ADAPTTM Colibri

ADAPT Colibri
TM
Active communicative air diffuser for the WISE system, ADAPT C
ADAPT Colibri
Quick facts
Ź Supply air diffuser with an active damper
Ź Pressure-dependent and cleanable
Ź Integrated sensor module
Ź Simple wiring, Plug & Play
Ź Communication via Modbus RTU
Ź Supplied complete with junction box, CONNECT Adapt
Ź Complemented with the WISE templates,
containing detailed descriptions for planning
Ź Allows for control of:
– Heat alternatively, cooling valve
(max. 3 actuators per master)
– Slaves (supply or extract air, 3 pcs)
– Lighting (via relay)
Quick Selection
AIR FLOW – SOUND LEVEL – COOLING EFFECT
max q (l/s)
Size
min q*)
(l/s)
50 Pa / 30 dB(A)
150 Pa / 35 dB(A)
max p**)
(W)
160
0/5
55
60
530
250
0/10
85
90
860
*)
The first value indicates closed damper, the second value
indicates lowest adjustable air flow.
**)
Max. cooling effect is calculated at 't=8K and for an air
flow at 50 Pa and 30 dB(A).
1
WISE
Technical Description
Design
ADAPT is a series of flow-controlled supply air diffusers for
the Swegon WISE system:
s The air diffuser controls the airflow with an active damper
inside the commissioning box, see figure 1.
s An ADAPT diffuser is always supplied with a
commissioning box.
s Inside the air diffuser, is a controller providing all the
required set points and control functions as well as a
multi-functional sensor module, see figure 1.
Functions in the Master diffuser
s Cools/heats and ventilates with air.
s Two stage cooling with water in the second stage, cannot
be combined with heating.
s Controls airflow with regard to temperature and presence.
s Ventilation boost after longer periods of unoccupancy.
s Provision for wiring to a CO2 controller.
s Provision for manually setting set points.
s Has provision for connection to a main control system
(Modbus).
s Emergency functions for closing / opening of the damper.
s Control of the heating in sequence unless 2-stage
cooling has been selected.
s Indication via LED. Indicates current operating mode and
warns of malfunctions in the diffuser.
s Comfort control indicated by the LED if the room temperature or CO2 value deviates too much from the set point,
not activated by default.
Planning – WISE Templates
See separate documentation, ”WISE Project manual”,
available for download from www.swegon.se.
In addition, Swegon sales personnel can supply WISE
templates containing descriptions with detailed information
regarding functionality, flowcharts, wiring diagrams and
demarcation list for various constructions.
1
2
Sensor module
A sensor module is integrated in all ADAPT supply air
diffusers, containing the following functions:
s A temperature sensor controls the airflow to maintain
required temperature in the room.
s A presence detector makes it possible to save additional
energy by lowering the airflow when there are no occupants in the room.
s The presence signal from the air diffuser can be fetched
for controlling the lighting, for instance, and in this way
save more energy.
3
Figure 1. The sensor module of ADAPT Colibri
with connection for TUNE Adapt.
1. Temperature detector
2. In-operation indicator, green, red and orange LED.
3. Presence detector
Connectivity
In each delivery of a master diffuser, a CONNECT Adapt
junction box is included:
s The junction box replaces the coupling box which otherwise is mounted on a wall/ceiling for wiring a 24 V supply
voltage to the air diffuser and Modbus networks.
s Both air diffuser and junction box are equipped with RJ45
quick-fit connectors for quick and fault-free wiring.
s The device has provision for connection to a main control
system (BMS/SCADA) via ModBus.
s Accessory cable, LINK Modbus (RJ12) can be connected
between air diffuser and junction box. The air diffuser will
then be ready for the main control system.
s From the junction box, control functions for heating in
sequence, CO2 sensor and set point adjuster, can also be
connected.
2
Swegon reserves the right to alter specifications.
Figure 2. Junction box, CONNECT Adapt.
20121114
www.swegon.com
WISE
Installation
Maintenance
A detailed installation instruction is enclosed with each
delivery and can also be downloaded from www.swegon.
s The ADAPT air terminals can be cleaned on the outside, if necessary, using lukewarm water with dishwashing detergent added.
s The duct system is accessible without need for tools.
(See the separate installation instruction)
1. The commissioning box can be suspended from a ceiling
and connected to duct system. Use hanger system A or B.
2. Press the ADAPT Colibri air diffuser into the outlet of
the commissioning box and secure it with screws or pop
rivets. Readjust the hanger rods of the commissioning box
if needed, so that the air diffuser sits tight against the ceiling, or the framework of the modular suspended ceiling.
Declaration
Declaration of Construction Materials is available for download from www.swegon.com.
Electrical data
ADAPT is supplied with power via the junction box.
For more information about various wiring and room solutions, see the Technical Section.
A
Supply voltage
B
24 V AC ±10 %
Max. power consumption
3 VA
Cable rating
0,6 A
0 °C - +50 °C
Forms of delivery
s Some of the ADAPT-products are available from stock
with standard settings.
s At delivery, a master air diffuser contains a complete air
diffuser with commissioning box, junction box CONNECT
Adapt and 5 metre long RJ45 cable LINK Adapt.
s Delivery of a slave air diffuser contains a complete air diffuser with commissioning box and 5 metre long RJ45
Standard settings
Temperatures (°C)
Presence
22
±1K
Absence
22
+3 / -2 K
Commissioning
Night-time cooling
18
s Normally, the ADAPT air terminals are preset from the
factory based on design values.
s The TUNE Adapt hand-held terminal is used for manually checking the current air flow through the air diffuser, and for changing set points, if required.
s For more information, see the installation - Commissioning - Maintenance instruction as well as the TUNE
Adapt user manual.
Morning heat
25
Airflows (l/s)
Absence
Min.
airflow
Max.
airflow
The smallest size
0/5
10
60
The largest size
0/10
15
90
Air quality (ppm)
Min.
Max.
800
1000
Materials and finish
Presence
s ADAPT air terminals are made of galvanized sheet steel,
with parts made of plastic, rubber and also contain
electronic components.
s The ADAPT air terminals are powder coated in Swegon’s white interior standard colour RAL 9010, both on
the inside and on the outside.
s The sensor module and junction box are made of ABS
plastic.
s The commissioning box is made of galvanized sheet
steel with internal insulation.
Switch on delay
Figure 3. Adapt Colibri, installation.
Swegon reserves the right to alter specifications.
CO2
Switch out delay
0 sec.
20 min.
Communication Modbus RTU by RS-485
Modbus ID
Speed
1
38,400 bps
Bit length
8 bits
Stop bits
1 bit
Parity
20121114
None
www.swegon.com
3
ADAPT Colibri
Ambient temperature
WISE
Sizing
Engineering graphs
s The specified sound levels dB(A) are applicable to
rooms with an equivalent sound absorption area of 10
m2 (4 dB room attenuation).
s The throw L0.2 is measured under isothermal discharge
conditions.
s Recommended max. permitted temperature below
room temperature is 12 K.
s All technical data applies to 360° distribution pattern.
s For calculating the air stream propagation, air velocities
in the occupancy zone, or sound levels in rooms with
other dimensions, we refer to our ProAir Web calculation
program. ProAir Web is available at www.swegon.com.
Air flow – Pressure drop – Sound level – Throw
s The diagrams should not be used for commissioning.
s The dB(C) value is normally 6-9 dB higher than the
dB(A) value.
s Sizing example – size 160:
– Given airflow 10-50 l/s at Pt 50 Pa.
– Max. sound level 27 dB(A)
– Throw = 2,0 m
m
in
ADAPT C 160
40 dB(A)
1000
Sound data
35
500
400
Sound power level, Lw (dB)
Table, Kok
Size
m
ax
pt Pa
30
300
25
200
20
Mid-frequency (Octave band) Hz
100
63
125
250
500
1000 2000 4000 8000
160
0
7
5
-2
-6
-10
-13
-7
250
1
5
2
-1
-3
-9
-12
-10
Tol. ±
2
2
2
2
2
2
2
2
50
40
30
20
3
4
5
10
20
Sound attenuation 'L
Table 'L
125
250
500
1000 2000 4000 8000
160
15
9
9
20
19
15
16
14
250
13
8
10
19
16
13
16
16
Tol. ±
2
2
2
2
2
2
2
2
0,3
20
50
0,4 0,5
30
40
50
100
200 l/s 300
100
200
300
400 500
1
2
3
4
m3/h
5
10
l0,2 m
ADAPT C 250
pt Pa
40 dB(A)
1000
m
ax
Mid-frequency (Octave band) Hz
63
40
m
in
Size
0,2
30
35
500
400
30
300
200
25
20
100
50
40
30
20
4
5
10
20
30
0,2
4
Swegon reserves the right to alter specifications.
20121114
20
40
0,3
50
0,4 0,5
30
40
100
50
200
1
100
300
2
200
3
4
300 l/s 400
1000 m3/h
400 500
5
www.swegon.com
10
l0,2 m
WISE
Dimensions and weights
Ordering key
Size
A
B
C
ØD
Ød
160
595x595
504
332
159
250
250
595x595
622
388
249
315
Size
E
F
G
H
K
Weight, kg
160
314
201
214
450
100
8,5
Connection dimensions:
250
395
300
247
575
140
11,3
M: Master, S: Slave
Product
Rectangular active air diffuser
for ceiling
ADAPT C
c
-bbb
-c
Version:
N.B.! Specify absence, min./max. airflows in your specification!
CL = Center line
Standard range:
Size: 160, 250
Accessories
DETECT Quality Temperature and CO2sensor with set point
selector knob
E
Hand-held terminal for reading/changing
settings
TUNE Temp
Temperature adjuster
LINK Modbus
RJ12-cable for connecting up Modbus RTU
LINK Adapt
RJ45 cable for connecting up in other lengths
SPLIT Link
Split connector
FIX Link
For securing cords to ducts, etc.
POWER Adapt
Transformer
ACTUATOR
Valve actuator, on/off
VALVE
Radiator valve
ADAPT Relay
Relay for light or heat control
ADAPT TR
Semi-conductor relay for lighting or heat
control
CABLE Ext
Extension cable between box and air diffuser
LINK Wa
Network cable for Modbus, complies with the
EIA-485 standard
Figure 4. ADAPT Colibri, dimension figure.
Each accessory is described in more detail in a separate
product sheet available at www.swegon.se.
Swegon reserves the right to alter specifications.
20121114
www.swegon.com
5
ADAPT Colibri
F
TUNE Adapt