Network Camera User’s Guide
To use UPnP IGD function (NAT traversal), you need to make sure the UPnP function is enabled
in your router. Most new home routers should support this function. Some of routers are default
enable and others are not. Please check user’s manual of your NAT router for detail.
(2) Enable UPnP NAT traversal option of the Network Camera
Refer to Setting  Network  UPnP page for detail NAT traversal setting. Note that this option
is default enabled.
(3) Access your Network Camera by DIPS
Refer to Setting  System  System page for detail DIPS information.
4.4 Access the device from the Internet Explorer for the first
time
1.
Start the web browser on the computer and type the IP address of the Camera you want
to monitor as below:
The Login Window of the Camera is prompted:
2.
Type in your login name and password under “USERNAME” and “PASSWORD” textbox.
For the first time use (default value), input the
User Name: admin
Password: 1234
That’s, type in “admin” on the “USERNAME” as a default name and leave PASSWORD
textbox blank. Click “OK” button to start the main menu.
3.
According your browser’s security setting, the IE Web Page may prompt the “Security
Warning” window. If so, select “Yes” to install and run the ActiveX control into your PC.
Otherwise, the system will load the ActiveX silently.
4.
After the ActiveX control was installed and ran, the first image will be displayed.
16/65
Network Camera User’s Guide
4.5 Logging in as an User
If you log in the Camera as an ordinary User, “Setting” function will be not accessible.
4.6 Logging in as an Administrator
If you log in the Camera as the Administrator, you can perform all the settings provided by the
device.
5. Operating the Network Camera
Start-up screen will be as follow no matter an ordinary users or an administrator.
ActiveX
Control
Monitor Image
Section
2-Way 17/65
Audio
Full
Screen
Network Camera User’s Guide
5.1 Monitor Image Section
The image shot by the device is shown here. The date and time are displayed at the top of
the window.
5.2 Video Profile
The device supports multi-profile function for H.264 and MJPEG simultaneously. User can
chose the proper and/or preferred profile which is listed here.
5.3 Streaming Protocol
User can select proper streaming protocol according to networking environment.
5.4 Language
The device could provide multiple languages to meet customer’s requirement.
18/65
Network Camera User’s Guide
5.5 2-Way Audio
The device supports 2-way audio function. User can chose to enable or disable this function
by toggling the icon below.
Disable audio uploading function.
Enable audio uploading function.
5.6 Full Screen
Enlarge video to full screen display.
Enlarge video to full screen display. Press “ESC” key to disable this function.
5.7 ActiveX Control
The plug-in ActiveX control supports a lot of functions by clicking the left mouse button. Note
that this feature only supports on the ActiveX control within Microsoft® Internet Explorer.
On the ActiveX control icon, click the Left Mouse Button, then a menu pop-up. This menu
provides features that are unique to the ActiveX control. These features include:
“Digital Zoom”, “Snapshot”, “Record”, “Volume”, “About”
19/65
Network Camera User’s Guide
5.7.1 Digital Zoom
Click Digital Zoom to active this function as above. User can drag or scale the box over
the video to adjust zoom ratio and position.
5.7.2 Snapshot
Click Snapshot to activate this function. Press Snapshot button to take a picture. The
image file is saved as JPEG format into your local PC. Select Browser, the pop-up
window to select the save path and file name prefix, select OK to continue.
If you like to retrieve the saved image, select the file to display the saved image by using any
one of graph editing tools.
20/65
Network Camera User’s Guide
5.7.3 Record
Click Record to activate this function. Press Record button to start recording. The video file is
saved as ASF format into your local PC. While you want to stop it, press Stop to stop
recording. Select Browser, the pop-up window to select the save path and file name prefix,
select OK to continue.
After stop recording, list the files, this file is named as Video_yyyymmddhhmmss.avi
The ASF files can be display by the standard Windows Media Player, but it needs the DixectX
9.0 or later version to be installed.
5.7.4 Volume
Click Volume to activate this function. There are two control bars for speaker and microphone
volume respectively. Scroll these control bars to adjust the audio attribute. Check the volume
mute will mute the speaker output.
21/65
Network Camera User’s Guide
5.7.5 About
Click About to show this ActiveX information.
22/65
Network Camera User’s Guide
6. Administrating the Device
6.1 System Setting
This function is only available for user logged into Camera as administrator.
Click on each menu name to display its setting page.
Item
Action
Network
Configure Network settings such as DHCP, DDNS, 3GPP,
PPPoE and UPnP
Camera
Adjust camera parameters, position, and set camera tour
System
Configure system information, date & time, maintenance, and
view system log file.
Video
Configure bit rate and frame rate of video profiles
Audio
Configure audio parameters
User
Setup user name, password and login privilege
E-Mail
Setup E-Mail configuration
Event Detection
Setup Event detection
Storage
Status and configuration of SD card
Continuous Recording
Configure storage type and path
Recording List
Files list inside the SD Card
Event Server
Setup FTP/TCP/HTTP server for event
Event Schedule
Configure the schedule while event triggered
6.1.1 Network: Configure Network settings
Use this menu to configure the network to connect the device and the clients.
23/65
Network Camera User’s Guide
6.1.1.1 Network
This section provides the menu for connecting the device through Ethernet cable.
MAC address:
Displays the Ethernet MAC address of the device. Note that user can not modify it.
Obtain IP address automatically (DHCP):
DHCP: Stands for Dynamic Host Configuration Protocol.
Enable this checked box when a DHCP server is installed on the network to issue IP address
assignment. With this setting, the IP address is assigned automatically. If this device can not
get an IP address within limited tries, the device will assign a default IP address,
192.168.0.100, by itself as the default IP address.
IP address, Subnet mask, and Gateway:
If you do not select Obtain an IP address automatically, then you need to enter these
network parameters manually.
Obtain DNS from DHCP:
DNS: Stands for Domain Name System.
Enable this checked box when a DHCP server is installed on the network and provide DNS
service.
Primary DNS and Secondary DNS:
If you do not select Obtain DNS from DHCP, then you need to enter these parameters
manually.
HTTP Port:
The device supports two HTTP ports. The first one is default port 80 and this port is fixed.
This port is very useful for Intranet usage. The second HTTP port is changeable. Users could
assign the second port number of http protocol, and the WAN users should follow the port
number to login. If the http port is not assigned as 80, users have to add the port number in
back of IP address. For example: http://192.168.0.100:8080.
Therefore, the user can access the device by either
24/65
Network Camera User’s Guide
http://xx.xx.xx.xx/, or
http://xx.xx.xx.xx:xxxx/ to access the device.
If multiple devices are installed on the LAN and also required to be accessed from the WAN,
then the HTTP Port can be assigned as the virtual server port mapping to support multiple
devices.
Click “OK” to save and enable the setting.
6.1.1.2 IPv6
The IP communication protocol used for current Internet is having the problem of insufficient
IP addresses. The one-for-all solution is the new-generation internet protocol, IPv6. IPv6 has
16-byte long address space, offering a huge number of addresses, and also provides better
scalability, quality of service, mobility, and security to the network.
IPv6:
To enable or disable the IPv6 service here.
6.1.1.3 HTTPS
HTTPS: Stands for Hypertext Transfer Protocol Secure
HTTPS is a combination of the Hypertext Transfer Protocol with the SSL/TLS protocol to
provide encrypted communication and secure identification of a network web server. HTTPS
connections are often used for sensitive transactions in corporate information systems. The
main idea of HTTPS is to create a secure channel over an insecure network. This ensures
reasonable protection from eavesdroppers and man-in-the-middle attacks, provided that
adequate cipher suites are used and that the server certificate is verified and trusted.
HTTPS:
To enable or disable the HTTPS service here. Note that the HTTPS function of this device is
not only encrypted the web content but also audio/video data.
If the HTTPS is enabled, there is further option for “HTTP&HTTPS” or “HTTPS only”. In case,
the “HTTPS only” is enabled, all packets from the Camera will go through HTTPS only and
HTTP service is no longer available.
Port:
25/65
Network Camera User’s Guide
Choose the HTTPS port. The default value is 443.
6.1.1.4 DDNS service
DDNS: Stands for Dynamic Domain Name Server
Your Internet Service Provider (ISP) provides you at least one IP address which you use to
connect to the Internet. The address you get may be static, meaning it never changes, or
dynamic, meaning it’s likely to change periodically. Just how often it changes, depends on
your ISP. A dynamic IP address complicates remote access since you may not know what
your current WAN IP address is when you want to access your device over the Internet. One
of the possible solutions to the dynamic IP address problem comes in the form of a dynamic
DNS service.
A dynamic DNS service is unique because it provides a means of updating your IP address
so that your listing will remain current when your IP address changes. There are several
excellent DDNS services available on the Internet. One such service you can use is
www.DynDNS.org. You’ll need to register with the service and set up the domain name of
your choice to begin using it.
If your device is connected to xDSL directly, you might need this feature. However, if your
device is behind a NAT router, you will not need to enable this feature because your NAT
router should take care of this job. As to xDSL environment, most of the users will use
dynamic IP addresses. If users want to set up a web or a FTP server, then the Dynamic
Domain Name Server is necessary.
26/65
Network Camera User’s Guide
DDNS:
To enable or disable the DDNS service here.
Server name:
Choose one of the built-in DDNS servers.
DDNSHost:
The domain name is applied of this device.
User name:
The user name is used to log into DDNS.
Password:
The password is used to log into DDNS.
6.1.1.5 PPPoE
PPPoE: Stands for Point to Point Protocol over Ethernet
A standard builds on Ethernet and Point-to-Point network protocol. It allows your device with
xDSL or cable connects with broadband network directly, then your device can dial up and get
a dynamic IP address. For more PPPoE and Internet configuration, please consult your
dealer or ISP.
The device can directly connect to the xDSL, however, it should be setup on a LAN
environment to program the PPPoE information first, and then connect to the xDSL modem.
Power on again, then the device will dial on to the ISP connect to the WAN through the xDSL
modem.
The procedures are

Connect to a LAN by DHCP or Fixed IP

Access the device, enter Setting  Network  PPPoE as below
27/65
Network Camera User’s Guide
PPPoE:
To enable or disable the PPPoE service here.
User name:
Type the user name for the PPPoE service which is provided by the ISP.
Password:
Type the password for the PPPoE service which is provided by the ISP.
IP address, Subnet mask, and Gateway (read only):
Shows the IP information got from PPPoE server site.
Status:
Shows the Status of PPPoE connection.
6.1.1.6 Streaming
RTSP is a streaming control protocol, and a starting point for negotiating transports such as
RTP, multicast and Unicast, and for negotiating codecs. RTSP can be considered a "remote
control" for controlling the media stream delivered by a media server. RTSP servers typically
use RTP as the protocol for the actual transport of audio/video data.
RTSP Port:
Choose the RTSP port. The RTSP protocol allows a connecting client to start a video stream.
Enter the RTSP port number to use. The default value is 554.
RTP Port:
Specify the range of transmission port number of video stream. The default range is 50000 to
50999. User can specify a number between 1024 and 65535.
28/65
Network Camera User’s Guide
6.1.7 UPnP
UPnP is short for Universal Plug and Play, which is a networking architecture that provides
compatibility among networking equipment, software, and peripherals. This device is an
UPnP enabled Network Camera. If your operating system is UPnP enabled, the device will
automatically be detected and a new icon will be added to “My Network Places.” If you do not
want to use the UPnP functionality, it can be disabled.
In addition, this device also provides UPnP IGD function for NAT traversal easily. Use NAT
traversal when your device is located on an intranet (LAN) and you wish to make it available
from the other (WAN) side of a NAT router. With NAT traversal properly configured, all HTTP
traffic to an external HTTP port in the NAT router will be forwarded to the device.
UPnP:
To enable or disable the UPnP service here.
29/65
Network Camera User’s Guide
Friendly Name:
To show the friendly name of this device here.
UPnP NAT Traversal
When enabled, the device will attempt to configure port mapping in a NAT router on your
network, using UPnP™. Note that UPnP™ must be enabled in the NAT router first.
Port Range:
The port range will open in NAT router.
External IP address:
Show the IP address and port for WAN access through Internet. If NAT traversal is configured
successfully, user can use this IP address and port to access this device. The external IP
address is not shown in case NAT traversal function is failed.
6.1.1.8 Bonjour
Bonjour, also known as zero-configuration networking, enables automatic discovery of
computers, devices, and services on IP networks. Bonjour uses industry standard IP
protocols to allow devices to automatically discover each other without the need to enter IP
addresses or configure DNS servers. Specifically, Bonjour enables automatic IP address
assignment without a DHCP server, name to address translation without a DNS server, and
service discovery without a directory server. Bonjour is an open protocol which Apple has
submitted to the IETF as part of the ongoing standards-creation process.
Bonjour:
To enable or disable the Bonjour service here.
Friendly Name:
To show the friendly name of this device here.
6.1.1.9 ONVIF
ONVIF is a global and open industry forum with the goal to facilitate the development and use
of a global open standard for the interface of physical IP-based security products. Or in other
words, to create a standard for how IP products within video surveillance and other physical
security areas can communicate with each other.
30/65
Network Camera User’s Guide
ONVIF:
To enable or disable the ONVIF interface here. And select the ONVIF version to match
client’s supported version.
6.1.1.10 IP Filter
You can enter different user’s IP address which are allowing enter or denying by the device.
IP Filter:
To enable or disable the IP filter function here.
IP Filter Policy:
Choose the filter policy where is denying or allowing.
31/65
Network Camera User’s Guide
6.1.1.11 IP Notification
In case the IP address is changed, system is able to send out an email to alert someone if the
function is enabled.
SMTP Notification (e-mail):
If enable this function, then the “Send to” and “Subject” fields need to be filled.
Send To:
Type the receiver’s e-mail address. This address is used for reply mail.
Subject:
Type the subject/title of the E-mail.
TCP Notification:
If enable this function, then the “TCP Server”, “TCP Port”, and “Message” fields need to be
filled.
TCP Server:
Type the server name or the IP address of the TCP server.
TCP Port:
Set port number of TCP server.
Message:
The message will be sent to FTP server.
HTTP Notification:
If enable this function, then the fields below need to be filled.
URL:
Type the server name or the IP address of the HTTP server.
HTTP Login name:
Type the user name for the HTTP server.
HTTP Login Password:
Type the password for the HTTP server.
32/65
Network Camera User’s Guide
Proxy Address:
Type the server name or the IP address of the HTTP Proxy.
Proxy Port:
Set port number of Proxy.
Proxy Login name:
Type the user name for the HTTP Proxy.
Proxy Login Password:
Type the password for the HTTP Proxy.
Custom parameter:
User can set specific parameters to HTTP server.
Message:
The message will be sent to HTTP server.
33/65
Network Camera User’s Guide
6.1.2 Camera: Adjust Camera parameters
Use this menu to set the functions of the camera parameters of the device.
6.1.2.1 Picture
Rotation:
Turn the “Mirror” and “Vertical Flip” On or OFF. The image will be overturned as below.
34/65
Network Camera User’s Guide
White Balance:
Auto: will adjust the white balance automatically.
Hold: will hold the white balance.
Exposure Control:
Auto: will adjust the internal gain automatically.
Hold: will hold the internal gain.
Color Level:
Large value will be colorful.
Brightness:
Large value will brighten camera.
Contrast:
Large value will contrast camera heavily.
Sharpness:
Large value will sharpen camera.
3D De-Noise:
De-Noise can remove or lower unwanted noise and preserve fine details and edges.
Image Control:
Use built-in photo sensor or manual to control image color.
In case user selects manual mode, there are 4 modes: B/W, Color, Auto or Schedule. This
function is very useful under low illumination environment.
In case the Auto mode is selected, user needs to specify 3 parameters in advance:
B/W Threshold (0~10000): this value set the threshold to switch to B/W mode. It should be
lower or equal to Color Threshold.
Color Threshold (0~10000): this value set the threshold to switch to Color mode. It should be
higher or equal to B/W Threshold.
Delay Time: The delay time between B/W and Color mode switching.
Note that Current Value is the current luminance from the captured video. It’s a useful
reference to set B/W and Color Threshold.
Default Settings:
Restore to factory image settings.
35/65
Network Camera User’s Guide
6.1.2.2 Privacy Mask
Use this page to specify privacy mask window 1 to window 8 and set the name and gray
level for selected window.
Add and Delete:
To add or delete the privacy mask windows, user can specify up to 7 windows to mask
the video captured by this device. By dragging mouse on the image, you can change the
position and size of the selected window accordingly.
Name:
Name of the specified privacy window.
Level
To define the gray level of mask block. The smaller value will be darker.
36/65
Network Camera User’s Guide
6.1.3 System: Configure and maintain system
Use this menu to perform the principal settings of the device.
6.1.3.1 System:
DIPS (Dynamic IP Service): -Function DiscardedTo enable or disable the DIPS® (Dynamic IP Service) function.
Device ID (for DIPS): -Function DiscardedIt’s a unique number of each device for identification and this ID is used for DIPS.
It’s feasible to locate your device from Internet by DDNS service. However, we provide
another easier way to do the same job called Dynamic IP Service, DIPS® .
To use this service, just follow four steps below:
(1) Enable DIPS function of the device
(2) Check your Device ID from this page. This is a unique number for each device.
(3) If your device is behind a NAT router, please configure your device properly. You could
refer to section “Install the Camera behind a NAT Router” above. You only need to do this job
one time.
(4) Visiting company’s website, you can find DIPS service page as below:
Enter your Device Number and press “OK” button.
Then, a new web page will pop up and link to your device accordingly.
37/65
Network Camera User’s Guide
You will see that DIPS is a much easier service than DDNS.
Device Title:
You can enter the name of this unit here. It’s very useful to identify the specific device from
multiple units. The information will be shown on IPWizard II once the device is found.
Software Version:
This information shows the software version of the device.
Network(LAN) LED:
To turn on or off Network(LAN) LED.
Power LED (Wireless LED):
To turn on or off the Power LED (wireless LED if WLAN model).
Log:
User can check the system log information of the device, including the Main Info, Appended
Info, Operator IP, and so on …
Reload:
Click this button; user can refresh the log information of the device.
6.1.3.2 Date & Time
You can setup the device or make it synchronized with PC or remote NTP server. Also, you
may select your time zone in order to synchronize time locally.
Server Date & Time:
Displays the date and time of the device.
PC Time:
Displays the date and time of the connected PC.
Adjust:

Synchronize with PC:
Click this option to enable time synchronization with PC time.

Manual setting:
Click this option to set time and date manually.

Synchronize with NTP:
Click this option if you want to synchronize the device’s date and time with those of time
server called NTP server (Network Time Protocol).
NTP Server: Type the host name or IP address or domain name of the NTP server.
NTP sync. Interval: Select an interval between 1 and 24 hours at which you want to
adjust the device’s time referring to NTP server
Time zone:
Set the time difference from Greenwich Mean Time in the area where the device is installed.
Daylight Saving:
Disable or enable the daylight saving adjustment.
38/65
Network Camera User’s Guide
6.1.3.3 Maintenance
Hard Factory Default (Include the network setting):
Recall the device hard factory default settings. Note that click this button will reset all device’s
parameters to the factory settings (including the IP address).
Factory Default (Except the network setting):
The unit is restarted and most current settings are reset to factory default values. This action
will not reset the network setting.
Backup Setting:
To take a backup of all of the parameters, click this button. If necessary, it will then be
possible to return to the previous settings, if settings are changed and there is unexpected
behavior.
Restore Setting:
Click the “Browse” button to locate the saved backup file and then click the “Restore
Setting” button. The settings will be restored to the previous configuration.
39/65
Network Camera User’s Guide
Firmware Upgrade:
The device supports new firmware upgrade (the software that controls the operation in the
device). Please contact your dealer for the latest version if necessary.
Download the latest firmware file from our website or your dealer. Unzip this firmware file to
binary file and store it into your PC. Then follow the steps as bellow carefully:
1.
Close all other application programs which are not necessary for firmware update.
2.
Make sure that only you access this device while firmware updating.
3.
Disable all event trigger and/or schedule trigger functions first.
4.
In this web page, click “Browse” button. Select the Firmware binary file.
5.
Once the firmware file was selected, click “Firmware Upgrade” button.
6.
The upgrade progress information will be displayed. Once the uploading process
completed, the device will reboot the system automatically.
7.
Please wait for timer countdown, and then you can use IPWizard II to search the device
again.
40/65
Network Camera User’s Guide
Warning!!! The download firmware procedure cannot be interrupted. If the power
and/or network connection are broken during the download procedure, it WILL cause
serious damage to the device.
Strongly suggest that DO NOT upgrade firmware via Wireless LAN due to high error
rate possibly and don't allow any other clients to access this unit during updating
procedure.
Be aware that you SHALL NOT turn off the power during updating the firmware and
shall wait for finish message.
Furthermore, the firmware upgrade procedure is always risky and do not try to upgrade
new firmware if it’s not necessary.
System Restart:
The device is restarted without changing any of the network settings. It means the IP address
of the device will not change after firmware upgrade.
41/65
Network Camera User’s Guide
6.1.4 Video: Configure profile
This device provides 2 modes of video profile. The first one is 1.3 Mega mode which supports
video resolution up to 1.3 Mega-pixel. Maximum frame rate of this mode is up to 30fps. The
second one is 720p mode which supports video resolution up to 1280x720 but frame rate can
be up to 30fps. User only can select either 1.3 Mega or 720p mode to operate the camera.
Switching 1.3 Mega and 720p mode, the device will take time to re-configure system.
6.1.4.1 Common
Video Profile:
User can only choose either 720p or 1.3 Mega modes. 720p mode can serve streams up to
1280x720 resolution maximum. On the other hand, 1.3 Mega mode, it can streams up to 1280
x 1024 resolution (depend on model) maximum.
Text Overlay Setting:
There are some important information can be embedded into image, including date, time,
and/or text. User also can change the font color, background color, or Transparency.
42/65
Network Camera User’s Guide
6.1.4.2 Video Profile
Name:
To assign a name to the selected profile.
Video Type:
Video codec of the selected profile.
Resolution:
Show the resolution of the selected profile.
ROI:
Assign the selected profile as a ROI stream or not. (Only available for the profiles with max
resolution)
Rate Control:
Defines the rate control method of this profile. There are four options: Constant Bit Rate
(CBR), Variable Bit Rate (VBR), Enhanced Constant Bit Rate (ECBR), and Enhanced
Variable Bit Rate (EVBR).
For CBR, the video bit rate is between low to high bandwidth based on different resolutions.
User can set the desired bit rate to match the limitation of bandwidth.
For VBR, user should choose the quality level to set the video quality rather than bit rate. The
quality level is between 1 and 100. The higher value can reach the better quality but of course
will consume higher bandwidth.
For ECBR, the video bitrate is based on normal CBR mode. However, the target bitrate can
be increased to max target bitrate while lots of motion in video. The max target bitrate will
keep a pre-defined time period and then back to normal CBR bitrate.
For EVBR, the video bitrate is based on normal VBR mode. However, the bitrate can be
limited to the max bitrate while lots of motion in video.
Max Frame Rate:
Defines the targeted frame rate of this profile. For example, set the frame rate to 15 fps, then
the image will be updated for 15 frames per second as possible. User need to set reasonable
max frame rate versus video quality under the limited bandwidth.
43/65
Network Camera User’s Guide
GOP Control:
Defines the Intra/Inter-frame (I/P) ratio of this profile. For example, set the GOP to 30, then
the video stream will have one Intra-frame every 30 frames.
Multicast:
Enable or disable the multicast function.
Multicast Video:
IP address and port for multicast video streaming of the selected profile.
Multicast Audio:
IP address and port for multicast audio streaming of the selected profile.
Time to live:
Time to live (TTL) is a mechanism that limits the lifespan of data in a computer or network.
Once the prescribed event count or time span has elapsed, data is discarded. TTL prevents a
data packet from circulating indefinitely.
Always Enable Multicast:
Multicast streaming is always enabled or by request.
Warning!!! To enable the multicast streaming, you shall make sure your Intranet does
support multicast function. Otherwise, your Intranet may occur network storm
seriously.
6.1.4.3 ROI
ROI means Region of Interest. This feature is available in 1.3M resolution only. Use this page
to specify location of ROI windows.
44/65
Network Camera User’s Guide
6.1.5 Audio: Audio parameters
Audio:
To enable or disable audio function
Audio Type:
To select audio codec
Mute While PT:
Mute the audio while pan and/or tilt motion
Audio Mode:
To select Simplex or Full duplex (2-way audio) mode
Input Gain:
To adjust gain of input audio
Output Gain:
To adjust gain of output audio
45/65
Network Camera User’s Guide
6.1.6 User: Manage user name, password and login privilege
Use this menu to add, update, or remove the usernames and passwords of the Administrator
and viewer.
Access Right:
Administrator can access every function in this device. However, Viewers only can view the
video and access limited function.
Add, update, and remove of Users account:
Manage the user’s account of viewer user.
46/65
Network Camera User’s Guide
6.1.7 E-Mail: Setup E-Mail configuration
User may setup SMTP mail parameters for further operation of Event Schedule. That’s, if
users want to send the alarm message out, it will need to configure parameters here first and
also add at least one event schedule to enable event triggering.
SMTP Server:
Type the SMTP server name or the IP address of the SMTP server.
Test:
Send a test mail to mail server to check this account is available or not.
SMTP Port:
Set port number of SMTP service.
SSL:
Enable SSL function or not.
SMTP Authentication:
Select the authentication required when you send an e-mail.

Disable: if no authentication is required when an e-mail is sent.

Enable: if authentication is required when an e-mail is sent.
Authentication User name:
Type the user name for the SMTP server if Authentication is Enable.
Authentication Password:
Type the password for the SMTP server if Authentication is Enable.
E-mail From:
Type the sender’s E-mail address. This address is used for reply e-mails.
E-mail To:
Type the receiver’s e-mail address.
E-mail Subject:
Type the subject/title of the e-mail.
47/65
Network Camera User’s Guide
6.1.8 Motion detection: Setup motion detection
Use this menu to specify motion detection window 1 to window 10 and set the conditions for
detection while observing a captured image.
Add and Del:
To add or delete the motion windows. User can specify up to 10 Included and/or Excluded
windows to monitor the video captured by this device. By dragging mouse on the image, you
can change the position and size of the selected motion window accordingly.
Included or Excluded Window:
These windows can be specified as Included or Excluded type.
Included windows target specific areas within the whole video image
Excluded windows define areas within an Include window that should be ignored
(areas outside Include windows are automatically ignored)
Name:
Name of the specified motion window.
Object Size:
Defines the object size of motion detection. The higher object size will only larger objects
trigger motion detection. The lower object size will even small objects trigger motion detection
too. Generally speaking, the smaller size will be easier to trigger event.
Sensitivity
Defines the sensitivity value of motion detection. The higher value will be more sensitivity.
48/65
Network Camera User’s Guide
6.1.9 Audio detection: Setup audio detection
Use this menu to specify audio alarm level. Event will be triggered if detected audio volume
exceeds the alarm level.
Audio Alarm Level:
Move the slide to specify the audio alarm level. The level bar will change accordingly in the
picture below and current detected volume is displayed in blue.
6.1.10 Storage: Status and configuration of SD card
6.1.10.1 SD Card
This page shows the status of attached SD card. You may setup related parameters to
manage the attached SD card also.
49/65
Network Camera User’s Guide
Enable automatic disk cleanup:
Delete old recorded files while the conditions are reached as below.
Remove recordings order than:
Delete old files by days.
Remove oldest recordings when disk is:
Delete old files by left capacity.
50/65
Network Camera User’s Guide
6.1.10.2 SAMBA Server
This page shows the status of SAMAB server. You may setup related parameters to manage
the remote SAMBA server.
Host:
Type the SAMBA server domain name or the IP address of the SMTP server.
Share:
Type the share folder of remote SAMBA server which the camera will upload files to this
space.
User name:
Type the user name for the remote SAMBA server.
Password:
Type the password for the remote SAMBA server.
51/65
Network Camera User’s Guide
6.1.11 Continuous Recording:
The camera can continuously record video stream into files and save them to attached SD
card or remote SAMBA server.
Note that there are various factors affecting the recording results, such as the camera’s
system loading, network condition, SD card performance, multiple client accessing, and so on.
No guarantee will be given to “seamless recording” in the recorded video files.
Continuous Recording:
Enable or disable this function.
Record File Type:
Choose a video profile to record.
DISK:
Save recorded files to SD card or remote SAMBA server.
Path:
Define the folder path for the recorded files.
Restart:
Be careful, click this button will delete all continuous files recorded in SD card or remote
SAMBA server.
52/65
Network Camera User’s Guide
6.1.12 Recording List: Files list inside the SD Card
6.1.12.1 Recording List
This page only shows the event recording files which stored in SD card. User may play or
delete the selected file.
6.1.12.2 Continuous Recording List
This page only shows the continuous recording files which stored in SD card or remote
SAMBA server. User may play or delete the selected file.
53/65
Network Camera User’s Guide
6.1.13 Event Server: Setup FTP/TCP/HTTP/SAMBA server configuration
6.1.13.1 FTP Server
You may setup FTP parameters for further operation of Event Schedule. That’s, if users want
to send the alarm message to an FTP server, it will need to configure parameters here and
also add at least one event schedule to enable event triggering as SMTP.
Name:
User can specify multiple FTP paths as wish. Therefore, user needs to specify a name for
each FTP setting.
FTP Server:
Type the server name or the IP address of the FTP server.
Test:
Check the FTP server whether this account is available or not.
FTP Login name:
Type the user name for the FTP server.
FTP Login Password:
Type the password for the FTP server.
FTP Port:
Set port number of FTP service.
FTP Path:
Set working directory path of FTP server.
FTP Passive Mode:
Select passive or active mode connecting to FTP server.
6.1.13.2 TCP Server
In addition to send video file to FTP server, the device also can send event message to
specified TCP server.
54/65
Network Camera User’s Guide
Name:
User can specify multiple TCP servers as wish. Therefore, user needs to specify a name for
each TCP server setting.
TCP Server:
Type the server name or the IP address of the TCP server.
TCP Port:
Set port number of TCP server.
55/65
Network Camera User’s Guide
6.1.13.3 HTTP Server
The device also can send event message to specified HTTP server.
Name:
User can specify multiple HTTP servers as wish. Therefore, user needs to specify a name for
each HTTP server setting.
URL:
Type the server name or the IP address of the HTTP server.
Test:
Check the HTTP server whether it is available or not.
HTTP Login name:
Type the user name for the HTTP server.
HTTP Login Password:
Type the password for the HTTP server.
Proxy Address:
Type the server name or the IP address of the HTTP Proxy.
Proxy Login name:
Type the user name for the HTTP Proxy.
Proxy Login Password:
Type the password for the HTTP Proxy.
Proxy Port:
Set port number of Proxy.
6.1.13.4 SAMBA Server
The device also can send video stream to specified SAMBA server.
56/65
Network Camera User’s Guide
Name:
User can specify multiple HTTP servers as wish. Therefore, user needs to specify a name for
each HTTP server setting.
SAMBA Server:
Type the server name or the IP address of the SAMBA server.
Test:
Check the SAMBA server whether this account is available or not.
SAMBA Login name:
Type the user name for the SAMBA server.
SAMBA Login Password:
Type the password for the SAMBA server.
SAMBA Path:
Set working directory path of SAMBA server.
57/65
Network Camera User’s Guide
6.1.14 Event Schedule: Configure the event schedule
6.1.14.1 Setting
This menu is used to specify the schedule of Event or Schedule Trigger and activate the
some actions provided by this device. Where the Schedule Trigger will be activated by
user-define interval without event happened.
Name:
Name of the Event or Schedule.
Enable:
Enable or disable this Event or Schedule.
Type:
Event trigger or Schedule trigger.
Enable Time:
Define the feasible time slot.
Trigger by:
Select the triggered sources.
Action:
Define the actions once event triggered.
Example 1:
Send file to FTP server by motion triggered always:
1.
Select event trigger
2.
Enable time: start from 00:00 to 24:00 every day
3.
Trigger by: Motion Area (Added in Event Detection page)
4.
Action : Send FTP (Add in Event Server -> FTP Server page)
58/65
Network Camera User’s Guide
Example 2:
Send file to E-Mail server by motion triggered from Friday 18:00 to Saturday 06:00
1.
Select event trigger.
2.
Enable time: start from Friday 18:00 and keep work in 12 hours, so it will stop on
Saturday 06:00.
3.
Trigger by : Motion Area (Added in Event Detection page)
4.
Action : Send e-mail (Add in E-Mail page)
i、 To email address: You need to input the receiver email address.
ii、 Subject: You could specify the email subject.
iii、 Message: You could specify the email content.
Example 3:
59/65
Network Camera User’s Guide
Enable Voice Alert every 10-minute during 18:00 to 24:00 from Monday to Friday.
1.
Type: Select schedule trigger and interval is 10-minute.
2.
Enable time: Select Monday to Friday, and set start time from 18:00 and keep work in 6
hours.
3.
Trigger by : You do not need to choose it, because this will be triggered every 10 minute
4.
Action : Voice Alert
60/65
Network Camera User’s Guide
6.1.14.2 Record
User can choose the type of record file for event or schedule application.
Record File Type:
Choose a profile to record.
Record File Prefix:
Define the prefix of recorded filename.
Pre-Trigger Duration:
Define the maximum duration of pre-alarm.
Best Effort Duration:
Define the best effort duration of post-alarm.
Max File Size:
Define the maximum buffer size of record file.
61/65
Network Camera User’s Guide
7. Using VLC Player to Access RTSP Streaming
Note 1: This information is provided for convenience only. We will not provide support for the
installation or use of VLC software.
Note 2: The IP address used in the document are the default URLs and are provided for
example purposes only. You will need to use an IP address that is appropriate for your
network.
To use VLC player to view RTSP streaming, follow these step to proceed:
1. Download and install VLC Player (version 1.0.5) from http:\\www.videolan.org\vlc.
2. Launch VLC Player
3. Click Media _Open Network Stream.
4.
5.
6.
7.
On the ‘Network’ tab, choose RTSP under the ‘Protocol’ menu.
Enter the IP address of the stream that you want to view in the ‘Address’ field.
Default URL is as below:
H.264 Profile1
rtsp://192.168.1.30:554/media/media.amp?streamprofile=Profile1
MJPEG Profile2
rtsp://192.168.1.30:554/media/media.amp?streamprofile=Profile2
H.264 Profile3
rtsp://192.168.1.30:554/media/media.amp?streamprofile=Profile3
MJEPG Profile4
rtsp://192.168.1.30:554/media/media.amp?streamprofile=Profile4
H.264 Profile5
rtsp://192.168.1.30:554/media/media.amp?streamprofile=Profile5
MJPEG Profile6
rtsp://192.168.1.30:554/media/media.amp?streamprofile=Profile6
H.264 Profile7
rtsp://192.168.1.30:554/media/media.amp?streamprofile=Profile7
MJPEG Profile8
rtsp://192.168.1.30:554/media/media.amp?streamprofile=Profile8
Enter the login ID and password (admin and 1234 by default).
Click Play and you will see the image streaming.
62/65
Network Camera User’s Guide
3GPP
To use the 3GPP function, in addition to previous section, you might need more information or
configuration to make this function work.
Note that to use the 3GPP function, it strongly recommends to install the Networked Device
with a public and fixed IP address without any firewall protection.
RTSP Port:
Port 554 is the default for RTSP service. However, sometimes, some service providers
change this port number for some reasons. If so, user needs to change this port accordingly.
Dialing procedure:
1.
Choose a verified player (Packet Video or Real player currently)
2.
Use the following URL to access:
rtsp://host/mpeg4/media.3gp
Where host is the host name or IP address of the camera.
3.
Enter the login ID and password (admin and 1234 by default).
Compatible 3G mobile phone:
Please contact your dealer to get the approved list of compatible 3G phone.
63/65
Network Camera User’s Guide
8. Specification
Video
Sensor Type
1/4" image sensor
Active Pixels
1280 x 1024 (HxV)
Compression
H.264 /Motion JPEG
Streaming
Simultaneously multi-profile streaming
Resolution
SXGA, VGA, QVGA, 160x120 (1.3 Mega Mode);
720P, 640x360, 160x90 (720p Mode)
Max. Frame Rate
1.3MP (1280x1024) at 30 fps (NTSC/PAL)
Day/Night
Digital D/N Control
Day/Night Mode
Night Mode / Day Mode / Auto / Schedule
Shutter Time
Range from 1/120s to 1/5s Selectable (60Hz);
Range from 1/100s to 1/4s Selectable (50Hz)
Minimum Illumination
1.6 Lux @50IRE
(Shutter speed: 1/15 sec)
Bit Rate Control
Multi-profile bit rate control: CBR/ VBR/ ECBR/ EVBR
Lens
Type, Focal Length, F-number
Built-in Fixed lens, f=4.3 mm, F1.8 (Mega pixel lens)
View Angle
H: 50°/ V: 38° (1.3MP Mode)
H: 50°/V: 26° (720p Mode)
Audio
Audio Communication
Simplex or Full duplex (2-way audio) Selectable
Compression
RTSP: G.711 64kbps, G.726 32kbps Selectable
3GPP: AMR
Audio In/Out
Built-in microphone
Image Enhancement
Image Settings
AWB, AES
Exposure Mode: Auto/ Hold/Manual;
White Balance: Auto/ Hold;
Exposure Value, Sharpness, Color, Brightness, Contrast: 101
level sensitivity
3D Noise Reduction (De-Noise): Off/ On
Privacy Zone
Yes; customized threshold privacy zone (up to 8)
Image Orientation
Mirror, Flip
Frequency Control
50Hz, 60Hz
Date & Time Stamp
Yes
Test Overlay
Yes
Intelligent Video & Event
Management
Motion Detection
Smart Encoding
Up to 10 customized threshold detection windows with included
or excluded options, 101 detected object size or level sensitivity
Up to 2 Configurable ROI for better picture quality and
bandwidth efficiency
Others
Snapshot, e-PTZ, Optimized i-frame setting, Video Buffer
Events
Motion, Audio detection
Event Actions
File upload via FTP, SMTP, SAMBA(NAS) and SD Card;
Notification via voice alert, email, HTTP and TCP;
Video and audio recording to SD Card or SAMBA
64/65
Network Camera User’s Guide
Store Category
Motion / Schedule
Stores video clips and snapshots
Local Storage
Memory Card Slot
Micro SD / Micro SDHC Card up to 32 GB
Memory Card Overwrite
Yes
Network
Protocol
IPv4, TCP/IP, UDP, HTTP, SMTP, DNS, DHCP, NTP, FTP, RTP,
RTSP, RTCP, ICMP, UPnP, IPv6, HTTPS, DDNS, DIPS, ARP,
Bonjour, IGMP, PPPoE, 3GPP, SAMBA
Ethernet
10/100Mbps; 10Base-T/100Base-TX Ethernet connection for
LAN / WAN, RJ-45
Wireless
-
PoE
-
ONVIF
YES
Browser
IE Browser 6.0 or above
Security
Two-level access with password protection;
IP address filtering;
HTTPS encrypted data transmission
I/O & Controls
Power
DC Jack (2.0mm)
Network
RJ-45 with network LED x2 (Green & Orange)
Audio In/Out
3.5mm Phone Jack 1 out
Reset
More than 5 sec for loading default
Power
Power Requirement
DC 12V ± 10%
Power Consumption (Max.)
3W
Mechanical
Dimensions(WxDxH)
52.6 x 35 x 74.5 mm (2.07” x 1.38” x 2.93”)
Weight
70g (Without Bracket)
Environmental
Operating Temperature
0ºC ~ 40ºC (32ºF ~ 104ºF)
Operating Humidity
20~ 80% RH
Storage Temperature
-20°C ~ 60°C (-4°F ~ 140°F)
Regulatory
Approvals
CE, FCC, RoHS
65/65
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement