User Manual

User Manual
LED-WAV-50W
User Manual
Please read the instructions carefully before use
1A
TABLE OF CONTENTS
1. Safety Introductions
Please read the instructions carefully which includes important
1. Safety Instructions
2. Technical Specifications
information about the installation, operation and maintenance.
WARNING
y
Please keep this User Guide for future consultation. If you sell the unit to another user,
be sure that they also receive this instruction booklet.
3. How To Set The Fixture
y
All fixtures are intact from the manufacturer, please operate follow up the user manual,
artificial fault are not under guarantee repair.
4. How To Control The Fixture
y
Unpack and check carefully that there is no transportation damage before using the
unit.
5. DMX 512 Configuration
6. DMX 512 Connections
y
The unit is for indoor use only. Use only in a dry location.
y
Do install and operate by operator.
y
Use safety chain when fixes the unit. Don’t handle the unit by taking its head only, but
always by taking its base.
7. Troubleshooting
y
The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces.
8. Fixture Cleaning
y
Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.
y
Before operating, ensure that the voltage and frequency of power supply match the
power requirements of the unit.
y
It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
y
Maximum ambient temperature TA : 40℃. Don’t operate it where the temperature is
higher than this.
y
Don’t connect the device to any dimmer pack.
y
First run, there will be smoke or smells, and all disappearing a few minutes later.
y
Make sure there are no flammable materials close to the unit while operating, as it is
fire hazard.
y
Look over power wires carefully, replace immediately if there is any damage.
y
Never run on for a long time lest shortening lifespan.
y
Avoid any inflammable liquids, water or metal objects entering the unit. Once it happen,
cut off the mains power immediately.
y
2A
Do not operate in dirty and dusty environment, also cleaning fixtures regularly.
3A
y
Do not allow children to operate the fixture.
y
Do not touch any wire during operation as there might be a hazard of electric shock.
y
Avoid power wires together around other cables.
y
Disconnect mains power before fuse/lamp replacement or servicing.
y LED: 50W LED
y
Replace fuse only with the same type.
y Fuse: T 6.3A
y
In the event of serious operating problem, stop using the unit immediately.
y Power consumption:80 W
y
Never turn on and off the unit time after time.
y Dimension: 279 x226 x 191 mm
y
The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly
y Weight:4 kg/pcs
2. Technical Specifications
y Voltage:AC 100-240V~ 50/60Hz
damaged.
y
Do not open the unit as there are no user serviceable parts inside.
y
Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead
to damage or malfunction. Please contact the nearest authorized technical assistance
center.
3. How To Set The Fixture
y
Disconnect the mains power if the fixture is not used for a long time.
3.1
y
Do use original packing materials once transport it again.
y
Do not look directly at the LED light beam while the fixture is on.
Control Panel
For power supply, do not connect in series much more than 7 units, use another
mains supply for next 7 units.
Installation
The unit should be mounted via its screw holes on the bracket. Always ensure that the unit
is firmly fixed to avoid vibration and slipping while operating. Always ensure that the
structure to which you are attaching the unit is secure and is able to support a weight of 10
times of the unit’s weight. Also always use a safety cable that can hold 12 times of the
weight of the unit when installing the fixture.
The equipment must be fixed by professionals. And it must be fixed at a place where is out
of the touch of people and has no one pass by or under it.
4A
1
○
Display: To show the various menus and the selected functions
5A
2
○
3
○
4
○
safety cable that can hold 10 times of the weight of the unit when installing the fixture.
LED:
DMX
On
DMX input present
MASTER
On
Master Mode
SLAVE
On
Slave Mode
Sound
On
No function
C. Replace the lens
You could replace the other lens if you want to, as following picture.
Button:
MENU
To select the programming functions
DOWN
To go backward in the selected functions
UP
To go forward in the selected functions
ENTER
To confirm the selected functions
Only for remote control: Connecting with CA-8/UC3 to control the unit for
Stand by, Function and Mode function
You should screw the lens roller to take it down as NO.1, and bring the lens out as No.2.
Then you could replace the lens that you want to.
Notes: the lens roller has two slots for the lens; you should pay more attention that the latest
slot is for the 34°lens, and the far slot is for 60°lens.
3.3
Main Function
To select any functions, press MENU button until the required one is shown on the display.
Select the function by ENTER button and the display will blink. Use DOWN and UP button to
5
○
DMX output: For DMX512 link, use 3-pin XLR plug cable to link the next unit
6
○
DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal
change the mode. Once the required mode has been selected, press ENTER button to
setup or it will automatically return to the main functions without any change after idling one
minute. Back to the functions without any change press MENU button. The main functions
7 Mains input: Connect to supply mains power for the unit
○
are shown below:
8 Mains output: Connect and supply mains power for the other unit
○
9 cooling system: for cooling down the unit
○
3.2
Installation
A. Product Items
z
User manual
z
60°lens
B.
Mounting
You can install the unit on the truss or ceiling; Use clamps to fix the unit to truss. Always
ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always
ensure that the structure to which you are attaching the unit is secure. Also always use a
6A
7A
Slave Mode
is showing on the display. Pressing ENTER
Press the MENU button up to when the
button and the display will blink. Use DOWN and UP button to select the
(set the
(set the fixture as slave). Once the mode has been selected,
fixture as master) or
press the ENTER button to setup or automatically return to the main functions without any
change after one minute. To go back to the functions without any change press the MENU
button again.
Display Inverse
is blinking on the display. Use DOWN and UP button to
Press MENU button until
select
(display normal) or
(display inverse), press ENTER button to setup.
LED display
Press the MENU button up to when the
is shown on the display. Pressing ENTER
button and the display will blink. Use DOWN and UP button to select
(display
(display off 20 seconds after exit menu) mode. Once select, press
always on) or
ENTER button to setup or exit menu mode without any change after one minute. Back to the
functions without any change press MENU button again.
Manual setting color
is shown on the display. Pressing ENTER
Press the MENU button up to when the
button,
DMX 512 Address Setting
and
use
DOWN
and
UP
button
(000-2555,clockwise/counterclockwise), or
to
select
(0-255)
or
(125-255),press ENTER button
is shown on the display. Pressing ENTER
to confirm and use DOWN and UP button to adjust the value, once select press ENTER
button and the display will blink. Use DOWN and UP button to change the DMX 512 address.
button to setup or automatically exit menu mode without any change after one minute. To go
Once the address has been selected, press ENTER button to setup or automatically exit
back to the last function without any change press the MENU button.
Press the MENU button up to when the
menu mode without any change after one minute. Back to the previous functions without
any change press MENU button.
Self-test
Press the MENU button up to when the
8A
is shown on the display, Pressing ENTER
9A
button to run the auto test. Back to the functions without any change press MENU button.
setting will be effected at once. Every time you turn the unit on, it will show “CP21” on the
Back to the functions without any change press MENU button.
display and move all the motors to their ‘home’ position. After that the unit will be ready to
receive DMX signal or run the built in programs.
Temperature Test
is blinking on the display. Pressing ENTER
Press the MENU button up to when the
4.1 Master/Slave Built In Preprogrammed Function
button and the display will show the temperature of the unit. To go back to the functions
The fixture will allow you to link 2 fixtures together and operate without a controller. In
press the MENU button again.
Master/Slave mode, the first fixture whose DMX input jack has with nothing connect need to
set as master and the other unit need to set as slave 1 via menu, then the first unit will
Fixture Hours
control the other to give an automatic and synchronized light show. This function is good
Press the MENU button up to when the
is blinking on the display. Pressing ENTER
when you want an instant show. Any fixture can act as a Master or as a Slave.
button and the display will show the number of working hours of the unit. To go back to the
functions press the MENU button.
4.2. Easy Controller (by CA-8)
Software version
The easy remote control is used only in master/slave mode. By connecting to
is showing on the display. Pressing ENTER
the 1/4” microphone jack of the first unit, you will find that the remote controller
button and the display will show the version of software of the unit. To go back to the
on the first unit will control all the other units for Stand by, Function and Mode
functions press the MENU button again.
selection
Press the MENU button up to when the
Blackout To blackout all the fixture
Factory reset all channels
Press the MENU button up to when the
is shown on the display, press ENTER
button to setup. Back to the functions without any change press MENU button.
Hold and press for 3 seconds:
Function Water wave speed:1-3 1. Clockwise/counterclockwise/color
2. choose color
Mode
LED OFF
Color speed:1-3
LED blinking
LED ON
4.3 DMX Controller
4. How To Control The Unit
Use universal DMX controller to control the units, you have to set DMX address from 1 to
You can operate the unit in three ways:
512 channel so that the units can receive DMX signal.
1. By master/slave built-in preprogram function
Press the MENU button up to when the
2. By easy controller
button and the display will blink. Use DOWN and UP button to change the DMX512 address.
3. By DMX controller
Once the address has been selected, press and keep ENTER button pressed up to when
is showing on the display. Pressing ENTER
No need to turn the unit off when you change the DMX address, as new DMX address
the display stops blinking or storing automatically one minute later. To go back to the
10A
11A
functions without any change press the MENU button again. If you use please refer to the
following diagram to address your DMX512 channel for the first 4 units.
3 channels:
5. DMX512 Configuration
1.
Connect the fixture together in a “daisy chain” by XLR plug cable from the output of the
fixture to the input of the next fixture. The cable cannot be branched or split to a “Y”
cable. Inadequate or damaged cables, soldered joints or corroded connectors can
easily distort the signal and shut down the system
2.
The DMX output and input connectors are pass-through to maintain the DMX circuit
when one of the units’ power is disconnected.
3.
At last fixture, the DMX cable has to be terminated with a terminator to reduce signal
errors. Solder a 120-ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a
3-pin XLR-plug and plug it in the DMX-output of the last fixture.
4.
Each lighting fixture needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
5.
3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+),
6. DMX512 Connections
The DMX512 is widely used in intelligent lighting control, with a maximum of 512 channels.
12A
Pin4/5: not used
13A
7. Troubleshooting
Following are a few common problems that may occur during operation. Here are some
suggestions for easy troubleshooting:
A. The fixture does not work, no light
1. Check the connection of power and main fuse.
2. Measure the mains voltage on the main connector.
B. Not responding to DMX controller
1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly.
2. If the DMX LED is on and no response to the channel, check the address settings and
DMX polarity.
3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB
of the fixture or the previous one.
4. Try to use another DMX controller.
5. Check if the DMX cables run near or run alongside to high voltage cables that may
cause damage or interference to DMX interface circuit.
C. Some fixtures don’t respond to the easy controller
1. You may have a break in the DMX cabling. Check the LED for the response of the
master/ slave mode signal.
2. Wrong DMX address in the fixture. Set the proper address.
D. No response to the sound
1. Make sure the fixture does not receive DMX signal.
2. Check microphone to see if it is good by tapping the microphone.
E. One of the channels is not working well
1. The stepper motor might be damaged or the cable connected to the PCB is broken.
2. The motor’s drive IC on the PCB might be out of condition.
8. Fixture Cleaning
The cleaning of internal must be carried out periodically to optimize light output. Cleaning
frequency depends on the environment in which the fixture operates: damp, smoky or
particularly dirty surrounding can cause greater accumulation of dirt on the fixture’s optics.
y Clean with soft cloth using normal glass cleaning fluid.
y Always dry the parts carefully.
Innovation, Quality, Performance
y Clean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
14A
15A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement